Search Results

Search found 16598 results on 664 pages for 'device center'.

Page 555/664 | < Previous Page | 551 552 553 554 555 556 557 558 559 560 561 562  | Next Page >

• Oracle Linux screen freezes during installation

  - by Fearless

  I was installing Oracle Linux 6.4 on a server, and the screen suddenly froze. Here were the previous steps: I put in the disk, clicked install, checked the disk (no errors), did pre-install setup (clock, root password, host+domain name, etc.), configured two 40GB hard drives in a RAID1 array (no swap, 3100mb encrypted raid partitions, ~100mb ext4 partition mounting to /boot, encrypted ext4 RAID device with mounting to /), selected packages, hit continue. The system did its short preinstall processes, then when to the main installation screen with the long status bar. The installer proceeded like always, but around package 250 out of ~1000, the screen suddenly went black with a text cursor in the upper left corner of the screen and the mouse cursor in its previous place. Neither cursor moved and the only thing that triggered a response was a ctrl-alt-delete that rebooted it. I have run this in VMs before without this issue. Memtest hasn't reported anything, and the media check went smoothly. The machine has supported Ubuntu server without issues before. Any ideas? I have tried booting after that, but the grub bootloader tries to find fd0 for some reason (I have no idea why it would search for the floppy disk). UPDATE My server successfully installed, but won't boot up. I think that, for some reason, it is still using the old bootloader from the previous installation. Any ideas on how to fix that?

  Read the article

• How to tell Linux to explicitly swap out main memory of suspended process?

  - by Vi

  I run a memory-hungry process (mkcromfs) which consumes more memory than I have physical memory on my latop, so it is paging and swappin and thrashing all the time and loadavg is about 2 (compcache is already in use with usual swap partition as well), but slowly moving forward (Although I afraid it will finally try to allocate 2GB and crash draining 2 days of thrashing). When I want to use the laptop for something else, I stop the process, start X server, firefox and other programs. The problem is that when I start Firefox the loadavg jumps to 10 and the system becomes almost unresponsive at all (long time to turn on/off caps lock, slow mouse cursor position updates, slow switching from X server to Linux console, slow login). The stopped mkcromfs still holds a lot of memory (464.8 MiB and slowly falling) and moves it to swap only when more memory is needed for some other program, which results in a great slowdown. How to tell the Linux to swap out this process entirely (e.g. I'm not intending to resume it in short term), possibly waking from swap other data? Also it will be useful to be able to specify the exact swap device to swap the given process out.

  Read the article

• Route outbound connections from local network through VPN

  - by Sharkos

  I have a server A running OpenVPN, an OpenVPN client B (a rooted Android phone as it happens) and a third party C (a laptop, tablet etc.) tethered to B. B can use the VPN to access the internet via A; C can use the tethered connection WITHOUT the VPN to access the internet via B. However, with the VPN on B active, I cannot load information from the internet on C. A appears to log similar traffic inbound and outbound when B or C attempt to load a webpage, say, but the VPN on device B reports no inbound traffic when the connection originated from C. Where should I look for packets being dropped, and what ip rules should I use to make sure they are passed back through the VPN and into the local network B <- C? (I'll obviously post whatever further information is needed.) Further info Without VPN: root@android:/ # ip route default via [B's External Gateway] dev rmnet0 [B's External Subnet] dev rmnet0 proto kernel scope link src [B's External IP] [B's External Gateway] dev rmnet0 scope link 192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.1 With VPN: root@android:/ # ip route 0.0.0.0/1 dev tun0 scope link default via [B's External Gateway] dev rmnet0 [B's External Subnet] dev rmnet0 proto kernel scope link src [B's External IP] [B's External Gateway] dev rmnet0 scope link [External address of A] dev tun0 scope link 128.0.0.0/1 dev tun0 scope link 172.16.0.0/24 dev tun0 scope link 172.16.0.8/30 dev tun0 proto kernel scope link src 172.16.0.10 192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.1 192.168.168.0/24 dev tun0 scope link

  Read the article

• Different subnets routing with just one layer 3 switch

  - by GustavoFSx

  Our current network looks like this: Location 1: 2 Layer 2 switches | subnet 192.168.1.0/24 | Firewall for our VPN Location 2: 1 Layer 2 switch | subnet 192.168.3.0/24 | Firewall for our VPN Location 3: 1 Layer 2 switch | subnet 192.168.5.0/24 | Firewall for our VPN We just got a direct fiber connection between location 1 and 2, we also got a new HP V1910 24G layer 3 switch. I tried to follow the instructions on this site, but I can't get it to work. I think our network should look like this: Location 1: HP Switch FIBER to L2 | subnet 192.168.1.0/24 | Firewall for our VPN Location 2: 1 Layer 2 switch | subnet 192.168.3.0/24 | FIBER to L1 Location 3: 1 Layer 2 switch | subnet 192.168.5.0/24 | Firewall for our VPN So, how can I get routing working on our location 2? It's old gateway was a firewall device on ip 192.168.3.1. I'm thinking on creating a VLAN Interface on 192.168.3.1 on the switch for the Location 2. But how will I handle that on the HP switch that has a direct fiber connection with that switch? Please help, I'm not very good with networking.

  Read the article

• How do I find the Serial Number of a USB Drive?

  - by jamuraa

  I'm trying to re-enable USB Autoplay in a secure way, by installing a program on each of the computers that I use so that I can run my launcher (PStart in this case) whenever I plug in my specific USB drive. The tool that I'm using to enable this - AutoRunGuard - needs the serial number of the USB drive that I am using. I can't figure out where to find this in Windows. Ideally I would not need to install and run a separate program to do this (seemingly) simple task. Since this is a pretty easy question, bonus points if you also tell me how to discover it in Linux as well. What steps do I need to take to retrieve a USB Drive's serial number? UPDATE: Just incase people come here looking for the answer for AutoRunGuard, I discovered that they don't want the USB device serial number, but the volume serial number. The drive serial can be found by going into the command line, navigating to the drive, and executing dir. The volume serial number is found in the top two lines - use it without the dash.

  Read the article

• How can I generate filesystem images that are usable on many different virtualization systems?

  - by Mark Longair

  I have written a script that generates a root filesystem image (based on Debian lenny) suitable for User-Mode Linux. (Essentially this script creates a filesystem image, mounts it with a loop device, uses debootstrap to create a lenny install, sets up a static IP for TUN/TAP networking, adds public keys for login by SSH and installs a web application.) These filesystem images work pretty well with UML, but it would be nice to be able to generate similar images that people can use on alternative virtualization software, and I'm not familiar with these options at all. In particular, since the idea is to use this image as a standalone server for testing the web application, it's important that the networking works. I wonder if anyone can suggest what would be involved in customizing such root filesystem images such that they could be used with other virtualization software, such as VMware, Xen or as an Amazon EC2 instance? Two particular concerns are: If such systems don't use a raw filesystem image (e.g. they need headers with metadata or are compressed in some particular way) do there exist tools to convert between the different formats? I assume that in the filesystem, at least /etc/network/interfaces will have to be customized, but are more involved changes likely to be necessary? Many thanks for any suggestions...

  Read the article

• Determining how all memory is used in Windows Server 2008

  - by Mojah

  Hi, I have a Windows Server 2008 system, which has 12GB of RAM. If I list all processes in the Task Manager, and SUM() the memory of each process (Working Set, Memory (Private Working Set), Commit Size, ...), I never reach more than 4-5GB that should be "in use". However, task manager reports this server has 11GB in use via the "Performance" tab. I'm failing in determining where all that used RAM is going. It doesn't seem to be system cache, but I can not be sure. It might be a memory leak in one of the appliances, but I'm struggling to find out which one. The server's memory keeps filing up, and eventually forces us to reboot the device to clear it. I've been reading up on how RAM assignments work on Windows Server: RAM, Virtual Memory, Pagefile and all that stuff: http://support.microsoft.com/kb/2267427 What's the best way to measure? http://www.zdnet.com/blog/bott/windows-7-memory-usage-whats-the-best-way-to-measure/1786 Configure the file system cache in Windows: http://smallvoid.com/article/winnt-system-cache.html But I fear I'm stuck without ideas at the moment.

  Read the article

• Using GPO to collect data about VMware view activity

  - by MoSiAc

  Our security group wants us to begin logging data for external access to our view enviroment. At first we thought that view security would be logging all source ip's that are external in nature so if for some reason there is an intrusion we would have record of it there. Of course our firewall logs all that information but correlating it to view is sketchy at best with our current implementation. We know on viewdesktops there is a set of keys in VolitateEnviroment that contains stuff such as source ip and username, etc. We have a script in place that, when run as a logon script attached to a user account in AD collects the information as we need it. If we have a GPO run the same script the information does not get collected. We feel like there is a piece of the puzzle we're missing but we don't know what. If anyone knows what we're forgetting or misconfiguring that would be great, or if you have a better way of us collecting external source ip's for view specifically we'd be interested in that as well. Thanks, EDIT CODE Batch script to dump to text file @echo off timeout 20 echo %computername%/%username% %time% %date% c:\vdi\vmware.txt echo ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~c:\vdi\vmware.txt reg query "HKEY_CURRENT_USER\Volatile Environment" /v "ViewClient_LoggedOn_Username"c:\vdi\vmware.txt reg query "HKEY_CURRENT_USER\Volatile Environment" /v "ViewClient_IP_Address"c:\vdi\vmware.txt echo.c:\vdi\vmware.txt VB Script to display values Const HKEY_CURRENT_USER = &H80000001 Set wmiLocator=CreateObject("WbemScripting.SWbemLocator") Set wmiNameSpace = wmiLocator.ConnectServer(".", "root\default") Set objRegistry = wmiNameSpace.Get("StdRegProv") sPath = "Volatile Environment" lRC = objRegistry.GetStringValue(HKEY_CURRENT_USER, sPath, "ViewClien_Machine_Name", vMachine) lRC = objRegistry.GetStringValue(HKEY_CURRENT_USER, sPath, "ViewClien_IP_Address", vIP) lRC = objRegistry.GetStringValue(HKEY_CURRENT_USER, sPath, "ViewClien_MAC_Address", vMAC) msgbox "The Remote Device Name is " & vMachine & " @ " & vIP & " (" & vMAC & ") " he wanted me to mention that the batch file actually runs and I can see it counting down when I reconnect but it does not grab the registry values.

  Read the article

• fglrx-legacy-driver not seeing Radeon HD 4650 AGP

  - by Rocket Hazmat

  I am running Debian Squeeze on an old Dell Dimension 8300 box. It has an AGP Radeon HD 4650 card. I use this machine to mine bitcoins, and today I noticed that the machine had rebooted! My precious uptime! Anyway, my miner wouldn't start, so I figured might as well update my graphics driver, maybe that would fix the issue. I went to amd.com and downloaded the newest driver (12.6 legacy), but after installing it, aticonfig gave an error: aticonfig: No supported adapters detected I uninstalled the driver and figured I'd try to install it from apt. AMD has dropped support for the HD 4000 series in fglrx, forcing me to use fglrx-legacy-driver (currently only in experimental). In order to install this, I had to update libc6 (and some other important packages, like gcc), I had to use their wheezy versions. I finally got glrx-legacy-driver installed, but I still got: aticonfig: No supported adapters detected Why isn't the driver finding my video card? I have a hunch it has something to do with the fact that it's an AGP video card. Here is the output of lspci -v (why does it say Kernel driver in use: fglrx_pci?): 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV730 Pro AGP [Radeon HD 4600 Series] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices [AMD] nee ATI Device 0028 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at e0000000 (32-bit, prefetchable) [size=256M] I/O ports at de00 [size=256] Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Capabilities: [58] AGP version 3.0 Kernel driver in use: fglrx_pci

  Read the article

• Corsair SSD appears completely blank and does not retain written data

  - by ebanders

  I have a 180GB Corsair SSD (model# CSSD-F180GB2-BRKT) as the primary drive in a Windows laptop. Recently the machine became unbootable after installing Windows updates. Windows installed updates before the machine shut down and the next time the machine boot up it complained about not being able to find a bootable device. After finding fixmbr unsuccessful at making the machine unbootable, I investigated a little within knoppix. Fdisk revealed an empty partition table. A scan by Testdisk came up empty. And finally 'head -c 1024 | hd' reveals all zeros. Creating a primary partition spanning the whole disk completes successfully, but after a reboot the disk appears empty again. dmesg reveals no read or write errors. smartctl indicates that the drive is healthy- although the SMART attribute values do not appear to be read properly. "Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO" and "Threshold Page | INCONSISTENT IDENTITIES IN THE DATA" messages appear within the table of values. I don't have much experience with SSDs. Is this drive dead or something? Can anyone recommend any diagnostic tools that may be suited for diagnosing SSDs?

  Read the article

• How to connect android client to the localhost of Apache server (php) inside my laptop?

  - by user1796310

  I'm trying to create android apps which able sending data through wifi connection to my laptop Apache Server and MySQL database. I use the samsung galaxy tab 10.1 as my mobile device. and the protocol i used is HttpGet or HttpPost. And i use XAMPP( with Apache& SQL) to do the server and process the php. But, due to android cannot detect adhoc network from laptop, i use Virtual Router ( for window 7) to create virtual access point and make the tablet able connect to my laptop. But the problem is: [1] in my apps (client-android), where the httpget or httppost to which url? localhost in my laptop- 127.0.0.1 or localhost in android 10.0.0.1? or the ip address of the virtual router? [2]so, if i want access from android to the localhost(laptop-Apache) to call the php to run? which port? which ip address /url that i need to put in android apps(httpget)? and do i need to modify anything in httpconfig for XAMPP? thanks alot.

  Read the article

• Ubuntu's garbage collection cron job for PHP sessions takes 25 minutes to run, why?

  - by Lamah

  Ubuntu has a cron job set up which looks for and deletes old PHP sessions: # Look for and purge old sessions every 30 minutes 09,39 * * * * root [ -x /usr/lib/php5/maxlifetime ] \ && [ -d /var/lib/php5 ] && find /var/lib/php5/ -depth -mindepth 1 \ -maxdepth 1 -type f -cmin +$(/usr/lib/php5/maxlifetime) ! -execdir \ fuser -s {} 2> /dev/null \; -delete My problem is that this process is taking a very long time to run, with lots of disk IO. Here's my CPU usage graph: The cleanup running is represented by the teal spikes. At the beginning of the period, PHP's cleanup jobs were scheduled at the default 09 and 39 minutes times. At 15:00 I removed the 39 minute time from cron, so a cleanup job twice the size runs half as often (you can see the peaks get twice as wide and half as frequent). Here are the corresponding graphs for IO time: And disk operations: At the peak where there were about 14,000 sessions active, the cleanup can be seen to run for a full 25 minutes, apparently using 100% of one core of the CPU and what seems to be 100% of the disk IO for the entire period. Why is it so resource intensive? An ls of the session directory /var/lib/php5 takes just a fraction of a second. So why does it take a full 25 minutes to trim old sessions? Is there anything I can do to speed this up? The filesystem for this device is currently ext4, running on Ubuntu Precise 12.04 64-bit. EDIT: I suspect that the load is due to the unusual process "fuser" (since I expect a simple rm to be a damn sight faster than the performance I'm seeing). I'm going to remove the use of fuser and see what happens.

  Read the article

• Is it possible to add a WiFi HotSpot to an already established LAN, keep the two separate, and not modify the primary router?

  - by user12844

  I have a set up where my Cisco ASA is sitting in one facility, providing access to the Internet for two buildings. The two buildings are geographically separated by a Wireless Bridge spanning about 10 miles. All computers and equipment inside the LAN are on the same subnet (its pretty small) and we have WiFi AP's in both locations providing Wired and Wireless access to the LAN. Given all the BYOD (Ipods, and SmartPhones etc...) coming into the office as well as Visiting reps etc... we would like to also provide a non-secure, device independent (the devices cannot see or communicate with each other), and LAN independent (the devices cannot see or use anything on the LAN) HotSpot that anyone could use for their Devices that gives them access to the Internet ONLY without needing a password. I get that this could be possible at the facility with my Cisco if I messed with it and created VLANs etc... but then I would need to get it across my Bridge as well and don't think that would be possible without serious reconfiguration of everything. Would really like some kind of magic drop in solution that can kind of piggy back on my LAN without really needing to do very many if any changes to the current set up.

  Read the article

• How to set up multiple video cards in Windows XP

  - by Swish

  All I am trying to do is run a three monitor setup, two widescreens on the good card at high res and a third smaller monitor at 1024x768 that I watch continuously updating info in. I have a Dell Vostro 200 with an HIS Radeon HD 4670 video card in the PCI-e slot. I need an additional video card that will work in an available PCI slot. I Had a Nvidia GeForce 5200 that was installed but due to what I'm assuming was a compatible driver issue (because it was Nvidia not ATI) it wouldn't run at more than 640x480 4bit color when installed simultaneously with the HIS card. Previously I used the Nvidia with the onboard Intel video to run a third monitor, but now that the HSI uses PCI-e the onboard has to be disabled. I tried a Radeon 9200 PCI card that I found (microsoft made I think) with it and only that or the HIS card could be enabled at the same time. When both were in the HIS card said "The device cannot start". SO, based on the fact that I got the Nvidia to work (although very poorly) with the new HIS Radeon HD 4670 PCI-e I know it's possible, just don't know what type of card I need to use. Any ideas?

  Read the article

• Troubleshoot port forwarding. Could it be ISP blocking incoming connections?

  - by Gravy

  Had a new Axis IP camera delivered yesterday. Plugged into Cisco E2400 Wireless Router but having problems. Example topology: WAN IP: 10.10.10.10 (example) Cisco Router: 192.168.1.1 Axis Camera: 192.168.1.10:80 Port forwarding rules set up on router External Port: 999 Internal Port: 80 Protocol: TCP & UDP Device IP: 192.168.1.10:80 Enabled: True Trying to connect from within the lan to 192.168.1.1:80 from within browser - Works properly. Trying to connect from within the lan to 10:10:10:10:999 from within browser - Works properly. Trying to connect from outside the LAN (e.g. via 3g or another isp) to 10:10:10:10:999 from within browser - Doesnt work. I get the following errors from different machines / browsers: Safari could not open the page because the server stopped responding (IOS) The server at xx.xx.xx.xx is taking too long to respond. (firefox) This problem is not just for the Axis camera. I am also having similar problems connecting to my NAS drive. After using a web based port scanning tool, it appears as though port 999 is closed. Not certain why when I have set up port forwarding within the router. Any troubleshooting suggestions to help me determine whether the problem is with my Cisco settings / firewall or whether it could be my ISP blocking incoming connection requests? Many thanks

  Read the article

• Route all traffic of home network through VPN

  - by user436118

  I have a typical semi advanced home network scenario: A cable modem - eth A wireless router (netgear n600) eth and wlan A home server (Running ubuntu 12.04 LTS, connected over wlan) A bunch of wireless clients (wlan) Lying around I have anoher cheaper wlan router, and two different USB wlan NIC's that are known to work with Linux. ACTA struck. I want to route ALL of my WAN traffic through a remote server through a VPN. For sake of completition, lets say there is a remote server running debian sqeeze where a VPN server is to be installed. The network is then to behave so that if the VPN is not operative, it is separated from the outside world. I am familiar with general system/network practices, but lack the specific detailed knowledge to accomplish this. Please suggest the right approach, packages and configurations you'd use to reach said solution. I've also envisioned the following network configuration, please improve it if you see fit: ==LAN== Client ip:10.1.1.x nm:255.0.0.0 gw:10.1.1.1 reached via WLAN Wlan router 1: ip: 10.1.1.1 nm:255.0.0.0 gw: 10.10.10.1 reached via ETH Homeserver: <<< VPN is initiated here, and the other endpoint is somewhere on the internet. eth0: ip:10.10.10.1 nm: 0.0.0.0 gw:192.168.0.1 reached via WLAN Homeserver: wlan0: ip: 192.168.0.2 nm: 255.255.255.0 gw: 192.168.0.1 reached via WLAN ==WAN== Wlan router 2: ip: 192.168.0.1 nm: 0.0.0.0 gw: set via dhcp uplink connector: cable modem Cable Modem: Remote DHCP. Has on-board DHCP server for ethernet device that connects to it, and only works this way. All this WLAN fussery is because my home server is located in a part of the house where a cable link isnt possible unfortunately.

  Read the article

• How to run a restricted set of programs with Administrator privileges without giving up Admin acces (Win7 Pro)

  - by frLich

  I have a shared system, running Windows7 X64, restricted to a 'standard user' with no password. Not everyone who has access to the system has the administrator password. This works rather well, except for some applications - specially the unlock-applications for encrypted hard drives/USB flash drives. The specific ones either require Administrator access (eg. Seagate Blackarmor) or simply fail without it -- since these programs are sending raw commands to a device, this is to be expected. I would like to be able to add the hashes of these particular programs to a whitelist, and have them run as administrator without needing any prompts. Since these are by definition on removable media, I can't simply use a filename or even a path. One of the users who shares the system can be considered 'crafty', so anything which temporarily grants administrator rights to an user account is certain to cause problems. What i'd like to be able to do: 1) Create an admin account that can only run programs from a whitelist (or, failing that, from a directory) I can't find a good way to do this: As far as I can tell, SRP applies equally to ALL users? Even if I put a "Deny" token on all directories on the system, such that new directories would inherit it, it could still potentially run things from the mounted USB devices. I also don't know whether it's possible to create a new directory that DOESN'T inherit from the parent, that would lake the deny token, and provide admin access. 2) Find a lightweight service that will run these programs in its local context Windows7 seems to block cross-privilege level communication by default, and I haven't found such for windows 7. One example seems to be "sudo" (http://pages.cpsc.ucalgary.ca/~nfriess/sudo/) but because it uses a WLNOTIFY hook, it won't work under Vista nor Windows7 Non-Solutions: - RunAs: Requires administrator password! (but everyone calls it "sudo" anyway) - SuRun: From Google: "Surun uses its own Windows service that adds the user to the group of administrators during program start and removes him automatically from that group again"

  Read the article

• Google Chrome on Linux not using ALSA for sound

  - by DarkMoon

  On my laptop, I've got an .asoundrc file that outputs sound to my USB headset. This works fine for SMplayer and Firefox. However, Google Chrome (at least, Flash-based and HTML5-based videos and HTML5-based audio in Chrome) plays through the laptop speakers instead. I've tried running Chrome from a command-line, hoping there would be some helpful output, but no such luck. I've tried looking through Google for whether Chrome even uses ALSA, or if it uses something else, but I have been unsuccessful in this. This question seems to be the same issue, but no suggestion was made. Anyone have any ideas? I'm running Gentoo with a 3.10.17 kernel, 1.0.27 ALSA utils, 2.6.5 FVWM, and 36.0.1985.143 Chrome. If you need more info, please let me know. EDIT: I've configured the USB headset as the default ALSA device. Volume levels for both headset and onboard are set and un-muted using alsamixer. My .asoundrc file is as follows. ctl.!default { type hw card Headset } pcm.dmixer { type dmix ipc_key 1024 slave { pcm { type hw card Headset } period_size 1024 buffer_size 4096 } bindings { 0 0 1 1 } } pcm.!default { type plug slave.pcm dmixer }

  Read the article

• Debian - Problems Unmounting External Hard Drives

  - by user331981

  I recently installed Debian Testing on a new laptop and I just noticed that I am having some issues with unmounting external hard drives. I am using Mate Desktop 1.8.1. With the 1st drive, if I right click on the drive and select “safely remove”: The drive unmounts, spins down, immediately spins back up an remounts. Unable to unmount. With the 2nd drive, if I right click on the drive and select “safely remove”: The drive unmounts but does not spin down. With the 3rd drive, if I right click on the drive and select “safely remove”: The drive unmounts but does not spin down, immediately spins back up but does not remount, and after 20 seconds, it spins down and stays that way. Behavior is the same on both USB 2.0 and USB 3.0 ports. On my last laptop, on which I also used Debian Testing + Mate desktop, the safe removal of drives worked out of the box and I never had an issue with it. The drives would unmount, spin down and stay that way. To remount the drive, one needed to unplug the device and plug it back in. I am unsure how to troubleshoot this issue and I am not sure if it is merely a matter of installing a “missing” package of editing a config file. Thank you in advance.

  Read the article

• Driver corruption when deploying Dell Touchpad Drivers (with software) during imaging process

  - by BigHomie

  We're an sccm shop, and use it to deploy Windows. When deploying Dell laptops (multiple models), the touchpad drivers seem install properly, but the software doesn't. The resulting problem is that when the touchpad is pressed on occasion, the mouse pointer will 'jump' to certain points on the screen. A possible symptom of this problem/visible sign is if the touchpad icon isn't in the system tray. The software is in the control panel, but when opened part of the gui is pixelated, indicating botched install maybe? The manual resolution to this, is to go into device manager and uninstall the driver with the option to uninstall all driver software. After a restart, the driver and software is apparently reinstalled, and from there works as expected. Obviously this partially defeats the purpose of a zero touch deployment. If anyone knows why this is and/or a possible workaround, those answers would be valid as well. Barring that, I want to find a way to deploy the driver and touchpad software in an unattended way, so that it can be conditionally installing during the imaging process. To be honest I'm not sure how to troubleshoot this, I suppose I could try drvinst.exe to install the driver, but finding out why this fails initially would keep me from spinning my wheels.

  Read the article

• phpMyadmin issue on cpanel

  - by user1149244

  I logged in into our cpanel to view phpMyAdmin but I can't open it. It give me this error message: Warning: session_write_close() [function.session-write-close]: write failed: No space left on device (28) in /usr/local/cpanel/base/3rdparty/phpMyAdmin/index.php on line 42 Warning: session_write_close() [function.session-write-close]: Failed to write session data (files). Please verify that the current setting of session.save_path is correct (/var/cpanel/userhomes/cpanelphpmyadmin/sessions) in /usr/local/cpanel/base/3rdparty/phpMyAdmin/index.php on line 42 Warning: Cannot modify header information - headers already sent by (output started at /usr/local/cpanel/base/3rdparty/phpMyAdmin/index.php:42) in /usr/local/cpanel/base/3rdparty/phpMyAdmin/index.php on line 99 I contacted the support to assist me with. They just told me that the server is unmanaged. They told me to delete the free the partition but I don't know how to do it. I'm noob on that matter. The /var/log/btmp is over 8GB as they said. I want to delete that file. How would I do this? I need to free the space of the partition. I need some steps on how to do it and also steps on how to delete the /var/log/btmp. I have been googling around but I haven't found anything.

  Read the article

• Why is /dev/urandom only readable by root since Ubuntu 12.04 and how can I "fix" it?

  - by Joe Hopfgartner

  I used to work with Ubuntu 10.04 templates on a lot of servers. Since changing to 12.04 I have problems that I've now isolated. The /dev/urandom device is only accessible to root. This caused SSL engines, at least in PHP, for example file_get_contents(https://... to fail. It also broke redmine. After a chmod 644 it works fine, but that doesnt stay upon reboot. So my question. why is this? I see no security risk because... i mean.. wanna steal some random data? How can I "fix" it? The servers are isolated and used by only one application, thats why I use openvz. I think about something like a runlevel script or so... but how do I do it efficiently? Maby with dpkg or apt? The same goes vor /dev/shm. in this case i totally understand why its not accessible, but I assume I can "fix" it the same way to fix /dev/urandom

  Read the article

• How to fix missing RAID1 drive

  - by Sodved

  I had to do some fiddling about with my cables inside thebox and now I am getting a "Critical Error" about the RAID disks during startup. I have a gigabyte GA-MA770T-UD3 motherboard. Aparently the RAID controller is an AMD SB710 chip. I'm pretty sure I know what happenned. The first time I rebooted I had forgotten the power cable on one of the disks in the RAID1 (mirror) and let it boot up. So I shut down and put the power back in. So now when it boots up I go into the RAID admin interface (between the BIOS screen and the OS loading): it shows the RAID1 as in error the logical device has one disk and says the other is disconnected or missing the other physical disk shows up as a single disk If I boot to the OS (Windows 7 32 bit) the data all seems to be there. If I go into computer management it says my partition is on a disk and working OK. But the other disk is offline because: "The disk is offline because it has a signature collision with another disk that is online" So I am guessing because I STUPIDLY booted up with only one of the disks powered on, the other disk fell out of synch with the mirror and so now cannot rejoin the mirror. How do I fix this? I want to get the RAID1 mirror working again. There does not appear to be any "Repair" option in the basic RAID admin tool which I get into during startup before the OS boots. I have not made any explicit changes to the online one (but I guess the OS has probably written some admin data).

  Read the article

• different user group can not upload file in the server

  - by Dallal

  I have a CentOS server running in Thailand, and I'm in Canada. The guy at the computer center who set up the server for me doesn't really understand much about linux and left me off an issue to solve myself. I just moved from Mac Server to Linux server, and the first thing I'm facing a problem now is `file name` has failed to upload due to an error The uploaded file could not be moved to `location name` So what happen is that I knew from my experiences of these problem is all about permissions. So I go ahead and checked on my whole folder and found that everything in the folder permission is like myusername mygroupname then I checked the httpd file in the server and it is default to apache apache. My question is that how can I make my user to be in the same group with apache group so that I don't have to have any problem about uploading, changing data in my file....? But without having to affect other user in the same server. I'm holding Administrator account, but not root account, but I can change stuff on the server root no problem. When I was with godaddy.com there never been any problem about the permission and I wish I know how they configure that :(

  Read the article

• Route all traffic of home network through VPN [migrated]

  - by user436118

  I have a typical semi advanced home network scenario: A cable modem - eth A wireless router (netgear n600) eth and wlan A home server (Running ubuntu 12.04 LTS, connected over wlan) A bunch of wireless clients (wlan) Lying around I have anoher cheaper wlan router, and two different USB wlan NIC's that are known to work with Linux. ACTA struck. I want to route ALL of my WAN traffic through a remote server through a VPN. For sake of completition, lets say there is a remote server running debian sqeeze where a VPN server is to be installed. The network is then to behave so that if the VPN is not operative, it is separated from the outside world. I am familiar with general system/network practices, but lack the specific detailed knowledge to accomplish this. Please suggest the right approach, packages and configurations you'd use to reach said solution. I've also envisioned the following network configuration, please improve it if you see fit: Client ip:10.1.1.x nm:255.0.0.0 gw:10.1.1.1 reached via WLAN Wlan router 1: ip: 10.1.1.1 nm:255.0.0.0 gw: 10.10.10.1 reached via ETH Homeserver: <<< VPN is initiated here, and the other endpoint is somewhere on the internet. eth0: ip:10.10.10.1 nm: 0.0.0.0 gw:192.168.0.1 reached via WLAN Homeserver: wlan0: ip: 192.168.0.2 nm: 255.255.255.0 gw: 192.168.0.1 reached via WLAN Wlan router 2: ip: 192.168.0.1 nm: 0.0.0.0 gw: set via dhcp uplink connector: cable modem Cable Modem: Remote DHCP. Has on-board DHCP server for ethernet device that connects to it, and only works this way. All this WLAN fussery is because my home server is located in a part of the house where a cable link isnt possible unfortunately.

  Read the article

< Previous Page | 551 552 553 554 555 556 557 558 559 560 561 562  | Next Page >