Search Results

Search found 2279 results on 92 pages for 'cable clutter'.

Page 8/92 | < Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >

• eSata plugged into Sata socket via adaptor cable very slow

  - by Jon

  Why would an external eSata Drive (xSonic with 500Gb notebook Hard Drive) run ok on a Silicon Image based PCI-E to eSata adaptor at about 35MB/s, But then run really slow when plugged into NForce4 Sata socket via cable? I have another version of the problem with Really slow 1MB/s!!! performance on a ASUS P5K Pro Motherboard with E8400 CPU. This time the same card is plugged into a PCI-E socket. The same eSata drive is plugged into the Esata port on the card. All this is running on Windows XP Pro 32bit. Any suggestions on how to diagnose the problems??

  Read the article

• Ultrium 3 tape drive shoe-shining, 3Mb/s: and it's not the cable

  - by mowsala

  I have a HP 960 Ultrium 3 tape drive. Since I got it, (second hand, £90) I've been experiencing shoe-shining. Writing with tar in Linux, I average about 3Mb/s write speed. I've tried replacing both the SCSI card and the cable now, both of which made no difference at all. A curiuos observation I have made is that the write rate is not consistent. Sometimes it will write for over a minute without shoeshining, but more often, just a few seconds. I've also tried several tapes, different source drives, and even writing from Windows Backup, to no avail.

  Read the article

• Splitting Ethernet cable

  - by Nathan

  I am looking for the best way to network my small business. I have an office where my router/modem are located, and then 2 more computers in another room. I can route Ethernet to this room with about 75 ft of cabling, and I would like to do this because my computers on Ethernet are getting 3x the speed as computers on wireless. Is there any way I can use just one Ethernet cable to span the 75 feet, and then maybe 2 smaller ones to go to the two computers from there? If there's a simple way to do this, maybe with a connector that would be ideal, as opposed to buying over 150 ft of cabling. Thanks!

  Read the article

• Connecting two pcs through cable, at the same time as wireless

  - by Steffen

  I've got 2 pcs setup with WLAN - however when I copy files between the machines it takes forever (obviously, since I run 801.11g). So I thought, why not just connect them directly with a cable (my wireless router is the other end of the house, that's why I don't use cables to that) However how should I configure the LAN connection on each machine, so I can use it for transferring files between them, whilst using my WLAN to access the Internet ? I was thinking about letting one machine be gateway, but then Windows pops up with a lot of warnings (basically it says this won't work when you're using two disjoint networks) And now I'm at a loss as to what to try.

  Read the article

• Sharing wireless internet connection between 2 Ubuntu 10.04 systems using cross-over cable

  - by Gary

  I have a Lenovo T60 with Ubuntu 10.04 connected with a cross-over cable to a Dell Vostro 1400, also running Ubuntu 10.04. My internet is coming into the Lenovo through an external wireless antennae, and I want to share the internet with the Dell. On the Lenovo: eth0 connection has IPv4 Settings 'Shared to other computers' I can ping the Dell (10.42.43.10) successfully I can use mtr to trace to www.google.com successfully On the Dell: eth0 connection has IPv4 Settings 'Automatic DHCP' I can ping the Lenovo (10.42.43.1) successfully when I use mtr to trace to www.google.com, I can only reach 10.42.43.1 I must be missing some setting, but cannot see what it is; can anyone help me?

  Read the article

• Twisted pair cable twists and unwanted signals issue

  - by ziaharipur

  I am confused about one point I have read the following paragraph from the networking book. “the twists in the twisted pair cable are used to avoid the unwanted signals. For example one twist, one wire is closer to the noise source and the other is farther; in the next twist the reverse is true. Twisting makes its probable that both wires are equally affected by the unwanted signal. This means that the receiver which calculate the difference between the two receives no unwanted signal.” Now ok I understood the purpose of twists but I am confused about how receiver will calculate the difference when it will receive the signal?. How unwanted signal will be eliminated ? Another thing that I want to make clear is , I am beginner please provide such an answer that can be understood.

  Read the article

• 2 RJ45 connectors on a one WAN cable

  - by mr_stavo

  Hello, I encountered strange setup on a network at company where I do some work. They have internet connection from small ISP located in the same building, all I see is one CAT5 cable with 2 RJ45 connectors. One is going to WAN port on the router and another into LAN port on the same router. This is the only way for internet connection to work. I tried to connect my laptop to one of the RJ45 but it won't work. Now, what is the purpose for such setup?

  Read the article

• How can I use a CanoScan N640Pex scanner over a USB/parallel cable?

  - by detly

  I have an old CanoScan N640Pex flat bed scanner and a USB-to-parallel port cable through which I can connect it to my PC. Unfortunately neither Simple Scan nor XSane detect the scanner. I'm running Ubuntu 12.04 (plus updates and backports) with kernel 3.2.0-31-generic. dmesg tells me this when I plus the cable in: [256411.641910] usb 7-1: new full-speed USB device number 10 using uhci_hcd [256411.872392] usblp0: USB Bidirectional printer dev 10 if 0 alt 1 proto 2 vid 0x067B pid 0x2305 [256411.872417] usbcore: registered new interface driver usblp lsusb shows this device for my cable: Bus 007 Device 010: ID 067b:2305 Prolific Technology, Inc. PL2305 Parallel Port The device node created is /dev/usb/lp0 crw-rw---- 1 root lp 180, 0 Sep 9 17:46 /dev/usb/lp0 There is no extra information from any of these commands when I attach the scanner to the cable and power it on, though. I suspect I might need to change something in /etc/sane.d/canon_pp.conf, but I have no idea what to put for the ieee1284 line, since there is pretty much zero documentation for that parameter. So how can I get it to work?

  Read the article

• Network Management Cable Labeling Techniques and their alternatives [closed]

  - by Alex

  Possible Duplicate: What is the most effective solution you used to label cables? Yes i know there are a lot of howtos and already answered questions about this topic, like this one: How do you organise the cables in your racks? Currently i am searching the web for different techniques (alternatives) for labeling the cables at the server racks and/or data centers. Unfortunately i do not have any experience with labeling/documentation of network cables in a large scale. As far as I could lookup by now the current labeling techniques are coloring and a self defined print-labeling technique (numbering, text) maybe also according to a standard which are usually used. I want to know if QR, RFID (ok RFID in a data center would be stupid due to the radio frequency wouldn't it be?), Barcodes or similar (??) have already been used by some administrators or why they did not consider such techniques at all? Too complicated (with QR scanner etc..) if you are in front of the cables and want to get quick feedback for what the cable is? What alternatives are out there? Advantages/Disadvantages? Best-Practice? I would appreciate any help on this topic, thank you! Regards, Alex

  Read the article

• Acronis Disk Director AFTER Clone Disk error: PXE-E61: Media test failure, check cable

  - by Kairan

  Used Acronis Disk Director on my desktop, plugged in the laptop drive 240GB SSD (USB) and the new hard drive 500GB SSD (usb) and the copy seemed to be fine. I didnt see any error messages but I didnt stare at it for 3 hours either. The clone disk of course the Toshiba hidden restore partition, the primary partition C drive and the active (boot?) partition and yes, did check box for copy NT signature. The computer boots up fine most of the time, but it seems that when the computer goes to sleep (i believe its sleep, hard to do much testing during school) or hibernate or reboot it will sometimes display this message: Intel(R) Boot Agent GE v1.3.52 Copyright (C) 1997-2010, Intel Corporation PXE-E61: Media test failure, check cable PXE-M0F: Exiting Intel Boot Agent Insert system disk in drive. Press any key when ready... Of course any key does nothing but repeat a similar method. However, if I press the power button on the laptop (Toshiba Portege R705, Win 7 Pro 64-bit) it puts computer into hibernate. After hibernating I press power button again and it comes out of hibernation without any odd messages or problems described above... so apparently that is my TEMP fix. Another recent issue I noticed is on occasion when creating a new folder or modifying something in the system variables, other random areas I will get a message: "The Stub received bad data" and simply retry the task and it works. Perhaps these two issues are linked.

  Read the article

• printing parallel over ethernet cable

  - by Crudler

  I have a bit of an interesting challenge :) I have a machine with a parallel printer output, i want it to be able to print instead to a printer in a different room and i know that parallel isnt great over big distances. i found this: http://www.amazon.com/over-Cat5-Extension-Cable-Adapter/dp/B002WJ9S6Y%3FSubscriptionId%3DAKIAINHICTCYYZGJWT4Q%26tag%3Dusbprintercables.net-20%26linkCode%3Dxm2%26camp%3D2025%26creative%3D165953%26creativeASIN%3DB002WJ9S6Y which will let me connect over cat5, but its usb to cat 5. my machine can only output on parallel (its not a computer) so what i was thinking of getting is a parallel(f) to usb and usb to parallel (M) for either side i.e. machine - parallel - usb - cat5 - usb - parallel -printer just seems a bit messy :) suggestions? another thing i would like to try is to get rid of the old school parallel printer and instead use a network based multi function. would this be possible? i.e. machine - parallel -usb - cat5 - ethernet print server - network printer this might be rougher because the machine cannot "know" that we are using a network printer. it can ONLY print to LPT1 Thanks!

  Read the article

• Ethernet cable unplugged after updating from windows 8.0 to 8.1

  - by Pehmolelu

  Yeah, so I went and updated my windows 8 pro to 8.1. Now everything else seems to work but the network. The Ethernet just says that Network cable is unplugged, even though it is plugged and I have tried different cord as well and I have tested that the router works. I have tried uninstalling the network drivers (Realtec PCIe GBE) and reinstall them with no success. After installing drivers the Device Management gives error for it "Device could not be started. Code 10" Before 8.1 update I had rt630x64.inf, after update it was netrt630x64.inf, and after installing the latest driver rt630x64.inf. With rt630x64.inf there isn't any error, but it's still not just working. New downloaded version: 8.020.0815.2013 (From Realtek website) The driver before: 8.1.510.2013 (After updating the windows to 8.1) I'm using Desktop PC, no VM. I dont have VirtualBox or Vmware installed. I have checked from BIOS that the card is enabled. I have booted in safe mode with network enabled. Says unplugged there as well. I have put the power off for few minutes and put back on, no effect. If anyone has any kind of suggestions, please tell.

  Read the article

• Short USB cables not charging?

  - by tropolite

  I find this a strange problem but I can't find anything online about it. Recently I purchased a few short USB cables (20-30cm), to use in my car's USB connector to charge my phone. Strangely an older longer USB cable (1.2m), charges the phone fine (and the icon changes to show charging). With any of the short cables in the same USB slot no charging happens. Both the long and the short cables are USB2 compatible. I naturally assumed the short cables were faulty but connecting them to a PC or connecting to a high capacity external battery charging is successful using all the short cables and longer cables. Hopefully someone here is able to give me an explanation of the problem and how I can overcome this and use a short cable where it is most appropriate. Thanks

  Read the article

• Laptop not charging when connected to mains outlet

  - by Josh

  I've had this laptop for a few weeks now, it's a Sony Vaio. I went to charge it a few days ago and plugged in the power cable, but it's not charging. The battery icon in the Windows taskbar to the bottom right says it's plugged in and charging, but the charge level never goes above 2%. I have checked and I don't have a hcarging switch on the laptop anywhere, so it should be charging. If I unplug the cable, the laptop runs out of power within 30 seconds or so, further fueling my thought that it's a faulty battery. Anyone have any bright ideas? If this doesn't get fixed I'll just ring up Sony and get them to send me a replacement battery or something. Thanks.

  Read the article

• Resetting root password on Fedora Core 3 - serial cable access only

  - by Sensible Eddie

  A little background: We have an old rackmount server running a customised version of Fedora, manufactured by a company called Navaho. The server is a TeamCAT, running some proprietary rubbish called Freedom2. We have to keep it going - the alternative is extraordinarily expensive, and the business is not likely to be running much longer to justify changing things. Through one means or another, it has fallen upon me to try and resolve our lack of root access. The previous admin has fallen under the proverbial bus, and nobody has any clue. We have no access to the root account for this server. ssh is running on the server, and there is one account admin that we can login with, however it has no permission to do anything (ironic...) The only other way into the server is with a null-modem serial cable. This works... up to a point. I can see the BIOS, I can see the post BIOS screen, and then I see "Starting grub", followed by another screen with about four lines of Linux information, but then it stops at that point. The server continues booting, and all services come online after around two minutes, but the serial terminal displays no more information. I understand it is possible to put Linux into "single user mode" to reset a root password, but I have no idea how to do this beyond trying to interrupt it at the grub stage listed above. When I have tried it just froze. It was almost like grub had appeared (since the server did not continue booting) but I couldn't see it on the serial terminal. Which made me think maybe the grub screen has some different serial settings? I don't know... it's the first time I've ever used serial for access! A friend of mine suggested trying to use a Fedora boot CD. We could boot from USB, so something along this approach is possible but again we still can only see what's going on with the serial terminal, so it might not be achievable. Does anyone have any suggestions for things I can try? I appreciate this is a bit of a long shot, but any assistance would be invaluable. *UPDATE 1 - 28/8/12 * - we will be making some attempts on this today and will post further details later!

  Read the article

• DHCP not responding from laptop or router, but works on directly plugged PC?

  - by Matt H

  I'm at my sister in law's place in Singapore. I'm not from Singapore but am here for a few months. She has some sort of cable modem made by motorolla (SB5101 Surfboard). I think it goes, through starhub or similar provider. Anyhow, her PC is directly attached by cable (not wireless) and she can access the internet. There is no wireless router connected to it. The PC is configured with DHCP and appears to be working. However, the moment I unplug her PC and plug in my laptop, it doesn't get an address. The interesting thing here is that I also see this toredo tunnel adaptor etc. I'm not familiar with what that is. It appears to be being assigned an IP v6 address and an IP v4 address. I thought perhaps it's my laptop, but also when I plug in my DDWRT based router, it also fails to get a DHCP assigned address on the WAN port. I can't also seem to connect into any web configuration on the motorolla modem either. Any ideas? what kind of setup is this? all I'd like to do is plug in my wireless router so I can roam around the house and also access the internet.

  Read the article

• So who decided VGA cables should be symetrical ? [closed]

  - by mgb

  < rant So who decided that VGA cables should be the same gender connector at both ends? I just spent an hour trying to fix a server that would apparently boot but wouldn't display any post messages - I needed to change some bios settings. The monitor gives me a helpful error message - "unable to display this resolution". Wondering how it can't show simple VGA res, I reset the bios, when that doesn't work I remove the BIOS battery. The system is in a rack with a keyboard and monitor mounted 6ft away - with the cable running through the normal waist thick rats nest of wiring of wiring. The monitor worked with another system, so it and the VGA cable are good, I brought in another monitor and tried that - still nothing. Eventually I ripped the rack apart to discover that the other end of the VGA connector I was trying to plug into the server was actually plugged into another server box ! And the second monitor I was testing was plugged into the first monitor. An error message like - "I'm actualy plugged into another monitor stupid" - would be useful. So would having a connector with a male end and a female end. < end rant - thank you

  Read the article

• Why isn't my phone charging with some micro usb cables?

  - by Jacxel

  I ordered 3 microUSB cables over ebay. My phone was at about 50% battery and I wanted to use it as a hot spot for some browsing on my laptop, so I plugged it in, a charging icon appeared on the phone, my laptop showed it as a connected usb device and so I went about my business. About 30 minutes later I checked the phone and to my dismay saw 45% battery. But ahh, I thought, I have been putting the poor little thing under too much pressure, acting as a WiFi hotspot must drain the battery quicker than it can charge via usb, perhaps even using my laptops usb port wouldn't output enough power. Unscathed I continued on and when I was going to bed I plugged the usb cable into a mains adapter and switched everything battery consuming off and content, went to sleep. The next morning I was awoken by my phones alarm which got cut off unexpectedly. I attempted to unlock my phone which showed no more signs of life. Why isn't my phone charging with these new USB cables? For clarity: They transfer data with no problems The phone appears to be charging, showing all the signs and lights it normally would, the cable that came with the phone works as you would expect, so its not a fault with the phone, I think they slow the discharging of the phone, but I could be wrong. Are these just bad quality cables? Is there a way to fix this issue?

  Read the article

• Networking two computers running Windows XP [closed]

  - by user38100

  Possible Duplicate: Setting up a LAN connection in Windows How can I connect two computers, both running Windows XP, to each other using a single LAN cable?

  Read the article

• Wireless vs. Wired: which is faster?

  - by studiohack

  I have the option of hooking up my machines to the internet either wirelessly or via ethernet cable (wired). I'm curious as to which is faster; the approximate wireless signal strength (average) is about 60%. My question is, would my internet be faster if I used ethernet, resulting in a stronger connection?

  Read the article

• Multiple Audio I/P and O/P simultaneaously

  - by Raj Naveen

  hi (1) i saw in one of your posts that it is possible to get different outputs in windows 7. i am eager to know more. Is there any way i can create a 2 or more virtual cable between two softwares simultaneously. so that simultaneously, two or more audio inputs will be routed to equal no of audio analysers receivers, and then the audio analysers send back a filtered audio back to respective audio inputs... Please reply to email id: [email protected]

  Read the article

• I cannot stay logged in to a site with my router

  - by Luke101

  I have a D-Link home router and my isp is Time warner. When I try to login to any site it does not let me. The website does not keep me logged in when I navigate the pages. I have to keep loging in for every web page I see. When I connect my cable modem directly to my computer I am able to stay logged in. Any ideas here?

  Read the article

• What is this very short power cable called?

  - by Portman

  I have a couple of networking components in my rack that take giant AC adapters ("power bricks") that don't fit neatly into my rackmount PDU. I have one "thingy" that is shown below, and I need to buy a few more. But I have no idea what I'm searching for because I don't know what the "thingy" is called. Yes, this drawing is terrible. I would ask my 4-year-old to draw it for me because she's a better artist, but she's taking a nap.

  Read the article

• Connecting Windows XP to Windows 7 directly using cable

  - by TPR

  These are the problems I am encountering. XP can access Windows 7, not the other way around (which is fine, because I don't need it the other way currently) File transfer is too slow like 0.031 MB/s even though netperf and netCPS list around 8-9 MB/s. I disabled firewall on both computers. Both are same workgroup. I left homegroup on Windows 7. Windows 7 sees the connection as unidentified network. 10.1.1.2 (XP) and 10.1.1.1 (Windows 7) Subnet mask 255.255.255.0 Default gateway and DNS are empty for both of them. Both computer are connected to internet using wireless (using home network), and both of them are connected to each other using wire! If anybody has any pointers, do let me know. I have no problem doing such setup with both computers being Windows 7. This time one of them is XP though, and that seems to be the problem.

  Read the article

• connect 2 computers without crossover cable

  - by Infestor

  connecting two computers with straight cat5e, is this possible at all?

  Read the article

< Previous Page | 4 5 6 7 8 9 10 11 12 13 14 15  | Next Page >