Search Results

Search found 2692 results on 108 pages for 'ts gateway'.

Page 74/108 | < Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >

• Unable chage IP address for eth0 without restart in Ubunto

  - by Rodnower

  I have Ubuntu 12.04.1 installed. I try to change IP address of the interface eth0 in /etc/network/interfaces from 192.168.1.3 to 192.168.1.4: auto lo iface lo inet loopback pre-up iptables-restore < /etc/iptables.up.rules auto eth0 iface eth0 inet static address 192.168.1.4 gateway 192.168.1.1 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 sudo service networking status Now I issue: sudo service networking restart I have response: stop: Unknown instance: networking stop/waiting And IP remains 192.168.1.3: eth0 Link encap:Ethernet HWaddr 00:1e:33:71:cd:a4 inet addr:192.168.1.3 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21e:33ff:fe71:cda4/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3861 errors:0 dropped:0 overruns:0 frame:0 TX packets:3291 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3423285 (3.4 MB) TX bytes:521854 (521.8 KB) Interrupt:45 Base address:0x4000 Only after restart IP changing... Any ideas?

  Read the article

• Encrypting absolutely everything, even within the LAN

  - by chris_l

  Has anybody tried that approach already? I'm really considering it: Instead of relying on network based IDS etc., every packet must use encryption which was initiated by a certificate issued by my own CA. Every client gets a unique client certificate Every server gets a unique server certificate Every service additionally requires to login. Both SSL and SSH would be ok. Access to the internet would be done via an SSL tunnel to the gateway. Is it feasible? Does it create practical problems? How could it be done and enforced? What do you think?

  Read the article

• ssh can't connect after server ip changed

  - by Kery

  I have a server with ubuntu installed. After I change the network configuration and restart server, ssh client can't connect server any more. But in the server I can use ssh client to connect itself and the netstat command shows that sshd is listening port 22. And in my computer (win7) ping command is OK to server's new IP. The configuration in /etc/network/interfaces is: auto eth0 iface eth0 inet static address 10.80.x.x netmask 255.255.255.0 gateway 10.80.x.1 I'm very confused about this. Hope somebody can give me some idea. Thank you in advance!!!

  Read the article

• Trouble with Remote Desktop pulling through printers. Drive Redirection works, and the ports created but not the printers

  - by Windex

  I've run out of things to look into. All the support documents have been gone through and still provide no resolution. I've checked the service permissions, (sc sdshow spooler) they all match up with other systems and what is output on the support documents. I'm nearly positive that the issue can't be permissions anyway as the software requires all users to be an administrator, so all users are a local administrator. (I haven't looked into why yet but its on the list, I was just recently brought into this team and we've put procedures in place for quick recovery.) We've applied hot fixes relating to RDS and printing, though I'm not sure which ones they were. I've combed through group policy and no where is printer redirection disabled. It's setup with all default values regarding the use and redirection of printers and a quick install of W2k8 R2 shows that it works by default. This dev install was joined to the same domain, placed in the same OU, shows the same policies applied, etc, etc, etc, The server generates all the correct redirected ports but no printers are created. It will also redirect drives without issue, this would seem to rule out the usermode service that handles redirects being broken. No events are logged related to any of the events and there are no events from the TerminalServices-Printer source. There were local printers setup. I didn't think it would mattter but as I was running out of ideas I tried deleting them all with no change. The TS was configured for the software it will be running before we checked out the redirection of printers so the other team responsible to setting up new servers wants to find a fix instead of reloading a new server. I'm not sure where or what else to look for. Any ideas?

  Read the article

• Linux QoS (Skype / BitTorent / SIP / HTTP priority)

  - by Andre

  We are configuring a linux box that will act as internet gateway for an office of 30-50 computers. We are using iptables/HTB for traffic shaping. Is there a way to match traffic on L7 level? It's easy to identify traffic by TCP/UDP ports (like SIP and HTTP). But what if we are dealing with Skype & BitTorent? It was surprise for me that there is no powerful and matured sulution for tasks like this. I found only l7-filter (http://l7-filter.clearfoundation.com/) patch for the Linux kernel, but it's no longer supported (it seems to). Moreover it couldn't be compiled with modern Linux kernels. The only option I found was to use a Cisco router. Are there other ways to identify and shape Skype and Bittorent traffic?

  Read the article

• Ubuntu 11.04 Static IP doesn't take

  - by mrduclaw

  I'm trying to set a static IP address in Ubuntu 11.04. I did a server install. I edited my /etc/network/interfaces file to include: auto eth0 iface eth0 inet static address 10.0.0.100 netmask 255.255.255.0 gateway 10.0.0.1 When I do a /etc/init.d/networking restart this appears to take. After awhile though, that 10.0.0.100 will turn into something dished out by the DHCP server. My problem appears to be similar to this: Ubuntu intrepid - static IP networking keeps restarting with DHCP But I don't have Gnome installed. Is there anything else that's running in the background that could be doing this? And if so, how do I disable it?

  Read the article

• Bringing the xenbr0 interface up on XEN under Ubuntu 8.04

  - by iyl

  I installed XEN on Ubuntu 8.04 using this tutorial: http://www.howtoforge.com/ubuntu-8.04-server-install-xen-from-ubuntu-repositories but after I reboot with the XEN kernel, I don't have xenbr0 device. I see that network-bridge script runs and it creates peth0 device, but not xenbr0. I have a very basic IP setup, with a single static IP defined in /etc/network/interfaces. The only unusual thing is that my hosting (1&1) gave me a netmask 255.255.255.255, so I had to add the default gateway with this script: /sbin/route add -host 10.255.255.1 dev eth0 /sbin/route add default gw 10.255.255.1 Everything else is plain vanilla Ubuntu 8.04.

  Read the article

• Combine VPN bandwith over two or more WAN connections? Load balancing?

  - by mistrfu

  Imagine you only have DSL with 5mbps Down and 2mbps Up. Is it possible to have 10 of these for example and combine them in a way that would increase the upstrean bandwidth to one server? In my head it works like this: intranet with one gateway/router router connected to multi wan load ballancer on each ballancer wan port router with vpn clinet set up, tunneling to a server ?some? software on the server in cloud joining all these connection into one interface again I would need this mostly for big uploads to a server, downlink to the office is not that important at all. Does it even make sense? I drew an image to clarify.

  Read the article

• Setting up VMWare ESXi 5 with a single physical NIC

  - by deed02392

  I have a cheap but powerful dedicated server I am leasing with OVH, because they were recently having a promotion. I would like to try and manage all this power by playing with VMs using ESXi. However I am only provided with a single NIC. I had thought this would be easy to get around since, at home I have a single NIC which is my broadband modem, and yet a simple NAT gateway device happily provides internet access to all my devices. I am struggling to implement this on ESXi, though. Can anyone advise on how I could go about having ESXi and multiple VMs working with just one NIC? Here's my current setup: I believe all I need is to be able to configure NAT from the NIC to all the VMs etc.. How would I set up and administer this kind of infrastructure?

  Read the article

• How to setup a daily report of the top e-mail senders in Exchange 2010

  - by Belmin

  We have had issues with compromised Exchange accounts sending a large amount of unsolicited e-mails out. We have mitigated this by using a cloud e-mail gateway that does a better job in detecting these outgoing messages as to not hurt our e-mail reputation. However, we would still like to detect any abnormal e-mail activities. One idea is a report of the Exchange accounts with the most outgoing message. Any idea on how to do this? Or a similar stat that may be indicative of an account being compromised?

  Read the article

• Selectively routing traffic via ethernet or wifi, with proper DNS (Mac OS X 10.6)

  - by Dan

  When I'm at work, I access various intranet pages as well as the wider Internet through ethernet. However, the company LAN blocks some ports (e.g. Google Calendar). I can get to those through WiFi. So, I gave the Airport priority, and then using route add, I set up selective routing: all intranet traffic goes through the ethernet and everything else via WiFi: sudo route add 10.0.0.0/8 <intranet gateway>. However, there are a number of intranet sites that have their own DNS; i.e., hr.company.com only resolves on the intranet. The only way that I can get the DNS to work properly is to add the internal DNS server to the Airport DNS listing, however I fear that when I go elsewhere and forget, this will break things. What's the right way to get the DNS to resolve using this setup?

  Read the article

• how to communicate in typical router switch router scenario?

  - by Kossel

  I'm learning routing using packet tracer simulation and I think this is a very commun scenario: let's say pc4 is the server... why I can't ping from PC1 to 192.168.2.253 (router1) but I can ping 192.168.2.2 (pc0) aren't they the same subnet? what am I missing or have to do in order to reach pc4? (192.168.100.254) from pc 1 (192.168.1.1) is there something like "default gateway" for router? thanks for advice PS: during the simulation it shows error "The routing table does not have a route to the destination IP address. The router drops the packe (from 192.168.2.253 to 192.168.1.1)"

  Read the article

• How to make all of my IPs works in HyperVM XEN?

  - by user758667

  I've installed HyperVM on CentOS 5.8 final to make XEN VPS. I have 5 IPs, and added them to an IPPool. They are from *.123 to *.126. But when I add Virtual machines, just the first one (which indicate to *.123 ip) works well. I mean I can ssh to it by "works well" and when I want ssh to the other ones ( *.124 *.125 ...) it says : ssh: connect to host *.124 port 22: Connection timed out after a while. I alos set gateway and netmask as it shows in my server IPAdresses for device eth0 (it doesn't make any difference if I set these or not, I get same error). What should I do now? Thanks.

  Read the article

• IPSec VPN IP addresses

  - by Randomblue

  I have an IPSec VPN on my Windows 7 machine (all using the native Windows 7 gateway). The host I am connecting to has different ISAKMP "Phase 1" and "Phase 2" IP addresses. As I understand, the Phase 1 address is that of the IPsec endpoint, to which I can connect just fine. The Phase 2 address is found in their "crypto map", and the addresses need to match. At the moment, both my Phase 1 and Phase 2 addresses are configured the same. On my side, I get the error "Error 791: The L2TP connection attempt failed because security policy for the connection was not found" How can I configure the Phase 2 IP address for my Windows 7 IPSec VPN to be different to the IPSec endpoint address?

  Read the article

• Dynamic authentication realms in Apache

  - by Cogsy

  I have a front end server acting as a gateway proxy for many (a dynamic 'many') building monitors with embedded webservers. They are accessed with a URL like: http://www.example.com/monitor1/ http://www.example.com/monitor2/ ... I'm trying to restrict access to these monitors to only the users that own them. So what I need is a way of specifying rights to users or groups for specific directories. The standard auth mechanisms I see in Apache won't work because I need to specify every location. I'd prefer some dynamic map or script. Any suggestions?

  Read the article

• Unable to open websites that use HTTPS on linux

  - by negai

  I have the following network configuration: My PC 192.168.1.20/24 uses 192.168.1.1/24 as a gateway. Dlink-2760U router with Local address 192.168.1.1/24 has a VPN connection open with the provider using PPTP. Whenever I'm trying to open some web-sites that has some authorization (e.g. gmail.com, coursera.org), I'm getting a request timeout. This problem is observed mostly on linux (Ubuntu 12.04 and Debian 6.0), while most of such websites work correctly on windows XP. Could you please help me diagnose the problem? Could it be related to NAT + HTTPS? Thanks

  Read the article

• Change ip route metric

  - by notphunny

  I'm constantly switching between eth0 and wlan0 interface on my archlinux because I often change OpenWrt fw images on my second router (which isn't connected anywhere). So I have problem with my routes when I'm connected to my wlan and want to connect with Ethernet to my router. Both routers are on 192.168.1.1/24 and after connecting to my Ethernet profile eth0 route becomes default one (which is ok for the time), because of smaller metric I guess. So I'm interested, how can I change routes metric so my applications can be connected to the internet (through out wlan)? Maybe there is solution not to use Default Gateway on Ethernet profile, however I still want to know how to change metric. Or default route if there are more then one.

  Read the article

• Hosting company that does Linux VPS and MS SQL

  - by danielmcq

  I'm looking for hosted solutions but there are so many companies that finding the right one using a Google search is a bit overwhelming. Ideally I would like a hosting company which has following options: -Linux VPSs - Individual VPSs should be fairly cheap since I plan on putting one or two services per VPS i.e web server on one (httpd and ColdFusion), an SVN server on another, etc. -Managed MS SQL databases - My company already has data in MS SQL databases and a lot of ColdFusion code written that has MS SQL specific commands in it. -Individually purchased dedicated IP addresses -Preferably located in the North America region My plan would be to setup one Linux VPS as a gateway/firewall/VPN server and have all of my traffic routed through so that my other servers would not use of bandwidth by talking to each other. The trick is also finding a company that does Linux VPS AND MS SQL databases. Does anybody know of any hosting companies offer what I'm looking for? Let me know if I need to add more details.

  Read the article

• How failover should work in IIS cluster with Application Request Routing?

  - by username

  I have set up several servers with IIS and connected them to the load balancer - server with installed IIS Application Request Routing. I have created a server farm and added two servers. Then I stopped IIS on the first server and tried to open my web site. It returned me an error: 502 - Web server received an invalid response while acting as a gateway or proxy server. But if instead of stopping IIS I shut down the first server, I'm getting a response from the next server which is online. The question is, what the expected behaviour should be for failover with ARR, should it switch me to the next server if IIS is stopped and server is online?

  Read the article

• cannot using internet in VMWare

  - by user66247

  I am using VMware Workstation version 7 on Ubuntu 10.10. I installed Windows XP service pack 3 for guest os. Within VMWare, I am using bridge connection that I assigned static IP address to be able to ping host IP address but I cannot ping default router gateway. I also tried to command "/etc/init.d/vmware start" on terminal. All tasks are able to start successfully except "VM communication interface socket family" I am not sure that how to setup network for my VMWare by using wireless. Thanks in advance.

  Read the article

• Can't set up printer

  - by Jason Swett

  I'm trying to set up an HP OFficejet Pro 8500 A909a on my Windows XP machine over the network. I know the IP address of the printer but it's unclear to me how to set it up based on that. I have no idea how to troubleshoot this problem. I've tried installing the drivers but when I do that it tells me the printer is on a different gateway from my workstation, which is not true. Also, other people in the office are able to connect to this printer just fine, although the driver apparently didn't work for them, either.

  Read the article

• What is the best appliance you've used?

  - by phuzion

  Post your favorite appliances or "all-in-one" programs. Whether it runs in a virtual machine, or on its own hardware, it all goes. My submission is Untangle. It's an open source network gateway (their term). Essentially, it can run a plethora of things that you may otherwise end up buying another appliance for: Web filtering logging mail spam filtering phishing monitor spyware blocking VPN You name it, it's all there. Best of all, it's mostly free. A few appliances have annual costs due to inherent licensing or subscription costs. If you are looking for a new network perimeter device, definitely check it out. The underlying OS doesn't matter, because it's the application we want to praise, not the OS beneath it.

  Read the article

• Cisco WLAN Controller not pushing out DHCP addresses, what else could it be?

  - by Name

  On our Cisco WLAN Controller web interfaces, in Controller Interfaces, I have made a new interface with these settings: VLAN Identifier 202 IP Address 172.16.202.1 Netmask 255.255.255.0 Gateway 172.16.202.254 Primary DHCP Server 172.16.100.3 Secondary DHCP Server 172.16.100.2 Port: LAG I've also made a new WLAN and assigned it to the above interface. I have saved changes. But our wireless devices, although they seem to authenticate with the WLAN fine, they always get stuck on "obtaining DHCP address", so it seems the WLAN Controller isn't pushing out DHCP addresses to our devices. We do have a DHCP scope for the above in Windows Server 2008 R2 and everything there seems fine. If I connect a device with a static address (e.g. 172.16.202.10), it will connect. Stuck on what to do :(

  Read the article

• Cannot Ping PS3 Using a Wired Connection

  - by Post

  PS3 is using the inbuilt wireless network adapter (I cannot change this) When I try to ping the PS3 from ANY computer which is on a wired ethernet connection, I get Request Timed Out errors. Whenever I ping from a computer with a wireless connection, it works just fine. To be clear: Pinging from Wireless PC to Wireless PS3 works Pinging from Wired PC to Wireless PS3 fails I have tried this on several PC's and Laptops all with the same results. As an attempted solution I have set up static IP's on all related devices. More information: Default Gateway = 192.168.2.1 PS3(wireless) = 192.168.2.100 PC(wired) = 192.168.2.99 Subnet Mask(for both devices, I have made sure) = 255.255.255.0 Thanks

  Read the article

• Separate 2 networks with 1 Windows Server

  - by SamuGG

  The situation is: I have 1 router 192.168.1.1, 1 switch, 1 windows server and a basic LAN of devices accessing it. I need to split into 2 separate LANs with full Internet access each, but isolated from each other. Given that, the server is a Windows Server 2008 R2 with 2 NICs: NIC1: 192.168.1.2 NIC2: 192.168.2.2 The router has no dhcp configuration. Please, can anyone explain gracefully, step by step, what do I need to do? What would be the 2 NICs full configuration? What services do I need to install? I don't want devices on either network to see devices on the other network, they must be completely separate. I guess I'm missing the routing procedure step, but I have no idea how is that done. For example: tell the server that devices with gateway 192.168.2.2 must send traffic for internet to 192.168.1.1 router. Thanks in advance.

  Read the article

< Previous Page | 70 71 72 73 74 75 76 77 78 79 80 81  | Next Page >