Search Results

Search found 3141 results on 126 pages for 'zero'.

Page 53/126 | < Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >

• Single-port 2600 router with 2900XL switch

  - by Slava Maslennikov

  I have a setup, where the single port 2600 router is in port 0/2 in the switch, outside network is on port 0/1, and the rest (0/3-0/24) should be clients for the second network that would be managed by the 2600 router. I configured everything with two VLANs: 100 for outside (0/2-0/24), 200 for inside (0/1-0/2). 0/2 is a trunk port for the two VLANs. The issue that came about is that I can't have two VLANs on at once: software doesn't allow it. Now, I can ping the outside network devices (172.16.7.1, 172.16.7.103), and even google (8.8.8.8) from the router, but not the switch. Devices on connected get a DHCP lease properly but can't ping outside the network, just the router - 172.17.7.1 and the switch itself, 172.17.7.7. The configuration for both the router and the switch are here, as well as below. Router: rt.throom#sho run Building configuration... Current configuration : 1015 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname rt.throom ! enable password To053cret ! ! ! ! ! no ip subnet-zero ip dhcp excluded-address 172.17.7.1 172.17.7.2 ip dhcp excluded-address 172.17.7.3 172.17.7.4 ip dhcp excluded-address 172.17.7.5 ! ip dhcp pool VLAN200 network 172.17.7.0 255.255.255.0 default-router 172.17.7.1 dns-server 8.8.8.8 ! ip audit notify log ip audit po max-events 100 ! ! ! ! ! ! ! interface Ethernet0/0 no ip address ! interface Ethernet0/0.100 encapsulation dot1Q 100 ip address 172.16.7.15 255.255.255.0 ip nat outside ! interface Ethernet0/0.200 encapsulation dot1Q 200 ip address 172.17.7.1 255.255.255.0 ip nat inside ! router eigrp 20 network 172.16.0.0 network 172.17.0.0 no auto-summary no eigrp log-neighbor-changes ! no ip classless no ip http server ! access-list 1 permit 172.17.7.0 0.0.0.255 ! ! line con 0 line aux 0 line vty 0 4 login ! end Switch: sw.throom#sho run Building configuration... Current configuration: ! version 11.2 no service pad no service udp-small-servers no service tcp-small-servers ! hostname sw.throom ! enable password Oh5053cret ! ! no spanning-tree vlan 100 no spanning-tree vlan 200 ip subnet-zero ! ! interface VLAN1 no ip address no ip route-cache ! interface FastEthernet0/1 switchport access vlan 100 spanning-tree portfast ! interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk ! interface FastEthernet0/3 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/4 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/5 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/6 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/7 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/8 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/9 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/10 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/11 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/12 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/13 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/14 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/15 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/16 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/17 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/18 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/19 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/20 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/21 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/22 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/23 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/24 switchport access vlan 200 spanning-tree portfast ! ! line con 0 stopbits 1 line vty 0 4 login line vty 5 9 login ! end sho ip route gives: Gateway of last resort is 172.16.7.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.7.0 is directly connected, Ethernet0/0.200 172.16.0.0/24 is subnetted, 1 subnets C 172.16.7.0 is directly connected, Ethernet0/0.100 S* 0.0.0.0/0 [1/0] via 172.16.7.1

  Read the article

• How to redirect the output of the vmrun listProcessesInGuest command on windows?

  - by mark

  I run vmrun.exe with listProcessesInGuest on the command line and get the list of processes displayed in the console window. The exact command line is: "C:\VIX\vmrun.exe" -T vc -h "https://myserver/sdk" -u "mydomain\myuser" -p 123 -gu Administrator -gp 123 listProcessesInGuest "[Storage1] QA-W-7-SP1-64-0/QA-W-7-SP1-64-0.vmx" It works fine. Now I wish to redirect the output, however, neither 2> nor 1> work! The former has no effect - the output is still displayed in the console window, so I conclude it is send to stdout. But the latter does not work too - now nothing is displayed in the console window, but the redirection file is empty! It is created all right, but it has the zero size! Can someone explain what is going on?

  Read the article

• Not Able To Connect to Shared Resource

  - by bobber205

  We are using an older version of BartPE and are not able to connect to shared folders on our subnet. It says the network name could not be found. Connecting to the shared folder on the machine that is hosting it works fine. Any ideas on what might cause this? Thanks! Edit1: Got wireshark running and monitored traffic from the offending machine and tried to map. ZERO packets from the other machine were seen. :(

  Read the article

• Getting ROBOCOPY to return a "proper" exit code?

  - by Lasse V. Karlsen

  Is it possible to ask ROBOCOPY to exit with an exit code that indicates success or failure? I am using ROBOCOPY as part of my TeamCity build configurations, and having to add a step to just silence the exit code from ROBOCOPY seems silly to me. Basically, I have added this: EXIT /B 0 to the script that is being run. However, this of course masks any real problems that ROBOCOPY would return. Basically, I would like to have exit codes of 0 for SUCCESS and non-zero for FAILURE instead of the bit-mask that ROBOCOPY returns now. Or, if I can't have that, is there a simple sequence of batch commands that would translate the bit-mask of ROBOCOPY to a similar value?

  Read the article

• Unexpected behavior in Bash

  - by cYrus

  From man bash: A simple command is a sequence of optional variable assignments followed by blank-separated words and redirections, and terminated by a control operator. The first word specifies the command to be executed, and is passed as argument zero. The remaining words are passed as arguments to the invoked command. So it's perfectly legal to write: foo=bar echo $foo but it doesn't work as I expect (it prints just a newline). It's quite strange to me since: $ foo=bar printenv foo=bar TERM=rxvt-unicode [...] Could someone please explain me where I'm doing wrong?

  Read the article

• Adding GLUE records for Google Apps MX records

  - by Saif Bechan

  Is there a way of adding GLUE for the Google Apps MX records. I have added them all and it works fine, but in all the DNS tools I see that there is no glue sent. I know that this is not a really big problem, because the gain you get out of it is next to zero. Nevertheless I just wanted to know if it is possible and how you do it. Or if it is not possible, what is the reason for it. I have asked this question also on the Google Help Forum but with no responses so far, so I thought i'd give it a shot here.

  Read the article

• One network, two macbooks, one is fast and the other is slow

  - by Brendan

  I really need help for my friend. I know next to nothing about computers. My roommate and I both have macbook pros from the same year running OS X, are both connecting wirelessly to the same xfinity wifi, and while mine runs perfectly fine, my roommate complains that his works very slowly and times out every few seconds. I can't seem to figure out why this is. He is trying to get me to switch internet providers because he is convinced that it is their problem, but this cannot possibly be the issue since it works great on mine. He has an xbox hooked up to the wifi that he says also works poorly. I really can't see switching providers given that I am experiencing absolutely zero problems. How can I help my friend?

  Read the article

• unable to re-attach screen session on freebsd

  - by Michael

  I have a screen session that I am unable to re-attach to. I have tried kill -CHLD 6859, with zero success. Is there anything else that I can try to get this session re-attached q4# screen -ls No Sockets found in /tmp/screens/S-root. q4# ls -la /tmp/screens/S-root/ total 8 drwx------ 2 root wheel 512 May 26 12:52 . drwxr-xr-x 4 root wheel 512 Feb 26 2013 .. prwx------ 1 root wheel 0 May 26 10:14 6859.pts-0.q4 q4# ps uax 6859 USER PID %CPU %MEM VSZ RSS TT STAT STARTED TIME COMMAND root 6859 0.0 1.2 84732 50444 ?? Ss 2Jan13 34:06.71 screen -h 9999 q4# screen -r There is no screen to be resumed. q4# whoami root q4#

  Read the article

• SNMP - Value of CPU processor load not reflecting reality

  - by Ovesh

  Trying to plot CPU load on my server, with the following hardware: ProLiant DL360p Gen8 (same behavior on ProLiant DL360 G7). The machine is running VMWare ESXi5.1 To create a CPU spike I run dd if=/dev/zero of=/dev/null, and I know the CPU is overloaded, because I can see a correlating spike in the graphs displayed on vCenter. However, running this snmpwalk: snmpwalk -v 1 -c ******** 192.168.MY_IP 1.3.6.1.2.1.25.3.3.1.2 Shows the following results: iso.3.6.1.2.1.25.3.3.1.2.1 = INTEGER: 3 iso.3.6.1.2.1.25.3.3.1.2.2 = INTEGER: 2 iso.3.6.1.2.1.25.3.3.1.2.3 = INTEGER: 2 iso.3.6.1.2.1.25.3.3.1.2.4 = INTEGER: 3 Am I not looking into the right MIB? Should I be multiplying these by a constant? By the way, using HP Agentless Monitoring I was able to get some cpu stats, but not what I'm looking for, at least nothing I could find wading through these MIBs.

  Read the article

• Why does a pdf file download result in varying bytes logged, all with sc-status 200

  - by Pat James

  I have a mojoportal CMS installation on an IIS7 server where users are reporting problems downloading a pdf file. It always downloads fine for me and most others, either displaying in browser or in Adobe Reader. Using logparser to query the IIS logs, all the responses are status 200 (OK) or 304 (Not modified), but the bytes sent vary quite a bit. Sometimes zero, some 211, some about half the full file size of 27059, and lots in between. Plenty show the full size of 27059. Do these other entries for smaller byte counts represent errors of some kind, correlating with the problems reported? Is this likely to be a browser/client issue or a server side problem? If there is any other info that would be helpful let me know. This is a shared hosting server though so I am somewhat limited in what I can dig into on the server.

  Read the article

• Moving from Analogue PBX to digital VoIP?

  - by saint

  I don't even know if this belongs here?. If not, do let me know. So we have an analogue Alkatel PABX system in our little office. We have extensions, direct lines and PBX lines. We are trying to move to a more digital/flexible way of handling the phones and I've heard good things about FreeSwitch. I have zero knowledge about it. My biggest question is how would one handle existing phone lines with such a system. Surely there must be a way to make and receive calls from outside. Just a help in the right direction would be fine. Thanks.

  Read the article

• In Visio 2010, how can I create a mandatory, non-identifying relationship between two database tables

  - by Cam Jackson

  I'm working in MS Visio 2010. This is the relevant part of my ERD: The relationship between Event and Adventure is correct: there's a foreign key from Event to Adventure, and that FK is part of Event's primary key. However, what I can't figure out is how to make the relationship line from Adventure to AccomodationType be the same, without making that relationship part of the PK of adventure. When I look at the 'Miscellaneous' properties of that relationship line, I want it to be: Cardinality: Zero or more Relationship type: Non-identifying Child has parent: Not optional (mandatory) But the checkbox for the third property is greyed out, and toggles between True/False as I make the relationship Non-identifying/Identifying. The only way I could figure out was to disconnect the two columns, from the 'Definition' tab, which then un-grey's the 'Optional' checkbox, but then I lose the foreign key property on the accomType column, and while the relationship symbols are correct, the line remains dotted. Any ideas, anyone?

  Read the article

• Throughput = BS * IOPS?

  - by Marvin

  I've seen in many places that throughput = bs * iops should be true. For example writing at 128k block size to a SAS disk that can support 190 IOPS should give a throughput of ~23 MBps - 23.75(MBs) = 128(BS)*190(SAS-15 IOPS)/1024. Now when I tested it in a VM against a monster NetApp filer I got theses results: # dd if=/dev/zero of=/tmp/dd.out bs=4k count=2097152 8589934592 bytes (8.6 GB) copied, 61.5996 seconds, 139 MB/s To view the IO rate of the VM I used iostat and esxtop, and they both showed around 250 IOPS. So to my understanding the throughput was supposed to be ~1000k: 1000(KBs) = 4(BS)*250(IOPS). dd of 8GB is twice the size of RAM of course, so no page caching here. What am I missing? Thanks!

  Read the article

• help with Outlook Exchange server and curl

  - by stib

  I work on a mac in a building full of PCs, and the IT department here doesn't have IMAP access turned on on the exchange servers. So I miss a lot of meetings because I don't get reminders because I access my mail via Outlook Web access. I had written a script to scrape my Outlook Web Access calendar and turn it into iCal format, so I could get my reminders via thunderbird or iCal.app. It basically downloaded the calendar page via curl, parsed the HTML and reformatted all the appointments as ical. it wasn't elegant, but it worked. Then they changed to outlook 2007, and it doesn't work any more. I have a sketchy knowledge of curl, and almost zero knowledge of how outlook works. Can anyone point me towards a reference for getting calendar info out of an exchange server without using outlook? If I can configure curl to get the HTML I will be happy, but if there's a more elegant way, such as getting the calendar info as XML I'll be delirious.

  Read the article

• How to deploy SQL Server 2005 Reporting Services on a network without a domain server?

  - by ti

  I have a small Windows network (~30 machines) and I need to deploy SQL Server 2005 Reporting Services. Because I use SQL Server Standard Edition and not Enterprise, I am forced to use Windows Authentication to the users. I am a Linux admin, and have near zero knowledge on Active Directory. As deep as my shallow knowledge goes, I think that I would need to invest in a domain server, a mirrored backup of that domain server. I think that I need to change every computer to use this domain too, and if the domain server goes down, every computer will be unavailable. Is there a easier way to deploy Windows Authentication so that users can access Reporting Services from their computers without changing the infra-structure that much? Thanks!

  Read the article

• rsyslog from Heroku drain creates empty log files

  - by Jeff Lee

  I'm sending logs from my Heroku app to an rsyslog server, but the resulting log files seem to come up empty. The rsyslog configuration for receiving remote messages is as follows: $template RemoteDailyLog,"/var/log/remote/%hostname%/%$year%/%$month%/%$day%.log" :fromhost-ip, !isequal, "127.0.0.1" -?RemoteDailyLog & ~ My complete rsyslog configuration is available in this paste. This configuration appears to create the directories correctly. I see the Heroku app's logging hostname (of the form "d.xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx") appear in /var/log on the rsyslog host, which implies that log messages are successfully making it to the logging daemon, but the resulting logfiles are zero-size. I'm guessing the issue is with rsyslog, rather than Heroku, but I'm not sure where to look next.

  Read the article

• Active Directory: how do you pull a list of accounts that belong to a user?

  - by Jack

  I'm a software developer currently stuck to support CyberArk at a large company. I need to pull up a list of accounts that is belong to a certain user. For example, let's said I have a user account named Bob and I want to find all the accounts that belong to Bob in AD meaning on the Organization tab of a user properties, the Manager should be Bob. I've absolutely zero knowledge regarding AD except the very basic. Is there a way to do it? I only have access to "Active Directory Users and Computers" tool and I'm not even sure if I have enough privilege to run script or install powershell to do it but would like to know the script or powershell command to do so if there is one.

  Read the article

• Storing large amounts of small files into bigger files on Windows

  - by asmo

  Let's say I have 50 GiB of files that weights around 500 KiB each. My guess is that having, for example, 5 large files of 10 GiB each with the same content archived in them would be better for hard drive performance. Am I correct? Will there be a noticeable gain on an NTFS filesystem? ===================================================================== Finally, which tool could I use to group the files together while retaining the ability to modify the content of the archive with zero or minor performance loss? For example, I like TrueCrypt archiving because after mounting an archive file, it creates a drive which I can use seamlessly as if it was a normal drive. The only thing with TrueCrypt is that I don't need encryption/compression, only archiving.

  Read the article

• My HP-Vista based laptop has become very slow recently

  - by goldenmean

  My HP laptop which has Vista Home premium. When I try to start Firefox, internet explorer, it becomes very slow. No other app. When i checked the Performance in Task Manager. It shows the Physical memory , Free as 0 bytes, almost always. This has been recently. Earlier it didn't used to be zero. Laptop has 2GB of RAM. I have nothing running in my tray except - Sound control, Laptop power plan indicator,Network status indicator. There are no other processes whose memory usage adds up to so high to make Free memory as 0. Then what could be hogging the memory and make the laptop very slow. Any pointers would help as it is crawling at the moment.

  Read the article

• Apache Serving 403 Forbidden after OS X Snow Leopard Upgrade to Version 10.6.6

  - by Ian Oxley

  I've just upgraded my MacBook Pro to OS X Snow Leopard version 10.6.6 and now Apache is misbehaving: requests to http://localhost/ generate a 403 Forbidden response -- FIXED requests to any of my virtual hosts seem to generate a 200 Ok response, but contain zero bytes Some further info that might be useful: I'm using the Apache that comes bundled with OS X. I'm using PHP from http://www.entropy.ch/software/macosx/php/ (which is in /usr/local/bin) I've had look at the Apache error log and the only error seems to be the following: [notice] child pid 744 exit signal Segmentation fault (11) I'm completely stumped by this. Any help would be much appreciated. UPDATE Ok, I've managed to resolve the 403 Forbidden error thanks to http://techtrouts.com/mac-os-x-105-web-sharing-forbidden-403-on-httplocalhostusername/ I'm still having the second problem though for any request e.g. this now happens when I request http://localhost

  Read the article

• Windows 7 Locking up Randomly

  - by Michael Moore

  I've got a Windows 7 machine that is locking up randomly. It can be in the first thirty seconds, or it can be hours later. There is nothing specific I can find that is running when it happens. When it locks, the screen doesn't change, but nothing moves. The waiting icon stops, the mouse stops, keyboard doesn't work, etc. I've even tried the crash on ctrl-scrl registry hack, and it won't even dump the kernel. I've run hardware diagnostics on the RAM and it doesn't find any problems. I would think it is a hardware issue, but on this exact same machine, I can run 64 Bit Ubuntu and it has zero problems. I've even tried reinstalling Windows7 from scratch, and it still happens. Anyone have any ideas? Any good diagnostic tools to recommend? Thanks! Michael

  Read the article

• IIS site hacked with ww.robint.us malware

  - by sucuri

  A bunch of IIS sites got hacked with a javascript malware pointing to ww.robint.us/u.js. Google cache says more than 1,000,000 different pages got affected: http://www.google.com/#hl=en&source=hp&q=http%3A%2F%2Fww.robint.us%2Fu.js http://blog.sucuri.net/2010/06/mass-infection-of-iisasp-sites-robint-us.html My question is: Did anyone here got hacked with that and still have any logs (or network dump) available for analysis? If you do, have you spotted anything interesting in there? Sites as big as wsj.com got hacked and some people are saying that maybe a zero-day on IIS/ASP.net is in the wild...

  Read the article

• Driver problems with rerunning WIM capture

  - by Tim Brigham

  How do I handle driver problems associated with creating a new WIM file using a previously created image as a base? I am using a custom MDT image which installs Windows 7, Office 2010, etc which was created from a previously deployed base image of Windows 7 + SP 1 + updates. When the driver injection is enabled I receive a group of messages (collected from different logs, screens, etc). If I turn the preinstall driver injection off things work as expected. If I leave it on I receive the following messages. windows cannot install required files 0x80004005 8004004 non zero return code ltiapply rc=31 Unhandled error returned by LTIApply: a device attached to the system is not functioning. (-2147024865 0x8007001F)

  Read the article

• VMware Workstation on Linux: Dropping core files in a shared folder...

  - by kclittle

  I'm using VMware 6.0.2 on a RHEL 4.6 host. The VMs are MontaVista CGE 5.0 (2.6.21 kernel). I'm trying to get applications running in the VMs to drop any core files on a HGFS volume, i.e. in a "shared folder". The core files get created as per the path and format given in /proc/sys/kernel/core_pattern, but they are always zero length. If I change the path to a local path (on a virtual disk in the VM), all is well. Any ideas what I have to do get the core files written into a shared folder? Thanks for your help!

  Read the article

• Cisco, How to do a subnetting scheme using VLSM and RIP-2?

  - by Andrei T. Ursan

  I'm studying for my CCNA exam and I have to create a VLSM scheme using RIP-2 for the following requirements: (this is an exercise) Use the class C network 192.168.1.0 network for your point-to-point connections Using the Class A network 10.0.0.0, plan for the following number of hosts in each location: New York: 1000 Chicago: 500 Los Angeles: 1000 On the LAN and point-to-point connections, select subnet masks that use the smallest ranges of IP addresses possible given the above requirements. In all cases, use the lowest possible subnet numbers. Subnet zero is allowed. My guess is the following: New York: S0/0 192.168.1.1 /24 Fa0/0 10.1.0.1 netmask 255.255.248.0 - because we need 1000 hosts Chicago: S0/0 192.168.1.2 /24 Fa0/0 10.2.0.1 netmask 255.255.252.0 (for 500 hosts) Los Angeles: S0/0 192.168.2.3 /24 Fa0/0 10.3.0.1 netmask 255.255.248.0 (for 1000 hosts) Is this a good configuration? I'm reading the CCNA book but not everything is very clear, so I said to do some exercises... Thank you!

  Read the article

< Previous Page | 49 50 51 52 53 54 55 56 57 58 59 60  | Next Page >