Search Results

Search found 4376 results on 176 pages for 'drivers'.

Page 85/176 | < Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >

  • How can I start hostednetwork on Windows 7?

    - by Pirozek
    When I type in admin console command to start hostednetwork netsh wlan start hostednetwork it gives me this: The hosted network couldn't be started. The group or resource is not in the correct state to perform the requested operation. There is a hotfix from Microsoft but it didn't help me. Any advice? C:\Users\Pirozek>netsh wlan show driver Interface name: Wireless Network Connection 3 Driver : D-Link AirPlus DWL-G520 Wireless PCI Adapter(rev .B) Vendor : Atheros Communications Inc. Provider : Atheros Communications Inc. Date : 8.7.2009 Version : 8.0.0.171 INF file : C:\Windows\INF\oem108.inf Files : 2 total C:\Windows\system32\DRIVERS\athrx.sys C:\Windows\system32\drivers\vwifibus.sys Type : Native Wi-Fi Driver Radio types supported : 802.11b 802.11g FIPS 140-2 mode supported : Yes Hosted network supported : Yes Authentication and cipher supported in infrastructure mode: Open None Open WEP-40bit Shared WEP-40bit Open WEP-104bit Shared WEP-104bit Open WEP Shared WEP WPA-Enterprise TKIP WPA-Personal TKIP WPA2-Enterprise TKIP WPA2-Personal TKIP Vendor defined TKIP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA-Enterprise CCMP WPA-Personal CCMP WPA2-Enterprise CCMP Vendor defined CCMP WPA2-Enterprise Vendor defined Vendor defined Vendor defined WPA2-Personal CCMP Authentication and cipher supported in ad-hoc mode: Open None Open WEP-40bit Open WEP-104bit Open WEP WPA2-Personal CCMP

    Read the article

  • Multiple copies off the same printer on Windows 7 from PrintUIEntry

    - by Kev
    I currently have a number of bat files which work perfectly fine on Windows XP which install the same printer multiple times with a number of finisher options set - e.g. after running the bat file below I would end up with four printers in the printer drop down called Sharp Kits Printer - A4 Single Sided Sharp Kits Printer - A4 Single Sided Stapled Sharp Kits Printer - A4 Duplex Stapled Sharp Kits Printer - A4 Duplex which all have there options configured in the relevant way. I have amended on Windows 7 to point to correct INF file and printer name in the INF files - a single printer installs fine. However when I run the complete batch file only the first printer in it is installed - occassionally the later ones flash up in the GUI but then vanish when you press F5 and are still missing after a reboot. SET QUEUENAME=http://192.168.7.123:631/printers/Sharp700 SET PPD=J:\DRIVERS\Printers\MX700-Win7-64\SJ1JWENG.INF SET PPDENTRYNAME=SHARP MX-M700U PPD J: cd "\DRIVERS\Printers\MX700-Win7-64" SET NICENAME="Sharp Kits Printer - A4 Single Sided" SET PREFS="J:\SCRIPTS\Printers-Win7-64bit\Sharp_SINGLE_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... SET NICENAME="Sharp Kits Printer - A4 Duplex" SET PREFS="J:\SCRIPTS\Printers\Sharp_DUPLEX_SETTINGS.dat" %SYSTEMDRIVE%\WINDOWS\system32\rundll32.exe %SYSTEMDRIVE%\WINDOWS\system32\printui.dll,PrintUIEntry /w /b %NICENAME% /x /n "part of the n switch" /f "%PPD%" /if /r "%QUEUENAME%" /m "%PPDENTRYNAME%" rem restore settings go here... I have tried adding the "/u" paramater to the end, I have changed the "/n" paramater to be different (e.g. n1, n2,n3 etc) - both of these result in the same. I have also tried to change the port (/r) to have "_1" (etc) on the end like the GUI would but this errors as the port doesn't exist. Is it possible to do this on Windows 7, and if so how?

    Read the article

  • Can I use HP Recovery Discs for a different hard drive capacity and make?

    - by Fasih Khatib
    About two years ago I created HP Recovery Discs (3 of them). Now my hard drive has crashed and new one is still a week from delivery. I was reading up on how to reinstall the genuine OS using the Recovery Discs as i was not given any Windows 7 installation discs. I did my bit of research after getting answers from the community on what these discs do and found out on other sites that people experience issues when recovering their OS from the disc. Especially when they change the make or capacity of the harddrive. Unfortunately I had to change the make as the hard drive that came built in has gone out of production. This question is just a part of my checklist to avoid problems when recovering the OS. I have: HP DV4-2126TX (available only in India I guess) I had: Seagate Momentus 320 GB I ordered: Western Digital Scorpio Black 500 GB Windows 7 Home Premium 32-bit Is there a possibility to encounter any problems due to the changed capacity and make? I only want my genuine OS and drivers – not my data. I was told that Disc 1 contained the OS and drivers, and the rest of the discs contained data. I couldn't verify that.

    Read the article

  • Windows 7 'Unidentified Network'

    - by Throdne
    So my internet was working last night before I went to bed and woke up to a computer that is showing unidentified network. I have tried multiple ways of fixing it. > route delete 0.0.0.0 > uninstalling drivers - restart - reinstall from downloaded drivers > ipconfig /release - /renew > static IP > speed & duplex from auto negotiation to 1.0gbps full duplex > and also changed my network address to no value to 1234567890ab (not in that order) nothing seems to work. I have Comcast internet and when I connect the computer to the modem it works perfectly. but when I connect it to my router again, Unidentified network. I know my router isn't faulty, because my macbook pro, server, NAS, iPhones, and iPads are still working. I have also tried moving the port on the router, still same problem. my router is a: Cisco Small Business RVS4000 motherboard: GIGABYTE GA-990FXA-UD3

    Read the article

  • RAID5 issue after replacing motherboard and upgrading firmware

    - by 8steve8
    ok so ive had a 4x2TB(samsung HD204UI w/firmware patch) raid5 array working normally for about a month. It was in a h57 gigabyte motherboard using the intel raid with Windows 7 x64. Today I got an intel h67 motherboard, so I upgraded the intel raid drivers to 10.1.0.1008 from 9.6.0.1014, and I'm not sure if i checked after a reboot, but it caused no problems. I swapped in the new dh67 motherboard, and my array status was "failed". 2 of the 4 drives listed themselves as members, while the other two drives listed themselves as non-members. I tried going back to the old h57 mobo, and downgrading the raid drivers, but the issue remains. It's not port dependent, 2 of the drives always come up as non-members regardless of what port or motherboard they are plugged into. This screenshot should show that the SNs match, which raises the question why the software doesn't realize the drive is a member of the array. I'd like to know if anyone has experienced anything similar, and what should I do, can I force the drive to be recognized as a member (without wiping data)?

    Read the article

  • Volume is no longer showing in Raid Controller BIOS and in Windows

    - by Gordon
    Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

    Read the article

  • Computer Won't Boot Properly, unless in safe mode?

    - by Mr_CryptoPrime
    I bought a computer today and booted it up, but when I did I only got a blank screen. I checked to make sure it wasn't the monitor by connecting it to my old computer...it worked. I then tried connecting my monitor to both DVI ports and found that the bottom one did work. However, now it just boots up and says "loading windows" and then when the login screen is suppose to come up the screen just goes blank and monitor says "no input, check cord" (or something like that). I tried reinstalling windows and then I was able to log on normally. I used the CD's and reinstalled all the drivers, then rebooted...now I am stuck right back where I started. I tried taking out the RAM and inserting into different slots, that didn't fix anything. I was able to boot up into windows using safe-mode. I suspected that my ATI Radeon 6950 was the issue and downloaded the drivers, but I can't install them on safe-mode. Someone said to install C++ distr. and I tried doing that to fix driver installation problem of "failed to load detection driver" but it wouldn't let me do that either. Please someone help me, I don't want to have to deal with the evil redtape of sending it back to get a replacement! My computer: -Content--text-_-"http://www.newegg.com/Product/Product.aspx?Item=N82E16883229236&nm_mc=TEMC-RMA-Approvel&cm_mmc=TEMC-RMA-Approvel--Content--text-_- Driver detection problem: http://www.hardwareheaven.com/hardwareheaven-tools-discussion/174912-failed-load-detection-driver-installation-error.html Driver download page: http://sites.amd.com/us/game/downloads/Pages/radeon_win7-64.aspx#1 I am using windows 7. Thanks again.

    Read the article

  • How do I automatically connect my client to an ODBC data source on another machine with dynamic IP?

    - by Kdansky
    At the customer's place, we've got a postgres DB on a server, and a few clients. We connect them through ODBC-drivers, and all machines run windows (usually XP). Now we had a few annoying issues: The client "forgets" some flags in the ODBC drivers, such as ByteA as LO. Every time anything changes, we have to reset that, and type in the password, and sometimes even the IP of the server. On x64 machines running Windows 7, configuring this is a pain as the system settings dialogue will only show 64-bit connections by default. And most importantly: If the server changes IP because the customer restarts or replaces a switch, all connections are lost. Annoyingly, this cannot be fixed with just correcting the IP, but rather, we have to check every single place (even hba_conf) because all the settings magically disappear. Our customers often are very small companies, where "server" means "that one PC in the other room", and not "Oracle mainframe in the dungeon", so we don't want to rely on them not restarting switches. Is there a better way than to rely on these really unstable settings? Are these settings somewhere in a file which I could edit manually, to make fixing it easier?

    Read the article

  • Can I have a single solid state drive and a RAID array on the same machine? [closed]

    - by jaminto
    Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

    Read the article

  • Application Screen Repainting Issues

    - by Jeff Sheldon
    I have this issue lately at work. It drives be nuts, and I finally stopped to ask this question. It's quite often that an application I've been running just randomly fails to repaint itself for a while, usually in the editor screen. I most often see this occurring with Expression Web, Visual Studio 2008/2010 and SQL Server Management studio. These applications are what I work in the most, so I'm not surprised to mostly see it here. But I was curious if anyone else had a solution for this. I've tried: Reboots. The screen shot below is about 10 minutes after a reboot. New Video Drivers. This machine is running a Nvidia Quadro NVS 290 video card with the latest drivers. Closing other applications, this is the only thing running right now. As far as hardware, this machine has Dual Quad-Core Xeon 2.83ghz Processors, with 10 gigs of memory, running Windows XP SP3 64bit. Any help would be great. JNK EDIT: Per comments from deleted (wrong) answer: I'm running dual monitors. Set it to single display, still occurred. Rebooted, and tried it again, and it still occurred. Switched it back to dual screen. My resolution is only 1400x900 on each.

    Read the article

  • USB 3.0 ports backwards compatibility problems with 2.0 devices?

    - by AaronLS
    I see some info on the net that suggest that I should be able to get my USB 2.0 devices to work in 3.0 ports. I only have two 2.0 ports on my new computer, and six 3.0 ports. I have installed drives. There's two different drivers, I guess some of the ports are supported by the intel board and some supported by some other chipset on the motherboard. I however have yet to get any of the 3.0 ports to work, and my brother had had the same issue with his devices not working in 3.0 ports on his computer. So I am beginning to wonder if the backwards compatibility isn't reliable for some reason. Maybe manufacturers opting not to implement 2.0 support on the 3.0 ports. I understand that physically the wiring is there, but that is only half the story. Beyond my brother's and my own computers (different motherboards/everything), I have yet to see a 2.0 device work in a 3.0 port. Is there any reason for this apparent device incompatibility? I.e. looking for responses that would indicate what areas to explore for issues or if there is any known cases of manufacturers deviating from spec in hardware or drivers. I am aware it's "supposed" to work :) Update: Does this have any relation to "USB Legacy Support" options in the BIOS? There several options combinations of options with "USB Legacy Support" and "USB 3.0 Legacy Support" and the description for these is a bit confusing, sounds like a bad translation.

    Read the article

  • strange raid5 issue:

    - by 8steve8
    ok so ive had a 4x2TB(samsung HD204UI w/firmware patch) raid5 array working normally for about a month. It was in a h57 gigabyte motherboard using the intel raid with windows 7 x64. Today I got an intel h67 motherboard, so I upgraded the intel raid drivers to 10.1.0.1008 from 9.6.0.1014, and I'm not sure if i checked after a reboot, but it caused no problems. I swapped in the new dh67 motherboard, and my array status was "failed". 2 of the 4 drives listed themselves as members, while the other two drives listed themselves as non-members. I tried going back to the old h57 mobo, and downgrading the raid drivers, but the issue remains. It's not port dependent, 2 of the drives always come up as non-members regardless of what port or motherboard they are plugged into. the screenshot should show that the SNs match, which begs the question why the software doesn't realize the drive is a member of the array: http://img837.imageshack.us/img837/6145/both.png I'd like to know if anyone has experienced anything similar, and what should i do, can i force the drive to be recognized as a member (without wiping data)?

    Read the article

  • Run 3 monitors on two different video cards?

    - by hullot
    Can I run 3 monitors on two different video cards? I have an ATI and Nvidia brand card. The ATI has 2 HDMI connections. They both work. Both cards are also picked up in Windows, one being the ATI and the other one as the Nvidia, but it says VGA Controller, although the card only takes 2 DVi. So, one DVI cable goes into that Nvidia card. 3 Monitors, but only 2 the HDMI ones from the ATI pick up, not the third one which is connected to the Nvidia via DVI. How can I run three monitors then? I suppose I can't install both drivers, so I'm unsure what to do. Is this possible? I just want the Nvidia card to power the third screen, no gaming on it, nothing. Also the ATI is picked up as primary card as well, so no hurdle there. EDIT: Hm, just installed the Nvidia drivers and it picked up the third screen no problem. Hope there aren't any major conflicts. Will post this as an answer as correct when I'm able. Can't as a new user.

    Read the article

  • Did Adobe Photoshop just killed my Graphics Card for good?

    - by user6004
    I was working with Adobe Photoshop, just some regular work, when I came to edit a PSD file and change the text of some layer, when all of a sudden the PC froze. No mouse, screen is frozen, keyboard strokes aren't getting me anything, no Task Manager, nada. So I rebooted my PC, and then something quite terrifying appeared before my eyes. It was not the Checkdisk utility that was launched, that made me terrified (by the way, that reboot damaged the partition table of an external HDD that was connected at the time to my PC, but that's another story). It was the screen itself. Please have a look. So after Checkdisk finished and Windows loaded, I noticed that the resolution was not right. Instead of 1440x900 which I had set, it was 1280x1024. When I went to change it back, I had no option to change back to my old resolution, and has only 3 other general resolution properties, as if my Video Card (GeForce 8800 GTS btw) was not recognized. And what do you know, in the Device Manager it appeared with an exclamation mark. Inside the hardware, it said this: Windows has stopped this device because it has reported problems. (Code 43) Uninstalling the drivers, downloading the newest drivers from NVIDIA and installing them did not work. It always comes back to this. So, do you have any advice before I go out and buy a new graphics card? I thought this was the only option left, but maybe the experts at Super User can help me out. By the way, the dotted screen appears after every reboot, and I see the dots when the ASUS Motherboard screen shows up at boot. Thanks in advance.

    Read the article

  • How can I get DVDs playing after a Vista to XP change?

    - by Liath
    I replaced my vista install on a Dell Inspiron 1525 with XP and have managed to get most things up and running again however I'm having trouble with playing DVDs. When I try and play a DVD I get the following message: Windows Media Player cannot play this DVD because there is a problem with digital copy protection between your DVD drive, decoder, and video card. Try installing an updated driver for your video card. I have ensured that my drive is configured to play Region 2 discs (I'm in the UK), I've installed the most up to date XP codec pack which makes me think it's a driver issue. In device manager I have got my DVD drivers up to date however under "Other Devices" I'm missing several which sound key: Audio Device on High Definition Audio Bus Modem Device on High Definition Audio Bus Video Controller Video Controller (VGA Compatible) However I've installed all the relevant drivers I can find on the Dell website. The drive itself is working - I've run software from the drive. I'm afraid I am far from a sys-admin so I'm struggling on this one. How can I get my DVDs playing again?

    Read the article

  • Ethernet cable unplugged after updating from windows 8.0 to 8.1

    - by Pehmolelu
    Yeah, so I went and updated my windows 8 pro to 8.1. Now everything else seems to work but the network. The Ethernet just says that Network cable is unplugged, even though it is plugged and I have tried different cord as well and I have tested that the router works. I have tried uninstalling the network drivers (Realtec PCIe GBE) and reinstall them with no success. After installing drivers the Device Management gives error for it "Device could not be started. Code 10" Before 8.1 update I had rt630x64.inf, after update it was netrt630x64.inf, and after installing the latest driver rt630x64.inf. With rt630x64.inf there isn't any error, but it's still not just working. New downloaded version: 8.020.0815.2013 (From Realtek website) The driver before: 8.1.510.2013 (After updating the windows to 8.1) I'm using Desktop PC, no VM. I dont have VirtualBox or Vmware installed. I have checked from BIOS that the card is enabled. I have booted in safe mode with network enabled. Says unplugged there as well. I have put the power off for few minutes and put back on, no effect. If anyone has any kind of suggestions, please tell.

    Read the article

  • Games on windows 8 in bootcamp lag even on lowest graphics

    - by Jackson Gariety
    I've been playing Crysis 2 and Skyrim on my Retina MacBookPro (10,1) for months now. The two games used to run super smoothly even on nearly maxed out settings. This laptop has an Nvidia GeForce GT 650M graphics card inside, it runs great. But I recently replaced my Windows 8 consumer preview with the retail copy, and since then, 3D games lag in this odd way, no matter what the graphics settings. Every second Skyrim and Crysis alternates between running smoothly and lagging. It's a cyclical lag that comes and goes like clockwork. I can turn the graphics down to 800x600 with no antialiasing and low texture quality, and it runs much smoother on the "up" motion of the cycle, but every second it moves back into this lag spike. I've tried installing beta graphics drivers, re installing the operating system, re installing the bootcamp support software, and freeing up space (I have about 20 GB free). I can't figure out what suddenly caused this other than some obscure difference between the consumer preview and the retail version. What can I try? Is my video card failing? Are there some other drivers I can install? This isn't normal lag from maxing out the card, it

    Read the article

  • strange raid5 issue: [closed]

    - by 8steve8
    ok so ive had a 4x2TB(samsung HD204UI w/firmware patch) raid5 array working normally for about a month. It was in a h57 gigabyte motherboard using the intel raid with windows 7 x64. Today I got an intel h67 motherboard, so I upgraded the intel raid drivers to 10.1.0.1008 from 9.6.0.1014, and I'm not sure if i checked after a reboot, but it caused no problems. I swapped in the new dh67 motherboard, and my array status was "failed". 2 of the 4 drives listed themselves as members, while the other two drives listed themselves as non-members. I tried going back to the old h57 mobo, and downgrading the raid drivers, but the issue remains. It's not port dependent, 2 of the drives always come up as non-members regardless of what port or motherboard they are plugged into. the screenshot should show that the SNs match, which begs the question why the software doesn't realize the drive is a member of the array: http://img837.imageshack.us/img837/6145/both.png I'd like to know if anyone has experienced anything similar, and what should i do, can i force the drive to be recognized as a member (without wiping data)?

    Read the article

  • Windows 8 Communication Sound Setting not working

    - by blackmastiff
    I've been having a problem on my new laptop recently which is familiar but baffling the usual fixes. I'm running Windows 8 with an onboard Realtek soundcard. It's similar to the one on my older computer running Windows 7. The problem is, when I'm in Skype or Mumble, Windows changes the sound output to lower everything else automatically. I've disabled the communications sound change option on the communications tab within sound devices and checked all the applications settings to insure that they are not responsible. They aren't, and I noticed something else. When I'm in the sound properties dialog, and I switch to the microphone tab, the same audio output reduction occurs. This seems to say to me that the microphone must be responsible in some way, but seeing as I uninstalled all the drivers and installed windows drivers instead, I'm confused as to why this would be occurring. Any thoughts? EDIT: I just tried disabling the built in microphone and the sound no longer get changed. More confused now? As soon as I turn it back on, the sound gets dropped again. Incidentally, the fix for this on windows 7 was this question: Windows 7 lowers applications' volume automatically I've got my computer set that way and it doesn't work.

    Read the article

  • Formatting a former RAID 0 drive through USB

    - by EXC
    I'll try to be as specific as possible here: I was using two Hitachi 2.5" 500 gb HDDs in my Gateway P-7805u laptop in a RAID 0 configuration. The array was causing the laptop to run extremely hot, however, so I removed them and deleted the RAID array through Intel Matrix HDD manager. I did a clean install of Windows 7 on the original 320 gb HDD that came with the laptop. I never did format the original RAID array HDDs before taking them out of the computer. Now, I am attempting to format the Hitachi 500 gb RAID array HDDs externally through a USB external enclosure. The external HDD drivers install on my clean install OS, but when I go into 'My Computer' there is no external drive available. I cannot format in CMD Prompt because my computer will not designate a drive letter to the external HDD. The drivers install and the HDD is recognized as a Hitachi external drive, but nothing seems to show up in my computer window. I need to know if there is a way to format these drives to NTFS externally.

    Read the article

  • How can I get DVDs playing after a Vista to XP change? [closed]

    - by Liath
    I replaced my vista install on a Dell Inspiron 1525 with XP and have managed to get most things up and running again however I'm having trouble with playing DVDs. When I try and play a DVD I get the following message: Windows Media Player cannot play this DVD because there is a problem with digital copy protection between your DVD drive, decoder, and video card. Try installing an updated driver for your video card. I have ensured that my drive is configured to play Region 2 discs (I'm in the UK), I've installed the most up to date XP codec pack which makes me think it's a driver issue. In device manager I have got my DVD drivers up to date however under "Other Devices" I'm missing several which sound key: Audio Device on High Definition Audio Bus Modem Device on High Definition Audio Bus Video Controller Video Controller (VGA Compatible) However I've installed all the relevant drivers I can find on the Dell website. The drive itself is working - I've run software from the drive. I'm afraid I am far from a sys-admin so I'm struggling on this one. How can I get my DVDs playing again?

    Read the article

  • Which Windows 8 tool should I use to "read", "upload", my Windows 7 latest backup DVD (is it possible?)

    - by Robert
    Which Windows 8 tool should I use to "read", "upload", my Windows 7 latest backup DVD (is it possible?). I've just installed W8 and haven't made any changes to my new ecosystem and, what happened was that, as I was managing my new drivers, some mess* occurred, I confess, and now what I have left is every single backup tool I made use of W7, like system images, restore dvds, backup up to date monthly and so on, and would like to keep in touch with W8. I'm one of those with problems managing the amd switchable gpu drivers. Now I want to stay with W8 (download version - didn't clean install) but with my old personal files. I don't care to programs updates. I got everything original on dvds, of my interest. Yesterday I tried refreshing W8 once but didn't work. Maybe trying again tonight. What would you guys do in my place, please? *the mess I am talking about is to have disabled my intel (the only driver left) gpu in device manager tool in W8. I got black screen on system boot. Cheers, C.C.

    Read the article

  • Windows 7 Upgrade Fail from Home Premium to Ultimate Professional

    - by Michael S-B
    I had a hard drive crash, which meant I had to install a new HDD in my Dell 64-Bit XPS 1350 (lovely computer). I had previously been running Windows 7 Ultimate Professional which I had upgraded from the OEM Win 7 Home Premium by means of a disk I purchased from my university. Using the Recovery disk from Dell I installed Windows 7 Home Premium successfully on the new hard drive, but when I have tried to upgrade via my disk to Ultimate it installs the whole thing, says its complete, but when I reboot, tells me: "This version of Windows could not be installed. Your previous version of Windows has been restored, and you can continue to use it." I've installed the drivers from Dell's driver disk, but still to no avail. I've also used Driver Robot to update all my drivers. I can't find a .dmp file anywhere under C:\$WINDOWS.~BT\Sources but I did find this file under C:\$WINDOWS.~BT\Sources\Panther. setupact.log https://www.dropbox.com/s/yzy7fhkxlzc235y/setupact.log If anyone could please advise me what I need to do to fix Windows so it will upgrade properly, I would greatly appreciate it.

    Read the article

  • Why are my USB 2.0 devices crashing Windows XP?

    - by BenAlabaster
    Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic ATX motherboard with no identifying markings other than one stamp that says "Rev.B". CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. On board it has 1 x 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors. It has a DVD+/-RW running as master on IDE1 and a 1.44Mb 3.5" floppy drive connected to the floppy connector. It has an 80Gb Western Digital hard drive running as master on IDE0. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. The hard disk is freshly formatted and built with Windows XP Professional/Service Pack 3 and is up to date with all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 hangs the whole machine as soon as it starts up, requiring a hard boot to recover). It's got a Daytek MV150 15" touch screen hooked up to the on board VGA and COM1 sockets with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem: If I hook any devices to the USB 2.0 sockets, it hangs the whole machine and I have to hard boot it to get it back up. If I have any devices attached to the USB 2.0 sockets when I boot up, it hangs before Windows gets to the login prompt and I have to hard boot it to recover. Workarounds found: I can plug the same devices into the on board USB 1.0 sockets and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions: I've seen suggestions that this could be a power problem - that the PSU just doesn't have the wattage to drive these ports. While I'm doubtful this is the problem [after all the motherboard has the same standard connector regardless of the PSU wattage], I tried disabling all the on board devices that I'm not using - on board LAN, the second COM port, the AGP connector etc. through the BIOS in what I'm sure is a futile attempt to reduce the power consumption... I also modified the ACPI and power management settings. It didn't have any noticeable affect, although it didn't do any harm either. Could the wattage of the PSU really cause this problem? If it can, is there anything I need to be aware of when replacing it or do I just need to make sure it's got a higher wattage than the current one? My interpretation was that the wattage only affected the number of drives you could hook up to the power connectors, is that right? I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself, and Windows says the card is installed and working correctly... right up until I connect a device to it. The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference - does anyone have any experience that would suggest this might work? Other thoughts/questions: Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question: Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine?

    Read the article

  • Why are my USB 2.0 devices hanging Windows XP?

    - by BenAlabaster
    Background on the machine I'm having a problem with: The machine was inherited and appears to be circa 2003 (there's a date stamp on the power supply which leads me to this conclusion). I've got it set up as a Skype terminal for my 2 year old to keep in touch with her grandparents and other members of the family - which everyone loves. It has a generic ATX motherboard with no identifying markings other than one stamp that says "Rev.B". CPU-Z identifies the motherboard model as VT8601 but doesn't provide me with any manufacturer name. On board it has 1 x 10/100 LAN, 2 x USB 1.0, VGA, PS/2 for KB and mouse, parallel port, 2 x serial ports, 2 x IDE, 1 x floppy, 2 x SDRAM slots, 1 x CPU housing that is seating a 1.3GHz Intel Celeron CPU, 3 x PCI, 1 x AGP - although you can only use 2 of the PCI slots if you use the AGP slot due to the physical layout of the board. It's got 768Mb PC133 SDRAM - 1 x 512Mb & 1 x 256Mb installed as well as a D-LINK WDA-2320 54G Wi-Fi network card and a generic USB 2.0 expansion board containing 3 x external + 1 x internal USB connectors - it has a NEC uPD720102 chipset. It has a DVD+/-RW running as master on IDE1 and a 1.44Mb 3.5" floppy drive connected to the floppy connector. It has an 80Gb Western Digital hard drive running as master on IDE0. All this is sitting in a slimline case. I don't know the wattage of the PSU, but can post this later if this proves to be helpful. The motherboard is running a version of Award BIOS for which I don't have the version number to hand but can again post this later if it would be helpful. The hard disk is freshly formatted and built with Windows XP Professional/Service Pack 3 and is up to date with all current patches. In addition to Windows XP, the only other software it's running is Skype 4.1 (4.2 hangs the whole machine as soon as it starts up, requiring a hard boot to recover). It's got a Daytek MV150 15" touch screen hooked up to the on board VGA and COM1 sockets with the most current drivers from the Daytek website and the most current version of ELO-Touchsystems drivers for the touch component. The webcam is a Logitech Webcam C200 with the latest drivers from the Logitech website. The problem: If I hook any devices to the USB 2.0 sockets, it hangs the whole machine and I have to hard boot it to get it back up. If I have any devices attached to the USB 2.0 sockets when I boot up, it hangs before Windows gets to the login prompt and I have to hard boot it to recover. Workarounds found: I can plug the same devices into the on board USB 1.0 sockets and everything works fine, albeit at reduced performance. I've tried 3 different kinds of USB thumb drives, 3 different makes/models of webcams and my iPhone all with the same effect. They're recognized and don't hang the machine when I hook them to the USB 1.0 but if I hook them to the USB 2.0 ports, the machine hangs within a couple of seconds of recognizing the devices were connected. Attempted solutions: I've seen suggestions that this could be a power problem - that the PSU just doesn't have the wattage to drive these ports. While I'm doubtful this is the problem [after all the motherboard has the same standard connector regardless of the PSU wattage], I tried disabling all the on board devices that I'm not using - on board LAN, the second COM port, the AGP connector etc. through the BIOS in what I'm sure is a futile attempt to reduce the power consumption... I also modified the ACPI and power management settings. It didn't have any noticeable affect, although it didn't do any harm either. Could the wattage of the PSU really cause this problem? If it can, is there anything I need to be aware of when replacing it or do I just need to make sure it's got a higher wattage than the current one? My interpretation was that the wattage only affected the number of drives you could hook up to the power connectors, is that right? I've installed the USB card in another machine and it works without issue, so it's not a problem with the USB card itself, and Windows says the card is installed and working correctly... right up until I connect a device to it. The only thing I haven't done which I only just thought of while writing this essay is trying the USB 2.0 card in a different PCI slot, or re-ordering the wi-fi and USB cards in the slots... although I'm not sure if this will make any difference - does anyone have any experience that would suggest this might work? Other thoughts/questions: Perhaps this is an incompatibility between the USB 2.0 card and the BIOS, would re-flashing the BIOS with a newer version help? Do I need to be able to identify the manufacturer of the motherboard in order to be able to find a BIOS edition specific for this motherboard or will any version of Award BIOS function in its place? Question: Does anyone have any ideas that could help me get my USB 2.0 devices hooked up to this machine? Edit: Updated the USB 2.0 info with reference to actual card - http://www.xpcgear.com/lpnec4u.html

    Read the article

< Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >