Search Results

Search found 9398 results on 376 pages for 'matt dev'.

Page 70/376 | < Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >

• Why do I see a large performance hit with DRBD?

  - by BHS

  I see a much larger performance hit with DRBD than their user manual says I should get. I'm using DRBD 8.3.7 (Fedora 13 RPMs). I've setup a DRBD test and measured throughput of disk and network without DRBD: dd if=/dev/zero of=/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 4.62985 s, 116 MB/s / is a logical volume on the disk I'm testing with, mounted without DRBD iperf: [ 4] 0.0-10.0 sec 1.10 GBytes 941 Mbits/sec According to Throughput overhead expectations, the bottleneck would be whichever is slower, the network or the disk and DRBD should have an overhead of 3%. In my case network and I/O seem to be pretty evenly matched. It sounds like I should be able to get around 100 MB/s. So, with the raw drbd device, I get dd if=/dev/zero of=/dev/drbd2 bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 6.61362 s, 81.2 MB/s which is slower than I would expect. Then, once I format the device with ext4, I get dd if=/dev/zero of=/mnt/data.tmp bs=512M count=1 oflag=direct 536870912 bytes (537 MB) copied, 9.60918 s, 55.9 MB/s This doesn't seem right. There must be some other factor playing into this that I'm not aware of. global_common.conf global { usage-count yes; } common { protocol C; } syncer { al-extents 1801; rate 33M; } data_mirror.res resource data_mirror { device /dev/drbd1; disk /dev/sdb1; meta-disk internal; on cluster1 { address 192.168.33.10:7789; } on cluster2 { address 192.168.33.12:7789; } } For the hardware I have two identical machines: 6 GB RAM Quad core AMD Phenom 3.2Ghz Motherboard SATA controller 7200 RPM 64MB cache 1TB WD drive The network is 1Gb connected via a switch. I know that a direct connection is recommended, but could it make this much of a difference? Edited I just tried monitoring the bandwidth used to try to see what's happening. I used ibmonitor and measured average bandwidth while I ran the dd test 10 times. I got: avg ~450Mbits writing to ext4 avg ~800Mbits writing to raw device It looks like with ext4, drbd is using about half the bandwidth it uses with the raw device so there's a bottleneck that is not the network.

  Read the article

• perl hide system output

  - by Chris

  Using perl 5.8.8 on linux, need the output of a perl 'system' command to be hidden. The command in my code is : system("wget", "$url", "-Omy_folder/$date-$target.html", "--user-agent=$useragent"); I've tried using " /dev/null 2&1" in different places in the system command, like this- system("wget", "$url", "-Omy_folder/$date-$target.html", "--user-agent=$useragent"," /dev/null 2&1"); Can anyone help me with where the redirection to /dev/null should be?

  Read the article

• Xen kernel can't see 2 disks of 6 of 1TB, does it have a limitation?

  - by PartySoft

  Linux gentoo-xen 2.6.18-xen-r12 #3 SMP Tue Oct 5 09:28:53 PDT 2010 x86_64 Intel(R) Xeon(R) CPU E5506 @ 2.13GHz GenuineIntel GNU/Linux I have 6 disks of 1 TB and i can't see all of them only 4, can anyone give me an ideea what can i do ? Filesystem Size Used Avail Use% Mounted on rootfs 886G 4.4G 836G 1% / /dev/sda3 886G 4.4G 836G 1% / rc-svcdir 1.0M 44K 980K 5% /lib64/rc/init.d shm 7.9G 0 7.9G 0% /dev/shm /dev/sdb1 917G 200M 871G 1% /home2 /dev/sdc1 917G 200M 871G 1% /home3 /dev/sdd1 917G 200M 871G 1% /home4 The hardware is Dual xeon E5506 processors on a supermicro X8DTL mobo 4.346585] ata3.00: ATA-8, max UDMA/133, 1953525168 sectors: LBA48 NCQ (depth 0/32) [ 4.346588] ata3.00: ata3: dev 0 multi count 16 [ 4.352861] ata3.00: configured for UDMA/133 [ 4.352867] scsi3 : ata_piix [ 4.352875] PM: Adding info for No Bus:host3 [ 4.510584] ata4.00: ATA-8, max UDMA/133, 1953525168 sectors: LBA48 NCQ (depth 0/32) [ 4.510587] ata4.00: ata4: dev 0 multi count 16 [ 4.516848] ata4.00: configured for UDMA/133 [ 4.516861] PM: Adding info for No Bus:target2:0:0 [ 4.516905] Vendor: ATA Model: SAMSUNG HD103SJ Rev: 1AJ1 [ 4.516910] Type: Direct-Access ANSI SCSI revision: 05 [ 4.516920] PM: Adding info for scsi:2:0:0:0 [ 4.517452] SCSI device sde: 1953525168 512-byte hdwr sectors (1000205 MB) [ 4.517460] sde: Write Protect is off [ 4.517461] sde: Mode Sense: 00 3a 00 00 [ 4.517478] SCSI device sde: drive cache: write back [ 4.517514] SCSI device sde: 1953525168 512-byte hdwr sectors (1000205 MB) [ 4.517521] sde: Write Protect is off [ 4.517522] sde: Mode Sense: 00 3a 00 00 [ 4.517532] SCSI device sde: drive cache: write back [ 4.517534] sde: sde1 [ 4.524551] sd 2:0:0:0: Attached scsi disk sde [ 4.524855] sd 2:0:0:0: Attached scsi generic sg4 type 0 [ 4.524874] PM: Adding info for No Bus:target3:0:0 [ 4.524928] Vendor: ATA Model: SAMSUNG HD103SJ Rev: 1AJ1 [ 4.524933] Type: Direct-Access ANSI SCSI revision: 05 [ 4.524946] PM: Adding info for scsi:3:0:0:0 [ 4.525216] SCSI device sdf: 1953525168 512-byte hdwr sectors (1000205 MB) [ 4.525227] sdf: Write Protect is off [ 4.525228] sdf: Mode Sense: 00 3a 00 00 [ 4.525242] SCSI device sdf: drive cache: write back [ 4.525280] SCSI device sdf: 1953525168 512-byte hdwr sectors (1000205 MB) [ 4.525286] sdf: Write Protect is off [ 4.525289] sdf: Mode Sense: 00 3a 00 00 [ 4.525301] SCSI device sdf: drive cache: write back [ 4.525302] sdf: sdf1 [ 4.532691] sd 3:0:0:0: Attached scsi disk sdf [ 4.533010] sd 3:0:0:0: Attached scsi generic sg5 type 0 [ 4.977669] scsi: <fdomain> Detection failed (no card) [ 5.030479] GDT-HA: Storage RAID Controller Driver. Version: 3.05 [ 5.030635] GDT-HA: Found 0 PCI Storage RAID Controllers [ 5.372350] Fusion MPT base driver 3.04.01 [ 5.372358] Copyright (c) 1999-2005 LSI Logic Corporation [ 5.579176] Fusion MPT SPI Host driver 3.04.01 [ 5.881777] ieee1394: Initialized config rom entry `ip1394' [ 6.166745] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) [ 6.166748] ieee1394: sbp2: Try serialize_io=0 for better performance [ 6.428866] md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 [ 6.428872] md: bitmap version 4.39 [ 6.431518] md: raid0 personality registered for level 0 [ 6.495979] md: raid1 personality registered for level 1 [ 6.570270] raid5: automatically using best checksumming function: generic_sse [ 6.575523] generic_sse: 6608.000 MB/sec [ 6.575526] raid5: using function: generic_sse (6608.000 MB/sec) [ 6.596226] raid6: int64x1 1835 MB/s [ 6.613231] raid6: int64x2 1773 MB/s [ 6.630256] raid6: int64x4 1675 MB/s [ 6.647296] raid6: int64x8 1027 MB/s [ 6.664267] raid6: sse2x1 3578 MB/s [ 6.681268] raid6: sse2x2 4207 MB/s [ 6.698280] raid6: sse2x4 4625 MB/s [ 6.698281] raid6: using algorithm sse2x4 (4625 MB/s) [ 6.698285] md: raid6 personality registered for level 6 [ 6.698286] md: raid5 personality registered for level 5 [ 6.698288] md: raid4 personality registered for level 4 [ 6.781090] md: raid10 personality registered for level 10 [ 7.007043] Intel(R) PRO/1000 Network Driver - version 7.1.9-k4 [ 7.007046] Copyright (c) 1999-2006 Intel Corporation. [ 9.229465] kjournald starting. Commit interval 5 seconds [ 9.229476] EXT3-fs: mounted filesystem with ordered data mode.

  Read the article

• Limiting bandwidth on internal interface on Linux gateway

  - by Jack Scott

  I am responsible for a Linux-based (it runs Debian) branch office router that takes a single high-speed Internet connection (eth2) and turns it into about 20 internal networks, each with a seperate subnet (192.168.1.0/24 to 192.168.20.0/24) and a seperate VLAN (eth0.101 to eth0.120). I am trying to restrict bandwidth on one of the internal subnets that is consistently chewing up more bandwidth than it should. What is the best way to do this? My first try at this was with wondershaper, which I heard about on SuperUser here. Unfortunately, this is useful for exactly the opposite situation that I have... it's useful on the client side, not on the Internet side. My second attempt was using the script found at http://www.topwebhosts.org/tools/traffic-control.php, which I modified so the active part is: tc qdisc add dev eth0.113 root handle 13: htb default 100 tc class add dev eth0.113 parent 13: classid 13:1 htb rate 3mbps tc class add dev eth0.113 parent 13: classid 13:2 htb rate 3mbps tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip dst 192.168.13.0/24 flowid 13:1 tc filter add dev eth0.113 protocol ip parent 13:0 prio 1 u32 match ip src 192.168.13.0/24 flowid 13:2 What I want this to do is restrict the bandwidth on VLAN 113 (subnet 192.168.13.0/24) to 3mbit up and 3mbit down. Unfortunately, it seems to have no effect at all! I'm very inexperienced with the tc command, so any help getting this working would be appreciated.

  Read the article

• external hard drive is no longer recognized, gives buffer I/O errors

  - by BioGeek

  Hi all, The external hard drive which contains all my photos and where I backed-up all my important documents is no longer recognized. It is a three month old 500GB Iomage Prestige Desktop Hard Drive. When I plug it in, it is recognised as a USB device, because it shows up when I type lsusb, but dmesg gives this error message. [19712.013250] usb 2-2: new high speed USB device using ehci_hcd and address 21 [19712.145347] usb 2-2: configuration #1 chosen from 1 choice [19712.147214] scsi25 : SCSI emulation for USB Mass Storage devices [19712.147514] usb-storage: device found at 21 [19712.147519] usb-storage: waiting for device to settle before scanning [19717.148978] usb-storage: device scan complete [19717.149527] scsi 25:0:0:0: Direct-Access ST350082 0AS PQ: 0 ANSI: 2 CCS [19717.151020] sd 25:0:0:0: Attached scsi generic sg2 type 0 [19717.151685] sd 25:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB) [19717.160402] sd 25:0:0:0: [sdb] Write Protect is off [19717.160412] sd 25:0:0:0: [sdb] Mode Sense: 34 00 00 00 [19717.160418] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165685] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19717.165691] sdb: sdb1 [19719.171808] sd 25:0:0:0: [sdb] Assuming drive cache: write through [19719.171818] sd 25:0:0:0: [sdb] Attached SCSI disk [19737.430998] sd 25:0:0:0: [sdb] Unhandled sense code [19737.431007] sd 25:0:0:0: [sdb] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [19737.431016] sd 25:0:0:0: [sdb] Sense Key : Medium Error [current] [19737.431027] sd 25:0:0:0: [sdb] Add. Sense: Unrecovered read error [19737.431038] end_request: I/O error, dev sdb, sector 6160463 [19737.431050] Buffer I/O error on device sdb1, logical block 6160400 [19737.431060] Buffer I/O error on device sdb1, logical block 6160401 [19737.431067] Buffer I/O error on device sdb1, logical block 6160402 [19737.431075] Buffer I/O error on device sdb1, logical block 6160403 [19737.431082] Buffer I/O error on device sdb1, logical block 6160404 [19737.431088] Buffer I/O error on device sdb1, logical block 6160405 [19737.431096] Buffer I/O error on device sdb1, logical block 6160406 [19737.431102] Buffer I/O error on device sdb1, logical block 6160407 [19737.431114] Buffer I/O error on device sdb1, logical block 6160408 [19737.431121] Buffer I/O error on device sdb1, logical block 6160409 [19737.712183] sd 6:0:0:0: [sdb] Unhandled sense code [19737.712191] sd 6:0:0:0: [sdb] Result: hostbyte=DID_ERROR driverbyte=DRIVER_SENSE [19737.712200] sd 6:0:0:0: [sdb] Sense Key : Hardware Error [current] [19737.712210] sd 6:0:0:0: [sdb] Add. Sense: No additional sense information [19737.712222] end_request: I/O error, dev sdb, sector 0 [19737.712232] Buffer I/O error on device sdb, logical block 0 Neither does the external drive show when I use fdisk: jeroen@phalacrocorax:~$ sudo fdisk -l [sudo] password for jeroen: Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x000341ad Device Boot Start End Blocks Id System /dev/sda1 * 1 18714 150320173+ 83 Linux /dev/sda2 18715 19457 5968147+ 5 Extended /dev/sda5 18715 19457 5968116 82 Linux swap / Solaris` I popped the disk out of the casing put it on a SATA connect internally and then tried the file recovery programs testdisk/photorec and SpinRite, but both failed because they couldn't recognize the external harddisk. Do I have any other options?

  Read the article

• How to mount vfat drive on Linux with ownership other than root?

  - by Norman Ramsey

  I'm running into trouble mounting an iPod on a newly upgraded Debian Squeeze. I suspect either a protocol has changed or I've tickled a bug, which I don't know where to report. I'm trying to mount the iPod so that I have permission to read and write it. But my efforts come to nothing: $ sudo mount -v -t vfat -o uid=32074,gid=6202 /dev/sde2 /mnt /dev/sde2 on /mnt type vfat (rw,uid=32074,gid=6202) $ ls -l /mnt total 80 drwxr-xr-x 2 root root 16384 Jan 1 2000 Calendars drwxr-xr-x 2 root root 16384 Jan 1 2000 Contacts drwxr-xr-x 2 root root 16384 Jan 1 2000 Notes drwxr-xr-x 3 root root 16384 Jun 23 2007 Photos drwxr-xr-x 6 root root 16384 Jun 19 2007 iPod_Control $ sudo umount /mnt $ sudo mount -v -t vfat -o uid=nr,gid=nr /dev/sde2 /mnt /dev/sde2 on /mnt type vfat (rw,uid=32074,gid=6202) $ ls -l /mnt total 80 drwxr-xr-x 2 root root 16384 Jan 1 2000 Calendars drwxr-xr-x 2 root root 16384 Jan 1 2000 Contacts drwxr-xr-x 2 root root 16384 Jan 1 2000 Notes drwxr-xr-x 3 root root 16384 Jun 23 2007 Photos drwxr-xr-x 6 root root 16384 Jun 19 2007 iPod_Control As you see, I've tried both symbolic and numberic IDs, but the files persist in being owned by root (and only writable by root). The IDs are really mine; I've had the UID since 1993. $ id uid=32074(nr) gid=6202(nr) groups=6202(nr),0(root),2(bin),4(adm),... I've put an strace at http://pastebin.com/Xue2u9FZ, and the mount(2) call looks good: mount("/dev/sde2", "/mnt", "vfat", MS_MGC_VAL, "uid=32074,gid=6202") = 0 Finally, here's my kernel version from uname -a: Linux homedog 2.6.32-5-686 #1 SMP Mon Jun 13 04:13:06 UTC 2011 i686 GNU/Linux Does anyone know if I should be doing something different, or If there is a workaround, or If this is a bug, where it should be reported?

  Read the article

• linux refused to mount a valid partition

  - by greg

  My setup is a linux box with 1 partition used thought LVM - has been working for years. I add a freeze and after the reboot the partition cannot be mounted: mount -r -t ext3 /dev/pve/data /mnt/pve-data mount: wrong fs type, bad option, bad superblock on /dev/mapper/pve-data, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so However fsck doesn't see any problem with it: fsck.ext3 -fp /dev/pve/data /dev/pve/data: 3024076/60366848 files (0.6% non-contiguous), 156921642/241435648 blocks There's nothing in dmegs nor the syslog. I'm puzzled, what's wrong with my partition? Thanks in advance greg debian 5.0.10 LVM 2.02.39

  Read the article

• needing storage integrity (write/read) test - for BASH

  - by Mr. Bash

  In need of shell scripts / bash commands to verify data integrity of local harddrives, usb-drives, etc, ... Like the famous www.heise.de/download/h2testw; or something that is at least common within repositories. (h2testw writes a specific datastring over and over onto the medium, then reads it again to verify if it was written correctly and displays write/read time/speed.) please no dd if=/dev/random of=/dev/sdx bs=1k && dd if=/dev/sdx of=/dev/null bs=1k since it won't verify if everything was written correctly. It is only a test if read/write is successful to the device. So far, I'm not too happy with badblocks -w -v /dev/sdx1 either, since it seems rather slow and I don't know what it exactly writes, and if it considers wear-leveling on flash media. There is also a program named F3 http://oss.digirati.com.br/f3/ that needs to be compiled. Designed after h2testw, the concept sounds interesting, i'd just rather have it as a ready to go bash script.

  Read the article

• Different block sizes for partition and underlying logical disk on HP Raid Controller (Linux)

  - by Wawrzek

  Following links collected in this thread I started to check blockdev and found the following output indicating different sizes for partition c0d9p1 and the underlying device (c0d9): [root@machine ~]# blockdev --report /dev/cciss/c0d9 RO RA SSZ BSZ StartSec Size Device rw 256 512 4096 0 3906963632 /dev/cciss/c0d9 [root@machine ~]# blockdev --report /dev/cciss/c0d9p1 RO RA SSZ BSZ StartSec Size Device rw 256 512 2048 1 3906959039 /dev/cciss/c0d9p1 We have a lot of small files, so yes the block size is smaller than normal. The device is a logical driver on an HP P410 raid controller, simple disk without any raid - RAID 0 on one disk to be precise. (Please note that above configuration is a feature not a bug). Therefore, I have the following questions. Can the above discrepancy in the block size affect disk performance? Can I control the block size using hpacucli?

  Read the article

• Merge LVM Partition with unallocated Space

  - by David

  I have a linux hard drive with three areas: /dev/hda1 - ext3 boot partition (20 MB) /dev/hda2 - lvm2 main partition (6 GB) unpartitioned space - 12 GB I would like to merge the unpartitioned space into the lvm2 partition known as /dev/hda2. I tried using GParted, but it does not support lvm2. What commands or utilities could I use to add the unpartitioned space to hda2 without losing my existing data?

  Read the article

• Free space on Dedi' in CentOS

  - by Trance84

  It will sound stupid but i need to figure out how much disk space i have in my dedicated server, it runs CentOS6...the last command i issued was this [root@ks34900 ~]# df -h Filesystem Size Used Avail Use% Mounted on rootfs 9.7G 6.4G 2.9G 69% / /dev/root 9.7G 6.4G 2.9G 69% / none 1000M 288K 1000M 1% /dev /dev/sda2 914G 200M 868G 1% /home But again, stupid as it may sound... i cant figure out how much space i have in "/" folder (root) And is it possible that "/usr" have a different space (partition)?

  Read the article

• Restoring a Ubuntu Linux LVM drive

  - by user848106

  Scenario: I have a hard disk with a bootable sda1 partition and an Linux LVM. I seem to have corrupted the MBR? or Grub? not sure. I know it no longer boots and even with boot-repair and a Ubuntu live usb I was able to restore it. Following a "fix" with boot-repair I get "missing operating system" Can't i just reinstall grub or a new menu.lst? Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders, total 625142448 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x0007b68f Device Boot Start End Blocks Id System /dev/sda1 * 2048 499711 248832 83 Linux /dev/sda2 501758 625141759 312320001 5 Extended /dev/sda5 501760 625141759 312320000 8e Linux LVM

  Read the article

• Is it possible to mount a disk image, created with dd, to a directory on a mounted external usb hdd?

  - by Keeper Hood

  I have an image of my home (/dev/sda3) partition, which I've created using the "dd" command. dd if=/dev/sda3 of=/path/to/disk.img I've deleted the home partition via gparted in order to enlarge my /dev/root partition. Then I've recreated the /dev/sda3 partition which is smaller in size then the one I've backed up to the image. I was wondering since I have a 2TB external HDD, could it be possible to mount my backed up image on the external HDD and then copy the files into the /home directory. Since the external HDD would be already in a "mounted state", I'm unsure whether this is a good idea, mounting on a mounted device. I'm running Slackware 13.37 (64bit). used ext4 on all the partitions. resized the root partition with gparted live cd. I've tried mount -t ext4 /path/to/disk.img /mng/image -o loop It gave me an fs error (wrong fs type, bad option, bad superblock on dev/loop/0) Then i did dmesg | tail which outputs: EXT4-fs (loop0) : bad geometry: block count 29009610 exceeds size of defice (1679229 blocks) I have no idea what to do, I want to restore my /home data from the image I've backed up.

  Read the article

• PLesk Error: pmm-ras error (Error code = -6): during restore.. /tmp folder to increase?

  - by eric

  I had to re-install plesk on a centos 6 system after a crash. The full backup file is 11 gb. but at the beginning of the backup reinstall I get the error Error: pmm-ras error (Error code = -6): argh ! my disk organization is like this Filesystem Size Used Avail Use% Mounted on /dev/xvda1 3.7G 801M 2.9G 22% / /dev/mapper/vg00-usr 14G 1.5G 12G 12% /usr /dev/mapper/vg00-var 155G 14G 134G 10% /var /dev/mapper/vg00-home 3.9G 136M 3.6G 4% /home none 1000M 7.5M 993M 1% /tmp I suppose I have to increase my /tmp folder to accept the backup size,but I don't know how-to. I'm on 1&1 cloud server Thanks for your help. You can imagine the emergency of this situation...

  Read the article

• EC2: How dangerous is it to turn off fsck for EBS volumes?

  - by Janine

  I have been tearing my hair out trying to figure out why my EC2 instances (made from my own custom AMIs) were taking many tries to come up properly. They would fail with the following error: fsck.ext3: No such file or directory while trying to open /dev/sdf For both of the EBS volumes I was attaching during startup. Finally, I figured out the problem. I had put this in /etc/fstab: /dev/sdf /export ext3 defaults 1 2 /dev/sdi /export2 ext3 defaults 1 2 The 2 tells the system to fsck the drives on the way up. Changing this to /dev/sdf /export ext3 defaults 1 0 /dev/sdi /export2 ext3 defaults 1 0 Avoids the problem completely, but now the volumes are never going to be fsck'd. How much does this matter? Once the instance goes into production it's going to be running pretty much 24/7, so not many fscks would be happening anyway, but still... this just feels like a bad idea. I have not been able to find anyone else even reporting this problem (there are people with the same error message, but different causes). It seems unbelievable that I could be the only person to ever make this mistake, but perhaps I'm just talented that way. :) If there is another solution to the problem I would love to hear it; I have not been able to find one.

  Read the article

• Under kvm, Vista guest OS install halts on black screen

  - by Isaac Sutherland

  I am using kvm on my ubuntu-server-10.04 amd64 dual core PC. I am trying to install a Windows Vista guest OS. The installation proceeds properly until the system reboot halfway into the installation process, at which point it stops on a black screen and CPU usage goes to near zero. I created the vm with virt-install as follows: virt-install -n vista --connect qemu:///system -r 1024 -vcpus 2 \ --os-type windows --os-variant vista \ --virt-type kvm --accelerate \ -c /dev/sr0 \ --disk path=/dev/main/vista-hd \ --network bridge=br0 \ --vnc --noautoconsole Where /dev/sr0 is the physical drive with the vista installation DVD, and /dev/main/vista-hd is a 20-GB lvm logical volume I created. A number of people seem to have had success installing vista under KVM, but I haven't been able to determine what is causing my problem. Ideas anyone?

  Read the article

• RAID 50 24Port Fast Writes Slow Reads - Ubuntu

  - by James

  What is going on here?! I am baffled. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/dev/zero of=/Volumes/MercuryInternal/test/test.fs bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 57.0948 s, 735 MB/s serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/Volumes/MercuryInternal/test/test.fs of=/dev/null bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 116.189 s, 361 MB/s OF NOTE: My RAID50 is 3 sets of 8 disks. - This might not be the best config for SPEED. OS: Ubuntu 12.04.1 x64 Hardware Raid: RocketRaid 2782 - 24 Port Controller HardDriveType: Seagate Barracuda ES.2 1TB Drivers: v1.1 Open Source Linux Drivers. So 24 x 1TB drives, partitioned using parted. Filesystem is ext4. I/O scheduler WAS noop but have changed it to deadline with no seemingly performance benefit/cost. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo gdisk -l /dev/sdb GPT fdisk (gdisk) version 0.8.1 Partition table scan: MBR: protective BSD: not present APM: not present GPT: present Found valid GPT with protective MBR; using GPT. Disk /dev/sdb: 41020686336 sectors, 19.1 TiB Logical sector size: 512 bytes Disk identifier (GUID): 95045EC6-6EAF-4072-9969-AC46A32E38C8 Partition table holds up to 128 entries First usable sector is 34, last usable sector is 41020686302 Partitions will be aligned on 2048-sector boundaries Total free space is 5062589 sectors (2.4 GiB) Number Start (sector) End (sector) Size Code Name 1 2048 41015625727 19.1 TiB 0700 primary To me this should be working fine. I can't think of anything that would be causing this other then fundamental driver errors? I can't seem to get much/if any higher then the 361MB a second, is this hitting the "SATA2" link speed, which it shouldn't given it is a PCIe2.0 card. Or maybe some cacheing quirk - I do have Write Back enabled. Does anyone have any suggestions? Tests for me to perform? Or if you require more information, I am happy to provide it! This is a video fileserver for editing machines, so we have a preference for FAST reads over writes. I was just expected more from RAID 50 and 24 drives together... EDIT: (hdparm results) serveradmin@FILESERVER:/Volumes/MercuryInternal$ sudo hdparm -Tt /dev/sdb /dev/sdb: Timing cached reads: 17458 MB in 2.00 seconds = 8735.50 MB/sec Timing buffered disk reads: 884 MB in 3.00 seconds = 294.32 MB/sec EDIT2: (config details) Also, I am using a RAID block size of 256K. I was told a larger block size is better for larger (in my case large video) files. EDIT3: (Bonnie++ Results. Would love some guidance with this!)

  Read the article

• Assets not served - Apache Reverse proxy - Diaspora

  - by Matt

  I have succeeded in installing Diaspora* on my subdomain diaspora.mattaydin.com. I have VPS running CentOS 5.7 with Plesk installed. By means of an vhost.conf and vhost_ssl.conf file I, (with the help of another gentleman) have managed to reverse proxy the app. vhost.conf: ServerName diaspora.mattaydin.com ServerAlias *.diaspora.mattaydin.com <Directory /home/diaspora/diaspora/public> Options -Includes -ExecCGI </Directory> DocumentRoot /home/diaspora/diaspora/public RedirectPermanent / https://diaspora.mattaydin.com vhost_ssl.conf ServerName diaspora.mattaydin.com DocumentRoot /home/diaspora/diaspora/public RewriteEngine On RewriteCond %{DOCUMENT_ROOT}/%{REQUEST_FILENAME} !-f RewriteRule ^/(.*)$ balancer://upstream%{REQUEST_URI} [P,QSA,L] <Proxy balancer://upstream> BalancerMember http://127.0.0.1:3000/ </Proxy> ProxyRequests Off ProxyVia On ProxyPreserveHost On RequestHeader set X_FORWARDED_PROTO https <Proxy *> Order allow,deny Allow from all </Proxy> <Directory /home/diaspora/diaspora/public> Options -Includes -ExecCGI Allow from all AllowOverride all Options +Indexes </Directory> DocumentRoot /home/diaspora/diaspora/public Basically it's working. However, the only thing that's not working are the assets. The do not get loaded not the server, as seen on diaspora.mattaydin.com The error messages I get in the access_ssl.log are a lot of: 11/Dec/2012:19:04:05 +0100] "GET /robots.txt HTTP/1.1" 404 2811 "-" "Mozilla/5.0 (Macintosh; Intel Mac OS X 10_8_2) AppleWebKit/536.26.17 (KHTML, like Gecko) Version/6.0.2 Safari/536.26.17" The error messages I get from diaspora's log file is: Started GET "//assets/branding/logo_large.png" for 77.250.99.193 at 2012-12-11 20:13:11 +0100 ActionController::RoutingError (No route matches [GET] "/assets/branding/logo_large.png"): lib/rack/chrome_frame.rb:39:in call' lib/unicorn_killer.rb:35:incall' Hope you guys can help me out. If you need anything else please let me know Thanks in advance, Matt

  Read the article

• Mounting an attached ebs volume in EC2

  - by David

  I've created an EC2 instance, created an EBS volume, attached it to the running instance, and successfully ssh'ed into my instance. The drive is attached as /dev/sdf Next, I tried mounting the drive by running: mkdir /testName mount -t ext3 /dev/sdf /testName But then I get the error message: mount: wrong fs type, bad option, bad superblock on /dev/sdf, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so What am I doing wrong? Thanks.

  Read the article

• filesystem mounting problem

  - by user306988

  Hello, A DAS box is attached to my linux box using LSI SCSI HBA. Volume is properly detected on the linux box and filesystem is created using mkfs.ext2 /dev/sdc #No partition table I can not mount the volume using mount/dev/sdc /mnt/temp -t ext3 But I can mount it using mount /dev/sdc /mnt/temp -t ext3 -o loop Can anybody please tell me what "-o loop" option does internally? Has anybody faced this option before? Thanks in advance, prashant

  Read the article

• Xen DomU on DRBD device: barrier errors

  - by Halfgaar

  I'm testing setting up a Xen DomU with a DRBD storage for easy failover. Most of the time, immediatly after booting the DomU, I get an IO error: [ 3.153370] EXT3-fs (xvda2): using internal journal [ 3.277115] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.336014] nf_conntrack version 0.5.0 (3899 buckets, 15596 max) [ 3.515604] init: failsafe main process (397) killed by TERM signal [ 3.801589] blkfront: barrier: write xvda2 op failed [ 3.801597] blkfront: xvda2: barrier or flush: disabled [ 3.801611] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801630] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801642] Buffer I/O error on device xvda2, logical block 6521396 [ 3.801652] lost page write due to I/O error on xvda2 [ 3.801755] Aborting journal on device xvda2. [ 3.804415] EXT3-fs (xvda2): error: ext3_journal_start_sb: Detected aborted journal [ 3.804434] EXT3-fs (xvda2): error: remounting filesystem read-only [ 3.814754] journal commit I/O error [ 6.973831] init: udev-fallback-graphics main process (538) terminated with status 1 [ 6.992267] init: plymouth-splash main process (546) terminated with status 1 The manpage of drbdsetup says that LVM (which I use) doesn't support barriers (better known as tagged command queuing or native command queing), so I configured the drbd device not to use barriers. This can be seen in /proc/drbd (by "wo:f, meaning flush, the next method drbd chooses after barrier): 3: cs:Connected ro:Primary/Secondary ds:UpToDate/UpToDate C r---- ns:2160152 nr:520204 dw:2680344 dr:2678107 al:3549 bm:9183 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 And on the other host: 3: cs:Connected ro:Secondary/Primary ds:UpToDate/UpToDate C r---- ns:0 nr:2160152 dw:2160152 dr:0 al:0 bm:8052 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 I also enabled the option disable_sendpage, as per the drbd docs: cat /sys/module/drbd/parameters/disable_sendpage Y I also tried adding barriers=0 to fstab as mount option. Still it sometimes says: [ 58.603896] blkfront: barrier: write xvda2 op failed [ 58.603903] blkfront: xvda2: barrier or flush: disabled I don't even know if ext3 has a nobarrier option. And, because only one of my storage systems is battery backed, it would not be smart anyway. Why does it still compain about barriers when I disabled that? Both host are: Debian: 6.0.4 uname -a: Linux 2.6.32-5-xen-amd64 drbd: 8.3.7 Xen: 4.0.1 Guest: Ubuntu 12.04 LTS uname -a: Linux 3.2.0-24-generic pvops drbd resource: resource drbdvm { meta-disk internal; device /dev/drbd3; startup { # The timeout value when the last known state of the other side was available. 0 means infinite. wfc-timeout 0; # Timeout value when the last known state was disconnected. 0 means infinite. degr-wfc-timeout 180; } syncer { # This is recommended only for low-bandwidth lines, to only send those # blocks which really have changed. #csums-alg md5; # Set to about half your net speed rate 60M; # It seems that this option moved to the 'net' section in drbd 8.4. (later release than Debian has currently) verify-alg md5; } net { # The manpage says this is recommended only in pre-production (because of its performance), to determine # if your LAN card has a TCP checksum offloading bug. #data-integrity-alg md5; } disk { # Detach causes the device to work over-the-network-only after the # underlying disk fails. Detach is not default for historical reasons, but is # recommended by the docs. # However, the Debian defaults in drbd.conf suggest the machine will reboot in that event... on-io-error detach; # LVM doesn't support barriers, so disabling it. It will revert to flush. Check wo: in /proc/drbd. If you don't disable it, you get IO errors. no-disk-barrier; } on host1 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.1:7792; } on host2 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.2:7792; } } DomU cfg: bootloader = '/usr/lib/xen-default/bin/pygrub' vcpus = '2' memory = '512' # # Disk device(s). # root = '/dev/xvda2 ro' disk = [ 'phy:/dev/drbd3,xvda2,w', 'phy:/dev/universe/drbdvm-swap,xvda1,w', ] # # Hostname # name = 'drbdvm' # # Networking # # fake IP for posting vif = [ 'ip=1.2.3.4,mac=00:16:3E:22:A8:A7' ] # # Behaviour # on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' In my test setup: the primary host's storage is 9650SE SATA-II RAID PCIe with battery. The secondary is software RAID1. Isn't DRBD+Xen widely used? With these problems, it's not going to work.

  Read the article

• Nginx Not Passing URL Parameters

  - by jmccartie

  Messing around with Nginx ... for some reason, it looks like none of my URL parameters are being passed. My homepage loads fine, but a URL like "http://mysite.com/more.php?id=101" throws errors, saying that the ID is an undefined index. I'm assuming this is something basic I'm missing in a conf file. Some info: conf.d/virtual.conf server { listen 80; server_name dev.mysite.com; index index.php; root /var/www/dev.mysite.com_html; location / { root /var/www/dev.mysite.com_html; } location ~ \.php(.*)$ { fastcgi_pass 127.0.0.1:9000; fastcgi_param SCRIPT_FILENAME /var/www/wap/dev.mysite.com_html/$fastcgi_script_n ame; fastcgi_index index.php; include /etc/nginx/fastcgi_params; } } Error log: 2009/06/22 11:44:21 [notice] 16319#0: start worker process 16322 2009/06/22 11:44:28 [error] 16320#0: *1 FastCGI sent in stderr: "PHP Notice: Undefined index: id in /var/www/dev.mysite.com_html/more.php on line 10 Thanks in advance.

  Read the article

• My linux server takes more than an hour to boot. Suggestions?

  - by jamieb

  I am building a CentOS 5.4 system that boots off a compact flash card using a card reader that emulates an IDE drive. It literally takes about an hour to boot. The ultra-slow part occurs when Grub is loading the kernel. Once that's done, the rest of the boot process only takes about a minute to get to a login prompt. Does anyone have any suggestions? I suspect that it may have to do with UDMA. Everything IDE-related in my BIOS seems to checkout. The read performance hdparm is telling me 1.77 MB/s. Ouch! (But even at that rate, it still shouldn't take an hour to decompress and load the kernel) [root@server ~]# hdparm -tT /dev/hdc /dev/hdc: Timing cached reads: 2444 MB in 2.00 seconds = 1222.04 MB/sec Timing buffered disk reads: 6 MB in 3.39 seconds = 1.77 MB/sec Trying to enable DMA is a no-go though: [root@server ~]# hdparm -d1 /dev/hdc /dev/hdc: setting using_dma to 1 (on) HDIO_SET_DMA failed: Operation not permitted using_dma = 0 (off) Here's some command outputs that might help: System [root@server ~]# uname -a Linux server.localdomain 2.6.18-164.el5xen #1 SMP Thu Sep 3 04:47:32 EDT 2009 i686 i686 i386 GNU/Linux PCI info: [root@server ~]# lspci -v 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) Subsystem: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub Flags: bus master, fast devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Intel Corporation 82945G/GZ Integrated Graphics Controller Flags: bus master, fast devsel, latency 0, IRQ 10 Memory at fdf00000 (32-bit, non-prefetchable) [size=512K] I/O ports at ff00 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fdf80000 (32-bit, non-prefetchable) [size=256K] Capabilities: [90] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Capabilities: [d0] Power Management version 2 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 Flags: bus master, medium devsel, latency 0, IRQ 16 I/O ports at fe00 [size=32] 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 Flags: bus master, medium devsel, latency 0, IRQ 17 I/O ports at fd00 [size=32] 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 Flags: bus master, medium devsel, latency 0, IRQ 18 I/O ports at fc00 [size=32] 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) (prog-if 00 [UHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 Flags: bus master, medium devsel, latency 0, IRQ 19 I/O ports at fb00 [size=32] 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) (prog-if 20 [EHCI]) Subsystem: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller Flags: bus master, medium devsel, latency 0, IRQ 16 Memory at fdfff000 (32-bit, non-prefetchable) [size=1K] Capabilities: [50] Power Management version 2 Capabilities: [58] Debug port 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) (prog-if 01 [Subtractive decode]) Flags: bus master, fast devsel, latency 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=32 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fde00000-fdefffff Prefetchable memory behind bridge: 00000000fdd00000-00000000fdd00000 Capabilities: [50] #0d [0000] 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) Subsystem: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge Flags: bus master, medium devsel, latency 0 Capabilities: [e0] Vendor Specific Information 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) (prog-if 80 [Master]) Subsystem: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 17 I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at <unassigned> I/O ports at f800 [size=16] Capabilities: [70] Power Management version 2 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) Subsystem: Intel Corporation 82801G (ICH7 Family) SMBus Controller Flags: medium devsel, IRQ 17 I/O ports at 0500 [size=32] 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 18 I/O ports at de00 [size=256] Memory at fdeff000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 17 I/O ports at dc00 [size=256] Memory at fdefe000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ Flags: bus master, medium devsel, latency 32, IRQ 19 I/O ports at da00 [size=256] Memory at fdefd000 (32-bit, non-prefetchable) [size=256] Capabilities: [50] Power Management version 2 hdparm ouput: [root@server ~]# hdparm /dev/hdc /dev/hdc: multcount = 0 (off) IO_support = 0 (default 16-bit) unmaskirq = 0 (off) using_dma = 0 (off) keepsettings = 0 (off) readonly = 0 (off) readahead = 256 (on) geometry = 8146/16/63, sectors = 8211168, start = 0 [root@server ~]# hdparm -I /dev/hdc /dev/hdc: ATA device, with non-removable media Model Number: InnoDisk Corp. - iCF4000 4GB Serial Number: 20091023AACA70000753 Firmware Revision: 081107 Standards: Supported: 5 Likely used: 6 Configuration: Logical max current cylinders 8146 8146 heads 16 16 sectors/track 63 63 -- CHS current addressable sectors: 8211168 LBA user addressable sectors: 8211168 device size with M = 1024*1024: 4009 MBytes device size with M = 1000*1000: 4204 MBytes (4 GB) Capabilities: LBA, IORDY(can be disabled) Standby timer values: spec'd by Vendor R/W multiple sector transfer: Max = 2 Current = 2 DMA: mdma0 mdma1 mdma2 udma0 udma1 *udma2 udma3 udma4 Cycle time: min=120ns recommended=120ns PIO: pio0 pio1 pio2 pio3 pio4 Cycle time: no flow control=120ns IORDY flow control=120ns Commands/features: Enabled Supported: * Power Management feature set * WRITE_BUFFER command * READ_BUFFER command * NOP cmd * CFA feature set * Mandatory FLUSH_CACHE HW reset results: CBLID- above Vih Device num = 0 CFA power mode 1: enabled and required by some commands Maximum current = 100ma Checksum: correct

  Read the article

• How to restrict user to a particular folder in CentOS 6?

  - by Chris Demetriad

  I will need to create users so developers can log in and clone/pull/push changes/repositories from a github like platform. I've managed to add a user (using the root) to this CentOS machine; I now have this line in /etc/passwd: chris:x:32008:32010::/home/chris/public_html:/bin/bash ..and this in /etc/shadow: chris:$1$ruUeLtTu$onAY2hdu1J.UmHajEIlmR.:15385:0:99999:7::: I am able to SSH the server, I have permission to create a folder and I guess that should be enough. But I am able to see other files and folders outside public_html. How can I actually restrict the user to a particular directory so he can't "cd out" of his folder? Update: root@echo [~]# ls -ld /home/moove drwx--x--x 21 moove moove 4096 Mar 22 16:16 /home/moove/ root@echo [~]# ls -ld /home/moove/public_html drwxr-x--- 11 moove nobody 4096 Mar 27 11:29 /home/moove/public_html/ root@echo [~]# ls -ld /home/moove/public_html/dev drwxr-x--- 12 moove nobody 4096 Mar 27 14:47 /home/moove/public_html/dev/ root@echo [~]# ls -ld /home/moove/public_html/dev/arsenal drwxr-xr-x 3 arsenal moove 4096 Mar 27 14:53 /home/moove/public_html/dev/arsenal/

  Read the article

• MediaWiki migrated from Tiger to Snow Leopard throwing an exceptions

  - by Matt S

  I had an old laptop running Mac OS X 10.4 with macports for web development: Apache 2, PHP 5.3.2, Mysql 5, etc. I got a new laptop running Mac OS X 10.6 and installed macports. I installed the same web development apps: Apache 2, PHP 5.3.2, Mysql 5, etc. All versions the same as my old laptop. A Mediawiki site (version 1.15) was copied over from my old system (via the Migration Assistant). Having a fresh Mysql setup, I dumped my old database and imported it on the new system. When I try to browse to mediawiki's "Special" pages, I get the following exception thrown: Invalid language code requested Backtrace: #0 /languages/Language.php(2539): Language::loadLocalisation(NULL) #1 /includes/MessageCache.php(846): Language::getFallbackFor(NULL) #2 /includes/MessageCache.php(821): MessageCache->processMessagesArray(Array, NULL) #3 /includes/GlobalFunctions.php(2901): MessageCache->loadMessagesFile('/Users/matt/Sit...', false) #4 /extensions/OpenID/OpenID.setup.php(181): wfLoadExtensionMessages('OpenID') #5 [internal function]: OpenIDLocalizedPageName(Array, 'en') #6 /includes/Hooks.php(117): call_user_func_array('OpenIDLocalized...', Array) #7 /languages/Language.php(1851): wfRunHooks('LanguageGetSpec...', Array) #8 /includes/SpecialPage.php(240): Language->getSpecialPageAliases() #9 /includes/SpecialPage.php(262): SpecialPage::initAliasList() #10 /includes/SpecialPage.php(406): SpecialPage::resolveAlias('UserLogin') #11 /includes/SpecialPage.php(507): SpecialPage::getPageByAlias('UserLogin') #12 /includes/Wiki.php(229): SpecialPage::executePath(Object(Title)) #13 /includes/Wiki.php(59): MediaWiki->initializeSpecialCases(Object(Title), Object(OutputPage), Object(WebRequest)) #14 /index.php(116): MediaWiki->initialize(Object(Title), NULL, Object(OutputPage), Object(User), Object(WebRequest)) #15 {main} I tried to step through Mediawiki's code, but it's a mess. There are global variables everywhere. If I change the code slightly to get around the exception, the page comes up blank and there are no errors (implying there are multiple problems). Anyone else get Mediawiki 1.15 working on OS X 10.6 with macports? Anything in the migration from Tiger that could cause a problem? Any clues where to look for answers?

  Read the article

< Previous Page | 66 67 68 69 70 71 72 73 74 75 76 77  | Next Page >