Search Results

Search found 2503 results on 101 pages for 'destination'.

Page 57/101 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

• Squid3 not working. Access denied.

  - by Nitish

  I installed SQUID3 on a Linux machine with two ethernet interfaces (eth0 and eth1). I used the default settings in the squid.conf file and uncommented the two lines acl localnet src 192.168.0.0/16 and http_access allow localnet. eth0 is connected to a router, which provides Internet access. It is assigned an IP 192.168.1.2 by the router. I manually configured eth1 to have an IP address 192.168.5.1. It is connected to a switch. Systems having IP addresses 192.168.5.x are connected to this switch. I ran these two commands for NAT: iptables -t nat -A PREROUTING -i eth1 -p tcp -m tcp --dport 80 -j DNAT --to-destination 192.168.5.1:3128 iptables -t nat -A PREROUTING -i eth0 -p tcp -m tcp --dport 80 -j REDIRECT --to-ports 3128 But when I try to access internet from a system having IP 192.168.5.2 through the proxy I get an error that says "Access denied". What is wrong with my configuration?

  Read the article

• How to access vm inside a vm via VNC?

  - by can.

  For some reasons I installed virtual machines inside a virtual machine, like this: A( B( C )) where A is the physical machine, B is a vm and the network type is NAT. And C is also a virtual machine and the network type is bridged. The OSes are Ubuntu 12.04 and the hypervisors are kvm. I can access B via VNC and via ssh from A, but for C I can't use ssh because C has no IP address at the start. And I assume I can only access C via VNC. I tried something like(on A): iptables -t nat -A PREROUTING -d $ip-of-A -p tcp --dport 6500 -j DNAT --to-destination $ip-of-B:5900 (I referred to this) But it doesn't work. And I'm reading the man pages of iptables and hope someone could help :)

  Read the article

• How to stop live network traffic displayed in terminal?

  - by Jakobud

  For our network we are working on building a new firewall box and we just installed Smoothwall on it to test it out. When I start up the box, before the login prompt even appears, all of the live IP traffic is appearing in the terminal (source/destination IPs, MACs, Ports, etc). I wait for the boot sequence to finish, but all I see is this IP traffic. The login prompt never comes up. I finally get sick of waiting and press CTRL + C and it says "Entering Run Level 3" and then I get a login prompt finally. Once I login, the IP traffic continues to fly through the terminal even as I'm trying to type commands. How do I turn this stuff off? Is this the default setting for Smoothwall to have all this IP traffic going by on the screen? It essentially renders using the terminal to being useless.

  Read the article

• Sun OS 5.10 not honoring .hushlogin

  - by nixomose

  I scp and ssh a zillion times a day, and because of our corporate policy I can't get rid of /etc/issue or /etc/motd on the destination machines. So whereas I just want to see the results of my scp or ssh, all I ever end up seeing is thousands of copies of the motd. .hushlogin doesn't seem to be honored. Any other ideas on how to get rid of the message display? Is there some sshd config setting I don't know about (though I probably couldn't change that either)? Is there some curiously sunos/solaris specific way to achieve the goal?

  Read the article

• How to avoid Remove-Item PowerShell errors "process cannot access the file"?

  - by Michael Freidgeim

  We are using TfsDeployer and PowerShell script to remove the folders ising Remove-Item before deployment of a new version. Sometimes the PS script failed with the error Remove-Item : Cannot remove item Services\bin: The process cannot access the file Services\bin' because it is being used by another proc Get-ChildItem -Path $Destination -Recurse | Remove-Item <<<< -force -recurse + CategoryInfo : WriteError: (C:\Program File..\Services\bin:DirectoryInfo) [Remove-Item], IOException FullyQualifiedErrorId : RemoveFileSystemItemIOError,Microsoft.PowerShell.Commands.RemoveItemCommand I’ve tried to follow the answer from PowerShell remove force to pipe get-childitem -recurse into remove-item. get-childitem * -include *.csv -recurse | remove-item ,but the error still happens periodically. We are using unlocker to manually kill locking application, (it’s usually w3wp), but I prefer to find automated solution. Another (not ideal) option is to-suppress-powershell-errors get-childitem -recurse -force -erroraction silentlycontinue Any suggestions are welcome.

  Read the article

• Can't get port forwarding to work on Ubuntu

  - by Znarkus

  I'm using my home server as NAT/router, which works well. But now I'm trying to forward port 3478, which I can't get to work. eth0 = public interface eth1 = private network $ cat /proc/sys/net/ipv4/conf/eth0/forwarding 1 $ cat /proc/sys/net/ipv4/conf/eth1/forwarding 1 Then to forward port 3478 to 10.0.0.7, I read somewhere that I should run iptables -t nat -A PREROUTING -p tcp -i eth0 --dport 3478 -j DNAT --to-destination 10.0.0.7:3478 iptables -A FORWARD -p tcp -d 10.0.0.7 --dport 3478 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT I also ran ufw allow 3478 But testing port 3478 with http://www.canyouseeme.org/ doesn't work. Any idea what I have done wrong?

  Read the article

• Outlook 2003 won't send mail

  - by RKid

  A colleague's e-mail has just started playing up - he's using Outlook/Office 2003 on a Win XP SP3 machine. Yesterday his mail has suddenly stopped being received, although there are no errors of any kind that i can see. It was only noticed because he didn't have any replys all day. His e-mails seem to send fine - no errors come up, the mail goes into Sent Items as usual, but it never arrives at it's destination. However, when mail is sent from Outlook Web Access, e-mails send fine. All connections to the server appear fine and outlook is 'connected' but I've had a look at the message tracking on our Exchange 2003 server and no messages are appearing when sent from outlook, only when sent through OWA. Where should i be looking ? Thanks.

  Read the article

• How can I use rsync with a FAT file system?

  - by Kim

  I would like to write a simple backup script that saves some data to a FAT drive. Should I reformat the drive and use a better file system or is it possible to use rsync with FAT? If so, what problems might I run into? Would performance be a lot worse? EDIT: This is on linux, didn't even know there was a rsync for windows. The sources are various file systems (it's a mess), and the destination is currently formatted with FAT32. Thank you for your answers, I'll probably go for a reformat, since I'm not completely sure about the file sizes we'll have.

  Read the article

• PostgreSQL, update existing rows with pg_restore

  - by woky

  Hello. I need to sync two PostgreSQL databases (some tables from development db to production db) sometimes. So I came up with this script: [...] pg_dump -a -F tar -t table1 -t table2 -U user1 dbname1 | \ pg_restore -a -U user2 -d dbname2 [...] The problem is that this works just for newly added rows. When I edit non-PK column I get constraint error and row isn't updated. For each dumped row I need to check if it exists in destination database (by PK) and if so delete it before INSERT/COPY. Thanks for your advice. (Previously posted on stackoverflow.com, but IMHO this is better place for this question).

  Read the article

• OpenBSD: Gateway outside subnet (works in Linux)

  - by kshade

  We need to set up an OpenBSD host to use a default gateway that's outside of it's subnet. This is all I need to do on Linux (not the actual IPs) to achieve it: ifconfig eth0 33.33.33.33/31 up route add 33.33.33.254 dev eth0 route add default gw 33.33.33.254 The problem is that we don't know the proper equivalent of the middle command in OpenBSD. The man page says: If the destination is directly reachable via an interface requiring no intermediary system to act as a gateway, the -iface modifier should be specified; Sadly we can't seem to figure out how to make it work with that. This is a virtual host on an OVH server, they have documentation for many other operating systems showing how to do it here: http://help.ovh.co.uk/BridgeClient

  Read the article

• RDC not working from outside

  - by Cotten

  I've set up Remote Connection according to : http://windows.microsoft.com/is-IS/windows7/allow-remote-desktop-connections-from-outside-your-home-network That is, Allow remote connections to the computer you want to access. Make sure Remote Desktop is able to communicate through your firewall. Find the IP address of the computer on your home network that you want to connect to. Open your router's configuration screen and forward TCP port 3389 to the destination computer's IP address. Find your router's public IP address so that Remote Desktop can find it on the Internet. When I'm inside the LAN, RDC works flawlessly. When I try to connect to the ip given by my ISP it cannot connect. I've setup port forwarding for 3389 on my netgear router. Thanks!

  Read the article

• how to communicate in typical router switch router scenario?

  - by Kossel

  I'm learning routing using packet tracer simulation and I think this is a very commun scenario: let's say pc4 is the server... why I can't ping from PC1 to 192.168.2.253 (router1) but I can ping 192.168.2.2 (pc0) aren't they the same subnet? what am I missing or have to do in order to reach pc4? (192.168.100.254) from pc 1 (192.168.1.1) is there something like "default gateway" for router? thanks for advice PS: during the simulation it shows error "The routing table does not have a route to the destination IP address. The router drops the packe (from 192.168.2.253 to 192.168.1.1)"

  Read the article

• How to set up a subdomain in nsd3

  - by qliq

  nsd3 is very little-known but super-lightweight and stable DNS server which makes it a great alternative to bind9 be used on low-end boxes. There is a very good tutorial here that describe how to set it up. My problem is that I need to set up a subdomain subd1.example.com that will be severed on another VPS. I tried to add subdmn1.mymaindomain.com. IN 1.2.3.5 (Assuming that my destination IP is 1.2.3.5) Then I nsdc rebuild service nsd3 restart However the subdmn1.mymaindomain.com fails to resolve to the IP. Any clues will be much appreciated.

  Read the article

• Reducing storage cost by moving old files to external USB HDDs. Your thoughts?

  - by cparker4486

  I've got about 300GB of pictures and marketing data that is rarely accessed and I'd like to get it off my main storage. I was thinking to simply add two external USB HDDs to the server and move all the files to one of the drives. The second drive would be the backup destination for the first drive. I'm working with Server 2003 R2 SP2. This will help me free a good amount of space on my main storage as well as reduce the complexity, backup window, and usage of my backups to tape.

  Read the article

• Smoothwall: How to stop live network traffic displayed in terminal?

  - by Jakobud

  For our network we are working on building a new firewall box and we just installed Smoothwall on it to test it out. When I start up the box, before the login prompt even appears, all of the live IP traffic is appearing in the terminal (source/destination IPs, MACs, Ports, etc). I wait for the boot sequence to finish, but all I see is this IP traffic. The login prompt never comes up. I finally get sick of waiting and press CTRL + C and it says "Entering Run Level 3" and then I get a login prompt finally. Once I login, the IP traffic continues to fly through the terminal even as I'm trying to type commands. How do I turn this stuff off? Is this the default setting for Smoothwall to have all this IP traffic going by on the screen? It essentially renders using the terminal to being useless.

  Read the article

• Snort monitoring of spanning interface

  - by aHunter

  I have configured a Cisco 3500 switch with a port SPAN and have my snort node (fedora 13) plugged into it. I am running snort as a daemon and have configured a rule to log all tcp traffic but I am only seeing traffic with a destination of the snort node. I know that the SPAN port is working and wanted to know if there is a specific option that I needed to start snort with in order for it to pickup all the traffic? Or is there something that I have missed here? Many thanks.

  Read the article

• How to forbid postfix to send to external domains [closed]

  - by elhoim

  I have a local postfix server, and i want it to only relay emails to the only local domain (localdomain.be): myhostname = localdomain.be mydomain = localdomain.be alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases myorigin = $myhostname mydestination = $myhostname relay_domains = $mydomain default_transport = smtp relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 10.0.0.0/24 mailbox_size_limit = 64000000 message_size_limit = 1000000 recipient_delimiter = + inet_interfaces = all inet_protocols = all smtp_host_lookup = native This configuration works fine to allow relay mail locally and on external destination domains, but i would like it to be an impossibility to send to other domains (ie: gmail.com). relay_domains is supposed to ensure that but it does not seem to really filter since i can still send to my gmail address.

  Read the article

• Internet connection resets (wifi), no device has wifi for moment

  - by Gizmo

  I have a few devices setup and I noticed this happens with both my old and new router (two different vendors&models) This happens occasionally, and I tried wireshark today and this cought my attention: No. Time Source Destination Protocol Length Info 69 6.464423000 LiteonTe_7f:64:30 Broadcast ARP 42 Who has 192.168.2.4? Tell 0.0.0.0 73 7.451146000 LiteonTe_59:65:94 Arcadyan_e1:8c:cf ARP 42 Who has 192.168.2.254? Tell 192.168.2.1 85 9.450443000 LiteonTe_59:65:94 Arcadyan_e1:8c:cf ARP 42 Who has 192.168.2.254? Tell 192.168.2.1 91 10.521000000 LiteonTe_59:65:94 Broadcast ARP 42 Who has 192.168.2.254? Tell 192.168.2.1 93 10.860953000 LiteonTe_7f:64:30 Broadcast ARP 42 Who has 192.168.2.254? Tell 192.168.2.4 97 11.099463000 LiteonTe_7f:64:30 Broadcast ARP 42 Who has 192.168.2.254? Tell 192.168.2.4 where 192.168.2.254 is the gateway/router, 192.168.2.1 my laptop ip and 192.168.2.4 my sisters laptop.. what's happening here?

  Read the article

• What are the methods of separating network spaces in a LAN?

  - by dash17291

  Please detail me the methods. My thoughts: put the servers in separate (sub)networks the servers are forced to go through the firewall but no NAT is required assign more IP addresses to the internal interface of the server choosing gateway addresses from the clients and servers IP address ranges split DNS Netfilter/{iptables, ipset} could be heavily involved, I'm talking about Linux servers. See for example: Destination NAT Onto the Same Network from internal clients Please do not explain what is NAT or DNS. This is a theoretical question, but my poor English knowledge prevent me to describe it in a fancy fashion.

  Read the article

• How do I map a friendly name (e.g. www.example.com) to 127.0.0.1:port# on Mac OS X

  - by Fred Finkle

  I am trying to create a demo for a class of mine and I want to configure "fake" domain names on my laptop. A previous question "Can I specify a port in an entry in my /etc/hosts on OS X?" contained an answer indicating that to do it you must use /etc/hosts plus changes to the iptables "If OS X uses iptables you could point xyz.com to some ip in the hosts file like 157.166.226.25 and then: sudo iptables -t nat -A OUTPUT -p tcp --dport 80 -d 157.166.226.25 -j DNAT --to-destination 127.0.0.1:3000 " Since OS X doesn't use iptables, how do I do the equivalent using the tools available on OS X? (the original "asker" seemed to know how to do this, so it wasn't explained). Thanks in advance.

  Read the article

• Chrome sending of packets to random destinations upon reconnect/disconnect

  - by f0x

  Noticed an interesting thing whilst debugging one of my websocket applications that Google Chrome will push out 3 http requests upon a network connection status changing; Quite disconcerting and looks almost as if some malware is checking out to a random server. I don't quite understand the why though since they all return a 502 or have no response code at all since the destination does not exist. On Disconnect: Reconnect: I guess the main question is this normal and what the use is; howcome they wouldn't go for a dns lookup that actually exists?

  Read the article

• Excluding four IP's from a /32 static route

  - by Justin

  I have a Cisco ASA routing a /32 of public addresses (non RFC-1812) through a private link. When the device sees the destination address it selects the private route instead of going out over the public network. This works great but I am now trying to exclude 4 IP's from the private route. Traffic to these addresses should go over the public internet instead of being routed over the private network. Can I just add anothe route for these four IP's or do I have to modify the existing route for the /32?

  Read the article

• Don't understand [0:0] iptable syntax

  - by artaxerxe

  I'm struggling with some iptables rules. I'm a newbie in iptables. I found some resources where I get the following command related to iptables. This is stored in a file that will be executed. [0:0] -A PREROUTING -s 10.1.0.0/24 -p tcp -m tcp --dport 81 -j DNAT --to-destination 10.1.0.6:3128 Can anybody explain me what does [0:0] mean? Also, some link related to this in iptables are welcome. Thanks in advance! P.S. If you need more rules, just let me know.

  Read the article

• How to create an rpm without a build step

  - by infra.user

  I'm trying to create an rpm of some code which doesn't need to be built. It will just need to run a script when it's installed on the destination system (i.e. I just need the %install portion of the spec file). I've left both %build and %configure sections of my rpm spec file empty, yet rpmbuild continues to try and execute ./configure with a bunch of parameters. Does anyone know how I can have rpmbuild create the rpm without trying to run ./configure? Thanks.

  Read the article

• How can I push a git repository to a folder over SSH?

  - by Rich

  I have a folder called my-project inside which I've done git init, git commit -a, etc. Now I want to push it to an empty folder at /mnt/foo/bar on a remote server. How can I do this? I did try, based on what I'd read: cd my-project git remote add origin ssh://user@host/mnt/foo/bar/my-project.git git push origin master which didn't seem right (I'd assume source would come before destination) and it failed: fatal: '/mnt/boxee/git/midwinter-physiotherapy.git' does not appear to be a git repository fatal: The remote end hung up unexpectedly I'd like this to work such that I don't have to access the remote host and manually init a git repository every time ... do I have to do that? Am I going down the right route at all? Thanks.

  Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >