Search Results

Search found 2066 results on 83 pages for 'cable'.

Page 69/83 | < Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >

• Using native resolution on external display results in stretched, out of bounds image

  - by Roni Yaniv

  I have an HP min 311 netbook with Windows XP, which I've connected to a Samsung SyncMaster 2043BW display via the supplied analog cable. The external display's native res is 1680x1050, which the netbook's ION GPU supports. I've configured the external display as the single display (no cloning or any such fancy stuff). However, once I set the native res, the image just stretches out. It looks squashed, and it goes outside the monitor's edges. In contrast, lower resolutions manage to stay within the monitor's display edges, though obviously they are skewed in some way (vertically or horizontally). BTW, the only res which seems to be displayed relatively clearly (it's the least blurry) is 1280x720. I tried looking all over the web for an explanation/advice but could not find any. I already played with the settings on the external display itself several times. So either it's not that, or I missed something. Has someone run into this issue? I need help.

  Read the article

• Cooling for a small server room

  - by John Zwinck

  I have a server room about 12 feet square with an unfinished ceiling (exposed ducts and wiring). It houses a few servers (about ten, 1U and 2U) and some networking gear (four 1U switches, three routers, three modems, two cable boxes). With the door closed, it runs around 80 degrees Fahrenheit with half the servers turned on. When I turned on all the servers it reached 86 before I chickened out and propped the door open. The room is adjacent to air-conditioned office space, but does not itself have dedicated air conditioning. The ventilation for this room seems to be limited to one duct coming in at ceiling level, with a powered fan to draw air in, and one duct at ceiling level to allow air to flow out (it seems like it may just go into the drop ceiling cavity in the adjacent room). The adjacent office space stays fairly cool, but I'd prefer not to leave the door propped open all the time. There is both 110v and 208v service in the room, and plenty of power available. But there are no windows, and no floor drains (in a pinch we might be able to run a condensation hose through a small hole we'd drill in the wall to a nearby sink area, but only if absolutely necessary). I've considered portable A/C units, but I'm not sure on sizing and a lot less sure how we would run the exhaust hose(s). I suppose we could point one at the existing room exhaust duct (air return), but substantially modifying the duct is probably a no-no. I've also considered installing a fan box in the door of the room, but I'm concerned that this will only drop the temperature a little. Even right now, with all the equipment on, the room is at 83 degrees with the door open. And the main building A/C turns off daily at 6 PM to conserve energy, so the adjacent room temperature rises at night. How would you cool this room? Let's say the goal is to bring the temperature with everything running from a steady state of around 90 degrees down to 75 (equivalently, to offset the heat produced by ten 1U servers).

  Read the article

• Instant connection to wireless network but delayed internet access on Mediacom with Windows 7

  - by David

  I have Mediacom cable internet and their provided modem/wireless router a Cisco DPC3825. Each of the laptops experiencing the trouble have Windows 7 64-bit. When connecting to the wireless network each computer will take a second or two to connect and then toggle from "no internet access" to "internet access" however, no websites are accessible for about five minutes after connecting. After that, there aren't any problems. It happens on all 3 of the laptops I have available and none of them have problems on any other network. It seems like my phone doesn't have the delay issue when it connects. I've power cycled the modem/router along with a DNS flush. I have some of the DNS servers manually set to Google DNS addresses and one just default. I've contacted and had Mediacom support try all its tricks. They changed the SSID and password along with resetting the thing remotely a handful of times. It was installed just this month and seemed to pass the tech's checks upon installation. Nothing in the settings has been changed, but it's been exhibiting this problem from the get go. This guy seems to be having the same problem, but no solution was posted. http://www.dslreports.com/forum/r27372861-IA-Connection-to-Mediacom-wireless-Modem-no-internet- Help greatly appreciated.

  Read the article

• Laptop will not boot

  - by WillumMaguire

  This is a dell studio 1558 laptop. Now, something is wrong with the charger that it won't charge the laptop, but the laptop can turn on and operate properly as long as it is attached. It has been like this for a while, but it's not the problem. My problem is that as of yesterday, It takes several minutes to get past the "dell" startup logo (where is says "f2 setup" and "f12 boot options"). After it gets past, it beeps as normal to tell me about the charger and gives me the f2/f12 options and f1 to continue as normal. I can press f12 to get into boot options and load into my live USB BackTrack 5 ISO, but after "startx" it just stays at a black screen. I can also access BIOS setup, but see nothing that would help the problem. When I boot to the HDD, it gives me this Intel UNDI, PXE-2.1 (build 083) Realktek PCIe GBE Family Controller Series V.2.29 (06/30/09) PXE-E61: Media test failure, check cable PXE-M0F: Exiting PXE ROM Operating System not found Also, pressing f8 gives me the same results as booting as normal. It is running Windows 7 Ultimate, dual-core Intel i3 @ 2.27ghz and 4gb RAM. I think there is an issue with the HDD, as the "Operating System not found" would lead me to believe. Is this a fixable problem?

  Read the article

• Which internet scenario would be better?

  - by JL

  I currently have an 8mbps (down) / 512kbps (up) telephone ADSL solution. I must say the reliability is excellent, and up until now its been the fastest connection I could get because I don't live in a cable zone. The real speed of my connection is around 7mbps, but sometimes I manage to get the full 8mbps. I use my connection for work, so it needs to be at least 99% reliable. Recently I was told by a guy who lives up the road that he has a wireless connection with an external antenna and his speeds are 20mbps / 512kbps - he's also paying about 1/2 of what I pay for my wired telephone connection. My question is, is wireless internet good enough for a power user who uses his connection for work 8 hours a day, including VPNing into servers remotely. Besides this I also enjoy playing the odd network game, not a WoW freak, but sometimes I do pick up the odd MMORPG and at times do indulge in some semi heavy gaming sprees. Will this wireless latency drive me crazy and seem slow in comparison? Will it be reliable enough, I also live in an area that snows heavily in winter. I guess its a question of - should I go wireless or not. I've only had 1 wireless connection before and that was years ago using iBurst technology and I remember it was terrible for VPN, but I guess the technology might have been improved since then? What do you guys think?

  Read the article

• Streaming to PS3 with NAS and built-in dlna server?

  - by philt

  With consumer-grade hardware, is it possible to successfully stream 1080p mp4 videos to a PS3? I have a linksys router that can only do 10/100. The PS3 is wired to it with cat5e cable, and the PS3 itself supports gigabit ethernet. I would upgrade the router and get one that supports gigabit ethernet if it could handle streaming like this. It currently does work with minor jerkiness streaming from my mac to the PS3, but fast-forward/reverse and "goto" (equivalent of scene selection) take forever and/or fail completely. And streaming from my mac of course requires the mac to be on at all times. When I put the movies on an external USB drive and connect to the PS3 directly, it performs flawlessly. Fast forward and everything works great. So I was thinking about getting a NAS, but I don't know if any inexpensive NAS (i.e. Buffalo Linkstation Live, WD My Book World Edition, D-Link DNS-321, etc.) can actually deliver the performance necessary to do this, even with gigabit ethernet?

  Read the article

• Why is the link between my switch and my router always negotiating half-duplex mode?

  - by Massimo

  I have a Cisco 2950 switch which has one of its ports connected to an Internet router provided by my ISP; I have no access to the router configuration, but I manage the switch. If I leave all switch ports with their default setup (auto-negotiation of speed and duplex mode), this link always connects at 100 MBit/s, but in half-duplex mode. I've tried replacing the cable, and also moving the link to another switch port: the result is always the same. A different device connected to the same port (or to any switch port, really) shows no problem at all. It could be guesed that someone configured the router to only connect in half-duplex mode... BUT, here's the catch: if I manually force the switch port to full-duplex mode (duplex full in the interface configuration), the link goes up, stays up and is completely stable. So: The connection is not forced to half-duplex mode by the router, otherwise it would not connect at all if I force the switch end to full-duplex. There is no actual link problem, otherwise the full-duplex connection would not go up or would at least show some errors. But if I leave the port free to auto-negotiate, it always connects in half-duplex mode. Why?

  Read the article

• VoIP setup for one external PSTN line

  - by Jcl

  I'm completely new to VoIP and the likes, and I'm trying to find information about what could be the best setup for this. I need 4 (maybe more in the future, but maximum 5 or 6) wireless extensions, connected to 1 PSTN line, and maybe 2 in the future. I've been trying to gather information about the gear needed but everything I find seems too much over-the-top (and extremely expensive). The main problem is that the physical place we are on doesn't have possibilities of having a decent internet connection, so using a external VoIP "virtual PBX" is not an option. Thing is, even if small, phone is critical to this organization. I currently have an analog DECT/GAP PBX which does what I need, however the PBX is very bad and the call quality is horrible, and that's why I want to change it. The requirements would be: 4 wireless terminals (routing cable is not an option), all of them ringing on incoming PSTN calls. Ability to do internal calls (4 separate offices) and ability to pass calls between terminals. The 4 terminals should be able to access the external PSTN line without dialing any special codes. Very important: terminals should be able to issue commands on the PSTN line to the external operator in the form *nn*nnnnnnnn# . Don't know wether this could face to be a problem, but I've had problems with analog PBX which would take any * as a PBX command and wouldn't allow terminals to send it to the external lines. Not so important, but would be nice to have: call waiting music Could anyone recommend such a setup? I need to be able to do this on a EXTREMELY LIMITED budget (that is: I don't have a limit, but all should get as much to zero as possible). I have enough spare powerful computers and a 300mbps wireless network which works just fine, so that's not to include in the budget. Don't really know if this is the best place to ask, but it's the most StackExchange-related site I've found to this subject.

  Read the article

• ProCurve 1800 switch issue

  - by user98651

  I recently deployed ProCurve 1800-24G switches in place of some older ProCurve 2424M switches in my network. However, I'm having a serious problem with the switch connected to the router. It seems, every night when our Windows 2008 R2 server (off site) runs a backup to a iSCSI target (on site) [facilitated through a PPTP tunnel] the LAN loses connectivity with the router. To clarify, there is only one router which is connected to the switch affected by this problem. The only way to resolve the issue is to either reboot the router or pull the ethernet cable that goes to the router and plug it back in. During the outage, clients cannot receive DHCP requests, DNS requests, ping, or do anything else with the router in this state. Now, neither the switch or router are configured extensively and the issue only seems to have surfaced with the new switch in place. I have tried a number of things including replacing cables, rebooting and checking the switch configuration (it is literally as basic as you can get at this point-- flat LAN, no trunking). Interestingly, the router shows (accessed externally) no changes in configuration or status during this state but similarly cannot ping or access other hosts on the network. This issue occurs in different stages of backup (ie, different amounts transferred). I've also dumped packets from the switch into WireShark but cannot seem to find any anomaly yet (I'm looking at packets around the time the issue appeared and at the time when I reset the NIC). Any suggestions for what to look for? Ideas on what could be causing this? I'm seeing some transmit/receive errors on the NIC from both the router and switch side but nothing serious when compared to the total packet counts. I'm seriously doubting hardware at this point, as I have tried another switch, different cables, and a different NIC on the router.

  Read the article

• OpenSSL: how to setup an OCSP server for checking third-party certificates?

  - by StackedCrooked

  I am testing the Certificate Revocation functionality of a CMTS device. This requires me to setup a OCSP responder. Since it will only be used for testing I assume that the minimal implementation provided by OpenSSL should suffice. I have extracted the a certificate from a cable modem, copied it to my PC and converted it to the PEM format. Now I want to register it in the OpenSSL OCSP database and start a server. I have completed all these steps, but when I do a client request my server invariably responds with "unknown". It seems to be completely unaware of my certificate's existence. I would greatly appreciate if anyone would be willing to have a look at my code. For your convenience, I have created a single script consisting of a sequential list of all used commands, from setting up the CA until starting the server: http://code.google.com/p/stacked-crooked/source/browse/trunk/Misc/OpenSSL/AllCommands.sh You can also find the custom config file and the certificate that I am testing with: http://code.google.com/p/stacked-crooked/source/browse/trunk/Misc/OpenSSL/ Any help would be greatly appreciated.

  Read the article

• OpenSSL: how to setup an OCSP server for checking third-party certificates?

  - by StackedCrooked

  I am testing the Certificate Revocation functionality of a CMTS device. This requires me to setup a OCSP responder. Since it will only be used for testing I assume that the minimal implementation provided by OpenSSL should suffice. I have extracted the a certificate from a cable modem, copied it to my PC and converted it to the PEM format. Now I want to register it in the OpenSSL OCSP database and start a server. I have completed all these steps, but when I do a client request my server invariably responds with "unknown". It seems to be completely unaware of my certificate's existence. I would greatly appreciate if anyone would be willing to have a look at my code. For your convenience, I have created a single script consisting of a sequential list of all used commands, from setting up the CA until starting the server: http://code.google.com/p/stacked-crooked/source/browse/trunk/Misc/OpenSSL/AllCommands.sh You can also find the custom config file and the certificate that I am testing with: http://code.google.com/p/stacked-crooked/source/browse/trunk/Misc/OpenSSL/ Any help would be greatly appreciated.

  Read the article

• How can I get my SATA DVDs working again?

  - by user269051

  My hard drive crashed (WinXPpro), so I took a C drive from a broken PC. The new C drive is Win7pro. Motherboard is MSI K8N Neo4 Platinum, with 4 hard drives installed on SATA 1-4 (nForce4 Ultra); the two DVD drives are loaded on SATA 7-8 (Silicon Image SATARAID5). I've tweaked BIOS settings every which way. The closest thing to success was when each DVD had both a CD and a DVD icon, and blinked green. No CD or DVD could be read in either drive. I assume that the problem resulted from the fact that my new C drive does not have the RAID drivers? I've tried loading from the floppy (doesn't work). I can't boot off the DVD/CD, and switching the DVD's SATA cable to the SATA 3 slot (and pulling one of the hard discs) didn't work. I'd like to be able to use the other two available SATA slots for a mirrored RAID drive, and get my DVDs working again. Any suggestions?

  Read the article

• Media Center - TV constantly pauses 1/2 second then plays 1 second

  - by Bob

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. I know the problem is Media Center because I can use Pinnacle's TVCenterPro and there is no skipping/pausing. I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing it okay before I tried to run setup. (I ran setup to try to do recording with Media Center.) Pinnacle PCTV 800i HD PCI card, ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Why my 2nd ip from traceroute is not answering the ping anymore?

  - by Pedro77

  My Internet is really laggy today, I did a tracerout and I realize that I'm having no answer from an ip at the beginning of the traceroute. see: Tracing route to 12.129.202.154 over a maximum of 30 hops 1 <1 ms <1 ms <1 ms 192.168.0.1 2 * * * Request timed out. 3 8 ms 8 ms 8 ms bd044008.virtua.com.br [189.4.64.8] 4 9 ms 8 ms 8 ms bd044009.virtua.com.br [189.4.64.9] 5 26 ms 26 ms 24 ms embratel-T0-1-5-0-tacc01.cas.embratel.net.br [200.174.243.21] 6 360 ms 15 ms 12 ms ebt-T0-15-0-12-tcore01.ctamc.embratel.net.br [200.244.140.218] 7 330 ms 349 ms 261 ms ebt-Bundle-POS11942-intl04.mianap.embratel.net.br [200.230.220.10] 8 139 ms 141 ms 139 ms sl-st30-mia-.sprintlink.net [144.223.64.221] Connection diagram: PC - Router configured as access point - Router (192.168.0.1) - Cable modem (192.168.100.1). Well, I think it is odd that the 2nd ip is not returning the ping. I looked some old tracerout logs to see what was the 2nd ip. The ip was: 10.19.0.1 So, what this 2nd ip stand for? How can I find why it is not answering the ping? I don't understand it, if does not answer the ping, how can the packets continue (yeah newbie question)? edit: well, because the hope 3 have a ping of 8 ms the hop 2 request time out should really not be a problem. But it is still odd that the 2nd hop stopped to answer ping request. So my doubts are: 1. Were the ip 10.19.0.1 is from? 2. Why it stopped to answer ping requests? 3. How can hop 7 be smaller than 6 and 8 smaller than 7 and 6!?? Shouldn't the pings be higher for each hop? Like: hop 3 time should be the sum of the hops before it plus its own time (hop 3 = 1+2+3) ??

  Read the article

• Java Swing over Remote Desktop - Strange, weird GUI squashing

  - by ADTC

  I thought this question fits SuperUser more than StackOverflow because it's not about actual Java programming, though programmers might be more likely to encounter the problem. Anyway, let me start of with some stats before I ask the actual question: Laptop: Windows 7 x32 Screen resolution 1024 x 768; Nvidia GeForce Go 6200 Connected to desktop via ad-hoc wireless network Access internet via desktop Desktop: Windows 7 x64 Screen resolution 1920 x 1080 Connected to laptop via ad-hoc wireless network Access internet via cable modem I'm connecting to my laptop via Remote Desktop from my desktop to take advantage of the large screen. I'm doing programming on my laptop (for portability reasons). Everything else runs smooth and fast over Remote Desktop as both computers are connected directly over the ad-hoc wireless. The only problem is this: Java Swing apps don't display the GUI properly. I acquired a Java Swing application and I'm debugging it in Eclipse. Here's what I got when I ran the app: Apparently there doesn't seem to be anything wrong with the GUI application I'm debugging, because the Java Control Panel exhibits the same problem. I've searched high and low in Google about this; the closest I came to a solution is this. But sadly, the use of -Dsun.java2d.nodraw=true has no effect at all. This only happens over Remote Desktop. I have tried locally and the GUI apps display properly. This isn't a dealbreaker for me as I can stop using Remote Desktop when developing Java Swing apps. However, I would like to know if anyone has encountered this and found any solution. PS: All software involved (Eclipse, Java JRE, etc.) are latest versions.

  Read the article

• Portable, battery-powered, wireless access point, ethernet adapter

  - by Jed

  I am in need of an adapter that will convert an ethernet port into a wireless access point. I have found a handful of devices, but I'm unable to find a device that is battery powered. Does a self-powered wireless access point even exist? The particular scenario that I will be using the device for is not your typical computer/PC scenario. For the curious, here's a bit of background on the problem I'm trying to solve: I make devices (controllers) that monitor water systems. Our controllers have a Webserver that serves out web pages so that users can configure the controller's settings. Typically, the user will use a cross-over cable to connect directly to the controller's ethernet port with their laptop to gain access to the controller's web pages. Now that tablets (devices that don't have an ethernet port - iPad, for example) are becoming more common, I need to find a device that will convert the controller's ethernet port into a wireless access point so that the user can connect to the controller's web pages via Wi-Fi or Bluetooth. It's worth noting that this wireless device that I'm looking for will NOT be permanently installed on the controller. It will be a portable device that the user will use on any of his controllers when he needs to make a connection to the controller. If you know of a device that will solve the scenario that I mention above, please share your info.

  Read the article

• Proper Network Infastructure Setup DMZ, VPN, Routing Hardware Question

  - by NickToyota

  Greetings Server Fault Universe, So here's a quick background. Two weeks ago I started a new position as the systems administrator for an expanding health services company of just over 100 persons. The individual I was replacing left the company with little to no notice. Basically, I have inherited a network of one main HQ (where I am situated) which has existed for over 10 years, with five smaller offices (less than 20 persons). I am trying to make sense of the current setup. The network at the HQ includes: Linksys RV082 Router providing internet access for employees and site to site VPN connecting the smaller offices (using an RV042 each). We have both cable and dsl lines connected to balance traffic (however this does not work at all and is not my main concern right now). Cisco Ironport appliance. This is the main gateway for our incoming and outgoing emails. This also has an external IP and internal IP. Lotus domino in and out email servers connected to the mentioned Cisco gateway. These also have an external IP and internal IP. Two windows 2003 and 2008 boxes running as domain controllers with DNS of course. These also have both an external IP and internal IP. Website and web mail servers also on both external and internal IPs. I am still confused as why there are so many servers connected directly to the internet. I am seriously looking to redesign this setup with proper security practices in mind (my highest concern) and am in need of a proper firewall setup for the external/internal servers along with a VPN solution about 50 employees. Budget is not a concern as I have been given some flexibility to purchase necessary solutions. I have been told Cisco ASA appliance may help. Does anyone out in the Server Fault Universe have some recommendations? Thank you all in advance.

  Read the article

• Backup data rate on Raspberry Pi maxing out at 5 Mb/s. Why?

  - by bastibe

  I set up my Raspberry Pi as a Time Machine, as documented here. At the moment, the Raspberry Pi is connected to my MacBook Pro using a direct Ethernet cable. Also, an external hard drive (laptop drive) is connected to the Raspberry Pi using the USB port. However, backups are pretty slow. Activity Monitor claims that the Network is transferring a very steady 5 Mb/s, where my Time Capsule is transferring up to 8 Mb/s with a lot of fluctuation. The Raspberry Pi self-reports (top) that its CPU is only half-used, with about equal parts afpd, usb-storage and jbd2/sda1-8. Thus, I think that the processing power of the Raspberry Pi does not seem to be the problem here. To me, this looks like there is some kind of bottleneck that maxes out at 5 Mb/s thus potentially having my backups run at less than their potential speed. To the best of my knowledge, this might be the afp-daemon, the usb-bus or the external hard drive. So, my question is, how could I identify the true culprit and what can I do about it?

  Read the article

• Why am I seeing MailSlot Browse messages on unrouted ports of my Linux box?

  - by nmichaels

  I have a Linux box (Debian squeeze) with several NICs. The ones of interest are: eth3 - my main link to the network (dhcp on 10.20.30.0/24) eth0 - the first connection to my test network (static: 192.168.1.2) eth4 - the second connection to my test network (static: 192.168.1.1) My routing table looks like this: $ sudo route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.20.30.0 * 255.255.255.0 U 0 0 0 eth3 default 10.20.30.254 0.0.0.0 UG 0 0 0 eth3 I have the 2 test net ports connected to each other with a crossover cable and an instance of wireshark running on each port. Every once in a while, I'll see a packet like the following show up. Who could be doing this, and how do I convince them to stop? I do have Samba running on the machine (for a cifs mount) but don't see why it would be sending packets out to unrouted ports. I had a Windows VM running in VMWare Client and thought that might be causing it, but it still happens without it. What I want is totally silent interfaces so I can run some tests with Scapy over them.

  Read the article

• Networking - intermittent, slow speeds

  - by jack

  Hi all I'm a novice when it comes to networking. I live in a large two storey building that used to be a school and we have an internet connection with BT (british telecoms provider), the connection speed is 12Mb.. Basically our connection is slow and very intermittent and I was wondering if anybody here could provide some help or ideas. There are about 11 people in the building who could be online at any time. We have a router on the ground floor which is bog standard supplied by BT. To provide Broadband access to the 1st and 2nd floors, we used an old switch that the school left, we have a cable running from the router on the first floor to the switch which connects to a wireless router which is configured as a bridge on the 2nd floor supplying broadband access to the 1st and 2nd floors. Additionally we have 3 computers that are connected via the switch through the ethernet sockets left by the school on the ground floor. The router we use on the 2nd floor came in a pack of 2 and cost about £15 (bought by another person). Sometimes the connection is perfectly fine, i.e. early hours of the morning or when everybody is out, we have rang BT who say that the connection cannot cope with the numbers of people online, plus I'm not sure whether each person is streaming etc. Can anybody offer any advice?

  Read the article

• Port Forwarding(?) TD-W8961nd

  - by rich

  I have a bit of a weird internet setup. I am connected via a decent WiFi connection (from work) which I pick up using a Buffalo Airstation Wireless-G box. This simply picks up the signal and gives me 4 ethernet ports to connect to. That's all fine and works as it should. I also have a TP LINK TD-W8961nd router which used to be connected to the Airstation via an ethernet cable so I could essentially have WiFi access in my house. To cut a long story short I can't remember how the hell I got it to work and I can't find the notes I scribbled down on how to do it. I'm pretty sure I need to tell the router what ip to pick up the internet connection from and have the local wifi as a seperate network. How the hell I do that I have no idea right now. Can anyone give me some advice on this? If you need more information ask and I will be able to do so. Cheers in advance. edit I'm in work at the moment so I can't give 100% details but I will be able to later on.

  Read the article

• How to get gigabit network speeds on Windows XP?

  - by JB

  We've just installed gigabit switches at work, and things on the Linux side are going well. Our linux boxes, which use a Intel Corporation 82566DM-2 Gigabit nic (according to lspci), consistently get over 900 mbits/sec: iperf -c ipserver ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 16.0 KByte (default) ------------------------------------------------------------ [ 3] local 192.168.40.9 port 39823 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 1.08 GBytes 929 Mbits/sec We have a bunch of Windows XP 64-bit machines that use Broadcom NetXtreme 57xx cards. I spent around a day trying to get equivalent speeds on them, but couldn't get above 200 Mbits/sec. I noticed the Windows iperf tests said that the TCP window size was 8 Kb by default (as opposed to 16 Kb on Linux, so I modified my test to reflect that. Still no love. I went to Broadcom's site, downloaded the latest drivers for the card and installed. Still no love. However, finally, I tried a 64 Kb window size with the new drivers, and finally an improvement! $ iperf -c ipserver -w64k ------------------------------------------------------------ Client connecting to ipserver, TCP port 5001 TCP window size: 64.0 KByte ------------------------------------------------------------ [ 3] local 192.168.40.214 port 1848 connected with 192.168.1.115 port 5001 [ ID] Interval Transfer Bandwidth [ 3] 0.0-10.0 sec 933 MBytes 782 Mbits/sec Much better, but still not really taking advantage of the full capabilities of the network. If the Linux box can reach 950 Mbits/sec consistently, this box should be able to as well. Also, if you're wondering about the medium, this is over the same cable...I'm switching back and forth. Any suggestion or ideas would be really welcome. Thanks!

  Read the article

• The RTL8111/8168B NIC under Linux and the r8168 driver

  - by nik

  So I've got one of the infamous R8168 Realtek ethernet NIC, which have some problems under Linux. After some research, I found out I had to use the r8168 driver for this card (and not the r8169 which still loads when nothing else is available), which I did. So now everything works fine... Sort of. My download and upload rates are more than halved compared to what I should get. When I test (with eg. speedtest) I get something like 20M (often 15M) in download and 30M in upload, but if I test under Windows (everything is otherwise identical: same ethernet cable, same connection, at the same time of the day (well 5 min apart)...), I get 50M upload/download (which is what I expect). Where can it come from? Here's some info: ~ # lspci [...] 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) ~ # modinfo r8168 filename: /lib/modules/3.2.1-gentoo-r2/net/r8168.ko version: 8.027.00-NAPI license: GPL description: RealTek RTL-8168 Gigabit Ethernet driver author: Realtek and the Linux r8168 crew <[email protected]> srcversion: 0A6E9F1D4E8E51DE4B6BEE3 alias: pci:v00001186d00004300sv00001186sd00004B10bc*sc*i* alias: pci:v000010ECd00008168sv*sd*bc*sc*i* depends: vermagic: 3.2.1-gentoo-r2 SMP mod_unload [...] ~ # mii-tool -v eth0: negotiated 100baseTx-HD, link ok product info: vendor 00:07:32, model 17 rev 4 basic mode: autonegotiation enabled basic status: autonegotiation complete, link ok capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD advertising: 100baseTx-HD 10baseT-FD 10baseT-HD flow-control link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD

  Read the article

• Adding a Second Wireless Router to an Existing Wired Network

  - by KVCrawford

  I apologize ahead of time, I know this has been asked before, but I'm still having problems...maybe you guys can help. I started out with the basic instructions from the highest-voted answer at http://serverfault.com/questions/41572/adding-a-second-wireless-router-to-my-network The new Wireless router in question is a Linksys Wireless-N Gigabit Router, Model # WRT310N Here are the steps I've taken in setting it up: Plug my laptop into LAN port #2 in the new router. Nothing else is connected at this point Configure the new router to be 192.168.1.200 (the original router is 192.168.1.1, and its DHCP clients are from 192.168.1.100-x.x.x.199) Set the internet connection on the new router to "DHCP Client" Turn off the DHCP server & NAT routing on the new router Plug in a LAN cable from the original router into the LAN port #1 on the new router (NOT the WAN port, nothing is plugged in there) Reset the new router Afterwards, I try to ping 192.168.1.1 from the laptop plugged into LAN port #2 on the new router, with no response. 192.168.1.200 garners no response either. Typing "ipconfig" tells me: Autoconfiguration IP Address: 169.254.198.113 Subnet Mask: 255.255.0.0 Default Gateway: 169.254.198.113 What's going wrong? I appreciate any help!

  Read the article

• Fresh Proxmox VE 2.1 installation with defaults can't be reached or pinged

  - by Damainman

  I am using the lastest Proxmox VE 2.1. My server has two NICS with a uplink only connected into eth0. My Server is a co-located server utilizing public IPv4 IPs. It is not behind a firewall or any system which monitors traffic. Via IPKVM I did a fresh install of Proxmox, I put in the correct IP, Mask, Gateway, and DNS information. The install went perfectly fine with no errors. Upon completion and rebooting the system: I am unable to reach the web GUI via the browser, it just times out. I am unable to ping the server. I am unable to ping outside to the Internet from within the server. Tried pinging out to 4.2.2.2 and yahoo.com I tried rebooting the server and restarting the network service. IFCONFIG shows my IP information under vmbro0 which also has the same MAC address as the eth0 device. eth0 only displays a IPv6 Scope:Link address, which I did not setup myself. This is my first time installing proxmox, but after searching for a few hours it doesn't seem like anyone else is having the same issue as me from a fresh install with just the defaults. So far the only thing I did was install it. Also, I know the network cable is good and the IP is good because I was running a Xen XCP server with the same network settings prior to wiping it to install proxmox. Some additional information: for pveversion -v (Installed proxmox-ve_2.1-f9b0f63a-26.iso) pve-manager: 2.1-1 (pve-manager/2.1/f9b0f63a) running kernel: 2.6.32-11-pve proxmox-ve-2.6.32: 2.0-66 netstat -nr (note: .136 is my network, and .137 is my gateway) Destination - Gateway - Genmask xxx.xxx.xxx.136 - 0.0.0.0 - 255.255.255.248 0.0.0.0 - xxx.xxx.xxx.137 - 0.0.0.0 /etc/network/interfaces auto lo iface lo inet loopback auto vmbr0 iface vmbr0 inet static address xxx.xxx.xxx.138 netmask 255.255.255.248 gateway xxx.xxx.xxx.137 bridge_ports eth0 bridge_stp off bridge_fd 0

  Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >