Search Results

Search found 30871 results on 1235 pages for 'click ok'.

Page 554/1235 | < Previous Page | 550 551 552 553 554 555 556 557 558 559 560 561  | Next Page >

• Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

  - by user1622959

  A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

  Read the article

• mount ext4 formated external drive->the drives green light won't stop flashing

  - by Gohlool

  I've installed kubuntu (after 10 years I am trying to play with linux) and manged to attach a external 1TB HDD drive over USB! The drive was formatted with NTFS and everything was working OK. I also changed the /etc/fstab here is my ntfs mount setting: /dev/sdb1 /media/samsung nts-3g auto,user,uid=1000,gid=1000,fmask=000,utf-8 0, 0 Now, I've reparationed the drive and formated it with ext4 filesystem! change my fstb like: /dev/sdb1 /media/samsung ext4 defaults,noatime 0, 0 now, when I plug my dive/or call sudo mount -a, my external drive's green light starts to flash and won't stop, but mount works .... What is the Problem? is this because of ext4? because with NTFS this won't happen! btw. after changing the owner of the /media/samsung and setting permissions 777, I can also access my drive like creating new folder atc. (although is's flashing constantly)! What is my mistake? btw. can you please let me know how to set the owner and the permissions for my /media/samsung directory in fstab for ext4 like I did it for NTFS? Thanks in advance

  Read the article

• Review of TechEd 2012 - so far

  - by Stefan Barrett

  Disclaimer: probably going to next years TechEd.  (but not 100% sure) As with most TechEd's, this is not one of the best - but it's not bad.  Some impressions so far: The food is not bad, through perhaps not as much choice as in previous years.  The snacks, while a bit limited, are at least available.  The alumni lounge is ok, through perhaps not as good as last years.  Wifi is a bit worse than previous years - not really working in the big room, and a bit sporadic in the rest of the building. The device seems to make a big difference - the iPad seems to connect the easiest, while the iPhone & Lumia 800 are really struggling.  The real problem is the content - not as developer focused as in previous years.  This shows up in a number of different ways, for example while there is a visual studio booth, there is not much sign of anybody from the language teams.  This is one of few TechEd's where I don't feel very surprised about anything - seen most of the developer stuff in previews. One example where I was surprised was the pre-conf on c++ - its been years since I did any c++, but based on that session perhaps I should start again. While there are sessions, I'm not finding my schedule very challenged. For each time-slot there only seems to 1, or rarely 2, interesting sessions.  The focus seems to be on windows 8, Azure and the phone, which while interesting (might give win8 a go), are not enough.

  Read the article

• Calc direction vector based on destination vector and distance from enemy in AS3

  - by Phil

  I'm working on a zombie game in AS3 where I want a character to be able to move away from a zombie depending upon how close the zombie is. The character also has a destination that it's trying to get too on the screen. Ok so I have 2 vectors, one pointing to my destination, and one pointing to the zombie which I then invert to get my "away" vector. I then turn the distance between my character and the zombie into a value between 0 and 1. And then I'm stuck on how to get a resultant vector for my character. How would I use my 0-1 value to calculate how much of the away vector is used and how much of the original destination vector is still left if that makes sense? to end up with 1 direction vector to move my character? So if the zombie is right where my character is, then my direction vector = away vector, and if I'm far away from the zombie than my direction vector = destination vector, but how do I calculate the in-between? Ideally need the answer in AS3.

  Read the article

• Dealing with the node.js callback pyramid

  - by thecoop

  I've just started using node, and one thing I've quickly noticed is how quickly callbacks can build up to a silly level of indentation: doStuff(arg1, arg2, function(err, result) { doMoreStuff(arg3, arg4, function(err, result) { doEvenMoreStuff(arg5, arg6, function(err, result) { omgHowDidIGetHere(); }); }); }); The official style guide says to put each callback in a separate function, but that seems overly restrictive on the use of closures, and making a single object declared in the top level available several layers down, as the object has to be passed through all the intermediate callbacks. Is it ok to use function scope to help here? Put all the callback functions that need access to a global-ish object inside a function that declares that object, so it goes into a closure? function topLevelFunction(globalishObject, callback) { function doMoreStuffImpl(err, result) { doMoreStuff(arg5, arg6, function(err, result) { callback(null, globalishObject); }); } doStuff(arg1, arg2, doMoreStuffImpl); } and so on for several more layers... Or are there frameworks etc to help reduce the levels of indentation without declaring a named function for every single callback? How do you deal with the callback pyramid?

  Read the article

• Problem graphics with ATI Radeon x1270 (RS690M) on Ubuntu 12.04

  - by Giuseppe Della Corte

  I'm Italian and so I apologize for my English! I'm a beginner to Ubuntu and I tried it on my desktop PC and it's fantastic, fast and fun! I decided to try it on my netbook Packard Bell DOT M/A and this is the configuration: AMD Athlon L110 1.2GHz 2GB of RAM ATI Radeon x1270 (RS690M) 150GB Hard Disk I installed Ubuntu 12.04 with Wubi (dualboot Windows 7 + Ubuntu 12.04), because the netbook does not have a DVD player! During the installation everything is OK, after it was installed I see mistakes in the graphical display! I see objects that are seen in different colors and moving (buttons, mouse pointer, text bar ... etc ...) At one point came not to see anything, such as this screenshot: The drivers are open, that is already installed in Ubuntu. Windows 7 video card runs fine, can run well Aero (transparent window effects), I can watch movies in HD and play some games with the Catalyst drivers from AMD. Now I ask a favor, you can help me solve this problem? Is there a fix for this driver or drivers different on the Internet? Thanks for your attention, good bye!

  Read the article

• Unable to install ubuntu on a AMD 64 bit system with a AMD Radeon HD 6670 graphics card

  - by Tom Wingrove

  I’ve been running a dual boot system (Ubuntu/Windows7) for two years or so with no problems. I recently built an AMD 64 Bit System, re-installed Windows but when I went to load Ubuntu inside Windows, hit a snag. The screen view during installation became small square blocks of colour, which obviously is a graphics drive problem. I tried various live disks both 32 & 64 bit for, Ubuntu 12.04, 11.10 & 10.10, all but Ubuntu 10.10 had the same problem. Ubuntu 10.10 loaded ok, installed the presented ATI graphics driver as usual but was left with the AMD Unsupported watermark at the bottom right of the screen. The graphics card installed in the computer is an MSI ATI Radeon HD 6670 (in effect an AMD Radeon HD 6670). I am fairly new to linux and while I can install and tweak the OS, I am rather baffled as to what to do. So my question is will an up to date ATI Driver be released in the near future for installation/live disks? Or am I going to have to downgrade my graphics card to use linux? Yours Tom Wingrove

  Read the article

• Using Ogre with android [closed]

  - by Rich

  I am trying get Ogre 3d to work on android, I have managed to download and run the ogre sample browser but I am really struggling with trying to get a basic application working i have been trying for days now with no avail. Does anyone have any pointers on where to start with this? Thanks if anyone can help EDIT: Very sorry for my rubbish question! I am a bit new to this and I am just trying to seek some guidance. Ok so i followed the instructions on the Ogre wiki to build ogre for android and the sample browser here: http://www.ogre3d.org/tikiwiki/tiki-index.php?page=CMake+Quick+Start+Guide&tikiversion=Android so it is deffinately possible. The issue I am having is knowing what I need to do to get started with ogre e.g just a simple hello world style app where it might just show the ogre head, so tutorials might actually be good because I could not really find any simple ones as I am very new to 3D development. I just found that the sample browser was just massive and yes it has everything in it but it's very difficult to understand how it all works. What I am asking is basically some help, as I have been trying to pull out some parts of the sample browser to just create a view with a 3D model. Hope this is better?

  Read the article

• Changing domain name - what are the practical steps involved

  - by Homunculus Reticulli

  I launched a website a couple of years ago, bright eyed and bushy tailed, with dreams of conquering the world. Unfortunately it wasn't to be. Now, that I am a bit older and wiser, I have spent some money on branding and creating more quality content etc, I am rebranding and relaunching the site with a new domain name. Although the traffic on the old site is laughable (i.e. non-existent), there are a few pages of good information on there and I don't want to lose any "juice" those pages may have gained because web crawlers have been seeing it for a few years now. Ok, the upshot of all that is this: I want to change my domain name from xyz.com to abc.com. I am maintaining the same friendly urls I had before, only the domanin name part of the url will change, so that any traffic coming to the old page will be forwarded/redirected? to the new page seamlessly. How do I go about achieving this (i.e. what are the steps I need to carry out, and to minimize any "disruption" to any credibility the existing site has with Googlebot etc? I am running Apache 2.x on a headless Linux (Ubuntu) server.

  Read the article

• SQL Saturday #89 in Atlanta!

  - by Most Valuable Yak (Rob Volk)

  (Yeah yeah, technically it's in Alpharetta, but it's close enough.) Saturday…Saturday….Saturday…. September 17th.  TWO THOUSAND ELEVEN! OK, it's not a tractor pull, but it's even better:  FREE SQL SERVER TRAINING!  They have a bunch of great speakers lined up, and for some reason, me.  (Protip: be good friends with the program committee, have sufficient bribe funds, and if all else fails, lots of alcohol, drugs and a camera.  Ba-ZING!  You too can speak at SQL Saturday!) I will be presenting Revenge: The SQL! in a new and improved SQL Saturday themed presentation.  Actually, it's the same ol' presentation, I just updated the slide theme to match the new SQL Saturday website design.  (Yeah guys, thanks for changing that a month ago.  So much for coasting on the old format.) Of course, you have your choice of three other SQL Saturdays in other cities that day, but come on, you really want to go to this one. #sqlsat89 #sqlsaturday #sqlkilt #sqlpass

  Read the article

• Testing of visualization projects

  - by paxRoman

  We develop small to large visualization projects for different tasks and industries and sometimes while rewriting them a couple of times in the process we hit walls because we discover that we need to add a lot of code to support new requirements. Now we have established a design process that seems to work well (at least we reduced the development time for each new project quite a bit), but we're still left scratching our heads around this question: what exactly should we test when testing visualizations? If everything that we want to explore is on the screen (bounded visualizations)? If the data is ok - if data is valid (that's one of the nice things about visualizations you can spot errors in your datasets)? Usability? User interaction? Code quality? I can tell you for sure that a simple check of the code quality is certainly not enough! Is there a classic paper / book about how to test visualizations? Also do you happen to know about classic design patterns for visualizations (except the obvious ones like Pub-Sub)?

  Read the article

• What is the disadvantage of using abstract class as a database connectivity in zend framework 2 instead of service locator

  - by arslaan ejaz

  If I use database by creating adapter with drivers, initialize it in some abstract class and extend that abstract class to required model. Then use simple query statement. Like this: namespace My-Model\Model\DB; abstract class MysqliDB { protected $adapter; public function __construct(){ $this->adapter = new \Zend\Db\Adapter\Adapter(array( 'driver' => 'Mysqli', 'database' => 'my-database', 'username' => 'root', 'password' => '' )); } } And use abstract class of database like this in my models: class States extends DB\MysqliDB{ public function __construct(){ parent::__construct(); } protected $states = array(); public function select_all_states(){ $data = $this->adapter->query('select * from states'); foreach ($data->execute() as $row){ $this->states[] = $row; } return $this->states; } } I am new to zend framework, before i have experience of working in YII and Codeigniter. I like the object oriented in zend so i want to use it like this. And don't want to use it through service locater something like this: public function getServiceConfig(){ return array( 'factories' => array( 'addserver-mysqli' => new Model\MyAdapterFactory('addserver-mysqli'), 'loginDB' => function ($sm){ $adapter = $sm->get('addserver-mysqli'); return new LoginDB($adapter); } ) ); } In module. Am i Ok with this approach?

  Read the article

• How to make my simple round sprite look right in XNA

  - by Joshua Perina

  Ok, I'm very new to graphics programming (but not new to coding). I'm trying to load a simple image in XNA which I can do fine. It is a simple round circle which I made in photoshop. The problem is the edges show up rough when I draw it on the screen even with the exact size. The anti-aliasing is missing. I'm sure I'm missing something very simple: GraphicsDevice.Clear(Color.Black); // TODO: Add your drawing code here spriteBatch.Begin(); spriteBatch.Draw(circle, new Rectangle(10, 10, 10, 10), Color.White); spriteBatch.End(); Couldn't post picture because I'm a first time poster. But my smooth png circle has rough edges. So I found that if I added: spriteBatch.Begin(SpriteSortMode.FrontToBack, BlendState.NonPremultiplied); I can get a smooth image when the image is the same size as the original png. But if I want to scale that image up or down then the rough edges return. How do I get XNA to smoothly resize my simple round image to a smaller size without getting the rough edges?

  Read the article

• Problem with wake after suspend using USB remote.

  - by Bod

  Hi, I'm a linux newbie looking for some help. I'm currently setting up an XBMC HTPC using a laptop and 10.10 and all works great except for waking from resume using the power button on the remote. The suspend works from remote works fine as does the resume using the power button on the laptop. I've checked /proc/acpi/wakeup which initially showed the following. Device S-state Status Sysfs node C096 S5 *disabled pci:0000:00:1e.0 C0F1 S3 *disabled pci:0000:00:1d.0 C0F8 S3 *disabled pci:0000:00:1d.1 C0F9 S3 *disabled pci:0000:00:1d.2 C0FA S3 *disabled pci:0000:00:1d.3 C0FB S3 *disabled pci:0000:00:1d.7 C102 S5 *disabled pci:0000:00:1c.0 C22B S5 *disabled pci:0000:08:00.0 C115 S5 *disabled pci:0000:00:1c.2 C22C S5 *disabled C118 S5 *disabled pci:0000:00:1c.3 C22C S5 *disabled I've since configured the above so that the S3 devices above are enabled. I've confirmed that they are the correct devices using lspci 00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01) None of this has worked unfortunately and I'm now stuck. It simply refuses to wakeup from the remote. The USB receiver shows no activity LED while suspended. Suspend/resume from the remote works fine from Windows 7 so I know the laptop is ok with it. Any ideas? I need to get this sorted to gain Wife Approval for this system. Thanks, Bod.

  Read the article

• Ubuntu 12.04 and Nvidia GTX 550 Ti

  - by Jim

  OK I'm currently trying to install Ubuntu x64 Server 12.04 onto the following machine: Intel Core i5-2320 3.0GHz LGA1155 6MB 8 GB DDR3 RAM, Gigabyte Z68P-DS3 S1155 Intel Z68 DDR3 ATX M/B, OCZ 60 GB SSD, 3x Samsung 2TB drives in a RAID 5 array (via M/B) Now what I think is causing the issue is the following: EVGA GeForce GTX 550 Ti 951MHz 1GB PCI-Express HDMI FPB As the server CD works in text mode I haven't had a problem with actually installing Ubuntu. Partioned with: 1GB /boot SSD, 59GB / SSD, 10GB swap RAID5, ~4TB /home RAID5 On a straight boot, you briefly see the GRUB menu, followed by a blank screen. The keyboard and mouse blink as they are initialised but no sign of life from the screen. Followed by a bit of research (otherwise known as google) ... Booted in quiet splash nomodeset Now I have a fully working linux distro at the command prompt. I then proceed to try and update the nvidia drivers with apt-get (after updating repositories etc) and rebooting. Still the same problem. I also tried reinstalling from the CD and installing said drivers in the install process before GRUB was installed, still the same symptoms. Does anybody have any solutions? I'm at my wits end here, I bought this machine to be a linux server / tinkering machine and have just spent 4-5 hours trying to just get a basic install working.

  Read the article

• Code Clone Analysis on Rawr &ndash; Part 1

  - by Dylan Smith

  In this post we’ll take a look at the first result from the Code Clone Analysis, and do some refactoring to eliminate the duplication.  The first result indicated that it found an exact match repeated 14 times across the solution, with 18 lines of duplicated code in each of the 14 blocks.   Net Lines Of Code Deleted: 179     In this case the code in question was a bunch of classes representing the various Bosses.  Every Boss class has a constructor that initializes a whole bunch of properties of that boss, however, for most bosses a lot of these are simply set to 0’s.     Every Boss class inherits from the class MultiDiffBoss, so I simply moved all the initialization of the various properties to the base class constructor, and left it up to the Boss subclasses to only set those that are different than the default values. In this case there are actually 22 Boss subclasses, however, due to some inconsistencies in the code structure Code Clone only identified 14 of them as identical blocks.  Since I was in there refactoring the 14 identified already, it was pretty straightforward to identify the other 8 subclasses that had the same duplicated behavior and refactor those also.   Note: Code Clone Analysis is pretty slow right now.  It takes approx 1 min to build this solution, but it takes 9 mins to run Code Clone Analysis.  Personally, if the results are high quality I’m OK with it taking a long time to run since I don’t expect it’s something I would be running all that often.  However, it would be nice to be able to run it as part of a nightly build, but at this time I don’t believe it’s possible to run outside of Visual Studio due to a dependency on the meta-data available in the VS environment.

  Read the article

• FTP gives me a error when uploading and deleting files [on hold]

  - by AR Games

  Here's the error I get when trying to delete files... Command: DELE index.html Response: 550 Delete operation failed. Here's the error I get when trying to upload files... Command: OPTS UTF8 ON Response: 200 Always in UTF8 mode. Status: Connected Status: Starting upload of C:\wamp\www\.DS_Store Command: CWD /var/www/html Response: 250 Directory successfully changed. Command: TYPE A Response: 200 Switching to ASCII mode. Command: PASV Response: 227 Entering Passive Mode (76,185,76,101,78,222). Command: STOR .DS_Store Response: 553 Could not create file. Error: Critical file transfer error Status: Retrieving directory listing... Command: TYPE I Response: 200 Switching to Binary mode. Command: PASV Response: 227 Entering Passive Mode (76,185,76,101,23,94). Command: LIST Response: 150 Here comes the directory listing. Response: 226 Directory send OK. Status: Directory listing successful Response: 421 Timeout. Error: Connection closed by server Status: Disconnected from server IM running windows OS and using filezilla FTP client

  Read the article

• Moving while doing loop animation in RPGMaker

  - by AzDesign

  I made a custom class to display character portrait in RPGMaker XP Here is the class : class Poser attr_accessor :images def initialize @images = Sprite.new @images.bitmap = RPG::Cache.picture('Character.png') #100x300 @images.x = 540 #place it on the bottom right corner of the screen @images.y = 180 end end Create an event on the map to create an instance as global variable, tada! image popped out. Ok nice. But Im not satisfied, Now I want it to have bobbing-head animation-like (just like when we breathe, sometimes bob our head up and down) so I added another method : def move(x,y) @images.x += x @images.y += y end def animate(x,y,step,delay) forward = true 2.times { step.times { wait(delay) if forward move(x/step,y/step) else move(-x/step,-y/step) end } wait(delay*3) forward = false } end def wait(time) while time > 0 time -= 1 Graphics.update end end I called the method to run the animation and it works, so far so good, but the problem is, WHILE the portrait goes up and down, I cannot move my character until the animation is finished. So that's it, I'm stuck in the loop block, what I want is to watch the portrait moving up and down while I walk around village, talk to npc, etc. Anyone can solve my problem ? Or better solution ? Thanks in advance

  Read the article

• Wrong resolution for Lightdm/GDM on Ubuntu 13.04 using HDMI

  - by f03lipe

  I've tried all the solution I could find on the matter so far, but the error persists. My problem is that the login screen (both under gdm and lightdm) runs with the wrong resolution, even though all is fine when I log in. The error occurs solely when I have my HDMI cable connected to my other screen. The login screen resolution becomes 1024x768 (for my 1366x768 laptop screen) and mirrored on my screen, which is 1920x1080. I've had this issue on version 12.04 (the last one before I upgraded to 13.04), but I got it fixed by adding the xrandr commands on the begining of the /etc/gdm/Init/Default file. This doesn't seem to work anymore. I've also tried telling lightdm to run a script fixing the resolution with xrandr (by editing /etc/lightdm/lightdm.conf), but lightdm crashes, and I'm forced to log in with low graphic settigs. Hint: when ubuntu is loading, the resolution starts OK, then goes bad right before the login screen is initialized. Does that mean that there's nothing wrong with my graphic cards? What do you think? Cheers!

  Read the article

• Why can't tuxboot and ubuntu play well together?

  - by mmr

  I'm trying to get clonezilla to run off of a usb stick, and it seems that the right way to do that is via tuxboot. Tuxboot is not compilable on ubuntu. I used git to get it from the repository, and then when I run the 'install' script (because building it is apparently not allowed, since the build script just tries to install windows things). Qmake-linux wants my qmake executable to be in the same directory as the stuff I pulled down, and let's just say that if there's a way to do this easily, I ain't seein' it. So then I download the linux file, the most recent of which is tuxboot-linux-25. Try to run it, get a failure that libpng12.so.0 isn't found. OK, then I go to install that via the instructions I found on the web but firefox seems to have already deleted from my history (yay!) Then I add the /usr/local/lib directory to ldconfig via emacs (had to install that too, of course): http://ubuntuforums.org/showthread.php?t=369848 I still get the errors that libpng12.so.0 cannot be opened because 'No such file or directory'. ldconfig -p | grep libpng shows that the library is there, but it still doesn't seem to be findable. What to do next? (for the record, doing this in windows is painless-- download, click, and it's done. But I'm trying to be all linuxy and get away from Windows for this...)

  Read the article

• Searching for entity awareness in 3D space algorithm and data structure

  - by Khanser

  I'm trying to do some huge AI system just for the fun and I've come to this problem. How can I let the AI entities know about each other without getting the CPU to perform redundant and costly work? Every entity has a spatial awareness zone and it has to know what's inside when it has to decide what to do. First thoughts, for every entity test if the other entities are inside the first's reach. Ok, so it was the first try and yep, that is redundant and costly. We are working with real time AI over 10000+ entities so this is not a solution. Second try, calculate some grid over the awareness zone of every entity and test whether in this zones are entities (we are working with 3D entities with float x,y,z location coordinates) testing every point in the grid with the indexed-by-coordinate entities. Well, I don't like this because is also costly, but not as the first one. Third, create some multi linked lists over the x's and y's indexed positions of the entities so when we search for an interval between x,y and z,w positions (this interval defines the square over the spatial awareness zone) over the multi linked list, we won't have 'voids'. This has the problem of finding the nearest proximity value if there isn't one at the position where we start the search. I'm not convinced with any of the ideas so I'm searching for some enlightening. Do you people have any better ideas?

  Read the article

• backlight doesn't work on acer 5732z tried everything I can find

  - by Dude Random21

  Ok if you can solve my problem you're really really good. I want to run ubuntu 12.04 on my acer aspire 5732z I know (from research) that these computer's have issues with the backlight on ubuntu. So I tried a couple of solutions: The "sudo lightdm restart" method. I get no change at all. The "sudo setpci -s 00:02.0 F4.B=30" method. This so far has been the most effective, I first tried it in the F1 console right away I get the screen back, problem is going back to the desktop it goes back to being black. So I tried it from a terminal window and it works as well but as soon as I unplug my external monitor the screen turns black again and doesn't come back. If I plug the monitor back in the screen stays black and the only thing I see is the mouse pointer. From here I go back into console (which I am able to see) and reboot from there. The "sudo sed -i 's/GRUB_CMDLINE_LINUX=""/GRUB_CMDLINE_LINUX="acpi_osi=Linux"/g' /etc/default/grub" method. This one I got no instant change and after reboot still no change. I'm open to pretty much any suggestions you may have.

  Read the article

• Java enum pairs / "subenum" or what exactly?

  - by vemalsar

  I have an RPG-style Item class and I stored the type of the item in enum (itemType.sword). I want to store subtype too (itemSubtype.long), but I want to express the relation between two data type (sword can be long, short etc. but shield can't be long or short, only round, tower etc). I know this is wrong source code but similar what I want: enum type { sword; } //not valid code! enum swordSubtype extends type.sword { short, long } Question: How can I define this connection between two data type (or more exactly: two value of the data types), what is the most simple and standard way? Array-like data with all valid (itemType,itemSubtype) enum pairs or (itemType,itemSubtype[]) so more subtype for one type, it would be the best. OK but how can I construct this simplest way? Special enum with "subenum" set or second level enum or anything else if it does exists 2 dimensional "canBePairs" array, itemType and itemSubtype dimensions with all type and subtype and boolean elements, "true" means itemType (first dimension) and itemSubtype (second dimension) are okay, "false" means not okay Other better idea Thank you very much!

  Read the article

• Why does my root filesystem keep becoming read-only?

  - by Scott Severance

  I've lately been having an issue with my root filesystem becoming readonly. It happens some amount of time after boot. I don't know exactly when it happens, as I don't usually notice it until something such as suspending the computer or printing fails. It seems to be fairly random. Since most of my system is on that partition, I can't re-mount it without rebooting. After this happens, the system runs a fsck. Sometimes it prompts to fix problems; other times it apparently finds none. To troubleshoot, I've searched through the logs but found nothing relevant. This might be due in part to not knowing when the actual errors took place. The filesystem is apparently good to begin with, as when fsck runs its fixes it doesn't report any errors. I've scanned the disk with SpinRite. A while ago, SpinRite found and recovered from some bad sectors on the hard drive. I ran a level 4 scan (a thorough scan) after this probem appeared, but SpinRite found nothing. The SMART data reports that the disk is OK with 63 bad sectors. The number of bad sectors hasn't changed recently. I realize that the disk isn't in the best of conditions, and I have complete backups in case of catastrophic failure. Yet the lack of errors in the logs, combined with SpinRite's test results and the unchanged SMART data makes me think that this problem has some cause other than disk failure. Other than disk failure, what could cause my symptoms?

  Read the article

• configuration issue with respect to .htaccess file on ubuntu

  - by Registered User

  I am building an application tshirtshop I have following configuration in /etc/apache2/sites-enabled/tshirtshop <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www/tshirtshop <Directory /var/www/tshirtshop> Options Indexes FollowSymLinks AllowOverride All Order allow,deny allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> and following in .htaccess file in location /var/www/tshirtshop/.htaccess <IfModule mod_rewrite.c> # Enable mod_rewrite RewriteEngine On # Specify the folder in which the application resides. # Use / if the application is in the root. RewriteBase /tshirtshop #RewriteBase / # Rewrite to correct domain to avoid canonicalization problems # RewriteCond %{HTTP_HOST} !^www\.example\.com # RewriteRule ^(.*)$ http://www.example.com/$1 [R=301,L] # Rewrite URLs ending in /index.php or /index.html to / RewriteCond %{THE_REQUEST} ^GET\ .*/index\.(php|html?)\ HTTP RewriteRule ^(.*)index\.(php|html?)$ $1 [R=301,L] # Rewrite category pages RewriteRule ^.*-d([0-9]+)/.*-c([0-9]+)/page-([0-9]+)/?$ index.php?DepartmentId=$1&CategoryId=$2&Page=$3 [L] RewriteRule ^.*-d([0-9]+)/.*-c([0-9]+)/?$ index.php?DepartmentId=$1&CategoryId=$2 [L] # Rewrite department pages RewriteRule ^.*-d([0-9]+)/page-([0-9]+)/?$ index.php?DepartmentId=$1&Page=$2 [L] RewriteRule ^.*-d([0-9]+)/?$ index.php?DepartmentId=$1 [L] # Rewrite subpages of the home page RewriteRule ^page-([0-9]+)/?$ index.php?Page=$1 [L] # Rewrite product details pages RewriteRule ^.*-p([0-9]+)/?$ index.php?ProductId=$1 [L] </IfModule> the site is working on localhost and is working as if there is no .htaccess rule specified i.e. if I were to view a page as http://localhost/tshirtshop/nature-d2 then I get a 404 Error but if I view the same page as http://localhost/tshirtshop/index.php?DepartmentId=2 then I can view it. sudo apache2ctl -M Loaded Modules: core_module (static) log_config_module (static) logio_module (static) mpm_prefork_module (static) http_module (static) so_module (static) alias_module (shared) auth_basic_module (shared) authn_file_module (shared) authz_default_module (shared) authz_groupfile_module (shared) authz_host_module (shared) authz_user_module (shared) autoindex_module (shared) cgi_module (shared) deflate_module (shared) dir_module (shared) env_module (shared) mime_module (shared) negotiation_module (shared) php5_module (shared) reqtimeout_module (shared) rewrite_module (shared) setenvif_module (shared) status_module (shared) Syntax OK What is the mistake if any one can point out in above configuration, or else I need to check any thing else?

  Read the article

< Previous Page | 550 551 552 553 554 555 556 557 558 559 560 561  | Next Page >