Search Results

Search found 7940 results on 318 pages for 'intel wireless'.

Page 69/318 | < Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >

  • Do I need a wifi card to have internet access?

    - by Sarah
    I am attempting to set up a wireless network on 11.04, freshly download today. The router is on and working. However, I do not have a wifi "card" (which I am assuming is a little USB-type thing that allows internet access, but correct me if I am wrong) and every time I try to type in the MAC address and everything, nothing works. I also get the "firmware missing" error when I scroll over the signal strength, which I have tried looking up but have been unsuccessful with completely understanding it. I guess my main question is do I need another little device to be able to use wifi on my ubuntu? I do have an ethernet cable but another person is using it and I do not want to be tied down to that cable. the problem is that none of the wireless networks show up, however they show up when I go into Windows mode on my laptop. I get an error message at the top saying "firmware missing" which I have tried looking up but still have no straight answer for.

    Read the article

  • Ubuntu 12.04, can't find my home wifi network

    - by Anton
    I've tried several solutions I found on the web, but didn't manage to solve a problem. Since today my laptop won't find my WiFi network, but neighbours' networks are suggested. Another laptop with U12.04 does find one. What do I do? I've Dell Latitude-E4310, 02:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01) Subsystem: Dell Inspiron M5010 / XPS 8300 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at f2c00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: brcmsmac Kernel modules: bcma, brcmsmac also NetworkManager Tool State: connected (global) - Device: eth1 ----------------------------------------------------------------- Type: 802.11 WiFi Driver: wl State: disconnected Default: no HW Address: 1C:65:9D:7A:45:5C Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Should I provide anything else? Many thanks in advance.

    Read the article

  • slow speed transfering files to a local network device

    - by F. Ariel Jung
    I'm having troubles copying files from my pc(ubuntu 13.04 64 bits) to a Media Center(WDTV Live: with an SATA2 HDD attached) through the local network. the speed is to slow, it's up to 2.0 MB/s image: http://s11.postimg.org/g1nuai92b/Captura_de_pantalla_de_2013_06_24_07_46_55.png (I don't use image tag because it is a big image) my PC has a wifi network card Tp Link TL-WN951N and it is connected to a TP Link TL-WDR3500 router via wifi, and the WDTV Live is connected via LAN here is a iwconfig: eth0 no wireless extensions. lo no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"TL-WDR3500" Mode:Managed Frequency:2.462 GHz Access Point: A0:F3:C1:6C:3B:F1 Bit Rate=39 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=62/70 Signal level=-48 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:33521 Invalid misc:2245290 Missed beacon:0 if more data is required I'll post it as needed. I can't figure this out, needed help. please

    Read the article

  • Ubuntu 13.10 and Dell Inspiron 7520 SE (Intel 4000 and ATI radeon HD 7730m)

    - by pjgowtham
    I installed 13.10 and i have problems with my display. Everything else works fine. I cant control my brightness. I thought the graphics driver is the problem. So i went to software updates, switched to another driver (proprietary) and the Ubuntu screen went black and i wasn't able to boot either. I cant use my lap with such low brightness. Then i reinstalled 13.10 again, This time full hdd reset. Same problem occurred. I grabbed radeon hd7730m for Linux x64 from the amd site, installed it, and the screen went black with only the "x" cursor showing on the next boot. What should i need to do to make my brightness work and stabilize graphic cards as mine is switchable graphics type.

    Read the article

  • Calling COM from Intel Fortran?

    - by user57460
    I'm trying to get COM working from my Fortran application. I do a "COMINITIALIZE" followed by a "COMCreateObjectByProgID". Both of these appear to be successful and return a status of zero. However, when I try to use the COM object, I get "Unhandled exception at 0x00000000 in FortranProg01.exe: 0xC0000005: Access violation." I realize that this error can mean almost anything, but has anyone got some suggestions of common problems with COM that produce this problem? Here are some more details. My program code: program FortranProg01 use myolepg implicit none integer*4 comInitStatus integer:: comCreateStatus INTEGER(INT_PTR_KIND()) $OBJECT INTEGER(4) funcResult REAL(8) pkgVersion call COMINITIALIZE(comInitStatus) print *, comInitStatus call COMCreateObjectByProgID('MyOlePg.MyOlePkg', $OBJECT, comCreateStatus) print *, comCreateStatus funcResult = IMyOlePkg_GetPackageVersion($OBJECT, pkgVersion) print *, funcResult call COMUNINITIALIZE() end program FortranProg01 The wizard-generated interface code: INTERFACE !property PackageVersion INTEGER(4) FUNCTION IMyOlePkg_GetPackageVersion($OBJECT, pVal) INTEGER(INT_PTR_KIND()), INTENT(IN) :: $OBJECT ! Object Pointer !DEC$ ATTRIBUTES VALUE :: $OBJECT REAL(8), INTENT(OUT) :: pVal !DEC$ ATTRIBUTES REFERENCE :: pVal !DEC$ ATTRIBUTES STDCALL :: IMyOlePkg_GetPackageVersion END FUNCTION IMyOlePkg_GetPackageVersion END INTERFACE Any help would be much appreciated! Thanks! Brad.

    Read the article

  • How to install Netgear N-300 UAB adapter WNA3100 on Ubuntu 12.04

    - by JacobusR
    After a fresh install of Ubuntu 12.04, the first thing I'm trying to do, is to setup my wireless adapter. I can see it using lsusb: beer@beer-linux:~$ lsusb ... Bus 002 Device 006: ID 0846:9020 NetGear, Inc. WNA3100(v1) Wireless-N 300 [Broadcom BCM43231] ... I have found a lot of dated instructions on the net and just wanted to know what the right way is to set it up on 12.04. I don't want to mess up a brand new install by tweaking things that don't need tweaking. According to most posts, you have to install the Windows drivers using the ndiswrapper package. Is this still the right way to go? If so, it would be great if someone could write down the steps to do this under 12.04

    Read the article

  • Update drivers for TL-WN851ND

    - by Tony_GPR
    Today I bought a new PCI wireless card, TP-Link WN851ND, with Atheros AR9227 chipset. It has 2 antennas and is compatible with Wifi N so I thought it would improve the quality of the signal. But after install it on my computer the result is the opposite to expected. It doesn't connect to my network, while my old Wifi BG card connect without problems, I created an access point from my smartphone to try the card, and work, but is very slow loading pages. In Windows 7 works perfectly, so I think the problem is the driver. I have Ubuntu 12.04 LTS with kernel 3.2.0.31, is there a way to update the driver or I can apply a patch to improve the performance of the card? Otherwise, anyone know if there is a work in progress to improve compatibility with this chipset, or is it better to change the card and buy one with better driver compatibility. And finally, which wireless N compatible chipsets have good support under Linux/Ubuntu?

    Read the article

  • Wifi networks will not show up!

    - by Kcahmadi
    I'm running Ubuntu 14.04 on an old '08 macbook. I've gone to system settingsSoftware & UpdatesAdditional Drivers and enabled the wireless driver. But when I click the wifi icon on the top toolbar no networks show up. When running lshw it clearly shows my wireless card under Network controller and it says the driver is installed. However, nm-tool only shows ethernet. And rfkill only shows bluetooth. What can I do?

    Read the article

  • Dual monitor setup with Intel graphics and Nvidia Geforce GT 425M on 12.04

    - by fo_x86
    I have a Dell XPS L401x and just installed 12.04. I have a mini-display and an HDMI output, and I could hook up two Dell UltraSharp monitors to each port on Windows 7, and get a triple monitor setup. Doing a bit of research, it seems like the mini-display is wired to the integrated graphics card whereas HDMI is hooked up to Nvidia graphics card. I've also installed Bumblebee as it seemed like that was the proper way of installing Nvidia drivers on Ubuntu. At the moment none of my monitors is being recognized by Ubuntu. Is it even possible to have a triple monitor (laptop display + 2 external) setup? Has anyone successfully done this?

    Read the article

  • How do I get the Netgear N150 USB wifi adapter working on 12.04?

    - by Jon
    Just installed latest version of ubuntu. I'm using a Netgear N150 Wireless USB Micro Adapter WNA1000M which keeps asking for network password over and over. I read elsewhere that I needed to install the latest driver for my chipset (RTL8188CUS) which I have and still no joy. If I run the steps listed in this thread while connected through ethernet, the wireless will connect just fine. If I disconnect the ethernet, the wifi will even continue to work, but after a restart or two I will lose connection. If I repeat the steps listed in the aforementioned thread, it will not re-connect wifi unless I run those steps while connected to ethernet.......so strange...

    Read the article

  • Cannot get Atheros AR9285 to work on 12.10

    - by user100449
    I've already went through all possible advices and still cannot start my Atheros AR9285 wireless card. I have a laptop Toshiba Portege Z830 where the WiFi already worked under Windows 7. But after migration on Ubuntu 12.10. I'm not able get it work. This is what I see on command lshw *-network UNCLAIMED description: Network controller product: AR9285 Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:c0500000-c050ffff This is what I see on command rfkill list 0: Toshiba Bluetooth: Bluetooth Soft blocked: yes Hard blocked: no 1: hci0: Bluetooth Soft blocked: yes Hard blocked: no Any idea?

    Read the article

  • Unstable Wifi and Spontaneous Low-graphic Error with Pavilion DV4

    - by Constant Dean
    I've been having numerous problems with connectivity through WiFi. It had been working for a few days and now it doesn't. On top of that around 40% of every time I turn on the laptop it shows "System running in low-graphics" error and I'm unable to view the desktop (sometimes not even able to access terminal), therefore having to manually power-down until it finally works. I use Ubuntu 12.10. nm-tool NetworkManager Tool State: connected (global) - Device: eth0 [Wired connection 1] ------------------------------------------- Type: Wired Driver: r8169 State: connected Default: yes HW Address: 84:34:97:6B:2E:D7 Capabilities: Carrier Detect: yes Speed: 10 Mb/s Wired Properties Carrier: on IPv4 Settings: Address: 192.168.1.10 Prefix: 24 (255.255.255.0) Gateway: 192.168.1.1 DNS: 192.168.1.1 DNS: 68.237.161.12 - Device: wlan0 ---------------------------------------------------------------- Type: 802.11 WiFi Driver: rt2800pci State: unavailable Default: no HW Address: 68:94:23:50:A5:D9 Capabilities: Wireless Properties WEP Encryption: yes WPA Encryption: yes WPA2 Encryption: yes Wireless Access Points

    Read the article

  • How to setup 802.11n wireless card in ubuntu

    - by michael
    Hi, I have installed ubuntu 9.10 on my laptop. It has a 802.11n wireless card. When I boot up to ubuntu, the wireless does not work. And if I connect to a wire network within ubuntu, it works. Can you please tell me how can I setup my wireless card in ubuntu 9.10? Thank you.

    Read the article

  • Network Manager troubleshooting

    - by Anero
    I'm having some issues when connecting to my house's wifi from my Ubuntu 10.10 laptop. If the connection doesn't exists, when selecting the network (and after entering the WPA2 password) I'm able to connect. Once the connection is saved, when trying to reconnect, Network Manager works for a minute or so and then fails; the only way to reconnect then is to delete the saved connection and re-select the network from the list of available wireless networks. The same network works with no issues on the same laptop when running Win7, and on other wireless networks when running Ubuntu. Is there a Network Manager log which I can take a look at for troubleshooting the issue? Are there any tools for checking the wifi status?

    Read the article

  • Ubuntu 12.04 crashes on startup for newer versions of Linux, possibly related to WiFi

    - by Jake
    My computer gets to the screen with the Ubuntu logo and the orange/white dots, and then the screen goes black, spits out a lot of error messages, and cannot boot. (If it'd be helpful, I can take a photo of my screen in this state.) I've found I can successfully boot if my wireless card is turned off. As soon as I turn it on, my computer crashes with the same black screen of death. I can also successfully boot if I choose "Previous Linux Version" and select a few versions back (I think 3.0.6). Here are some relevant details about my setup: Ubuntu 12.04 Computer: Lenovo x230 Wireless: Realtek RTL8188CE 802.11b/g/n WiFi Adapter Processor: Intel Core i5-3210M CPU @ 2.50GHz × 4 RAM: 16 GB of RAM Thank you!!!

    Read the article

  • How to Install Linux on my PC

    - by Holic
    Hi i need some help to install the drivers from my pc, on Ubuntu 10.10 i just installed it, and i a newbie on Ubuntu, but i understand a bit of Windows...but i want to try ubuntu and then Maybe change to UBUNTU!!! My hardware: QuadCore Intel Core i7-870, 3266 MHz (24 x 136) Asus P7P55D-E (2 PCI, 3 PCI-E x1, 2 PCI-E x16, 4 DDR3 DIMM, Audio, Gigabit LAN, IEEE-1394) NVIDIA GeForce GTX 480 (1536 MB) nVIDIA HDMI @ nVIDIA GF100 - High Definition Audio Controller VIA VT1828S @ Intel Ibex Peak PCH - High Definition Audio Controller [B-3] DIMM1: G Skill F3-12800CL9-2GBRL 2 GB DDR3-1333 DDR3 SDRAM (8-8-8-22 @ 609 MHz) (7-7-7-20 @ 533 MHz) (6-6-6-17 @ 457 MHz) DIMM3: G Skill F3-12800CL9-2GBRL 2 GB DDR3-1333 DDR3 SDRAM (8-8-8-22 @ 609 MHz) (7-7-7-20 @ 533 MHz) (6-6-6-17 @ 457 MHz) my pc is not connected to the internet with a wire(RJ45) but with a wireless LAn Asus WL-167G-V3(wich i also whant to install if possible) Anything would've help me :) Cheers & Thank you!

    Read the article

  • Attach Keyboard/Mouse to X Display in Dell XPS L502x Dual Video Cards (Intel/Nvidia HDMI)

    - by lcoronelp
    The idea: Use a second monitor in Dell XPS L502x with HDMI port in Ubuntu 12.04 The process: I connect the HDMI cable to monitor. I read this and I have video in HDMI monitor with Bumblebee and this commands: optirun nvidia-settings -c :8 DISPLAY=:8.0 firefox I have created a second keyboard/mouse master group with xinput with this solution. The problem: The second monitor (Display 8) doesn't recognize the keyboard/mouse and I cant use it. The question: Do you know some command to attach the keyboard/mouse master group to Display 8? I think that xinput -set-cs may work but it does not.

    Read the article

  • What does a media server need?

    - by DeaDSouL
    I want to buy a new PC to be used as a media server that streams HD movies, music to any wireless device on my network (laptop, desktop, TV, etc.). I was wondering about the PC hardware's specifications that I need to have so that it can work just fine? (It will be wireless) Is there any tutorial showing how it could be done? And the security - how can I secure it? As well as I need it to to host my emails. I mean I have many emails. And sometimes I'm using desktop, sometimes laptop.. so is it possible to make the server store a copy of my emails, attachments, all sent items (whether they were from desktop or laptop)?

    Read the article

  • Intel fields six-core embedded CPUs

    <b>LinuxDevices:</b> "The Xeon Processor 5600 series also includes the chipmaker's first six-core embedded processors, plus a dual-core processor for "micro servers" that has a TDP of only 30 Watts, the company says."

    Read the article

  • How to fix additional STA driver installation error on 12.04

    - by nibl
    I have a Broadcom BCM4313 wireless driver. It worked fine under 11.04 and the upgrade to 11.10 also went smoothly. The 12.04 upgrade has broken the wireless connection. I've seen several posts about this and all presume you can activate the STA drivers, but that's where it fails on this machine. The log is in /var/log/jockey.log: WARNING: modinfo for module wl failed: ERROR: modinfo: could not find module wl WARNING: /sys/module/wl/drivers does not exist, cannot rebind wl driver DEBUG: BroadcomWLHandler enabled(): kmod disabled, bcm43xx: blacklisted, b43: blacklisted, b43legacy: blacklisted (repeat of last error several times) Any ideas how to proceed?

    Read the article

  • Where are Wireless Profiles stored in Ubuntu

    - by LonnieBest
    Where does Ubuntu store profiles that allow it to remember the credentials to private wireless networks that it has previously authenticate to and used? I just replaced my Uncle's hard drive with a new one and installed Ubuntu 10.04 on it (he had Ubuntu 9.10 on his old hard drive. He is at my house right now, and I want him to be able to access his private wireless network when he gets home. Usually, when I upgrade Ubuntu, I have his /home directory on another partition, so his wireless profile to his own network persists. However, right now, I'm trying to figure out which .folder I need to copy from his /home/user folder on the old hard drive, to the new hard drive, so that he will be able to have wireless Internet when he gets home. Does anyone know with certainty, exactly which folder I need to copy to the new hard drive to achieve this?

    Read the article

< Previous Page | 65 66 67 68 69 70 71 72 73 74 75 76  | Next Page >