Search Results

Search found 2630 results on 106 pages for 'abood mount'.

Page 71/106 | < Previous Page | 67 68 69 70 71 72 73 74 75 76 77 78  | Next Page >

• UNR Installation: Partitioning Error

  - by Wesley

  Hi all, I have a Samsung N120 netbook (with upgraded 2GB RAM). I'm trying to install Ubuntu Netbook Remix, but when I set my partitions, I get an error. The setup I want right now is: Recovery Partition - 6 GB Windows XP Home Partition - 40 GB General Partition - remaining space UNR Partition - 40 GB I am told that I need to resize a partition and it will take a while. However, when it nearly starts, I get an ERROR!!! dialog that says, "Error informing the kernel about modifications to partition /dev/sda5 - Device or resource busy. This means Linux won't know about any changes you made to /dev/sda5 so you shouldn't mount it or use it in any way before rebooting." I'm not too sure what I should do right now... any ideas? Thanks in advance.

  Read the article

• growing EBS RAID volume

  - by Ryan Fernandes

  I've created a RAID0 configuration with two 1GB EBS volumes, mounted at /dev/md0 using mdadm and formatted with XFS Next, I copied some files over to fill the volume to around 30% of its capacity (of 2GB) I then created snapshots of the volumes using ec2-consistent-snapshot and created volumes of the said snapshots but specified the volume size to be 2GB (effective doubling the capacity on each disk) I then spun up a new instance, assembled the RAID0 configuration on /dev/md0 from the 2 volumes mentioned above and mount it to /vol df -hT showed /vol as 2GB (as expected) Now I ran sudo xfs_growfs -d /vol. The command completed normally but reported blocks changed from 523776 to 524160 (only!) and df -hT still showed /vol as 2GB (instead of the expected 4GB) I rebooted, remounted, reassembled the RAID but it still reports the old size. Any clue as to what went wrong?

  Read the article

• can I bundle multiple installs for Mac OSX and do them as a single script?

  - by Dov

  I have a lot of open source software to be installed for a course. We currently run on PCs that we provide. If we allow students to use their own Macs in Mac-centric schools, that means we have to load the software on those Macs. Rathern than have to load individual software, is there any way I can create a single file, mount it and run a script to install all packages? We are willing to simplify the installs by standardizing the locations to store the applications, since the students will have identical machines.

  Read the article

• NFS and KVM. Slow Speed

  - by Javier Martinez

  I have a KVM virtualization in Debian with 2 guests (Debian and Windows 2008). I want to have a 'mount point' shared that can be accessed by the 3 system (host and 2 guests) at the same time. So the only thing that I found was a NFS/SMB network storage. I picked NFS Due to my Ethernet network (10/100), the speed average that I get between accessing/transfering files between the 3 system is always 8~10MB/s. The point is if is there any chance of get a boost system for sharing files between 3 system (at the same time) without wasting the speed of my SATA disks. I mean, without the Ethernet limitation of 10 MB/s

  Read the article

• OpenVPN DNS: VPN DNS stomping local VPN

  - by Eddie Parker

  I've finally noodled with OpenVPN enough to get it working. Even better, I can mount samba drives, ping network machines through the TUN device, etc - it's all great. However, I'm noticing that if I use the following directive, then some of the machines that are normally visible by the client, on the client's side (i.e., not through the VPN) get masked with some other server out on the Internet. push "dhcp-option DNS 10.0.1.1" # Push our local DNS to clients Is there any way to avoid this, besides hacking the 'hosts' file on the client machine? Ideally I'd like to only use my VPN's DNS for machines within that domain.

  Read the article

• Can I have different ESX hosts accessing the same LUN over different protocols?

  - by Kevin Kuphal

  I currently have a cluster of two ESX 3.5U2 servers connected directly via FiberChannel to a NetApp 3020 cluster. These hosts mount four VMFS LUNs for virtual machine storage. Currently these LUNs are only made available via our FiberChannel initator in the Netapp configuration If I were to add an ESXi host to the cluster for internal IT use can I: Make the same VMFS LUNs available via the iSCSI initiator on the Netapp Connect this ESXi host to those LUNs via iSCSI Do all of this while the existing two ESX hosts are connected to those LUNs via FiberChannel Does anyone have experience with this type of mixed protocol environment, specifically with Netapp?

  Read the article

• Must partprobe before using drive?

  - by Jeff Welling

  This is a followup question to Cannot mount /dev/sdc1 on Debian 5.0, special device /dev/sdc1 doesn't exist Basically, I have 6 SATA hard drives in a machine and I'm trying to create a RAID6 array with them. When I try to run the mdadm command to create (with the verbose option) a raid array, I see messages like "mdadm: super1.x cannot open /dev/sdf1: No such device or address" which are resolved by doing partprobe /dev/sdf and then re-running the mdadm command. The problem is that I have to run partprobe after each reboot, and from experience I don't think this is normal behaviour -- on no other linux machine do I have to partprobe the device before I can use it. Something must be going wrong, but how do I troubleshoot this to find out what? Could this be caused by a hardware problem? Edit: Additional note - before I seemed to only have this problem with one drive, but now I'm having it with 3 drives.

  Read the article

• How to move linux executables to a ramdisk?

  - by alfa64

  i've made a ramdisk this way: mkdir -p /media/ramdisk mount -t tmpfs -o size=512M tmpfs /media/ramdisk/ The reason for this is because i run a lot of node.js scripts and their execution time is very small, but i suspect that the time overhead is because it reloads the node.js executable from disk and destroys it on each subsecuent run. So i think this might be the solution to gain a bit, if not much, performance. How can i move a program like node to the ramdisk and run it from there? The idea is to have a startup script that creates the ramdisk and puts the node files inside of it. Note that i'm currently using fedora 16 for what's it's worth. Thanks in advance.

  Read the article

• Kubuntu 9.10: LUKS-encrypt entire partition

  - by Adam Matan

  Hi, In older versions of Ubuntu, mainly 8.04, I could encrypt en entire partition using LUKS, and mount it as /. the /boot directory was mounted on another partition. At boot time, I had to enter my password to enable any access to anything other than /boot. In Kubuntu 9.10, I only have the option to encrypt my /home/adam directory, which is a bit of a problem for me because I have sensitive data located in other directories. Any ideas how to set up LUKS for the entire disk, preferably during installation? Thanks in advance, Adam

  Read the article

• Measuring accesses to files - apache

  - by George

  So, I run a website, that among other things serves some files (usually PDFs). All of these are stored under a specific directory on the server: /var/www/vhosts/mysite.com/httpdocs/site/pdf_files Due to storage issues on my VPS I am thinking of getting some S3 or other cloud storage, and mount it as a drive using S3QL/S3FS. Then I will be able to have the pdf_files folder symlinked to the cloud folder and serve those files using that, without any changes on the web app (is that a good plan?) Now, before doing that, to estimate costs, I need to measure how many file accesses people do, how many times those pdf files are downloaded each month for example. Basically how many times those pdf files are accessed through the webserver. I'd like to do it on the apache level. What's the best way that this can be done? e.g.: measuring the bandwidth used by files in that specific folder would also be nice, but estimating the GET requests I'll be doing to amazon is more important.

  Read the article

• Can't Remove Logical Drive/Array from HP P400

  - by Myles

  This is my first post here. Thank you in advance for any assistance with this matter. I'm trying to remove a logical drive (logical drive 2) and an array (array "B") from my Smart Array P400. The host is a DL580 G5 running 64-bit Red Hat Enterprise Linux Server release 5.7 (Tikanga). I am unable to remove the array using either hpacucli or cpqacuxe. I believe it is because of "OS Status: LOCKED". The file system that lives on this array has been unmounted. I do not want to reboot the host. Is there some way to "release" this logical drive so I can remove the array? Note that I do not need to preserve the data on logical drive 2. I intend to physically remove the drives from the machine and replace them with larger drives. I'm using the cciss kernel module that ships with Red Hat 5.7. Here is some information pertaining to the host and the P400 configuration: [root@gort ~]# cat /etc/redhat-release Red Hat Enterprise Linux Server release 5.7 (Tikanga) [root@gort ~]# uname -a Linux gort 2.6.18-274.el5 #1 SMP Fri Jul 8 17:36:59 EDT 2011 x86_64 x86_64 x86_64 GNU/Linux [root@gort ~]# rpm -qa | egrep '^(hp|cpq)' cpqacuxe-9.30-15.0 hp-health-9.25-1551.7.rhel5 hpsmh-7.1.2-3 hpdiags-9.3.0-466 hponcfg-3.1.0-0 hp-snmp-agents-9.25-2384.8.rhel5 hpacucli-9.30-15.0 [root@gort ~]# hpacucli HP Array Configuration Utility CLI 9.30.15.0 Detecting Controllers...Done. Type "help" for a list of supported commands. Type "exit" to close the console. => ctrl all show config detail Smart Array P400 in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Cache Serial Number: PA82C0J9SVW34U RAID 6 (ADG) Status: Enabled Controller Status: OK Hardware Revision: D Firmware Version: 7.22 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 15 secs Surface Scan Mode: Idle Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 0 secs Cache Board Present: True Cache Status: OK Cache Ratio: 25% Read / 75% Write Drive Write Cache: Disabled Total Cache Size: 256 MB Total Cache Memory Available: 208 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Logical Drive: 1 Size: 136.7 GB Fault Tolerance: RAID 1 Heads: 255 Sectors Per Track: 32 Cylinders: 35132 Strip Size: 128 KB Full Stripe Size: 128 KB Status: OK Caching: Enabled Unique Identifier: 600508B100184A395356573334550002 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 101 MB, /tmp 7.8 GB, /usr 3.9 GB, /usr/local 2.0 GB, /var 3.9 GB, / 2.0 GB, /local 113.2 GB OS Status: LOCKED Logical Drive Label: A0027AA78DEE Mirror Group 0: physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) Drive Type: Data Array: A Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:1 Port: 1I Box: 1 Bay: 1 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM57RF40000983878FX Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 35 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 1I:1:2 Port: 1I Box: 1 Bay: 2 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM55VQC000098388524 Model: HP DG146BB976 Current Temperature (C): 29 Maximum Temperature (C): 36 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown Logical Drive: 2 Size: 546.8 GB Fault Tolerance: RAID 5 Heads: 255 Sectors Per Track: 32 Cylinders: 65535 Strip Size: 64 KB Full Stripe Size: 256 KB Status: OK Caching: Enabled Parity Initialization Status: Initialization Completed Unique Identifier: 600508B100184A395356573334550003 Disk Name: /dev/cciss/c0d1 Mount Points: None OS Status: LOCKED Logical Drive Label: A5C9C6F81504 Drive Type: Data Array: B Interface Type: SAS Unused Space: 0 MB Status: OK Array Type: Data physicaldrive 1I:1:3 Port: 1I Box: 1 Bay: 3 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2H5PE00009802NK19 Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 37 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 1I:1:4 Port: 1I Box: 1 Bay: 4 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM28YY400009750MKPJ Model: HP DG146ABAB4 Current Temperature (C): 31 Maximum Temperature (C): 36 PHY Count: 1 PHY Transfer Rate: 3.0Gbps physicaldrive 2I:1:5 Port: 2I Box: 1 Bay: 5 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FGYV00009802N3GN Model: HP DG146ABAB4 Current Temperature (C): 30 Maximum Temperature (C): 38 PHY Count: 1 PHY Transfer Rate: Unknown physicaldrive 2I:1:6 Port: 2I Box: 1 Bay: 6 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM8AFAK00009920MMV1 Model: HP DG146BB976 Current Temperature (C): 31 Maximum Temperature (C): 41 PHY Count: 2 PHY Transfer Rate: Unknown, Unknown physicaldrive 2I:1:7 Port: 2I Box: 1 Bay: 7 Status: OK Drive Type: Data Drive Interface Type: SAS Size: 146 GB Rotational Speed: 10000 Firmware Revision: HPDE Serial Number: 3NM2FJQD00009801MSHQ Model: HP DG146ABAB4 Current Temperature (C): 29 Maximum Temperature (C): 39 PHY Count: 1 PHY Transfer Rate: Unknown

  Read the article

• Error "fileid changed" when accessing files over NFS

  - by Roman Prikhodchenko

  I have an nfs-kernel-server configured and running on Ubuntu 10.04 Server. /export THIRD_SERVER_IP(rw,fsid=0,insecure,no_subtree_check,async) SECOND_SERVER_IP(rw,fsid=0,insecure,no_subtree_check,async) /export/ebs THIRD_SERVER_IP(rw,fsid=0,insecure,no_subtree_check,async) SECOND_SERVER_IP(rw,nohide,insecure,no_subtree_check,async) I mounted the exported folder to the second server: mount -t nfs4 -o proto=tcp,port=2049 NFS_SERVER_IP_HERE:/ebs /ebs and it works just fine. I mounted it to the third server but I cannot access files from it. ls -l /ebs ls: reading directory /ebs: Stale NFS file handle total 0 The syslog on the third server says: kernel: [11575.483720] NFS: server NFS_SERVER_IP_HERE error: fileid changed kernel: [11575.483722] fsid 0:14: expected fileid 0x2, got 0x6e001 Some info: uname -r 2.6.32-312-ec2 uname -m i686

  Read the article

• Read Linux-formatted (ext3) EBS volume mounted on Windows Server 2008 instance

  - by Greg Owen

  I've got a Windows Server 2008 R2 instance set up in Amazon EC2. I've also got some Ubuntu instances on the same EC2 account. I'd like to be able to mount the EBS volume from one of the Ubuntu instances onto the Windows instance as an external drive and then access that drive from the Windows instance. I've looked at tools like ext2fsd and ext2 IFS, but these haven't worked (I couldn't get the former to work, and the latter says that it supports Windows 2008 but gives an error when I try to install it, saying that it only supports up to Windows 2003). I know that there are all kinds of tools to view Linux partitions and that there are filesystems that are compatible with both Linux and Windows, but neither of those options works here (I want to be able to attach and detach the Ubuntu volumes on command, rather than have a permanent partition, and Ubuntu EBS volumes are ext3 by default). Anybody know a good tool I should use?

  Read the article

• Rails won't install on Ubuntu because of builder

  - by Jason Swett

  Can someone explain why gem thinks I don't have builder = 2.1.2 even though I clearly have 3.0.0? jason@ve:~$ gem install rails --pre ERROR: Error installing rails: activemodel requires builder (~> 2.1.2, runtime) jason@ve:~$ gem list *** LOCAL GEMS *** abstract (1.0.0) activesupport (3.0.3, 3.0.0.rc2) builder (3.0.0) erubis (2.6.6) i18n (0.5.0) mail (2.2.13) memcache-client (1.8.5) mime-types (1.16) polyglot (0.3.1) rack (1.2.1) rack-mount (0.6.13) rack-test (0.5.6) text-format (1.0.0) text-hyphen (1.0.0) treetop (1.4.9) tzinfo (0.3.23) jason@ve:~$

  Read the article

• Why should I use cobbler over normal PXEBOOT server?

  - by luckytaxi

  Maybe it's me but I find it easier to manage my simple pxeboot server just by editing the default file under /tftpboot/pxelinux.cfg. I have my kickstart file available over NFS along with the DVD extracted to a centralize mount point. Other than PXEBOOT, what benefit would I get from running cobbler? It was confusing at first but I finally got the hang off it. The only benefit I see is being able to force a server to install an OS on demand. Anything else?

  Read the article

• Rack Equipment that is Non-Integer Rack Units Tall

  - by alx9r

  I came across these two items of non-integer rack unit height: 1. This rack mount kit which seems to be trying to make the best of the slightly-taller-than-1U form factor of the Cisco ASA5505. 2. This 1.5U Server Case that espouses the merits of a case height between 1RU and 2RU. My questions are as follows: A. (1) seems to protrude 1/8 RU above and below the rack unit it is bolted in. Is there any way to make use of the 7/8 RU remaining above and below? Or would using that bracket effectively consume 3 RU? B. Are there any gotchas I should be aware of (like rack rail bolt patterns not working out, etc) when I consider one of these non-integer RU server cases like (2)?

  Read the article

• Windows XP-64 loses audio sounds, drive letters... why?

  - by Ira Baxter

  Until sometime in early December, I had a wonderfully functioning XP-64 system. It was configured to auto download/install MS patches. I occassionally update the software on it, e.g. Open Office, Adobe Reader, Skype, but I don't fetch hundreds of tools or anything much beyond what I just mentioned. In December, suddenly my audio stopped, and drive letters assigned to various mount points on other machines quit being available. Apparantly, the services that support these (and some others) are now not starting up when I boot/login. There isn't anything obvious in the event log. If I manually restart the associated services, these facilities come back on line and work for awhile (a day) but pretty soon the problem reappears. I don't reboot very often, nor do I log out out much. Hints?

  Read the article

• Recovering with DDRescue Cannot Complete (write error: Read-only file system)

  - by c00lryguy

  I'm trying to recover a corrupt VDI using vdfuse to mount the VDI and using dd_rescue to rescue the borked partition. dd_rescue seems to be working fine but once it reached about half of the partition, it just STOPs and gives the following error: ddrescue: write error: Read-only file system Wait.. what? It suddenly turns the FS it is writing the recovered partition to into a read-only file system. Well... why? Will I never be able to finish this? What's going on?

  Read the article

• Oracle on NFS vmdk beats native NFS!?

  - by fletch00

  Hi, my colleagues are pursuing this with Netapp and Oracle - but I thought I'd post here on the off chance someone else has seen this We have a RedHat 5 VM (fully up2date) running Oracle 11i with data disks mounted via the VM's linux kernel NFS using Oracle's recommended mount options and the performance is very inconsistent (Querys that should take < 2 seconds sometimes take 60 seconds) Funny thing is we can run the same queries perfectly consistently < 2 seconds on a VMDK residing on SAME NetApp NFS datastore! Makes me wish Oracle and NetApp collaborated as closely as VMware and NetApp did on the Virtual Storage Console we used to perfectly set the NFS options and keep them in compliance... We have tried a few Linux NFS options others have posted and not seen improvement so far. We are now creating VMDK's for the VM to replace the Linux NFS mounted and workaround the issue as our developers need consistent performance ASAP.

  Read the article

• Installing Fedora 11 fIlesystem from ISO in to a VM image

  - by okhalid

  Hi, I need to install Fedora 11 in my monitor-less linux box which is running some where in a data center. I will use Fedora 11 as a virtual machine. What I already know/have: 1) How to create LVM partitions and create ext3 filesystem 2) Mount the LVM partition and ISO image 3) Run the partition with Xen as a virtual machine What I need: 1) I need to install Fedora ll file system into an lvm partition (let's say /dev/fedora11) from an ISO image so that I have all the directories /root, /bin, /sys etc etc under /dev/fedora11 Any help would be much appreciated! NOTE: I don't have a monitor for this server, so I need to do it via SSH

  Read the article

• moving dynamic disk from Windows to another Windows computer when original Windows is not available

  - by Andrei

  How do I mount dynamic disk on new system without access to the old OS ? I need to move Dynamic data disk from old Windows XP (Pro, SP3) system, where disk crashed, to new Windows system without having access to the old OS. On new system, Dynamic disk shows as "Dynamic - Foreign". Microfoft has instructions for moving Dynamic Disk [1]. But Microsoft assumes having access to the old system. But I do not have acess to the old system. I am struck with "Dynamic - Foreign" static of the disk on new system. Thanks WinXP Pro SP3 [1] http://technet.microsoft.com/en-us/library/cc779854(WS.10).aspx Move Disk to another computer.

  Read the article

• Windows 2008 and Truecrypt: can't access shared folder called "media"

  - by Sajee

  On my Windows 2008 system, I've attached an external USB drive that's encrypted using Truecrypt. Once I mounted the Truecrypt drive, I share some of the directories from that drive using Windows file sharing. I tried sharing a folder called "media" and when I try to access that folder from a Vista client on my LAN via \myserver\media, I get this error: \myserver\media is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. An unexpected network error occurred. If I share the folder media under some name such as fizzbuzz then I can access \myserver\fizzbuzz w/o any errors. Any clues as to why this is happening? Related: http://serverfault.com/questions/27684/windows-2008-and-truecrypt-how-to-automatically-mount-shared-folders-after-rest

  Read the article

• portable cross-platform WebDAV Client

  - by theduke

  I am looking for a portable application that will allow me to do this: Browse a WebDAV share and open a file. Edit the file locally. Save the file, and automatically propagate the change to WebDAV. Is there any CROSS-PLATFORM application out there that will let me do this and exists as a portable? The reason I need this functionality is that I regularily have to access files via WebDAV from public machines where I do not have the neccessary permissions to natively mount a webdav share, or to install the neccessary components.

  Read the article

• Wildcards not being substituted

  - by user21463

  #!/bin/bash loc=`echo ~/.gvfs/*/DCIM/100_FUJI` rm -f /mnt/fujifilmA100 ln -s "$loc" /mnt/fujifilmA100 For some reason the variable * doesn't get substituted with the only possible value and gets given the value /home/chris/.gvfs/*/DCIM/100_FUJI. Does anyone have an idea of why? Please note: If global expansion fails, the pattern is not substituted. I ran the commands: chris@comp2008:~$ loc=`echo ~/.gvfs/*/DCIM/100_FUJI ` chris@comp2008:~$ echo $loc /home/chris/.gvfs/gphoto2 mount on usb%3A001,008/DCIM/100_FUJI So we can see the expansion should work I have now switched to using: loc = `find ~/.gvfs -name 100_FUJI ` I am just curious why it doesn't work as is. Debugging output using sh -x echo /home/chris/.gvfs/*/DCIM/100_FUJI loc=/home/chris/.gvfs/*/DCIM/100_FUJI rm -f /mnt/fujifilmA100 ln -s /home/chris/.gvfs/*/DCIM/100_FUJI/mnt/fujifilmA100

  Read the article

• Slow NFS transfer performance of small files

  - by Arie K

  I'm using Openfiler 2.3 on an HP ML370 G5, Smart Array P400, SAS disks combined using RAID 1+0. I set up an NFS share from ext3 partition using Openfiler's web based configuration, and I succeeded to mount the share from another host. Both host are connected using dedicated gigabit link. Simple benchmark using dd: $ dd if=/dev/zero of=outfile bs=1000 count=2000000 2000000+0 records in 2000000+0 records out 2000000000 bytes (2.0 GB) copied, 34.4737 s, 58.0 MB/s I see it can achieve moderate transfer speed (58.0 MB/s). But if I copy a directory containing many small files (.php and .jpg, around 1-4 kB per file) of total size ~300 MB, the cp process ends in about 10 minutes. Is NFS not suitable for small file transfer like above case? Or is there some parameters that must be adjusted?

  Read the article

< Previous Page | 67 68 69 70 71 72 73 74 75 76 77 78  | Next Page >