Search Results

Search found 20833 results on 834 pages for 'oracle advice'.

Page 752/834 | < Previous Page | 748 749 750 751 752 753 754 755 756 757 758 759  | Next Page >

• Laptop CPU fan not working properly

  - by Smith

  My laptop's CPU fan is suddenly acting very bizarre, and I am at a loss for what to do so I am asking for some help. Specifically, the fan is not even starting to spin until the CPU reaches 60 degrees Celsius (checked through HWmonitor). Once it is on, however, it properly stays on even when the CPU gets back to idle temps around 38 Celsius. Before, the fan was simply starting with the computer and staying on like normal. I've checked this for consistency both by allowing cold boots to ramp up temperature to 60 Celsius (the slow climb also causing the laptop to become unreasonably warm near the heatsink), and also running Prime95 immediately to kickstart the fan (this works every time). The fan seems to be stationary when turning the computer on from either sleep or shutdown. The fan will start at POST very briefly, and then stop completely. I've checked the BIOS for a SmartFan setting but haven't found any. I've opened the case to check for dust or debris and have not found anything (I applied some canned air to the area just in case). The laptop is a Lenovo ThinkPad Edge E430 and the CPU is an Intel Core i5 3210m @ 2.5 GHz. Any advice would really be appreciated.

  Read the article

• Choosing local versus public domain name for Active Directory

  - by DSO

  What are the pros and cons of choosing a local domain name such as mycompany.local versus a publicly registered domain name such as mycompany.com (assuming that your org has registered the public name)? When would you choose one over the other? UPDATE Thanks to Zoredache and Jay for pointing me to this question, which had the most useful responses. That also led me to find this Microsoft Technet article, which states: It is best to use DNS names that are registered with an Internet authority in the Active Directory namespace. Only registered names are guaranteed to be globally unique. If another organization later registers the same DNS domain name, or if your organization merges with, acquires, or is acquired by other company that uses the same DNS names, then the two infrastructures cannot interact with one another. Note Using single label names or unregistered suffixes, such as .local, is not recommended. Combining this with mrdenny's advice, I think the right approach is to use either: Registered domain name that will never be used publicly (e.g. mycompany.org, mycompany.info, etc). Subdomain of an existing public domain name which will never be used publicly (e.g. corp.mycompany.com). The "never used publicly" part is a business decision so its probably best to get sign off from those in the company authorized to reserve domain names and subdomains. E.g. you don't want to use a registered name or subdomain that the marketing dept later wants to use for some public marketing campaign.

  Read the article

• How to disable my laptop's defective keyboard?

  - by Kolink

  I have an Alienware M17x R2, and after a couple years of use I started having problems with the keyboard: Intermittently, and without warning or apparent cause (even if I'm not touching the computer), the S key (and more recently the D key) will start firing incessant signals until I hit the offending key. I've been using a USB keyboard, which is conveniently exactly the right size to fit over the built-in keyboard without touching any buttons. However, even as I type the defective keyboard will fire its stream of signals. I have contacted Dell about this, twice in fact. The first time, I was just bluntly told that they don't ship replacement keyboards. The second time I was told that they did, but they were out of stock and they would contact me when they were in stock again. They haven't contacted me since. I can't seem to work out which device to disable in the device manager. Here's a screenshot of what I have: None of the keyboard devices have "Disable" in their context menus, only "Uninstall"... so you'll understand if I'm hesitant to try anything myself. Any advice on how to fix this?

  Read the article

• Clean installation of RHEL 5.5 claims package "desktops" is missing

  - by TKguru42

  Hi all, I'm a student worker in the CS department of my university, so please forgive me for any unprofessional descriptions. Simplified explanations are appreciated. I recently replaced some bad graphics cards in a few public workstations. The machines are all the same model. Before putting them back on the network I did fresh installs of RHEL---first I tried 5.4, but yum update ran into all sorts of ugly dependency errors and if I tried to remove any of the problematic packages, the whole operating system FUBAR'd. Using RHEL 5.5 gave me the same errors during install saying that "java.1.5.1-sun*" and "desktops" were missing, but yum update didn't have any dependency problems. Now that I tried logging in through the GUI, I encounter no GUI past the standard RHEL login page. The desktop is a uniform light teal and there's no system tray. An xclock window and an xterm window are open, and Firefox opens automatically, but that's it. Nothing else. What's REALLY confusing is that the computer claims that gnome is already installed, except it clearly isn't working. Any help or advice is greatly appreciated. If it helps, our department uses kickstart to run our standard Linux installs. I can try to get the script if that would be of use. Thank you!

  Read the article

• Follow through - How to setup equivalent USVIDEO.ORG DNS-Proxy on Linux

  - by DNSDC

  I'm quite keen to setup similar service (but FREE) and seems you know how to do this. "you need to run your own private dns with artificial records for example pandora.com you also need a real dns to fall back on. now that all requests for these sites are going to your US located box you can open up port 80 on squid and listen for the traffic. your cache_peer settings should allow you to map each domain to their real ip. The trafic now flows initially from your US located box to the service but then the server responds it responds directly to the host. no magic here. I won't share the fine details as it probably best serves all to not over exploit this." Did you mean we need to 1. Setup Forward-only DNS on a US-based server/ip? 2. Setup cache_peer and cache_peer_domain in Squid, I got this. 3. Any iptables rule, prerouting, postrouting rules needed to accomplish this? Appreciate your expert advice. Cheers, Don

  Read the article

• Server taking too long to respond error

  - by DCJones

  Hi, This is my first post on serverFault and my first entry in to web server configuration. The hardware and software. CPU: GenuineIntel, Intel(R) Core(TM)2 Duo CPU E7500 @ 2.93GHz OS: Linux 2.6.18-128.el5 Memory: 2Gb Background. I am running a small database (MySQL), around 1000 records with each record containing 44 fields. At the start of each day “00:01” the tables are cleared and populated with fresh data. The are 10 remote PCs all running Winodws XP and Firefox internet browser. All remote PC’s are connected to the internet using a min 4Gb broadband connection. Each remote PC runs a URL which displays a dynamic page of data which is refreshed every 20 seconds. This is a continual process 24 hours a day. I problem I am having is on odd occasions throughout the day the PC browser error with “Server taking too long to respond error”. What I am trying to find our is if I have the correct setting in the httpd.conf file on the server. Any help or advice anyone can provide would be very helpful. Best regards Dereck Server config file: httpd.conf ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 120 KeepAlive On MaxKeepAliveRequests 200 KeepAliveTimeout 5 StartServers 8 MinSpareServers 5 MaxSpareServers 20 ServerLimit 256 MaxClients 254 MaxRequestsPerChild 4000 StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 150 ThreadsPerChild 25 MaxRequestsPerChild 0

  Read the article

• Exchange on SBS2003 not receiving mail, but sending via telnet works

  - by YDdraigLas

  Last week we had a problem on our SBS2003 server where our external connection dropped out and I was only able to restore it by running netsh winsock reset catalog and netsh int ip reset. Thinking all was well, I went home for the weekend and came in today to find that we haven't received any external emails since before the original problems occurred. There are plenty of examples of this on the internet, usually to do with a firewall issue, but the odd thing here is that when I connect using telnet I can send an email and it goes straight through and into my inbox. When I send an email from Gmail or Hotmail nothing comes through at all. Internal emails are also unaffected, as are outgoing emails. There have also been a couple of emails that have come through for other users, both out-of-office replies, if that's relevant. I've run the CEICW several times, checked all the NIC settings, but no joy. Before I give up trying to fix this and reinstall the whole server, has anyone come across this problem before? I have only found fleeting references to this in previous searches and no real answers. Any advice gratefully received.

  Read the article

• apache access and error log written in same file

  - by user196075

  i have issue that access and error log are written in same file ! , the configuration in virtualhosts.conf as the following : <VirtualHost *:80> ServerName ************ ServerAdmin support@************8 DocumentRoot /var/www/html/*********.com ErrorLog /var/log/httpd/********/********.com_error_log CustomLog /var/log/httpd/********/********.com_access_log combined <Directory /var/www/html/***********.com> Options -Indexes FollowSymLinks AllowOverride All </Directory> </VirtualHost> as you see from the configuration each access and error logs should be save separately , but both logs are written in *.com_access_log , i have double check all permission , group and owner ... can't find anything wrong previous error in log file : [Thu Sep 19 14:15:02 2013] [error] [client 192.168.10.54] client denied by server configuration: /var/www/html/**********/show_has_offers.php i have tried to generate same error , i can find the hit in access log only as the following : 192.168.10.75 - - [24/Oct/2013:08:11:14 +0000] "GET /show_has_offers.php HTTP/1.1" 404 1586 "-" "Mozilla/5.0 (X11; Linux x86_64; rv:22.0) Gecko/20100101 Firefox/22.0" 0 17332 and nothing in error log !! Please advice ...

  Read the article

• Exchange 2007 Backup - For a newbie

  - by mew3900

  I am trying to setup an exchange 2007 backup solution. After doing a lot of reading, Microsoft have decided in server 2008 unless you are willing to spend a great deal on a 3rd party solution you are pretty stuck! Essentially what I have been asked to do is perform an off-line file backup of our current exchange server and replicate this onto a new 2nd server. The reasoning behind this is that we need to upgrade our current installation of exchange 2007 to SP2 so that the exchange plug-in for windows server backup will be available to us. From this I can then actually take an exchange aware backup weekly and take it off site. Ideally then also we can migrate to this new server and keep the old one as a fail over. Is there a way I can copy across the files required onto a second server, although I doubt very much it is that simple. I may be barking up completely the wrong tree, however I have very limited knowledge with Exchange and any help and advice on how I would resolve this would be much appreciated. Thanks in advance

  Read the article

• Port 80 not accessible Amazon ec2

  - by Jasper

  I have started a Amazon EC2 instance (Linux Redhat)... And Apache as well. But when i try: http://MyPublicHostName I get no response. I have ensured that my Security Group allows access to port 80. I can reach port 22 for sure, as i am logged into the instance via ssh. Within the Amazon EC2 Linux Instance when i do: $ wget http://localhost i do get a response. This confirms Apache and port 80 is indeed running fine. Since Amazon starts instances in VPC, do i have to do anything there... Infact i cannot even ping the instance, although i can ssh to it! Any advice? EDIT: Note that i had edited /etc/hosts file earlier to make 389-ds (ldap) installation work. My /etc/hosts file looks like this(IP addresses as shown as w.x.y.z ) 127.0.0.1   localhost.localdomain localhost w.x.y.z   ip-w-x-y-z.us-west-1.compute.internal w.x.y.z   ip-w-x-y-z.localdomain

  Read the article

• Cannot Install Windows 7 SP1 (64-bit)

  - by Clever Human

  I have tried every way I know how to get Windows 7 SP1 to install. It fails every time. Below is what looks like the relevant contents of the CBS.Log file. If there are further details that would help or more information I can gather, I will get it. 2011-08-15 10:32:52, Info CBS Startup: Package: Package_for_KB976902~31bf3856ad364e35~amd64~~6.1.1.17514 completed startup processing, new state: Installed, original: Installed, targeted: Installed. hr = 0x80070490 2011-08-15 10:32:52, Info CBS WER: Generating failure report for package: Package_for_KB976932~31bf3856ad364e35~amd64~~6.1.1.17514, status: 0x80070490, failure source: CBS Other, start state: Partially Installed, target state: Installed, client id: SP Coordinater Engine 2011-08-15 10:32:52, Info CBS Failed to query DisableWerReporting flag. Assuming not set... [HRESULT = 0x80070002 - ERROR_FILE_NOT_FOUND] 2011-08-15 10:32:52, Info CBS Failed to add %windir%\winsxs\pending.xml to WER report because it is missing. Continuing without it... 2011-08-15 10:32:52, Info CBS Failed to add %windir%\winsxs\pending.xml.bad to WER report because it is missing. Continuing without it... 2011-08-15 10:32:52, Info CBS SQM: Reporting package change completion for package: Package_for_KB976932~31bf3856ad364e35~amd64~~6.1.1.17514, current: Partially Installed, original: Partially Installed, target: Installed, status: 0x80070490, failure source: CBS Other, failure details: "(null)", client id: SP Coordinater Engine, initiated offline: False, execution sequence: 517, first merged sequence: 517 2011-08-15 10:32:52, Info CBS SQM: Upload requested for report: PackageChangeEnd_Package_for_KB976932~31bf3856ad364e35~amd64~~6.1.1.17514, session id: 101457924, sample type: Standard 2011-08-15 10:32:52, Info CBS SQM: Ignoring upload request because the sample type is not enabled: Standard I have downloaded the service pack and ran it from the EXE, I have installed it from Windows Update, I have ran all the "troubleshooting" trouble shots I could find. Nothing has worked so far. Any advice would be appreciated.

  Read the article

• Are my web server permissions for uploading correct?

  - by user1699176

  I'm on debian and I have my website in the directory /srv/www/mysite.com/public_html I set chown for www-data:www-data on /srv/www. I have root disabled and created a sudo user which is id 1000:1000. I would also like to use this user to upload to /srv/www so I added my sudo user to the www-data group. I originally got a message saying that I didn't have permissions to upload a file to that directory. After playing around with multiple permissions for a while I finally was able to upload properly, but I'm not sure if this set up is correct. I'm hesitant to change it for now since it actually works, so I thought I'd ask for advice. I think what I ended up doing was this: sudo chown -R www-data:www-data /srv/www sudo chmod g+s /srv/www sudo usermod -aG www-data myuser sudo chgrp -R www-data /srv/www sudo chmod -R g+w /srv/www When I was finally able to successfully upload a file (with FileZilla) it showed the owner as myuser myuser. Shouldn't it have been www-data myuser? My question is whether this is correct and if there are any potential security issues? For example, I wasn't sure if I was actually supposed to use "myuser" to own the /srv/www directory instead sudo chown -R myuser:myuser /srv/www or maybe sudo chown -R www-data:myuser /srv/www If you need more info, let me know, thanks.

  Read the article

• Random HTTP 413 error on apach2/php/joomla site

  - by jfab

  I have a Joomla site, and every once in a while when I submit something via a form, I get a HTTP 413 error: Request Entity Too Large The requested resource /index.php does not allow request data with POST requests, or the amount of data provided in the request exceeds the capacity limit. In the error.log file I get: Invalid Content-Length, referer: [site]/index.php It doesn't seem this has anything to do with the actual size of the request, for the following reasons: a) I tinkered with the configuration of both Apache, and PHP. In Apache I tried increasing LimitRequestBody, and in PHP post_max_size, max_input_vars, memory_limit, and even upload_max_filesize. Every value is far beyond what is sent in a typical request that generates an error. b) The error pops up quite randomly, and often just hitting refresh allows me to get through. c) I checked the request in Fiddler to make sure everything is right with the content-length stated in the header, and the content of the request itself. Everything appears to be in order. A curious thing is that when I resent the exact same request via Fiddler, I never got the error. It seems I can only recreate it through a browser. So I'm at my wit's end here. I don't even know where to look for the problem anymore. I don't know if it's Apache or PHP (though I can't find anything in PHP error logs, so maybe that means Apache is the more likely culprit?), or PHP in general, or my Joomla site in particular (my bets were on Joomla until a recreated the error on a test script, with a very basic post form, though it does pop up much more often on the Joomla site). If anyone can give any advice on where to even begin with this, I'll be very grateful!

  Read the article

• Powerpoint not drawing in slide properly...

  - by commradepolski

  So got another issue to post about. I have a user here who uses powerpoint a lot, Office 07 with SP2. When he opens up the presentation, powerpoint opens fine without errors, but does not draw in the main slide properly. So to better explain that, the list on the left hand side, that shows the slides and what order they are in, loads up fine. You can see the slides and the content etc. When you click on a slide, to edit it, it does not draw in on the editing screen. Not really sure how to explain that. The screen where the work on the slide is done, is what is affected. This is a screen shot from my pc not the users. So instead of the screen saying "Click to add title" it would be improperly drawn such that if I were to drag an explorer window across it, it would leave a trail. I have tried reinstalling office, updating it, as well as giving the user a new windows image and nothing has helped. Any help or advice is appreciated.

  Read the article

• Windows 7, Black screen with cursor, impossible to logon

  - by PJC

  First - I have gone through as many possible solutions I've found here and elsewhere. [Edit - to describe the issue in more detail, the PC appears to boot correctly, but instead of the logon screen, I have been getting a black screen WITH the pointer cursor, and it responds correctly to the mouse. Pressing CTL-ALT-DEL brings up the logon screen's background, but with no logon area nor any other content. This screen was at the full resolution before I uninstalled the graphics driver in safe-mode.] I also just ran a full up-to-date AVG scan from boot media. [Edit - the AVG scan, which was updated to today's virus signatures, found no issues at all.] So - steps I've tried: Safe Boot, Restore from before the issue - done, no help. Uninstall the graphics driver - done, now i have a 1024x768 fallback screen, still no way in. sfc /scannow - only doable from Safe boot obviously, but no change. [Edit - booting from restore media, performing a startup repair and...]Restore further back - restored to 2 days ago, and I'd had many reboots since then with no problem. Enable autologin to try to get beyond the login screen - done, doesn't work. It seems the best advice is complete reinstall, but I really don't want to do that because it'll take 3-4 days to add all the apps I use. Some key points to note - in both states - before and after removing the video driver, I always had a mouse cursor on the screen. CTL-ALT-DEL flashes up the login background, but no login info. I can (and often do) reinstall from scratch, but was at a fairly stable state before this, and would prefer not to. -Paul

  Read the article

• Different behaviour when running exe from command prompt than in windows

  - by valoukh

  Forgive me if I'm not using the correct terminology here but I'll try to explain the issue I'm having as best I can! We use a program that allows you to view video footage from several cameras, and it works in such a way that when it is opened it then automatically loads several video files within its interface. These video files are stored in a subfolder, e.g. "videos\video1.asf", etc. I didn't create the program so I can't say what method it uses to open the files. The files are stored on a network server and are being accessed via a share/UNC path. When the file is run from windows explorer (by navigating to the network share and double-clicking the exe), it works perfectly. When the file is run via the (elevated) command prompt (e.g. by typing the \server\path\to\file.exe) it opens, but the corresponding video files do not load. I am trying to create a script that launches the program via the command prompt, so the first step is finding out why the two actions above have different consequences. Any advice on how running executables from the command prompt could produce a different result would be greatly appreciated. Thanks

  Read the article

• Toshiba Satellite C665 Rebooting from Standby

  - by Coodu

  I currently am working on a C665 with a strange issue. When the panel is closed the notebook will put itself to sleep in the usual way, and the power LED changes to the pulse to indicate that the device is asleep. However, when the panel is opened to resume using the notebook, the system will restart itself, instead beginning from the Toshiba logo and proceed to boot back in to W7. I should also note that each time this occurs, the "Windows Startup Recovery" option occurs, indicating that the system was not shut down correctly. Some things I have tried: Updated to latest Toshiba BIOS. Returned BIOS settings to their defaults. Swapped Memory to known good module, tested KGM in both memory slots within system. Confirmed that power settings are set to sleep/wake when power button is pressed. Ran a quick HDD fitness test using a parted magic USB stick. Checked for BSOD logs using BlueScreenView, none found. Ran src, no violations found. Any ideas? I have a good feeling the system is restarting itself, but in the event viewer there is a "Kernel Power" error, but it simply says "The system was not shut down correctly." Perhaps a bad driver? I'm not sure. Any advice would be great.

  Read the article

• Mysql InnoDB and quickly applying large updates

  - by Tim

  Basically my problem is that I have a large table of about 17,000,000 products that I need to apply a bunch of updates to really quickly. The table has 30 columns with the id set as int(10) AUTO_INCREMENT. I have another table which all of the updates for this table are stored in, these updates have to be pre-calculated as they take a couple of days to calculate. This table is in the format of [ product_id int(10), update_value int(10) ]. The strategy I'm taking to issue these 17 million updates quickly is to load all of these updates into memory in a ruby script and group them in a hash of arrays so that each update_value is a key and each array is a list of sorted product_id's. { 150: => [1,2,3,4,5,6], 160: => [7,8,9,10] } Updates are then issued in the format of UPDATE product SET update_value = 150 WHERE product_id IN (1,2,3,4,5,6); UPDATE product SET update_value = 160 WHERE product_id IN (7,8,9,10); I'm pretty sure I'm doing this correctly in the sense that issuing the updates on sorted batches of product_id's should be the optimal way to do it with mysql / innodb. I'm hitting a weird issue though where when I was testing with updating ~13 million records, this only took around 45 minutes. Now I'm testing with more data, ~17 million records and the updates are taking closer to 120 minutes. I would have expected some sort of speed decrease here but not to the degree that I'm seeing. Any advice on how I can speed this up or what could be slowing me down with this larger record set? As far as server specs go they're pretty good, heaps of memory / cpu, the whole DB should fit into memory with plenty of room to grow.

  Read the article

• Ubuntu 12.04 VirtualBox on powerful W7 quite slow

  - by wnstnsmth

  I own a Thinkpad T420s with 8GB RAM, 160 GB SSD and a quite fast i7 processor. Summa summarum a very fast computer that works perfectly. Now, I am not very impressed by the performance of my Ubuntu 12.04 virtual machine running on VirtualBox 4.1.18. I assume that Virtual Machines are always a bit slower than the guest system, still I think it should be more performant given the hardware settings I give it: 4096 MB RAM 1 CPU without CPU limitation (I would like to give it more but then it does not seem to work - I am not experienced in this maybe somebody could give me advice on this too) Activated PAE/NX, VT-x/AMD-V and Nested Paging 96 MB Graphics Memory (no 2D or 3D acceleration) ~ 14 GB disk space, currently about 7 GB are used Maybe I misconfigured something, could you give me a hint please? Thanks! Edit: What I mean by slow is that for example switching tabs in the browser (whether FF or Chrome) only goes with a 0.5s delay or something, as well as switching application windows and/or double-clicking applications in the dock to get all open windows.. opening Aptana takes about a minute whereas opening something like Photoshop on the guest system takes 5 seconds

  Read the article

• setting up vpn server

  - by Lock

  I need help in visualising how to setup our VPN box when we move to our new network with Telstra. We have a safe@office 500P, which has a public IP and a private IP of 192.168.19.2. It is physically connected to our router, which has 4 different interfaces, one being 192.168.19.1. On the VPN box, we have a static route to forward everything to 192.168.19.1 which is the router, and from there it works out where to go. Now, we are moving to a Telstra WAN and things are setup a little differently. Our head office router has only 3 interfaces- 1 is for the link to the switch that has the fibre connection (so our route to the internet and other branches), 1 is for our 10.10.20.x network and one is for the local branch network. I really have no idea how to set this up as with the new setup, we will not have a port for it to plug into on the router. Could I just plug it into the 10.10.20.x network? Would I have to give it a public IP or can we just forward through the ports that it would use? Another suggestion was to VLAN our switch into two networks- one for the 10.10.20.x network and one for the network the VPN currently sits on (192.168.19.x), and setup the router to trunk between the port and the switch. Not sure how to do this. Sorry VPN's are definitely not my strong suit. Any advice appreciated!

  Read the article

• USB Diskdrive cannot be formatted nor accessed

  - by Dmolish

  So I have just recently bought and 8GB USB stick(Kingston DT 100 G2) on which I had installed Linux. However I needed to reinstall said Linux so I formatted the stick to "default" settings which includes FAT32 filesystem. Later when the install process kept getting errors, I got advice that the problem might be with the FAT filesystem. I decided to try and format the stick to NTSF (format G:/fs:ntsf) but the formatting failed and the drive broke down. And with breaking down I mean you cannot access the drive anymore and when you plug it in Windows asks if I want to format the drive but despite my will the format always fails. To fix this I tried changing it back to FAT32 (format G:/fs:fat32), but i get "Error in IOCTL-call". Second thing I tried was trying to reset the filesystem with some 3rd party application like HP USB Disk Storage Format Tool. But the programs didn´t regocnize any media on the drive. So now I´m in the situation that I haven´t got any idea on what to do next. Is the drive recoverable or did I just create a piece of waste metal.

  Read the article

• Windows-7 Ultimate 64 bit wont connect to my wired/wireless networks

  - by A302

  Windows 7 Ultimate 64 bit. Everything was working fine & then just stopped working. The nic card Realtek PCIe GBE Family Controller is enabled but does not connect to my router (cables & router ports are good). Wireless Atheros AR5007EG is enabled but the connection is limited (encryption type / key have been verified). A laptop running XP can connect both wired / wireless. SSID is not being broadcast, connect to network if it is not broadcasting is checked. Have checked services.msc for Bonjour & did not see it listed. Network & sharing center does not list any active networks. Device manager lists both devices as functioning properly. Router configuration has not been changed. Virus scan has not found anything. I would like to fix this rather than using Acronis to do a system restore. Thanks in advance for any advice offered in solving this. 26 Jan, the nic card & wireless are working using PCLinux OS Live CD. It appears that the problem is Windows 7 related.

  Read the article

• Using Openfire for distributed XMPP-based video-chat

  - by Yitzhak

  I have been tasked with setting up a distributed video-chat system built on XMPP. Currently my setup looks like this: Openfire (XMPP server) + JingleNodes plugin for video chat OpenLDAP (LDAP server) for storing user information and allowing directory queries Kerberos server for authentication and passwords In testing with one set of machines (i.e. only three), everything works as expected: I can log in to Openfire and it looks up the user information in the OpenLDAP database, which in turn authenticates my user with Kerberos. Now, I want to have several clusters, so that there is a cluster on each continent. A typical cluster will probably contain 2-5 servers. Users logging in will be directed to the closest cluster based on geographical location. Something that concerns me particularly is the dynamic maintenance of contact lists. If a user is using a machine in Asia, for example, how would contact lists be updated around the world to reflect the current server he is using? How would that work with LDAP? Specific questions: How do I direct users based on geographical location? What is the best architecture for a cluster? -- would all traffic need to come into a load-balancer on each one, for example? How do I manage the update of contact lists across all these servers? In general, how do I go about setting this up? What are the pitfalls in doing this? I am inexperienced in this area, so any advice and suggestions would be appreciated.

  Read the article

• Linux Has Become Very Slow Dealing With Large Data

  - by Kohjah Breese

  Last year I bought a computer, for around $1,800, so it is relatively high-end. When I first got it I was particularly pleased at how quick it dealt with large MySQL queries, imports and exports. But somewhere along the way something has gone wrong and I am not sure how to diagnose the problem. Any job that involves processing large amounts of data, e.g. gzipping file c. 1GB+, UPDATEs on large MySQL tables etc. have become very slow. I just performed an intensive alter statement on a 240,000,000 row table on a remote server, which is lower spec. This took about 10 minutes. However, performing the same query on a 167,000,000 row table on my computer went fine until it hit 860MB. Now it is only writing about 1MB every 15 seconds. Does anyone have any advice as to debugging what the issue is? I am using LinuxMint (based on Ubuntu 12.04.) The home partition is encrypted, which really slows down gzip. I have noticed the swap is barely used, but am not sure if that is because there is more than enough RAM. The filesystem is ext4. The MySQL server is on a separate hard drive, but it was fine when I first installed it. Other than the above issues, there are no other problems with it. I am going to install a fresh Ubuntu on the 4th hard drive to see if that is any different.

  Read the article

• please take a look at my server's ram usage

  - by user66779

  Hi, i am a noob with servers. I have a centos5.5 vps with 512mb ram. My goal is to have it host just one magento store. I've installed Magento on the server without any control panel, by just installing lamp myself and whatever php extensions were necessary to get Magento to install. As soon as i visit my magento store, suddenly the ram on the vps is almost completely used, with only about 100mb left. Please see this screenshot of htop taken after just myself visited the website. http://img714.imageshack.us/img714/1944/screenouv.png As you can see there's only around 100mb left. Is that normal? I'm wondering if i might have done something stupid with the server that makes it very resource hungry. I installed apache from the centos base repo, php version 5.3 from the ius repository and mysql 5.1 also from ius repo. I haven't changed any of the default config files for any of these except to make memory_minimum 256 in php.ini. Is there anything i can do to make more ram free? I'm clueless but i see each Apache daemon is using 8% of available ram, and AFAIK each visitor needs one Apache daemon. So i would run out of ram with just a handful of visitors. Thanks for your advice.

  Read the article

< Previous Page | 748 749 750 751 752 753 754 755 756 757 758 759  | Next Page >