Search Results

Search found 64639 results on 2586 pages for 'work stealing'.

Page 596/2586 | < Previous Page | 592 593 594 595 596 597 598 599 600 601 602 603  | Next Page >

  • iTunes Home Sharing only works one way between 2 WinXP PC's on the same LAN

    - by scunliffe
    Both PC's have the latest iTunes installed. PC (A) can "see" that there is a shared library "B library" but attempts to connect to it return this error message: The shared library "{Username}'s Library" is not responding (-3259) Check that any firewall software running on either the shared computer or this computer has been set to allow communication on port 3689. however the reverse works fine. e.g. PC (B) can "see" shared library "A library" and can access all content. Notes: Both PC's have Home Sharing enabled (turned off/on several times to verify). Both PC's have Windows Firewall turned on, but in the exceptions tab, iTunes is allowed, and Port 3689 is also added as a firewall exception (just in case) Both iTunes accounts have been "authorized" on both PC's Both PC's connect via LAN via D-Link DIR-615 router. In the advanced application rules, iTunes has also been added to allow traffic on port 3689 un-hindered. Is there any other magical setting/configuration option that I should be aware of and set in order to get this to work? I could care less about sharing apps etc. I just want the music sharing to work. Update: Solved! It turns out on PC (B) there were multiple accounts set up. 1 of the accounts had the checkbox checked under the windows firewall "On" option which states "No exceptions" thus even though it was added to the exception list on the main user account, this other account was blocking access.

    Read the article

  • How powerful of a PC do you need to edit HD videos?

    - by Xeoncross
    I have a Core2Quad Q8200 (2.3GHz) with 4GB of RAM, a 512MB PCIe video card, and a SATA-2 HD. Yet it still isn't fast enough to edit 720i/p video in Sony Vegas or Adobe Premiere/Aftereffects. My RAM usage never peaks over 1.6GB, but my CPU cores make it to 95% quick! Right now the preview panes in all these programs lag to bad to actually work on the videos. I get to see 1-3 frames every second or two! So how fast do I have to go? At what point will my CPU be fast enough to actually edit these videos? I have to assume that regular people and their regular sub $2k computers can actually work with this footage. Another way to answer this is, how fast is the PC you used to edit videos? Update: I'ts worth noting that now that I have Adobe Pre/AF CS4 I am more interested in getting that working than my older Vegas 6. If you didn't have to re-run RAM preview every, single, time you made one change it would be my answer. But since I like to test many filters and effects before choosing one - I have to re-render a 1-sec section of footage over-and-over and it drives me nuts waiting. Perhaps a motherboard with Dual Xeon chips or something would be able to handle this. It would probably be as much as a dual-crossfire setup and would also speed up other applications.

    Read the article

  • ESXi 4.0 Guests Locking up

    - by Brendan Sherwin
    I installed ESXi 4.0 on an HP Proliant g5 with a 64bit Xeon processor and took advantage of the free license as I work for a public school. I created two instances of server 2003 from scratch, one to be the DC, DHCP, the other to be a file server and DNS/DHCP backup. I had both guests up and running fine, setup my user accounts, transferred the data, etc etc. Once I joined a client machine to the domain, I would find that both of my Windows guests would lock up. Sometimes it would be for five or so minutes, once it was overnight. The "locked up" state means that as far I could tell, all services were stopped; dhcp no longer handed out IP's, DNS stopped working, I couldn't RDP into the server. The ESXi host, my HP server, was still running fine. VSphere was working, and I could look at the performance of the individual guests.I would try Powering off the hosts from inside VSPhere, and the hosts would start powering off, but get stuck at 95%, and stay that way, sometimes only for 10 minutes, others for hours. Several times I had to restart ESXi from it's console in order to restart my machines. Now, can anyone tell me what is happening, and how I can fix it, or take steps to prevent it? I hired a consultant to come take a look at it, someone who's experience and knowledge I trust, and he told me he had never seen anything like this ever before. He spoke to a friend of his who is VM certified, and he also said he had never heard of this issue. Thanks for your replies, and I'll do my best to respond ASAP. Currently, the server is powered off, and I've reinstituted my nine year old Server 2000 boxes, and I'm considering installing ESXi 3.5. Does anyone know a host created in 4.0 will work in 3.5? I'd really like to avoid having to rebuild those accounts! I know 4.0 works on this server, as I have another server in another school with the same exact hardware running 4.0 fine. Brendan

    Read the article

  • How to make DD-WRT router's (configured like a repeater) devices be accessible on LAN? (i.e. integrate DHCP for both routers)

    - by Annonomus Penguin
    I have a D-Link DIR-600-A1 router running DD-WRT (using the 601's firmware: except for the model number, they are near identical). It has an Atheros chip, so there is no "repeater" option. You can bypass this by setting the main radio as a client to the main router, and adding a virtual radio configured as an AP. You can then set up the credentials for connecting to the main router and allowing devices to connect to the repeater/router. I have a few devices on my network: Ethernet computers Server with Samba running WiFi devices connected to the main router I then wanted to add a repeater. I have a couple of other things on the repeater: WiFi Computer Other WiFi devices. Anyway, I wanted to connect my WiFi computer to the share on my server via Samba. However, for some reason, my router treats the main router as WAN, not another device. I've tried disabling the SPI firewall: However, that doesn't work. I've tried pinging my WiFi computer from my server. However, I can ping my server from my WiFi computer. AFAIK, they are on the same subset, just using different IPs: the main one uses 192.168.0.x and the repeater uses 192.168.1.x (starting at 100 for some reason). It seems as I need to configure my router(s) to work together for DHCP. I noticed there was a "DHCP forwarder" option, but I have no idea what that would do. A quick note: for some reason (that's beyond me) my ISP disabled the capability to bridge a WiFi to ethernet connection with the router they provide (something about PPPoE or similar...). The service rep I talked to when I was having issues after I changed ISPs said that, but they couldn't explain exactly what they were "blocking." How can I get DD-WRT to not treat the client connection as WAN and the router to recognize the devices connected to the repeater?

    Read the article

  • Error opening hyperlinks in Excel 2003

    - by richardtallent
    When clicking to follow hyperlinks from Excel, I'm now getting this error: Unable to open http://blah... Cannot download the information you requested. The hyperlinks in the Excel file are created using the HYPERLINK() formula. I use Google Chrome as my default browser. The web site in question uses Basic Authentication, and I've entered correct credentials when prompted (the dialog looked like an IE auth box, not Chrome's, but it's always been that way, even when it was working properly). This hasn't been an issue until recently. I'm guessing our IT department made some lame change to IE's configuration that is causing Office to not be able to open the URLs, despite having Chrome as my browser. Things I've checked already: URLs are good, they work fine when pasted manually into Chrome, IE, or Firefox. IE is not set to Work Offline (already found that suggestion on Google). I checked Program Access and Defaults and verified that Chrome is selected. Nothing in the URL requires URLEncoding, so it's no goofy issue with encoding I've had reports from some other users now and then about the same problem, but this is the first time I've experienced it myself.

    Read the article

  • Run Explorer in SYSTEM account on Windows Vista or 7 using Sysinternal’s psexec tool?

    - by Rob
    Has anyone been successful at launching an instance of Windows Explorer in the SYSTEM account on Windows Vista or 7? It is possible to do this on XP, but I haven't been able to get it to completely work in Vista or 7. Trying to launch Explorer as SYSTEM into session 1 (my user session) results in Explorer exiting immediately and returning an error code of 1. I can launch Explorer as SYSTEM into session 0 with the following command: psexec -i 0 -s explorer That will create an instance of explorer running as SYSTEM with a taskbar and start menu on the hidden session 0 desktop, but won't let you open a file browser window. If you switch to the hidden session 0 desktop and try to open an Explorer window from there to browse files, the following error message appears: "The server process could not be started because the configured identity is incorrect. Check the username and password." I have set the following registry key to 1 for my user account and the SYSTEM account: \Software\Microsoft\Windows\CurrentVersion\Explorer\Advanced\SeparateProcess There has got to be a way to make this work? If it is not possible, can anyone explain why? -Rob

    Read the article

  • How to deal with DELL support system?

    - by Nishant Kumar
    We have purchased a Dell Optiplex 9010 SSFV for our organization's work. Since the first installation two of the USB keyboard keys were not working properly. I had to press those keys two times simultaneously, on first time keys did not work and for for second time it printed two characters (as it were buffering first character.) Two keys that were not working properly: Hexangrave (Below the ESC key: `) Double Quotes (Left the enter key ") We registered our complaint with DELL and they suggested (with some hard to understand and weird ENGLISH accent) some test and tricks, such as switching to different ports, checking keyboard on different PC, and it worked well with diff. PC(with Windows 7 Home Premium installed). It was clear that it is an OS fault, hence they suggested to re-install OS. Problem began here, we have a project on the run and currently a video editing project setup on our system, so can't re-install system in hurry and also DELL persons were not providing any other solution such as updating keyboard driver, etc. Arguments I am a Software Engg. and don't think it is a feasible solution to re-install entire system for simple problems. This prob is coming since the fresh system installation, so I don't think it will solve the problem. Finally, I had to find solution myself and got it here, now I want to show my disappointment to dell persons or at least tell them that they should improve there support system to not advice to re-install entire system for that simple problems. Notes We have purchased 5 years NEXT business day support from DELL for around 8000 INR (Not for that kind of solutions from DELL). It is Dell India Support System. So can anyone tell me how to tackle dell support system officially, so that they will pay more attention in near future. Thanks

    Read the article

  • Running mod_php and suPHP same time

    - by BHare
    I recently went from Debian Lenny with 5.2.x and was able to use mod_php for any php files that were not located in /home/ and suPHP for all the php files that were located in /home/. I did this because I needed a default php.ini (given me all features of php) for my websites in /var/www/ and I didn't want to have to change the owner of all the .php files from root. I also had a default php.ini for all the /home/ php files without dangerous features. This was I had setup: <IfModule mod_suphp.c> <Directory /home/> AddType application/x-httpd-php .php .php3 .php4 .php5 suPHP_AddHandler application/x-httpd-php suPHP_Engine on suPHP_ConfigPath /home/shared/ </Directory> </IfModule> This was working perfect, but recently I upgraded to PHP to 5.3.5 from dotdeb (Lenny has no official php 5.3) . This had weird issues on lenny such as not display errors correctly and little tid bits. So I decided to upgrade from lenny to squeeze. Uninstalled php (along with it came suphp) and reinstalled with the new source. I now have 5.3.3-7 with Debian Squeeze but I cannot get mod_php and suPHP to run at the same time anymore. mod_php will always work and there are no errors in apache2 or suphp logs. If I disabled mod_php then suPHP will work. Is there thing I am doing wrong?

    Read the article

  • HP Storageworks 448 tape drive input/output error with Ubuntu

    - by Dan D
    I'm trying to set a backup to tape of a machine using flexbackup. However any attempt to write to the tape drive (via either flexbackup or just tar) results in "/dev/st0: Input/output error" The machine seems to recognise the drive (HP Storageworks Ultrium 448) and that there's a tape in it and "mt status" seems to work... "mt -f /dev/st0 rewind" or "erase" throw no errors... root@stor001:/# mt status SCSI 2 tape drive: File number=0, block number=0, partition=0. Tape block size 0 bytes. Density code 0x42 (LTO-2). Soft error count since last status=0 General status bits on (41010000): BOT ONLINE IM_REP_EN root@stor001:/# cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: DVDRAM GSA-4084N Rev: KS02 Type: CD-ROM ANSI SCSI revision: 05 Host: scsi2 Channel: 00 Id: 03 Lun: 00 Vendor: HP Model: Ultrium 2-SCSI Rev: S65D Type: Sequential-Access ANSI SCSI revision: 03 "tell" does however root@stor001:/# mt -f /dev/st0 tell /dev/st0: Input/output error Based on a forum post I found, I tried: root@stor001:/# dd if=/dev/zero of=/dev/nst0 bs=1024 count=10 10+0 records in 10+0 records out 10240 bytes (10 kB) copied, 5.0815 s, 2.0 kB/s which gave the person on the forum an error but seems to work for me. If anyone has any suggestions, I'm all ears...

    Read the article

  • Managing Many External Hosts Using EC2 and Route 53

    - by futureal
    Looking for a "best practice" answer to managing externally-addressable hosts using the combination of Amazon EC2 and Amazon Route 53, without using Elastic IPs for each host. In my scenario I will have 30+ hosts that need to be accessible from outside EC2, so directly using internal DNS will not work. In the past, I have addressed hosts by assigning an elastic IP to that host (let's say, 55.55.55.55) and then creating an associated A record. For example, let's say I want to create "ec2-corp01.mydomain.com" I might do: ec2-corp01.mydomain.com. A 55.55.55.55 300 Then on that EC2 instance, I would assign the Elastic IP of 55.55.55.55, and everything works fine. Of course, to make this work, I need to have one Elastic IP per instance, which is something I'd like to avoid if possible; I'd like the infrastructure to be more dynamic. So my thought is to try something like: Create a script that queries the internal EC2 tools to determine an instance's private hostname On instance boot, call that script to determine its hostname, and then using the command-line Route 53 interface to find and update that hostname to its current internal hostname Since the host will have a relatively low TTL (let's say 300 as above, or 5 minutes) it should take effect pretty quickly Is this a good idea? Is there a better or more widely accepted way to handle it? If it IS a good idea, what type of record should I be creating? A CNAME that points to the internal host, like ec2-55-55-55-55.compute-1.amazonaws.com? Is an A record better or worse? Thanks!

    Read the article

  • Mplayer no sound when playing some movies

    - by Ivan Peevski
    Ok, that's a bit of a strange problem, that somehow crept into my system. It used to work fine. Here is the problem as far as I can identify it. When I try to play certain video files with mplayer, there is no sound. As far as I can tell, it is only an issue with ac3 and dts sound tracks (using the ffmpeg decoder). Mplayer says: ========================================================================== Opening audio decoder: [ffmpeg] FFmpeg/libavcodec audio decoders AUDIO: 48000 Hz, 6 ch, s16le, 1536.0 kbit/33.33% (ratio: 192000->576000) Selected audio codec: [ffdca] afm: ffmpeg (FFmpeg DTS) ========================================================================== [AO_ALSA] Playback open error: Device or resource busy Failed to initialize audio driver 'alsa' Could not open/initialize audio device -> no sound. Audio: no sound (similar with ac3 sound, but using the ffac3 audio codec). Trying different audio output (-ao oss/pcm/sdl) doesn't fix the problem. The strange thing is that if I play these files directly with ffplay, they work fine. mplayer sound with mp3/ogg is fine My alsa configuration is standard (no /etc/asound.conf or ~/.asound*) OS: Linux Gentoo Mplayer: 1.0_rc4_p20100213 (SVN-r30554-4.3.4) FFMpeg: 0.5_p20601-r1 (SVN-r20601) Any other information I can provide?

    Read the article

  • How to add an SSH user to my Ubuntu 12 server to upload PHP files

    - by user229209
    I have an Ubuntu 12 VPS and wanted to create a user account to upload and download my PHP code. So when logged in as root I created a user "chris" and then created a directory /var/www/chris I want "chris" to be able to upload and run files to the /var/www/chris directory. Permissions for the chris dir look like this: drwxrwxr-x 2 root chris 4096 Aug 20 03:35 chris As root I created a sample file called abc.php and put it in the chris dir. It worked fine when I test it in a browser. I logged in as chris and uploaded a file called 1234.php. That did not work. I just got a blank PHP page. The code was identical in both files. So it is not the code. The permissions now look like this: -rw-r--r-- 1 root chris 59 Aug 20 03:34 1234.php -rw-r--r-- 1 root root 49 Aug 20 03:21 abc.php How do I alow the "chris" user to upload files and get them to work?

    Read the article

  • VPN Error 619: Behind Cisco Router WRT310N

    - by ty91011
    I've researched a lot on all the forums and this error is too generic for any of the proposed solutions to work. I'll try to give as much detail and tried solutions. I'm running a CentOS PPTP server behind a Cisco WRT310N Router. Multiple clients from outside with different OS have failed with the same error 619, along with turning off windows firewall and disabling antivirus. I believe this is a router and IP routing issue, and not a client issue. When I connect from a client on the same router as the VPN server, it works when I use the 192. network address- but doesn't work with the public IP address. I've tried telnet to port 1723 from an outside server and I get in. I've opened up the VPN port (1723) on the router, VPN udp port (500), and the GRE port (47) to route to the VPN server's ip. Also, the server's router is behind a DSL modem. I had a glimmer of hope when this site: http://www.chicagotech.net/casestudy/vpnerror619.htm suggested that the PPoE authentication should reside on the router and not the modem. But I still came up empty. So does anybody know what the problem is?

    Read the article

  • Drobo FS vs. MacBook Pro: Finder works, Drobo Dashboard doesn't

    - by dash-tom-bang
    Does anyone have any experience with the new Drobo FS, specifically using it from a MacBook Pro? My experience thus far is this: Set up the Drobo Dashboard software (hereinafter called simply 'Dashboard') on my WinXP machine, which is hard-wired to the network to do the data migration from my NAS-that's-being-replaced (a 250G SimpleShare which works well enough but I was always afraid of losing the one disk). The Dashboard seems to work ok, except that the DroboCopy function doesn't work at all. This is the backup solution, which I can configure, and if I launch it (e.g. to back up from the old NAS to the Drobo) it spins the NAS, seeking the drive all over hell and creation, until finally giving up an hour+ later with zero files copied. Selecting only a subset of the data yields the same effect albeit more quickly. On my Mac I installed the Dashboard software too, since most of my fiddling with the device will be from my couch in the living room. Finder connects to the box just fine, fwiw, but Dashboard just sits there, "waiting for connection." This is considerably more bothersome than the above paragraph, but I figured I'd give whatever information I have. Drobo is insisting that I send them this "Debug Log" file that their software generates. Does anyone know what's in it? It's encrypted and they won't tell me, which spooks me just a bit; not like I'm terribly concerned about privacy but I don't want to be sending personal information out to every clown who says they "need" it in order to help me. thanks a ton, -tom!

    Read the article

  • Installer not being updated ( probably because of Windows 7 file cache )

    - by Sithu Kyaw
    I'm creating an installer for my Visual FoxPro application using ISTool and Inno Setup. It is ok for me for the first time. But, I updated my code and re-built the EXE file. Then, compiled the installer again. I found that my update was not compiled into the installer and I did not see the update in my running application. I noticed that the EXE file, which was built by VFP, was updated properly. It seems the installation script did not output the updated file. But, when I changed folder names, it did work. I don't want to change folder names whenever I run that installation script. It is not a good idea actually. I think it is because of Windows 7 cache system. Mine is Windows 7 Home Premium Service Pack 1. For example, My previous output file is located at C:\path\to\myinstaller.exe When I compile the installation script, the output file there should be overwritten, but it was not as expected. Although I deleted the file, it did not work. When I changed to output file path as C:\newpath\to\myinstaller.exe, I got the fix, but it is not a solution what I'm looking for. Does anyone how to do that? [Edit] I found that the installed directory was not updated properly. For example, I installed the program to C:\Program files\MyInstalledApp When I run the installer again, that installation directory should be overwritten, but failed. Thus, I got to uninstall the app before I re-install it. Is there any fix for this?

    Read the article

  • Plesk wildcard subdomain not working

    - by avdgaag
    I'm trying to set up a wildcard subdomain on my VPS. Ultimately I want to end up with this: main site: my.domain.tld subdomain: sub1.my.domain.tld - should end up serving my.domain.tld/sub1 I am using plesk 8.6. I have created a DNS A record pointing at my VPS' IP. I have then restarted the DNS server and waited up to 24 hours. But trying ping sub1.my.domain.tld results in an unknown host error. So I know there's more stuff involved, configuring apache etc. But so far, I cannot even get the subdomain working at all, let alone serve up the right content. I have also tried a CNAME record, to no effect. I have also tried creating a regular subdomain with a fixed name, which also does not work. Pre-configured subdomains DO work, like ftp.my.domain.tld or mail.my.domain.tld. I am clearly missing something here, but my hosting provider charges a small fortune for any support request not involving hardware physically burning down, so I'm hesitant to ask them. Any ideas?

    Read the article

  • Apache > 2.2.22 rewrite rule not working?

    - by EBAH
    since yesterday I'm trying to figure out how to fix the following: running phpipam (http://www.phpipam.net/) with WAMP (Windows environment). The problem I am facing is related with RewriteRule functionality, so forget phpipam for a moment and concentrate on few lines of code. Here is the directory structure of my test website that emulate the first steps phpipam does (you can download http://goo.gl/ksvuGc): C:\wamp\www\rewrite-tst\ C:\wamp\www\rewrite-tst\.htaccess C:\wamp\www\rewrite-tst\index.php C:\wamp\www\rewrite-tst\install C:\wamp\www\rewrite-tst\install\index.php It seems that the following rewrite rule in .htaccess doesn't work: C:\wamp\www\rewrite-tst\.htaccess # install RewriteRule ^install$ install/ [R] RewriteRule ^install/$ index.php?page=install When opening C:\wamp\www\rewrite-tst\index.php the first step check the URL for "install" argument. Since the URL is: http://localhost/rewrite-tst no arguments are supplied and the browser is redirected to: header("Location: /rewrite-tst/install/") At this point the browser opens the page: C:\wamp\www\rewrite-tst\install\index.php >> http://localhost/rewrite-tst/install Apache, thanks to C:\wamp\www\rewrite-tst.htaccess should intercept this URL and redirect to: http://localhost/rewrite-tst/index.php?page=install Here are my tries: Win Apache 2.2.22: works Win Apache 2.4.4: KO Win Apache 2.4.6: KO In the attached zip file you can also find two traces from apache RewriteLog which I can't understand very well. Why Apache 2.4 doesn't work on Windows? Is it possible that there's a bug on Windows version of Apache (2.4.4 and 2.4.6) or am I wrong someway? Thanks for your help!!! Evan -- UPDATE 12 oct 2013 Now I'm really confused! Working on Linux, Kubuntu 13.04. Linux Apache 2.2.22: works Linux Apache 2.4.6: KO I guess there's something wrong in my rules at this point, or some change happened from Apache 2.2 to 2.4 ...

    Read the article

  • With a username passed to a script, find the user's home directory

    - by Clinton Blackmore
    I am writing a script that gets called when a user logs in and check if a certain folder exists or is a broken symlink. (This is on a Mac OS X system, but the question is purely bash). It is not elegant, and it is not working, but right now it looks like this: #!/bin/bash # Often users have a messed up cache folder -- one that was redirected # but now is just a broken symlink. This script checks to see if # the cache folder is all right, and if not, deletes it # so that the system can recreate it. USERNAME=$3 if [ "$USERNAME" == "" ] ; then echo "This script must be run at login!" >&2 exit 1 fi DIR="~$USERNAME/Library/Caches" cd $DIR || rm $DIR && echo "Removed misdirected Cache folder" && exit 0 echo "Cache folder was fine." The crux of the problem is that the tilde expansion is not working as I'd like. Let us say that I have a user named george, and that his home folder is /a/path/to/georges_home. If, at a shell, I type: cd ~george it takes me to the appropriate directory. If I type: HOME_DIR=~george echo $HOME_DIR It gives me: /a/path/to/georges_home However, if I try to use a variable, it does not work: USERNAME="george" cd ~$USERNAME -bash: cd: ~george: No such file or directory I've tried using quotes and backticks, but can't figure out how to make it expand properly. How do I make this work?

    Read the article

  • VMware vSphere Hypervisor 5 with Intel SPL 5000 in Raid 0 no boot from DVD?

    - by Richard
    I hope this is the correct StackExchange, since I am only using StackOverflow for Web development, but need some help with my server configuration. I would like to install VMware vSphere Hypervisor 5 on my server here at home and run a view machines on it such as Windows Server 2008 and Red Hat. I used to have either OpenSuse or Windows Server 2008 installed but I would like to get into VMWare Hypervisor. My hardware configuration: - Intel S5000PSL with bios version S5000.86B.10.60.0091 build date 10/09/2008 as of read out of bios - E5420 @ 2.5GHz Intel Xeon CPU The Intel Virtualization Technology is enabled in the BIOS - DVD DH20A4P DVD Writer - 8GB ECC Ram I have configured a RAID 0 on my 2 WD 2TB SATA drives I have burned the Hypervisor 5 on an empty DVD and it is bootable, I tested it on my client PC. The main problem here is basically, that I cannot boot the DVD on my server. I have set the Boot Option to the DVD drive. I have booted from the BIOS straight in the DVD drive and it does not work. I do not see any error messages. The only thing I see are the PXE error messages when it tries booting from the network and other devices, obviously without any result. Does anybody know why I cannot boot the DVD? What could cause the problem? I have sucessfully installed Windows Server 2008 via original DVD about 1 year ago, so the DVD drive can read and does work. The DVD drive is available in the BIOS and I have checked all cables and none of them is loose in any way. I even see the light flashing but it does not want to boot from the DVD. I am looking forward to suggestions and things that I should check. Thank you very much

    Read the article

  • Backing up VMs to a tape drive

    - by Aljoscha Vollmerhaus
    I've got myself one of these fancy tape drives, HP LTO2 with 200/400 GB cartridges. The st driver reports it like this: scsi 1:0:0:0: Sequential-Access HP Ultrium 2-SCSI T65D I can store and retrieve files like a charm using tar, both tar cf /dev/st0 somedirectory and tar xf /dev/st0 work flawless. However, what I really would like to backup are LVM LVs. They contain entire virtual machines with varying partition layouts, so using mount and tar is not an option. I've tried using something like dd if=/dev/VG/LV bs=64k of=/dev/st0 to achieve this, but there seem to be various problems associated with this approach. Firstly, I would like to be able to store more than 1 LV on a single tape. Now I guess I could seek to concatenate the data on the tape, but I think this would not work very well in an automated scenario with many different LVs of various sizes. Secondly, I would like to store a small XML file along with the raw data that contains some information about the VM contained in the LV. I could dump everything to a directory and tar it up - not very desirable, I would have to set aside huge amounts of scratch space. Is there an easier way to achieve this? Thirdly, from googling around it seems like it would be wise to use something like mbuffer when writing to the tape, to prevent what wikipedia calls "shoe-shining" the tape. However, I can't get anything useful done with mbuffer. The mbuffer man page suggests this for writing to a tape device: mbuffer -t -m 10M -p 80 -f -o $TAPE So I've tried this: dd if=/dev/VG/LV | mbuffer -t -m 10M -p 80 -f -d 64k -o /dev/st0 Note the added "-d 64k" to account for the 64k block size of the tape. However, reading data back from a tape written in this way never seems to yield any useful results - dd has been running for ages now, and managed to transfer only 361M of data from the tape. What's wrong here?

    Read the article

  • ssh X11 forwarding issue

    - by bbuser
    I have put ForwardX11 in my ~/.ssh/config and then I start a X11 application like this: ssh -f user@host 'someapp; sleep 1' This works fine. The application someapp has a button which opens a viewer application via a shell script viewer.sh. When I press the button the viewer comes up. This is all good and as expected, but if I do ssh -2 -f user@host 'someapp; sleep 1' there's trouble. someapp starts very well, but if I click the button the viewer doesn't show up. As the viewer is called via a shell script, I replaced the call with xclock and the situation was exactly the same - I think the viewer is not to blame. The situation is the same on Linux and AIX. The reason I need -2 is that I finally want to use connection multiplexing and this does only work with version 2. The reason for the sleep 1 is that it didn't work otherwise;-) To add more confusion, with ssh -2 -f user@host 'xterm &; app; sleep 1' the viewer works as long as the xterm is open. When I close xterm ssh -v outputs the following debug1: channel 1: FORCE input drain debug1: channel 0: free: client-session, nchannels 3 debug1: channel 1: free: x11, nchannels 2 and from that moment the viewer doesn't show when I press the button. I also replaced the viewer application with a script that writes the $DISPLAY variable to a file. The variable is always set correctly.

    Read the article

  • How to multiseat with HW 3d accel on CentOS 6.3 Final?

    - by user35070
    I would like to setup a multiseat configuration on CentOS 6.3 (two video cards, two keyboards, two mice, two monitors) and have hardware accelerated 3D on both monitors. 3D HW acceleration rules out Xephyr. I saw somewhere that recent versions of GDM (3.3 and newer?) don't support multiseat, so do I have to install KDM to make this work? If I just create a duplicate section with new device identifiers in my xorg.conf file, will this 'just work'? Using different ports on the same video card and separate keyboards, mice, and displays, the result was a desktop which spanned both monitors with both keyboards and mice acting as the same input in the GUI. I will power down and put in the new video card and report on the results soon. Both video cards are nvidia. UPDATE after putting in another NVIDIA video card, default behavior (before changing xorg.conf) is that one screen works normally, and both mice and keyboards are connected to it. Changing xorg.conf and the display manager to KDM and following the directions here https://help.ubuntu.com/community/MultiseatX#Ubuntu_10.04_.28Lucid.29 , I have 2 mirrored screens connected to separate video cards, DRI enabled, and 2 mice both connected to the same pointer. Keyboards don't do anything, however, I probably just need to fix a setting in xorg.conf I would still like to get multiseat functionality, eg. separate screens with separate input devices I have verified that the separate X processes are running (see page above) using 'ps aux | grepX [01]'

    Read the article

  • How to configuration keepalived on Amazon EC2?

    - by oeegee
    I rad some article. Keepalived over GRE tunnel for failover on VPS environment http://blog.killtheradio.net/how-tos/keepalived-haproxy-and-failover-on-the-cloud-or-any-vps-without-multicast/ but, I don't know how to configuration? and How to call this architecture? only I Know that How to config Master/Backup configuration at keepalived. What I want to know that How does work keepalived? I want to design this.... XMPP Server(EC2) | ------------------------------------------------- keepalived Master(EC2) - keepalived Backup(EC2) HAProxy #1 HAProxy#2 ------------------------------------------------- | Casandra#1 Casandra#2 Casandra#3 Casandra#4 Thanks! but What I want to know how to work on keepalived with unicast patche modul. ELB is expansive. and this is first totaly design. [Flow] ELB -- XMPP Server -- ELB -- Casandra ELB | XMPP#1 XMPP#2 XMPP#3 XMPP#4 | ELB | Casandra#1 Casandra#2 Casandra#3 Casandra#4 and change first design. [Flow] ELB -- XMPP Server -- HAProxy Master(Casandra Farm) -- Casandra ELB | XMPP#1 XMPP#2 XMPP#3 XMPP#4 | ------------------------------------------------- keepalived Master(EC2) - keepalived Backup(EC2) HAProxy#1 HAProxy#2 ------------------------------------------------- | Casandra#1 Casandra#2 Casandra#3 Casandra#4 this is second. [Flow] ELB -- HAProxy(XMPP Farm) -- XMPP Server -- HAProxy(Casandra Farm) -- Casanda It's OK? ELB | HAProxy#1 HAProxy#2 HAProxy#3 HAProxy#4 XMPP#1 XMPP#2 XMPP#3 XMPP#4 | Casandra#1 Casandra#2 Casandra#3 Casandra#4

    Read the article

  • Can I make two wireless routers communicate using the wireless?

    - by Dana Robinson
    I want to make a setup like this: cable modem <-cable- wireless router 1 <-wireless- wireless router 2 in another room <-cables- PCs in another room Basically, I want to extend my network access across the house and then have a bunch of network jacks available for my office PCs. Right now, I have a cable modem going to a wireless router in one room and a PC with a wireless PCI card in it in the office on the other side of the house. I use internet connection sharing with the other PCs in the office. The problem is that ICS is flaky, especially when I switch to VPN on the Windows box to access files at work. I picked up a wireless USB adapter that I thought I could share among the PCs I work on but I'm not very happy with it so I'm going to return it (NDISwrapper support for it is poor). Is this possible? My wireless experience so far has been pretty straightforward so I have no idea what kind of hardware is available. I've looked at network extenders but those just look like repeaters for signal strength. I want wired network jacks in my office.

    Read the article

  • Attempts at NIC teaming on Server 2008 R2 with PRO/1000 MT

    - by Klaus
    I have a Dell PowerEdge 1850 server and a gigabit switch that supports nic teaming (and was configured to do so). The server has a total of four Intel PRO/1000 MT ports, which also support teaming. But.. for some reason Intel does not actually have a version of the drivers/ProSet that will work for these cards on 2008 R2. You have to use the built-in drivers that come with 2008 R2, which do not support the additional features. According to their website, they have no plans to change this. Strangely enough, I experimented with various drivers in an attempt to force it to work. At one point, the teaming was working, but there were side effects (such as the DNS server refusing to start). So now I am back to running just one of the cards, (very) frustrated about the whole situation. I have looked all over to see if there is some way around this, but have not had any success. I know I can probably just get a new network adapter for it, but with the good deal I got, that would cost more than the server! :) While staying with 2008 R2, does anyone know of any possible alternatives? Thanks!

    Read the article

< Previous Page | 592 593 594 595 596 597 598 599 600 601 602 603  | Next Page >