Search Results

Search found 2372 results on 95 pages for 'flashing the bios'.

Page 59/95 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

• Replacement Alternative for Dell FY606 in a Poweredge T105

  - by Mike C

  I have recently upgraded my Poweredge T105 server to use a SAS 6/ir RAID controller. Unfortunately, I did not realize at the time that adding the card would cause the BIOS to complain about a missing hard drive fan. This warning requires that a user press F1 to continue, which is disastrous in a server environment. I have searched all over found that the specific part I need is a Dell FY606 fan. However, I have yet to find a suitable retailer that covers this part. I have contacted Dell and they do not have this part in stock. Are there any alternative models of a fan that I could use in place of an FY606? Seems like a pretty straightforward part, just a fan that connects to a 4-pin power connector on the motherboard.

  Read the article

• How do I get Windows 7 To Recognize a newly installed RAID 5 volume?

  - by GregH

  I had a previously running Windows 7 (64 bit) system. I added 3 new 1TB Seagate drives that I set up as a RAID 5 volume. I have a Gigabyte GA-P55M-UD2 motherboard. I installed the drives, set up the BIOS and configured the three drives as a RAID volume through the RAID setup utility that was accessed via Ctrl-I while the system was booting. I rebooted the system and could see the drives during the boot sequence. However, when Windows 7 was starting I got an error (quick blue screen) and then Windows tried to repair itself with no success. Do I need to install RAID drivers in Windows? How do I do it if Windows won't boot? Thanks in advance.

  Read the article

• Linux driver for Intel ICH10R

  - by Pablo Santa Cruz

  Hi! I would like to know what 64-bit Linux distribution can I use with an Intel ICH10R RAID. I have tried CentOS 5.2 and Ubuntu Server 8.04. Neither support that raid controller. Also, I would like to know where do I setup the RAID-5 I want to use. I am using a TYAN S7002 motherboard and the BIOS software does not include an option to configure the RAID as I am used to do with Dell servers... Thanks a lot in advance.

  Read the article

• Having issues with flickering output to TV from Windows 7 laptop

  - by Nimmy Lebby

  I cannot tell why this is happening. I cannot get a pattern as to when it happens. Sometimes, I watch entire Hulu content without any interruptions. Other times, it happens 2-3 times in a span of 3 minutes. Then it stops for 10-15 minutes. Lenovo T410s Integrated graphics: Intel HD Graphics (Driver=8.15.10.2253, Video BIOS=2026.1) TV is a Zenith (does not happen with other laptop so doubt it's TV) TV connected to laptop using HDMI-to-DVI cable (previously was connected directly via DVI but I bought a new cable and it's still happening) Anyone could help me troubleshoot this? I'd greatly appreciate it. If you need more information, I'll be glad to provide it.

  Read the article

• Garbled text in Screen [closed]

  - by Prabin Dahal

  The graphical Interface in my system is garbled with some text. At the beginning I thought it was due to java and tomcat that I installed. But after removing java and tomcat, it is still the same. I am using ubuntu server and i have installed xfce desktop environment with oboard softkey I have added my dmesg output to this message. What is the problem here. I am not able to figure it out. Thank you for your help. Prabin [ 0.390936] usbcore: registered new interface driver usbfs [ 0.391006] usbcore: registered new interface driver hub [ 0.391147] usbcore: registered new device driver usb [ 0.391580] PCI: Using ACPI for IRQ routing [ 0.400509] PCI: pci_cache_line_size set to 64 bytes [ 0.400669] reserve RAM buffer: 000000000009ec00 - 000000000009ffff [ 0.400681] reserve RAM buffer: 000000007f597000 - 000000007fffffff [ 0.400699] reserve RAM buffer: 000000007f6f0000 - 000000007fffffff [ 0.401135] NetLabel: Initializing [ 0.401155] NetLabel: domain hash size = 128 [ 0.401168] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.401212] NetLabel: unlabeled traffic allowed by default [ 0.401466] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.401494] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.401520] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 0.408228] Switching to clocksource hpet [ 0.434341] AppArmor: AppArmor Filesystem Enabled [ 0.434447] pnp: PnP ACPI init [ 0.434531] ACPI: bus type pnp registered [ 0.434784] pnp 00:00: [bus 00-ff] [ 0.434794] pnp 00:00: [io 0x0cf8-0x0cff] [ 0.434804] pnp 00:00: [io 0x0000-0x0cf7 window] [ 0.434813] pnp 00:00: [io 0x0d00-0xffff window] [ 0.434822] pnp 00:00: [mem 0x000a0000-0x000bffff window] [ 0.434831] pnp 00:00: [mem 0x00000000 window] [ 0.434840] pnp 00:00: [mem 0x80000000-0xffffffff window] [ 0.435018] pnp 00:00: Plug and Play ACPI device, IDs PNP0a08 PNP0a03 (active) [ 0.435526] pnp 00:01: [mem 0xe0000000-0xefffffff] [ 0.435537] pnp 00:01: [mem 0x7f700000-0x7f7fffff] [ 0.435545] pnp 00:01: [mem 0x7f800000-0x7fffffff] [ 0.435554] pnp 00:01: [mem 0xfee00000-0xfeefffff] [ 0.435727] system 00:01: [mem 0xe0000000-0xefffffff] has been reserved [ 0.435754] system 00:01: [mem 0x7f700000-0x7f7fffff] has been reserved [ 0.435775] system 00:01: [mem 0x7f800000-0x7fffffff] has been reserved [ 0.435796] system 00:01: [mem 0xfee00000-0xfeefffff] has been reserved [ 0.435818] system 00:01: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.436233] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436245] pnp 00:02: [io 0x0000-0xffffffffffffffff disabled] [ 0.436414] system 00:02: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.436512] pnp 00:03: [io 0x0060] [ 0.436521] pnp 00:03: [io 0x0064] [ 0.436548] pnp 00:03: [irq 1] [ 0.436682] pnp 00:03: Plug and Play ACPI device, IDs PNP0303 PNP030b (active) [ 0.436825] pnp 00:04: [irq 12] [ 0.436958] pnp 00:04: Plug and Play ACPI device, IDs PNP0f03 PNP0f13 (active) [ 0.437835] pnp 00:05: [io 0x03f8-0x03ff] [ 0.437861] pnp 00:05: [irq 4] [ 0.437870] pnp 00:05: [dma 0 disabled] [ 0.438142] pnp 00:05: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439014] pnp 00:06: [io 0x02f8-0x02ff] [ 0.439036] pnp 00:06: [irq 3] [ 0.439045] pnp 00:06: [dma 0 disabled] [ 0.439297] pnp 00:06: Plug and Play ACPI device, IDs PNP0501 (active) [ 0.439346] pnp 00:07: [io 0x0000-0x000f] [ 0.439355] pnp 00:07: [io 0x0081-0x0083] [ 0.439363] pnp 00:07: [io 0x0087] [ 0.439371] pnp 00:07: [io 0x0089-0x008b] [ 0.439380] pnp 00:07: [io 0x008f] [ 0.439388] pnp 00:07: [io 0x00c0-0x00df] [ 0.439563] system 00:07: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.439617] pnp 00:08: [io 0x0070-0x0077] [ 0.439639] pnp 00:08: [irq 8] [ 0.439751] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active) [ 0.439788] pnp 00:09: [io 0x0061] [ 0.439893] pnp 00:09: Plug and Play ACPI device, IDs PNP0800 (active) [ 0.439977] pnp 00:0a: [io 0x0010-0x001f] [ 0.439986] pnp 00:0a: [io 0x0022-0x003f] [ 0.439994] pnp 00:0a: [io 0x0044-0x005f] [ 0.440055] pnp 00:0a: [io 0x0063] [ 0.440063] pnp 00:0a: [io 0x0065] [ 0.440071] pnp 00:0a: [io 0x0067-0x006f] [ 0.440079] pnp 00:0a: [io 0x0072-0x007f] [ 0.440086] pnp 00:0a: [io 0x0080] [ 0.440094] pnp 00:0a: [io 0x0084-0x0086] [ 0.440102] pnp 00:0a: [io 0x0088] [ 0.440109] pnp 00:0a: [io 0x008c-0x008e] [ 0.440117] pnp 00:0a: [io 0x0090-0x009f] [ 0.440125] pnp 00:0a: [io 0x00a2-0x00bf] [ 0.440133] pnp 00:0a: [io 0x00e0-0x00ef] [ 0.440141] pnp 00:0a: [io 0x04d0-0x04d1] [ 0.440150] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440160] pnp 00:0a: [io 0x0000-0xffffffffffffffff disabled] [ 0.440168] pnp 00:0a: [io 0x03f4] [ 0.440175] pnp 00:0a: [io 0x03f5] [ 0.440183] pnp 00:0a: [io 0x0374] [ 0.440190] pnp 00:0a: [io 0x0375] [ 0.440405] system 00:0a: [io 0x04d0-0x04d1] has been reserved [ 0.440432] system 00:0a: [io 0x03f4] has been reserved [ 0.440451] system 00:0a: [io 0x03f5] has been reserved [ 0.440469] system 00:0a: [io 0x0374] has been reserved [ 0.440488] system 00:0a: [io 0x0375] has been reserved [ 0.440508] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.440550] pnp 00:0b: [io 0x00f0-0x00ff] [ 0.440572] pnp 00:0b: [irq 13] [ 0.440691] pnp 00:0b: Plug and Play ACPI device, IDs PNP0c04 (active) [ 0.440770] pnp 00:0c: [io 0x0810] [ 0.440779] pnp 00:0c: [io 0x0800-0x080f] [ 0.440787] pnp 00:0c: [io 0xffff] [ 0.440947] system 00:0c: [io 0x0810] has been reserved [ 0.440970] system 00:0c: [io 0x0800-0x080f] has been reserved [ 0.440989] system 00:0c: [io 0xffff] has been reserved [ 0.441010] system 00:0c: Plug and Play ACPI device, IDs PNP0c02 (active) [ 0.441620] pnp 00:0d: [io 0x0900-0x097f] [ 0.441630] pnp 00:0d: [io 0x09c0-0x09ff] [ 0.441639] pnp 00:0d: [io 0x0400-0x043f] [ 0.441647] pnp 00:0d: [io 0x0480-0x04bf] [ 0.441656] pnp 00:0d: [mem 0xfec00000-0xfec85fff] [ 0.441664] pnp 00:0d: [mem 0xfed1c000-0xfed1ffff] [ 0.441673] pnp 00:0d: [mem 0x000c0000-0x000dffff] [ 0.441689] pnp 00:0d: [mem 0x000e0000-0x000effff] [ 0.441697] pnp 00:0d: [mem 0x000f0000-0x000fffff] [ 0.441706] pnp 00:0d: [mem 0xff800000-0xffffffff] [ 0.441911] system 00:0d: [io 0x0900-0x097f] has been reserved [ 0.441935] system 00:0d: [io 0x09c0-0x09ff] has been reserved [ 0.441955] system 00:0d: [io 0x0400-0x043f] has been reserved [ 0.441975] system 00:0d: [io 0x0480-0x04bf] has been reserved [ 0.441997] system 00:0d: [mem 0xfec00000-0xfec85fff] could not be reserved [ 0.442019] system 00:0d: [mem 0xfed1c000-0xfed1ffff] has been reserved [ 0.442040] system 00:0d: [mem 0x000c0000-0x000dffff] could not be reserved [ 0.442061] system 00:0d: [mem 0x000e0000-0x000effff] could not be reserved [ 0.442082] system 00:0d: [mem 0x000f0000-0x000fffff] could not be reserved [ 0.442103] system 00:0d: [mem 0xff800000-0xffffffff] has been reserved [ 0.442126] system 00:0d: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.442308] pnp 00:0e: [mem 0xfed00000-0xfed003ff] [ 0.442454] pnp 00:0e: Plug and Play ACPI device, IDs PNP0103 (active) [ 0.442569] pnp 00:0f: [mem 0x7f6f0000-0x7f6fffff] [ 0.442762] system 00:0f: [mem 0x7f6f0000-0x7f6fffff] has been reserved [ 0.442788] system 00:0f: Plug and Play ACPI device, IDs PNP0c01 (active) [ 0.443360] pnp: PnP ACPI: found 16 devices [ 0.443378] ACPI: ACPI bus type pnp unregistered [ 0.443395] PnPBIOS: Disabled by ACPI PNP [ 0.486106] PCI: max bus depth: 3 pci_try_num: 4 [ 0.486189] pci 0000:00:1c.0: PCI bridge to [bus 01-01] [ 0.486217] pci 0000:00:1c.0: bridge window [io 0xe000-0xefff] [ 0.486241] pci 0000:00:1c.0: bridge window [mem 0xd0100000-0xd01fffff] [ 0.486266] pci 0000:00:1c.0: bridge window [mem 0xff700000-0xff7fffff pref] [ 0.486298] pci 0000:03:01.0: PCI bridge to [bus 04-04] [ 0.486319] pci 0000:03:01.0: bridge window [io 0xd000-0xdfff] [ 0.486348] pci 0000:03:01.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486374] pci 0000:03:01.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486406] pci 0000:03:02.0: PCI bridge to [bus 05-05] [ 0.486444] pci 0000:03:03.0: PCI bridge to [bus 06-06] [ 0.486479] pci 0000:02:00.0: PCI bridge to [bus 03-06] [ 0.486499] pci 0000:02:00.0: bridge window [io 0xd000-0xdfff] [ 0.486522] pci 0000:02:00.0: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486545] pci 0000:02:00.0: bridge window [mem 0xff600000-0xff6fffff 64bit pref] [ 0.486575] pci 0000:00:1c.1: PCI bridge to [bus 02-06] [ 0.486593] pci 0000:00:1c.1: bridge window [io 0xd000-0xdfff] [ 0.486615] pci 0000:00:1c.1: bridge window [mem 0xd0000000-0xd00fffff] [ 0.486637] pci 0000:00:1c.1: bridge window [mem 0xff600000-0xff6fffff pref] [ 0.486710] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.486735] pci 0000:00:1c.0: setting latency timer to 64 [ 0.486774] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.486796] pci 0000:00:1c.1: setting latency timer to 64 [ 0.486817] pci 0000:02:00.0: setting latency timer to 64 [ 0.486836] pci 0000:03:01.0: setting latency timer to 64 [ 0.486858] pci 0000:03:02.0: setting latency timer to 64 [ 0.486880] pci 0000:03:03.0: setting latency timer to 64 [ 0.486893] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7] [ 0.486902] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff] [ 0.486912] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff] [ 0.486922] pci_bus 0000:00: resource 7 [mem 0x80000000-0xffffffff] [ 0.486932] pci_bus 0000:01: resource 0 [io 0xe000-0xefff] [ 0.486941] pci_bus 0000:01: resource 1 [mem 0xd0100000-0xd01fffff] [ 0.486951] pci_bus 0000:01: resource 2 [mem 0xff700000-0xff7fffff pref] [ 0.486961] pci_bus 0000:02: resource 0 [io 0xd000-0xdfff] [ 0.486970] pci_bus 0000:02: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.486980] pci_bus 0000:02: resource 2 [mem 0xff600000-0xff6fffff pref] [ 0.486989] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff] [ 0.486998] pci_bus 0000:03: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487008] pci_bus 0000:03: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487018] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff] [ 0.487028] pci_bus 0000:04: resource 1 [mem 0xd0000000-0xd00fffff] [ 0.487038] pci_bus 0000:04: resource 2 [mem 0xff600000-0xff6fffff 64bit pref] [ 0.487177] NET: Registered protocol family 2 [ 0.487405] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.488397] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.489792] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.490493] TCP: Hash tables configured (established 131072 bind 65536) [ 0.490525] TCP reno registered [ 0.490551] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.490590] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.490898] NET: Registered protocol family 1 [ 0.490970] pci 0000:00:02.0: Boot video device [ 0.491052] pci 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 0.491092] pci 0000:00:1d.0: PCI INT A disabled [ 0.491134] pci 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 0.491174] pci 0000:00:1d.1: PCI INT B disabled [ 0.491220] pci 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 0.491259] pci 0000:00:1d.2: PCI INT C disabled [ 0.491307] pci 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 0.864431] Freeing initrd memory: 13820k freed [ 2.088042] pci 0000:00:1d.7: EHCI: BIOS handoff failed (BIOS bug?) 01010001 [ 2.088207] pci 0000:00:1d.7: PCI INT D disabled [ 2.088267] PCI: CLS 64 bytes, default 64 [ 2.089248] audit: initializing netlink socket (disabled) [ 2.089287] type=2000 audit(1349363630.084:1): initialized [ 2.144783] highmem bounce pool size: 64 pages [ 2.144808] HugeTLB registered 2 MB page size, pre-allocated 0 pages [ 2.160057] VFS: Disk quotas dquot_6.5.2 [ 2.160232] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.161716] fuse init (API version 7.17) [ 2.161995] msgmni has been set to 1713 [ 2.162925] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 2.163008] io scheduler noop registered [ 2.163023] io scheduler deadline registered [ 2.163048] io scheduler cfq registered (default) [ 2.163339] pcieport 0000:00:1c.0: setting latency timer to 64 [ 2.163530] pcieport 0000:00:1c.1: setting latency timer to 64 [ 2.163706] pcieport 0000:02:00.0: setting latency timer to 64 [ 2.163873] pcieport 0000:03:01.0: setting latency timer to 64 [ 2.163964] pcieport 0000:03:01.0: irq 40 for MSI/MSI-X [ 2.164193] pcieport 0000:03:02.0: setting latency timer to 64 [ 2.164272] pcieport 0000:03:02.0: irq 41 for MSI/MSI-X [ 2.164453] pcieport 0000:03:03.0: setting latency timer to 64 [ 2.164531] pcieport 0000:03:03.0: irq 42 for MSI/MSI-X [ 2.164783] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt [ 2.164801] pci 0000:01:00.0: Signaling PME through PCIe PME interrupt [ 2.164816] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded [ 2.164853] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt [ 2.164867] pcieport 0000:02:00.0: Signaling PME through PCIe PME interrupt [ 2.164880] pcieport 0000:03:01.0: Signaling PME through PCIe PME interrupt [ 2.164892] pci 0000:04:00.0: Signaling PME through PCIe PME interrupt [ 2.164904] pcieport 0000:03:02.0: Signaling PME through PCIe PME interrupt [ 2.164917] pcieport 0000:03:03.0: Signaling PME through PCIe PME interrupt [ 2.164932] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded [ 2.164988] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 2.165115] pciehp 0000:00:1c.0:pcie04: HPC vendor_id 8086 device_id 8110 ss_vid 8086 ss_did 8119 [ 2.165177] pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded [ 2.165199] pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 device_id 8112 ss_vid 8086 ss_did 8119 [ 2.165260] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded [ 2.165290] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 2.165488] intel_idle: MWAIT substates: 0x3020220 [ 2.165508] intel_idle: v0.4 model 0x1C [ 2.165513] intel_idle: lapic_timer_reliable_states 0x2 [ 2.165519] Marking TSC unstable due to TSC halts in idle states deeper than C2 [ 2.165779] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input0 [ 2.165855] ACPI: Lid Switch [LID] [ 2.165983] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1 [ 2.166005] ACPI: Power Button [PWRB] [ 2.173811] thermal LNXTHERM:00: registered as thermal_zone0 [ 2.173829] ACPI: Thermal Zone [TZ00] (48 C) [ 2.174004] thermal LNXTHERM:01: registered as thermal_zone1 [ 2.174018] ACPI: Thermal Zone [TZ01] (34 C) [ 2.174194] thermal LNXTHERM:02: registered as thermal_zone2 [ 2.174207] ACPI: Thermal Zone [TZ02] (34 C) [ 2.174378] thermal LNXTHERM:03: registered as thermal_zone3 [ 2.174392] ACPI: Thermal Zone [TZ03] (34 C) [ 2.174503] ERST: Table is not found! [ 2.174513] GHES: HEST is not enabled! [ 2.174601] isapnp: Scanning for PnP cards... [ 2.176175] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled [ 2.196702] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.292409] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.528909] isapnp: No Plug & Play device found [ 2.588733] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 2.624523] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 2.640702] Linux agpgart interface v0.103 [ 2.645138] brd: module loaded [ 2.647452] loop: module loaded [ 2.648149] pata_acpi 0000:00:1f.1: setting latency timer to 64 [ 2.649238] Fixed MDIO Bus: probed [ 2.649315] tun: Universal TUN/TAP device driver, 1.6 [ 2.649327] tun: (C) 1999-2004 Max Krasnyansky <[email protected]> [ 2.649524] PPP generic driver version 2.4.2 [ 2.649824] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.649884] ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23 [ 2.649937] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 2.649946] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 2.650082] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 [ 2.650148] ehci_hcd 0000:00:1d.7: debug port 1 [ 2.654045] ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported [ 2.654093] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xd02c4000 [ 2.668035] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 2.668392] hub 1-0:1.0: USB hub found [ 2.668413] hub 1-0:1.0: 8 ports detected [ 2.668618] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.668666] uhci_hcd: USB Universal Host Controller Interface driver [ 2.668726] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 [ 2.668751] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 2.668759] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 2.668910] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 [ 2.668981] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000f040 [ 2.669335] hub 2-0:1.0: USB hub found [ 2.669355] hub 2-0:1.0: 2 ports detected [ 2.669508] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 2.669531] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 2.669538] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 2.669675] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 [ 2.669739] uhci_hcd 0000:00:1d.1: irq 21, io base 0x0000f020 [ 2.670099] hub 3-0:1.0: USB hub found [ 2.670118] hub 3-0:1.0: 2 ports detected [ 2.670271] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22 [ 2.670295] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 2.670302] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 2.670435] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 [ 2.670502] uhci_hcd 0000:00:1d.2: irq 22, io base 0x0000f000 [ 2.670869] hub 4-0:1.0: USB hub found [ 2.670888] hub 4-0:1.0: 2 ports detected [ 2.671186] usbcore: registered new interface driver libusual [ 2.671332] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 2.673408] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.673437] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.673844] mousedev: PS/2 mouse device common for all mice [ 2.674272] rtc_cmos 00:08: RTC can wake from S4 [ 2.674482] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0 [ 2.674529] rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs [ 2.674691] device-mapper: uevent: version 1.0.3 [ 2.674903] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: [email protected] [ 2.675024] EISA: Probing bus 0 at eisa.0 [ 2.675037] EISA: Cannot allocate resource for mainboard [ 2.675050] Cannot allocate resource for EISA slot 1 [ 2.675061] Cannot allocate resource for EISA slot 2 [ 2.675072] Cannot allocate resource for EISA slot 3 [ 2.675083] Cannot allocate resource for EISA slot 4 [ 2.675094] Cannot allocate resource for EISA slot 5 [ 2.675105] Cannot allocate resource for EISA slot 6 [ 2.675116] Cannot allocate resource for EISA slot 7 [ 2.675127] Cannot allocate resource for EISA slot 8 [ 2.675137] EISA: Detected 0 cards. [ 2.675161] cpufreq-nforce2: No nForce2 chipset. [ 2.675401] cpuidle: using governor ladder [ 2.675786] cpuidle: using governor menu [ 2.675797] EFI Variables Facility v0.08 2004-May-17 [ 2.676429] TCP cubic registered [ 2.676751] NET: Registered protocol family 10 [ 2.678031] NET: Registered protocol family 17 [ 2.678052] Registering the dns_resolver key type [ 2.678107] Using IPI No-Shortcut mode [ 2.678515] PM: Hibernation image not present or could not be loaded. [ 2.678543] registered taskstats version 1 [ 2.701145] Magic number: 0:84:234 [ 2.701312] rtc_cmos 00:08: setting system clock to 2012-10-04 15:13:51 UTC (1349363631) [ 2.702280] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found [ 2.702294] EDD information not available. [ 2.702858] Freeing unused kernel memory: 740k freed [ 2.703630] Write protecting the kernel text: 5816k [ 2.703692] Write protecting the kernel read-only data: 2376k [ 2.703706] NX-protecting the kernel data: 4424k [ 2.751226] udevd[84]: starting version 175 [ 2.980162] usb 1-1: new high-speed USB device number 2 using ehci_hcd [ 3.001394] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.001474] r8169 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.001554] r8169 0000:01:00.0: setting latency timer to 64 [ 3.001654] r8169 0000:01:00.0: irq 43 for MSI/MSI-X [ 3.004220] r8169 0000:01:00.0: eth0: RTL8168c/8111c at 0xf8416000, 00:18:92:03:10:46, XID 1c4000c0 IRQ 43 [ 3.004254] r8169 0000:01:00.0: eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.004347] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 3.005085] r8169 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 3.005182] r8169 0000:04:00.0: setting latency timer to 64 [ 3.005292] r8169 0000:04:00.0: irq 44 for MSI/MSI-X [ 3.007187] r8169 0000:04:00.0: eth1: RTL8168c/8111c at 0xf8418000, 00:18:92:03:10:47, XID 1c4000c0 IRQ 44 [ 3.007224] r8169 0000:04:00.0: eth1: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 3.034417] pata_sch 0000:00:1f.1: version 0.2 [ 3.034518] pata_sch 0000:00:1f.1: setting latency timer to 64 [ 3.036698] scsi0 : pata_sch [ 3.039842] scsi1 : pata_sch [ 3.040913] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf060 irq 14 [ 3.040940] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf068 irq 15 [ 3.131850] Initializing USB Mass Storage driver... [ 3.136405] scsi2 : usb-storage 1-1:1.0 [ 3.136642] usbcore: registered new interface driver usb-storage [ 3.136656] USB Mass Storage support registered. [ 3.524465] usb 3-1: new low-speed USB device number 2 using uhci_hcd [ 3.968144] usb 3-2: new full-speed USB device number 3 using uhci_hcd [ 4.137903] scsi 2:0:0:0: Direct-Access TS TS4GUFM-H 1100 PQ: 0 ANSI: 0 CCS [ 4.140067] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 4.140590] sd 2:0:0:0: [sda] 8028160 512-byte logical blocks: (4.11 GB/3.82 GiB) [ 4.141597] sd 2:0:0:0: [sda] Write Protect is off [ 4.141618] sd 2:0:0:0: [sda] Mode Sense: 43 00 00 00 [ 4.142974] sd 2:0:0:0: [sda] No Caching mode page present [ 4.143000] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.145837] sd 2:0:0:0: [sda] No Caching mode page present [ 4.145858] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.147931] sda: sda1 sda2 < sda5 > [ 4.150972] sd 2:0:0:0: [sda] No Caching mode page present [ 4.151001] sd 2:0:0:0: [sda] Assuming drive cache: write through [ 4.151023] sd 2:0:0:0: [sda] Attached SCSI disk [ 4.249168] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input2 [ 4.249579] generic-usb 0003:046A:004B.0001: input,hidraw0: USB HID v1.11 Keyboard [HID 046a:004b] on usb-0000:00:1d.1-1/input0 [ 4.287805] input: HID 046a:004b as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.1/input/input3 [ 4.289235] generic-usb 0003:046A:004B.0002: input,hidraw1: USB HID v1.11 Mouse [HID 046a:004b] on usb-0000:00:1d.1-1/input1 [ 4.297604] input: EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input4 [ 4.298913] generic-usb 0003:04E7:0050.0003: input,hidraw2: USB HID v1.00 Pointer [EloTouchSystems,Inc Elo TouchSystems 2216 AccuTouch\xffffffc2\xffffffae\xffffffae USB Touchmonitor Interface] on usb-0000:00:1d.1-2/input0 [ 4.299878] usbcore: registered new interface driver usbhid [ 4.299925] usbhid: USB HID core driver [ 4.352639] EXT4-fs (sda1): INFO: recovery required on readonly filesystem [ 4.352661] EXT4-fs (sda1): write access will be enabled during recovery [ 8.519257] EXT4-fs (sda1): recovery complete [ 8.564389] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null) [ 14.280922] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 14.280944] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 14.310368] udevd[308]: starting version 175 [ 14.353873] Adding 1045500k swap on /dev/sda5. Priority:-1 extents:1 across:1045500k [ 14.428718] lp: driver loaded but no devices found [ 14.521667] EXT4-fs (sda1): re-mounted. Opts: errors=remount-ro [ 15.073459] [drm] Initialized drm 1.1.0 20060810 [ 15.097073] psb_gfx: module is from the staging directory, the quality is unknown, you have been warned. [ 15.180630] gma500 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 15.180648] gma500 0000:00:02.0: setting latency timer to 64 [ 15.182117] Stolen memory information [ 15.182127] base in RAM: 0x7f800000 [ 15.182134] size: 7932K, calculated by (GTT RAM base) - (Stolen base), seems wrong [ 15.182143] the correct size should be: 8M(dvmt mode=3) [ 15.234889] Set up 1983 stolen pages starting at 0x7f800000, GTT offset 0K [ 15.235126] [drm] SGX core id = 0x01130000 [ 15.235135] [drm] SGX core rev major = 0x01, minor = 0x02 [ 15.235143] [drm] SGX core rev maintenance = 0x01, designer = 0x00 [ 15.268796] [Firmware Bug]: ACPI: No _BQC method, cannot determine initial brightness [ 15.269888] acpi device:04: registered as cooling_device2 [ 15.270568] acpi device:05: registered as cooling_device3 [ 15.270947] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input5 [ 15.271238] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) [ 15.271424] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [ 15.271434] [drm] No driver support for vblank timestamp query. [ 15.374694] type=1400 audit(1349363644.167:2): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=435 comm="apparmor_parser" [ 15.385518] type=1400 audit(1349363644.179:3): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=435 comm="apparmor_parser" [ 15.386369] type=1400 audit(1349363644.179:4): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=435 comm="apparmor_parser" [ 15.677514] r8169 0000:01:00.0: eth0: link down [ 15.694828] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.537490] gma500 0000:00:02.0: allocated 800x480 fb [ 16.558066] fbcon: psbfb (fb0) is primary device [ 16.747122] gma500 0000:00:02.0: BL bug: Reg 00000000 save 00000000 [ 16.775550] Console: switching to colour frame buffer device 100x30 [ 16.781804] fb0: psbfb frame buffer device [ 16.781812] drm: registered panic notifier [ 16.870168] [drm] Initialized gma500 1.0.0 2011-06-06 for 0000:00:02.0 on minor 0 [ 16.871166] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871186] snd_hda_intel 0000:00:1b.0: power state changed by ACPI to D0 [ 16.871207] snd_hda_intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 16.871284] snd_hda_intel 0000:00:1b.0: setting latency timer to 64 [ 29.338953] r8169 0000:01:00.0: eth0: link up [ 29.339471] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 31.427223] init: failsafe main process (675) killed by TERM signal [ 31.522411] type=1400 audit(1349363660.316:5): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=889 comm="apparmor_parser" [ 31.523956] type=1400 audit(1349363660.316:6): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=889 comm="apparmor_parser" [ 31.524882] type=1400 audit(1349363660.320:7): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=889 comm="apparmor_parser" [ 31.525940] type=1400 audit(1349363660.320:8): apparmor="STATUS" operation="profile_load" name="/usr/sbin/tcpdump" pid=891 comm="apparmor_parser" [ 34.526445] postgres (1003): /proc/1003/oom_adj is deprecated, please use /proc/1003/oom_score_adj instead. [ 40.144048] eth0: no IPv6 routers present

  Read the article

• How to keep the function key locked on Lenovo E431?

  - by Bob

  For the Lenovo e431, how do you keep the function key locked. Right now, the default is when you press F1-F12, he multimedia controls are active. To get to the standard F1-F12, you have to hold down Fn+the function key. This used to available in bios, but for this laptop model, it no longer is available. You can press Fn+esc, and it locks it for that session, but when the computer reboots, this is reset back to the default. Is there a way so that the default is not the multimedia function keys, but just the standard, legacy function keys? Thanks.

  Read the article

• Stuck on Checking battery state at startup in Ubuntu, have splash screen no startup

  - by jeffhsu3

  I am running Ubuntu 10.04 LTS. When I boot up the computer it goes to the splash but there is no login screen, just the purple background and the mouse cursor. "Checking battery state" is the last line that does not have an "[OK]". When I press Ctr-alt-shift-F1 I can login and sudo stop gdm and startx. However this makes it so that the applets don't show. Error: "The panel encountered a problem while loading "OAFIID:GNOME_notificationAreaApplet" and does it for every single applet. Everything else works fine though. I get a EHCI: BIOS handoff failed twice in the dmesg as well. The laptop has intel mobile integrated graphics. UPDATE: Now my desktop has the exact same problem. Things that I have tried: Changing to GRUB_CMDLINE_LINUX_DEFAULT="i915.modeset=1 acpi=off"

  Read the article

• Very poor battery life on Lenovo ThinkPad W500 laptop

  - by Matt

  I have a new ThinkPad W500 laptop (w/ 9 cell battery) running Windows 7 RTM 64-bit. All drivers* and BIOS are the latest. Battery life appeared poor so I performed several tests under the following conditions: Battery starts with 100% charge Screen on minimum brightness Screen saver running Wifi n enabled and active "Normal" set of programs running including Outlook 2007, FeedDemon, TweetDeck and antivirus Laptop left untouched during tests Under the above conditions, I clocked under 2 hours of battery life across 3 tests (1:49, 1:52, 1:47). If I actually use the computer, we're looking at 1:30. Something is not right... The smoking gun here is that Lenovo hasn't officially released Windows 7 drivers for this laptop. I haven't tried with Vista or XP yet. What are others seeing? Update: For W500 owners w/ the 9 cell battery, what value do you see for "Full charge capacity" when on the Battery tab of the Power Manager utility? I see 81.87 Wh.

  Read the article

• WHEA_UNCORRECTABLE_ERROR BSOD - what is wrong?

  - by Arcane

  Hello I have a problem with my PC getting the WHEA_UNCORRECTABLE_ERROR bsod. It is a few months old pc. I am not overclocking or changing anything in bios, but sometimes (this is my third time) I get this bsod out of nowhere. This last time I was just watching some stream on twitch when the pc suddenly crashed. I have everything up to date in windows update and every other driver as well. Everything in Open hardware Monitor seems ok. Right now as of 10 min after the crash, the CPU temp is at 38°C, fans are at 1400RPM I am using Windows 8.1 Pro 64b. Here are my spec: Intel i5-4570 CPU @ 3.20GHz, Kingston HyperX 8GB DDR3 1600 XMP, GeForce GTX 660 with 340.52 drivers, Corsair VS450 power supply, Gigabyte GA-H87-HD3 you can see the BSOD dump here: https://www.dropbox.com/s/88i1q2nnqnpzux1/082514-29656-01.dmp?dl=0 Can anybody tell me what is wrong?

  Read the article

• Linux openSUSE 11.2 on VAIO Z890T

  - by alfredozn

  I have a VAIO Z-series (VGN-Z890T) and I want to install openSUSE 11.2. I found some guides to fix the problem for the video card switch, but all for older models, those preconfigured with windows vista. It looks like newer model use a different bios configuration to support hot swap between cards in Windows 7 and this change breaks the solution to my problem. I'm not an experienced linux user, but i was using it recently on my old computer ind definitively I want it on my laptop. I installed openSUSE once and i was trying and trying to solve it until I finished reinstall again and use a fresh installation. My question is: Does anyone has installed and configured successfully openSUSE on one of the latest vaio z laptops???

  Read the article

• How do you recommend installing Linux on a computer that has no external drive or ability to boot fr

  - by 7777

  I have an old Toshiba Portege 3505 "ultralight" laptop, meaning it doesn't have any kind of disk drive on it at all, that I'd like to completely reformat and install Linux on. However, it won't boot from any drive (and I don't have any on hand), so I'll have to install it from a USB drive (which I doubt it boots from either). (I'm not sure how to change the settings in my BIOS to get my computer to boot from a USB stick. Any ideas for this?) How do you recommend I do this? I want to note that I don't want to run Linux off a LiveUSB, I want to actually install it on the machine. I was thinking about Damn Small Linux, it's tiny and all I need. Any advice or suggestions for something else though? Finally, I'm a total newbie to this, I've never installed Linux on anything before so I might be a little slow on some stuff! Thanks!

  Read the article

• Installing Windows XP sp3 into USB 2.0 WD 320Gb Hard Drive

  - by NetKabuki

  I have a HP laptop with support for 3 USB 2.0 ports. I also have a clean 320Gb WD USB 2.0 drive. The HP can boot from USB (Bios options). I used the install disk (XP SP3 bootable) and after a few stutters, was actually able to load up a partition on the 320Gb drive with Windows. I cannot consistently get the system to boot up off the USB drive. I am able to drop Ubuntu on that same WD drive and boot up. I can even get Grub2 on Ubuntu to recognize the Win OS. But booting the Win OS is an impossible task. What can I do differently - if anything?

  Read the article

• Windows XP won't boot after drive transplant

  - by Nathan

  Hi all, I moved my hard drive from my Lenovo laptop into my Asus Eee PC netbook. When I started the netbook, after POST all I got was a black screen with a cursor in the upper left corner. I thought that the migration should work OK because this was a 32-bit version of Windows XP, and the Atom processor in the Asus should support the x86 instruction set. However, I don't know much about Windows, so maybe this was a dumb thought. I did verify that the BIOS can find the drive. It required major surgery to replace the drive, so any solution requiring me to remove the transplant drive is not going to fly. Keeping in mind that the netbook has no optical drive and that I have no other Windows computers (all my other computers run Linux), is there any way I can fix this problem? Thanks! Nathan

  Read the article

• How can I get data off of a Corsair SSD?

  - by user1870398

  My Corsair SSD won't work and I have some critical data on it that I didn't back up (I needed to create a copy of my mechanical storage device, just forgot). The drive isn't detected by the OS or BIOS. I also tried it on another system, but all that happened was the OS failed to load (my guess was that it knew the drive was there, just couldn't read it). I tried powering it on without the data cable for a bit of time to see if it'd work again, but it didn't. Any ideas of how I can get the data off of this drive without having to send it in?

  Read the article

• no display on tv when connecting pc via hdmi in win7

  - by Kane

  The system of pc is win7 32bit, the video card is ATI 4670. The tv is philips 74xx series. And the monitor is Dell 19' that connect with pc via VGA. The tv can receive the singal and show the pictures when booting the pc(bios self checking, the logo of windows 7), however the tv says there is no signal after the win7 login window shows. I have installed the latest CCC and driver of ATI video card. Does anyone have idea for it?

  Read the article

• taskmgr.exe 100% CPU Usage

  - by Burnsys

  Hi. I have 2 IBM servers Intel Xeon Dual core with 2gb RAM. the problem is that Taskmanager uses one full core when i open it. The same happens when i copy files in the explorer. OS: Windows 2003 Server Things i tried: Installed all updates They has kaspersky anti virus and they previously had Nod32. All drivers installed OK. All unused devices are disabled in the bios. Reinstalled win 2003 SP2. No conflict in drivers Tried opening via remote desktop and the problem continues. The cpu utilization is in the Kernel Times (Red in taskmanager) If i open Proces Explorer and i navigate to the threads consuming CPU the stack traces ends always in "NtkrnlPA!UnexpectedInterrupt", all threads stacks end in "UnexpectedInterrupt" ntoskrnl.exe!KiUnexpectedInterrupt+0x48 ntoskrnl.exe!KeWaitForMutexObject+0x20e ntoskrnl.exe!CcSetReadAheadGranularity+0x1ff9 ntoskrnl.exe!IoAllocateIrp+0x3fd ntoskrnl.exe!KeWaitForMutexObject+0x20e ntoskrnl.exe!NtWaitForSingleObject+0x94 ntoskrnl.exe!DbgBreakPointWithStatus+0xe05 ntdll.dll!KiFastSystemCallRet kernel32.dll!WaitForSingleObject+0x12 taskmgr.exe+0xeef6 kernel32.dll!GetModuleHandleA+0xdf Any help would be appreciated!

  Read the article

• Windows 7 using exactly HALF the installed memory

  - by Nathan Ridley

  I've taken this directly from system information: Installed Physical Memory (RAM) 4.00 GB Total Physical Memory 2.00 GB Available Physical Memory 434 MB Total Virtual Memory 5.10 GB Available Virtual Memory 1.19 GB Page File Space 3.11 GB Also the BIOS reports a full 4GB available. Note the 4gb installed, yet 2gb total. I understand that on a 32 bit operating system, you'll never get the full 4gb of ram, however typically you'll get in the range of 2.5-3.2gb of ram. I have only 2gb available! My swap file goes nuts when I do anything! Note that I have dual SLI nvidia video cards, each with 512mb of on board ram, though I have the SLI feature turned off. Anybody know why Windows might claim that I have exactly 2gb of ram total? Note: previously asked on SuperUser, but closed as "belongs on superuser" before this site opened: http://serverfault.com/questions/39603/windows-7-using-exactly-half-the-installed-memory (I still need an answer!)

  Read the article

• How to (hardware) RAID 10 on Ubuntu 10.04 LTS with 4 drives and motherboard with RAID contoller

  - by lollercoaster

  I have 4 500GB hard drives. I set up a RAID 10 in BIOS, much like shown here: http://www.supermicro.com/manuals/other/RAID_SATA_ESB2.pdf Then I followed these instructions: http://www.unrest.ca/Knowledge-Base/configuring-mdadm-raid10-for-ubuntu-910 Basically I cannot get it to work. I go through the instructions when I get to the "partition" section of the install, creating 4 RAID 1's (2 partitions on each drive, one for primary and one for swap space), then combining to make a RAID 10. Unfortunately it still shows 2 partitions, one 500 GB and another being 36GB for some reason. Any ideas? I think best would be if anyone had found good instructions (step by step) for how to do this...I've been googling for hours and haven't found anything...

  Read the article

• Stop chkdsk when Windows 7 on one drive and Windows 8 on another

  - by markmnl

  I installed Windows 8 (retail) on a new drive with my Windows 7 drive unplugged. So each Windows has no idea about the other one and I use the BIOS boot options to select which drive hence OS to boot into. Now whenever I boot into Windows 8 then boot into Windows 7, Windows 7 runs chkdisk presumably because Windows 8 messed with it. Is there anyway to stop this? (In hindsight I should have installed Windows 8 with Windows 7 drive plugged in so I could use the Windows dual boot options).

  Read the article

• Error in using DBAN on HDD

  - by John Watson

  I am using DBAN to erase HDD. DBAN is loaded from a CD and BIOS Boot order has been set to favour CD drive. On starting laptop, system boots from CD and DBAN interface can be seen. DBAN detects two storage devices, HDD and the SD Card. My HDD IS 320GB but DBAN says 298GB. It erases the SD card but when i try to erase HDD, it gives following error. DBAN finished with non-fatal errors. *ERROR /dev/sdb (process crash) *ERROR /dev/sda (process crash)

  Read the article

• Change from IDE to AHCI after installing Windows 8

  - by Louis

  I had my drive controller configured for IDE when I installed Windows 7. This didn't change when I upgraded to Windows 8. I now need to enable AHCI, but doing so causes Windows to fail to start. It doesn't know how to automatically fix the problem. I was able to use Regedit from the recovery area, in order to try using this fix that worked for Vista. That key is missing in Windows 8, however. I read that the relevant key is now in HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\storahci. But my settings already match the changes they suggest making. How can I get Windows to boot after enabling AHCI in the BIOS?

  Read the article

• Fedora 11 System - Failed Hard Drive Removed, and Boot gets GRUB Hard Disk Error

  - by user38030

  Greetings, I have a machine with a 120GB ATA drive that has what I thought to be non-essential data on it. I also have a 320GB SATA hard drive with the OS/Application/Files (good data I want to keep). My 120GB ATA is failing I believe, as my computer kept slowing to a halt. However, when I move the drive from BIOS my computer will not start, says "GRUB Hard Disk Error". I know that my Fedora system has an LVM setup. I am looking to just remove the 120GB drive from "the mix", and just have one hard drive. How do I recover ? Thank you. I have access to a Linux Live CD right now and can make any changes. However, it won't boot into my OS - it fails.

  Read the article

• Is There Anyway to Undo a Quick Initialize from a Perc6/i VD?

  - by Carlo71

  I stupidly fast initialized an existing Raid 5 Array Virtual disk with 10 Virtual Machines after creating a new Raid 5 Array. The VDs switched order on the list of the Perc Controller. My server is a PowerEdge R710 with a Perc 6/i Raid controller running ESXi 5.1. The Bios of the R710 and the Perc 6/i controller are both running the latest firmware. I tried the steps on this article: http://www.caseyfulton.com/dell-perc-6i-fast-initialize-how-to-restore/. However the BartPE just freezes on the Windows XP slapsh page. Does anybody know a full proof method? I have backups of the VMs, however I would like to avoid restoring all of them due to time constraint.

  Read the article

• Installation stops with cmd.exe window on Laptop

  - by Saariko

  I am installing W7 Ent on an LG R580. I am working with a valid ISO (installs perfect on other systems). During the installation, before the installation window, the process hangs, and I get a black, cmd.exe screen with the following: Select Administrator: X:\windows\system32\cmd.exe Microsoft Windows [Version 6.1.7601] with a prompt for: X:\windows\system32 My keyboard at that time only prints capital letters with '^' before each. Only thing that I am able to do is reboot. In the bios, I tried to disable USB Legacy ( thinking the problem is with my DVD ) - did not help.

  Read the article

• Windows Vista wont recognize SSD drive

  - by Spiros

  I just bought an SSD drive for my Vista (32bit) box (120GB OCZ Agility 3). Unfortunately windows vista won't display it in the my computer window, and generally wont let me work on it. However, the bios recognizes the SSD drive correctly, and when I go on the windows device manager the drive is there as well. I can see the device properties. On the volumes, when I click on populate, I have: Disk: Disk1 Type: Uknown Status: not initialized Partition style: not avaiable Unallocated space: 0MB Reserved space: 0MB Any ideas what could be wrong? Thanks

  Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >