Search Results

Search found 3589 results on 144 pages for 'hp mini'.

Page 7/144 | < Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >

• No video output and no status light on HP Proliant Microserver

  - by tombull89

  I have an issue with a "N40L" HP Proliant Microserver. When the server is powered on the power light turns green but the machine's status light (the HP logo on the front) stays off and there is no video output through th onboard VGA. The system fan kicks in and if connected to a network the link light shows activity. I have no extra boards (iLO card, graphics card) only 4GB PNY non-standard stick of RAM.

  Read the article

• Random software/shutdown problems Mac mini

  - by Oliver

  Hello I have a Mac mini using OS X 10.5.8. Recently I've been having problems that are becoming increasingly severe. Particular symptoms: Firefox "quits" but the dot on the dock remains. If I try shutting down at this point I can't and have to use the power button. I can't start Firefox either. Significantly higher than normal crash rate for CS4 Illustrator Photoshop and Dreamweaver. If Firefox remains open when sleeping the Mac, on waking up firefox is completely unresponsive and must be restarted. Can cause problem 1. Today I lost all my FTP settings for Dreamweaver CS4 Bluetooth switches on when booting despite being switched off. Network password retention is somewhat erractic. Tried running Apple Hardware Test as described in the manual. Cannot access install disk by pressing D at startup. My pen tablet (Bamboo) lost my preferences. Tried unstalling software and now cannot re-install. I've never had problems of this level outside warranty before so I don't know much about debugging Macs. Solutions attempted: Disable bluetooth (see problem 5) Disable time machine Run appple harware test (see problem 7) Tried using activity monitor but don't know which processes are normal Tried uninstalling more recent software. I don't have any idea what to do. It seems like a hard disk failure but I don't have the know how to continue.

  Read the article

• HP P212 hangs on Initializing

  - by user927586

  I'm in trouble... Server: HP Microserver N36L Storage: HP P212/256 with BBWC Drives: 4 WD 2 Tb While expanding the RAID 5 array from 3 to 4 drives, the server rebooted itself. Expansion was at 76%. Now at boot the P212 seems to hang on initializing. After some time screen resets and the server boots, but in the os (Windows Server 2008R2) the P212 has errors (error code 10) and it's not seen by the HP ACU. Whats' going on? It's trying to complete the expansion? It's trying to make all over the expansion? It's simply stuck? What should I do? I NEED the data on the array! PS In the server BIOS, on the hd boot priority, the server still reports the array logical drive... maybe it's a good sign... PPS I'm not at the server physical location, so I cannot tell if the drives in the array are being accessed (that would be the case if the controller it's redoing/completing the expansion process) or not right now. Bye Dario

  Read the article

• Problem setting up HP PhotoSmart C4783

  - by ProfKaos

  I am trying to get several PC's on a network to connect to my client's new wireless printer, the C4783. I initially installed the whole HP 'tsumami of software' the comes with the printer onto my laptop, connected to the printer over USB, and corrected it's networking config. My laptop now also can connect to and print on the printer over the wireless network, as is intended for all PC's. However, when I try and install the HP software on my client's netbook, the HP software cannot find the printer. Firewall was turned off during this time, so doesn't play a role. I tried re-installing all software, but I initially only got a "Repair" or "Uninstall". Choosing Uninstall triggers a lengthy process that ends with a sudden and forceful restart, after which the same "Repair" or "Uninstall" choices are present. Looks like uninstall doesn't. Any suggestions as to how I can begin diagnosing why my laptop has no problem connecting to the printer, but two others do? Wireless is unsecured, and no, nobody has to know where I am right now. :-)

  Read the article

• HP Pavillion DV6500 recovery disk failure

  - by Scott W

  I recently attempted to re-install Windows Vista on an HP Pavillion DV6500 using the factory recovery DVD's, but encountered a strange problem. When the recovery disk attempted to reformat the hard disk, it failed at 22%. The error message provided was not very informative, just the error code "0x400110020000 1005". A google search turned up some people with a similar problem who asserted that HP has been know to ship corrupted recovery DVDs. The recovery disk did manage to reformat the the recovery partition before failing though, so recovering from the partition is no longer an option. It would be possible to reinstall from an off-the-shelf retail copy of Vista and then pull the drivers from HP's website, but I don't have access to a copy of Vista, and it would really be outrageous to have to purchase a new OS when I have a perfectly valid license already. Thought about biting the bullet and upgrading to Windows 7, but my understanding is that without Vista installed I'd be unable to use the upgrade version, and be forced to purchase the more expensive non-upgrade retail copy (!). Can anyone suggest a possible solution to this Catch-22? I've run out of ideas.

  Read the article

• hp proliant dl360 disk diagnostic issue

  - by user1039384

  We recently got two used drives (15000) and installed on our HP proliant dl360 G5 server. Created RAID1 and used HP SmartStart CD to perform diagnostics. Interestingly, the Diagnostic tab immidiately fails on Logical drive testing saying the Disk1 should be replaced, while the Test tab successfully runs all the complete tests on both disks and does not find any issue. At the meantime, when booting to esxi 5, vSphere periodically shows the Disk1 as Unknown and Logical drive in recovery process. This happens every 5-10 minutes. Here is the log from HP SmartScan diagnostic: 1 - Device, Test: Logical Drive 1, Storage Controller in Slot 0 1 - Description: The controller has reported a critical error in the drive error log. 1 - Recommended Repair: This drive should be replaced. 1 - Failed Count: 44 1 - Error code: F157 There is also another error log record (see below): 2 - Device, Test: test_components/libstorage.so ID 2 - Description: An unexpected exception occurred while performing an operation. Exception message: CISS_StatusHandler::evaluate: commandStatus = 4 (INVALID); hexdump of CISS_ErrorInfo: 00000000: __ __ 04 __ 20 __ __ __ __ __ __ __ __ __ __ __ .... ... ........ 00000010: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ 00000020: __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ ........ ........ Device: Hard Drive 2, Storage Controller in Slot 0 Property name: Bad Target Count 2 - Recommended Repair: Reboot or restart Insight Diagnostics. Retry the test. If the problem persists, upgrade to the latest version of Insight Diagnostics. 2 - Failed Count: 48 2 - Error Code: F62 Note that rebooting didn't help and I was running the latest diagnostic software version. Anyone has a clue? Is this a real disk issue? BTW, the controller is Smart Array E200i Thanks in advance

  Read the article

• HP DL185 - very slow disk read speed

  - by fistameeny

  Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

  Read the article

• HP Pavillion DV6500 recovery disk failure

  - by Scott W

  I recently attempted to re-install Windows Vista on an HP Pavillion DV6500 using the factory recovery DVD's, but encountered a strange problem. When the recovery disk attempted to reformat the hard disk, it failed at 22%. The error message provided was not very informative, just the error code "0x400110020000 1005". A google search turned up some people with a similar problem who asserted that HP has been know to ship corrupted recovery DVDs. The recovery disk did manage to reformat the the recovery partition before failing though, so recovering from the partition is no longer an option. It would be possible to reinstall from an off-the-shelf retail copy of Vista and then pull the drivers from HP's website, but I don't have access to a copy of Vista, and it would really be outrageous to have to purchase a new OS when I have a perfectly valid license already. Thought about biting the bullet and upgrading to Windows 7, but my understanding is that without Vista installed I'd be unable to use the upgrade version, and be forced to purchase the more expensive non-upgrade retail copy (!). Can anyone suggest a possible solution to this Catch-22? I've run out of ideas.

  Read the article

• HP LaserJet 1515: Disable "refill" warning

  - by Pekka

  I have a HP LaserJet 1515 connected to a Windows 7 PC. The Magenta cartridge is empty; the printer shows a warning to that effect, and won't let me print even black-and-white documents any more. I can't turn the warning off manually using the printer's small console: When I try to enter any menu, the display says "Menu access disabled". I have no idea why. There is a setting to override the warning, but it can't be changed using the Network interface in the browser (Although it is there on the status page) According to the manual,the HP printing tool is supposed to offer a switch for this, but it won't install on my Windows 7. It just rumbles about for half an hour, to magnificently exit with an "unknown error" requiring a reboot. On second look, the problem seems to be that Windows 7 just isn't supported. There is no download link for the tool when you specify Windows 7 as your OS. I just want to print a black-and-white-document on a printer whose black cartridge is still 65% full. Is this indeed impossible? On second thought, I'm cross-posting this on the HP support forum. I'll update here if anything comes up.

  Read the article

• hp ProLiant DL380 G6 server error code: 347 of array controller

  - by alhaythum

  I have got a bran new hp ProLiant DL380 G6 server with embedded smart array P410i controller, I got 164 GB SATA drives and wanted to change them with 300 GB SATA drives before installation. Now, we replace the drives and begin the configuration with the hp DVD and begin; when we reach the point that we want to save the configurations, an error message appears: "The operation has failed with an unknown error, please restart the application and attempt the operation again" When using Rescan System, this error message appears: "Status Alerts - Smart Array P410i in Embedded Slot Warning Status Message Code Description 347 The cache for Smart Array P410i Embedded Slot is not configured" We return back to the 164 GB SATA drives and the message just keeps appearing again. Any help please.

  Read the article

• How HP D2700 disk enclosure is monitored for alarms via SNMP

  - by VSAC

  We have HP D2700 disk enclosure and we would like to monitor D2700 (connected to HP Proliant DL360G8) for alarms.I have following questions regarding this. What are the options available for reporting D2700 hardware alarms (disk failure, power failure) via SNMP? We understand the D2700 to have an Ethernet interface for controller A and B and alarms are available via SNMP via this interface. Can anyone provide the actual alarms via this interface? (MIB and alarm list) As we have a number of D2700’s and would like to minimize the number of physical connections to the switch and associated IP addresses; Is there a mechanism to monitor the D2700 from the SCSI connected HPDL360 and raise SNMP alarms from the DL360 for hardware failures on the D2700? If so can anyone provide details and the actual alarms and MIB via this mechanism? Thanks!

  Read the article

• HP Blade ILO not responding in chassis ILO

  - by bobinabottle

  I have just started at a new company and I am inspecting their current server config. The HP 480c blades in a c7000 chassis aren't responding to ILO, although the chassis ILO is working fine. I have a feeling the last sysadmin configured the blades ILO as static IPs and it is not responding correctly. The servers are sitting in a datacenter and I'm hoping to be able to fix this remotely. Is there a way that I can change the ILO static IPs for the blades remotely? If not and I do have to go onsite, how do I change the IP addresses of the ILO for the blades? (Sorry I'm not very familiar with HP servers) thanks for you help!

  Read the article

• Creating a dynamic lacp trunk from HP Procurve 2412zl to Proliant DL380 G7

  - by Maalobs

  I'm configuring an IEEE 802.3ad (LACP) dynamic trunk from a HP Procurve 2412zl (firmware version K.15.07) switch to a HP Proliant DL380 G7 server. The DL380 has 4 NICs and is running Win2008 R2, so I'm teaming the NICs together and leaving everything on the recommended "automatic" setting in the HP NIC configuration tool. The server is one of two, they'll be connected on interfaces F17-F20 and F21-F24 respectively on the switch. I need the servers in a separate VLAN, here is the configuration for the VLAN: vlan 10 name "Lab_Mgmt" untagged B2,F17-F24 ip address 172.22.71.3 255.255.255.0 tagged B21 exit There is a DHCP-relay into the VLAN 10 from another device beyond interface B21. The Advanced Traffic Management Guide says that in order to run a dynamic LACP trunk on another VLAN besides the DEFAULT_VLAN, you need to first enable GVRP and then use "forbid" to stop the interfaces from automatically joining DEFAULT_VLAN when the dynamic trunk is created. GVRP brings some other stuff with it that I don't want or need, so I disable it with "unknown-vlans disable" on all other interfaces. Here is how I do it: procurve-5412zl-1(config)# gvrp procurve-5412zl-1(config)# interface A1-A24,B1-B24,C1-C24,D1-D10,D13-D24,E1-E24, F1-F16,K1,K2 unknown-vlans disable procurve-5412zl-1(config)# vlan 1 forbid F17-F24 procurve-5412zl-1(config)# interface F17-F20 lacp active The result afterwards looks all successful: procurve-5412zl-1(config)# show trunks Load Balancing Method: L3-based (Default), L2-based if non-IP traffic Port | Name Type | Group Type ---- + -------------------------------- --------- + ------ -------- F17 | XYZTEAM3_NIC1 100/1000T | Dyn2 LACP F18 | XYZTEAM3_NIC2 100/1000T | Dyn2 LACP F19 | XYZTEAM3_NIC3 100/1000T | Dyn2 LACP F20 | XYZTEAM3_NIC4 100/1000T | Dyn2 LACP procurve-5412zl-1(config)# vlan 10 procurve-5412zl-1(vlan-10)# show lacp LACP LACP Trunk Port LACP Admin Oper Port Enabled Group Status Partner Status Key Key ---- ------- ------- ------- ------- ------- ------ ------ F17 Active Dyn2 Up Yes Success 0 0 F18 Active Dyn2 Up Yes Success 0 0 F19 Active Dyn2 Up Yes Success 0 0 F20 Active Dyn2 Up Yes Success 0 0 On the Proliant server, the NIC configuration Tool is also indicating that a 802.3ad dynamic trunk has been established. Everything should be good, but it isn't. The server is not getting an IP-address from the DHCP, which it does if I'm not enabling LACP. If I configure the server to a static IP-address on the VLAN 10 subnet, it can't even ping the switch IP-address, much less anything outside of the VLAN. The switch can't ping the server either. I did another attempt with F17-F20 tagged, and checking the box "Default Native Tag (VLAN 10)" in the NIC configuration tool on the server, but there was no difference. Does anyone have any idea what I might have missed?

  Read the article

• Network Scanning: HP Laserjet 2840 & Windows 7 (+ Linux?)

  - by Eddie Parker

  I own a HP Laserjet 2840 multifunction printer. It's a fabulous device, but on Windows 7 it can't network scan. HP doesn't seem to support it in anything greater than Vista, and they aren't forth coming with solutions. I'm curious if anyone else has gotten work arounds to this problem. One possible avenue for me is that I have an always-on Gentoo server that is configured to see the printer as a fax and printer using hplip. I have this shared via samba and I can print just fine through samba. Is there a similar way I can do network scanning? Anyone know of where I start looking for this?

  Read the article

• How do I install an HP home-use printer on Windows Home Server (Windows Server 2003)

  - by Rob Allen

  I have an HP DeskJet F4210 printer that I would like to share on my network via Windows Home Server. Unfortunately, the driver installation checks for supported OS's, detects Home Server as Windows Server 2003 and exits. The driver install supports WinXP, W2k, Vista, and Win98SE. In theory, drivers for XP or Windows 2000 should work fine with Home Server. When using the "Install Printer" tool in Home Server I am only able to select .inf files (there are serveral on the install media) but the driver folders for XP and 2000 have .sys and .dll files. How can I bypass HP's short-sighted install program and get this printer up and running on Home server? I'll be happy with basic print functionality and will save the task of enabling scanning for another time.

  Read the article

• HP Pavilion dv3 volume control display driver on Windows 7

  - by Farinha

  I've recently bought an HP Pavilion dv3-2150ep and I'm having a hard time getting the volume control display to work as expected. The control is a back-lit touch-sensitive bar above the keyboard. Now the buttons to turn the volume up and down actually do it, but the lightning is not changing at all. The mute button does change color when toggled. I'm not sure if I'm missing any drivers here (I've installed all of those on the HP support page that seem to have something to do with sound and/or display) or if I have to activate this somewhere. Any ideas?

  Read the article

• HP DAT72x6 autoloader

  - by ericmayo

  Hoping someone here has seen this similar issue and can offer soem advise... I have an HP DAT72x6 auto loader tape backup unit. The external kind, here is a link to an owner's manual I found of it. http://www.dectrader.com/docs/set2/emr_na-c00070400-1.pdf I purchased the unit used about 6 months ago. The unit stopped working after 3-4 back-ups, it's used one day a month to do a monthly backup of another system. Suffice it to say the unit gets very little usage. There is an amber light on the front of the unit called the OAR (Operator Attention Required). The manual states to call for service when this light comes on and stays on. I've tried a few things to resolve but none are working. I've tried power cycling, re-securing the SCSI cables at both ends. Unit was used so I didn't pay much ($500) and so I don't want to spend a lot to have it fixed; might as well buy something new one if fixing this is going to cost more than $100-$150 bucks. I'm curious to see if anyone here has been around these devices or possibly is an HP repair person that can give me some things to try to resolve. The manual states that a solid amber OAR light indicates a hardware failure. When I power cycle the unit I see one of two scenarios so far. The unit powers up, shows self test in the LCD, then LCD changes to show all possible images and the OAR light comes on. The unit powers up, LCD is completely blank, the green lights go through some sort of process of going on and off and later the amber OAR light comes on and stays on. If it's a simple misalignment issue, I may be able to fix myself but not knowing what could cause the OAR light to come on gives me no where to even start. Google around gave no help either. I hoping someone here has experience with this and can help or point me in the right direction. Also, I don't have the HP Diagnostic tools mentioned in many manuals. The unit is connected to a Linux box. The 3-4 backups I've done with it so far have had no issues. We run amanda backup. Before this incident the unit was backing up and reading tapes fine. Thanks for any help or suggestions.

  Read the article

• Cannot Access Web Interface on HP 2510G

  - by Stephen

  I am currently setting up a new infrastructure with HP 2510s as edge switches and an HP E5406 as the main switch. I also have a DHCP and DNS server running on the same network. When i first set up one of my 2510 switches, I gave it a static IP through the console and then went to the web interface to continue my configuration. Later, I realized that I assigned it the wrong IP address, so i went through the web interface and changed the IP address to the correct one. Now, I can't access the web interface. I can telnet to the switch on the new IP address, but the web interface will not load. If I switch from static IP to DHCP, it loads the web interface. Any ideas on what could be causing the web server in the 2510 not to load with the new static IP address?

  Read the article

• HP ML115 with P400 Smart Array Controller

  - by John

  Hi, I have a HP ML115 server I have installed a HP P400 Smart Array Controller card, I also have 4 x 1TB Samsung Hard drives. I'm unable to get the the controller to detect the hard drives, I have changed the drives to SATA 1.5G without luck, I have also tried connecting a single 80GB Maxtor drive without luck The controller shows up just after boot and tries to initialize, The controller does not show up in the POST prompt, although I can see the controller when booting off a ACU CD THe controller firmware is a little old v4.12 but I have no way to update it. Any ideas on how I can get this going?

  Read the article

• Restoring factory image of HP Laptop

  - by Ahmed

  I use a HP G62. I am unable to use my recovery disk to restore to factory settings. I had no problems earlier until I created an additional partition which I hear might have changed my hard disk to dynamic. How do I get back to 'normal'? I don't mind formatting the disk. I just want my factory OS back. .............. i get an error message at about 69 percent telling me that the restoration process failed. I'm using the factory image disks i created using the hp recovery manager. I have tried formating the hard drive clean and then restoring woth the cd, it didn't work. I was always able to restore before i created that partition.

  Read the article

• HP 1210 Scan Button does nothing.

  - by Jack M.

  I have an HP 1210 all-in-one nightmare of a printer which has decided not to listen to the scan button anymore. I've dug into it, and see in the properties of the scanner in Windows XP that it says "No applications are registered for this event" under what to do when the Scan button is pressed. I've tried re-installing the HP software, didn't help. Updated the drivers off the website, and downgraded them to the ones on the CD, neither had an effect. Is there any way to tell Windows to just open the Scan/Cammera wizard when I press the Scan button on the printer? Windows XP SP3, if that matters.

  Read the article

• HP Envy 14, Ubuntu 10.10 and trouble with the graphics cards

  - by Carsten Gehling

  A few days ago I bought a HP Envy 14, containing 2 graphics card: An integrated Intel graphics card, and an ATI HD 5650. I've installed Ubuntu 10.10 32-bit on the machine. Most things work fine out of the box, but the graphics cards are giving me trouble. When booting, I get the message "failed to get i915 symbols, graphics turbo disabled". Then the screen blanks out during the remaining boot period. I am able to get the display working by changing to one of the consoles, then closing and opening the laptop's lid. It seems that Ubuntu gets confused about which card to use. I've read here: http://www.andreas-demmer.de/en/2010/07/18/testbericht-linux-auf-dem-hp-envy-14 that I should be able to turn off one the cards by echoing keywords into /sys/kernel/debug/vgaswitcheroo/switch, but that path is not available on my system. The BIOS does not have any methods to switch of the ATI card. Help anyone? /Carsten

  Read the article

• HP Photosmart 7450 Prints Noise On Windows 7 Pro 64-bit

  - by David Mackintosh

  I have received a working (in its last location) HP Photosmart 7450 printer. I connected it up to my Windows 7 Pro 64-bit workstation, and the driver was (apparently) installed. The problem is that whenever I try to print from it -- test page, text from notepad, picture, whatever -- it spins through a half dozen sheets of paper, some of which have fractions of text on them, but most of which are either blank or have line noise printed on them. Noise similar to what was printed out on ye olde laserjet printers when the postscript interpreter failed. HP's web site only has a "use the included driver in Windows 7, be happy" instruction. The driver has been removed and added several times. The printer was previously attached to a XP Home computer and worked correctly without incident. Does anyone have any ideas for troubleshooting before I drop this printer in the river?

  Read the article

• Convert RAID-0 to RAID-1 on HP ML350G6 with P410i zero memory

  - by JLe

  I have an HP ML350 G6 with a P410i zero memory RAID controller. As far as I can understand that means I can't expand a current single drive "RAID-0" configuration to a RAID-1 using the HP Offline ACU without installing memory and BBWC. Is that correct? What makes me think about this is the fact that expanding RAID-0 to RAID-1 should be pretty similar to replacing a failed drive in an already existing RAID-1? So then why can't I expand without memory and BBWC? Is my best option otherwise to (i) use Ghost to capture the disk, create a new RAID-1 with the existing drive and a new one or (ii) buy memory+BBWC and do it online? Thanks

  Read the article

• HP CM2320 Printer crashes windows 2003 spooler in TS/Citrix

  - by Stephane

  Hello, I'm having a very annoying issue with an HP printer (CM2320): all of a sudden, any user who has that printer installed locally as default printer would crash any Windows 2003 terminal services or Citrix server (XenApp PS 4.5) as soon as he connect, causing the session to hang and other users to be unable to connect to the server. To restore functionality, an administrator has to connect to the server's console session and acknowledge the error message about spoolsv.exe having crashed with an AV. I tried downloading the latest drivers from HP (an adventure worthy of Lara Croft in itself) and install it on all servers but that didn't seem to have helped the situation: the spooler is still crashing. Anyone has a suggestion about what I could do about this ?

  Read the article

< Previous Page | 3 4 5 6 7 8 9 10 11 12 13 14  | Next Page >