Search Results

Search found 2344 results on 94 pages for 'ethernet'.

Page 67/94 | < Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >

• Flow of packets in network

  - by user58859

  I can't visualize in my mind the network traffic flow. eg. If there are 15 pc's in a LAN When packet goes from router to local LAN, do it passes all the computers? Does it go to the ethernet card of every computer and those computers accept the packet based on their physical address? To which pc the packet will go first? To the nearest to the router? What happens if that first pc captures that packet(though it is not for it)? What happens when a pc broadcast a message? Do it have to generate 14 packets for all the pc's or only one packet reach to all pc's? If it is one packet and captured by first pc, how other pc's can get that? I can't imagine how this traffic is exactly flows? May be my analogy is completely wrong. Can anybody explain me this?

  Read the article

• How to set up Asus RT-N66U in bridge mode with wired connection to main router?

  - by Milligan

  I have a wired router (TP-Link RT-860) in the basement where the cable service comes in. Eight wired ethernet connections span two buildings. I currently have a Linksys wireless router set up in bridge mode, but its signal doesn't span the whole area. I have purchased an Asus RT-N66U to replace it, but I can't figure out how to set it up in bridge mode. Does anyone know if this is possible? Second question: Would there be any advantage in installing DD-WRT on the Asus?

  Read the article

• Virtualizing Firewalls/UTM

  - by TheD

  So Sophos UTM (Astaro Gateway UTM) can be virtualized in Hyper-V, VMWare, vSphere etc. Now I'm new to virtualization, so am wondering how the networking would be configured in this situation. Imagine the following (a very simple setup). A Zyxel router acting as the default gateway, standard ADSL line. This is connected directly via Ethernet to my VHost, Hyper-V in my case. Now I assume I need two virtual network adapters, one which is the "External" interface to the firewall, and the other being the "Internal" interface. But where does my switch go, since I have 5 machines (or X number of machines). Where is the switch connected, to the internal interface on the VHost? What default gateway do my clients use etc? How would the routing work if these two interfaces weren't bridged since they are virtual networks anyway. I'm a little confused! Any advice is much appreciated! Cheers

  Read the article

• DSL to web connectivity is often lost

  - by broiyan

  I am experiencing a frequent web connectivity problem via a DSL modem. The problem usually shows up as a reload later screen inside of Google Chrome, as illustrated. My DSL service was fine for the first 2 months, but in the most recent month this problem has been occurring. I have this problem several times a day. A few weeks ago, I used to power cycle (off then on) the DSL modem but this usually did not solve the problem. However, in recent days, the power cycle does seem to fix the problem. When the problem occurs, the modem lights do not look unusual. All the lights are green or flashing green. This problem happens regardless of whether I am using ethernet or WiFi for the last few meters between the DSL modem and the computer. What is the likely cause? How can I help the phone company solve this? Their staff are not very effective at troubleshooting this.

  Read the article

• windows hosted networok on windows 8

  - by tanmaysingh

  my sister is using Acer laptop, that has an intel WLAN card and supports windows hosted network(checked in command prompt).Am using the basic way using netsh wlan command also, then am using netsh start wlan command.The hosted network gets created and it could b seen in "Network and Sharing Center" as the . I also went to Device manager, selected WLan card, made sure"allow this device to wake computer from sleep" is selected. Now I went to the newly created , clicked properties, and under sharing enabled allow this to be shared(but I am not able to select The name of the wifi my sis wants to share (in this case her college wifi name, LEts say QP4,Ethernet and Local Area connection are the only two option that are coming). Also the SSID name is not being shown in her mobile nor when I click the tower icon at the tray area,Any suggestions on what might be going wrong?She is using windows 8. Should I look for updated drivers? Her laptop is only 6 months old, i don't think the drivers are outdated. Any advice shall be appreciated.

  Read the article

• RS-232 vs. RS-485

  - by user60524

  Doing a little research on the two to figure out which one may better suit my purposes (communications amongst different hardware). How do they fare against one another? Im far from being a specialist and have no idea where I would even start looking for data to compare and contrast. If possible can someone please answer the following questions in regards to each of these. Can they be networked amongst each other? Can they be easily networked over ethernet? What speeds do they transfer at? (Min, Max, Etc.) Reliability? Best framework to build on top of to support the above? Any standard communications programs? Debugging capability? Any help would be very much appreciated, thanks.

  Read the article

• Need to know who is hogging my bandwidth?

  - by Dev

  I have an ethernet connection to my iMac and with Internet sharing I am broadcasting the wireless network from my mac rather than using a wireless router. I use it to connect other devices wirelessly to the internet. But this makes all the traffic flow through my iMac. I wanted a way to analyze the traffic so that I know what connected devices are hogging the bandwidth at a given time and from which websites? I installed wireshark for mac and played around a little but it seems like an overkill when you first look at it. Can someone please help with few instructions to get what I need or any other way other than using wireshark? Thanks Dev.

  Read the article

• Ubuntu/Linux version recommendation for HP dv6 3122TX?

  - by sanjayav

  I purchased a HP dv6 3122TX recently and after installing Ubuntu 10.10 64 bit I ran into multiple issues like, The wireless driver is not supported by Uubntu. (1) [The driver is RaLink RT3090 ] The ethernet stopped working sometimes for no reason [The driver is Realtek RTL8111/8168B ] "Corrupted low memory at ..." issue which is described as a kernel bug in Ubuntu support forums. (It started to take me to a terminal instead of the GUI and couldn't start x server after that) As I'm not an expert Ubuntu user I got fed up of all these issue and got back to Windows 7. But I need an Ubuntu installation up and running for my development work. What are your suggestions about a reasonable Ubuntu version that I should try? Or a different Linux variation? Should I stick to a 32-bit version? It'd be great anyone can give some advice on this issue.

  Read the article

• OpenBSD Routing Problem

  - by Ozkan SENOVA

  I am running OpenBSD on a network appliance hardware. It has 5 NICs. I want to give different IP's in same subnet to 3 nics. Eg: em0: 192.168.1.5 em1: 192.168.1.90 em2: 192.168.1.56 I make the necessary configuration with ifconfig, all interfaces works as expected when all the ethernet ports are plugged in to switch. But there is something wrong in routing. If I connect to 192.16.1.5 via any service(http, smtp etc.), traffic goes over link#3. If I unpug the cable from em2 I can't reach any IP's binded on device. Is there any way to route traffic over different links in this IP configuration?

  Read the article

• Centos 6 - How to upgrade module located inside initramfs?

  - by anonymous-one

  We have recently upgraded our e1000e (intel ethernet) module on one of our centos 6.0 boxes. Even tho the module compile and installed fine, the old version is still being used. We have tracked this down to the fact that the e1000e.ko module is located inside the initamfs file for the booting kernel and thus, even tho the module located in /lib/modules/.... was being updated, the old one is still being loaded from inside the initramfs file. After some research, we have found that creating a new initamfs file in centos should be as simple as: /sbin/dracut <initramfs> <kernel-version> Can someone confirm that this is a safe way to basically recreate the initamfs file? This is a non-locally hosted (1000's of km away...) box, and getting support to resolve this if a reboot is unsuccessful will lead to quite a bit of down time. Thanks.

  Read the article

• Time randomly changing itself, internet randomly dying

  - by Vee

  Operating System MS Windows 8 Enterprise 64-bit CPU Intel Core i7 2700K @ 3.50GHz 45 °C Sandy Bridge 32nm Technology RAM 8,00 GB Dual-Channel DDR3 @ 800MHz (8-8-8-24) Motherboard ASRock Z77 Extreme4-M (CPUSocket) 40 °C Graphics SMXL2270HD (1920x1080@60Hz) M2094D-PZ (1680x1050@60Hz) 896MB GeForce GTX 275 (CardExpert Technology) 57 °C Hard Drives 466GB FUJITSU MAXTOR STM3500320AS (SATA) 39 °C Optical Drives ASUS DRW-2014L1T Audio High Definition Audio Device Hello everyone, I installed Windows 8 RTM a few weeks ago. It's not my first time installing it, but it's the first time having two annoying problems: 1) Randomly, the system clock changes time all by itself - to fix it I have to open the time window and sync it with the internet. 2) Randomly, internet connection stops working - to fix I have to run troubleshooting. Windows will find a problem with IP on the "Ethernet" connection and fix it. 3) In rare occasions, my PC freezes and I need to restart it (a BSOD once happened, but after that only freezes) How can I permanently solve these problems? This is what I've already tried: Reset Virus scan Stop/reset the Windows Time service Disable/re-enable Windows Time automatic internet sync Change time from BIOS Change motherboard battery

  Read the article

• Streaming audio to headless linux box

  - by Ralph

  I have a dual boot (Win 7 + Ubuntu) PC connected via wifi with my music collection on a local HDD. I usually use Rhythmbox on Ubuntu or Winamp on Windows to listen to my music but I'll change if I have to. I also have a Raspberry Pi (low power PC running Debian) in the living room that is usually headless and connected via ethernet. The Raspberry Pi is also connected to my living room speakers via an amp. I would like to be able to stream music from my PC over the network to the linux raspberry pi. What software can I use to do this? Some sort of audio client\server?

  Read the article

• Wireless is connected but no internet when PC Turns on

  - by mhesabi

  I have a PC that is connected to ADSL Modem router (linksys WAG54g2) directly via Ethernet cable And a laptop and also other devices such as another laptops and smarth phones. However when I turn On the PC or turn it off, some strange problem happens. My wireless network seems connected on laptop but there is no internet activity and can't open a webpage until I turn router off and on again manually. (other devices including the PC itself can't use the internet either) My router configured this way: Encapsulation: RFC 2516 PPPoE Multiplexing: LLC DHCP Server: Enabled and network sharing center IPv4 configuration is obtain IP address automatically How Can I fix this issue?

  Read the article

• What is the pixel clock setting on my monitor actually doing?

  - by codecowboy

  I am experiencing display interference on a dell 24" flat panel monitor.I find that if I adjust the pixel clock settings up or down in the monitor's on-screen menus, the interference goes away for a while. The monitor is attached to a Macbook Pro using a mini display to VGA adapter. I have found that in a different house, I get the interference problem less so it might be related to electricity supply or possibly even ethernet powerline (total guess). What does the pixel clock setting actually do and does this behaviour point to a likely cause of the interference?

  Read the article

• What are good and bad jitter times for a LAN

  - by garyb32234234

  Ive just ran jperf (frontend to iperf) on our network between 2 workstations, its recorded jitter between 0.033ms and 0.048ms. Is this good or bad? Are there more variables that i would need to consider to make the decision? EDIT: TCP/IP Ethernet LAN 43 PCs 1 server, 100Mbits main switch, various small 8 port switches, test was done using UDP, Its a Windows Domain. I want to instal a few voip softphones on the workstations, see how many i can use that reliably work, im testing a few different workstations around the network to see where the best quality network paths are. Will also change some equipment if i identify bad connections.

  Read the article

• Impossible do find motherboard drivers to Dell Dimension 3000

  - by Masziej

  Hello, I recently formatet and reinstalled XP on my girlfriends computer. Ive had this computer since 2001, never formatet it, until now =) Anyway the problem is that i cant find any drivers for the motherboard (integrated audio, video and ethernet). as i said its an old ass Dell. Cant remember if I got any cds along with it. Even if i did theyre gone a long time ago. So, I ran CPUZ and got this: --Motherboard-- Dell Computer Corp. Model 0K8980 And started googling. But didnt find any drivers. Still cant So im asking for a little help here. I really need to get the computer going before she wants a new one :D And yes i have looked on dells homesite, but they dont seem to wanna host drivers for their old stuff

  Read the article

• Setting up a linux switch

  - by Shahmir Javaid

  I have a C++ Program to sniff each and every packet that crosses my linux box. However i need to now get my linux box to listen to every traffic in my network. I could buy a managed switch and set up port spanning, but i aint paying 200+ £'s for a switch and plus gives me a chance to learn. My Network +---------Computer A | Internet-----Router------Switch-------------+---------Linux Box | +---------Computer B Proposed Network +---------Computer A | Internet-----Router------Linux Box--------Switch eth0^ ^eth1 | +---------Computer B How would i setup this in linux. Do i just configure both the ethernet on different IP Address on the same network. Or am i completelly on the wrong track My System Fedora 13. Thanks

  Read the article

• XenServer 5.6.1-fp1. Can't get network working

  - by casey_miller

  I have a PC where XenServer 5.6.1 fp-1 has been successfully installed. I've manually set the network settings: 192.168.1.50 255.255.255.0 192.168.1.1 but it's set to xenbr0 iface. While eth0 is empty. When I click on "Configure Management Inteface" it shows that eth0 is connected. But when I ping a default gateway (which is 100% should be accessible) it fails. I used to another shell (Alt+F3) and logged as root. I also failed to ping. with both: ping -I eth0 192.168.1.1 and ping -I xenbr0 192.168.1.1 Be assured that: Cable works Ethernet adapter is 100% functional (prev OS was Ubuntu it was working) There is no firewall rule to deny anything. (everything is allowed) So the question is: What is a problem???

  Read the article

• Windows 7 Natively on Mac OS X Bootcamp, Airport Wifi Unable To Connect

  - by Goober

  I am using a brand new MacBook Pro. I am running a copy of Windows 7 natively via bootcamp (No use of Virtual Machine Software at all). However the only way I can get Windows to connect to the internet is via ethernet, as opposed to the Macs Airport card picking up the wireless. It just refuses to connect, and gives me a limited access status. Any ideas!? I've run Windows XP natively via bootcamp and I had a few issues with the network constantly dropping out, however I blamed that on the drivers and the general shiteness of XP.... Help greatly appreciated.

  Read the article

• Wireless only connects to Google

  - by dmanxiii

  I am using a netgear wireless router to connect to create a wireless network. When connected to the router via an Ethernet cable everything works correctly. When connecting to the router via wireless only Google can be accessed. I've done searches via Google using random words to make sure that it is not a cached page, and these all work. However, trying to connect to any non Google domain the page fails to load. I've accessed the connection with two different laptops, both are running Windows Vista. The network connection is strong on both, but the issue persists for both. Edit: I have configured the wireless networks name and password, and connect to that using the credentials I have defined. I am sure I am not connecting to a neighbors wireless network. Edit2: Typing in the direct IP address for CNN.com ( http://157.166.255.19 ) would not resolve.

  Read the article

• Motherboard: Intel S5520HCR s1366 SSI EEB

  - by Crazy_Bash

  I'm building a storage server for online video streaming. I thought about adding two SSD drive for a OS. other 15*(12 SATA & 3 SSD) drives i want to build with aufs XFS and ethernet 4GB/sec network. But I'm confused a little. S5520HCR board supports 6, SATA/300, RAID: 0, 1, 10, Intel ICH10R. Does it mean i can use SATAIII HDD? I'm planing on buying SEAGATE SV35 Series (3.5, 3??, 64??, SATA III-600). also my Chassis supports up-to 16 sata and the motherboard only 6 what kind of sata controller should i use? What's better in terms of performance 1366 or 2011 socket? My server so far: AIC RSC-3EG-80R-SA1S-2 3U Motherboard: Intel S5520HCR s1366 SSI EEB Kingston DDR3 8192Mb PC3-10600 1333MHz (KVR1333D3N9/8G) Seagate 3000GB 64MB 3.5" 7200rpm SATAIII (ST3000DM001) Kingston 480GB SSD 2.5" SATAIII Intel E1G44HTBLK Intel Xeon E5606 2133MHz/L3-8192Kb/QPI s1366 tray SERVER ACC CARD SAS PCIE 16P HBA 9201-16I LSI00244 SGL LSI

  Read the article

• Why are my downloads up to ~1500KByte/sec only, when the ADSL connection locks at 13611Kbit/s?

  - by leladax

  No uploading is going on other than the overhead of downloading which appears to be not high for the abilities of the connection: Only about 30-40KByte/s when the router locks at 1012Kb/s and other direct uploads or uploading overheads can reach more than 100KByte/sec so I don't think it's a congestion at uploading that is doing it. Is there something I miss? Because I assume 13611Kbit/s should be ~1701Kbyte/sec. Is it an overheard at the ADSL level I don't understand? Could it be the ISP doing it? If it's active throttling it can't be on single connections since 2 high speed connections still go up to ~1500KByte/sec. It's not an example on torrents or other complex situations. The tests were on Ethernet, but I doubt the results would be different on wireless. I wonder if the settings of those connections at my end could be doing it, e.g. MTU settings, though I haven't touched the defaults of a common Realtek NIC.

  Read the article

• Extend university wifi network [migrated]

  - by asfasdoiuh ouhouhouh

  i live in a university campus and i can get wifi signal on the outside of my window but not in the house. The solution i use at the moment is a usb wifi dongle outside connected to my laptop but the lack of an internal antenna make the connection quite unreliable at times. So i was trying to find another solution to improve the reception of my network. One idea is to setup a router on the outside (in a place with stronger signal) and redirect the connection inside the house with an ethernet cable but the problem is that our Uni Wifi is managed by a capitve portal (BlueSocket with DNS redirection to login page) and the authentication has to happen on the mac address that connect to the net (so the client appliance in this case). If I use a router with Mac-Clone capability i will be able to be redirected trough the captive portal on my laptop computer and login from there or i need to setup my router to fill in the login page by itself? There are other hardware/software solutions i can use to get what i want? Thank you all

  Read the article

• Setting up Multiple Routers (as Hardware Firewalls) behind a Home Router

  - by Synetech

  I’ve currently got one computer behind a router with built-in firewall functionality, connected to a home cable-modem that has a single Ethernet port and one IP. I’m going to have to set up another computer for the rest of the family to use which of course will need to be connected to the Internet, probably wirelessly since the modem is in my room and the new system would not be. What I would like to do is to get two more small routers with firewall capability and connect each computer to a router, which would in turn connect to the main router which connects to the cable-modem. That way, both systems have a hardware firewall protecting them (particularly the wireless system) and the burden of blocking would be reduced on both the computer CPUs and the main router because the secondary routers would handle some of the workload. I’m trying to find out about the complexities inherent in this design and how I could set it up to work, specifically the IP handling and NAT aspect. Thanks a lot.

  Read the article

• Does a single LACP channel over multiple switches increase redundancy?

  - by Sirch

  I am curious for opinions, findings, or evidence that having multiple interfaces bonded using LACP to ports in multiple switches can increase redundancy. Previously bonded interfaces have always been to a single switch, with a redundant channel to another port. Without getting into vendor specifics, my thought is that as this is a single LACP, the likelihood that an event or change could lead to a wide service outage. Without having the spare equipment or time to test this single channel over diverse switches, could anyone with a greater networking knowledge than myself, tell me if there a network side event that would bring down the network connectivity to a server that had created a bonded interface to two ports on separate switches? Does the use of bonded ethernet channels across multiple switches (that we are advised that we can use) from the server, provide both improved throughput (unquestionably), and improved redundancy (uncertain). Could/would network events such as switch failure, port migration, patching, recovery, etc, cause the channel for both server network interfaces to be unavailable? Thanks in advance.

  Read the article

< Previous Page | 63 64 65 66 67 68 69 70 71 72 73 74  | Next Page >