Search Results

Search found 9015 results on 361 pages for 'wireless range'.

Page 60/361 | < Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >

• Access points fighting for dominance?

  - by Phillip Oldham

  We have a small office with a large number of wireless devices (a mixture of desktop machines, laptops, and wifi-enabled phones) all working from a single Apple Airport Extreme which extends our wired network. I've added another Airport Extreme for resiliency, since we've been seeing a decrease in performance and (as far as I understand) access points can only handle a small number of clients. I set the new AP to extend the current network so that the clients weren't constantly switching between different wireless networks, however as soon as this AP was configured all the wireless devices started seeing network trouble, flicking on and off. I'm assuming that this is because both APs are reasonably strong, and the client can't decide which to use. What is the best route to follow to resolve this? What I'm aiming for is wireless resiliency; preferably having two APs share the network load, or if this isn't an option then having a primary AP with a "fail-over", should the primary go down for any reason.

  Read the article

• Turning off the wi-fi functionality of a Netgear WNR2000

  - by indyK1ng

  Hello all, So my school has set up a ton of wireless access points and now they want me to turn off the wireless functionality of my router. I have a Netgear WNR2000 and I can't find the option to turn off the wireless. Thank you for your help

  Read the article

• Dial-in VPN Routing issue when on 192.168.x.x network range

  - by Ian

  I'm not an expert on networks but have a small office on the 192.168.x.x. range which is managed by a vigor (2800) router. I have enabled the VPN dial-in option on the router so I can get to the server on 192.168.1.100 which works fine from my macbook when i'm NOT on a local network with that is on the 192.168.x.x range. e.g. works fine when I tether over my Android smartphone but when I try & connect when on my home network, it connects, I can access the router (192.168.1.1) but cannot access 192.168.1.100 - traceroute doesn't hop via 192.168.1.1 I have enabled "send all traffic over VPN connection but again, not joy... Feels like the osx platform isn't routing the traffic out to the vpn endpoint as the destination address is on the local subnet but expect it would be. This work fine on a windows PC on the same home network. Any thoughts on what the issue could be?

  Read the article

• Bridging networks problems

  - by Eric

  In my setup I have 3 computers and 2 (wireless d-link) routers. Computer1 has ethernet and wireless interfaces ethernet : 192.168.0.x (DHCP) wireless : 192.168.10.254 (static) Computer 2 has ethernet with two ips ethernet1 : 192.168.0.90 (static) ethernet2 : 192.168.10.110 (static) Computer 3 is a particular device with a hardcoded ip that I can't change wireless : 192.168.10.41 (static) Router1 manages internet and DHCP for network 192.168.0.0/24 Router2 is more complicated. I don't use DHCP. I use it to bridge between both networks. Its static ip is 192.168.10.1 Computer1 can ping Computer2. Computer1 can ping Computer3. Computer1 can ping Router1. Computer1 cannot ping Router2. Computer2 cannot ping Computer3. Computer2 can ping Router2. Router1 can ping Router1 Router2 can ping Computer2 Router2 cannot ping Computer1 Router2 cannot ping Computer3 This is very weird. Router2 manages the wireless connection, it should be able to ping its own computers right? My question is obviously : How can I make it so Computer2 can access everything else. This is a traditional case of "it was working before christmas and now it doesn't". The ethernet wiring is as follow : [ Computer1 ]----[ Router1 ]---[ Router2 ]---[ Computer3 ] I am using switch (lan) ports on Router1/2.

  Read the article

• Can I use an apple airport express as a wired bridge?

  - by Chris

  I have a wireless network using an Apple Airport extreme. That device is set up in my office and hooked up to the cable modem. I have a TV in another room which can accept a wired internet connection (not wireless enabled). Can I use an Apple airport express's ethernet jack to create a wireless to wired bridge? If not what device would I use to do the same thing?

  Read the article

• Windows 7/8 can't connect to an N Router

  - by xenoterracide

  I have a router running OpenWRT backfire, with N and A/B/G being broadcast. A linux laptop, and a Mac laptop can see the N network and connect to it (or at least they could last weekend). But there is now a Windows 7 Desktop with a B/G/N wireless card, and a Windows 8 Laptop with a B/G/N wireless card that can't see the N network only the B/G broadcast. The B/G and N have different SSID's and Encryption ( WEP and WPA2 PSK respectively ). The N SSID isn't even visible. Does anyone have any suggestions as to how to troubleshoot further? Or what might be the cause? update wireless info Desktop Dell Wireless 1502 802.11b/g/n Atheros Communications Inc 9.2.0.412

  Read the article

• Network configuration with limited hardware

  - by Pavel

  I have cable internet and I have two PC. One of them has wireless and ethernet, the other pc has ethernet only. Also, I have a dsl modem that has wireless builtin (some common speedstream model). My goal is to connect all of them so that both have internet access. As I understand, I have two options: connect speedstream to the cable and then connect other PC's to speedstream; OR, connect pc with wireless to the cable and then connect the other pc that has ethernet only using ethernet+wireless through speestream. First one seems to be easy, but it doesn't seem to work. What about the other choice? Is it possible to do it?

  Read the article

• How do I turn a Wi-Fi "hotspot" into a local wired network?

  - by Max Schmeling

  Here's the situation: In a remote "office" I have a computer with no network connection, that I need to network with when I'm at this remote office. There is a wireless network where this computer is, but no wireless adapter in the computer. I have a laptop running Windows 7 that can connect to the wireless, and the computer is running Windows Vista. What is the best way to get them both connected? I know I can buy a USB wireless adapter or something for the computer, but is there an easy way to do it with what I've got?

  Read the article

• How can I access my external hard drive wirelessly from my laptop?

  - by leora

  My desktop crashed so I am migrated over to a laptop. I have wireless in my home so i am trying to be able to use to laptop in any room without any other connections (wireless printer, wireless mouse, etc) The one issue i have is that my desktop had 2 external hard drives (USB) connected to them and i am trying to figure out the best way to treat these as external drives without having to plug them into the laptop directly. My external hard drive is the Western Digital WDH1U5000N 500GB and my laptop is a Dell D620.

  Read the article

• Windows 7 unidentified network (or limited access) after hibernate.

  - by null

  My windows 7 network will show limited access or unidentified network after coming up from hibernation. In the office I normally use LAN connection, I turn-off my wireless card (DELL Latitude has on/off switch for the wireless card). When I back at home I will turn on the wireless card, but it will take about 15 seconds to detect my home WIFI and then show limited access. I will have to restart the notebook and it will be able to connect to my WIFI and internet. The problem will be solved if I restart the notebook, but that defeats the purpose of hibernation doesn't it? I have tried uninstalling the wireless card driver but still does not solve it. I also tried updating my network card driver but windows says I am using the latest driver. On support.dell.com also showing I am using the latest driver.

  Read the article

• How can I work out how many IP addresses there are in a given range?

  - by Jarede

  I'm wondering if there is a formula to work out the amount of IP addresses in a given range. I have a system that takes either a single IP address or a start and and end IP address: A single one might be: 145.16.23.241 A range might be: 145.16.23.122 - 145.16.23.144 The people inputting these aren't technical, nor are they receiving these details from technical people, so suggesting using CIDR notation isn't an answer for me. I want to be able to highlight that when entering a range such as: 122.100.10.12 - 128.10.200.140 it might not actually be a range and rather 2 singular IP addresses since such a range would comprise of x (large number of) IP addresses. Is there a basic formula to help me highlight this?

  Read the article

• Meraki wireless access point disconnects clients

  - by resolver101

  We have a Meraki MR16 Cloud Managed AP and it disconnects certain clients. The clients with Intel wireless cards work without any disconnects. The Meraki reports the follow in its event log: Sep 4 09:55:47 WPA authentication Sep 4 09:55:47 802.11 association channel: 11, rssi: 64 Sep 4 09:55:38 802.11 disassociation client has left AP Sep 4 09:55:38 WPA deauthentication vap: 0, radio: 0, aid: 1633956416 An example wireless network card which the Meraki disconnects is Realtek RTL8191SE 802.11b/g/n WiFi Adapter. The realtek laptop is sat 2 meters away from the AP and has a lot of signal and the Meraki reports minimal interference. Any ideas why it disconnects non-intel wireless network cards?

  Read the article

• How to bridge multiple wireless access points (and internet entry points) into one network

  - by amccormack

  I have two DSL lines coming in to wireless access points and then running to a RV082 Gateway/Bridge. The gateway then runs to a switch, which runs to multiple PCs and a Printer (See picture below). Normally, I would set up the wireless access points behind the gateway, but they are also the modems for the dsl. I have found that I can not print to the network printer if I am connected to the wireless network, but only if I am connected to the wired network. How can I configure the Gateway and APs (Routers) so that the PCs and Printer are all on the same internal network? I have tried turning DHCP off or redirect on the APs and redirect them to the Gateway. However, neither of these worked. Furthermore, I tried pinging the Gateway from the AP but got no response.

  Read the article

• How to go about scheduling a task in windows 7 to change wireless connection

  - by Skindeep2366

  This may or not be something that can be done. I cannot find anything on the wireless connection manager built into windows 7 let alone methods for passing params into it. Problem is as follows: I have 2 wireless routers. One provides internet access, the other provides sole access to the local network. Every day at 4am the main system creates a backup in 2 locations. One is a External usb drive, the other is a location on the network. This is all cool if it is remembered to change over to the local network router before leaving. But if it is forgotten the roof will collapse, the walls will burn, and I will be... well you get the idea. Solution: there is already a custom event that fires a automated backup program at 4am everyday. I need someway to force the wireless network to use the correct connection at say 3:58am everyday. Any ideas????

  Read the article

• Ubuntu problem not connecting to wireless or wired network

  - by ToughPal

  I recently installed openvpn and things were working. But I got a weird screen after a few hours and on restart my wired and wireless connections are not working. Can someone help? cat /etc/network/interfaces auto lo iface lo inet loopback cat /etc/resolv.conf #Generated by NetworkManager Is there anything missing? I tried both wired and wireless and both are not working. Usually if I ever have a problem with wireless, the wired always work! My /etc/network/interfaces is looking wrong. Can you please send me yours? I am using ubuntu 9.10 and the internet was working correctly until today! Please help

  Read the article

• Enable/disable wireless interface in a bat file

  - by Herms

  Is there a way to enable/disable a wireless network interface via the command line (so I can put it in a bat file)? When I'm in the office I use a wired connection, but Windows still occasionally bugs me about my wireless connection not being connected (even though I turned off the option for notifying me when there's no connectivity). I'm guessing the only way to stop it from bugging me is to disable the interface, but I'd rather not have to go into the network settings every time I need to do so. I'd like to set up a bat file or a shortcut that I can use to enable/disable the wireless (preferably a single one that toggles the current state), and then just set up a keyboard shortcut for that. I just have no idea how to do so from the command line.

  Read the article

• Cannot install wireless lan service on windows 2012 RTM offline

  - by user1763118

  I'm having trouble installing the wireless lan service offline with a fresh installed windows 2012 server RTM. I tried "install-windowsfeature wireless-networking" in the non-gui mode and using the server manager in the gui mode to enable the wireless lan service, but both of them show a "failure configuring windows updates" message after the installation restarted the system. I checked the event log and I think messages about "The WLAN Autoconfig service depends on the following service: nativewifip. This service might not be installed" are the source of the issue. Google shows it is a service called "native wifi filter", but I cannot find anywhere to install that service. I don't have a Ethernet adapter for that computer, so have to install everything offline before the wifi's working.

  Read the article

• Determining Maximum Txpower a WiFi Card Supports?

  - by BigGenius

  I have a Atheros R9285 wifi card. How can i determine , what is max. Txpower it can support? biggenius@hackbook:~$ iwconfig lo no wireless extensions. wlan0 IEEE 802.11abgn ESSID:"Default" Mode:Managed Frequency:2.437 GHz Access Point: 00:08:5C:9D:4F:40 Bit Rate=2 Mb/s Tx-Power=35 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:on Link Quality=24/70 Signal level=-86 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:140 Invalid misc:247 Missed beacon:0 eth0 no wireless extensions. biggenius@hackbook:~$ iw phy0 info Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 2412 MHz [1] (35.0 dBm) * 2417 MHz [2] (35.0 dBm) * 2422 MHz [3] (35.0 dBm) * 2427 MHz [4] (35.0 dBm) * 2432 MHz [5] (35.0 dBm) * 2437 MHz [6] (35.0 dBm) * 2442 MHz [7] (35.0 dBm) * 2447 MHz [8] (35.0 dBm) * 2452 MHz [9] (35.0 dBm) * 2457 MHz [10] (35.0 dBm) * 2462 MHz [11] (35.0 dBm) * 2467 MHz [12] (35.0 dBm) * 2472 MHz [13] (35.0 dBm) * 2484 MHz [14] (35.0 dBm) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Band 2: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT TX/RX MCS rate indexes supported: 0-7 Frequencies: * 5180 MHz [36] (35.0 dBm) * 5200 MHz [40] (35.0 dBm) * 5220 MHz [44] (35.0 dBm) * 5240 MHz [48] (35.0 dBm) * 5260 MHz [52] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5280 MHz [56] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5300 MHz [60] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5320 MHz [64] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5500 MHz [100] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5520 MHz [104] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5540 MHz [108] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5560 MHz [112] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5580 MHz [116] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5600 MHz [120] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5620 MHz [124] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5640 MHz [128] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5660 MHz [132] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5680 MHz [136] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5700 MHz [140] (35.0 dBm) (passive scanning, no IBSS, radar detection) * 5745 MHz [149] (35.0 dBm) * 5765 MHz [153] (35.0 dBm) * 5785 MHz [157] (35.0 dBm) * 5805 MHz [161] (35.0 dBm) * 5825 MHz [165] (35.0 dBm) Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Supported Ciphers: * WEP40 (00-0f-ac:1) * WEP104 (00-0f-ac:5) * TKIP (00-0f-ac:2) * CCMP (00-0f-ac:4) * CMAC (00-0f-ac:6) Available Antennas: TX 0x1 RX 0x3 Configured Antennas: TX 0x1 RX 0x3 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO software interface modes (can always be added): * AP/VLAN * monitor valid interface combinations: * #{ managed, WDS, P2P-client } <= 2048, #{ AP, mesh point, P2P-GO } <= 8, total <= 2048, #channels <= 1 Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * Unknown command (82) * Unknown command (81) * Unknown command (84) * Unknown command (87) * Unknown command (85) * testmode * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 Device supports RSN-IBSS.

  Read the article

• Dell 3721 Wifi problem Ubuntu 13.04

  - by Sebastian

  I have a Dell 3721 which comes original with windows 8. I managed it to install ubuntu 12.10 on this laptop, even there was no out of the box drivers. With 12.10 I was forces to install this .deb package couple of times. After installing it, it was ok for some weeks before I have to install it again. Maybe some security updates destroy something which made in necessary to install it again... http://jas.gemnetworks.com/debian/pool/main/w/wireless-bcm43142/wireless-bcm43142-dkms_6.20.55.19-1_amd64.deb My problem is, that this package isnt working with ubuntu 13.04 anymore. So I cant use Wifi now. Also my display is almost dark, I cant change the brightness level with ubuntu 13.04. Hope you can give me some advice. Dell:~$ sudo lspci -nn 00:00.0 Host bridge [0600]: Intel Corporation 3rd Gen Core processor DRAM Controller [8086:0154] (rev 09) 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) 00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) 00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04) 00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) 00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04) 00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) 00:1c.1 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 2 [8086:1e12] (rev c4) 00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) 00:1f.0 ISA bridge [0601]: Intel Corporation HM76 Express Chipset LPC Controller [8086:1e59] (rev 04) 00:1f.2 SATA controller [0106]: Intel Corporation 7 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e03] (rev 04) 00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04) 01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller [10ec:8136] (rev 05) 02:00.0 Network controller [0280]: Broadcom Corporation BCM43142 802.11b/g/n [14e4:4365] (rev 01) @Dell:~$ lsusb Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 003: ID 0a5c:21d7 Broadcom Corp. Bus 001 Device 004: ID 0bda:0129 Realtek Semiconductor Corp. Bus 001 Device 005: ID 0c45:64ad Microdia @Dell:~$ lspci -nn | grep VGA 00:02.0 VGA compatible controller [0300]: Intel Corporation 3rd Gen Core processor Graphics Controller [8086:0166] (rev 09) @Dell:~$ sudo lshw -class network *-network Beschreibung: Ethernet interface Produkt: RTL8101E/RTL8102E PCI Express Fast Ethernet controller Hersteller: Realtek Semiconductor Co., Ltd. Physische ID: 0 Bus-Informationen: pci@0000:01:00.0 Logischer Name: eth0 Version: 05 Seriennummer: xx:xx:xx:xx:xx:xx Größe: 100Mbit/s Kapazität: 100Mbit/s Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation Konfiguration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8105e-1.fw ip=192.168.2.103 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s Ressourcen: irq:42 ioport:2000(Größe=256) memory:c0404000-c0404fff memory:c0400000-c0403fff *-network UNGEFORDERT Beschreibung: Network controller Produkt: BCM43142 802.11b/g/n Hersteller: Broadcom Corporation Physische ID: 0 Bus-Informationen: pci@0000:02:00.0 Version: 01 Breite: 64 bits Takt: 33MHz Fähigkeiten: pm msi pciexpress bus_master cap_list Konfiguration: latency=0 Ressourcen: memory:c0500000-c0507fff

  Read the article

• Javascript: I can get the text of a selection, now how do I get the text outside the selection?

  - by DavidR

  I have a bit of code that returns the text of a selection and I can assign that string to a variable, but now all I need are two variables, one for the text before the selection and one for the text after the selection. Here is the code for getting the selection: function findSelection(){ //returns the selection object. var userSelection; if (window.getSelection) {userSelection = window.getSelection();} // Mozilla Selection object. else if (document.selection){userSelection = document.selection.createRange();} //gets Microsoft Text Range, should be second b/c Opera has poor support for it. if (userSelection.text){return userSelection.text} //for Microsoft Objects. else {return userSelection} //For Mozilla Objects. } Then I find the anchorOffset and focusOffset to find the caret positions. I tried using these to modify a range object, like this: var range = document.createRange(); range.setStart(textdiv,0); range.setEnd(textdiv,5); Where textdiv is a variable holding the last div the user clicked on. The problem is firefox just gives me a "Security error" code: "1000" at the line range.setStart(textdiv,0);. Is there an easier way to go about doing this? I really just need the text and nothing more.

  Read the article

• Weird Excel Formatting

  - by Gage

  Recently a new co-op was hired at our company and has been tasked to run a report. The report queries the database and returns a resultset and from there procedes to create the spreadsheets. Depending on the number of days selected a different number of reports are generated but I do not believe that is relavent to the question. Basically it runs the reports and loops through the resultset but at some point continues to loop through until tow 65536 at which it stops. For Example if the resultset contained 74 records then the first 74 rows would appear normally (formatted yellow) while everything after that would also be formatted yellow although it should be left alone. I am inheriting this code as I to am a new co-op. Apparently this only happens when a "change of guards" happens (New co-op has to run the report).` DoCmd.SetWarnings False DoCmd.OpenQuery ("DailySummaryQueryMain") strSQL = "SELECT * FROM DailySummaryMain" Set rs = CurrentDb.OpenRecordset(strSQL) DoCmd.Echo True, "Running first Report" If Not rs.EOF Then rs.MoveFirst Do While Not rs.EOF And Not rs.BOF xlapp.Range("A" & i).Value = rs.Fields(0).Value xlapp.Range("B" & i).Value = rs.Fields(1).Value xlapp.Range("C" & i).Value = rs.Fields(2).Value Set rs2 = CurrentDb.OpenRecordset("SELECT dbo_StatusType.StatusTypeID, dbo_StatusType.Name FROM dbo_StatusType WHERE (((dbo_StatusType.StatusTypeID)=" & rs.Fields(3) & "))") rs2.MoveFirst xlapp.Range("D" & i).Value = rs2.Fields(1).Value xlapp.Range("E" & i).Value = rs.Fields(4).Value xlapp.Range("F" & i).Value = rs.Fields(5).Value xlapp.Range("G" & i).Value = rs.Fields(6).Value 'count number of outages that start and end on same day If Format(xlapp.Range("F" & i).Value, "mm/dd/yyyy") = Format(xlapp.Range("G" & i).Value, "mm/dd/yyyy") Then dayCount = dayCount + 1 End If xlapp.Range("H" & i).Value = rs.Fields(7).Value xlapp.Range("I" & i).Value = rs.Fields(8).Value xlapp.Range("J" & i).Value = rs.Fields(9).Value xlapp.Range("K" & i).Value = rs.Fields(10).Value xlapp.Range("L" & i).Value = rs.Fields(11).Value xlapp.Range("M" & i).Value = rs.Fields(12).Value xlapp.Range("N" & i).Value = rs.Fields(13).Value 'highlite recently modified rows If rs.Fields(14).Value = "Yes" Then xlapp.Range("A" & i & ":N" & i).Select With xlapp.Selection.Interior .ColorIndex = 36 .Pattern = xlSolid End With End If 'break apart by sector If CInt(rs.Fields(2).Value) = 1 Then row = row1 ElseIf CInt(rs.Fields(2).Value) = 2 Then row = row2 ElseIf CInt(rs.Fields(2).Value) = 3 Then row = row3 Else row = row4 End If xlapp.Worksheets(CInt(rs.Fields(2).Value) + 1).Activate xlapp.Range("A" & row).Value = rs.Fields(0).Value xlapp.Range("B" & row).Value = rs.Fields(1).Value xlapp.Range("C" & row).Value = rs.Fields(13).Value xlapp.Range("D" & row).Value = rs.Fields(4).Value xlapp.Range("E" & row).Value = rs.Fields(5).Value xlapp.Range("F" & row).Value = rs.Fields(6).Value xlapp.Range("G" & row).Value = rs.Fields(7).Value xlapp.Range("H" & row).Value = rs.Fields(8).Value xlapp.Range("I" & row).Value = rs.Fields(9).Value xlapp.Range("J" & row).Value = rs.Fields(10).Value xlapp.Range("K" & row).Value = "" xlapp.Range("L" & row).Value = rs.Fields(11).Value xlapp.Range("M" & row).Value = rs.Fields(13).Value If CInt(rs.Fields(2).Value) = 1 Then row1 = row1 + 1 ElseIf CInt(rs.Fields(2).Value) = 2 Then row2 = row2 + 1 ElseIf CInt(rs.Fields(2).Value) = 3 Then row3 = row3 + 1 Else row4 = row4 + 1 End If 'activate main summary sheet for next outage xlapp.Worksheets(1).Activate i = i + 1 rs.MoveNext Loop` Also I should note that this is all happening within an access database which has its tables linked from SQL. The query is extremely slow to run from which I believe is the use of views but thats neither here nor there. All you have to know is attempting to debug takes an enormous amount of time due to having to wait for the recordset to return. My guess is that its not checking to see if the resultset is empty correctly. Is there a way I could check to see if theres a value is rs.Fields(0) and base it off that maybe? That is the ID column and there should always be a value. I am wondering why rs.EOF isn't catching this though.

  Read the article

• Wifi Direct P2P-go and P2P-client support in ubuntu

  - by giri

  I am trying to get wifi direct working on a laptop with ubuntu 12.04 When I type the command 'iw list' it doesn't show P2P-client or P2P-go under 'supported interface modes.From http://wireless.kernel.org/en/users/Documentation/iw/replace-iwconfig I found that 'iwconfig' was replaced with 'iw'.Does it mean that my hardware doesn't have support for wifi-direct or is it just the software(drivers) issue? If is it just sofware issue please help me to find the right drivers which support wifi-direct. Here is the info about my ethernet controller from the output of 'lspci' 02:00.0 Ethernet controller: Atheros Communication Inc. AR242x / AR542x Wreless Network Adapter (PCI-Express) (rev 01) 06:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8055 PCI-E Gigabit Ethernet Controller (rev 13)

  Read the article

• How can I get a Belkin N600 DB (F9L1101v1) to work on Ubuntu 12,04 64-Bit

  - by rheide

  I could use some assistance to trying to get a Belkin N600 DB Wireless Dual-Band USB Adapter to work on a Dell Inspiron 1525 with 64-Bit Ubuntu 12.04. The device won't work out of the box. Tried to go the NDISWrapper route, but using the GUI, received the following message: Module could not be loaded. Error was: FATAL: Module ndiswrapper not found. Is the ndiswrapper module installed? Despite the fact that it showed up listed in the GUI, the device still did not function properly. How should I proceed from here?

  Read the article

• wpa_supplicant ioctl[SIOCSIWENCODEEXT]: Invalid argument

  - by RobinJ

  I just installed Ubuntu Server on a spare computer with a broken graphic card, and I needed to setup my wifi. I thought No problem, I've done it before from the command line, in Arch Linux., only the steps I had to take in Arch Linux didn't work in Ubuntu Server (that's odd, wasn't Ubuntu supposed to be so much more user-friendly? :/). This is what I'd normally do: ip link set wlan0 up wpa_passphrase <ESSID> <WPA KEY> > /etc/wpa_supplicant.conf wpa_supplicant -B -Dwext -i wlan0 -c /etc/wpa_supplicant.conf dhcpcd wlan0 Only at the wpa_supplicant I get some strane message: ioctl[SIOCSIWENCODEEXT]: Invalid argument ioctl[SIOCSIWENCODEEXT]: Invalid argument And if I try to run dhcpcd then (which I manually installed, as it didn't come preinstalled with Ubuntu Server), it times out. Help on how to do it would be much appreciated. My wireless driver is iwl3945.

  Read the article

• How to set wifi driver settings to prefer 5 GHz channel above 2.4 GHz

  - by Wouter

  Currently I'm in a new building of my university. In this building my wifi often breaks down and then restores connection again. This is really irritating since it happens a lot. Now as a coincidence there were some tech guys running around here and where asking everyone if the wifi was doing fine. I told them that my wifi tears down all the time and then reconnects. They figured out that my wifi is switching all the time between the 2.4 GHz channel and 5 GHz channel. They asked me if I could acces the driver settings of my wireless card. Unfortunately I don't know how to do this is in either Linux or Windows. And unfortunately again they only knew the windows solution xD. So I hope somebody can tell me how I tell my wifi that it should stay on the 5 GHz network and not disconnect and switch to the 2.4 GHz channel?

  Read the article

< Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >