Search Results

Search found 2629 results on 106 pages for 'idle timer'.

Page 84/106 | < Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >

• CPU operating temperature ranges

  - by osij2is

  I have an AMD Phenom II 960T with 2 cores unlocked for a total of 6 cores. I don't overclock at all. I have a Arctic Cooling ACALP64 Heatsink/Fan installed. I'm currently running ESXi 5.0 so I have to go into the BIOS to read the CPU temperatures, which at idle seem to be in the 71-74C range. To me, this is pretty high, but I cannot find any official temperature ranges that AMD says the CPU can work well within. There seems to be a lot of questions on superuser and numerous forums around CPU temperatures but no one seems to have a clear consensus as to what the manufacturer temperature ranges are for specific CPUs. I've tried searching through AMDs site to no avail. At this point, I'd be willing to shut off the 2 extra cores if it keeps the heat down but until I get some sort of tolerance or range for temperature, I have no idea if the CPU is being damaged or not. Can anyone point to a direct source, article, FAQ from AMD that specifically states their CPUs temperature range? Or are CPU temperature ranges so varying that there's no possible baseline? Am I being too paranoid about this? To me, anything over 65C is a bit much and if I'm in the low-mid 70s range with NO VMs running, what can I expect if I have several VMs running?

  Read the article

• How do I get a network printer installed in ubuntu 9.04?

  - by SoaperGEM

  My girlfriend's work computer now has Linux on one of the partitions, and for the most part it's running fine--except that I can't seem to get the network printers configured right. There are two of them: a Lanier MP 7500/LD275 and a Lanier MP C3000/LD430c, and Linux seems to have found them both automatically. I'll go through the steps of what I did, and what exactly went wrong. I went to Administration Printing, and clicked the new printer button. It searched for printers and found them both, listed under "Network Printers." I added them as new printers in succession. However, when I clicked "Print a Test Page," it failed saying there was a broken pipe. The device URIs were saved as socket://[ip address]:9100. I changed these to lpd://[ip address] per some online tutorial, which at first looked like it might have worked (but didn't). Then when I tried to print a test page, it first said Processing (and sometimes even Processing - printing test page, 4%, but always subsequently displays Idle - /usr/lib/cups/backend/lpd failed. Help! What do I do? It seems like Linux can find these printers just fine, and the drivers seem to be in place, so what's going wrong?

  Read the article

• How to disable monitor "sleep" on Ubuntu without access to X?

  - by exhuma

  I just received a CuBox (basically a tiny ARM based PC). It comes pre-installed with Ubuntu, and I did not (yet) want to fiddle with the OS itself. My aim is to have it automaticall start a browser in fullscrren upon boot. Using chromium with the "--kiosk" flag works perfectly in that regard. But now I have the problem that the screen turns off after a certain time. I managed to turn off the screen saver using: gconftool-2 -s /apps/gnome-screensaver/idle_activation_enabled --type=bool false And tried to turn off the power management using: gconftool-2 -s /apps/gnome-power-manager/ac_sleep_display --type=int 0 and gconftool-2 -s /apps/gnome-power-manager/timeout/sleep_display_ac --type=int 0 Neither of the power-management commands worked. Theoretically I could hook up a mouse and keyboard and configure it manually. But I want to learn how to do it over the console. The box will eventually be only reachable via SSH. So I'd like to be able to trouble-shoot it later. I don't quite know where to look for. I searched the gconf tree using gconftool-2 -S for anything related to the terms power, idle and sleep but did not find anything promising. Maybe it's not even gconf related... Any ideas what else I could look for?

  Read the article

• Many different BSOD

  - by Exa

  I'm experiencing multiple bluescreens for a couple of months now. Their error code is as diverse as their time of occurence... Sometimes it happens during gaming, sometimes when watching videos, sometimes when the computer is idle. These are the bluescreens I see most often: PAGE_FAULT_IN_NONPAGED_AREA KMODE_EXCEPTION_NOT_HANDLED IRQL_NOT_LESS_OR_EQUAL SYSTEM_SERVICE_EXCEPTION SYSTEM_THREAD_EXCEPTION INTERRUPT_EXCEPTION_NOT_HANDLED DRIVER_IRQL_NOT_LESS_OR_EQUAL DRIVER_OVERRAN_STACK_BUFFER Responsible drivers (according to the memory dumps): hal.dll tcpip.sys dxgmms1.sys ndis.sys mouhid.sys atikmdag.sys dump_atapi.sys and of course: ntoskrnl.exe My first thought was a driver incompatibility because I am using Windows 8 and some of the bluescreens seem to come from driver issues. All drivers are up to date. I'm afraid that my memory is broken or the mainboard or both. I used the windows integrated memtest which didn't find any errors. Memtest86 found some errors. Does it make sense to buy new memory? Couldn't it be a problem of the board as well? I also read that my memory could run at a too low voltage. But it's set to 1.5V as recommended. Another guess would be to set the memory's latencies manually, but how do I know which ones to try? Here is a screenshot of bluescreenview showing the latest bluescreens. Maybe someone has faced the same behavior before and found a solution. Any ideas or suggestions? Current setup on which the bluescreens occur. Windows 8 RTM (6.2.9200) Asrock 970 Extreme4 AMD FX-8150 ATI Radeon HD5850 16 GB RAM (DDR3-1800) Latest drivers for all devices

  Read the article

• Slow, choppy video playback with nVidia 8600GT

  - by user5351

  I have an nVidia 8600GT card (made by EVGA) on a machine with Windows Vista (AMD Athlon X2 processors) and four gigs of ram. It runs pretty good, but I have had some slow/choppy/stuterring video playback issues whenever watching flash videos on Youtube or other sites. The problem is there with both Firefox and IE flash videos, but is maybe worse with Firefox. I also tried Linux with nVidia's binary drivers and it was about the same. I downloaded EVGA precision which allows me to control stuff like the fan and clock speed. The card's temp (in both Vista and Linux) is usually at 66C when idle (not playing a game or watching anything). It goes up a little when watching a video (maybe 68-72C). Any ideas on how to fix this? UPDATE: The issues are both with full screen and embedded flash videos. I have Flash 10.0.32.18 (always make sure I use most recent for security), and the CPU is an AMD Athlon 64 X2 Dual Core Processor 4000+ at 2.11 GHZ. The current GPU driver installed is the most recent GeForce one from last July.

  Read the article

• How does one skip “Windows did not shut down successfully” in Win7-64?

  - by XenonofArcticus

  Migrating an app from an expensive and unreliable dedicated embedded x86 box running WinXP-embedded to COTS hardware (Dell E6410 laptop) running normal Win7-64. At this time, it's not feasible to deploy using Windows 7 embedded. The problem is, that the system is still sort of "embedded". The power could shut off at virtually any time without prior warning. We've stripped the OS down and removed the battery capability so that it will power down as desired. The app never writes to the disk, so it's not like we're going to corrupt anything terribly. The system is essentially idle after our app is up and running (with the exception of some computation, graphics, and TCP/IP and serial communications) so the OS enters a pretty stable state rather quickly. After a power-loss however, it rightly complains that Windows did not shut down successfully and presents the user with the Windows Error Recovery text screen. If left alone, it does eventually move on booting just fine, but we'd like to skip that step if possible. WinXP-embedded is designed to do this automatically, so I know it's possible. I've looked at the Kernel Switches but I didn't see anything documented for "Skip Windows Error Recovery". I've also read extensively on the startup process: http://homepage.ntlworld.com./jonathan.deboynepollard/FGA/windows-nt-6-boot-process.html I know I can disable the auto chkdsk in the registry, but that's not the same thing either. So, how do I streamline the boot process to not hassle the user about a situation that will be the regular normal situation?

  Read the article

• My SSD stopped working as it ends up in blue death right after windows 7 launches, how can I reset it for new windows install?

  - by HattoriHanzo

  As I mentioned in the title my SSD suddenly started to fail as after launching Windows 7 it goes straight to completely idle and after a few minutes it goes to blue death and restarts. I have an another HD with a windows xp on it and it works fine and I can also see the SSD and can access everything on it. Windows 7 on the SSD does work in safe mode though yet I didn't manage to find out what causes the problem. Since I can sill access the files and save them to another HD I'm looking for the best way to wipe and reinstall Windows 7. I have yet failed to find an easy to follow (or even understand) guide, different sources on the internet recommend different ways of doing this. And some guides are just simply full of terms I have no clue about. It's an OCZ Vertex 2 120GB. I"d very much appreciate if someone could give me an advice on what I should do, preferably in a way so I could regain the best possible performance as well. it doesn't matter if I don't understand the science behind it as long as I can follow the steps. Thanks!

  Read the article

• Memory overcommitment on VmWare ESXi 5.0

  - by Tibor

  I would like to understand better the possibilities of VmWare ESXi memory overcommitment. I've read this paper from VmWare, so I am familiar with general concepts, such as hypervisor swapping, memory balooning and page sharing. It seems that a combination of these techniques allows for quite a large degree of overcommitment. However, I am not sure. I am deploying a virtual test lab comprising of 4 identical sets of virtual servers and workstations and a couple of virtual router instances. Overall, I expect to be running around 20 virtual machines with Windows XP, Windows 7 and Ubuntu for workstation hosts as well as CentOS and Windows 2008 Server instances for servers. The problem is, however, that the host machine only has 12GB of RAM and I don't have an option to stuff in some more. I would like to know what is the best option to configure hosts in order to achieve reasonable performance within the constrains. I have these two options: Allocate as little as possible of RAM to each virtual machine. Allocate an extraordinary amount (such as 4 GB per instance) and let the baloon driver do the rest. Something else? Which would work better? Machines will mostly be idle, so I don't have any major performance expectations, but they should run reasonably smoothly nevertheless.

  Read the article

• Xubuntu stuck after login

  - by viraptor

  How can I debug an issue with Xubuntu 12.04 (fresh install) which just waits idle after a login for about 30 seconds? The login screen is delayed correctly. After login, I get my desktop background, but no panels or auto-starting apps. It doesn't seem to be an authentication/pam issue, because I can login without delay at the console while the graphical session is still stuck. There's no disk or cpu activity and no obvious respawning of any process when I look at htop. There's nothing obviously wrong in .xsession-errors. Most interesting errors: openConnection: connect: No such file or directory cannot connect to brltty at :0 WARNING: gnome-keyring:: couldn't connect to: /tmp/keyring-wFn4VR/pkcs11: No such file or directory ... (polkit-gnome-authentication-agent-1:2131): polkit-gnome-1-WARNING **: Failed to register client: GDBus.Error:org.freedesktop.DBus.Error.ServiceUnknown: The nam e org.gnome.SessionManager was not provided by any .service files ** Message: applet now removed from the notification area ** Message: using fallback from indicator to GtkStatusIcon ... (xfce4-indicator-plugin:2176): libindicator-WARNING **: IndicatorObject class does not have an accessible description. ... (xfce4-indicator-plugin:2176): Indicator-Application-WARNING **: Unable to get application list: Operation was cancelled Bootchart seems to end before I login, so it's not that helpful. Where else can I look for information?

  Read the article

• Rtsp Live Stream Android

  - by Filiz Gökçe

  I try to make live stream on android, I try lots of ways, but none of them doesnt work. Could you help me ? This is example of rtsp; mMediaPlayer = new MediaPlayer(); mMediaPlayer.setDataSource(KralStream.getTvStreamUrl().toString()); mMediaPlayer.setDisplay(holder); mMediaPlayer.prepareAsync(); mMediaPlayer.setOnBufferingUpdateListener(this); mMediaPlayer.setOnCompletionListener(this); mMediaPlayer.setOnPreparedListener(this); mMediaPlayer.setOnVideoSizeChangedListener(this); mMediaPlayer.setAudioStreamType(AudioManager.STREAM_MUSIC); mMediaPlayer.setLooping(true); Exeption :05-26 10:22:46.186: ERROR/MediaPlayerService(10157): create PVPlayer 05-26 10:23:06.382: ERROR/PlayerDriver(10157): Command PLAYER_INIT completed with an error or info -1 05-26 10:23:06.382: ERROR/MediaPlayer(23800): error (1, -1) 05-26 10:23:06.382: ERROR/MediaPlayer(23800): Error (1,-1) rtsp; VideoView videoView=(VideoView)findViewById(R.id.videoView1); Uri uri = Uri.parse("rtsp://strm-3.tr.medianova.tv/rkraltv/rkraltv"); videoView.setVideoURI(uri); videoView.start(); Gives message;"Sorry, this video connot ve played." Exeptions;05-26 10:40:08.979: ERROR/MediaPlayerService(10157): create PVPlayer 05-26 10:40:09.188: INFO/ActivityManager(10163): Displayed activity com.giantrabbit.nagare/.KralTvNow: 433 ms (total 433 ms) 05-26 10:40:11.702: WARN/PowerManagerService(10163): Timer 0x3-0x3|0x1 05-26 10:40:29.061: WARN/MediaPlayer(24284): info/warning (1, 26) 05-26 10:40:29.061: INFO/MediaPlayer(24284): Info (1,26) 05-26 10:40:29.100: ERROR/PlayerDriver(10157): Command PLAYER_INIT completed with an error or info -1 05-26 10:40:29.104: ERROR/MediaPlayer(24284): error (1, -1) 05-26 10:40:29.108: ERROR/MediaPlayer(24284): Error (1,-1) rtsp; mPreview = (SurfaceView) findViewById(R.id.surface); holder = mPreview.getHolder(); holder.addCallback(this); holder.setType(SurfaceHolder.SURFACE_TYPE_PUSH_BUFFERS); extras = getIntent().getExtras(); public void play() { try { Uri video = KralStream.getTvStreamUrl(); Toast.makeText(this, video.toString(), Toast.LENGTH_SHORT).show(); mMediaPlayer = new MediaPlayer(); mMediaPlayer.setDataSource(path); mMediaPlayer.setDisplay(holder); mMediaPlayer.prepare(); mMediaPlayer.setOnBufferingUpdateListener(this); mMediaPlayer.setOnCompletionListener(this); mMediaPlayer.setOnPreparedListener(this); mMediaPlayer.setOnVideoSizeChangedListener(this); mMediaPlayer.setAudioStreamType(AudioManager.STREAM_MUSIC); } catch (Exception e) { Log.e(TAG, "error: " + e.getMessage(), e); } } Exeption ; 05-26 10:36:57.589: ERROR/MediaPlayerService(10157): create PVPlayer 05-26 10:37:20.542: ERROR/PlayerDriver(10157): Command PLAYER_INIT completed with an error or info -1 05-26 10:37:20.542: ERROR/MediaPlayer(24240): error (1, -1) 05-26 10:37:20.565: WARN/PlayerDriver(10157): PVMFInfoErrorHandlingComplete 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): error: Prepare failed.: status=0x1 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): java.io.IOException: Prepare failed.: status=0x1 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.media.MediaPlayer.prepare(Native Method) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at com.giantrabbit.nagare.KralTvNow.play(KralTvNow.java:162) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at com.giantrabbit.nagare.KralTvNow.surfaceCreated(KralTvNow.java:215) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.SurfaceView.updateWindow(SurfaceView.java:536) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.SurfaceView.dispatchDraw(SurfaceView.java:339) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.ViewGroup.drawChild(ViewGroup.java:1638) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.ViewGroup.dispatchDraw(ViewGroup.java:1367) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.ViewGroup.drawChild(ViewGroup.java:1638) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.ViewGroup.dispatchDraw(ViewGroup.java:1367) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.View.draw(View.java:6796) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.widget.FrameLayout.draw(FrameLayout.java:352) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.ViewGroup.drawChild(ViewGroup.java:1640) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.ViewGroup.dispatchDraw(ViewGroup.java:1367) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.View.draw(View.java:6796) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.widget.FrameLayout.draw(FrameLayout.java:352) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at com.android.internal.policy.impl.PhoneWindow$DecorView.draw(PhoneWindow.java:1894) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.ViewRoot.draw(ViewRoot.java:1407) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.ViewRoot.performTraversals(ViewRoot.java:1163) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.view.ViewRoot.handleMessage(ViewRoot.java:1727) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.os.Handler.dispatchMessage(Handler.java:99) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.os.Looper.loop(Looper.java:123) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at android.app.ActivityThread.main(ActivityThread.java:4627) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at java.lang.reflect.Method.invokeNative(Native Method) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at java.lang.reflect.Method.invoke(Method.java:521) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at com.android.internal.os.ZygoteInit$MethodAndArgsCaller.run(ZygoteInit.java:871) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at com.android.internal.os.ZygoteInit.main(ZygoteInit.java:629) 05-26 10:37:20.682: ERROR/MediaPlayerDemo(24240): at dalvik.system.NativeStart.main(Native Method) 05-26 10:37:20.737: INFO/MediaPlayer(24240): Info (1,26) 05-26 10:37:20.737: ERROR/MediaPlayer(24240): Error (1,-1) 05-26 10:37:20.868: INFO/ActivityManager(10163): Displayed activity com.giantrabbit.nagare/.KralTvNow: 25864 ms (total 25864 ms) 05-26 10:37:23.777: WARN/PowerManagerService(10163): Timer 0x3-0x3|0x1 This is example of http ; mMediaPlayer = new MediaPlayer(); mMediaPlayer.setDataSource("http://ikral.garantisistem.com:1935/ikral/smil:kral.smil/playlist.m3u8"); mMediaPlayer.setDisplay(holder); mMediaPlayer.prepareAsync(); mMediaPlayer.setOnBufferingUpdateListener(this); mMediaPlayer.setOnCompletionListener(this); mMediaPlayer.setOnPreparedListener(this); mMediaPlayer.setOnVideoSizeChangedListener(this); mMediaPlayer.setAudioStreamType(AudioManager.STREAM_MUSIC); mMediaPlayer.setLooping(true); Exeption: 05-26 10:16:24.276: ERROR/MediaPlayerService(10157): create PVPlayer 05-26 10:16:24.292: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferWriteDataStreamImpl 05-26 10:16:24.346: INFO/PlayerDriver(10157): buffering (100) 05-26 10:16:24.346: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferReadDataStreamImpl 05-26 10:16:24.346: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferReadDataStreamImpl 05-26 10:16:24.346: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferReadDataStreamImpl 05-26 10:16:24.346: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferReadDataStreamImpl 05-26 10:16:24.346: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferReadDataStreamImpl 05-26 10:16:24.346: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferReadDataStreamImpl 05-26 10:16:24.346: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferReadDataStreamImpl 05-26 10:16:24.346: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferReadDataStreamImpl 05-26 10:16:24.346: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferReadDataStreamImpl 05-26 10:16:24.346: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferReadDataStreamImpl 05-26 10:16:24.346: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferReadDataStreamImpl 05-26 10:16:24.346: ERROR/(10157): IIIIIII Inside Constructor of PVMFMemoryBufferReadDataStreamImpl 05-26 10:16:24.350: WARN/MediaPlayer(23736): info/warning (1, 26) 05-26 10:16:24.354: ERROR/PlayerDriver(10157): Command PLAYER_INIT completed with an error or info -10 05-26 10:16:24.354: ERROR/MediaPlayer(23736): error (-10, -10) 05-26 10:16:24.354: WARN/PlayerDriver(10157): PVMFInfoErrorHandlingComplete 05-26 10:16:24.393: INFO/MediaPlayer(23736): Info (1,26) 05-26 10:16:24.393: ERROR/MediaPlayer(23736): Error (-10,-10) Htttp; VideoView videoView=(VideoView)findViewById(R.id.videoView1); Uri uri = Uri.parse("http://ikral.garantisistem.com:1935/ikral/smil:kral.smil/playlist.m3u8"); videoView.setVideoURI(uri); videoView.start(); Gives message;"Sorry, this video connot ve played." Filiz Gökçe

  Read the article

• Windows 8 Install Hanging at first white-font boot splash

  - by Omega

  I'm trying to install the Windows 8 preview on my Samsung Series 9 (2012, Ivy Bridge). I've done a bit of a custom scheme with this one: I'm using EFI/UEFI on this system. I've seen no indication that this system supports secure boot (yay!) My SSD is set up with GPT Ubuntu is already installed and working great via UEFI. I'm trying to boot the Windows 8 install from a USB stick via UEFI I don't have access to a CD drive. The problem is that the boot seems to hang at the very first splash screen that looks like this. White windows font, the little beads don't show up. My USB stick has an activity light and it does blink for the first few seconds, but then goes back to it's "nobody is talking to me" idle pulse. What I know: UEFI booting is definitely working. Windows 8 for those few seconds seems to have some kind of access to the USB drive. My Series 9 is running the latest BIOS/firmware. Any idea what I might be able to do to get Windows 8 installed??

  Read the article

• ASP.Net Session Timing Out Rapidly

  - by Zac

  We have an ASP.Net 3.5 website running on Windows Server 2008 with IIS7. The session timeout period for this site is configured to be 20 minutes - however, it is currently lasting for between 40 and 50 seconds. After researching the problem we investigated several configuration values which could be involved in the timeout period but none of them are set to less than 20 minutes. The areas we look are as follows: web.config system.web/sessionState element (20 minutes). web.config system.web/authentication/forms element (not present, defaults to 30 minutes). Sites/{website}/ASP/Session Properties/Time-out (20 minutes). Application Pools/{appPool}/Advanced Settings/Process Model/Idle Time-out (20 minutes). We've also noted that the CPU is staying around 0% and that RAM usage is flat-lining around 1.07 GB (of 8 GB available) - so there is no performance-based reason for IIS to be recycling the Application Pool as far as we can tell. Are there any settings we've overlooked which could cause the session timeouts to be expiring so quickly? EDIT A couple of additional points: This is not occurring in development, only on the server. The session is not sliding (i.e. if we refresh the page a few times it still times out approximately 40 - 50 seconds after the session was created.

  Read the article

• OpenVPN server will not redirect traffic

  - by skerit

  I set up an OpenVPN server on my VPS, using this guide: http://vpsnoc.com/blog/how-to-install-openvpn-on-a-debianubuntu-vps-instantly/ And I can connect to it without problems. Connect, that is, because no traffic is being redirected. When I try to load a webpage when connected to the vpn I just get an error. This is the config file it generated: dev tun server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt ca ca.crt cert server.crt key server.key dh dh1024.pem push "route 10.8.0.0 255.255.255.0" push "redirect-gateway" comp-lzo keepalive 10 60 ping-timer-rem persist-tun persist-key group daemon daemon This is my iptables.conf # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *raw :PREROUTING ACCEPT [37938267:10998335127] :OUTPUT ACCEPT [35616847:14165347907] COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *nat :PREROUTING ACCEPT [794948:91051460] :POSTROUTING ACCEPT [1603974:108147033] :OUTPUT ACCEPT [1603974:108147033] -A POSTROUTING -s 10.8.0.0/24 -o eth0 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o eth1 -j MASQUERADE -A POSTROUTING -s 10.8.0.0/24 -o venet0 -j MASQUERADE COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *mangle :PREROUTING ACCEPT [37938267:10998335127] :INPUT ACCEPT [37677226:10960834925] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [35616847:14165347907] :POSTROUTING ACCEPT [35680187:14169930490] COMMIT # Completed on Sat May 7 13:09:44 2011 # Generated by iptables-save v1.4.4 on Sat May 7 13:09:44 2011 *filter :INPUT ACCEPT [37677226:10960834925] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [35616848:14165347947] -A INPUT -i eth0 -j LOG --log-prefix "BANDWIDTH_IN:" --log-level 7 -A FORWARD -o eth0 -j LOG --log-prefix "BANDWIDTH_OUT:" --log-level 7 -A FORWARD -i eth0 -j LOG --log-prefix "BANDWIDTH_IN:" --log-level 7 -A OUTPUT -o eth0 -j LOG --log-prefix "BANDWIDTH_OUT:" --log-level 7 COMMIT # Completed on Sat May 7 13:09:44 2011

  Read the article

• What is the best hosting option for Flash web-widget?

  - by par

  Our Flash web-widget has got highly popular. It is downloaded around 100,000 times per day. And that is the problem. Our server bandwidth is too narrow to deliver the widget to the clients fast. The widget is loaded very slow. Probably 20 times slower than before (at peak times). Probably I have choosen not the right hoster for my task - delivering 1 MB Flash widget to 100,000 users per day. What is the best hosting solution in my case? I'm not good at server administration so forgive me if I sound naive. The details are the following. Our hoster options: -Dedicated server, Ubuntu -10 Mbit Connection -monthly bandwidth limit: 2000 GB Widget size is 1 MB. The widget consists of the main SWF and a number of loaded SWF and data files. This is a part of Apache Status report taken right now ---- Server uptime: 1 hour 2 minutes 38 seconds Total accesses: 74865 - Total Traffic: 5.8 GB CPU Usage: u28 s7.78 cu0 cs0 - .952% CPU load 19.9 requests/sec - 1.6 MB/second - 81.1 kB/request 200 requests currently being processed, 0 idle workers WWWWWWWWWWWWWWWWWWWWWWWWCWWWWWWWWWWWWWWWWWWWWWWWWWWCWWWWWWWCWWWW WWWWWCWWWWWWWWWWWWWWCWWWWWWWWWWWWCWWWWWWWWCWWCWWWWWWWWWWWWWWWWWW WWWWWWWWWWWWWWWWCWWWWWWWWWWWWWWWWWWWWWWWWWWWCWCWWWWWWWWWWWWWWWCW WWWWWWWW........................................................ ----

  Read the article

• MySQL stops accepting connections over 3306, still working on localhost

  - by Ben Dilts

  I have a MySQL database that stopped accepting connections from my web server altogether. So I SSH'ed into the server and started checking its vitals. The hard disks had plenty of open space, and there was plenty of available memory and swap space. Nothing was eating up the CPU (close to 100% idle). I even connected to MySQL locally and ran a few queries without any issues. But SHOW PROCESSLIST only showed my own connection, no others. Worst of all, in the MySQL log, no errors even remotely coincided with the unavailability of the server. On the web server, I got an error saying "Lost connection to MySQL server during query" at the moment the unavailability started, followed by a bunch of "MySQL server has gone away" errors. There's only one other application on the server that accepts network connections, and I killed that one (in case it was holding too many open connections or something), but it didn't help. Finally I just restarted the MySQL process, and everything is (for now) working again. What else should I check in these circumstances? Any idea what the problem might be? And how might I verify that is in fact the problem?

  Read the article

• Windows 7 breaks even in safe mode

  - by delenda

  Hi, I have a Dell XPS M1730 with Windows 7 installed. I noticed last night that after a few hours of use, the fans kicked into full and I couldn't do anything without it taking forever. Minimising windows, opening device manager or even opening process explorer took minutes and a game install I had just started took nearly 4 hours to complete. When procexp finally loaded, the refresh was so slow that it was mostly useless. From what I could gather, it was reporting 60% idle processes with procexp using nearly 40%. There were no hardware interrupts listed. When I rebooted, the problem went away for about 10 minutes and then the same thing happened. The issue persists in safe mode and even after I removed the graphics drivers, which have been an issue in the past, it still happens. Icons flash quite quickly on the desktop periodically and screen refresh is painfully slow. When booting now, the fans kick in to full as soon as the windows logon box comes up and it's taking 10 minutes to bring the desktop up. Chkdsk reports nothing and the raid check says that everything is fine. I'm thinking hardware failure, probably HDD but wanted some other opinions. I'm planning to try a linux live cd to see if it works without using the hard disks. If anyone has any input, it would be greatly appreciated. Delenda

  Read the article

• What hardware would I need (approx) to run ESXi server?

  - by mr.b

  Hi, I am considering to purchase off-the-shelf commodity hardware in order to build server that will host virtual machines using ESXi server. Intended purpose for this server is NOT mission critical tasks. It will have to run perhaps 20-50 Windows XP/Vista/7 virtual machines (in total, but closer to 20 figure). Each guest would have to have 1-2 GB of ram, and probably two-three times more disk space than guest OS needs with clean install and all updates applied (that would be around 6-8 GB for XP, and i believe closer to 10-15 for win7). Those guests will act as a test ground for a new product that is network management software, thus guests will idle most of their time once initially loaded, but if I give them some task to complete, they should be able to perform reasonably well. Now, from what I have learned... CPU is usually not much of an issue (6 cores would do it), memory should not be lacking, but doesn't have to be sum of all guests, because of overcommitment... That leads me to IO, which is, as it seems, the bottleneck. Since I have very little experience with ESXi (and ESX, too) server, I'd like to ask: How much memory could I save by overcommitment, and how does it affect performance? Is 6-core cpu enough to run above described system? Would it be possible to run entire server off two (or even one) SSD drives (to host system virtual disks, with few additional HDDs (2-3) in RAID 0 to be used as secondary storage? I read somewhere that ESXi allows having something like "master image", essentially virtual machine that is "deployed" many times, so that disk space can be saved by having only differences stored by specific guests, instead of copying around whole virtual disks. Is this true, and how can this help me? Are there any other things I need to take into consideration when building this off-the-shelf solution? I should probably mention here that I'm fully aware of issues like SPOF regarding power supply, raid 0, etc, but since it's only a testing ground and not a production system, it's not so important for me. Thanks, B.

  Read the article

• Packet flooding while configuring a Debian L2TP/IPSec client?

  - by Joseph B.

  I'm currently at my wits end trying to configure an L2TP over IPSec VPN connection on my Debian using openswan and xl2tp box connecting to a server of unknown configuration. I've managed to successfully establish the connection and everything appears to be working well until I attempt to set the VPN connection as my default route, at which point I see a massive flood of packets simultaneously being transmitted (on the tune of ~1.5 GB in about 2min) until the server drops my connection. Prior to this network traffic on all my interfaces is minimal. According to iftop the majority of this traffic appears to be coming out of port 12, although I can't seem to figure out how to finger a specific process. If I instead just route traffic destined for 74.0.0.0/8 through it I'm able to access Google's servers through the VPN without issue. My xl2tp.conf file is: [lac vpn-nl] lns = example.vpn.com name = myusername pppoptfile = /etc/ppp/options.l2tpd.client My options.l2tpd.client file is: ipcp-accept-local ipcp-accept-remote refuse-eap require-mschap-v2 noccp noauth idle 1800 mtu 1410 mru 1410 usepeerdns lock name myusername password mypassword connect-delay 5000 And my routing table looks like: Destination Gateway Genmask Flags Metric Ref Use Iface 10.5.2.1 * 255.255.255.255 UH 0 0 0 ppp0 10.0.50.0 * 255.255.255.0 U 0 0 0 eth0 10.50.0.0 * 255.255.0.0 U 0 0 0 eth0 10.0.0.0 * 255.255.0.0 U 0 0 0 eth0 192.168.0.0 * 255.255.0.0 U 0 0 0 eth0 loopback * 255.0.0.0 U 0 0 0 lo default * 0.0.0.0 U 0 0 0 ppp0 I'm seeing absolutely nothing in auth.log and syslog during this time and can't seem to find any other log files it might be writing to. Any suggestions would be appreciated!

  Read the article

• Apache using 100% CPU, once again

  - by CBenni

  Recently, apache2 started using 100% of CPU power: top gives me From other, similar threads, I took the tip to use mod_status. Aside from HUGE amounts of NULL requests, it gives: CPU Usage: u2.16 s1.32 cu0 cs0 - .0835% CPU load 1.2 requests/sec - 17.6 kB/second - 14.6 kB/request 8 requests currently being processed, 42 idle workers The access and error logs do not show anything surprising or intriguing at all. Note the .8% CPU usage. Another tip was to use strace: root@server:~# strace -p 1956 Process 1956 attached - interrupt to quit restart_syscall(<... resuming interrupted call ...> And remains like this for at least half an hour, without producing any additional output. Restarting apache fixed the problem for less than a second The server runs a few custom python scripts aswell as a django-powered website on apache2 (up-to-date), but even turning the scripts off (or not having them active in the first place) did not change anything. After I stopped apache and powered my server off, powered it on a few minutes afterwards and restarted all my services, the CPU usage remained low for several hours, just in order to pop up again randomly (?) The DigitalOcean CPU stats on my server are: You can see how the CPU usage was super high for almost half a day until I restarted the bot - just to remain stable for several hours and then pop up again. I am completely at a loss of words and don't know what I could do to find out what piece of my code is giving me these problems or if apache itself is the cause... Therefore I would greatly appreciate any hints to the questions: What else can I try to do? Which things might I not have checked? Is this definitely in my own code? How do you find what part of python code crashes an app via a infinite loop or similar?

  Read the article

• Optimizing Apache for large file serving

  - by D_Guy13

  I have a random problem with Apache that I can't quite figure out, here is my setup, Windows Server 2008 R2, 64 Bit, 5GB RAM, SSD with 200 MB(Read/write) and Dual Core CPU @ 2.1 GHz A dump from mod-staus, Server Version: Apache/2.4.7 (Win32) mod_limitipconn/0.24 mod_antiloris/0.5.2 PHP/5.5.9 Server MPM: WinNT Apache Lounge VC11 Server Built: Nov 21 2013 20:13:01 Current Time: Thursday, 21-Aug-2014 23:38:06 W. Europe Daylight Time Restart Time: Thursday, 21-Aug-2014 20:30:47 W. Europe Daylight Time Parent Server Config. Generation: 1 Parent Server MPM Generation: 1 Server uptime: 3 hours 7 minutes 18 seconds Server load: -1.00 -1.00 -1.00 Total accesses: 283025 - Total Traffic: 1172.2 GB 25.2 requests/sec - 106.8 MB/second - 4.2 MB/request 62 requests currently being processed, 388 idle workers Serving large .zip & iso files using mod_xsendfile. (File size range 500 MB - 1.5 GB) The setup works and is running fine. CPU usage is very unstable, jumps all the time between 10% - 90% and the servers goes down when it hits 100%. In that case I have to hard restart the server. Server it outputting traffic at 30 Mbps. Is there anything else I should think about to get a more stable CPU usage? Is that CPU usage normal? Can switching to Linux help me achieve better CPU usage?

  Read the article

• Computer loop restarts on Windows loading

  - by Robinson G.

  My computer restarts, just after or during Windows loading (4 squares getting together), or after some time on the desktop IF I'm idle. In order to start the computer I either have to swap my RAM (24Go) in differents DIMM slots, for example (I have 4 slots) : 1-2-4 or 2-3-4 or 1-3-4, not the same position each boot or it restarts in a loop... I can also change the ram timing from 1.5 to 1.6V and it starts, at the next reboot I have to change it again to 1.5 or it won't boot... And If after all, I succeed to boot, I have to use the computer for about 10 minutes, and it's ok, if I don't, it restarts by itself after some minutes. If I stay on the BIOS, It's all OK, I can stay for a whole year without restarting. I have check my RAM on Memtest (4*8G SDRAM DDR3) : OK I have check without graphic card : Still the same. I tried to reset the bios stack by getting it off and on : Still the same. I tried to reset my BIOS, and many settings about the RAM in the menu : Still the same. CPU temps are just fine (around 35°C) I was thinking ofc about the motherboard but I want to be sure. Motherboard : MSI zh77a-g43 RAM : 4*8G Dual Mode or not (depends on the number I put ofc.) PSU : 600W (enough to run all the config) CPU : i7 3770 non K

  Read the article

• saving data from a failing drive

  - by intuited

  An external 3½" HDD seems to be in danger of failing — it's making ticking sounds when idle. I've acquired a replacement drive, and want to know the best strategy to get the data off of the dubious drive with the best chance of saving as much as possible. There are some directories that are more important than others. However, I'm guessing that picking and choosing directories is going to reduce my chances of saving the whole thing. I would also have to mount it, dump a file listing, and then unmount it in order to be able to effectively prioritize directories. Adding in the fact that it's time-consuming to do this, I'm leaning away from this approach. I've considered just using dd, but I'm not sure how it would handle read errors or other problems that might prevent only certain parts of the data from being rescued, or which could be overcome with some retries, but not so many that they endanger other parts of the drive from being saved. I guess ideally it would do a single pass to get as much as possible and then go back to retry anything that was missed due to errors. Is it possible that copying more slowly — e.g. pausing every x MB/GB — would be better than just running the operation full tilt, for example to avoid any overheating issues? For the "where is your backup" crowd: this actually is my backup drive, but it also contains some non-critical and bulky stuff, like music, that aren't backups, i.e. aren't backed up. The drive has not exhibited any clear signs of failure other than this somewhat ominous sound. I did have to fsck a few errors recently — orphaned inodes, incorrect free blocks/inodes counts, inode bitmap differences, zero dtime on deleted inodes; about 20 errors in all. The filesystem of the partition is ext3.

  Read the article

• How to resume XMPP groupchat window in Irssi (using bitlbee)?

  - by mcnesium

  I use Bitlbee to chat in XMPP-networks within my IRC-client Irssi. This works great so far, and recently I started using XMPP Multi User Chats as an alternative to IRC-channels. I set up a channel using chat add <account> <[email protected]> in the &bitlbee control window, set chan <room> set autojoin true and entered /join #room in the &bitlbee window to join that groupchat. It then appears as a unique Irssi window in the status bar. This seems to work ok too, but with one exception: Since I idle in the channels 24/7 my irssi has to cope with the every-night-24h-DSL-disconnection by the ISP. After it automatically reconnects, it does kind of rejoin that XMPP-groupchat, but the traffic of the groupchat does not go back to the unique irssi window, but keeps flooding &bitlbee with messages from root telling me about a Groupchat Message from unknown JID <jid>: <message> - which is the traffic of the groupchat. The unique groupchat window is gone after the reconnect, and I will again have to go /join #room in &bitlbee to get it back. Even worse, the window number is unused before I rejoin the groupchat, and if I get a query from any network, the window nests in that unused window spot, so I will first have to remove that query from the spot, and then move the rejoined groupchat to that window number. I want my groupchat window to resume after the reconnect just like every other IRC channel too. How can I get this done? Any ideas?

  Read the article

• Stop Windows 7 from accessing or writing to hard drive unless "told" to by me? (More info inside...)

  - by Jeff

  A confusing question, perhaps, but bear with me. I have two internal HDDs set up in a RAID0 array which I use as mass storage. I access the drive very infrequently (once a day at most) and so I have set up Windows 7's power options to turn off idle disks after only 1 minute. This is fine, and the disks are turned off most of the time. However, I notice that Windows sometimes spins up the drives when I really, really don't want or need it to. This causes a 30 second delay as both drives spin up and lock up my system. Some examples of when this happens: 1) When I'm installing something using Windows Installer or Installshield; it seems to me as if they're using the drive with most available free space as the installer cache location... so my big RAID drive has to spin up! Most annoying. 2) Apparently, when I open a Java-based program which resides on my system drive and has nothing to do with my RAID drive! 3) At boot-up and shut-down time. At shutdown the drive spin up only for the computer to immediately shut down! Incredibly frustrating! I've already tried changing the letter of the drive, and at some points have removed the drive letter entirely, which solves the first two issues above. So my question (FINALLY!) is this: is there any way I can mark this drive as being for "storage only", so Windows basically does not see it at all until I actually invoke it somehow? Or is there any way I could set it up so that only specific programs have write access to it? For example, download managers, TeraCopy, etc. etc.? Basically I want it to be a "ghost drive" until I'm ready to use it and to stop Windows from spinning it up all the damn time! Thank you. :)

  Read the article

• What is best configuration settings for Wordpress and MySQL on Win2008 + IIS7 stack?

  - by holiveira

  I currently have four blogs that uses Wordpress running on a shared hosting company. This blogs have a considerable amount of visits and I'm constantly receiving warnings from the hosting company saying that I'm consuming too much server CPU. Considering the fact that I have a dedicated server in another company with plenty of idle resources (it has a quad core Xeon 2.5GHz and 8GB of Ram and run on Win2008) I'm planning to move the blogs to this server in order to have some more freedom. I'm currently using this server to host some web applications using ASP.Net and SQL Express. I've installed a blog to test and it worked fine, but some issues appeared and raised some questions in my mind: How to properly set the permissions in the folders used by wordpress plugins, I mean, what permissions should I set for the IIS_User in some folders so that the plugins works correctly? What's the best caching plugin to use considering this is a Window Server? In the previous hosting company I used the WPSuperCache, but it was a Linux Stack. Or should I ignore the caching plugins and use the Dynamic Caching Feature of IIS7? How can I optmize the MySQL server running in this server (specially the settings regarding memory and caching) How can I protect the admin folders against hacker attacks? I know some people will advice me not to run Wordpress in a Windows stack, but that's my only choice. I don't even know were to start managing and LAMP stack, don't have the time to do so nor the money to rent another server.

  Read the article

< Previous Page | 80 81 82 83 84 85 86 87 88 89 90 91  | Next Page >