Search Results

Search found 9557 results on 383 pages for 'x86 64'.

Page 85/383 | < Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >

  • USB keyboard stopped working in Ubuntu with error -71

    - by tapan
    I have a usb keyboard which was working perfectly till now (about a year since i have been regularly using ubuntu). It suddenly stopped working. It stopped working when I connected a USB HDD. Now the keyboard works randomly .. working for a while and then stops working for a longer time. Here is the dmesg output : [ 705.817076] usb 5-1: device not accepting address 8, error -71 [ 705.928032] usb 5-1: new low speed USB device using uhci_hcd and address 9 [ 706.336060] usb 5-1: device not accepting address 9, error -71 [ 706.448055] usb 5-1: new low speed USB device using uhci_hcd and address 10 [ 706.568044] usb 5-1: device descriptor read/64, error -71 [ 706.792049] usb 5-1: device descriptor read/64, error -71 [ 707.008060] usb 5-1: new low speed USB device using uhci_hcd and address 11 [ 707.128041] usb 5-1: device descriptor read/64, error -71 [ 707.352052] usb 5-1: device descriptor read/64, error -71 [ 707.456068] hub 5-0:1.0: unable to enumerate USB device on port 1 Based on the suggestions here i tried the following two things: echo -1 > /sys/module/usbcore/parameters/autosuspend echo Y > /sys/module/usbcore/parameters/old_scheme_first However, i am still facing the same problem. Can anyone help me out with this ? I'm using Ubuntu 10.04 Lucid Lynx.

    Read the article

  • Why does cpuinfo report that my frequency is slower?

    - by Avery Chan
    My machine is running off of a AMD Sempron(tm) X2 190 Processor. According the marketing copy, it should be running at around 2.5 Ghz. Why is the cpu speed being reported as something lower? Spec description (in Chinese) $ cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 16 model : 6 model name : AMD Sempron(tm) X2 190 Processor stepping : 3 microcode : 0x10000c8 cpu MHz : 800.000 cache size : 512 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm 3dnowext 3dnow constant_tsc rep_good nopl nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt npt lbrv svm_lock nrip_save bogomips : 5022.89 TLB size : 1024 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm stc 100mhzsteps hwpstate processor : 1 vendor_id : AuthenticAMD cpu family : 16 model : 6 model name : AMD Sempron(tm) X2 190 Processor stepping : 3 microcode : 0x10000c8 cpu MHz : 800.000 cache size : 512 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 apicid : 1 initial apicid : 1 fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm 3dnowext 3dnow constant_tsc rep_good nopl nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt npt lbrv svm_lock nrip_save bogomips : 5022.82 TLB size : 1024 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm stc 100mhzsteps hwpstate

    Read the article

  • Where is vmlinux on my Ubuntu installation?

    - by Jason Baker
    I'm trying to work with starting up oprofile, and I'm running into a problem at this step: opcontrol --vmlinux=/path/to/vmlinux Ubuntu has no package called vmlinux, and when I do a locate vmlinux, I get a lot of files: /usr/src/linux-headers-2.6.28-14/arch/h8300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-14/arch/m68k/kernel/vmlinux-std.lds /usr/src/linux-headers-2.6.28-14/arch/m68k/kernel/vmlinux-sun3.lds /usr/src/linux-headers-2.6.28-14/arch/mn10300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-14/arch/sh/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-14/arch/x86/boot/compressed/vmlinux_32.lds /usr/src/linux-headers-2.6.28-14/arch/x86/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-14/include/asm-generic/vmlinux.lds.h /usr/src/linux-headers-2.6.28-15/arch/h8300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-15/arch/m68k/kernel/vmlinux-std.lds /usr/src/linux-headers-2.6.28-15/arch/m68k/kernel/vmlinux-sun3.lds /usr/src/linux-headers-2.6.28-15/arch/mn10300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-15/arch/sh/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-15/arch/x86/boot/compressed/vmlinux_32.lds /usr/src/linux-headers-2.6.28-15/arch/x86/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-15/include/asm-generic/vmlinux.lds.h /usr/src/linux-headers-2.6.28-16/arch/h8300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-16/arch/m68k/kernel/vmlinux-std.lds /usr/src/linux-headers-2.6.28-16/arch/m68k/kernel/vmlinux-sun3.lds /usr/src/linux-headers-2.6.28-16/arch/mn10300/boot/compressed/vmlinux.lds /usr/src/linux-headers-2.6.28-16/arch/sh/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-16/arch/x86/boot/compressed/vmlinux_32.lds /usr/src/linux-headers-2.6.28-16/arch/x86/boot/compressed/vmlinux_64.lds /usr/src/linux-headers-2.6.28-16/include/asm-generic/vmlinux.lds.h Which one of these is the one I'm looking for?

    Read the article

  • RTNETLINK answers: Invalid argument

    - by LinuxPenseur
    When my system boots up it shows the following message. Bringing up loopback interface: [ OK ] Bringing up interface eth0: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth1: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth2: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth3: RTNETLINK answers: Invalid argument [ OK ] Why is this happening. Normally it does not give the message RTNETLINK answers: Invalid argument I did ifconfig and the output is eth0 Link encap:Ethernet HWaddr 00:00:50:6D:56:B4 inet addr:120.0.10.137 Bcast:120.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b4/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:00:50:6D:56:B5 inet addr:121.0.10.137 Bcast:121.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xc000 eth2 Link encap:Ethernet HWaddr 00:00:50:6D:56:B6 inet addr:128.0.10.137 Bcast:128.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1006 (1006.0 b) TX bytes:396 (396.0 b) Interrupt:16 eth3 Link encap:Ethernet HWaddr 00:00:50:6D:56:B7 inet addr:123.0.10.137 Bcast:123.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:728 (728.0 b) TX bytes:396 (396.0 b) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:980 (980.0 b) TX bytes:980 (980.0 b) What could be the reason for the message and how to change this to normal? Thanks

    Read the article

  • ssh connection slow when using @hostname.com but now when using @ipaddress

    - by Alex Recarey
    When connecting to a Debian server using ssh, if I use [email protected] (the IP address of hte server) the connection is instant. If however I use [email protected] (a DNS redirected to the IP address of the server) the ssh connection hangs for a 20 seconds before connecting successfully. The ssh logs show the following: [alex@alex home]$ ssh -v -v [email protected] OpenSSH_5.5p1, OpenSSL 1.0.0c-fips 2 Dec 2010 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug2: ssh_connect: needpriv 0 and here it hangs during 20 seconds before continuing. I think it might have something to do with reverse DNS or similar (the server does not really "know" it's name is hostname.com, it just has that DNS rediriected to its IP address). I have added the following options to /etc/ssh/sshd_config: UseDNS no GSSAPIAuthentication no to no effect. The server's DNS records in /etc/resolv.conf are configured correctly: ping hostname.com PING sub.domain.com (X.X.X.X) 56(84) bytes of data. 64 bytes from replicant (X.X.X.X): icmp_seq=1 ttl=64 time=0.029 ms 64 bytes from replicant (X.X.X.X): icmp_seq=2 ttl=64 time=0.050 ms?s Thanks for the help. Solution: It seems the DSL router my ISP saddled me with was causing the trouble. Changing my DNS server from 192.168.1.1 (router's IP) to google's (8.8.8.8, always good to know when you are in a hurry) instantly solved the connection delay problem. I am guessing that the 50€ router provided does not cache DNS entries, although I don't understand why pinging the DNS address had no delay, and 20 seconds is too long of a wait, even for uncached DNS. Tnanks again for the help!

    Read the article

  • Why can't I route to some sites from my MacBook Pro that I can see from my iPad?

    - by Robert Atkins
    I am on M1 Cable (residential) broadband in Singapore. I have an intermittent problem routing to some sites from my MacBook Pro—often Google-related sites (arduino.googlecode.com and ajax.googleapis.com right now, but sometimes even gmail.com.) This prevents StackExchange chat from working, for instance. Funny thing is, my iPad can route to those sites and they're on the same wireless network! I can ping the sites, but not traceroute to them which I find odd. That I can get through via the iPad implies the problem is with the MBP. In any case, calling M1 support is... not helpful. I get the same behaviour when I bypass the Airport Express entirely and plug the MBP directly into the cable modem. Can anybody explain a) how this is even possible and b) how to fix it? mella:~ ratkins$ ping ajax.googleapis.com PING googleapis.l.google.com (209.85.132.95): 56 data bytes 64 bytes from 209.85.132.95: icmp_seq=0 ttl=50 time=11.488 ms 64 bytes from 209.85.132.95: icmp_seq=1 ttl=53 time=13.012 ms 64 bytes from 209.85.132.95: icmp_seq=2 ttl=53 time=13.048 ms ^C --- googleapis.l.google.com ping statistics --- 3 packets transmitted, 3 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 11.488/12.516/13.048/0.727 ms mella:~ ratkins$ traceroute ajax.googleapis.com traceroute to googleapis.l.google.com (209.85.132.95), 64 hops max, 52 byte packets traceroute: sendto: No route to host 1 traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 *traceroute: sendto: No route to host traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 ^C mella:~ ratkins$ The traceroute from the iPad goes (and I'm copying this by hand): 10.0.1.1 119.56.34.1 172.20.8.222 172.31.253.11 202.65.245.1 202.65.245.142 209.85.243.156 72.14.233.145 209.85.132.82 From the MBP, I can't traceroute to any of the IPs from 172.20.8.222 onwards. [For extra flavour, not being able to access the above appears to stop me logging in to Server Fault via OpenID and formatting the above traceroutes correctly. Anyone with sufficient rep here to do so, I'd be much obliged.]

    Read the article

  • can't install mysql-devel on centos 6.5

    - by Latheesan Kanes
    I need mysql-devel package to be installed on my CentOS 6.5 running Percona 5.5 (already installed & running). When I try to install the devel package like this: yum --enablerepo=remi install mysql-devel I get the following error: Error: Package: mysql-devel-5.5.37-1.el6.remi.i686 (remi) Requires: real-mysql-libs(x86-32) = 5.5.37-1.el6.remi Available: mysql-libs-5.5.36-1.el6.remi.i686 (remi) real-mysql-libs(x86-32) = 5.5.36-1.el6.remi Available: mysql-libs-5.5.37-1.el6.remi.i686 (remi) real-mysql-libs(x86-32) = 5.5.37-1.el6.remi Error: Package: mysql-5.5.37-1.el6.remi.i686 (remi) Requires: real-mysql-libs(x86-32) = 5.5.37-1.el6.remi Available: mysql-libs-5.5.36-1.el6.remi.i686 (remi) real-mysql-libs(x86-32) = 5.5.36-1.el6.remi Available: mysql-libs-5.5.37-1.el6.remi.i686 (remi) real-mysql-libs(x86-32) = 5.5.37-1.el6.remi Error: mysql conflicts with Percona-Server-client-55-5.5.37-rel35.0.el6.i686 Here's what's currently installed on my server: [root@server1 ~]# yum list installed | grep mysql php-mysqlnd.i686 5.4.29-1.el6.remi @remi [root@server1 ~]# yum list installed | grep percona Percona-Server-client-55.i686 5.5.37-rel35.0.el6 @percona Percona-Server-server-55.i686 5.5.37-rel35.0.el6 @percona Percona-Server-shared-55.i686 5.5.37-rel35.0.el6 @percona [root@server1 ~]# Any ideas how to fix this dependency error?

    Read the article

  • DL380 G7: Not able to access ILO on DL380 via ssh from a client

    - by user117140
    I have problem where I can't access my ILO(ssh to ILO IP) thru client which is in different network.I am able to ping ILO IP thru this clinet but ssh access is not possible. Is it possible to have ssh to ILO IP from a client which is in different network? FYI, from the same client I can do ssh to server application IP but ssh to this server ILO IP is not possible. Kindly help? Some more info added: ILO IP address is 10.247.172.70 and its VLAN is different than Client VLAN. Client IP address is 10.247.167.80. ping to ILO IP from this client is possible but not ssh. I can do ssh to ILO IP if I try to do it from the server(hostname:node1) having ILO port or from the other node of this cluster itself,So ssh login is enabled. [root@node1 ~]$ssh -v 10.247.173.70 OpenSSH_4.3p2, OpenSSL 0.9.8e-fips-rhel5 01 Jul 2008 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to 10.247.173.70 [10.247.173.70] port 22. [root@node1 ~]$ping 10.247.173.70 PING 10.247.173.70 (10.247.173.70) 56(84) bytes of data. 64 bytes from 10.247.173.70: icmp_seq=1 ttl=254 time=0.283 ms 64 bytes from 10.247.173.70: icmp_seq=2 ttl=254 time=0.344 ms 64 bytes from 10.247.173.70: icmp_seq=3 ttl=254 time=0.324 ms 64 bytes from 10.247.173.70: icmp_seq=4 ttl=254 time=0.367 ms

    Read the article

  • Why can't I route to some sites from my MacBook Pro that I can see from my iPad? [closed]

    - by Robert Atkins
    I am on M1 Cable (residential) broadband in Singapore. I have an intermittent problem routing to some sites from my MacBook Pro—often Google-related sites (arduino.googlecode.com and ajax.googleapis.com right now, but sometimes even gmail.com.) This prevents StackExchange chat from working, for instance. Funny thing is, my iPad can route to those sites and they're on the same wireless network! I can ping the sites, but not traceroute to them which I find odd. That I can get through via the iPad implies the problem is with the MBP. In any case, calling M1 support is... not helpful. I get the same behaviour when I bypass the Airport Express entirely and plug the MBP directly into the cable modem. Can anybody explain a) how this is even possible and b) how to fix it? mella:~ ratkins$ ping ajax.googleapis.com PING googleapis.l.google.com (209.85.132.95): 56 data bytes 64 bytes from 209.85.132.95: icmp_seq=0 ttl=50 time=11.488 ms 64 bytes from 209.85.132.95: icmp_seq=1 ttl=53 time=13.012 ms 64 bytes from 209.85.132.95: icmp_seq=2 ttl=53 time=13.048 ms ^C --- googleapis.l.google.com ping statistics --- 3 packets transmitted, 3 packets received, 0.0% packet loss round-trip min/avg/max/stddev = 11.488/12.516/13.048/0.727 ms mella:~ ratkins$ traceroute ajax.googleapis.com traceroute to googleapis.l.google.com (209.85.132.95), 64 hops max, 52 byte packets traceroute: sendto: No route to host 1 traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 *traceroute: sendto: No route to host traceroute: wrote googleapis.l.google.com 52 chars, ret=-1 ^C mella:~ ratkins$ The traceroute from the iPad goes (and I'm copying this by hand): 10.0.1.1 119.56.34.1 172.20.8.222 172.31.253.11 202.65.245.1 202.65.245.142 209.85.243.156 72.14.233.145 209.85.132.82 From the MBP, I can't traceroute to any of the IPs from 172.20.8.222 onwards. [For extra flavour, not being able to access the above appears to stop me logging in to Server Fault via OpenID and formatting the above traceroutes correctly. Anyone with sufficient rep here to do so, I'd be much obliged.]

    Read the article

  • RTNETLINK answers: Invalid argument

    - by LinuxPenseur
    Hi, When my system boots up it shows the following message. Bringing up loopback interface: [ OK ] Bringing up interface eth0: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth1: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth2: RTNETLINK answers: Invalid argument [ OK ] Bringing up interface eth3: RTNETLINK answers: Invalid argument [ OK ] Why is this happening. Normally it does not give the message RTNETLINK answers: Invalid argument I did ifconfig and the output is eth0 Link encap:Ethernet HWaddr 00:00:50:6D:56:B4 inet addr:120.0.10.137 Bcast:120.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b4/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xa000 eth1 Link encap:Ethernet HWaddr 00:00:50:6D:56:B5 inet addr:121.0.10.137 Bcast:121.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:3 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:214 (214.0 b) Base address:0xc000 eth2 Link encap:Ethernet HWaddr 00:00:50:6D:56:B6 inet addr:128.0.10.137 Bcast:128.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b6/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1006 (1006.0 b) TX bytes:396 (396.0 b) Interrupt:16 eth3 Link encap:Ethernet HWaddr 00:00:50:6D:56:B7 inet addr:123.0.10.137 Bcast:123.0.255.255 Mask:255.255.255.0 inet6 addr: fe80::200:50ff:fe6d:56b7/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:728 (728.0 b) TX bytes:396 (396.0 b) Interrupt:17 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:980 (980.0 b) TX bytes:980 (980.0 b) What could be the reason for the message and how to change this to normal? Thanks

    Read the article

  • Autohotkey script multiple functions

    - by Vince
    Is it possible to use this bottom script but add a second hotkey and function that goes with it. ;DoOver.ini ;[Settings] ;record={LCtrl}{F12} ;hotkey to start and stop recording ;playback={LCtrl}{F5} ;hotkey to start playback ;keydelay=10 ;ms to wait after sending a keypress ;windelay=100 ;ms to wait after activating a window ;movemouseafter=1 ;move the mouse to original pos after playback 1=yes 0=no [Settings] record={LCtrl}{F12} playback={LCtrl}{F5} keydelay=10 windelay=100 movemouseafter=1 macro={WinActive}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{LCTRL Down}{Right}{Right}{LCTRL Up}{LSHIFT Down}{End}{LSHIFT Up}{LCTRL Down}{c}{LCTRL Up}{MouseClick,L,236,116,1,0,D}{MouseClick,L,54,116,1,0,U}{LCTRL Down}{LCTRL Up}{MouseClick,L,474,64,1,0,D}{MouseClick,L,474,64,1,0,U}{MouseClick,L,451,77,1,0,D}{MouseClick,L,451,77,1,0,U}{MouseClick,L,44,225,1,0,D}{MouseClick,L,44,225,1,0,U} OR playback={LCtrl}{F7} keydelay=10 windelay=100 movemouseafter=1 macro={WinActive}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{Down}{LCTRL Down}{Right}{Right}{LCTRL Up}{LSHIFT Down}{End}{LSHIFT Up}{LCTRL Down}{c}{LCTRL Up}{MouseClick,L,236,116,1,0,D}{MouseClick,L,54,116,1,0,U}{LCTRL Down}{LCTRL Up}{MouseClick,L,474,64,1,0,D}{MouseClick,L,474,64,1,0,U}{MouseClick,L,451,77,1,0,D}{MouseClick,L,451,77,1,0,U}{MouseClick,L,44,225,1,0,D}{MouseClick,L,44,225,1,0,U} Maybe add something like what is printed in bold here. I know the coding isnt right here, but i think this is the best way to describe what I am looking for. Anybody?

    Read the article

  • OpenVPN IPV6 Tunnel Radvd

    - by Arenstar
    Hello.. I have an interesting question regarding ipv6 + openvpn.. My Version is OpenVPN 2.1.1 i have been given a native /64 ipv6 network ( for this example 2001:acb:132:acb::/64 ) The plan was/is, route this block through openvpn and into an office ( for testing purposes ) Soo to explain.. I have a Centos Box as the first linux "router" in a datacenter & a Ubuntu box as the second linux "router" in the office I have created a simple point-to-point tunnel using tun ( based off ipv4 address to start the tunnel ) I have assigned to Centos /sbin/ip addr add fed1::1/128 dev eth0 /sbin/ip addr add fed2::2/128 dev tun0 /sbin/ip route add 2001:acb:132:acb::/64 dev tun0 ## ipv6 Block down the tunnel /sbin/ip route add ::/0 dev eth0 ## Default out to Gateway I have assigned to Ubuntu /sbin/ip addr add fed1::3/128 dev tun0 /sbin/ip addr add fed1::4/128 dev eth0 /sbin/ip route add 2001:acb:132:acb::/64 dev eth0 ## ipv6 Block down to eth0 /sbin/ip route add ::/0 dev tun0 ## Default up the tunnel I have also included on both servers.. sysctl -w net.inet6.ip6.forwarding=1 Looks Good... right??? Wrong.. :( I am not able to ping fed1::1 from fed1::4 (Ubuntu) (can ping :4,:3,:2) However, i can ping fed1::1 fed1::2 from :3 ?????? ( very strange ) I am able to access the internet from any ipv6 interface on the Centos Box but clearly not from the Ubuntu box.. Further, i will eventually run radvd on the Ubuntu box eth0, and autoconf the network with ipv6 address's Anyone with some advice / tips to help me out.. ??? Cheers

    Read the article

  • Can any postfix guru assist me determine how emails are still being sent via my server from unauthorized sources?

    - by Dave
    Hi all, I'm getting a little concerned as I run a small server hosting a number of websites and manage the email for a few dozen people. Just recently though I've had a couple of notifications from spamcop alerting me that spam has been sent from my server, and when I have a look over the logs from time to time I can indeed see that there are many repeated attempts of mail being sent from my server. Most of the time it gets knocked back from the destination servers but sometimes its getting through. Unfortunately I'm not linux or postfix expert, I can get by but had though I had my machine locked down quite securely, I don't allow relaying, when I check the online DNS/MX tools they tend to report my server as being OK so I'm not sure where to take it now and hoping someone might be able to throw me a few pointers. I get lots of entries like this in my MAIL.INFO log Jan 2 08:39:34 Debian-50-lenny-64-LAMP postfix/qmgr[15993]: 66B88257C12F: from=<>, size=3116, nrcpt=1 (queue active) Jan 2 08:39:34 Debian-50-lenny-64-LAMP postfix/qmgr[15993]: 614C2257C1BC: from=<[email protected]>, size=2490, nrcpt=3 (queue active) and Jan 7 16:09:37 Debian-50-lenny-64-LAMP postfix/error[6471]: 0A316257C204: to=<[email protected]>, relay=none, delay=384387, delays=384384/3/0/0.01, dsn=4.0.0, status=deferred (delivery temporarily suspended: host mx.fakemx.net[46.4.35.23] refused to talk to me: 421 mx.fakemx.net Service Unavailable) Jan 7 16:09:37 Debian-50-lenny-64-LAMP postfix/error[6470]: 5848C257C20D: to=<[email protected]>, relay=none, delay=384373, delays=384370/3/0/0.01, dsn=4.0.0, status=deferred (delivery temporarily suspended: host mx.fakemx.net[46.4.35.23] refused to talk to me: 421 mx.fakemx.net Service Unavailable) then there tends to be connection timeouts, so from what I see even though I had relaying disabled.. something is getting by and trying to send.. So if you can help that will be greatly appreciated, and any further logging/config info I can supply. Thanks

    Read the article

  • convert decrypted .vobs to .avi with ffmpeg on ubuntu

    - by Arcath
    I have a .vob file that has bee ripped from a dvd, when I watch the .vob its very good quality video and 5.1 english audio but when I use ffmpeg it has rubbish video and mono french audio. That was using this command: ffmpeg -i /samba/ripping/vobs/12161840#2.vob -f avi /samba/ripping/avis/test.avi I've tried a few different variations on that but it never comes back with anything good just bigger files with bad video and incorrect sound. I know the videos good and the correct audio streams exist so how do I select a 5.1 track and get good video? ffmpeg gives the .vob details as: Input #0, mpeg, from '/samba/ripping/vobs/12161840#2.vob': Duration: 00:42:05.56, start: 0.287267, bitrate: 5738 kb/s Stream #0.0[0x1e0]: Video: mpeg2video, yuv420p, 720x576 [PAR 64:45 DAR 16:9], 8436 kb/s, 25 fps, 25 tbr, 90k tbn, 50 tbc Stream #0.1[0x80]: Audio: ac3, 48000 Hz, 5.1, s16, 384 kb/s Stream #0.2[0x81]: Audio: ac3, 48000 Hz, 5.1, s16, 384 kb/s Stream #0.3[0x82]: Audio: ac3, 48000 Hz, mono, s16, 192 kb/s Output #0, avi, to '/samba/ripping/avis/test.avi': Metadata: ISFT : Lavf52.64.2 Stream #0.0: Video: mpeg4, yuv420p, 720x576 [PAR 64:45 DAR 16:9], q=2-31, 200 kb/s, 25 tbn, 25 tbc Stream #0.1: Audio: mp2, 48000 Hz, mono, s16, 64 kb/s Stream mapping: Stream #0.0 -> #0.0 Stream #0.3 -> #0.1

    Read the article

  • Windows 7, going crazy with environment variables

    - by roymustang86
    So, I am trying to learn java. I installed the JDK and proceeded to write a few programs. Each time, I have to give the path to javac.exe to compile the .java file. SO, I decided to tweak the %PATH% variable. And no matter what I change it to, it doesn't work. when I do an echo %PATH%, I get 'Program' is not recognized as an internal or external command, operable program or batch file. This is my Path variable contents : C:\app\product\11.1.0\client_1\bin;%CommonProgramFiles%\Microsoft Shared\Windows Live;%SystemRoot%\system32;%SystemRoot%;%SystemRoot%\System32\Wbem;%SYSTEMROOT%\System32\WindowsPowerShell\v1.0\;"C:\Program Files (x86)\Common Files\Roxio Shared\DLLShared\";"C:\Program Files\Broadcom\Broadcom 802.11";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\DLLShared\";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\DLLShared\";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\12.0\DLLShared\";"C:\Program Files (x86)\Roxio\OEM\AudioCore\";"C:\Program Files (x86)\Intel\Services\IPT\" How do I work around this? the double quotes were not there before, I added it thinking the space was the problem.

    Read the article

  • How to get Synergy working on Ubuntu 11.10 and Windows 7?

    - by Linda
    I'm using Ubuntu 11.10 32-bit and Windows 7 64-bit, however, Synergy only works when a window (application or folder) is open and touching the edge of the screen where the mouse should "jump". In other words, if a window is open and maximized, Synergy works normally. Without any windows, the mouse does not jump to the other screen. My steps: (Ubuntu) apt-get install -y quicksynergy (Windows) Install Synergy (I've tried both 1.3.8 and 1.4.8 and both 32 and 64-bit) On Ubuntu 11.10 32-bit (Synergy Server config): ~/.quicksynergy/synergy.conf section: screens myubuntu: mywin7: end section: links myubuntu: right = mywin7 mywin7: left = myubuntu end On Ubuntu 11.10 32-bit: $ /usr/bin/synergys -f --config .quicksynergy/synergy.conf ... 2012-04-25T14:04:12 NOTE: client "mywin7" has connected /build/buildd/synergy-1.3.6/lib/server/CServer.cpp,287 (output hangs here) On Windows 7 64-bit: Synergy 1.3.8 Client on Microsoft Windows 7 x86 (WOW64) started client connecting to 'myubuntu': ###.###.###.###:24800 connected to server (output hangs here) At this point, things should work, but my mouse still can't change screens unless a window is maximized on my Ubuntu machine. Everything is running on port 24800. No firewall on Ubuntu. Firewall port 24800 open on Windows 7. This was previously working on Ubuntu 10.10 and Windows 7 (so only Ubuntu has been upgraded). I'm open to using either 32 or 64-bit on either server or client side, but I just want to get it working on Ubuntu 11.10 and Windows 7! I'm also using Ubuntu Classic (no effects), and not Unity.

    Read the article

  • ubuntu dmidecode is not functioning properly

    - by Alaa Alomari
    dmidecode is giving irrelevant and conflicted results. it shows that i have two slots while the correct is 8 (the board is Tyan S5350.) uname -a Linux synd01 3.0.0-16-server #29-Ubuntu SMP Tue Feb 14 13:08:12 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux root@synd01:/home/badmin# dmidecode -t 16 dmidecode 2.9 SMBIOS 2.33 present. Handle 0x0011, DMI type 16, 15 bytes Physical Memory Array Location: System Board Or Motherboard Use: System Memory Error Correction Type: None Maximum Capacity: 4 GB Error Information Handle: Not Provided Number Of Devices: 2 while root@synd01:/home/badmin# dmidecode -t 17 | grep Size Size: No Module Installed Size: No Module Installed Size: 1024 MB Size: 1024 MB Size: No Module Installed Size: No Module Installed Size: 1024 MB Size: 1024 MB also lshw shows: *-memory description: System Memory physical id: 11 slot: System board or motherboard size: 4GiB *-bank:0 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 0 slot: J3B1 clock: 166MHz (6.0ns) *-bank:1 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 1 slot: J3B3 clock: 166MHz (6.0ns) *-bank:2 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 2 slot: J2B2 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) *-bank:3 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 3 slot: J2B4 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) *-bank:4 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 4 slot: J3B2 clock: 166MHz (6.0ns) *-bank:5 description: DIMM DDR Synchronous 166 MHz (6.0 ns) [empty] physical id: 5 slot: J2B1 clock: 166MHz (6.0ns) *-bank:6 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 6 slot: J2B3 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) *-bank:7 description: DIMM DDR Synchronous 166 MHz (6.0 ns) physical id: 7 slot: J1B1 size: 1GiB width: 64 bits clock: 166MHz (6.0ns) what might cause this conflict and how can i fix it? Thanks

    Read the article

  • IRC server connecting to another server

    - by Oxinabox
    I'm setting up an IRC server using IRC-Hybrid, I want my server to connect to another server, so that people on my server can connect to channels on that other server. I know this can be done, the GIMP IRC, is the same as the GNOME IRC My ircd.conf contains the following: connect { name = "aabstractname"; host = "128.64.2.1; send_password = "somepass"; accept_password = "somepass"; encrypted = no; port = 6667; class = "server"; autoconn = yes; compressed = yes; fakename = "irc.sd.dom.asn.au"; }; So when i run: /etc/init.d/ircd-hybrid restart it should be connecting to 128.64.2.1, but the log on 128.64.2.1, doesn't show anything Do I need entry on the host 128.64.2.1? I can't find any documentation for ircd.conf I'ld really like that documentation so I can check all my settings are right.

    Read the article

  • CentOS 6.3 Virtual under OpenVZ cannot ping, host lookups, outbound connections while postfix running

    - by Paul Cravey
    My best theory is that some kernel limit is being hit preventing outbound connections. We have tried basically everything from tcpdumps to provisioning an entirely new virtual server (we do not have this problem on any other virtuals), however the problem somehow carried over, even with new postfix build (working). Emails work, and outbound connections work, so long as postfix does not have too much going on. /proc/user_beancounters shows no limits being hit (show below). Nevertheless, pings fail even to IP addresses. TCP stack appears healthy. Load is low. No iowait. Flushed iptables already. Has anyone experienced anything like this? uid resource held maxheld barrier limit failcnt 3: kmemsize 166216365 170262528 9223372036854775807 9223372036854775807 0 lockedpages 0 0 9223372036854775807 9223372036854775807 0 privvmpages 285727 351885 9223372036854775807 9223372036854775807 0 shmpages 16933 17605 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 numproc 150 303 9223372036854775807 9223372036854775807 0 physpages 314156 326191 0 1280000 0 vmguarpages 0 0 9223372036854775807 9223372036854775807 0 oomguarpages 165355 165355 9223372036854775807 9223372036854775807 0 numtcpsock 89 172 9223372036854775807 9223372036854775807 0 numflock 22 76 9223372036854775807 9223372036854775807 0 numpty 1 2 9223372036854775807 9223372036854775807 0 numsiginfo 0 75 9223372036854775807 9223372036854775807 0 tcpsndbuf 2733472 4371752 9223372036854775807 9223372036854775807 0 tcprcvbuf 1798336 5427296 9223372036854775807 9223372036854775807 0 othersockbuf 491120 1000760 9223372036854775807 9223372036854775807 0 dgramrcvbuf 0 238728 9223372036854775807 9223372036854775807 0 numothersock 361 505 9223372036854775807 9223372036854775807 0 dcachesize 135941831 136114679 9223372036854775807 9223372036854775807 0 numfile 2905 4990 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 8 9 9223372036854775807 9223372036854775807 0 [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. --- 4.2.2.1 ping statistics --- 9 packets transmitted, 0 received, 100% packet loss, time 8493ms [root@bni /]# service postfix stop [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. 64 bytes from 4.2.2.1: icmp_seq=1 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=2 ttl=53 time=8.62 ms 64 bytes from 4.2.2.1: icmp_seq=3 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=4 ttl=53 time=8.66 ms Outbound connections of all sorts fail when postfix is running.

    Read the article

  • ipv6 reverse DNS delegation

    - by user1709492
    I currently have 2001:1973:2303::/48 assigned to me and i'll be assigning /64's to customer's I'd like to have 1 zonefile for the /48 where i can essentially point / redirect query to different nameservers. Example ( Desired effect ) 2001:1973:2303:1234::/64 -> ns1.example.com, ns2.example.com 2001:1973:2303:2345::/64 -> ns99.example2.com, ns100.example2.com 2001:1973:2303:4321::/64 -> ns1.cust1.com, ns2.cust1.com Current /48 zonefile $TTL 3h $ORIGIN 3.0.3.2.3.7.9.1.1.0.0.2.ip6.arpa. @ IN SOA ns3.example.ca. ns4.example.ca. ( 2011071030 ; serial 3h ; refresh after 3 hours 1h ; retry after 1 hour 1w ; expire after 1 week 1h ) ; negative caching TTL of 1 hour IN NS ns3.example.ca. IN NS ns4.example.ca. 1234 IN NS ns1.example.com. NS ns2.example.com. 2345 IN NS ns99.example2.com. NS ns100.example2.com. 4321 IN NS ns1.cust1.com. NS ns2.cust1.com. Where am i going wrong ? My request seems simple to me atleast. To put it in terms of firewalling i want to redirect traffic client queries 2001:1973:2303:4321::1 - ns3.example.ca sees the request and redirects the query to ns1.cust1.com - ns1.cust1.com answers the query with omg.itworks.ca ( provided ns1.cust1.com is properly configured.

    Read the article

  • Advertise a subnet route with radvd

    - by Thomas Berger
    we have set up a small IPv6 Testing network. The setup looks like this: ::/0 +----------+ | Firewall | Router to the public net +----------+ | 2001:...::/106 | +----------+ +-------| SIT GW | sit Tunnel gatway to the some test users | +----------+ | +----------+ | Test Sys | Testsystem +----------+ The idea is to advertise the default route from the firewall and the route for the SIT subnets from the sit gateway. The configurations for radvd are: # Firewall interface eth0 { AdvSendAdvert on; route ::/0 { }; }; # SIT Gatway interface eth0 { AdvSendAdvert on; route 2001:...::/106 { }; }; We have captured the adv. packages with tcpdump and the packages looks good. We see a default route from the fw, and the subnet route from the SIT gatway. But if we look on the testsystem there are two default routes over both gateways. There is no subnet route. The routing does not work of course. Here the routes we get: 2001:.....::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 fe80::/64 dev eth0 proto kernel metric 256 mtu 1500 advmss 1440 hoplimit 4294967295 default via fe80::baac:6fff:fe8e:XXXX dev eth0 proto kernel metric 1024 expires 0sec mtu 1500 advmss 1440 hoplimit 64 default via fe80::e415:aeff:fe12:XXXX dev eth0 proto kernel metric 1024 expires 0sec mtu 1500 advmss 1440 hoplimit 64 Any Idea?

    Read the article

  • Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit

    - by Gleeson9
    Pre-note: This is not a problem I am having with Minecraft. All answers I can find seem to be Minecraft issues. Error: could not create the Java Virtual Machine. Error: A fatal exception has occurred. Program will exit. I get this error when I try to do something Java related. I cannot launch a .jar without this error coming up and when I try to install JDK, I get this error. This has been plauging me for a while and I was not able to research an answer so I thought I would ask it myself. EDIT: Windows 7 (x64) Dell Studio Laptop, 4GB RAM, external Radeon HD 6950 Graphics Card. I have tried uninstalling all JVMs and reinstalling but it didn't work, although I cannot remember how thorough I was so I may try again. Here is a list of all the Java related things I have installed (found in the uninstall or change programs window): Java 3D 1.5.1 Java 3D 1.5.1 (x64) Java 3D 1.5.2 Java 6 Update 30 Java 6 Update 30 (64-bit) Java 7 Update 2 Java 7 Update 3 (64-bit) JavaFX 2.0.3 (64-bit) JavaFX 2.0.3 SDK (64-bit)

    Read the article

  • Path Environmental Variable errors

    - by roymustang86
    So, I am trying to learn java. I installed the JDK and proceeded to write a few programs. Each time, I have to give the path to javac.exe to compile the .java file. SO, I decided to tweak the %PATH% variable. And no matter what I change it to, it doesn't work. when I do an echo %PATH%, I get 'Program' is not recognized as an internal or external command, operable program or batch file. This is my Path variable contents : C:\app\product\11.1.0\client_1\bin;%CommonProgramFiles%\Microsoft Shared\Windows Live;%SystemRoot%\system32;%SystemRoot%;%SystemRoot%\System32\Wbem;%SYSTEMROOT%\System32\WindowsPowerShell\v1.0\;"C:\Program Files (x86)\Common Files\Roxio Shared\DLLShared\";"C:\Program Files\Broadcom\Broadcom 802.11";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\DLLShared\";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\DLLShared\";"C:\Program Files (x86)\Common Files\Roxio Shared\OEM\12.0\DLLShared\";"C:\Program Files (x86)\Roxio\OEM\AudioCore\";"C:\Program Files (x86)\Intel\Services\IPT\" How do I work around this? the double quotes were not there before, I added it thinking the space was the problem.

    Read the article

  • Proper configuration for Windows SMTP Virtual Server to only send email from localhost, and tracking down source of spam emails

    - by ilasno
    We manage a server that is hosted on Amazon EC2, which has web applications that need to be able to send outgoing email. Recently we received a notice from Amazon about possible email abuse on that server, so i've been looking into it. It's Windows Server Datacenter (2003, i guess), and uses SMTP Virtual Server (you know, the one that requires IIS 6 for admin). The settings on the Access tab are as follows: - Authentication: Anonymous - Connection: Only from 3 ip addresses (127.0.0.1 and 2 others that refer to that server) - Relay: Only from 3 ip addresses (127.0.0.1 and 2 others that refer to that server) In the SMTP logs there are many entries like the following: 2012-02-08 23:43:56 64.76.125.151 OutboundConnectionCommand SMTPSVC1 FROM: 0 0 4 0 26364 SMTP - - - - 2012-02-08 23:43:56 64.76.125.151 OutboundConnectionResponse SMTPSVC1 250+ok 0 0 6 0 26536 SMTP - - - - 2012-02-08 23:43:56 64.76.125.151 OutboundConnectionCommand SMTPSVC1 TO: 0 0 4 0 26536 SMTP - - - - 2012-02-08 23:43:56 64.76.125.151 OutboundConnectionResponse SMTPSVC1 250+ok 0 0 6 0 26707 SMTP - - - - ([email protected] is sending quite a lot of emails :-/) Can anyone confirm if the SMTP server settings seem correct? I'm also wondering if a web application on the machine could be exposing a contact form or something that would allow this sort of abuse, looking into that (and how to look into that) further.

    Read the article

  • Nginx Server Block Not Working? - Already running other vhosts just this one not working

    - by daveaspinall
    Im running a Debian 6 LEMP server with multiple virtual hosts and everything has been fine for 5 or so sites. But I've just tried adding another but for some reason it's just not working. By not working I mean in Chrome I get the "Oops! Google Chrome could not connect to subdomain.domain.net" error. I've changed the domain for security to subdomain.example.com and the IP is masked. Hosts file (I have multiple sub domains): xxx.xxx.xx.xxx *.example.com *.example Server Block: server { listen 80; server_name subdomain.example.com; access_log /srv/www/subdomain.example.com/logs/access.log; error_log /srv/www/subdomain.example.com/logs/error.log; root /srv/www/subdomain.example.com/public_html; location / { index index.html index.htm index.php; } location ~ \.php$ { include fastcgi_params; fastcgi_pass 127.0.0.1:9000; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; } } I've created the system link to the file in the /etc/nginx/sites-enabled/ directory and restarted/reloaded nginx. DNS seems fine: # ping -c 2 subdomain PING subdomain.example.com (xxx.xxx.xx.xxx) 56(84) bytes of data. 64 bytes from www.example.com (xxx.xxx.xx.xxx): icmp_req=1 ttl=64 time=0.035 ms 64 bytes from www.example.com (xxx.xxx.xx.xxx): icmp_req=2 ttl=64 time=0.048 ms Checking the file with cURL works: # curl http://subdomain.example.com HTML - OK Emptied browser cache but still no dice. Anything I'm missing? Like I mentioned, I have a few sites running fine on the server currently so php-fpm etc etc are working. Any help would be much appreciated! Cheers, Dave

    Read the article

< Previous Page | 81 82 83 84 85 86 87 88 89 90 91 92  | Next Page >