Search Results

Search found 2692 results on 108 pages for 'ts gateway'.

Page 75/108 | < Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >

• ASUS WL-500gP v2 network between two local machines

  - by Epsiloncool

  I have two windows XP machines in my home networks, connected with ASUS WL-500gp V2 which also used as internet router. Problem is: while I have both computers normally goes to internet (used DHCP, static routes is ON, routing table is empty, operation mode is Home Gateway). I see both computers listed on the Network Neighborhood on 1st computer (wired to router), can enter to my own computer, but can not enter to other. I see only one computer (2nd) on the Network Neighborhood on 2nd computer (connected thru Wi-Fi), can enter to itself, getting error when trying to enter 1st computer address in address line (like \My1stComp). What is the problem? I totally crazy founding problem about 3 months.

  Read the article

• Internet connection resets (wifi), no device has wifi for moment

  - by Gizmo

  I have a few devices setup and I noticed this happens with both my old and new router (two different vendors&models) This happens occasionally, and I tried wireshark today and this cought my attention: No. Time Source Destination Protocol Length Info 69 6.464423000 LiteonTe_7f:64:30 Broadcast ARP 42 Who has 192.168.2.4? Tell 0.0.0.0 73 7.451146000 LiteonTe_59:65:94 Arcadyan_e1:8c:cf ARP 42 Who has 192.168.2.254? Tell 192.168.2.1 85 9.450443000 LiteonTe_59:65:94 Arcadyan_e1:8c:cf ARP 42 Who has 192.168.2.254? Tell 192.168.2.1 91 10.521000000 LiteonTe_59:65:94 Broadcast ARP 42 Who has 192.168.2.254? Tell 192.168.2.1 93 10.860953000 LiteonTe_7f:64:30 Broadcast ARP 42 Who has 192.168.2.254? Tell 192.168.2.4 97 11.099463000 LiteonTe_7f:64:30 Broadcast ARP 42 Who has 192.168.2.254? Tell 192.168.2.4 where 192.168.2.254 is the gateway/router, 192.168.2.1 my laptop ip and 192.168.2.4 my sisters laptop.. what's happening here?

  Read the article

• What are the methods of separating network spaces in a LAN?

  - by dash17291

  Please detail me the methods. My thoughts: put the servers in separate (sub)networks the servers are forced to go through the firewall but no NAT is required assign more IP addresses to the internal interface of the server choosing gateway addresses from the clients and servers IP address ranges split DNS Netfilter/{iptables, ipset} could be heavily involved, I'm talking about Linux servers. See for example: Destination NAT Onto the Same Network from internal clients Please do not explain what is NAT or DNS. This is a theoretical question, but my poor English knowledge prevent me to describe it in a fancy fashion.

  Read the article

• How to setup Microsoft Remote Desktop?

  - by jsoldi

  I'm trying to establish a connection between this app and my Win 8.1 Pro PC, but every guide I've found so far skip steps such as what to put under PC name or under Gateway. Also, should the User name be my email or something else? I've also no idea how to find or add a user in the step 6 of this guide because the only location listed is my PC and I don't even know what am I supposed to search for. I'm not even sure whether I have to add a user or this is an step I can skip. A comprehensive guide for people without experience in networking would be highly appreciated. Both my android tablet and PC are connected to the internet through a home router, in case this matters.

  Read the article

• Windows 2008 Server network issues

  - by Snowflow

  I have this one server that just doesn't want to be on the internet It's a new server, a twinblade, the other twin works, but not this one. It can connect fine to everythign else in the LAN, but cannot go out on the net It can be reached by ICMP requests over the net (the nagios server can probe it, but not ping it for instance), but not TCP Everything seems fine both in firewall and machine, i get no issues. Anyone care to help me out where i can start looking, i'm seriously confused. edit: it can ping gateway and through the sonicwall site to site VPN, it\s also able to resolve DNS. the only thing it can`t do is reach anything outside of LAN/VPN

  Read the article

• Why can't my FreeBSD 6.1 (vmware player client under Win7) do DNS in Bridged mode.

  - by Walter Stickle

  I have a 64-bit FreeBSD 6.1 client, running under Windows 7 (64-bit) via VMWare player 3.0, with networking set to bridge mode. DHCP goes fine on boot... I get correct adress/gateway/nameserver info... I have good connectivity to the world in that I can ping any host I can name by IP addr, (including both of the nameservers in resolv.conf,) ...but I can't resolve any names. Inside the Windows box, the network interface has VMWare Bridge Protocol enabled, and the windows side of things has full connectivity. dig replies with: ;; connection timed out; no servers could be reached ...even if I use "dig @server_ip_addr" to point it at a pingable, working nameserver If I set VM networking to NAT mode, I can get outbound connectivity (with happy DNS) but, of course, can't do INBOUND connectivity, which I need. Thoughts?

  Read the article

• Cisco 5505 VPN RDP not working

  - by user1058275

  I am in dire straights over here. We just changed our LAN from a 192.168.1.0 to a 172.16.4.0. We run Active Directory in our environment and our gateway is a Cisco 5505 ASA. Since the change, our clients can VPN in and make a connection but cannot RDP to any machines that they need to get to on the LAN that they VPN into. I updated the VPN address pool and DNS servers but I'm not sure what else I need to configure. I can send anything you need as I am not an expert and I really, really appreciate the help!

  Read the article

• Very Dark Windows 7 Screen

  - by user147521

  My Gateway laptop -Windows 7- screen became too dark a few days ago after I finished installing Windows automatic update. I can see nothing unless I use a flashlight. Windows login screen is the only bright screen for few seconds. What should I do to resolve this issue? I checked power-saving/ Power Options settings and rebooting in Safe Mode. I tried to lower the refresh rate but it did not allow me. The laptop adapter type is ATI Radeon Xpress series. I calibrated display color. I uninstalled and reinstalled the adapter. I tried to update the driver but the driver is up to-date. Any help would be appreciated.

  Read the article

• Why are Full GCs not running on my gcInterval I set?

  - by Brad Wood

  ColdFusion 10 Update 10 Windows Server 2008 R2 Java 1.7.0_21 I am trying to figure Full GCs to run every 10 minutes. I have used the gcInterval JVM arg in the past on earlier versions of ColdFusion with success, but I have confirmed with verbose GC logs that Full GCs are still happening on the hour (Unless the Old Gen gets so full that it forces a full collection). Here are the full JVM args from ColdFusion10\cfusion\bin\jvm.config (line breaks added for readability) Is there something else I need to be doing to get this working on ColdFusion 10? java.args= -server -Xms4072m -Xmx4072m -XX:PermSize=512m -XX:MaxPermSize=512m -Dsun.rmi.dgc.client.gcInterval=600000 -Dsun.rmi.dgc.server.gcInterval=600000 -XX:+UseParallelGC -XX:+UseParallelOldGC -Xloggc:gc.log -verbose:gc -XX:+PrintGCDetails -XX:+PrintGCDateStamps -XX:+PrintGCTimeStamps -XX:+UseGCLogFileRotation -XX:NumberOfGCLogFiles=5 -XX:GCLogFileSize=1024K -Xbatch -Dcoldfusion.home={application.home} -Dcoldfusion.rootDir={application.home} -Dcoldfusion.libPath={application.home}/lib -Dorg.apache.coyote.USE_CUSTOM_STATUS_MSG_IN_HEADER=true -Dcoldfusion.jsafe.defaultalgo=FIPS186Random -Dcoldfusion.classPath={application.home}/lib/updates,{application.home}/lib,{application.home}/lib/axis2,{application.home}/gateway/lib/,{application.home}/wwwroot/WEB-INF/flex/jars,{application.home}/wwwroot/WEB-INF/cfform/jars

  Read the article

• Need to configure multiple default gateways for four seperate physical network ports for a FreeBSD Webserver

  - by user20010

  I need to configure default gateways for four separate physical network interfaces for a FreeBSD Webserver. Basically, this is a web server that needs to be accessed by multiple WANS. I've been using various online resources, and a combination of setfib, pf, and ipfw. This web server will be deployed in multiple sites where access to next hop router info is not available, so we can't use static routes. We've used setfib to successfully create multiple routing tables and can ping beyond every default gateway we've created. Using setfib # ping ip.addr.what.ever we can ping anything available on a wan and beyond the router. The problem is we can't get Apache web server (port 80) traffic to route out when external users access the server(box). Multiple people have examples of binding setfib to ipfw commands, but none of them seem to work.

  Read the article

• Setting primary IP for VPS (out of 2 available)

  - by Flyer

  I've got a little problem. My VPS (Debian box) has 1 primary IP address, but now my hosting provider decided to assign me another one due to problems with first one. Let's say new IP is 91.222.152.20 and old one 91.221.190.170. How should I make 91.222.152.20 primary one, so that everything works on this address instead of 91.221.190.170 (like ftp, mysql etc) I tried editing /etc/newtwork/interfaces setting iface eth1 inet static address 91.222.152.20 netmask 255.255.252.0 network 91.222.152.0 broadcast 91.222.155.255 gateway 91.222.152.1 I know that network is 91.222.152.0/22 so I assume that above configuration should be right. Saved, rebooted and that ended pretty bad. Couldn't even ping box on old or new IP. Had to revert to working one. So question is. What am I doing wrong and how to do it right?

  Read the article

• Zentyal Server : Setting up secure VPN Client

  - by JustShrey

  I have officially exhausted pretty much all my google-fu trying to set this up so I'm asking my question here. For the record, I am a mid level rookie who has played around with servers in his spare time but have never worked with Zentyal Server. Now, I have been able to set up the server as a gateway, with one Network card being external and the other facing the internal Network. The Internal network computers are able to access the internet without any issues. What I need to do is to setup a open-vpn client on the central server so that all Internet data goes though the secure VPN session. As far as I can see, I can't set up the vpn session through the web admin page. Could somebody point me in the right direction? How would I go about doing this? Regards Shreyas

  Read the article

• Two NICs, one server.

  - by kobrien

  I have two NICs on a fresh install of Ubuntu 10.04 LTS. Both are config'd be dhcp. Both cards are on the same lan with same gateway. everything about the cards is the same except the IPs they get, which is what I want. What I'm trying to achieve is having both NICs operational at the same time. Currently when the server boots, it activates both NICs, but the server can't resolve any domains. If I ifdown one of them and bring it back up, the server is able to resolve domains, but the NIC I bring up won't respond to any traffic. Any ideas?

  Read the article

• What protocols will/are ISPs use for IPv6 deployment?

  - by rbeede

  Currently ISPs deal out addresses via DHCP for IPv4 dynamic (single) addresses. What protocol will/are ISPs going to use for IPv6 when they can hand a customer an entire /64 (or /48 if they are nice) block? DHCPv6, RA? For ISPs that support true end-to-end IPv6 will they provide gateway devices (similar to cable modem or true DSL bridges for example) that receive border information for that specific customer? I'm just trying to get an idea of how your common residential service customer will have to configure things in an IPv6 Internet (whenever that comes). Will it be something customers are expected to statically configure on their home wireless router? Today with IPv4 I do it like this: Modem (bridge) passes public IPv4 obtained via DHCPv4 from ISP to second device (wireless router). It in turn has its own DHCPv4 service it provides on the internal lan.

  Read the article

• Windows share through proxy

  - by jessebs

  I have a Windows share and on a different subnet. The users on the user subnet can not see the server subnet, although there is a proxy server in place on the user subnet that can. All web traffic is sent through this proxy server (squid). Is there any way to proxy a file share so the users can access it? I have tried an NTFS symlink, but I can't access the symlink through the share. The server is Windows Server 2008 R2 -- I had to stick with Windows because it is running a Remote Desktop Gateway as well.

  Read the article

• Destination host unreachable

  - by user1010101

  I have 2 router connected to 1 switch which contains two vlans, 1 router has the ip table of vlan1 and the other router have the ip table of vlan2 I have trunked both router cable to the switch. I have set 1 ip table per router which correspond to the ip address of the PC that have this router address as a gateway. When I ping from 192.168.100.2 to 192.168.200.2 it tells me that destination host is unreachable and the message is from the router 192.168.100.1. So I guess router for 192.168.100.x does not see the router for 192.168.200.x , right ? Or am I wrong ? What are good troubleshooting steps ? http://i.imgur.com/b94Ir.png is the representation of the network, i cannot post image since im not reputated enough.

  Read the article

• How to deal with redirect traffic in widows2003

  - by Huiyu

  I have set up an OpenVPN server on Windows 2003, and I want to route all client traffic through the VPN, so that my clients can connect to the Internet through the VPN server. In the server configuration, I added push "redirect-gateway def1". I know the server needs to be configured to deal with the traffic somehow: for example, on Linux, I can use iptables -t nat -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE. The problem is, I don't know how to deal with the traffic on Windows Server 2003. Is there any way to accomplish this?

  Read the article

• Why does my computer erratically scroll up and down?

  - by Jerry

  I am running Windows XP with SP3 on a 2002 Gateway machine. For the last few days I have experienced the problem of erratic scrolling that seems to have a mind of its own. If I am on a window with a scroll bar, the window scrolls up and down the page erratically, often when I have not initiated it. I am not sure but think this started following a routine Windows Update. It is doing it now as I type this. It is totally distracting to being able to do anything while it is occurring. It does it a while then there are occasional pauses in the scrolling then it starts up again. Any suggestions on fixing this?

  Read the article

• How to control routes added by RasDial

  - by Robert Dodier

  I am using the RasDial function on a Windows box (Windows Server 2008) to dial a device from which the server then reads data. It seems that some new routes are added to the network routing table when the dial-up connection is made. That interferes with other network interfaces on the server. In particular, RasDial adds a default route which routes traffic to the device, which makes the server unreachable until the connection is dropped. Is there a way to control which routes are added by RasDial? I have been studying Microsoft's document for RasDial and associated items (RASDIALPARAMS, RASDIALEXTENSIONS) without finding anything about routing. There is an option for "Use default gateway on remote network" when configuring a VPN, but I don't see how to apply that in this case. Thanks for any light you can shed on this problem.

  Read the article

• find wireless-repeater ip (router)

  - by Brtrnd

  Really long time ago I set up my dd-wrt router up as a repeater. It works well; in the summer I place it near the garden and I have wifi in the garden. I would like to revisit te settings and see if it would be a good idea to install openvpn. The problem is: I don't remember the ip of the router. I probably followed the setup instructions on the dd wrt wiki. it doesn't show up on the management-console of my main router (a docsis3 modem); it doesn't show up if I do an IP scan of the whole class B; it doesn't show as the gateway when i connect to it (wired or wireless). Any ideas on how I could find the web-interface?

  Read the article

• Vista Home Premium won't connect to network.

  - by Ice

  I deinstalled some software (e.g. some Toolbars for IE and Norton security suite, because the free trial period of 60 days is run out and so i want to switch to microsofts free security essentials). But now i cannot connect to the network again: Neither over LAN nor over WiFi. Neither with standard DHCP ON (sets a 169.254.x.y address) nor with fixed IP-Address. No error during changing the settings. Ping to the Gateway e.g. doesn't work and gives "generall failure". The DHCP-Client sets no IP-Address. There is allways only 'local access' on every network-connection. i ran out of ideas, please help. UPDATE per 2011-03-11: I followed each and every hint but nothing changed. I did a research on microsofts homepage through all the sites belonging to network but nothing helped. What can i do next?

  Read the article

• Two IP ranges on eth1 configuration for centos 6.2

  - by Trickzzz

  i have a dedicated server, with "Virtuozzo" on it running VPS's. I have: eth0 - which is configured to the internal network, that one is fine. Now I have: eth1 - which has two ranges routed through this device. x.x.134.x (which has 12 IP's sequentially) x.x.132.x (which has 5) eth1: DEVICE="eth1" HWADDR="00:25:90:37:65:67" NM_CONTROLLED="yes" ONBOOT="yes" IPADDR="x.x.134.x" NETMASK="255.255.255.240" GATEWAY="x.x.134.x" I tried using this with another file as well named "ifcfg-eth1:1" in /etc/sysconfig/network-scripts/ any ideas why the containers on eth1:1 would not link up to the network? Virtuozzo also thinks that eth1:1 is the primary network now, which isn't right?

  Read the article

• what route to add to windows so that..

  - by baobeiii

  what route to add to windows so that while using openvpn i have internet connectivity, but if openvpn tunnel collapses then my computer has no routes to use and so has no connectivity. My computer normally needs the default route 0.0.0.0 mask 0.0.0.0 192.168.1.254. I just need a route that only allowed traffic destined for the openvpn server ip. The traffic has to go through 192.168.1.254 however as that is my home networks internet gateway router thingy. Thanks.

  Read the article

• Does Asus F8SV supports 1920*1080 resolution through DVI output? [closed]

  - by Col

  Devices: Asus F8Sv Laptop (Windows 7 ultimate, GeForce 8600m GT, display driver is 301.42, detected and downloaded from nvidia.com, VGA and DVI output interface) Gateway 23 inches LCD monitor (VGA, DVI-D with HDCP, and HDMI input) 18 pins DVI cable, VGA cable, both new. Problems: When connect laptop to monitor by VGA, resolution is automatically adapted to 1920*1080; but when using DVI connection, resolution on monitor is fixed to 1024*768, which is lower than my laptop default 1280*800. The maximum resolution in windows control panel is only 1024*768, while the Nvidia control panel provides options 1920*1080p and 1920*1080i, but clicking apply button does not work, the resolution just can not change. Possibly reason I guess: GeForce 8600m GT does not support 1920*1080 resolution through DVI outputs. Can anyone confirm it or give the real reason? edit: Problem solved by buying a HDMI to DVI-D adapter. Using this adapter and a HDMI cable, I can now enjoy 1080p movie.

  Read the article

• Server IP must be a LAN IP (Port Forwarding Netgear Router)? [closed]

  - by rphello101

  I'm trying to set up a server (Apache) on my computer (fairly new to it). As I understand it, for it to be accessible to other computers, I need to forward port 80. When I try to forward the port though, I get the error: Server IP must be a LAN IP. I noticed in ipconfig that my default gateway is different than my wireless router. My computer is not hardwired, not on WiFi. Furthermore, I do not, at this point, have a static IP. I read that it should still work with a dynamic IP until it changes. Any ideas on what I can do? I'm using Windows 7 in case it matters.

  Read the article

< Previous Page | 71 72 73 74 75 76 77 78 79 80 81 82  | Next Page >