Search Results

Search found 3293 results on 132 pages for 'comodo firewall'.

Page 83/132 | < Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >

  • Get OWA and ActiveSync working on server using HTTP redirect in IIS 7

    - by eric
    We have two servers on our LAN. One is a Windows 2003 Server domain controller running Exchange 2003. The other is a stand-alone Windows 2008 server running IIS 7. Our company website runs on the IIS 7 (2008) server, so the firewall forwards port 80 to this. How can I get OWA and ActiveSync to work with this setup? And without using SSL. I have tried setting up a website on the IIS 7 box (mail.ourdomain.com) and using HTTP redirect to point to http://mailserver/exchange, but this doesn't work. Do we have to purchase an SSL certificate for this to work?

    Read the article

  • cannot access my own computer through My Network Places

    - by vgv8
    My home Windows XP Pro SP3 machine is DHCP client receiving configurations from ISP. Trying to access in WindowsExplorer -My Network Places - Microsoft Windows Network shows Workgroup with a delay of 3 min and then popups messagebox: Microsoft Windows Network Workgroup is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions.The list of servers for this workgroup is not currently available OK I am logged-in as local machine Administrator. The internet is accessible (I am writing this post through it) The Firewall is disabled The "Computer Bowser" and all networking services, I could find, are running Control Panel -- Network Connections -- Properties (of connection) --- Internet Protocol (TCP/IP), btn Properties --- --- tab General, btn "Advanced..." -- tab WINS-- rbtn "Enable NetBIOS over TCP/IP" checked Why cannot I access my own PC (and shares on it) through My Network Places What is the possible problem? How to daignose the problem?

    Read the article

  • CA and VPN setup

    - by Raj
    We are a small comany about 20 employees. We have some off site some i houser servers. Where should I install CA? On a domain controller or VM? can I obtain my own certificate for MS VPN? Where should I install MS vpn server? can I install on VM CA server? Do I need to open any ports on Firewall? Please send me or direct me to a web site where I can get setip by step installation instructions. Thanks.

    Read the article

  • mod_proxy failing as forward proxy in simple configuration

    - by Stabledog
    (On Mac OS X 10.6, Apache 2.2.11) Following the oft-repeated googled advice, I've set up mod_proxy on my Mac to act as a forward proxy for http requests. My httpd.conf contains this: <IfModule mod_proxy> ProxyRequests On ProxyVia On <Proxy *> Allow from all </Proxy> (Yes, I realize that's not ideal, but I'm behind a firewall trying to figure out why the thing doesn't work at all) So, when I point my browser's proxy settings to the local server (ip_address:80), here's what happens: I browse to http://www.cnn.com I see via sniffer that this is sent to Apache on the Mac Apache responds with its default home page ("It works!" is all this page says) So... Apache is not doing as expected -- it is not forwarding my browser's request out onto the Internet to cnn. Nothing in the logfile indicates an error or problem, and Apache returns a 200 header to the browser. Clearly there is some very basic configuration step I'm not understanding... but what?

    Read the article

  • UFW: force traffic thru OpenVPN tunnel / do not leak any traffic

    - by hotzen
    I have VPN access using OpenVPN and try to create a safe machine that does not leak traffic over non-VPN interfaces. Using the firewall UFW I try to achieve the following: Allow Access from LAN to the machine's web-interface Otherwise only allow Traffic on tun0 (OpenVPN-Tunnel interface when established) Reject (or forward?) any traffic over other interfaces Currently I am using the following rules (sudo ufw status): To Action From -- ------ ---- 192.168.42.11 9999/tcp ALLOW Anywhere # allow web-interface Anywhere on tun0 ALLOW Anywhere # out only thru tun0 Anywhere ALLOW OUT Anywhere on tun0 # in only thru tun0 My problem is that the machine is initially not able to establish the OpenVPN-connection since only tun0 is allowed, which is not yet established (chicken-egg-problem) How do I allow creating the OpenVPN connection and from this point onward force every single packet to go thru the VPN-tunnel?

    Read the article

  • Apache on Win32: Slow Transfers of single, static files in HTTP, fast in HTTPS

    - by Michael Lackner
    I have a weird problem with Apache 2.2.15 on Windows 2000 Server SP4. Basically, I am trying to serve larger static files, images, videos etc. The download seems to be capped at around 550kB/s even over 100Mbit LAN. I tried other protocols (FTP/FTPS/FTP+ES/SCP/SMB), and they are all in the multi-megabyte range. The strangest thing is that, when using Apache with HTTPS instead of HTTP, it serves very fast, around 2.7MByte/s! I also tried the AnalogX SimpleWWW server just to test the plain HTTP speed of it, and it gave me a healthy 3.3Mbyte/s. I am at a total loss here. I searched the web, and tried to change the following Apache configuration directives in httpd.conf, one at a time, mostly to no avail at all: SendBufferSize 1048576 #(tried multiples of that too, up to 100Mbytes) EnableSendfile Off #(minor performance boost) EnableMMAP Off Win32DisableAcceptEx HostnameLookups Off #(default) I also tried to tune the following registry parameters, setting their values to 4194304 in decimal (they are REG_DWORD), and rebooting afterwards: HKLM\SYSTEM\CurrentControlSet\Services\AFD\Parameters\DefaultReceiveWindow HKLM\SYSTEM\CurrentControlSet\Services\AFD\Parameters\DefaultSendWindow Additionally, I tried to install mod_bw, which sets the event timer precision to 1ms, and allows for bandwidth throttling. According to some people it boosts static file serving performance when set to unlimited bandwidth for everybody. Unfortunately, it did nothing for me. So: AnalogX HTTP: 3300kB/s Gene6 FTPD, plain: 3500kB/s Gene6 FTPD, Implicit and Explicit SSL, AES256 Cipher: 1800-2000kB/s freeSSHD: 1100kB/s SMB shared folder: about 3000kB/s Apache HTTP, plain: 550kB/s Apache HTTPS: 2700kB/s Clients that were used in the bandwidth testing: Internet Explorer 8 (HTTP, HTTPS) Firefox 8 (HTTP, HTTPS) Chrome 13 (HTTP, HTTPS) Opera 11.60 (HTTP, HTTPS) wget under CygWin (HTTP, HTTPS) FileZilla (FTP, FTPS, FTP+ES, SFTP) Windows Explorer (SMB) Generally, transfer speeds are not too high, but that's because the server machine is an old quad Pentium Pro 200MHz machine with 2GB RAM. However, I would like Apache to serve at at least 2Mbyte/s instead of 550kB/s, and that already works with HTTPS easily, so I fail to see why plain HTTP is so crippled. I am using a Kerio Winroute Firewall, but no Throttling and no special filters peeking into HTTP traffic, just the plain Firewall functionality for blocking/allowing connections. The Apache error.log (Loglevel info) shows no warnings, no errors. Also nothing strange to be seen in access.log. I have already stripped down my httpd.conf to the bare minimum just to make sure nothing is interfering, but that didn't help either. If you have any idea, help would be greatly appreciated, since I am totally out of ideas! Thanks! Edit: I have now tried a newer Apache 2.2.21 to see if it makes any difference. However, the behaviour is exactly the same. Edit 2: KM01 has requested a sniff on the HTTP headers, so here comes the LiveHTTPHeaders output (an extension to Firefox). The Output is generated on downloading a single file called "elephantsdream_source.264", which is an H.264/AVC elementary video stream under an Open Source license. I have taken the freedom to edit the URL, removing folders and changing the actual servers domain name to www.mydomain.com. Here it is: LiveHTTPHeaders, Plain HTTP: http://www.mydomain.com/elephantsdream_source.264 GET /elephantsdream_source.264 HTTP/1.1 Host: www.mydomain.com User-Agent: Mozilla/5.0 (Windows NT 5.2; WOW64; rv:6.0.2) Gecko/20100101 Firefox/6.0.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: de-de,de;q=0.8,en-us;q=0.5,en;q=0.3 Accept-Encoding: gzip, deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Connection: keep-alive HTTP/1.1 200 OK Date: Wed, 21 Dec 2011 20:55:16 GMT Server: Apache/2.2.21 (Win32) mod_ssl/2.2.21 OpenSSL/0.9.8r PHP/5.2.17 Last-Modified: Thu, 28 Oct 2010 20:20:09 GMT Etag: "c000000013fa5-29cf10e9-493b311889d3c" Accept-Ranges: bytes Content-Length: 701436137 Keep-Alive: timeout=15, max=100 Connection: Keep-Alive Content-Type: text/plain LiveHTTPHeaders, HTTPS: https://www.mydomain.com/elephantsdream_source.264 GET /elephantsdream_source.264 HTTP/1.1 Host: www.mydomain.com User-Agent: Mozilla/5.0 (Windows NT 5.2; WOW64; rv:6.0.2) Gecko/20100101 Firefox/6.0.2 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: de-de,de;q=0.8,en-us;q=0.5,en;q=0.3 Accept-Encoding: gzip, deflate Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.7 Connection: keep-alive HTTP/1.1 200 OK Date: Wed, 21 Dec 2011 20:56:57 GMT Server: Apache/2.2.21 (Win32) mod_ssl/2.2.21 OpenSSL/0.9.8r PHP/5.2.17 Last-Modified: Thu, 28 Oct 2010 20:20:09 GMT Etag: "c000000013fa5-29cf10e9-493b311889d3c" Accept-Ranges: bytes Content-Length: 701436137 Keep-Alive: timeout=15, max=100 Connection: Keep-Alive Content-Type: text/plain

    Read the article

  • IPTables masquerading with one NIC

    - by Tuinslak
    Hi, I am running an OpenVPN server with only one NIC. This is my current layout: public.ip > Cisco firewall > lan.ip > OpenVPN server lan.ip = 192.168.22.70 The Cisco firewall forwards the requests to the oVPN server, thus so far everything works and clients are able to connect. However, all clients connected should be able to access 3 networks: lan1: 192.168.200.0 (vpn lan) > tun0 lan2: 192.168.110.0 (office lan) > eth1 (gw 192.168.22.1) lan3: 192.168.22.0 (server lan) > eth1 (broadcast network) So tun0 is mapped to eth1. Iptables output: # iptables-save # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *filter :INPUT ACCEPT [327:26098] :FORWARD DROP [305:31700] :OUTPUT ACCEPT [291:27378] -A INPUT -i lo -j ACCEPT -A INPUT -i tun0 -j ACCEPT -A INPUT -i ! tun0 -p udp -m udp --dport 67 -j REJECT --reject-with icmp-port-unreachable -A INPUT -i ! tun0 -p udp -m udp --dport 53 -j REJECT --reject-with icmp-port-unreachable -A FORWARD -d 192.168.200.0/24 -i tun0 -j DROP -A FORWARD -s 192.168.200.0/24 -i tun0 -j ACCEPT -A FORWARD -d 192.168.200.0/24 -i eth1 -j ACCEPT COMMIT # Completed on Wed Feb 16 14:14:20 2011 # Generated by iptables-save v1.4.2 on Wed Feb 16 14:14:20 2011 *nat :PREROUTING ACCEPT [302:26000] :POSTROUTING ACCEPT [3:377] :OUTPUT ACCEPT [49:3885] -A POSTROUTING -o eth1 -j MASQUERADE COMMIT # Completed on Wed Feb 16 14:14:20 2011 Yet, clients are unable to ping any ip (including 192.168.200.1, which is the oVPN's IP) When the machine was directly connected to the internet, with 2 NICs, it was quite simply solved with masquerading and adding static routes in the oVPN client's config. However, as masquerading won't accept virtual interfaces (eth0:0, etc) I am unable to get masquerading to work again (and I'm not even sure whether I need virtual interfaces). Thanks. Edit: OpenVPN server: # ifconfig eth1 Link encap:Ethernet HWaddr ba:e6:64:ec:57:ac inet addr:192.168.22.70 Bcast:192.168.22.255 Mask:255.255.255.0 inet6 addr: fe80::b8e6:64ff:feec:57ac/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6857 errors:0 dropped:0 overruns:0 frame:0 TX packets:4044 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:584046 (570.3 KiB) TX bytes:473691 (462.5 KiB) Interrupt:14 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:334 errors:0 dropped:0 overruns:0 frame:0 TX packets:334 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:33773 (32.9 KiB) TX bytes:33773 (32.9 KiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.1 P-t-P:192.168.200.2 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) ifconfig on a client: # ifconfig eth0 Link encap:Ethernet HWaddr 00:22:64:71:11:56 inet addr:192.168.110.94 Bcast:192.168.110.255 Mask:255.255.255.0 inet6 addr: fe80::222:64ff:fe71:1156/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:3466 errors:0 dropped:0 overruns:0 frame:0 TX packets:1838 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:997924 (974.5 KiB) TX bytes:332406 (324.6 KiB) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:37847 errors:0 dropped:0 overruns:0 frame:0 TX packets:37847 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2922444 (2.7 MiB) TX bytes:2922444 (2.7 MiB) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.200.30 P-t-P:192.168.200.29 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:689 errors:0 dropped:18 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:468778 (457.7 KiB) wlan0 Link encap:Ethernet HWaddr 00:16:ea:db:ae:86 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:704699 errors:0 dropped:0 overruns:0 frame:0 TX packets:730176 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:520385963 (496.2 MiB) TX bytes:225210422 (214.7 MiB) static routes line at the end of the client's config (I've been playing around with the 192.168.200.0 -- (un)commenting to see if anything changes): route 192.168.200.0 255.255.255.0 route 192.168.110.0 255.255.255.0 route 192.168.22.0 255.255.255.0 route on a vpn client: # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.200.29 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.22.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.200.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 192.168.200.29 255.255.255.0 UG 0 0 0 tun0 192.168.110.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.110.1 0.0.0.0 UG 0 0 0 eth0 edit: Weirdly enough, if I set push "redirect-gateway def1" in the server config, (and thus routes all traffic through VPN, which is not what I want), it seems to work.

    Read the article

  • Virus blocking incoming connections ?

    - by Benoît
    Hello, on my windows 2003 server, all incoming connections are dropped. I can see them getting in using Wireshark, but even a single ping from another computer fails. All locally initiated connection work fine (i'm asking from the server). This server is the DC/DHCP/DNS/File server, so computer clients are in the dark. I've run varius antivirus and removal tools without any luck. The Windows Firewall is disabled. I'm wild-guessing at some virus/worm. How can i check why these incoming ICMP/TCP SYN/etc are dropped ? Anyone has any knowledge about such situations ? Thanks.

    Read the article

  • IP assignment in a /28 block

    - by mks
    Need help on setting up firewall router. My config is as below: Public static network ID: x.x.x.48/28 gateway: x.x.x.49 available IP for the hosts: x.x.x.52 to 62 gw_eth0 <-- fw_eth0 - fw_eth1 <-- dmz_switch Four servers are connected on dmz_switch (say s1, s2, s3, s4) all have to use public static IP address from the above block. Any recommendation on IP assignment and route setup? Do I need to subnet the above block further or simply use /32 netmask and point-to-point static routes in the above setup?

    Read the article

  • Can I set up a 2nd home wireless router, with router2 connecting to the internet through a desktop which is wirelessly connected to router1?

    - by gil b.
    Hi, I apologize for the crudeness of my MSPaint drawing, but please view my diagram of what I'd like to accomplish: Proposed home network architecture Currently, all devices are connected to 1 wireless router. I would like to make my own subnet, with a box in-between my subnet and the shared wireless router, so that I can learn about IDS, traffic analysis, etc. I was also given a cisco PIX firewall to play around with, and it'd be an added bonus if I could incorporate that into my network. The reason for this proposed architecture is so that I can monitor all MY traffic, without seeing anything going on with my roommates' traffic. my MAIN Question is, is it possible to have my desktop connect to the wireless router with internet via wireless card AND share that connection via the ethernet card, hooked to wireless router 2? cable modem - wireless router - desktop pc connected wirelessly - wireless router 2 getting internet from wired connection to desktop pc - laptops connected wirelessly The PIX can be left out for now, but I'm wondering if it could eventually be incorporated? THANKS!

    Read the article

  • What is the method to reset the Planar 1910m monitor?

    - by Richard J Foster
    My monitor (a Planar, apparently model number PL1910M) is not working. (It is flashing a green / orange sequence which I believe to be an error code. The sequence, in case it helps consists of orange and green three times quickly followed by a longer orange, then another green followed by a long period where both colors appear to be present). I vaguely recall a co-worker suffering from a similar problem, and our IT department "resetting" the monitor by holding down a certain set of keys as they apply power. Unfortunately, I do not remember what that key sequence was, our IT department is not responding, and the Planar web site is blocked by the content filtering firewall we have in place! What is the sequence to perform the reset? (For bonus geek-credit, what does the code mean... as if it indicates a blown component clearly a reset will not help me. ;-))

    Read the article

  • How to get two seperate remote domain controllers with same IP to work?

    - by Mr. Mister
    Hi, I have a VPN setup between multiple locations. Between each location and the central point (me), is a trust between our domain controllers. It all works great.. A new location wants to join, but their AD controller is using an IP address that is already in use by another AD in a separate location. Neither locations can change their IP addresses, but apparently there is a NAT rule that could be used to allow communication between each AD controller? The central site has a Cisco 5510 firewall which could perform the NAT, but I am unsure of the logic behind the NAT rule. Is anyone able to explain or help out? Thanks.

    Read the article

  • Issues with FTP on my server

    - by homestead
    I installed FTP on my windows 2003 box I created a FTP site on a ipaddress, I am not allowing anonymous access. I created a user that has access to the folder c:\ftptest connecting to my server using filezilla shows: connectiong to -0.0.0.0 connection established, waiting for welcome message could not connect to server I tried both active and passive modes. The port on the server is open i.e. TCP 21 I can connect to other FTP sites so my locla firewall isnt' the issue. (now I know why sys admin work is so fun!)

    Read the article

  • Detect damage done by virus

    - by user38471
    Hey, this morning after I went to college a virus infected my pc without any user interaction at my end. When I came home my computer was completely frozen and infected with lots of trojans. I have not typed anything important since returning so keys cannot be logged. However I want to know exactly when my computer crashed from the time of infection to see what could potentially be done remotely by a hacker. The virus my pc was diagonosed with was "fakespypro" http://www.microsoft.com/security/portal/Threat/Encyclopedia/Entry.aspx?Name=Win32%2fFakeSpypro on a fully updated windows 7 installation with firewall enabled. My computer was connected to an internal dorm room network, so probably that has had to do something with it. Any further information about how I could backtrace this virus infection or ways to discover what data might be stolen would be greatly appriciated.

    Read the article

  • Making internal website available publicly (Win 2008 Server)

    - by endigo
    I have an IIS 7 web site that is running on a Windows 2008 Server (64-bit) VMWare on a Windows 2008 Server (64-bit) Host on my local network. My router is a Firebox XEdge and it has port 80 directed to the IP of the server on VMWare. I can reach the web site from inside the network, but I cannot reach the site from outside the network. I have other web sites that are working through the Firebox, and I am confident that it is configured correctly. I suspect that Windows 2008 server is blocking routed or public addresses, but I have shut down the firewall on the Server that is running on VMWare and the AVG Anti-virus to no avail. How can I make my site available publicly.

    Read the article

  • What equipment do real ISP's use?

    - by Allanrbo
    In a dormitory of 550 residents, people often mistakenly set up DHCP servers for the whole network by plugging in their private Wi-Fi routers wrongly. Also recently, someone mistakenly configured their PC to a static IP being the same as that of the default gateway. We use cheap 3Com switches at the moment. I know that Cisco switches support DHCP snooping to solve the DHCP problem, but that still does not solve the default gateway IP takeover problem. What sort of switch equipment do real ISP's use so their customers cannot break the network for the other customers? What we ended up doing In case anyone are courious, we ended up doing seperate VLANs for each user. And as a matter of fact, not just the 550 users, but for 2500 users (11 dorms). Here's a page describing the setup: http://k-net.dk/technicalsetup/ (the section "Transparent firewall using VLANs"). There was no significant load on the router server as I feared in one of the comments below. Even at 800Mpbs.

    Read the article

  • SSH Tunnel for Remote Desktop via Intermediary Server

    - by Mihai Todor
    I've seen many examples of SSH tunnels on the nets, but I'm still having no luck with this. Here's the setup: Windows 7 PC in a private network, sitting behind a firewall, with PowerShellInsider SSH server set up and working fine. Public access Linux server, which has access to the PC. Windows 7 laptop, at home, from which I wish to do remote desktop on the PC. Now, here's what I've tried so far: SSH tunnel from my laptop to the Linux server: ssh -f my_user@LINUX_SERVER -L 6666:LINUX_SERVER_IP:6666 -N SSH to the Linux server where I've set up a tunnel to the PC: ssh -f 'PRIVATE_DOMAIN\my_user'@PC_NAME -L 6666:PC_IP:3389 -N Unfortunately, I must be doing something wrong, because it doesn't seem to work. Any ideas why or, at least, any suggestions on how can I try to debug this setup? At the moment, I have access to all 3 machines (non-root on Linux), so I can test whatever I want...

    Read the article

  • other computer in the network cannot connect to mysql database

    - by user28233
    I have a vb.net program that uses mysql as its database. And it works when the computer has wampservr installed. But the program gets an unhandled exception error when the computer where its running does not have a wampserver. The only thing that is installed in it is the mysql connector net. How do I make it work. I just want the two programs to access the same mysql database. I already opened port 20 by configuring firewall. Both in TCP and UDP. What do I do? Do I have to tweak the codes? Anyone in here who have tried this before?

    Read the article

  • other computer in the network cannot connect to mysql database

    - by user23950
    I have a vb.net program that uses mysql as its database. And it works when the computer has wampservr installed. But the program gets an unhandled exception error when the computer where its running does not have a wampserver. The only thing that is installed in it is the mysql connector net. How do I make it work. I just want the two programs to access the same mysql database. I already opened port 20 by configuring firewall. Both in TCP and UDP. What do I do? Do I have to tweak the codes? Anyone in here who have tried this before?

    Read the article

  • MySQL port 3306 became filtered when configured with Keepalived on Ubuntu server 12.04 lts

    - by Ludwig
    I'm configuring two load balancer (lb01 & lb02) with keepalived for my two mysql server (db01 & db02) with standard port 3306. There is virtual ip address (192.168.205.10) to access it also act as failover, but somehow the web server in the front can't access this mysql server using vip. Here is my config: Keepalived: Only the mysql part that i added here. LB01: virtual_server 192.168.205.10 3306 { delay_loop 6 lb_algo rr lb_kind DR protocol TCP real_server 192.168.205.4 3306 { weight 10 TCP_CHECK { connect_port 3306 connect_timeout 2 } } } LB02: virtual_server 192.168.205.10 3306 { delay_loop 6 lb_algo rr lb_kind DR protocol TCP real_server 192.168.205.6 3306 { weight 10 TCP_CHECK { connect_port 3306 connect_timeout 2 } } } I already comment out the "bind-address=127.0.0.1" part in both server my.cnf. Also, remove all the firewall prog from my ubuntu server (ufw or iptables). Any help? thanks.

    Read the article

  • In TCP/IP terms, how does a download speed limiter in an office work?

    - by TessellatingHeckler
    Assume an office of people, they want to limit HTTP downloads to a max of 40% bandwidth of their internet connection speed so that it doesn't block other traffic. We say "it's not supported in your firewall", and they say the inevitable line "we used to be able to do it with our Netgear/DLink/DrayTek". Thinking about it, a download is like this: HTTP GET request Server sends file data as TCP packets Client acknowledges receipt of TCP packets Repeat until download finished. The speed is determined by how fast the server sends data to you, and how fast you acknowledge it. So, to limit download speed, you have two choices: 1) Instruct the server to send data to you more slowly - and I don't think there's any protocol feature to request that in TCP or HTTP. 2) Acknowledge packets more slowly by limiting your upload speed, and also ruin your upload speed. How do devices do this limiting? Is there a standard way?

    Read the article

  • SHH Tunnel for Remote Desktop via Intermediary Server

    - by Mihai Todor
    I've seen many examples of SSH tunnels on the nets, but I'm still having no luck with this. Here's the setup: Windows 7 PC in a private network, sitting behind a firewall, with PowerShellInsider SSH server set up and working fine. Public access Linux server, which has access to the PC. Windows 7 laptop, at home, from which I wish to do remote desktop on the PC. Now, here's what I've tried so far: SSH tunnel from my laptop to the Linux server: ssh -f my_user@LINUX_SERVER -L 6666:LINUX_SERVER_IP:6666 -N SSH to the Linux server where I've set up a tunnel to the PC: ssh -f 'PRIVATE_DOMAIN\my_user'@PC_NAME -L 6666:PC_IP:3389 -N Unfortunately, I must be doing something wrong, because it doesn't seem to work. Any ideas why or, at least, any suggestions on how can I try to debug this setup? At the moment, I have access to all 3 machines (non-root on Linux), so I can test whatever I want...

    Read the article

  • webmin not working on port 10000

    - by Ali
    Hi, I posted a similar question yesterday but can't seem to find that post. I have installed webmin on my server which has SSL and its service is running but I am unable to open it in browser. I thought may be the port is blocked by server's firewall so I entered port 10000 (TCP - inbound) in APF but still no luck. When I use https://localhost:10000 on server to access webmin then it works fine but not remotely. Why is such a simple thing so hard to run? Thanks

    Read the article

  • CentOS Existing host to new host with all data/files

    - by ganesh
    Good noon. Our small startup management decided to move our production server from existing provider to azure. We have centOS on both. It is for classified's related site, considerable amount of data and ~thousands users with their disc space quota. This is our first time moving our servers. I need your Guidance and suggestions on these. 1) How to migrate the mysql db (dump OR slave OR copy filesystem)? 2) How to manage the emails during the downtime. 3) Manage the files 4) How to security/Firewall check list for the new system 5) IP/DNS related Checklist 6) Anything that I missed out!. Since first time, planning to be more cautious. Any reference documents Highly appreciated. Thank you all!.

    Read the article

  • How do I configure pfsense as an outbound VPN client?

    - by Avery Chan
    We use pfsense as a router/firewall. Because we're based in China, it is useful for us to have VPN access for all our internal clients. Instead of each individual client connecting to a VPN server stateside, I'd like to configure pfsense as a VPN client and have all the network traffic be routed through it. Most of the posts I've seen regarding pfsense and VPN are concerning connecting to the LAN from outside; this is not what I want to do. Another option would be for an SSH tunnel to be initiated on the pfsense box with the LAN traffic routed through it. How do I configure pfsense to be able to do either of these? One huge caveat is that OpenVPN cannot be used. The solution I am looking for needs to use one of the other VPN protocols.

    Read the article

< Previous Page | 79 80 81 82 83 84 85 86 87 88 89 90  | Next Page >