Search Results

Search found 18126 results on 726 pages for 'core pro'.

Page 539/726 | < Previous Page | 535 536 537 538 539 540 541 542 543 544 545 546  | Next Page >

• How do you passthrough native SATA drives to a guest on ESXi?

  - by John

  I have ESXi 4.0 running on an Intel DX58S0 Mothboardboard with an Intel Core i7 930 processor. VT-d is also enabled. I have three drives in the system, drive 0 is used for ESXi. Drive 1 and 2 contain data from an older machine and show up under the "Storage Adapters" section in configuration. I would like to allow a guest machine to access the data on these drives (as nativly as possible). I have enabled passthrough of the motherboard's built in SATA controller (Intel/Marvell 88SE6121 ). This controller shows up in my guest OS, but the guest shows no drives aside from the normal virtual drive. I have tried a Linux guest and Windows7. I have also configured the host machine to try IDE/RAID/ACHI modes for the SATA controller. Any ideas how I can configure one of my guests to get at the raw data on these drives?

  Read the article

• How to understand cpu family/model/stepping fields in /proc/cpuinfo [closed]

  - by Victor Sorokin

  I have following in cpuinfo: processor : 0 vendor_id : AuthenticAMD cpu family : 15 model : 107 model name : AMD Athlon(tm) 64 X2 Dual Core Processor 5600+ stepping : 2 According to Wikipedia page there are two kinds of 5600+ -- one of 90nm technology, another of 65nm. How can I understand which one I have? There seem to be no direct correspondence between contents of cpuinfo and info on Wikipedia page. AMD site seems to use some other naming scheme for processors too. How can I map values of family, model and stepping from cpuinfo to the data available on Wikipedia/AMD?

  Read the article

• Windows RRAS multi-network routing

  - by Brent Pabst

  I am looking for advice, comments and suggestions from anyone who has used Windows RRAS (2008 R2 Pref.) as the primary routers for our multiple offices. We have multiple physical office locations and are looking into utilizing Windows Server 2008 R2 Core as redundant Active/Active routers/gateways for our network as opposed to a physical router from Cisco or Juniper, it costs a lot less! Any problems, issues or documentation anyone would recommend? We will still most likely have a firewall on the edge but the majority of our traffic will be inter-office with some external services. We will be using multiple Class B networks across our two offices.

  Read the article

• Windows 2012 - WDS unattend Partition

  - by joe

  I'm trying to install Windows 2012 via Windows 2012 WDS. The installer displays the following error message: the partition selected for the installation (1) does not exist on disk 0. Make sure the unattend answer file's imageselection \installimage setting references a valid partition on this computer, and then restart the installation. the unattend file (created by the "Create Client Unattend" dialog) <unattend xmlns="urn:schemas-microsoft-com:unattend"> <settings pass="windowsPE"> <component name="Microsoft-Windows-Setup" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" processorArchitecture="x86"> <WindowsDeploymentServices> <Login> <WillShowUI>OnError</WillShowUI> <Credentials> <Username>administrator</Username> <Domain>test</Domain> <Password>xxxx</Password> </Credentials> </Login> <WillWipeDisk>true</WillWipeDisk> <DiskConfiguration> <WillShowUI>OnError</WillShowUI> <Disk> <DiskID>0</DiskID> <WillWipeDisk>true</WillWipeDisk> <CreatePartitions> <CreatePartition> <Order>1</Order> <Type>Primary</Type> <Extend>true</Extend> </CreatePartition> </CreatePartitions> </Disk> </DiskConfiguration> <ImageSelection> <WillShowUI>OnError</WillShowUI> <InstallImage> <ImageGroup>ImageGroup1</ImageGroup> <ImageName>Windows Server 2012 SERVERDATACENTER</ImageName> <Filename>install-(4).wim</Filename> </InstallImage> <InstallTo> <DiskID>0</DiskID> <PartitionID>1</PartitionID> </InstallTo> </ImageSelection> </WindowsDeploymentServices> </component> <component name="Microsoft-Windows-International-Core-WinPE" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" processorArchitecture="x86"> <SetupUILanguage> <UILanguage>en-US</UILanguage> </SetupUILanguage> <InputLocale>en-US</InputLocale> <SystemLocale>en-US</SystemLocale> <UILanguage>en-US</UILanguage> <UserLocale>en-US</UserLocale> </component> <component name="Microsoft-Windows-Setup" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" processorArchitecture="amd64"> <WindowsDeploymentServices> <Login> <WillShowUI>OnError</WillShowUI> <Credentials> <Username>administrator</Username> <Domain>test</Domain> <Password>xxxxx</Password> </Credentials> </Login> <ImageSelection> <WillShowUI>OnError</WillShowUI> <InstallImage> <ImageGroup>ImageGroup1</ImageGroup> <ImageName>Windows Server 2012 SERVERDATACENTER</ImageName> <Filename>install-(4).wim</Filename> </InstallImage> <InstallTo> <DiskID>0</DiskID> <PartitionID>1</PartitionID> </InstallTo> </ImageSelection> </WindowsDeploymentServices> </component> <component name="Microsoft-Windows-International-Core-WinPE" publicKeyToken="31bf3856ad364e35" language="neutral" versionScope="nonSxS" processorArchitecture="amd64"> <SetupUILanguage> <UILanguage>en-US</UILanguage> </SetupUILanguage> <InputLocale>en-US</InputLocale> <SystemLocale>en-US</SystemLocale> <UILanguage>en-US</UILanguage> <UserLocale>en-US</UserLocale> </component> </settings> </unattend> Any idea why it is not working? thanks

  Read the article

• Xnest from Mac OSX to HP UX

  - by Burbas

  Hi, I'm trying to connect to my HP/UX machine from Mac OS X using Xnest. The problem is that I can not get the keyboard to work. I can see the login-prompt, but unable to type in my username. The connection is done by: Xnest :1 -query 192.168.0.193 -geometry 1280x1024 and it gives me some errors: (EE) AIGLX error: dlopen of /usr/X11/lib/dri/swrast_dri.so failed (dlopen(/usr/X11/lib/dri/swrast_dri.so, 5): image not found) (EE) GLX: could not load software renderer (EE) XKB: Couldn't open rules file /usr/X11/share/X11/xkb/rules/base (EE) XKB: No components provided for device Virtual core keyboard Couldn't get keyboard. I hope there is someone here who might have the answer :-).

  Read the article

• Facing gestures in Linux mint Chrome Browser

  - by aravind.udayashankara

  I am using Linux mint OS since an Year , I use to consistently download updates and install , I use chrome as a default browser , when ever I open youtube and watch some video , I listen to some gestures in sound ( say repeated lyrics of song ) while it is playing , In firefox it is working fine . What is the problem am I missing any plugin , AFAIK Chrome doesn't need a flash player plug in , It has a built in flash player . IS that the problem ? And also previously I was not facing this , recently I started using Cinimon UI centOS after this all these kind of problems started MY hard ware is 64 bit intel core i3 and also I have installed linux mint 64 bit Please let me know what is the problem and how to fix this . Thanks in advance for responding to this post

  Read the article

• How to limit my CPU power programmatically on Windows 7?

  - by Ivan

  Whenever I run a CPU-heavy activity (like compressing a big set of files into an archive for example) my CPU switches to its full throttle (maximum frequency) and shuts down of overheat in less than a minute. Instead, I would like it to keep slowed-down slightly to do the task a bit slower but be able to reach the finish. At the same time I don't want to dim my screen brightness or adjust anything else what standard Windows power-saving system does. So how do I actually set a cap to limit my CPU power? The CPU is Core 2 Duo T7250, the OS is Windows 7 32-bit, there seem to be no BIOS settings or jumpers available to configure the frequencies.

  Read the article

• Another "Trouble copying music files from HD to 16GB thumb drive"

  - by Ron

  I have a brand new HP Quad Core - 6GB Ram - running 64-bit Windows 7. Running Norton Internet 2010. I try copying music files from HD to 16 GB thumbdrive and get blue screen after a few files have transfered over to thumbdrive. Computer blinks once and boom - blue screen and then reboots. This is really aggravating. I stopped anti-virus, pulled other USB attached devices - still does same thing. Any solutions out there?

  Read the article

• safari 5 doesnt work on my computer.

  - by Amairani409

  I just got the new version of safari y downloaded because my mac tell me there was new version that I should be getting. but when I try to run my this new version of the aplication .nothing happends¡ I mean the program seems to be working but nothing apears in the screen and so when I try to see my top sites a little window show up but it just dont show anything. then 3 seconds later the program shut down¡ I dont know why is happening this Im not so a expert in computers but this really is away of all I see on safari and on mac I got Mac OS X version 10.5.8 2.66ghz intel core 2 duo 4gb 1067 MHz DDR3

  Read the article

• USB Hub powers down in sleep mode on Win 7 64

  - by Andy B

  This question has been asked before but not answered. I would like the USB hub to remain on in sleep so I can wake up the laptop from an external keyboard and mouse. I have set all the device drivers by unchecking allow this device to be powered down and disabled selective suspend in control panel but the hub still powers down. If I plug a keyboard or mouse directly in to the PC they remain powered and wake the computer its only when they are connected through the hub there is a problem. I have another PC running Win 7 32. If I set this up in exactly the same way the hub remains powered in sleep. Both PC's are Toshiba Satellites with multi-core celerons but one runs Win 7 32 the other Win 7 64. BIOS settings are the same. Any help would be appreciated even confirmation that this is a feature of Win 7 64.

  Read the article

• JAVA vs .NET Technology - Way 2 go Futher

  - by Sarang

  I have my subject .net acedemically. I also learned core-java and did a project as well. I took training from a java firm. Now, as a skill I do have knowledge as both language. But, it is creating a large problem to me that, which field I should chhose? Even if having better OOP funda, will it be easier for me to transfer from one-another in future ? Please suggest me a way. Also, we do have may technologies available at both side, like JSP, JSF, J2ME, Share Point, SilverLight etc. Which is better as per their reliabity point of view? Which are fast growing and useful technologies used mostly in current IT corporate world ? Are they easier to learn at fresher's point of view? Please answer. Perhaps, this answer may help me mostly to create my way to learn them and go further.

  Read the article

• Testing a Virtualisation of a Debian Server (vmWare vSphere probably)

  - by xyza

  I'm soon getting access to a powerful root-server (quad-core, 16gb ram, 1gbit connection) where gameservers (like minecraft,counterstrike etc.) for different customers should be setup. My plan is to use programs such as vmWare vSphere to create some virtual machines for each customer. Inside such a virtual machine I'll setup the gameserver and maybe some kind of ftp server when its needed. Now that I'm kinda new to virtualisation of servers I want to test this local on my Desktop Computer. Is it possible to create a virtual machine of debian using vmWare Player on my Windows desktop computer and then install vmware vSphere in this VM to create multiple VM's inside that VM ? Or do I really need to install Debian on my desktop computer. (I want to use the time during installations etc. to work a bit at my windows installation) Some tips on virtualising debian servers are also appreciated :)

  Read the article

• Why does my CPU Usage reach 100% too often?

  - by deathlock

  I'm using a dual-core processor and often see my CPU usage reaches 100%. I realize this may happen if I'm running too much applications, so when I know the computer starts to run slowly, I start to close my applications. I usually run 4-5 applications simultaneously. Usually those are: web browser (Google Chrome), Adobe Photoshop, Notepad++, XAMPP, and Windows Task Manager. Usually I close tabs in my Chrome first, because I often browse the net with about 20 tabs/4 windows open, so I presume that would take much memory (bad habit, I know). But even after closing Chrome's tabs or closing other applications, my CPU Usage often stays at high percentage - 72% at best, 100% at worst. I check the Processes tab on Windows Task Manager and usually found the System, System Idle Process, or services.exe taking the highest CPU process (could reach 60). Why is this happening? And is there any solution? EDIT I have T2250 @ 1,73 Ghz and 2.5 GB RAM

  Read the article

• Will this RAM work well in an iMac?

  - by sala_7

  I want to increase the RAM of my 2.4GHz Intel Core 2 Duo 24" iMac. I currently have 1GB of RAM DDR2 SDRAM 667 MHz. I really want to upgrade, but know nothing about RAM or hardware in general... These are the cards I found: http://www.crucial.com/eu/store/mpartspecs.aspx?mtbpoid=D4B6F603A5CA7304 Are these of quality or should I look at something else? Finally, I have 800MHz of Bus speed, couldn't I get faster RAM? Thanks for taking the time to read, and hoping you take the time to answer.

  Read the article

• Bad HD video deinterlacing processing

  - by Guy Fawkes

  I have Ubuntu 12.04 32-bit with Unity. My system configuration is: CPU: Core 2 Quad Q6600 (2.4 GHz) RAM: 8192 Mb DDR2 Kingston Video: Palit GeForce GTX 260 216 SP, and my screen resolution is 1680x1050. I also have Window 7 Ulitimate installed, and I can see the same files in Media Player Classic without any horizontal lines. I've installed vdpau driver, NVIDIA drivers 304.51, and MPlayer 2 (within SMPlayer). I've disabled "Sync to VBlank" option in CCSM (because in other way, by default, MPlayer process use about 50-60 percents of my processor load), tried to swich between different deinterlace options in SMPlayer, used "-vc ffh264vdpau,ffmpeg12vdpau" (without quotes) parameters for MPlayer, switched to "Ubuntu 2D", but, finally, have no results. Any suggestions? How must I to set up MPlayer?

  Read the article

• My laptop suppose to have 6 GB ram but it's only 2 GB installed

  - by monablo

  My laptop is supposed to have 6 GB ram but it only detects 2 GB of it, so I don't know what to do. I searched the web for answer and what i get that there's 2 possible problem: 1- That 4 GB ram card is broken and not working 2- or the 2 ram card have a different path so the windows chose the path of the smaller ram card which would be the 2 GB ram I don't know what is the path in first place so I really don't know what to do. How would I troubleshoot, and work out why the 4 GB stick is not being detected? My laptop's specifications are as follows: Windows 7 Home premium 64- bit Operating system processor : intel (R) core(TM) i7 CPU Q740 @1.73 GHz 1.73GHz installed memory(RAM) : 2.00 GB (but it suppose to be 6 GB -_- ) My laptop is Dell and it's Model N5010

  Read the article

• Gitosis installation of public key not working...

  - by user29600

  I've been following this tutorial to install and setup git on Ubuntu Server 10.04 using Windows 7 as a client. However, after finally figuring out how it works (executed gitosis-init a bunch of times on the wrong key), I copied the id_rsa.pub file over to the server in /tmp folder and ran it again. Unfortunately it still doesn't work and when I execute git clone [email protected]:gitosis-admin.git it asks for gitosis's password rather than the RSA Passphrase. I'm assuming is the same problem this guy is having here... however, after following his instructions: Purge git-core and gitosis and manually remove the /srv/gitosis folder and following the instructions again (with the proper id_rsa.pub file this time), I'm still having the same issue. Anyone know what I'm doing wrong? Is there any way to probe for more information that might help in solving this?

  Read the article

• Sound card issues (High Definition Audio Controller)

  - by Prakash R

  I have a 5-year-old Acer Aspire 4520. Until a month back it was working beautifully on Windows 7 32bit. But then out of the blue, the sound stopped working. I've tried reinstalling the OS 3-4 times. The sound came back a couple of times, but it stopped working after a reboot. Even after installing the sound drivers, I don't see any entry in the Playback tab of the Sound applet in Control Panel. I see a High Definition Audio Controller entry in Device Manager. I disabled and uninstalled it, but Windows reinstalls it automatically. I'll share specific hardware details if anybody here needs to know. The processor is "AMD Athlon(tm) 64 X2 Dual-Core Processor TK-55". Any help would be appreciated.

  Read the article

• anonymous access to ftpd

  - by gcb

  I need FTP on my local LAN so my scanner can send me scans. I am on Debian sid. I installed ftpd and created the user anonymous. I removed anonymous from /etc/ftpusers When I try to login as anonymous it says: login failed. I can't seem to find any log file. I'm using FTP server (Version 6.4/OpenBSD/Linux-ftpd-0.17) update:I needed that so my printer had one place to store my scanned documents on the LAN. solved that buying a dedicated USB pen drive (thankfully I bought a printer one with plenty of options) but in the past this was a very simple task. Install ftpd, specify the directory for anonymous access, and be done with it. now every ftp daemon has several layers of security and chroot in it's core... this is just crazy when all you need a place for a printer to dump files in a secured network.

  Read the article

• oracle virtualbox doesn't work for host Kubuntu since Lucid Lynx 10.04

  - by 13east

  I have a thinkpad edge 14 core i3 2.4 ghz and 4g ram; I have tried kubuntu 10.04, 10.10, 11.10, 12.04 and 12.10 (all x64 architecture); Both oracle and ose virtualbox only works properly to install XP and windows 7 quest system on kubuntu 10.04; For every other kubuntu release since, the guest installation goes as far as formatting the virtual drive, freezes at this step, and doesn't even go as far as copying files to hard-drive to begin installation. But virtualbox has not stopped responding to commands; I can kill that one specific window with the problem installation ("machine" - "close" - "power off the machine") and start over again without having to force-kill virtualbox application. If anyone knows how I can go about addressing this problem, any help you can provide would be very much appreciated. Thank You.

  Read the article

• nagiosgraph new services not showing

  - by Eleven-Two

  I am using Nagios Core with Nagiosgraph and had only enabled graphing for cpu usage for a while. This worked fine, but now i wanted to add some more services (for example memory usage). The new services are not working (no rrd data is generated). The Nagiosgraph site only says "no data available" and I get no error in apache log, nagiosgraph.log or nagiosgraph-cgi.log. The new services are standard services (nsclient++ MEMUSE for example) and of course they are included in the map file. If I execute the checks manually, it shows also the perfdata. I added the services by enabling the "graphed-service" use. Did I miss something?

  Read the article

• BSOD after PC has been running for a while

  - by user1389999

  I'm having a problem where my computer is getting a blue screen. I have noticed that the BSOD happens after the PC has been running for about 2 days. The BSOD's seem to be an error with atikmpag.sys with an error code of 0x00000116. The problem started about a month ago.It has happened all five times that I left my computer on that long in the past month. Because my computer is a pre-built one from Dell, and I had upgraded the graphics card (at least a year ago) to a more demanding one, I replaced the stock 360W power supply that came with it. I replaced it with a more powerful, 680W one, because it seemed like the problem could be related to a lack of power supply wattage, but it didn't affect the problem at all. Here are the minidump files for the five BSOD's that I have experienced: https://dl.dropbox.com/u/3488338/bsoddumps.zip System info: Windows 7 Home Premium x64 Dell Studio XPS 435MT Radeon HD 5670 (Version 12.4 of the Catalyst driver) Intel Core i7 920 2.67 GHz 6GB of RAM

  Read the article

• Cisco NAC: help with enabling FTP or moving update files

  - by kyoung

  Hi, So this is a LINUX question, and a Cisco NAC question. I'm trying to update our server from 4.1 to 4.7, and i need to move some tarball files to the NAC. the NAC Appliance runs some strange stripped down version of Fedora Core 4 copying the upgrade: The instructions say to FTP the file to the NAC appliance, however whenever i use WinSCP with root credentials, i get a notice informing me the connection was actively refused. I can't for the life of me find any .conf files that sound like winners, so I don't know how to change the settings, however the ftp command does seem to work. what exactly should I do here?

  Read the article

• Enable a program in Windows to run multiple times?

  - by user135490

  I've got this legacy software that only allows you to run one copy at a time, it detects that you have another session opened and it won't allow you to open a second instance. The problem is this is a cpu intensive program and it only use a single core. Is there any hacks or tweaks so I can trick it and open more than one instance? This would allow me to retire about 5 servers... I'm using Windows 2008 R2. I had to use cff explorer to enable the use more than 2GB RAM as the program crashes when it tries to use more than 2GB.

  Read the article

• NVIDIA Driver Crashing on Custom-Built Windows 7 PC

  - by srunni

  I've got a custom-built PC with these specs: Fractal Design Define R3 ASUS P8Z77-V motherboard Intel Core i7-2700k with Thermalright HR-02 Macho Cooler NVIDIA GeForce GTX 560 with Arctic Cooling Accelero Twin Turbo II Cooler Crucial M4 128 GB SSD 1 TB Hitachi HDD G.SKILL Ares Series 2x8 GB RAM (x2) SeaSonic 520W PSU Windows 7 Ultimate SP1 (x64) NVIDIA driver version 301.42 Upon building the PC, I overclocked the CPU (but never the GPU), and there were no problems for 1-2 months. Then I started getting crashes with this error when doing anything that's computationally or graphically intensive: I un-overclocked the CPU, but that hasn't fixed anything. This is what the inside of my case looks like: I'd appreciate any guidance on resolving this problem. I did get some of the thermal paste on the graphics card when installing the aftermarket cooler, but there were no issues for a month or two. Update I did a clean install and the issue persisted - looks like it's a hardware issue. I will try removing/cleaning/reseating all the parts.

  Read the article

< Previous Page | 535 536 537 538 539 540 541 542 543 544 545 546  | Next Page >