Search Results

Search found 2316 results on 93 pages for 'cmd'.

Page 59/93 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

• External usb 3.0 hard drive is not recognised when plugged into usb 3 port (ubuntu natty 64 bit).

  - by kimangroo

  I have an Iomega Prestige Portable External Hard Drive 1TB USB 3.0. It works fine on windows 7 as a usb 3.0 drive. It isn't detected on ubuntu natty 64bit, 2.6.38-8-generic. fdisk -l cannot see it at all: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x1bed746b Device Boot Start End Blocks Id System /dev/sda1 1 1689 13560832 27 Unknown /dev/sda2 * 1689 1702 102400 7 HPFS/NTFS /dev/sda3 1702 19978 146805760 7 HPFS/NTFS /dev/sda4 19978 60802 327914497 5 Extended /dev/sda5 25555 60802 283120640 7 HPFS/NTFS /dev/sda6 19978 23909 31571968 83 Linux /dev/sda7 23909 25555 13218816 82 Linux swap / Solaris Partition table entries are not in disk order lsusb can see it: Bus 003 Device 003: ID 059b:0070 Iomega Corp. Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 002 Device 004: ID 05fe:0011 Chic Technology Corp. Browser Mouse Bus 002 Device 003: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode) Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device 005: ID 0489:e00f Foxconn / Hon Hai Bus 001 Device 004: ID 0c45:64b5 Microdia Bus 001 Device 003: ID 08ff:168f AuthenTec, Inc. Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub And dmesg | grep -i xhci (I may have unplugged the drive and plugged it back in again after booting): [ 1.659060] pci 0000:04:00.0: xHCI HW did not halt within 2000 usec status = 0x0 [ 11.484971] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 11.484997] xhci_hcd 0000:04:00.0: setting latency timer to 64 [ 11.485002] xhci_hcd 0000:04:00.0: xHCI Host Controller [ 11.485064] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 [ 11.636149] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 [ 11.636241] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X [ 11.636246] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X [ 11.636251] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X [ 11.636256] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X [ 11.636261] xhci_hcd 0000:04:00.0: irq 47 for MSI/MSI-X [ 11.639654] xHCI xhci_add_endpoint called for root hub [ 11.639655] xHCI xhci_check_bandwidth called for root hub [ 11.956366] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 2 [ 12.001073] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.007059] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.012932] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.018922] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.049139] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.056754] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.131607] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 12.179717] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 12.686876] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 12.687058] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 12.687152] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 43.330737] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 2 [ 43.422579] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 43.422658] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af00 [ 43.422665] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af40 [ 43.422671] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669af80 [ 43.422677] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff88014669afc0 [ 43.531159] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 125.160248] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.766466] usb 3-1: new SuperSpeed USB device using xhci_hcd and address 3 [ 903.807789] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.813530] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.819400] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.825104] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.855067] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862314] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 903.862597] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst [ 903.913211] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 904.424416] xhci_hcd 0000:04:00.0: WARN: babble error on endpoint [ 904.424599] xhci_hcd 0000:04:00.0: WARN Set TR Deq Ptr cmd invalid because of stream ID configuration [ 904.424700] xhci_hcd 0000:04:00.0: ERROR Transfer event for disabled endpoint or incorrect stream ring [ 935.139021] usb 3-1: reset SuperSpeed USB device using xhci_hcd and address 3 [ 935.226075] xhci_hcd 0000:04:00.0: WARN: short transfer on control ep [ 935.226140] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b00 [ 935.226148] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b40 [ 935.226153] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186b80 [ 935.226159] xhci_hcd 0000:04:00.0: xHCI xhci_drop_endpoint called with disabled ep ffff880148186bc0 [ 935.343339] xhci_hcd 0000:04:00.0: WARN no SS endpoint bMaxBurst I thought it might be that the firmware wasn't compatible with linux or something, but when booting a live image of partedmagic, (2.6.38.4-pmagic), the drive was detected fine, I could mount it and got usb 3.0 speeds (at least they double the speeds I got from plugging same drive in usb 2 ports). dmesg in partedmagic did say something about no SuperSpeed endpoint which was an error I saw in a previous dmesg of ubuntu: Jun 27 15:49:02 (none) user.info kernel: [ 2.978743] xhci_hcd 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Jun 27 15:49:02 (none) user.debug kernel: [ 2.978771] xhci_hcd 0000:04:00.0: setting latency timer to 64 Jun 27 15:49:02 (none) user.info kernel: [ 2.978781] xhci_hcd 0000:04:00.0: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 2.978856] xhci_hcd 0000:04:00.0: new USB bus registered, assigned bus number 3 Jun 27 15:49:02 (none) user.info kernel: [ 3.089458] xhci_hcd 0000:04:00.0: irq 18, io mem 0xc5400000 Jun 27 15:49:02 (none) user.debug kernel: [ 3.089541] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089544] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089546] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089548] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X Jun 27 15:49:02 (none) user.debug kernel: [ 3.089550] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X Jun 27 15:49:02 (none) user.warn kernel: [ 3.092857] usb usb3: No SuperSpeed endpoint companion for config 1 interface 0 altsetting 0 ep 129: using minimum values Jun 27 15:49:02 (none) user.info kernel: [ 3.092864] usb usb3: New USB device found, idVendor=1d6b, idProduct=0003 Jun 27 15:49:02 (none) user.info kernel: [ 3.092866] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Jun 27 15:49:02 (none) user.info kernel: [ 3.092867] usb usb3: Product: xHCI Host Controller Jun 27 15:49:02 (none) user.info kernel: [ 3.092869] usb usb3: Manufacturer: Linux 2.6.38.4-pmagic xhci_hcd Jun 27 15:49:02 (none) user.info kernel: [ 3.092870] usb usb3: SerialNumber: 0000:04:00.0 Jun 27 15:49:02 (none) user.debug kernel: [ 3.092961] xHCI xhci_add_endpoint called for root hub Jun 27 15:49:02 (none) user.debug kernel: [ 3.092963] xHCI xhci_check_bandwidth called for root hub Well I have no idea what's going wrong, and I haven't had much luck from google and the forums so far. A number of unanswered threads with people with similar error messages and problems only. Hopefully someone here can help or point me in the right direction?!

  Read the article

• Consuming ASP.NET Web API services from PHP script

  - by DigiMortal

  I introduced ASP.NET Web API in some of my previous posts. Although Web API is easy to use in ASP.NET web applications you can use Web API also from other platforms. This post shows you how to consume ASP.NET Web API from PHP scripts. Here are my previous posts about Web API: How content negotiation works? ASP.NET Web API: Extending content negotiation with new formats Query string based content formatting Although these posts cover content negotiation they give you some idea about how Web API works. Test application On Web API side I use the same sample application as in previous Web API posts – very primitive web application to manage contacts. Listing contacts On the other machine I will run the following PHP script that works against my Web API application: <?php   // request list of contacts from Web API $json = file_get_contents('http://vs2010dev:3613/api/contacts/'); // deserialize data from JSON $contacts = json_decode($json); ?> <html> <head>     <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> </head> <body>     <table>     <?php      foreach($contacts as $contact)     {         ?>         <tr>             <td valign="top">                 <?php echo $contact->FirstName ?>             </td>             <td valign="top">                 <?php echo $contact->LastName ?>             </td>             <td valign="middle">                 <form method="POST">                     <input type="hidden" name="id"                          value="<?php echo $contact-/>Id ?>" />                     <input type="submit" name="cmd"                          value="Delete"/>                 </form>             </td>         </tr>         <?php     }     ?>     </table> </body> </html> Notice how easy it is to handle JSON data in PHP! My PHP script produces the following output: Looks like data is here as it should be. Deleting contacts Now let’s write code to delete contacts. Add this block of code before any other code in PHP script. if(@$_POST['cmd'] == 'Delete') {     $errno = 0;     $errstr = '';     $id = @$_POST['id'];          $params = array('http' => array(               'method' => 'DELETE',               'content' => ""             ));     $url = 'http://vs2010dev:3613/api/contacts/'.$id;     $ctx = stream_context_create($params);     $fp = fopen($url, 'rb', false, $ctx);       if (!$fp) {         $res = false;       } else {         $res = stream_get_contents($fp);       }     fclose($fp);     header('Location: /json.php');     exit; } Again simple code. If we write also insert and update methods we may want to bundle those operations to single class. Conclusion ASP.NET Web API is not only ASP.NET fun. It is available also for all other platforms. In this posting we wrote simple PHP client that is able to communicate with our Web API application. We wrote only some simple code, nothing complex. Same way we can use also platforms like Java, PERL and Ruby.

  Read the article

• Windows 7 - Local Area Connection Adapter is disabled

  - by teepusink

  Hi, I just got a Windows 7. However, I'm now unable to connect to the internet. Doing the diagnosis gives me these: 1. There might be a problem with the driver for the Local Area Connection Adapter 2. The Local Area Connection 2 Adapter is disabled How do I resolve those? These are what I've tried: 1. in cmd do ipconfig /renew 2. in device manager, go to network adapter. (I don't see any red exclamation marks) Thanks, Tee

  Read the article

• Why do I get Access Denied when using WinRM?

  - by Kev

  Following on from this question: Why does my PowerShell script hang when called in PSEXEC via a batch (.cmd) file? I took the advice from Jim B and installed WinRM. To recap I have two servers: HMon01 - runs Windows 2003 Standard SP2 Web1928 - runs Windows 2008 Standard SP2 Both servers are standalone. I installed WinRM for Windows 2003 from here and configured WinRM as follows on both machines: Client NetworkDelayms = 5000 URLPrefix = wsman AllowUnencrypted = false Auth Basic = true Digest = true Kerberos = true Negotiate = true Certificate = true DefaultPorts HTTP = 80 HTTPS = 443 TrustedHosts = * The problem I have is that if I remotely execute commands using the remote machine's built in Administrator account then all is well. However I have an account on the remote machine named remoteexec which is a member of the Administrators group (we disable our Administrator accounts). If I use this account then I get Access Denied errors. I've done all the usual things such as checking passwords and the like. Why would this be?

  Read the article

• TEMP_PART01 and C drive

  - by SmartLemon

  So we have a Samsung series 9 laptop and it has a 128 GB solid state drive, the problem we are having with it is that it has 4 partitions, one that's 100MB (who knows what for), one thats 40 GB (Primary Windows partition), 60 GB partition (TEMP_PART01) and a microsoft office one. The primary windows partition only has less than, 30 MB left, we want to increase this space, I know that I could just move everything to temp_part01 but we are not quite sure on it. What we are thinking of doing is deleting this partition all together and extending the windows volume. The problem is that the extra partition has 55.7 remaining out of 59.7 GB, which means there is something on it, but it shows up with nothing when we go into it, when we change the settings to show hidden files, but still nothing, I then used CMD to list all the files using dir d: and still no files. So would it be safe to delete it and extend the windows volume? Or what should I do? Here's a screen shot:

  Read the article

• WinSat command line closes too fast

  - by Rob Cowell

  I'm trying to do some analysis under Windows 7 as to why I can't get a Windows Experience Index (WEI) rating due to disk issues. To this end, I'm trying to run winsat from the command line with :- winsat disk -seq -read -drive c and winsat disk -ran -write -n 2 but the command window is closing too quickly to be able to read the results. I've tried opening a seperate cmd window to run it in but it still insists on launching its own window to run in, closing straight away. Any idea how I can see the output?

  Read the article

• Bring the windows of two different apps in mac os to the front?

  - by Nicolas Kokkalis

  How do I easily bring to the front of the screen the top windows of two different application in Mac OS X? I prefer to use the keyboard only. Example Scenario: Say there are 10 Firefox and 10 TextEdit windows open. Also, say that these windows are having various different sizes so that the windows of each application fully cover the desktop. Goal: I want to bring to the front of my screen the top window of Firefox along with the top window of TextEdit, so that I can visually compare some data. Restrictions: I cannot use expose (since having 20 windows on the screen already renders expose useless) And I do not want to use multiple desktop (too complex and time consuming) I prefer to use a keyboard shortcut. Unfortunately cmd+tab brings all windows of each application to the top, covering all windows of the other applications.

  Read the article

• How to configure mod_cluster, httpd, Jboss 7.1.1?

  - by user180157

  I am trying develop clustered environment in Jboss 7.1.1. For mod_cluster setup I have done the following steps. Downloaded httpd 2.4 placed @C:\Apache24 Placed below .so files in C:\Apache24\modules mod_proxy.so mod_proxy_ajp.so mod_slotmem.so mod_manager.so mod_proxy_cluster.so mod_advertise.so Using cmd, when I run C:\Apache24\bin: httpd.exe am getting below error and apache is not getting started. httpd.exe: Syntax error on line 528 of C:/Apache24/conf/httpd.conf: Cannot load modules/mod_slotmem.so into server: The specified procedure could not be found. Could anyone provide the solution? Thanks

  Read the article

• PSExec on Windows 2008 R2 Failing "Network name cannot be found"

  - by Adam Frisby

  Hi, We've got a bunch of remote admin scripts which rely on psexec and they do not appear to be working over the network on our new 2008 hosts. An error dump is below: C:\Users\<user>\Desktop\PsTools> psexec \\<host IP> -u Administrator -p <pass> <cmd> PsExec v1.97 - Execute processes remotely Copyright (C) 2001-2009 Mark Russinovich Sysinternals - www.sysinternals.com Couldn't access <host IP>: The network name cannot be found. Make sure that the default admin$ share is enabled on <host IP>. We've tried both the machine name and the IP address in with the same results. The same command has worked previously with our Win2K3 hosts - so we're presuming it is some form of security change between the 2003 and 2008R2. Anyone have any clues?

  Read the article

• Register a dll in Windows Server 2003

  - by Karee

  I'm trying to register some DLLs for a particular application but having some problems. The DLLs are stored in the application folder in the D: drive. I run cmd.exe, go to the D: drive and run regsvr32, but it gives me the error: "The was loaded, but the DllRegisterServer entry point was not found. This file cannot be registered." After searching for other solutions, I also tried copying the DLLs into the C:\WINDOWS\system32 folder and running regsvr32 directly there but that didn't work either. It gave me the same error. I'm not very familiar with Windows Administration, so I may need detailed instructions/explanations. Any help would be greatly appreciated! Thank you very much!

  Read the article

• MinGW tar compression problem

  - by Shiftbit

  I am unable to get the Mingw tar to work with compress files. It does not filter through the proper compression utility. However, tar will work if I manually uncompress the file first. I have tried in both the MSYS shell and Windows cmd. Has anyone had this problem or is it a MinGW bug? For example, this does not work: C:\Users\home\Desktop>tar -tzf wdiff-0.5.tar.gz tar: Cannot use compressed or remote archives tar: Error is not recoverable: exiting now C:\Users\home\Desktop>tar -t -Zgzip -f wdiff-0.5.tar.gz tar: Cannot use compressed or remote archives tar: Error is not recoverable: exiting now C:\Users\home\Desktop>tar -tf wdiff-0.5.tar.gz tar: Hmm, this doesn't look like a tar archive tar: Skipping to next file header tar: Only read 6732 bytes from archive wdiff-0.5.tar.gz tar: Error is not recoverable: exiting now However, this works: gzip -d wdiff-0.5.tar.gz tar -tf wdiff-0.5.tar

  Read the article

• Cannot install Windows 7 on new PC (BSOD during installation)

  - by andronz

  Yesterday I had received new hardware and tried to assemble all of it. But when I was installing Windows 7 x64 for two times I got a BSOD, and a error message like this: Your PC has rebooted unexpectly, installation will continue after reboot. I have checked everything and tried to install once more time. It was almost successful, Windows had installed, but I cannot format my disk, open cmd or control panel, boot from DVD etc. It's the first time I have assembled a PC, and I don't know where the problem is, in my hardware or in Windows. My components: MSI z77a-g43 Intel i5 3570k Seagate Barracuda (plug into sata3 slot 6 Gb, there I have also sata 3 Gb slot) Corsair XMS3 (4x4Gb) HIS IceQ Also in the BIOS, I have changed RAM frequency to DDR3 1600 and voltage to 1.65v

  Read the article

• Using VLC as RTSP server

  - by StackedCrooked

  I'm trying to figure out how to use the server capabilities of VLC. More specifically, how to export an SDP file when RTP streaming. In chapter 4 in the section related to RTP Streaming examples for server and client are given: vlc -vvv input_stream --sout '#rtp{dst=192.168.0.12,port=1234,sdp=rtsp://server.example.org:8080/test.sdp}' vlc rtsp://server.example.org:8080/test.sdp It's not very clear to me how to make it actually work. I have tried these two commands for server and client using two cmd instances: vlc -I rc screen:// --sout=#rtp{dst=127.0.0.1,port=4444,sdp=rtsp://localhost:8080/test.sdp} vlc -I rc rtsp://localhost:8080/test.sdp Invoking the second command causes the first one to crash. The second command shows the error message "could not connect to localhost:8080".

  Read the article

• OS X not booting after upgrading LibXML2

  - by Federico

  I tried upgrading the version of LibXML2 in my machine to run some propietary software. Compiled as 32-bit (-arch i386) and restarted to see if it worked. Now when I try to boot I can only get into the spinning screen and it just sits there. Restarting in verbose mode (Cmd-V) does not show any error in the process, it just freezes after "AppleIntelCPUPowerManagement: initialization complete". I can't from any CD either (if I press c on startup it just spins the disk around and then stops in the same spinner screen). I've also reset the PRAM/NVRAM to discard any problems with that and it´s still not fixed. Any pointers of what might´ve gone wrong? (Latest gen MBP, running 10.6.3)

  Read the article

• Unix : `nc` on Ubuntu vs Redhat (netcat)

  - by bguiz

  How do I achieve the equivalent of nc -q in Redhat 5? Details? nc -q -1 local host ${PORT} ${CMD} In Ubuntu, nc may be use as above, with the -q option. See manpage. -q after EOF on stdin, wait the specified number of seconds and then quit. If seconds is negative, wait forever. However, this option is not available in Redhat 5. See manpage. (Note: The Red Hat website is horrible to search, if someone finds their manpage for nc, please edit this post or comment with the new link).

  Read the article

• Software to Monitor the Stability of Internet Connection

  - by Ngu Soon Hui

  Thanks to the excellent internet connection service offered by one of the best ISP in the world, the internet connection in my area is very, very unstable. I can connect some of the time, but MOST of the time the connection will just drop off ( with the error message unable to resolve host) and after a few minutes, it will resume back. If I ping the domain name directly (i.e., ping www.google.com -t in cmd command), I will get a cannot ping message. Because of the flickery nature of the connection, it's pretty hard to prove to the support staff that internet connection is unstable. So I am thinking about using one software to record down the connection situation, so that I can present to the technical staff and make sure that they have no excuse not to fix my problem. Any such software available? Edit: Of course, such software should not record my browsing habit, and must be able to monitor and record the internet connection condition even when I am not online.

  Read the article

• Routing all Traffic through OpenVPN Tunnel

  - by Filip Ekberg

  I have installed OpenVPN server on Archlinux and am now using OpenVPN GUI on Windows 7, I can talk to other computers connected through the VPN but I have not yet figured out how to route all traffic through the tunnel. How do I do this? I figured I need to do it with route ( cmd command ) but I think i need some pointers here. I've followed the OpenVPN HowTo on the matter but that doesn't work, it simply doesn't push the "force the client to go through this gateway"-option. And changing from OpenVPN to a PPTP / IPSec alternative is not an option at the moment.

  Read the article

• Restore monitor detection to one only or restore start menu to bottom

  - by Mark

  I have a co-worker that is no longer able to see his start menu. He used to have it pinned to the left edge of his screen. I tried to troubleshoot it a bit and discovered if we do Windows + R then "cmd" [enter] the command prompt opens (but we don't see the start menu or run box), meaning the start menu is somewhere, just off screen. Restarting doesn't help. Is there some way to force Windows to think it only has a single monitor? It seems to "think" it has two but there's only one and we can get the Start menu back. Or, is there a way to restore the start menu to the bottom? Additional info We are able to right-click the desktop for display settings, etc. We can also get into Windows Explorer (via Ctrl + E) so if we need any of that to restore settings we can do it.

  Read the article

• Move Emails Easily Using Search - Outlook 2011 Feature on the MAC for Outlook 2010 Windows

  - by Arthor

  My main email client is Outlook 2010 for Windows 7. I also have a Mac but I do not use it that much however on the MAC you have Outlook 2011. In my Outlook 2010 for Windows 7, I have many many folders. There is one feature I would like to know if it is available or something similar which is on Outlook 2011 for the Mac. On the Outlook 2011 for the mac you can go to: Top Menu Message Move Choose Folder or press (SHIT+CMD "press" M) This bring up a box where you can just type the beginning part of the folder and all the folders with that beginning appears (To search), you select the one you want and the selected emails move to that folder. I hope I have explained it well. Does anyone know if there is a plugin on Outlook 2010 or may I have just missed the function. Thank you

  Read the article

• How to get my external IP address (over NAT) from the Windows command-line?

  - by Diogo Rocha

  The Windows "ipconfig" command can only show me the parameters from the Ethernet interfaces from my machine (even with the "ipconfig /all" argument). It can show detailed information about the interface, but it will never show me my external IP address over a NAT network. However, there are several websites, such as "What is my IP address" that can get and show my external IP address. So I'm wondering, is possible to get this value externally? Should I expect that there is some way to get this information from a command line at my local machine... I need to get this value to log on an application that I'm doing with VBScript. There is some way to do this, from a "cmd" on Windows?

  Read the article

• Mercurial SSH process blocks when run from Local System

  - by Liedman

  We are using Mercurial over SSH for our development. We use Hudson for continous integration, and have deployed it on Tomcat, running on a Windows 2003 Server using the Local System account. Mercurial is configured to use Putty's plink.exe as its ssh command in Mercurial.ini, together with a private key for SSH authentication. When Hudson attempts any Mercurial command over SSH, the operation just blocks. I can see the three processes being started: hg.exe, cmd.exe and plink.exe. On the remote machine, I can also see the SSH session being opened and the authentication key being accepted. After that, nothing appears to happen, and everything just blocks, seemingly forever. (As a side note, subversion/SVN over SSH works from Hudson to the same server, using the same user and authentication key). A solution would of course be the best, but at least a hint for how I should debug it to get further would be nice, since I'm stuck and haven't even got an error message right now.

  Read the article

• "dig +trace fqdn" and "dig fqdn" do not give the same result on a LAN with windows DNS server, why?

  - by Sulliwane

  in my company LAN I have a Ubuntu 14.04 server running in Virtualbox (as guest) on a Windows 7 (the host) with network interface bridged (so the Ubuntu server belongs to the LAN, with its ip: 192.168.1.85). I have a website on this server: mywebsite.com The gateway for the LAN to the internet is 192.168.1.1 (Cisco 1841)--188.188.188.254 as public IP. There is a Windows 2008 server that acts as DNS server and DHCP server on the LAN. I added a Forward zone "mywebsite.com" with A record - 192.168.1.85. Outside the LAN, mywebsite.com has public Dns records that point on the Cisco 1841 public IP (188.188.188.254) Now when I ping mywebsite.com from the lan, I quickly get 192.168.1.85. But when I'm connecting through the browser on the clients, it's not always fast. So I'm wondering: Are my requests really/directly resolved and forwarded to 192.168.1.85, OR are they sent out of the LAN, and then forwarded back to the CISCO public 188.188.188.254:80 and NAT to the Ubuntu server before being served ??? To try to answer this question, I looked for tracking the DNS request from my linux client on the LAN: v@v-ss9:~$ dig mywebsite.com ; <<>> DiG 9.9.5-3-Ubuntu <<>> mywebsite.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 24850 ;; flags: qr aa rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 0, ADDITIONAL: 1 ;; OPT PSEUDOSECTION: ; EDNS: version: 0, flags:; udp: 4000 ;; QUESTION SECTION: ;mywebsite.com. IN A ;; ANSWER SECTION: mywebsite.com. 3600 IN A 192.168.1.85 ;; Query time: 1 msec ;; SERVER: 127.0.1.1#53(127.0.1.1) ;; WHEN: Fri Aug 22 09:50:16 CST 2014 ;; MSG SIZE rcvd: 66 This answer looks right: 192.168.1.85. But then look at this: v@v-ss9:~$ dig +trace mywebsite.com ; <<>> DiG 9.9.5-3-Ubuntu <<>> +trace mywebsite.com ;; global options: +cmd . 12955 IN NS h.gtld-servers.net. . 12955 IN NS g.gtld-servers.net. . 12955 IN NS m.gtld-servers.net. . 12955 IN NS i.gtld-servers.net. . 12955 IN NS l.gtld-servers.net. . 12955 IN NS k.gtld-servers.net. . 12955 IN NS j.gtld-servers.net. . 12955 IN NS d.gtld-servers.net. . 12955 IN NS b.gtld-servers.net. . 12955 IN NS c.gtld-servers.net. . 12955 IN NS a.gtld-servers.net. . 12955 IN NS e.gtld-servers.net. . 12955 IN NS f.gtld-servers.net. ;; Received 516 bytes from 127.0.1.1#53(127.0.1.1) in 18 ms mywebsite.com. 172800 IN NS ns3.rmi.fr. mywebsite.com. 172800 IN NS ns4.rmi.fr. CK0POJMG874LJREF7EFN8430QVIT8BSM.com. 86400 IN NSEC3 1 1 0 - CK0QFMDQRCSRU0651QLVA1JQB21IF7UR NS SOA RRSIG DNSKEY NSEC3PARAM CK0POJMG874LJREF7EFN8430QVIT8BSM.com. 86400 IN RRSIG NSEC3 8 2 86400 20140825045016 20140818034016 6122 com. Imq8K9xlvFXlB4IjUkdxOc5YHoTEhqSQUlRSJ9QCIhd9wzGpWJ54AfVf WJ0SUKThalpzqS0cXdLGtNmuYgqLfwUMjpUlT4c+zJyx7I4QMPLImQZh Ov0xy3mUr7dLlymAJYGs9dLI2IaheLvpKTBwaV1gAvo8QEkU8VRiJ7gW 9dk= U0PIA23FHMVPTKSDHC9PJ1BEA9SIB65R.com. 86400 IN NSEC3 1 1 0 - U0PL33R61V6TCCPBS1171PROP57ASRD9 NS DS RRSIG U0PIA23FHMVPTKSDHC9PJ1BEA9SIB65R.com. 86400 IN RRSIG NSEC3 8 2 86400 20140825043502 20140818032502 6122 com. qsC5sJbwklao+OedCHpcYo56aQaY0N+7peKmPu8szvjAQoJFRWyuDfAh Nw/gvHXEMzG7tYLriQGVfsiK8GZdPXyG4Ghe1MNN4jOZnSahkT5LjlqL 5QyGC0QiClRMPDAYjUOFGQDkjOJcJYvTNkEyXC2BEpfLI5SwCbYqwqg3 RkE= ;; Received 585 bytes from 192.41.162.30#53(l.gtld-servers.net) in 297 ms mywebsite.com. 86400 IN A 188.188.188.254 mywebsite.com. 86400 IN NS ns3.rmi.fr. mywebsite.com. 86400 IN NS ns4.rmi.fr. ;; Received 204 bytes from 212.51.161.18#53(ns3.rmi.fr) in 310 ms Here I get my CISCO public IP 188.188.188.254!!! Is it normal? How to know if my browser (from the LAN) is really directly communicating with 192.168.1.85 when using mywebsite.com? Thank you for your help.

  Read the article

• How to get my external IP address(over NAT) from Windows command-line?

  - by Diogo Rocha

  Windows "ipconfig" command can only show me the parameters from the ethernet interfaces from my machine(even with the "ipconfig /all" argument), it can show detailed information about the interface, but will never show me my external IP address over a NAT network. However, there are several websites, such as "What is my IP" that can get and show my external IP addres. So I'm wondering, if is possible to get this value externally, should I expect that there is some way to get this information from a command line at my local machine... I need to get this value to log on an application that I'm doing with VB Script. There is some way to do this, from a "cmd" on Windows?

  Read the article

• Restore monitor detection to one only or restore start menu to bottom [Windows 7]

  - by Mark

  I have a co-worker that is no longer able to see his start menu. He used to have it pinned to the left edge of his screen. I tried to troubleshoot it a bit and discovered if we do Windows + R then "cmd" [enter] the command prompt opens (but we don't see the start menu or run box), meaning the start menu is somewhere, just off screen. Restarting doesn't help. Is there some way to force Windows to think it only has a single monitor? It seems to "think" it has two but there's only one and we can get the Start menu back. Or, is there a way to restore the start menu to the bottom? Additional info We are able to right-click the desktop for display settings, etc. We can also get into Windows Explorer (via Ctrl + E) so if we need any of that to restore settings we can do it.

  Read the article

• How do I setup an FTP server on Windows 7?

  - by Matt Frear

  I'm having trouble getting an FTP server setup on Windows 7. I've added the service using Control Panel - Programs - Turn Windows features on and off. I can see the service has started in Control Panel - Services. But then when I fire up a Windows command-line window, cmd, I get Not connected., C:\Users\mattf>ftp localhost ftp> ls Not connected. ftp> open localhost ftp> ls Not connected. ftp> dir Not connected. ftp> quit C:\Users\mattf> And that's as far as I've got. I have no idea why this isn't working - could it be firewall settings?

  Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >