Search Results

Search found 36498 results on 1460 pages for 'linux usb drive'.

Page 53/1460 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

  • How to make Windows 7 use the internet connection that I specify

    - by user138957
    I have a LAN adapter and a USB wireless internet connection. When both connected windows 7 always uses the USB. I tried changing the metric values but no luck. Let me explains the steps I took. Currently automatic metric on all adapters. LAN connected. ipconfig shows that it is connected to the correct ip/dns/gateway etc. IPv4 Route table shows Metric 24 Then connected USB. ipconfig shows USB connectivity then LAN in that order. Internet is now through USB. IPv4 Route table shows Metric 4249 for LAN and USB is 41. Gateway for USB shows "on-link". netstat -rn shows USBDEVICE on top. Changed LAN metric to 5 and now the route table shows LAN as 9 (not sure why it added 4) and USB as 41. netstat shows LAN then USB. ipconfig shows LAN then USB. But still connection is through USB. How do I know? Task manager shows utilization only through USB as well as speed is showing around 1mbps rather than LANs 10mbps. How can I get win7 use LAN while USB is connected. I am just trying to use USB as a backup just in case I lose LAN connection. Please help!! I thought i will make USB metric manually to say 10. But it says I have to reconnect for it to be effective. Currently USB still shows below LAN and still has 9 and 41 in the table. Disconnected USB. Table shows LAN metric as 24 (Not sure why it got changed from 9 and setting got reverted by to automatic) Reconnected USB. Now in the setting still shows 10 and the route table shows 11 for USB and LAN shows 4249 (settings shows 4245, 4 less)) For some reason restarting USB is resetting LAN setting when reconnected. Thanks

    Read the article

  • How to find the /dev name of my USB device

    - by mustafa
    I am running Ubuntu 11 on VmWare on Windows XP. I want to format an SD card in Ubuntu. But, I can't figure out which /dev/xxx device the SD card is. I plug the card into the built-in socket of my laptop. I "safely remove" the device in Windows. Then, I "connect" the PCMCIA reader in VmWare. Now, I was supposing to see a new device like /dev/sdx. But, it doesn't appear :( How can I find what the name of my USB device's name and mount it? /var/log/message is empty. Here is the output of dmesg: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd And, here is the last lines of /var/log/syslog: Oct 31 18:51:21 ubuntu kernel: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd Oct 31 18:51:21 ubuntu mtp-probe: checking bus 2, device 12: "/sys/devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-1" Oct 31 18:51:21 ubuntu mtp-probe: bus: 2, device: 12 was not an MTP device

    Read the article

  • which drive do I mount

    - by Crash893
    I have a system hdd then two raid1 hard drives I see that sda1 is the system drive but when i do a fdisk -l I get the following results so which of the following do i need to mount to get the "raid" drive and not the individual hdd? root@Mxxxx-PDC:/etc/samba# fdisk -l Disk /dev/sda: 251.0 GB, 251000193024 bytes 255 heads, 63 sectors/track, 30515 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000762dc Device Boot Start End Blocks Id System /dev/sda1 * 1 30328 243609628+ 83 Linux /dev/sda2 30329 30515 1502077+ 5 Extended /dev/sda5 30329 30515 1502046 82 Linux swap / Solaris Disk /dev/sdb: 400.0 GB, 400088457216 bytes 255 heads, 63 sectors/track, 48641 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x00000000 Device Boot Start End Blocks Id System /dev/sdb1 1 48641 390708801 83 Linux Disk /dev/sdc: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x0009f4b2 Device Boot Start End Blocks Id System /dev/sdc1 * 1 255 2048256 fd Linux raid autodetect /dev/sdc2 256 30401 242147745 fd Linux raid autodetect Disk /dev/sdd: 250.0 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000b7f4c Device Boot Start End Blocks Id System /dev/sdd1 * 1 255 2048256 fd Linux raid autodetect /dev/sdd2 256 30401 242147745 fd Linux raid autodetect

    Read the article

  • Dismount USB External Drive using powershell

    - by JC
    Hello, I am attempting to dismount an external USB drive using powershell and I cannot successfuly do this. The following script is what I use: #get the Win32Volume object representing the volume I wish to eject $drive = Get-WmiObject Win32_Volume -filter "DriveLetter = 'F:'" #call dismount on that object there by ejecting drive $drive.Dismount($Force , $Permanent) I then check my computer to check if drive is unmounted but it is now. The boolean parameters $force and $permanent have been tried with different permutations to no avail. The exit code returned by the dismount command changes when the params are toggled. (0,0) = exit code 0 (0,1) = exit code 2 (1,0) = exit code 0 (1,1) = exit code 2 The documentation for exit code 2 indicates that there are existing mount points as a reason why it cannot dismount. Although I am trying to dismount the only mount point that exists so I am unsure what this exit code is trying to tell me. Having already trawled the web for people experiencing similar problems I have only found one additional command to try and that is the following: # executed after the .Dismount() command $drive.Put() This additional command does not help. I am running out of things to try, so any assistance anyone can give me would be greatly appreciated, Thanks.

    Read the article

  • Usb WiFi dongle pluggin in doesnt create wlan0 interface

    - by zuba
    I use D-Link DWA-110 WiFi usb dongle. It used to be working well, but after some config changes I broke something and now when I plug the dongle in I see it in lsusb output, but wlan0 isn't created and the led on the dongle doesn't light. What to check out? ~ > uname -a Linux Distress 3.2.0-56-generic #86-Ubuntu SMP Wed Oct 23 17:31:43 UTC 2013 i686 i686 i386 GNU/Linux dmesg shows [ 667.824095] usb 1-8: new high-speed USB device number 6 using ehci-pci [ 668.117996] usb 1-8: New USB device found, idVendor=07d1, idProduct=3c07 [ 668.118007] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 668.118015] usb 1-8: Product: 802.11 bg WLAN [ 668.118021] usb 1-8: Manufacturer: Ralink

    Read the article

  • How and why are operating systems bootable from a USB?

    - by user114638
    I'm told to install ubuntu on my laptop for work in order to learn shell scripting. I've read the best way is to install ubuntu on a USB stick and partition my HDD. I'm curious how an OS is bootable from a USB stick? Is it literally just a small interface that can be put anywhere? This reminds me of a time I downloaded a game onto my USB stick, when I brought it to my friends house he told me it will run slow if I don't install it and only run it from the usb, is this different from running ubuntu from a usb? Will ubuntu be slow?

    Read the article

  • linux raid 1: right after replacing and syncing one drive, the other disk fails - understanding what is going on with mdstat/mdadm

    - by devicerandom
    We have an old RAID 1 Linux server (Ubuntu Lucid 10.04), with four partitions. A few days ago /dev/sdb failed, and today we noticed /dev/sda had pre-failure ominous SMART signs (~4000 reallocated sector count). We replaced /dev/sdb this morning and rebuilt the RAID on the new drive, following this guide: http://www.howtoforge.com/replacing_hard_disks_in_a_raid1_array Everything went smooth until the very end. When it looked like it was finishing to synchronize the last partition, the other old one failed. At this point I am very unsure of the state of the system. Everything seems working and the files seem to be all accessible, just as if it synchronized everything, but I'm new to RAID and I'm worried about what is going on. The /proc/mdstat output is: Personalities : [raid1] [linear] [multipath] [raid0] [raid6] [raid5] [raid4] [raid10] md3 : active raid1 sdb4[2](S) sda4[0] 478713792 blocks [2/1] [U_] md2 : active raid1 sdb3[1] sda3[2](F) 244140992 blocks [2/1] [_U] md1 : active raid1 sdb2[1] sda2[2](F) 244140992 blocks [2/1] [_U] md0 : active raid1 sdb1[1] sda1[2](F) 9764800 blocks [2/1] [_U] unused devices: <none> The order of [_U] vs [U_]. Why aren't they consistent along all the array? Is the first U /dev/sda or /dev/sdb? (I tried looking on the web for this trivial information but I found no explicit indication) If I read correctly for md0, [_U] should be /dev/sda1 (down) and /dev/sdb1 (up). But if /dev/sda has failed, how can it be the opposite for md3 ? I understand /dev/sdb4 is now spare because probably it failed to synchronize it 100%, but why does it show /dev/sda4 as up? Shouldn't it be [__]? Or [_U] anyway? The /dev/sda drive now cannot even be accessed by SMART anymore apparently, so I wouldn't expect it to be up. What is wrong with my interpretation of the output? I attach also the outputs of mdadm --detail for the four partitions: /dev/md0: Version : 00.90 Creation Time : Fri Jan 21 18:43:07 2011 Raid Level : raid1 Array Size : 9764800 (9.31 GiB 10.00 GB) Used Dev Size : 9764800 (9.31 GiB 10.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 0 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:27:33 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : a3b4dbbd:859bf7f2:bde36644:fcef85e2 Events : 0.7704 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 17 1 active sync /dev/sdb1 2 8 1 - faulty spare /dev/sda1 /dev/md1: Version : 00.90 Creation Time : Fri Jan 21 18:43:15 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:39:06 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 8bcd5765:90dc93d5:cc70849c:224ced45 Events : 0.1508280 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 18 1 active sync /dev/sdb2 2 8 2 - faulty spare /dev/sda2 /dev/md2: Version : 00.90 Creation Time : Fri Jan 21 18:43:19 2011 Raid Level : raid1 Array Size : 244140992 (232.83 GiB 250.00 GB) Used Dev Size : 244140992 (232.83 GiB 250.00 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:46:44 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 1 Spare Devices : 0 UUID : 2885668b:881cafed:b8275ae8:16bc7171 Events : 0.2289636 Number Major Minor RaidDevice State 0 0 0 0 removed 1 8 19 1 active sync /dev/sdb3 2 8 3 - faulty spare /dev/sda3 /dev/md3: Version : 00.90 Creation Time : Fri Jan 21 18:43:22 2011 Raid Level : raid1 Array Size : 478713792 (456.54 GiB 490.20 GB) Used Dev Size : 478713792 (456.54 GiB 490.20 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 3 Persistence : Superblock is persistent Update Time : Tue Nov 5 17:19:20 2013 State : clean, degraded Active Devices : 1 Working Devices : 2 Failed Devices : 0 Spare Devices : 1 Number Major Minor RaidDevice State 0 8 4 0 active sync /dev/sda4 1 0 0 1 removed 2 8 20 - spare /dev/sdb4 The active sync on /dev/sda4 baffles me. I am worried because if tomorrow morning I have to replace /dev/sda, I want to be sure what should I sync with what and what is going on. I am also quite baffled by the fact /dev/sda decided to fail exactly when the raid finished resyncing. I'd like to understand what is really happening. Thanks a lot for your patience and help. Massimo

    Read the article

  • How can I tell if my hard drive(s) have Battery Backed Write Cache?

    - by Riedsio
    How can I tell if my hard drives have a battery backed write cache (BBWC)? How can I tell if it is enabled and/or configured correctly? I don't have physical access to my server. It's a GNU/Linux box. I can provide supplemental incremental information/details as requested. My frame of reference is that of a DBA -- I have access and privileges, but (usually) only tread where I know am supposed to. :)

    Read the article

  • Use of double pointer in linux kernel Hash list implementation

    - by bala1486
    Hi, I am trying to understand Linux Kernel implementation of linked list and hash table. A link to the implementation is here. I understood the linked list implementation. But i am little confused of why double pointers is being used in hlist (**pprev). Link for hlist is here. I understand that hlist is used in implementation of hash table since head of the list requires only one pointer and it saves space. Why cant it be done using single pointer (just *prev like the linked list)? Please help me.

    Read the article

  • Getting USB boot to work in SmartOS on HP ProLiant N40L

    - by user126579
    I recently downloaded SmartOS and tried running it on my HP ProLiant N40L, but it always fails on boot. After dd'ing the image to the USB stick, I plug it into the internal USB header and turn the machine on. After selecting from GRUB, it displays the following: , bss=0x0 It sits there for 2-4 minutes, then finally boots the OS and displays the following: WARNING: Couldn't read ACPI SRAT table from BIOS. lgrp support will be limited to one group. SunOS Release 5.11 Version joyent_20120614T184600Z 64-bit Copyright (c) 2010-2012, Joyent Inc. All rights reserved. WARNING: kvm: no hardware support After that, it hangs. I've tried this with two different USB sticks. I've seen some mentions on the SmartOS website about people running it on an N40L, booting from USB, so maybe it's just broken hardware? Has anyone gotten this working?

    Read the article

  • Is there a Linux distro that will easily run "embedded style" on a Raspberry Pi?

    - by Dan Harper
    I need a Linux distro that will give me the following: Run on a Raspberry Pi Can reliably survive power loss (like via a read-only filesystem) I've been able to hunt down some documentation on how to change a regular Linux distro over to read-only mode. I was hoping that there would be a distro already built that was designed to run in an embedded environment. I don't need many packages or drivers, just enough to have the Pi working with USB/Ethernet. I don't need any GUI interface or anything, this will just be running a custom service built in C. Does anyone know of a distro that would fit?

    Read the article

  • Choosing a very basic Linux distro with minimal boot time?

    - by user30961
    I've had Ubuntu for a year now, like it but it doesn't match my needed configuration for my old laptop. So... I am using Linux mainly for webapps so I don't care much about user interface. What I need is a distro which is small enough to install on a SD memory card (or USB) since I am removing the hard drive, all my data is in the cloud. I also want it to have as short boot time as possible. I tried Puppy Linux and it seems ok but it had preinstalled looots af small apps I don't need, I would really like to have a distro with minimal preinstallations and add them on my own. So what are my choices and why would you recommend these?

    Read the article

  • How do I get my Nvidia monitor position settings (in Linux) to persist after a restart?

    - by machineghost
    I have two monitors, and I run them both in Linux using the proprietary Nvidia drivers with "TwinView". I just installed Linux Mint 13, and since the install after every reboot my monitors come up in the wrong position (the computer thinks the left monitor is on the right). After boot-up I can run the Nvidia config and fix the monitors' position, and I can even save the configuration file successfully. But as soon as I restart again, the monitors re-appear switched. Does anyone have any idea what might be causing this (and more importantly, how I can solve it?)

    Read the article

  • Does any know fix/cause of USB drives that lose connection

    - by Burch Kealey
    I have been having significant problems trying to copy files to a USB drive (G0-Flex 1.5 tb) No matter what I use to try to copy the files (python code, Windows copy and paste or Drobo Copy utility) I ultimately get a failure. The failure is always some indication that the device is not ready or able to be written to. I am pretty sure the problem is that the drive is losing its connection. I have done everything I can find so far including setting the USB Root hub to never turn off the power, I updated some usb drivers etc. I have found references to this problem primarily with Win7-64 bit. I have also had USB connection problems with other devices- we kept losing a connection to our Bravo Disc Publisher when we went to Win7 and finally bought a newer model and have not had problems since. Any pointers about diagnosing and or understanding the problem would be appreciated.

    Read the article

  • UBUNTU Desktop Installation 9.10 via USB (boot)

    - by user277980
    i have made a live boot usb using UnetBootIn tool for ubuntu desktop 9.10 , i have windows xp sp2 installed as primary os and i want to make a partition for ubuntu but when i try to boot it via usb , it just goes to boot menu of ubuntu , then i enter the default type for installation after that nothing happens , just the ubuntu logo showed up and just that nothing happens after that , i can try the simpler task also i.e.via cd install but i want to know what's not working with this usb boot method Thnx n Advance

    Read the article

  • Installing Windows XP sp3 into USB 2.0 WD 320Gb Hard Drive

    - by NetKabuki
    I have a HP laptop with support for 3 USB 2.0 ports. I also have a clean 320Gb WD USB 2.0 drive. The HP can boot from USB (Bios options). I used the install disk (XP SP3 bootable) and after a few stutters, was actually able to load up a partition on the 320Gb drive with Windows. I cannot consistently get the system to boot up off the USB drive. I am able to drop Ubuntu on that same WD drive and boot up. I can even get Grub2 on Ubuntu to recognize the Win OS. But booting the Win OS is an impossible task. What can I do differently - if anything?

    Read the article

  • Can you change the name of a flash drive on the boot menu?

    - by Mark Kramer
    I have two Staples brand Flash Drives. They work fine and they boot okay, but they have the same name on the boot menu, so when I have them both in the computer, I can't tell which one is the one I want to boot into. One has Ubuntu on it, the other BackTrack 5. However, the name of those drives show up different on different BIOS. What parameters affect what name shows up for a boot device and how

    Read the article

  • HID USB Very Strange Problem...

    - by Lasanha
    I realy hope some one can help me here cause i search all over the web and nothing comes up.. I allways used PS/2 KB and Mouse and a USB KeyPad (Genius ErgoMedia 500 Gaming Explorer) to play some games, mmorpg, fps, you named, very good whit 11 keys whit possible macros etc etc... Now it comes the problem, i have a USB mouse that have 4 extra buttons, and i need more button, i love buttons.. Well, i plug in the USB mouse and disconectes de PS/2. Everything is ok until i toutch the mouse. If i do so, the ErgoMedia goes off, then on, then i mouse the mouse or press a button and all over again. Yesterday i went buying a new mouse that i liked, a USB mouse too (NPlay whit macros and all that stuff 3600dpi...) Hoping the problem was only whit the other mouse, but no.. It does the exact same thing, ErgoMedia keeps disconecting and conecting everytime i toutch the mouse. What i allready did: Update drivers of both mouses Update drivers of ErgoMedia (no specific drivers(Windows based)) Update drivers of MB Chipset (Actualy no, cause it was up to date allready) Trying other USB Ports (4 Ports back, 4 Ports Front and even 1 Port in 16 card slot device) Disable the "Allows Windows to shut down the energy bla bla" thing in Device Setings. Look up in the Device Setings only apear a problem on the ergomedia (Human interface Device) when i move the damm mouse.. Using Everest to read behavier, everything normal, exepts the disconecting thing, but no errors. Not a power suply, only the ErgoMedia and the mouse are in the USBs, and i allready disable the 16 card reader whit one usb slot to see.. Clean the IRQ registry. Look the entire internet for a fix solution. Help others problems wile looking for a fix for me (Im not a pro but not a completly stupid) Talking to you beggin you to help me as a last resorce... Machine: Acer M3641 Core2Quad 64x Based OS Vista 64b 4GbRAM HD Audio and Graphics I realy hope some one out there knows a fix for this, maybe it´s a simple thing, so simple that i´m to stupid to see that.. Sorry for my bad inglish but i write lot of erros even in my language. Any help will be very welcome. Tanks for ur concern and atention ^^

    Read the article

  • Windows 7 installation: drive selection doesn't show drive letter

    - by FrozenKing
    I am eager to get this answer i.e. in Windows 7 when we format the computer there is a problem that when we have to select drive for formatting, it doesn't show drive letter. *I need a solution wherein when I format I want to know its drive letter so that I may not be confused while formatting. *See the difference between windows xp and windows 7. I want windows 7 to show drive letters like windows xp. Does any one know why windows 7 doesn't show drive letters.

    Read the article

  • Nexus One USB freezes Vista SP2 Quad Core

    - by user25479
    My Nexus One (N1) will occasionally freeze my Vista 32bit SP2 Quad Core 2.4GHz during POST. MB is ASUS P5N-E SLI with 4GB of RAM. The PC will be booting and when I connect the N1 via USB, the boot sequence will freeze, then continue once I unplug the N1 USB link. It happens whether the N1 is in USB debugging mode and when it is not. I'm not sure whether this is an N1 hw/fw issue, system interaction with my PC, or a result of my N1 development environment (I'm using the Eclipse Galileo IDE for Java Developers, primarily compiling to API Level 7. Eclipse has also occasionally frozen although I haven't established N1 USB cause-and-effect on that issue). Is anyone else experiencing these symptom?

    Read the article

  • Using Virtualbox USB capabilities

    - by Eder Gusatto
    Is there anyone actually using the USB capabilities of the Virtualbox? I've tried in 3 diferent computers and just keep receiving the message that the USB device is busy with a previous request. I'm trying to access USB stuff since the first version (now using 3.0.4) but I was never successful. Is there any special configuration or tweak to make?

    Read the article

  • None of usb-controllers are working after a crash

    - by Cray
    So I have a GA-p35-DS4 mboard with a Q6600, running windows7-x64. After a random crash with a bluescreen (not caused by anything particular as I recall), none of the usb-controllers are working. (And none of the devices connected to those usb ports). All the controllers are showed up in the device manager, but every one has a warning-icon (as they are not functioning properly). The windows identifies them correctly, it shows exactly the model of each controller, and it says that the driver is installed. Now, when I try to reinstall the driver (Update driver menu item in the device manager), it tries to find it, finds the driver, but quits saying that the driver was found but could not be installed. Additionally, it displays "This operation requires an interactive window station", whatever that means... Now get this, the same thing happens with a new pci-usb controller card! It is found (actually each time the machine starts, it is found as new hardware), but trying to install drivers leads nowhere, I am getting the same message about an interactive window station. (tried to install drivers from the acoompanying CD) I have tried deleting those devices from device manager and let windows find them again, but that leads to same results. None of the ports on this extension card work either. This should not be a hardware problem, a usb keyboard connected to the builtin usb controller works in bios, and even in another OS running the same computer (old xp installation) What to do? Will I have to reinstall? Can deleting infcache.1 help? Is there some way to let windows remove all old drivers and try to find all hardware again, this time only looking for drivers on a windows install disk or something?

    Read the article

  • Short USB cables not charging?

    - by tropolite
    I find this a strange problem but I can't find anything online about it. Recently I purchased a few short USB cables (20-30cm), to use in my car's USB connector to charge my phone. Strangely an older longer USB cable (1.2m), charges the phone fine (and the icon changes to show charging). With any of the short cables in the same USB slot no charging happens. Both the long and the short cables are USB2 compatible. I naturally assumed the short cables were faulty but connecting them to a PC or connecting to a high capacity external battery charging is successful using all the short cables and longer cables. Hopefully someone here is able to give me an explanation of the problem and how I can overcome this and use a short cable where it is most appropriate. Thanks

    Read the article

  • Kickstart based installation of RHEL 6.4 from USB

    - by Peter
    I want to setup some brand new servers with RHEL 6.4. Servers do not have DVD, so, I have to use USB for the installation. I already have a custom ISO with a kickstart file that I use on servers with DVD flawlessly. I used iso2usb to move the ISO t? my USB. When I boot from the USB, the ks file is found, anaconda starts, but then stops with the following error: "The installation source given by device ['sda1'] could not be found. Please check your parameters and try again" Notes: The USB IS the sda. My custom ISO file is renamed to linux.iso from iso2usb and it is present in the root directory of the USB. Kickstart file has the following entry: harddrive --partition=sda1 --dir=/ Please help me to automate the installation with kickstart. Edit 1: This the anaconda.log file: 09:01:57,029 INFO : no /etc/zfcp.conf; not configuring zfcp 09:01:57,259 INFO : created new libuser.conf at /tmp/libuser.4rAbps with instPath="/mnt/sysimage" 09:01:57,259 INFO : anaconda called with cmdline = ['/usr/bin/anaconda', '--stage2', 'hd:sda1:///images/install.img', '--dlabel', '--kickstart', '/tmp/ks.cfg', '--graphical', '--selinux', '--lang', 'en_US.UTF-8', '--keymap', 'us', '--repo', 'hd:sda1:/'] 09:01:57,260 INFO : Display mode = g 09:01:57,260 INFO : Default encoding = utf-8 09:01:59,444 DEBUG : X server has signalled a successful start. 09:01:59,446 INFO : Starting window manager, pid 1345. 09:01:59,537 INFO : Starting graphical installation. 09:01:59,741 INFO : Detected 7968M of memory 09:01:59,741 INFO : Swap attempt of 7968M 09:02:00,840 INFO : ISCSID is /usr/sbin/iscsid 09:02:00,840 INFO : no initiator set Edit 2: This is the part of anaconda log that indicates that it found the USB etc: 09:01:47,918 INFO : starting STEP_STAGE2 09:01:47,918 INFO : partition is sda1, dir is //images/install.img 09:01:47,918 INFO : mounting device sda1 for hard drive install 09:01:48,005 INFO : Path to stage2 image is /mnt/isodir///images/install.img 09:01:54,214 INFO : mounted loopback device /mnt/runtime on /dev/loop0 as /tmp/install.img 09:01:54,214 INFO : Looking for updates for HD in /mnt/isodir///images/updates.img 09:01:54,214 INFO : Looking for product for HD in /mnt/isodir///images/product.img 09:01:54,227 INFO : got stage2 at url hd:sda1:///images/install.img 09:01:54,254 INFO : Loading SELinux policy 09:01:54,700 INFO : getting ready to spawn shell now 09:01:54,975 INFO : Running anaconda script /usr/bin/anaconda 09:01:56,882 INFO : _Fedora is the highest priority installclass, using it 09:01:56,921 INFO : Running kickstart %%pre script(s) 09:01:56,922 WARNING : '/bin/sh' specified as full path 09:01:56,926 INFO : All kickstart %%pre script(s) have been run

    Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >