Search Results

Search found 8983 results on 360 pages for 'active attr'.

Page 89/360 | < Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >

  • How do I align my partition table properly?

    - by Jorge Castro
    I am in the process of building my first RAID5 array. I've used mdadm to create the following set up: root@bondigas:~# mdadm --detail /dev/md1 /dev/md1: Version : 00.90 Creation Time : Wed Oct 20 20:00:41 2010 Raid Level : raid5 Array Size : 5860543488 (5589.05 GiB 6001.20 GB) Used Dev Size : 1953514496 (1863.02 GiB 2000.40 GB) Raid Devices : 4 Total Devices : 4 Preferred Minor : 1 Persistence : Superblock is persistent Update Time : Wed Oct 20 20:13:48 2010 State : clean, degraded, recovering Active Devices : 3 Working Devices : 4 Failed Devices : 0 Spare Devices : 1 Layout : left-symmetric Chunk Size : 64K Rebuild Status : 1% complete UUID : f6dc829e:aa29b476:edd1ef19:85032322 (local to host bondigas) Events : 0.12 Number Major Minor RaidDevice State 0 8 16 0 active sync /dev/sdb 1 8 32 1 active sync /dev/sdc 2 8 48 2 active sync /dev/sdd 4 8 64 3 spare rebuilding /dev/sde While that's going I decided to format the beast with the following command: root@bondigas:~# mkfs.ext4 /dev/md1p1 mke2fs 1.41.11 (14-Mar-2010) /dev/md1p1 alignment is offset by 63488 bytes. This may result in very poor performance, (re)-partitioning suggested. Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=16 blocks, Stripe width=48 blocks 97853440 inodes, 391394047 blocks 19569702 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=0 11945 block groups 32768 blocks per group, 32768 fragments per group 8192 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208, 4096000, 7962624, 11239424, 20480000, 23887872, 71663616, 78675968, 102400000, 214990848 Writing inode tables: ^C 27/11945 root@bondigas:~# ^C I am unsure what to do about "/dev/md1p1 alignment is offset by 63488 bytes." and how to properly partition the disks to match so I can format it properly.

    Read the article

  • Cannot get temperatures in Dell Studio 1558

    - by Athul Iddya
    I could never get proper temperatures on my Dell Studio 1558. lm-sensors and acpi give wrong readings. The output of sensors is, $ sensors acpitz-virtual-0 Adapter: Virtual device temp1: +26.8°C (crit = +100.0°C) temp2: +0.0°C (crit = +100.0°C) acpi -V gives me, $ acpi -V Battery 0: Full, 100% Battery 0: design capacity 414 mAh, last full capacity 369 mAh = 89% Adapter 0: on-line Thermal 0: ok, 0.0 degrees C Thermal 0: trip point 0 switches to mode critical at temperature 100.0 degrees C Thermal 0: trip point 1 switches to mode passive at temperature 95.0 degrees C Thermal 0: trip point 2 switches to mode active at temperature 71.0 degrees C Thermal 0: trip point 3 switches to mode active at temperature 55.0 degrees C Thermal 1: ok, 26.8 degrees C Thermal 1: trip point 0 switches to mode critical at temperature 100.0 degrees C Thermal 1: trip point 1 switches to mode active at temperature 71.0 degrees C Thermal 1: trip point 2 switches to mode active at temperature 55.0 degrees C Cooling 0: LCD 0 of 15 Cooling 1: Processor 0 of 10 Cooling 2: Processor 0 of 10 Cooling 3: Processor 0 of 10 Cooling 4: Processor 0 of 10 Cooling 5: Fan 0 of 1 Cooling 6: Fan 0 of 1 I suspect even hddtemp gives bogus readings as its always at 46 $ sudo hddtemp /dev/sda /dev/sda: ST9500420AS: 46°C I have gone through some bug reports and some used to have the same problem after resuming from suspend. But I always have this problem. I had updated to the latest BIOS from Windows a couple of weeks ago, will updating from Ubuntu change anything? CORRECTION: hddtemp's readings do change. Its now at 45.

    Read the article

  • Notification framework for object lifecycle

    - by rlandster
    I am looking for an application, framework, or library that would help us with "object life-cycle management". There are many things that are created for users, departments, and services that, all too often, are left unmanaged. Some examples: user accounts groups SSL certificates access rights databases software license provisionings storage list-serve accounts These objects are created and managed by a wide variety of applications and systems. Typically, a user (person) requests (either explicitly or implicitly) one of these objects. A centralized management tool would help us manage such administration chores as: What objects does user X currently own/manage? Move the ownership of object P to user X; move all objects owned by user X (who was just been fired) to user Y. For all objects of type T that have expired be sure the objects have been disabled or deleted by their provider. How many active (expired, about-to-expire) objects of type P are there? Send periodic notifications to all users who own active objects of type P reminding them of what they own. There is a security alert for objects of type P; send a notification to all users who own these types of objects to take a specific remedial action. Delete or disable a set of objects based on expiration (or some other criteria). These objects are directly managed through their own applications (Active Directory, MySql, file systems, etc.) and may even have their own notification systems, but I want to centralize this into an "object management system". The OMS should allow the association with an external identity provider that defines who the users and groups are (e.g., LDAP, Active Directory) creation of objects association of an object to a specific user and/or group association with an expiration date creation of flexible reporting including letting users know what objects they currently own and their expiration dates integration with an external object "provider" via a plug-in We could write something from scratch, but I am hoping there is something already out there that will help, either an entire application or a set of libraries that provide much of what is needed. Any ideas?

    Read the article

  • Smooth drag scrolling of an Isometric map - Html5

    - by user881920
    I have implemented a basic Isometric tile engine that can be explored by dragging the map with the mouse. Please see the fiddle below and drag away: http://jsfiddle.net/kHydg/14/ The code broken down is (CoffeeScript): The draw function draw = -> requestAnimFrame draw canvas.width = canvas.width for row in [0..width] for col in [0..height] xpos = (row - col) * tileHeight + width xpos += (canvas.width / 2) - (tileWidth / 2) + scrollPosition.x ypos = (row + col) * (tileHeight / 2) + height + scrollPosition.y context.drawImage(defaultTile, Math.round(xpos), Math.round(ypos), tileWidth, tileHeight) Mouse drag-scrolling control scrollPosition = x: 0 y: 0 dragHelper = active: false x: 0 y: 0 window.addEventListener 'mousedown', (e) => handleMouseDown(e) , false window.addEventListener 'mousemove', (e) => handleDrag(e) , false window.addEventListener 'mouseup', (e) => handleMouseUp(e) , false handleDrag = (e) => e.preventDefault() if dragHelper.active x = e.clientX y = e.clientY scrollPosition.x -= Math.round((dragHelper.x - x) / 28) scrollPosition.y -= Math.round((dragHelper.y - y) / 28) handleMouseUp = (e) => e.preventDefault() dragHelper.active = false handleMouseDown = (e) => e.preventDefault() x = e.clientX y = e.clientY dragHelper.active = true dragHelper.x = x dragHelper.y = y The Problem As you can see from the fiddle the dragging action is ok but not perfect. How would I change the code to make the dragging action more smooth? What I would like is the point of the map you click on to stay under the mouse point whilst you drag; the same as they have done here: http://craftyjs.com/demos/isometric/

    Read the article

  • ????????????????????WebLogic Server 12c????

    - by ???02
    ??????Java EE 6???????????WebLogic Server 12c????????WebLogic Server 12c???/?????????????????????????????WebLogic Server 12c????????·??????·?????????????????????????/??????????????????????????????????(???) Web????????????????????Web?????·??????? WebLogic Server 12c???????????????????????????? Fusion Middleware?????? ????????? Cloud Application Foundation???????? ???????????????????? 24??365??????????????????IT?????????????????????????????????????????????????????????Oracle Real Application Cluster(RAC)???Oracle RAC?????????Oracle Database???????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????? ??Oracle RAC???????????????WebLogic Server????????????Active GridLink(GridLink??????)???Active GridLink?????????????????????????????WebLogic Server????????????Oracle RAC????????????Active GridLink ?Oracle RAC?????????????????????????????????????·?????????????XA?????????RAC??????·???????????????????? ??Active GridLink??WebLogic Server 12c?????????????Web??????RAC??????·??????(Web?????·??????)???? Oracle RAC?????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????????·???????????????????·?????????????? ???Web?????·?????????????????????????????HTTP?????????????????????????RAC???????????????????????????????????????????????????Oracle RAC??????????????????????????????????????????? ??Web?????·??????????????????????????????????????????????????????????????????????????????????????????????????????Web??????????????????????????????????????????????????????????Web?????·???????????????????????????? ????????·???????????????JDBC TLOG????????????? ???????WebLogic Server 12c?????????????????????????·??(TLOG)?Oracle Database??????JDBC TLOG???????? ????????????·???????????????????????????????????????????????2????·??????????????????????????????·?????????????????????????????????(????1)???????????·????????????????????????(????2)???????1??????????????????????????????????????????????????????????????????????????????TLOG??????????????????????????????????????????????? ???WebLogic Server?????TLOG?????·???????????????12c??Oracle Database?????????????????????????????????????·????JMS?????????TLOG????????????·????????????????????????????????????????? ??????????????????????????WebLogic Server???????????????????????????????????????????????TLOG?????·??????????????????????????????TLOG?????????????????????·??????????????????????????????????????????????????????????????????????????????????? Oracle Database???????????????????????????????????Oracle Data Guard?????????????????·????TLOG??????????????????????????????????????????????????????????????? ?????????·????????TLOG??????????·?????????????????????????????????????????????????????Oracle Data Guard?TLOG?????????????????????????????????????????????????????????TLOG??????????????????Oracle Data Guard?????????????? HTTP???????????????RESTful Management Services? ???????????????1????????????RESTful Management Services??????HTTP??????WebLogic Server 12c???????????????????????????????HTML?JSON?XML???????????? ????????TCP?80?????????????????????????????????????????????????PC???????????WebLogic Server????????????????????????????????????????????????????????????HTTP????????????????????????????????????????? ?????????????2??????WebLogic Server 12c??????????????????WebLogic Server 12c??Java EE 6/Java SE 7???????????????????????????????????????????????????????????????????

    Read the article

  • Detecting Idle Time with Global Mouse and Keyboard Hooks in WPF

    - by jdanforth
    Years and years ago I wrote this blog post about detecting if the user was idle or active at the keyboard (and mouse) using a global hook. Well that code was for .NET 2.0 and Windows Forms and for some reason I wanted to try the same in WPF and noticed that a few things around the keyboard and mouse hooks didn’t work as expected in the WPF environment. So I had to change a few things and here’s the code for it, working in .NET 4. I took the liberty and refactored a few things while at it and here’s the code now. I’m sure I will need it in the far future as well. using System; using System.Diagnostics; using System.Runtime.InteropServices; namespace Irm.Tim.Snapper.Util { public class ClientIdleHandler : IDisposable { public bool IsActive { get; set; } int _hHookKbd; int _hHookMouse; public delegate int HookProc(int nCode, IntPtr wParam, IntPtr lParam); public event HookProc MouseHookProcedure; public event HookProc KbdHookProcedure; //Use this function to install thread-specific hook. [DllImport("user32.dll", CharSet = CharSet.Auto, CallingConvention = CallingConvention.StdCall)] public static extern int SetWindowsHookEx(int idHook, HookProc lpfn, IntPtr hInstance, int threadId); //Call this function to uninstall the hook. [DllImport("user32.dll", CharSet = CharSet.Auto, CallingConvention = CallingConvention.StdCall)] public static extern bool UnhookWindowsHookEx(int idHook); //Use this function to pass the hook information to next hook procedure in chain. [DllImport("user32.dll", CharSet = CharSet.Auto, CallingConvention = CallingConvention.StdCall)] public static extern int CallNextHookEx(int idHook, int nCode, IntPtr wParam, IntPtr lParam); //Use this hook to get the module handle, needed for WPF environment [DllImport("kernel32.dll", CharSet = CharSet.Auto)] public static extern IntPtr GetModuleHandle(string lpModuleName); public enum HookType : int { GlobalKeyboard = 13, GlobalMouse = 14 } public int MouseHookProc(int nCode, IntPtr wParam, IntPtr lParam) { //user is active, at least with the mouse IsActive = true; Debug.Print("Mouse active"); //just return the next hook return CallNextHookEx(_hHookMouse, nCode, wParam, lParam); } public int KbdHookProc(int nCode, IntPtr wParam, IntPtr lParam) { //user is active, at least with the keyboard IsActive = true; Debug.Print("Keyboard active"); //just return the next hook return CallNextHookEx(_hHookKbd, nCode, wParam, lParam); } public void Start() { using (var currentProcess = Process.GetCurrentProcess()) using (var mainModule = currentProcess.MainModule) { if (_hHookMouse == 0) { // Create an instance of HookProc. MouseHookProcedure = new HookProc(MouseHookProc); // Create an instance of HookProc. KbdHookProcedure = new HookProc(KbdHookProc); //register a global hook _hHookMouse = SetWindowsHookEx((int)HookType.GlobalMouse, MouseHookProcedure, GetModuleHandle(mainModule.ModuleName), 0); if (_hHookMouse == 0) { Close(); throw new ApplicationException("SetWindowsHookEx() failed for the mouse"); } } if (_hHookKbd == 0) { //register a global hook _hHookKbd = SetWindowsHookEx((int)HookType.GlobalKeyboard, KbdHookProcedure, GetModuleHandle(mainModule.ModuleName), 0); if (_hHookKbd == 0) { Close(); throw new ApplicationException("SetWindowsHookEx() failed for the keyboard"); } } } } public void Close() { if (_hHookMouse != 0) { bool ret = UnhookWindowsHookEx(_hHookMouse); if (ret == false) { throw new ApplicationException("UnhookWindowsHookEx() failed for the mouse"); } _hHookMouse = 0; } if (_hHookKbd != 0) { bool ret = UnhookWindowsHookEx(_hHookKbd); if (ret == false) { throw new ApplicationException("UnhookWindowsHookEx() failed for the keyboard"); } _hHookKbd = 0; } } #region IDisposable Members public void Dispose() { if (_hHookMouse != 0 || _hHookKbd != 0) Close(); } #endregion } } The way you use it is quite simple, for example in a WPF application with a simple Window and a TextBlock: <Window x:Class="WpfApplication2.MainWindow" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" Title="MainWindow" Height="350" Width="525"> <Grid> <TextBlock Name="IdleTextBox"/> </Grid> </Window> And in the code behind we wire up the ClientIdleHandler and a DispatcherTimer that ticks every second: public partial class MainWindow : Window { private DispatcherTimer _dispatcherTimer; private ClientIdleHandler _clientIdleHandler; public MainWindow() { InitializeComponent(); } private void Window_Loaded(object sender, RoutedEventArgs e) { //start client idle hook _clientIdleHandler = new ClientIdleHandler(); _clientIdleHandler.Start(); //start timer _dispatcherTimer = new DispatcherTimer(); _dispatcherTimer.Tick += TimerTick; _dispatcherTimer.Interval = new TimeSpan(0, 0, 0, 1); _dispatcherTimer.Start(); } private void TimerTick(object sender, EventArgs e) { if (_clientIdleHandler.IsActive) { IdleTextBox.Text = "Active"; //reset IsActive flag _clientIdleHandler.IsActive = false; } else IdleTextBox.Text = "Idle"; } } Remember to reset the ClientIdleHandle IsActive flag after a check.

    Read the article

  • Sign on Experience with Office 365

    - by Sahil Malik
    SharePoint 2010 Training: more information Office 365 offers two types of identities: · Microsoft Online Services cloud IDs (Cloud Identity): This is the default identity Microsoft provides you, requires no additional setup, you sign up for Office 365 and you are provided a credential. You can sign in using forms based authentication, the password policy etc. for which is stored in the cloud with the Office 365 service. The advantage obviously is no additional setup headache. The disadvantage? Yet another password to remember, and no hope of authenticated single sign on integration using this cloud identity with other services at least in the current version. · Federated IDs (Federated Identity): In companies with on-premises Active Directory, users can sign into Office 365 services using their Active Directory credentials. The corporate Active Directory authenticates the users, and stores and controls the password policy. The advantage here is plenty of single sign on possibilities and better user experience. The downside, more Read full article ....

    Read the article

  • How to change web browser's tab bar background color or image?

    - by Hanynowsky
    Running Precise. I am tweaking the ambiance theme to my taste. Yet I can't locate where I can modify the background color of the browser's tab bar (I suspect its value instruction to be somewhere in the gtk-widget or gtk-3 style files). See image: Thanks in advance. -------------------EDIT----------------------- Solution: Edited the following files: /usr/share/themes/MyTheme/gtk-2.0/apps/chromium.rc ( style "chrome-gtk-frame"{ ...}) gtk.css gtkrc (gtk-2.0 folder / first line of style dark - background - ) : style "dark" { color["bg_color_dark"] = "#303030" #original was 3c3b37 color["fg_color_dark"] = "#dfdbd2" color["selected_fg_color_dark"] = "#ffffff" fg[NORMAL] = @fg_color_dark fg[PRELIGHT] = shade (1.15, @fg_color_dark) fg[ACTIVE] = @fg_color_dark fg[SELECTED] = @selected_fg_color_dark fg[INSENSITIVE] = shade (0.5, @fg_color_dark) bg[NORMAL] = @bg_color_dark bg[ACTIVE] = shade (0.8, @bg_color_dark) bg[SELECTED] = @selected_bg_color bg[PRELIGHT] = shade (1.0, "#4D4C48") bg[INSENSITIVE] = shade (0.85, @bg_color_dark) text[NORMAL] = @fg_color_dark text[PRELIGHT] = shade (1.15, @fg_color_dark) text[SELECTED] = @selected_fg_color_dark text[ACTIVE] = @fg_color_dark text[INSENSITIVE] = mix (0.5, @bg_color, @bg_color_dark) } RESULT:

    Read the article

  • Reading the tea leaves from Windows Azure support

    - by jamiet
    A few idle thoughts… Three months ago I had an issue regarding Windows Azure where I was unable to login to the management portal. At the time I contacted Azure support, the issue was soon resolved and I thought no more about it. Until today that is when I received an email from Azure support providing a detailed analysis of the root cause, the fix and moreover precise details about when and where things occurred. The email itself is interesting and I have included the entirety of it below. A few things were interesting to me: The level of detail and the diligence in investigating and reporting the issue I found really rather impressive. They even outline the number of users that were affected (127 in case you can’t be bothered reading). Compare this to the quite pathetic support that another division within Microsoft, Skype, provided to Greg Low recently: Skype support and dead parrot sketches   This line: “Windows Azure performed a planned change from using the Microsoft account service (formerly Windows Live ID) to the Azure Active Directory (AAD) as its primary authentication mechanism on August 24th. This change was made to enable future innovation in the area of authentication – particularly for organizationally owned identities, identity federation, stronger authentication methods and compliance certification. ” I also found to be particularly interesting. I have long thought that one of the reasons Microsoft has proved to be such a money-making machine in the enterprise is because they provide the infrastructure and then upsell on top of that – and nothing is more infrastructural than Active Directory. It has struck me of late that they are trying to make the same play of late in the cloud by tying all their services into Azure Active Directory and here we see a clear indication of that by making AAD the authentication mechanism for anyone using Windows Azure. I get the feeling that we’re going to hear much much more about AAD in the future; isn’t it about time we could log on to SQL Azure Windows Azure SQL Database without resorting to SQL authentication, for example? And why do Microsoft have two identity providers – Microsoft Account (aka Windows Live ID) and AAD – isn’t it about time those things were combined? As I said, just some idle thoughts. Below is the transcript of the email if you are interested. @Jamiet  This is regarding the support request <redacted> where in you were not able to login into the windows azure management portal with live id. We are providing you with the summary, root cause analysis and information about permanent fix: Incident Title: You were unable to access Windows Azure Portal after Microsoft Account to Azure Active Directory account Migration. Service Impacted: Management Portal Incident Start Date and Time: 8/24/2012 4:30:00 PM Date and Time Service was Restored: 10/17/2012 12:00:00 AM Summary: Windows Azure performed a planned change from using the Microsoft account service (formerly Windows Live ID) to the Azure Active Directory (AAD) as its primary authentication mechanism on August 24th.   This change was made to enable future innovation in the area of authentication – particularly for organizationally owned identities, identity federation, stronger authentication methods and compliance certification.   While this migration was largely transparent to Windows Azure users, a small number of users whose sign-in names were part of a Windows Live Custom Domain were unable to login.   This incompatibility was not discovered during the Quality Assurance testing phase prior to the migration. Customer Impact: Customers whose sign-in names were part of a Windows Live Custom Domain were unable to sign-in the Management Portal after ~4:00 p.m. PST on August 24th, 2012.   We determined that the issue did impact at least 127 users in 98 of these Windows Live Custom Domains and had a maximum potential impact of 1,110 users in total. Root Cause: The root cause of the issue was an incompatibility in the AAD authentication service to handle logins from Microsoft accounts whose sign-in names were part of a Windows Live Custom Domains.  This issue was not discovered during the Quality Assurance testing phase prior to the migration from Microsoft Account (MSA) to AAD. Mitigations: The issue was mitigated for the majority of affected users by 8:20 a.m. PST on August 25th, 2012 by running some internal scripts to correct many known Windows Live Custom Domains.   The remaining affected domains fell into two categories: Windows Live Custom Domains that were not corrected by 8/25/2012. An additional 48 Windows Live Custom Domains were fixed in the weeks following the incident within 2 business days after the AAD team received an escalation from product support regarding those accounts. Windows Live Custom domains that were also provisioned in Office365. Some of the affected Windows Live Custom Domains had already been provisioned in AAD because their owners signed up for Office365 which is a service that also uses AAD.   In these cases the Azure customers had to work around the issue by renaming their Microsoft Account or using a different Microsoft Account to administer their Azure subscription. Permanent Fix: The Azure Active Directory team permanently fixed the issue for all customers on 10/17/2012 in an upgraded release of the AAD service.

    Read the article

  • seo for complex url

    - by Mark
    I have a jobs website. There are categories and sub categories e.g the url for builders is www.mydomain.com/jobs/all/active/202/tradesmen/799/builders/county/all Because of the framework im using (Elgg), the "all" and "active" come after the plugin name. Also, i need to do a lot of things with the url: get the pplugin (job), get the correct type of entities (all and active), get the category (202 and tradesmen), get the subcategory (799 & builders) and get the location (county and all). Is this URL seo friendly or is it too messy? Is something like www.mydomain.com/jobs/tradesmen/builders/all better?

    Read the article

  • Added splash screen code to my package

    - by Youssef
    Please i need support to added splash screen code to my package /* * T24_Transformer_FormView.java */ package t24_transformer_form; import org.jdesktop.application.Action; import org.jdesktop.application.ResourceMap; import org.jdesktop.application.SingleFrameApplication; import org.jdesktop.application.FrameView; import org.jdesktop.application.TaskMonitor; import java.awt.event.ActionEvent; import java.awt.event.ActionListener; import javax.swing.filechooser.FileNameExtensionFilter; import javax.swing.filechooser.FileFilter; // old T24 Transformer imports import java.io.File; import java.io.FileWriter; import java.io.StringWriter; import java.text.SimpleDateFormat; import java.util.ArrayList; import java.util.Date; import java.util.HashMap; import java.util.Iterator; //import java.util.Properties; import java.util.StringTokenizer; import javax.swing.; import javax.xml.parsers.DocumentBuilder; import javax.xml.parsers.DocumentBuilderFactory; import javax.xml.transform.Result; import javax.xml.transform.Source; import javax.xml.transform.Transformer; import javax.xml.transform.TransformerFactory; import javax.xml.transform.dom.DOMSource; import javax.xml.transform.stream.StreamResult; import org.apache.log4j.Logger; import org.apache.log4j.PropertyConfigurator; import org.w3c.dom.Document; import org.w3c.dom.DocumentFragment; import org.w3c.dom.Element; import org.w3c.dom.Node; import org.w3c.dom.NodeList; import com.ejada.alinma.edh.xsdtransform.util.ConfigKeys; import com.ejada.alinma.edh.xsdtransform.util.XSDElement; import com.sun.org.apache.xml.internal.serialize.OutputFormat; import com.sun.org.apache.xml.internal.serialize.XMLSerializer; /* * The application's main frame. */ public class T24_Transformer_FormView extends FrameView { /**} * static holders for application-level utilities * { */ //private static Properties appProps; private static Logger appLogger; /** * */ private StringBuffer columnsCSV = null; private ArrayList<String> singleValueTableColumns = null; private HashMap<String, String> multiValueTablesSQL = null; private HashMap<Object, HashMap<String, Object>> groupAttrs = null; private ArrayList<XSDElement> xsdElementsList = null; /** * initialization */ private void init() /*throws Exception*/ { // init the properties object //FileReader in = new FileReader(appConfigPropsPath); //appProps.load(in); // log4j.properties constant String PROP_LOG4J_CONFIG_FILE = "log4j.properties"; // init the logger if ((PROP_LOG4J_CONFIG_FILE != null) && (!PROP_LOG4J_CONFIG_FILE.equals(""))) { PropertyConfigurator.configure(PROP_LOG4J_CONFIG_FILE); if (appLogger == null) { appLogger = Logger.getLogger(T24_Transformer_FormView.class.getName()); } appLogger.info("Application initialization successful."); } columnsCSV = new StringBuffer(ConfigKeys.FIELD_TAG + "," + ConfigKeys.FIELD_NUMBER + "," + ConfigKeys.FIELD_DATA_TYPE + "," + ConfigKeys.FIELD_FMT + "," + ConfigKeys.FIELD_LEN + "," + ConfigKeys.FIELD_INPUT_LEN + "," + ConfigKeys.FIELD_GROUP_NUMBER + "," + ConfigKeys.FIELD_MV_GROUP_NUMBER + "," + ConfigKeys.FIELD_SHORT_NAME + "," + ConfigKeys.FIELD_NAME + "," + ConfigKeys.FIELD_COLUMN_NAME + "," + ConfigKeys.FIELD_GROUP_NAME + "," + ConfigKeys.FIELD_MV_GROUP_NAME + "," + ConfigKeys.FIELD_JUSTIFICATION + "," + ConfigKeys.FIELD_TYPE + "," + ConfigKeys.FIELD_SINGLE_OR_MULTI + System.getProperty("line.separator")); singleValueTableColumns = new ArrayList<String>(); singleValueTableColumns.add(ConfigKeys.COLUMN_XPK_ROW + ConfigKeys.DELIMITER_COLUMN_TYPE + ConfigKeys.DATA_TYPE_XSD_NUMERIC); multiValueTablesSQL = new HashMap<String, String>(); groupAttrs = new HashMap<Object, HashMap<String, Object>>(); xsdElementsList = new ArrayList<XSDElement>(); } /** * initialize the <code>DocumentBuilder</code> and read the XSD file * * @param docPath * @return the <code>Document</code> object representing the read XSD file */ private Document retrieveDoc(String docPath) { Document xsdDoc = null; File file = new File(docPath); try { DocumentBuilder builder = DocumentBuilderFactory.newInstance().newDocumentBuilder(); xsdDoc = builder.parse(file); } catch (Exception e) { appLogger.error(e.getMessage()); } return xsdDoc; } /** * perform the iteration/modification on the document * iterate to the level which contains all the elements (Single-Value, and Groups) and start processing each * * @param xsdDoc * @return */ private Document processDoc(Document xsdDoc) { ArrayList<Object> newElementsList = new ArrayList<Object>(); HashMap<String, Object> docAttrMap = new HashMap<String, Object>(); Element sequenceElement = null; Element schemaElement = null; // get document's root element NodeList nodes = xsdDoc.getChildNodes(); for (int i = 0; i < nodes.getLength(); i++) { if (ConfigKeys.TAG_SCHEMA.equals(nodes.item(i).getNodeName())) { schemaElement = (Element) nodes.item(i); break; } } // process the document (change single-value elements, collect list of new elements to be added) for (int i1 = 0; i1 < schemaElement.getChildNodes().getLength(); i1++) { Node childLevel1 = (Node) schemaElement.getChildNodes().item(i1); // <ComplexType> element if (childLevel1.getNodeName().equals(ConfigKeys.TAG_COMPLEX_TYPE)) { // first, get the main attributes and put it in the csv file for (int i6 = 0; i6 < childLevel1.getChildNodes().getLength(); i6++) { Node child6 = childLevel1.getChildNodes().item(i6); if (ConfigKeys.TAG_ATTRIBUTE.equals(child6.getNodeName())) { if (child6.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME) != null) { String attrName = child6.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME).getNodeValue(); if (((Element) child6).getElementsByTagName(ConfigKeys.TAG_SIMPLE_TYPE).getLength() != 0) { Node simpleTypeElement = ((Element) child6).getElementsByTagName(ConfigKeys.TAG_SIMPLE_TYPE) .item(0); if (((Element) simpleTypeElement).getElementsByTagName(ConfigKeys.TAG_RESTRICTION).getLength() != 0) { Node restrictionElement = ((Element) simpleTypeElement).getElementsByTagName( ConfigKeys.TAG_RESTRICTION).item(0); if (((Element) restrictionElement).getElementsByTagName(ConfigKeys.TAG_MAX_LENGTH).getLength() != 0) { Node maxLengthElement = ((Element) restrictionElement).getElementsByTagName( ConfigKeys.TAG_MAX_LENGTH).item(0); HashMap<String, String> elementProperties = new HashMap<String, String>(); elementProperties.put(ConfigKeys.FIELD_TAG, attrName); elementProperties.put(ConfigKeys.FIELD_NUMBER, "0"); elementProperties.put(ConfigKeys.FIELD_DATA_TYPE, ConfigKeys.DATA_TYPE_XSD_STRING); elementProperties.put(ConfigKeys.FIELD_FMT, ""); elementProperties.put(ConfigKeys.FIELD_NAME, attrName); elementProperties.put(ConfigKeys.FIELD_SHORT_NAME, attrName); elementProperties.put(ConfigKeys.FIELD_COLUMN_NAME, attrName); elementProperties.put(ConfigKeys.FIELD_SINGLE_OR_MULTI, "S"); elementProperties.put(ConfigKeys.FIELD_LEN, maxLengthElement.getAttributes().getNamedItem( ConfigKeys.ATTR_VALUE).getNodeValue()); elementProperties.put(ConfigKeys.FIELD_INPUT_LEN, maxLengthElement.getAttributes() .getNamedItem(ConfigKeys.ATTR_VALUE).getNodeValue()); constructElementRow(elementProperties); // add the attribute as a column in the single-value table singleValueTableColumns.add(attrName + ConfigKeys.DELIMITER_COLUMN_TYPE + ConfigKeys.DATA_TYPE_XSD_STRING + ConfigKeys.DELIMITER_COLUMN_TYPE + maxLengthElement.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE).getNodeValue()); // add the attribute as an element in the elements list addToElementsList(attrName, attrName); appLogger.debug("added attribute: " + attrName); } } } } } } // now, loop on the elements and process them for (int i2 = 0; i2 < childLevel1.getChildNodes().getLength(); i2++) { Node childLevel2 = (Node) childLevel1.getChildNodes().item(i2); // <Sequence> element if (childLevel2.getNodeName().equals(ConfigKeys.TAG_SEQUENCE)) { sequenceElement = (Element) childLevel2; for (int i3 = 0; i3 < childLevel2.getChildNodes().getLength(); i3++) { Node childLevel3 = (Node) childLevel2.getChildNodes().item(i3); // <Element> element if (childLevel3.getNodeName().equals(ConfigKeys.TAG_ELEMENT)) { // check if single element or group if (isGroup(childLevel3)) { processGroup(childLevel3, true, null, null, docAttrMap, xsdDoc, newElementsList); // insert a new comment node with the contents of the group tag sequenceElement.insertBefore(xsdDoc.createComment(serialize(childLevel3)), childLevel3); // remove the group tag sequenceElement.removeChild(childLevel3); } else { processElement(childLevel3); } } } } } } } // add new elements // this step should be after finishing processing the whole document. when you add new elements to the document // while you are working on it, those new elements will be included in the processing. We don't need that! for (int i = 0; i < newElementsList.size(); i++) { sequenceElement.appendChild((Element) newElementsList.get(i)); } // write the new required attributes to the schema element Iterator<String> attrIter = docAttrMap.keySet().iterator(); while(attrIter.hasNext()) { Element attr = (Element) docAttrMap.get(attrIter.next()); Element newAttrElement = xsdDoc.createElement(ConfigKeys.TAG_ATTRIBUTE); appLogger.debug("appending attr. [" + attr.getAttribute(ConfigKeys.ATTR_NAME) + "]..."); newAttrElement.setAttribute(ConfigKeys.ATTR_NAME, attr.getAttribute(ConfigKeys.ATTR_NAME)); newAttrElement.setAttribute(ConfigKeys.ATTR_TYPE, attr.getAttribute(ConfigKeys.ATTR_TYPE)); schemaElement.appendChild(newAttrElement); } return xsdDoc; } /** * add a new <code>XSDElement</code> with the given <code>name</code> and <code>businessName</code> to * the elements list * * @param name * @param businessName */ private void addToElementsList(String name, String businessName) { xsdElementsList.add(new XSDElement(name, businessName)); } /** * add the given <code>XSDElement</code> to the elements list * * @param element */ private void addToElementsList(XSDElement element) { xsdElementsList.add(element); } /** * check if the <code>element</code> sent is single-value element or group * element. the comparison depends on the children of the element. if found one of type * <code>ComplexType</code> then it's a group element, and if of type * <code>SimpleType</code> then it's a single-value element * * @param element * @return <code>true</code> if the element is a group element, * <code>false</code> otherwise */ private boolean isGroup(Node element) { for (int i = 0; i < element.getChildNodes().getLength(); i++) { Node child = (Node) element.getChildNodes().item(i); if (child.getNodeName().equals(ConfigKeys.TAG_COMPLEX_TYPE)) { // found a ComplexType child (Group element) return true; } else if (child.getNodeName().equals(ConfigKeys.TAG_SIMPLE_TYPE)) { // found a SimpleType child (Single-Value element) return false; } } return false; /* String attrName = null; if (element.getAttributes() != null) { Node attribute = element.getAttributes().getNamedItem(XSDTransformer.ATTR_NAME); if (attribute != null) { attrName = attribute.getNodeValue(); } } if (attrName.startsWith("g")) { // group element return true; } else { // single element return false; } */ } /** * process a group element. recursively, process groups till no more group elements are found * * @param element * @param isFirstLevelGroup * @param attrMap * @param docAttrMap * @param xsdDoc * @param newElementsList */ private void processGroup(Node element, boolean isFirstLevelGroup, Node parentGroup, XSDElement parentGroupElement, HashMap<String, Object> docAttrMap, Document xsdDoc, ArrayList<Object> newElementsList) { String elementName = null; HashMap<String, Object> groupAttrMap = new HashMap<String, Object>(); HashMap<String, Object> parentGroupAttrMap = new HashMap<String, Object>(); XSDElement groupElement = null; if (element.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME) != null) { elementName = element.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME).getNodeValue(); } appLogger.debug("processing group [" + elementName + "]..."); groupElement = new XSDElement(elementName, elementName); // get the attributes if a non-first-level-group // attributes are: groups's own attributes + parent group's attributes if (!isFirstLevelGroup) { // get the current element (group) attributes for (int i1 = 0; i1 < element.getChildNodes().getLength(); i1++) { if (ConfigKeys.TAG_COMPLEX_TYPE.equals(element.getChildNodes().item(i1).getNodeName())) { Node complexTypeNode = element.getChildNodes().item(i1); for (int i2 = 0; i2 < complexTypeNode.getChildNodes().getLength(); i2++) { if (ConfigKeys.TAG_ATTRIBUTE.equals(complexTypeNode.getChildNodes().item(i2).getNodeName())) { appLogger.debug("add group attr: " + ((Element) complexTypeNode.getChildNodes().item(i2)).getAttribute(ConfigKeys.ATTR_NAME)); groupAttrMap.put(((Element) complexTypeNode.getChildNodes().item(i2)).getAttribute(ConfigKeys.ATTR_NAME), complexTypeNode.getChildNodes().item(i2)); docAttrMap.put(((Element) complexTypeNode.getChildNodes().item(i2)).getAttribute(ConfigKeys.ATTR_NAME), complexTypeNode.getChildNodes().item(i2)); } } } } // now, get the parent's attributes parentGroupAttrMap = groupAttrs.get(parentGroup); if (parentGroupAttrMap != null) { Iterator<String> iter = parentGroupAttrMap.keySet().iterator(); while (iter.hasNext()) { String attrName = iter.next(); groupAttrMap.put(attrName, parentGroupAttrMap.get(attrName)); } } // add the attributes to the group element that will be added to the elements list Iterator<String> itr = groupAttrMap.keySet().iterator(); while(itr.hasNext()) { groupElement.addAttribute(itr.next()); } // put the attributes in the attributes map groupAttrs.put(element, groupAttrMap); } for (int i = 0; i < element.getChildNodes().getLength(); i++) { Node childLevel1 = (Node) element.getChildNodes().item(i); if (childLevel1.getNodeName().equals(ConfigKeys.TAG_COMPLEX_TYPE)) { for (int j = 0; j < childLevel1.getChildNodes().getLength(); j++) { Node childLevel2 = (Node) childLevel1.getChildNodes().item(j); if (childLevel2.getNodeName().equals(ConfigKeys.TAG_SEQUENCE)) { for (int k = 0; k < childLevel2.getChildNodes().getLength(); k++) { Node childLevel3 = (Node) childLevel2.getChildNodes().item(k); if (childLevel3.getNodeName().equals(ConfigKeys.TAG_ELEMENT)) { // check if single element or group if (isGroup(childLevel3)) { // another group element.. // unfortunately, a recursion is // needed here!!! :-( processGroup(childLevel3, false, element, groupElement, docAttrMap, xsdDoc, newElementsList); } else { // reached a single-value element.. copy it under the // main sequence and apply the name<>shorname replacement processGroupElement(childLevel3, element, groupElement, isFirstLevelGroup, xsdDoc, newElementsList); } } } } } } } if (isFirstLevelGroup) { addToElementsList(groupElement); } else { parentGroupElement.addChild(groupElement); } appLogger.debug("finished processing group [" + elementName + "]."); } /** * process the sent <code>element</code> to extract/modify required * information: * 1. replace the <code>name</code> attribute with the <code>shortname</code>. * * @param element */ private void processElement(Node element) { String fieldShortName = null; String fieldColumnName = null; String fieldDataType = null; String fieldFormat = null; String fieldInputLength = null; String elementName = null; HashMap<String, String> elementProperties = new HashMap<String, String>(); if (element.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME) != null) { elementName = element.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME).getNodeValue(); } appLogger.debug("processing element [" + elementName + "]..."); for (int i = 0; i < element.getChildNodes().getLength(); i++) { Node childLevel1 = (Node) element.getChildNodes().item(i); if (childLevel1.getNodeName().equals(ConfigKeys.TAG_ANNOTATION)) { for (int j = 0; j < childLevel1.getChildNodes().getLength(); j++) { Node childLevel2 = (Node) childLevel1.getChildNodes().item(j); if (childLevel2.getNodeName().equals(ConfigKeys.TAG_APP_INFO)) { for (int k = 0; k < childLevel2.getChildNodes().getLength(); k++) { Node childLevel3 = (Node) childLevel2.getChildNodes().item(k); if (childLevel3.getNodeName().equals(ConfigKeys.TAG_HAS_PROPERTY)) { if (childLevel3.getAttributes() != null) { String attrName = null; Node attribute = childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME); if (attribute != null) { attrName = attribute.getNodeValue(); elementProperties.put(attrName, childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE) .getNodeValue()); if (attrName.equals(ConfigKeys.FIELD_SHORT_NAME)) { fieldShortName = childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE) .getNodeValue(); } else if (attrName.equals(ConfigKeys.FIELD_COLUMN_NAME)) { fieldColumnName = childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE) .getNodeValue(); } else if (attrName.equals(ConfigKeys.FIELD_DATA_TYPE)) { fieldDataType = childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE) .getNodeValue(); } else if (attrName.equals(ConfigKeys.FIELD_FMT)) { fieldFormat = childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE) .getNodeValue(); } else if (attrName.equals(ConfigKeys.FIELD_INPUT_LEN)) { fieldInputLength = childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE) .getNodeValue(); } } } } } } } } } // replace the name attribute with the shortname if (element.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME) != null) { element.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME).setNodeValue(fieldShortName); } elementProperties.put(ConfigKeys.FIELD_SINGLE_OR_MULTI, "S"); constructElementRow(elementProperties); singleValueTableColumns.add(fieldShortName + ConfigKeys.DELIMITER_COLUMN_TYPE + fieldDataType + fieldFormat + ConfigKeys.DELIMITER_COLUMN_TYPE + fieldInputLength); // add the element to elements list addToElementsList(fieldShortName, fieldColumnName); appLogger.debug("finished processing element [" + elementName + "]."); } /** * process the sent <code>element</code> to extract/modify required * information: * 1. copy the element under the main sequence * 2. replace the <code>name</code> attribute with the <code>shortname</code>. * 3. add the attributes of the parent groups (if non-first-level-group) * * @param element */ private void processGroupElement(Node element, Node parentGroup, XSDElement parentGroupElement, boolean isFirstLevelGroup, Document xsdDoc, ArrayList<Object> newElementsList) { String fieldShortName = null; String fieldColumnName = null; String fieldDataType = null; String fieldFormat = null; String fieldInputLength = null; String elementName = null; Element newElement = null; HashMap<String, String> elementProperties = new HashMap<String, String>(); ArrayList<String> tableColumns = new ArrayList<String>(); HashMap<String, Object> groupAttrMap = null; if (element.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME) != null) { elementName = element.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME).getNodeValue(); } appLogger.debug("processing element [" + elementName + "]..."); // 1. copy the element newElement = (Element) element.cloneNode(true); newElement.setAttribute(ConfigKeys.ATTR_MAX_OCCURS, "unbounded"); // 2. if non-first-level-group, replace the element's SimpleType tag with a ComplexType tag if (!isFirstLevelGroup) { if (((Element) newElement).getElementsByTagName(ConfigKeys.TAG_SIMPLE_TYPE).getLength() != 0) { // there should be only one tag of SimpleType Node simpleTypeNode = ((Element) newElement).getElementsByTagName(ConfigKeys.TAG_SIMPLE_TYPE).item(0); // create the new ComplexType element Element complexTypeNode = xsdDoc.createElement(ConfigKeys.TAG_COMPLEX_TYPE); complexTypeNode.setAttribute(ConfigKeys.ATTR_MIXED, "true"); // get the list of attributes for the parent group groupAttrMap = groupAttrs.get(parentGroup); Iterator<String> attrIter = groupAttrMap.keySet().iterator(); while(attrIter.hasNext()) { Element attr = (Element) groupAttrMap.get(attrIter.next()); Element newAttrElement = xsdDoc.createElement(ConfigKeys.TAG_ATTRIBUTE); appLogger.debug("adding attr. [" + attr.getAttribute(ConfigKeys.ATTR_NAME) + "]..."); newAttrElement.setAttribute(ConfigKeys.ATTR_REF, attr.getAttribute(ConfigKeys.ATTR_NAME)); newAttrElement.setAttribute(ConfigKeys.ATTR_USE, "optional"); complexTypeNode.appendChild(newAttrElement); } // replace the old SimpleType node with the new ComplexType node newElement.replaceChild(complexTypeNode, simpleTypeNode); } } // 3. replace the name with the shortname in the new element for (int i = 0; i < newElement.getChildNodes().getLength(); i++) { Node childLevel1 = (Node) newElement.getChildNodes().item(i); if (childLevel1.getNodeName().equals(ConfigKeys.TAG_ANNOTATION)) { for (int j = 0; j < childLevel1.getChildNodes().getLength(); j++) { Node childLevel2 = (Node) childLevel1.getChildNodes().item(j); if (childLevel2.getNodeName().equals(ConfigKeys.TAG_APP_INFO)) { for (int k = 0; k < childLevel2.getChildNodes().getLength(); k++) { Node childLevel3 = (Node) childLevel2.getChildNodes().item(k); if (childLevel3.getNodeName().equals(ConfigKeys.TAG_HAS_PROPERTY)) { if (childLevel3.getAttributes() != null) { String attrName = null; Node attribute = childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME); if (attribute != null) { attrName = attribute.getNodeValue(); elementProperties.put(attrName, childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE) .getNodeValue()); if (attrName.equals(ConfigKeys.FIELD_SHORT_NAME)) { fieldShortName = childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE) .getNodeValue(); } else if (attrName.equals(ConfigKeys.FIELD_COLUMN_NAME)) { fieldColumnName = childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE) .getNodeValue(); } else if (attrName.equals(ConfigKeys.FIELD_DATA_TYPE)) { fieldDataType = childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE) .getNodeValue(); } else if (attrName.equals(ConfigKeys.FIELD_FMT)) { fieldFormat = childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE) .getNodeValue(); } else if (attrName.equals(ConfigKeys.FIELD_INPUT_LEN)) { fieldInputLength = childLevel3.getAttributes().getNamedItem(ConfigKeys.ATTR_VALUE) .getNodeValue(); } } } } } } } } } if (newElement.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME) != null) { newElement.getAttributes().getNamedItem(ConfigKeys.ATTR_NAME).setNodeValue(fieldShortName); } // 4. save the new element to be added to the sequence list newElementsList.add(newElement); elementProperties.put(ConfigKeys.FIELD_SINGLE_OR_MULTI, "M"); constructElementRow(elementProperties); // create the MULTI-VALUE table // 0. Primary Key tableColumns.add(ConfigKeys.COLUMN_XPK_ROW + ConfigKeys.DELIMITER_COLUMN_TYPE + ConfigKeys.DATA_TYPE_XSD_STRING + ConfigKeys.DELIMITER_COLUMN_TYPE + ConfigKeys.COLUMN_XPK_ROW_LENGTH); // 1. foreign key tableColumns.add(ConfigKeys.COLUMN_FK_ROW + ConfigKeys.DELIMITER_COLUMN_TYPE + ConfigKeys.DATA_TYPE_XSD_NUMERIC); // 2. field value tableColumns.add(fieldShortName + ConfigKeys.DELIMITER_COLUMN_TYPE + fieldDataType + fieldFormat + ConfigKeys.DELIMITER_COLUMN_TYPE + fieldInputLength); // 3. attributes if (groupAttrMap != null) { Iterator<String> attrIter = groupAttrMap.keySet().iterator(); while (attrIter.hasNext()) { Element attr = (Element) groupAttrMap.get(attrIter.next()); tableColumns.add(attr.getAttribute(ConfigKeys.ATTR_NAME) + ConfigKeys.DELIMITER_COLUMN_TYPE + ConfigKeys.DATA_TYPE_XSD_NUMERIC); } } multiValueTablesSQL.put(sub_table_prefix.getText() + fieldShortName, constructMultiValueTableSQL( sub_table_prefix.getText() + fieldShortName, tableColumns)); // add the element to it's parent group children parentGroupElement.addChild(new XSDElement(fieldShortName, fieldColumnName)); appLogger.debug("finished processing element [" + elementName + "]."); } /** * write resulted files * * @param xsdDoc * @param docPath */ private void writeResults(Document xsdDoc, String resultsDir, String newXSDFileName, String csvFileName) { String rsDir = resultsDir + File.separator + new SimpleDateFormat("yyyyMMdd-HHmm").format(new Date()); try { File resultsDirFile = new File(rsDir); if (!resultsDirFile.exists()) { resultsDirFile.mkdirs(); } // write the XSD doc appLogger.info("writing the transformed XSD..."); Source source = new DOMSource(xsdDoc); Result result = new StreamResult(rsDir + File.separator + newXSDFileName); Transformer xformer = TransformerFactory.newInstance().newTransformer(); // xformer.setOutputProperty("indent", "yes"); xformer.transform(source, result); appLogger.info("finished writing the transformed XSD."); // write the CSV columns file appLogger.info("writing the CSV file..."); FileWriter csvWriter = new FileWriter(rsDir + File.separator + csvFileName); csvWriter.write(columnsCSV.toString()); csvWriter.close(); appLogger.info("finished writing the CSV file."); // write the master single-value table appLogger.info("writing the creation script for master table (single-values)..."); FileWriter masterTableWriter = new FileWriter(rsDir + File.separator + main_edh_table_name.getText() + ".sql"); masterTableWriter.write(constructSingleValueTableSQL(main_edh_table_name.getText(), singleValueTableColumns)); masterTableWriter.close(); appLogger.info("finished writing the creation script for master table (single-values)."); // write the multi-value tables sql appLogger.info("writing the creation script for slave tables (multi-values)..."); Iterator<String> iter = multiValueTablesSQL.keySet().iterator(); while (iter.hasNext()) { String tableName = iter.next(); String sql = multiValueTablesSQL.get(tableName); FileWriter tableSQLWriter = new FileWriter(rsDir + File.separator + tableName + ".sql"); tableSQLWriter.write(sql); tableSQLWriter.close(); } appLogger.info("finished writing the creation script for slave tables (multi-values)."); // write the single-value view appLogger.info("writing the creation script for single-value selection view..."); FileWriter singleValueViewWriter = new FileWriter(rsDir + File.separator + view_name_single.getText() + ".sql"); singleValueViewWriter.write(constructViewSQL(ConfigKeys.SQL_VIEW_SINGLE)); singleValueViewWriter.close(); appLogger.info("finished writing the creation script for single-value selection view."); // debug for (int i = 0; i < xsdElementsList.size(); i++) { getMultiView(xsdElementsList.get(i)); /*// if (xsdElementsList.get(i).getAllDescendants() != null) { // for (int j = 0; j < xsdElementsList.get(i).getAllDescendants().size(); j++) { // appLogger.debug(main_edh_table_name.getText() + "." + ConfigKeys.COLUMN_XPK_ROW // + "=" + xsdElementsList.get(i).getAllDescendants().get(j).getName() + "." + ConfigKeys.COLUMN_FK_ROW); // } // } */ } } catch (Exception e) { appLogger.error(e.getMessage()); } } private String getMultiView(XSDElement element)

    Read the article

  • How to get the permissions right for /dev/raw1394

    - by Mark0978
    I recently upgraded one of my ubuntu machines to Karmic and I'm having trouble getting the permissions of /dev/raw1394 set to 0666. They only thing this machine is used for is recording audio from a firepod which uses /dev/raw1394 via jackd and there are no other FireWire devices connected, so security around this device is not really an issue. If I run as root, everything works as expected, but I have some folks that run the recorder that I don't want to have root access. However, I can't figure out which lines setup the perms I've tied this: /etc/udev/permissions.d/raw1394.rules:raw1394:root:root:0666 And I have this setup (default install) /lib/udev/rules.d/75-persistent-net-generator.rules:SUBSYSTEMS=="ieee1394", ENV{COMMENT}="Firewire device $attr{host_id})" /lib/udev/rules.d/75-cd-aliases-generator.rules:# the "path" of usb/ieee1394 devices changes frequently, use "id" /lib/udev/rules.d/75-cd-aliases-generator.rules:ACTION=="add", SUBSYSTEM=="block", SUBSYSTEMS=="usb|ieee1394", ENV{ID_CDROM}=="?*", ENV{GENERATED}!="?*", \ /lib/udev/rules.d/60-persistent-storage-tape.rules:KERNEL=="st*[0-9]|nst*[0-9]", ATTRS{ieee1394_id}=="?*", ENV{ID_SERIAL}="$attr{ieee1394_id}", ENV{ID_BUS}="ieee1394" /lib/udev/rules.d/50-udev-default.rules:# FireWire (deprecated dv1394 and video1394 drivers) /lib/udev/rules.d/50-udev-default.rules:KERNEL=="dv1394-[0-9]*", NAME="dv1394/%n", GROUP="video" /lib/udev/rules.d/50-udev-default.rules:KERNEL=="video1394-[0-9]*", NAME="video1394/%n", GROUP="video" /lib/udev/rules.d/60-persistent-storage.rules:KERNEL=="sd*[!0-9]|sr*", ATTRS{ieee1394_id}=="?*", SYMLINK+="disk/by-id/ieee1394-$attr{ieee1394_id}" /lib/udev/rules.d/60-persistent-storage.rules:KERNEL=="sd*[0-9]", ATTRS{ieee1394_id}=="?*", SYMLINK+="disk/by-id/ieee1394-$attr{ieee1394_id}-part%n" And I find these lines in /var/log/syslog Apr 30 09:11:30 record kernel: [ 3.284010] ieee1394: Node added: ID:BUS[0-00:1023] GUID[000a9200c7062266] Apr 30 09:11:30 record kernel: [ 3.284195] ieee1394: Host added: ID:BUS[0-01:1023] GUID[00d0035600a97b9f] Apr 30 09:11:30 record kernel: [ 18.372791] ieee1394: raw1394: /dev/raw1394 device initialized What I can't figure out, is which line actually creates that raw1394 device in the first place. How do you get /dev/raw1394 to have permissions 0666?

    Read the article

  • .NET HTML Sanitation for rich HTML Input

    - by Rick Strahl
    Recently I was working on updating a legacy application to MVC 4 that included free form text input. When I set up the new site my initial approach was to not allow any rich HTML input, only simple text formatting that would respect a few simple HTML commands for bold, lists etc. and automatically handles line break processing for new lines and paragraphs. This is typical for what I do with most multi-line text input in my apps and it works very well with very little development effort involved. Then the client sprung another note: Oh by the way we have a bunch of customers (real estate agents) who need to post complete HTML documents. Oh uh! There goes the simple theory. After some discussion and pleading on my part (<snicker>) to try and avoid this type of raw HTML input because of potential XSS issues, the client decided to go ahead and allow raw HTML input anyway. There has been lots of discussions on this subject on StackOverFlow (and here and here) but to after reading through some of the solutions I didn't really find anything that would work even closely for what I needed. Specifically we need to be able to allow just about any HTML markup, with the exception of script code. Remote CSS and Images need to be loaded, links need to work and so. While the 'legit' HTML posted by these agents is basic in nature it does span most of the full gamut of HTML (4). Most of the solutions XSS prevention/sanitizer solutions I found were way to aggressive and rendered the posted output unusable mostly because they tend to strip any externally loaded content. In short I needed a custom solution. I thought the best solution to this would be to use an HTML parser - in this case the Html Agility Pack - and then to run through all the HTML markup provided and remove any of the blacklisted tags and a number of attributes that are prone to JavaScript injection. There's much discussion on whether to use blacklists vs. whitelists in the discussions mentioned above, but I found that whitelists can make sense in simple scenarios where you might allow manual HTML input, but when you need to allow a larger array of HTML functionality a blacklist is probably easier to manage as the vast majority of elements and attributes could be allowed. Also white listing gets a bit more complex with HTML5 and the new proliferation of new HTML tags and most new tags generally don't affect XSS issues directly. Pure whitelisting based on elements and attributes also doesn't capture many edge cases (see some of the XSS cheat sheets listed below) so even with a white list, custom logic is still required to handle many of those edge cases. The Microsoft Web Protection Library (AntiXSS) My first thought was to check out the Microsoft AntiXSS library. Microsoft has an HTML Encoding and Sanitation library in the Microsoft Web Protection Library (formerly AntiXSS Library) on CodePlex, which provides stricter functions for whitelist encoding and sanitation. Initially I thought the Sanitation class and its static members would do the trick for me,but I found that this library is way too restrictive for my needs. Specifically the Sanitation class strips out images and links which rendered the full HTML from our real estate clients completely useless. I didn't spend much time with it, but apparently I'm not alone if feeling this library is not really useful without some way to configure operation. To give you an example of what didn't work for me with the library here's a small and simple HTML fragment that includes script, img and anchor tags. I would expect the script to be stripped and everything else to be left intact. Here's the original HTML:var value = "<b>Here</b> <script>alert('hello')</script> we go. Visit the " + "<a href='http://west-wind.com'>West Wind</a> site. " + "<img src='http://west-wind.com/images/new.gif' /> " ; and the code to sanitize it with the AntiXSS Sanitize class:@Html.Raw(Microsoft.Security.Application.Sanitizer.GetSafeHtmlFragment(value)) This produced a not so useful sanitized string: Here we go. Visit the <a>West Wind</a> site. While it removed the <script> tag (good) it also removed the href from the link and the image tag altogether (bad). In some situations this might be useful, but for most tasks I doubt this is the desired behavior. While links can contain javascript: references and images can 'broadcast' information to a server, without configuration to tell the library what to restrict this becomes useless to me. I couldn't find any way to customize the white list, nor is there code available in this 'open source' library on CodePlex. Using Html Agility Pack for HTML Parsing The WPL library wasn't going to cut it. After doing a bit of research I decided the best approach for a custom solution would be to use an HTML parser and inspect the HTML fragment/document I'm trying to import. I've used the HTML Agility Pack before for a number of apps where I needed an HTML parser without requiring an instance of a full browser like the Internet Explorer Application object which is inadequate in Web apps. In case you haven't checked out the Html Agility Pack before, it's a powerful HTML parser library that you can use from your .NET code. It provides a simple, parsable HTML DOM model to full HTML documents or HTML fragments that let you walk through each of the elements in your document. If you've used the HTML or XML DOM in a browser before you'll feel right at home with the Agility Pack. Blacklist based HTML Parsing to strip XSS Code For my purposes of HTML sanitation, the process involved is to walk the HTML document one element at a time and then check each element and attribute against a blacklist. There's quite a bit of argument of what's better: A whitelist of allowed items or a blacklist of denied items. While whitelists tend to be more secure, they also require a lot more configuration. In the case of HTML5 a whitelist could be very extensive. For what I need, I only want to ensure that no JavaScript is executed, so a blacklist includes the obvious <script> tag plus any tag that allows loading of external content including <iframe>, <object>, <embed> and <link> etc. <form>  is also excluded to avoid posting content to a different location. I also disallow <head> and <meta> tags in particular for my case, since I'm only allowing posting of HTML fragments. There is also some internal logic to exclude some attributes or attributes that include references to JavaScript or CSS expressions. The default tag blacklist reflects my use case, but is customizable and can be added to. Here's my HtmlSanitizer implementation:using System.Collections.Generic; using System.IO; using System.Xml; using HtmlAgilityPack; namespace Westwind.Web.Utilities { public class HtmlSanitizer { public HashSet<string> BlackList = new HashSet<string>() { { "script" }, { "iframe" }, { "form" }, { "object" }, { "embed" }, { "link" }, { "head" }, { "meta" } }; /// <summary> /// Cleans up an HTML string and removes HTML tags in blacklist /// </summary> /// <param name="html"></param> /// <returns></returns> public static string SanitizeHtml(string html, params string[] blackList) { var sanitizer = new HtmlSanitizer(); if (blackList != null && blackList.Length > 0) { sanitizer.BlackList.Clear(); foreach (string item in blackList) sanitizer.BlackList.Add(item); } return sanitizer.Sanitize(html); } /// <summary> /// Cleans up an HTML string by removing elements /// on the blacklist and all elements that start /// with onXXX . /// </summary> /// <param name="html"></param> /// <returns></returns> public string Sanitize(string html) { var doc = new HtmlDocument(); doc.LoadHtml(html); SanitizeHtmlNode(doc.DocumentNode); //return doc.DocumentNode.WriteTo(); string output = null; // Use an XmlTextWriter to create self-closing tags using (StringWriter sw = new StringWriter()) { XmlWriter writer = new XmlTextWriter(sw); doc.DocumentNode.WriteTo(writer); output = sw.ToString(); // strip off XML doc header if (!string.IsNullOrEmpty(output)) { int at = output.IndexOf("?>"); output = output.Substring(at + 2); } writer.Close(); } doc = null; return output; } private void SanitizeHtmlNode(HtmlNode node) { if (node.NodeType == HtmlNodeType.Element) { // check for blacklist items and remove if (BlackList.Contains(node.Name)) { node.Remove(); return; } // remove CSS Expressions and embedded script links if (node.Name == "style") { if (string.IsNullOrEmpty(node.InnerText)) { if (node.InnerHtml.Contains("expression") || node.InnerHtml.Contains("javascript:")) node.ParentNode.RemoveChild(node); } } // remove script attributes if (node.HasAttributes) { for (int i = node.Attributes.Count - 1; i >= 0; i--) { HtmlAttribute currentAttribute = node.Attributes[i]; var attr = currentAttribute.Name.ToLower(); var val = currentAttribute.Value.ToLower(); span style="background: white; color: green">// remove event handlers if (attr.StartsWith("on")) node.Attributes.Remove(currentAttribute); // remove script links else if ( //(attr == "href" || attr== "src" || attr == "dynsrc" || attr == "lowsrc") && val != null && val.Contains("javascript:")) node.Attributes.Remove(currentAttribute); // Remove CSS Expressions else if (attr == "style" && val != null && val.Contains("expression") || val.Contains("javascript:") || val.Contains("vbscript:")) node.Attributes.Remove(currentAttribute); } } } // Look through child nodes recursively if (node.HasChildNodes) { for (int i = node.ChildNodes.Count - 1; i >= 0; i--) { SanitizeHtmlNode(node.ChildNodes[i]); } } } } } Please note: Use this as a starting point only for your own parsing and review the code for your specific use case! If your needs are less lenient than mine were you can you can make this much stricter by not allowing src and href attributes or CSS links if your HTML doesn't allow it. You can also check links for external URLs and disallow those - lots of options.  The code is simple enough to make it easy to extend to fit your use cases more specifically. It's also quite easy to make this code work using a WhiteList approach if you want to go that route. The code above is semi-generic for allowing full featured HTML fragments that only disallow script related content. The Sanitize method walks through each node of the document and then recursively drills into all of its children until the entire document has been traversed. Note that the code here uses an XmlTextWriter to write output - this is done to preserve XHTML style self-closing tags which are otherwise left as non-self-closing tags. The sanitizer code scans for blacklist elements and removes those elements not allowed. Note that the blacklist is configurable either in the instance class as a property or in the static method via the string parameter list. Additionally the code goes through each element's attributes and looks for a host of rules gleaned from some of the XSS cheat sheets listed at the end of the post. Clearly there are a lot more XSS vulnerabilities, but a lot of them apply to ancient browsers (IE6 and versions of Netscape) - many of these glaring holes (like CSS expressions - WTF IE?) have been removed in modern browsers. What a Pain To be honest this is NOT a piece of code that I wanted to write. I think building anything related to XSS is better left to people who have far more knowledge of the topic than I do. Unfortunately, I was unable to find a tool that worked even closely for me, or even provided a working base. For the project I was working on I had no choice and I'm sharing the code here merely as a base line to start with and potentially expand on for specific needs. It's sad that Microsoft Web Protection Library is currently such a train wreck - this is really something that should come from Microsoft as the systems vendor or possibly a third party that provides security tools. Luckily for my application we are dealing with a authenticated and validated users so the user base is fairly well known, and relatively small - this is not a wide open Internet application that's directly public facing. As I mentioned earlier in the post, if I had my way I would simply not allow this type of raw HTML input in the first place, and instead rely on a more controlled HTML input mechanism like MarkDown or even a good HTML Edit control that can provide some limits on what types of input are allowed. Alas in this case I was overridden and we had to go forward and allow *any* raw HTML posted. Sometimes I really feel sad that it's come this far - how many good applications and tools have been thwarted by fear of XSS (or worse) attacks? So many things that could be done *if* we had a more secure browser experience and didn't have to deal with every little script twerp trying to hack into Web pages and obscure browser bugs. So much time wasted building secure apps, so much time wasted by others trying to hack apps… We're a funny species - no other species manages to waste as much time, effort and resources as we humans do :-) Resources Code on GitHub Html Agility Pack XSS Cheat Sheet XSS Prevention Cheat Sheet Microsoft Web Protection Library (AntiXss) StackOverflow Links: http://stackoverflow.com/questions/341872/html-sanitizer-for-net http://blog.stackoverflow.com/2008/06/safe-html-and-xss/ http://code.google.com/p/subsonicforums/source/browse/trunk/SubSonic.Forums.Data/HtmlScrubber.cs?r=61© Rick Strahl, West Wind Technologies, 2005-2012Posted in Security  HTML  ASP.NET  JavaScript   Tweet !function(d,s,id){var js,fjs=d.getElementsByTagName(s)[0];if(!d.getElementById(id)){js=d.createElement(s);js.id=id;js.src="//platform.twitter.com/widgets.js";fjs.parentNode.insertBefore(js,fjs);}}(document,"script","twitter-wjs"); (function() { var po = document.createElement('script'); po.type = 'text/javascript'; po.async = true; po.src = 'https://apis.google.com/js/plusone.js'; var s = document.getElementsByTagName('script')[0]; s.parentNode.insertBefore(po, s); })();

    Read the article

  • Building a jQuery Plug-in to make an HTML Table scrollable

    - by Rick Strahl
    Today I got a call from a customer and we were looking over an older application that uses a lot of tables to display financial and other assorted data. The application is mostly meta-data driven with lots of layout formatting automatically driven through meta data rather than through explicit hand coded HTML layouts. One of the problems in this apps are tables that display a non-fixed amount of data. The users of this app don't want to use paging to see more data, but instead want to display overflow data using a scrollbar. Many of the forms are very densely populated, often with multiple data tables that display a few rows of data in the UI at the most. This sort of layout does not lend itself well to paging, but works much better with scrollable data. Unfortunately scrollable tables are not easily created. HTML Tables are mangy beasts as anybody who's done any sort of Web development knows. Tables are finicky when it comes to styling and layout, and they have many funky quirks, especially when it comes to scrolling both of the table rows themselves or even the child columns. There's no built-in way to make tables scroll and to lock headers while you do, and while you can embed a table (or anything really) into a scrolling div with something like this: <div style="position:relative; overflow: hidden; overflow-y: scroll; height: 200px; width: 400px;"> <table id="table" style="width: 100%" class="blackborder" > <thead> <tr class="gridheader"> <th>Column 1</th> <th>Column 2</th> <th>Column 3</th> <th >Column 4</th> </tr> </thead> <tbody> <tr> <td>Column 1 Content</td> <td>Column 2 Content</td> <td>Column 3 Content</td> <td>Column 4 Content</td> </tr> <tr> <td>Column 1 Content</td> <td>Column 2 Content</td> <td>Column 3 Content</td> <td>Column 4 Content</td> </tr> … </tbody> </table> </div> </div> that won't give a very satisfying visual experience: Both the header and body scroll which looks odd. You lose context as soon as the header scrolls off the top and when you reach the bottom of the list the bottom outline of the table shows which also looks off. The the side bar shows all the way down the length of the table yet another visual miscue. In a pinch this will work, but it's ugly. What's out there? Before we go further here you should know that there are a few capable grid plug-ins out there already. Among them: Flexigrid (can work of any table as well as with AJAX data) jQuery Scrollable Table Plug-in (feature similar to what I need but not quite) jqGrid (mostly an Ajax Grid which is very powerful and works very well) But in the end none of them fit the bill of what I needed in this situation. All of these require custom CSS and some of them are fairly complex to restyle. Others are AJAX only or work better with AJAX loaded data. However, I need to actually try (as much as possible) to maintain the original styling of the tables without requiring extensive re-styling. Building the makeTableScrollable() Plug-in To make a table scrollable requires rearranging the table a bit. In the plug-in I built I create two <div> tags and split the table into two: one for the table header and one for the table body. The bottom <div> tag then contains only the table's row data and can be scrolled while the header stays fixed. Using jQuery the basic idea is pretty simple: You create the divs, copy the original table into the bottom, then clone the table, clear all content append the <thead> section, into new table and then copy that table into the second header <div>. Easy as pie, right? Unfortunately it's a bit more complicated than that as it's tricky to get the width of the table right to account for the scrollbar (by adding a small column) and making sure the borders properly line up for the two tables. A lot of style settings have to be made to ensure the table is a fixed size, to remove and reattach borders, to add extra space to allow for the scrollbar and so forth. The end result of my plug-in is a table with a scrollbar. Using the same table I used earlier the result looks like this: To create it, I use the following jQuery plug-in logic to select my table and run the makeTableScrollable() plug-in against the selector: $("#table").makeTableScrollable( { cssClass:"blackborder"} ); Without much further ado, here's the short code for the plug-in: (function ($) { $.fn.makeTableScrollable = function (options) { return this.each(function () { var $table = $(this); var opt = { // height of the table height: "250px", // right padding added to support the scrollbar rightPadding: "10px", // cssclass used for the wrapper div cssClass: "" } $.extend(opt, options); var $thead = $table.find("thead"); var $ths = $thead.find("th"); var id = $table.attr("id"); var cssClass = $table.attr("class"); if (!id) id = "_table_" + new Date().getMilliseconds().ToString(); $table.width("+=" + opt.rightPadding); $table.css("border-width", 0); // add a column to all rows of the table var first = true; $table.find("tr").each(function () { var row = $(this); if (first) { row.append($("<th>").width(opt.rightPadding)); first = false; } else row.append($("<td>").width(opt.rightPadding)); }); // force full sizing on each of the th elemnts $ths.each(function () { var $th = $(this); $th.css("width", $th.width()); }); // Create the table wrapper div var $tblDiv = $("<div>").css({ position: "relative", overflow: "hidden", overflowY: "scroll" }) .addClass(opt.cssClass); var width = $table.width(); $tblDiv.width(width).height(opt.height) .attr("id", id + "_wrapper") .css("border-top", "none"); // Insert before $tblDiv $tblDiv.insertBefore($table); // then move the table into it $table.appendTo($tblDiv); // Clone the div for header var $hdDiv = $tblDiv.clone(); $hdDiv.empty(); var width = $table.width(); $hdDiv.attr("style", "") .css("border-bottom", "none") .width(width) .attr("id", id + "_wrapper_header"); // create a copy of the table and remove all children var $newTable = $($table).clone(); $newTable.empty() .attr("id", $table.attr("id") + "_header"); $thead.appendTo($newTable); $hdDiv.insertBefore($tblDiv); $newTable.appendTo($hdDiv); $table.css("border-width", 0); }); } })(jQuery); Oh sweet spaghetti code :-) The code starts out by dealing the parameters that can be passed in the options object map: height The height of the full table/structure. The height of the outside wrapper container. Defaults to 200px. rightPadding The padding that is added to the right of the table to account for the scrollbar. Creates a column of this width and injects it into the table. If too small the rightmost column might get truncated. if too large the empty column might show. cssClass The CSS class of the wrapping container that appears to wrap the table. If you want a border around your table this class should probably provide it since the plug-in removes the table border. The rest of the code is obtuse, but pretty straight forward. It starts by creating a new column in the table to accommodate the width of the scrollbar and avoid clipping of text in the rightmost column. The width of the columns is explicitly set in the header elements to force the size of the table to be fixed and to provide the same sizing when the THEAD section is moved to a new copied table later. The table wrapper div is created, formatted and the table is moved into it. The new wrapper div is cloned for the header wrapper and configured. Finally the actual table is cloned and cleared of all elements. The original table's THEAD section is then moved into the new table. At last the new table is added to the header <div>, and the header <div> is inserted before the table wrapper <div>. I'm always amazed how easy jQuery makes it to do this sort of re-arranging, and given of what's happening the amount of code is rather small. Disclaimer: Your mileage may vary A word of warning: I make no guarantees about the code above. It's a first cut and I provided this here mainly to demonstrate the concepts of decomposing and reassembling an HTML layout :-) which jQuery makes so nice and easy. I tested this component against the typical scenarios we plan on using it for which are tables that use a few well known styles (or no styling at all). I suspect if you have complex styling on your <table> tag that things might not go so well. If you plan on using this plug-in you might want to minimize your styling of the table tag and defer any border formatting using the class passed in via the cssClass parameter, which ends up on the two wrapper div's that wrap the header and body rows. There's also no explicit support for footers. I rarely if ever use footers (when not using paging that is), so I didn't feel the need to add footer support. However, if you need that it's not difficult to add - the logic is the same as adding the header. The plug-in relies on a well-formatted table that has THEAD and TBODY sections along with TH tags in the header. Note that ASP.NET WebForm DataGrids and GridViews by default do not generate well-formatted table HTML. You can look at my Adding proper THEAD sections to a GridView post for more info on how to get a GridView to render properly. The plug-in has no dependencies other than jQuery. Even with the limitations in mind I hope this might be useful to some of you. I know I've already identified a number of places in my own existing applications where I will be plugging this in almost immediately. Resources Download Sample and Plug-in code Latest version in the West Wind Web & AJAX Toolkit Repository © Rick Strahl, West Wind Technologies, 2005-2011Posted in jQuery  HTML  ASP.NET  

    Read the article

  • LWJGL Voxel game, glDrawArrays

    - by user22015
    I've been learning about 3D for a couple days now. I managed to create a chunk (8x8x8). Add optimization so it only renders the active and visible blocks. Then I added so it only draws the faces which don't have a neighbor. Next what I found from online research was that it is better to use glDrawArrays to increase performance. So I restarted my little project. Render an entire chunck, add optimization so it only renders active and visible blocks. But now I want to add so it only draws the visible faces while using glDrawArrays. This is giving me some trouble with calling glDrawArrays because I'm passing a wrong count parameter. > # A fatal error has been detected by the Java Runtime Environment: > # > # EXCEPTION_ACCESS_VIOLATION (0xc0000005) at pc=0x0000000006e31a03, pid=1032, tid=3184 > # Stack: [0x00000000023a0000,0x00000000024a0000], sp=0x000000000249ef70, free space=1019k Native frames: (J=compiled Java code, j=interpreted, Vv=VM code, C=native code) C [ig4icd64.dll+0xa1a03] Java frames: (J=compiled Java code, j=interpreted, Vv=VM code) j org.lwjgl.opengl.GL11.nglDrawArrays(IIIJ)V+0 j org.lwjgl.opengl.GL11.glDrawArrays(III)V+20 j com.vox.block.Chunk.render()V+410 j com.vox.ChunkManager.render()V+30 j com.vox.Game.render()V+11 j com.vox.GameHandler.render()V+12 j com.vox.GameHandler.gameLoop()V+15 j com.vox.Main.main([Ljava/lang/StringV+13 v ~StubRoutines::call_stub public class Chunk { public final static int[] DIM = { 8, 8, 8}; public final static int CHUNK_SIZE = (DIM[0] * DIM[1] * DIM[2]); Block[][][] blocks; private int index; private int vBOVertexHandle; private int vBOColorHandle; public Chunk(int index) { this.index = index; vBOColorHandle = GL15.glGenBuffers(); vBOVertexHandle = GL15.glGenBuffers(); blocks = new Block[DIM[0]][DIM[1]][DIM[2]]; for(int x = 0; x < DIM[0]; x++){ for(int y = 0; y < DIM[1]; y++){ for(int z = 0; z < DIM[2]; z++){ blocks[x][y][z] = new Block(); } } } } public void render(){ Block curr; FloatBuffer vertexPositionData2 = BufferUtils.createFloatBuffer(CHUNK_SIZE * 6 * 12); FloatBuffer vertexColorData2 = BufferUtils.createFloatBuffer(CHUNK_SIZE * 6 * 12); int counter = 0; for(int x = 0; x < DIM[0]; x++){ for(int y = 0; y < DIM[1]; y++){ for(int z = 0; z < DIM[2]; z++){ curr = blocks[x][y][z]; boolean[] neightbours = validateNeightbours(x, y, z); if(curr.isActive() && !neightbours[6]) { float[] arr = curr.createCube((index*DIM[0]*Block.BLOCK_SIZE*2) + x*2, y*2, z*2, neightbours); counter += arr.length; vertexPositionData2.put(arr); vertexColorData2.put(createCubeVertexCol(curr.getCubeColor())); } } } } vertexPositionData2.flip(); vertexPositionData2.flip(); FloatBuffer vertexPositionData = BufferUtils.createFloatBuffer(vertexColorData2.position()); FloatBuffer vertexColorData = BufferUtils.createFloatBuffer(vertexColorData2.position()); for(int i = 0; i < vertexPositionData2.position(); i++) vertexPositionData.put(vertexPositionData2.get(i)); for(int i = 0; i < vertexColorData2.position(); i++) vertexColorData.put(vertexColorData2.get(i)); vertexColorData.flip(); vertexPositionData.flip(); GL15.glBindBuffer(GL15.GL_ARRAY_BUFFER, vBOVertexHandle); GL15.glBufferData(GL15.GL_ARRAY_BUFFER, vertexPositionData, GL15.GL_STATIC_DRAW); GL15.glBindBuffer(GL15.GL_ARRAY_BUFFER, 0); GL15.glBindBuffer(GL15.GL_ARRAY_BUFFER, vBOColorHandle); GL15.glBufferData(GL15.GL_ARRAY_BUFFER, vertexColorData, GL15.GL_STATIC_DRAW); GL15.glBindBuffer(GL15.GL_ARRAY_BUFFER, 0); GL11.glPushMatrix(); GL15.glBindBuffer(GL15.GL_ARRAY_BUFFER, vBOVertexHandle); GL11.glVertexPointer(3, GL11.GL_FLOAT, 0, 0L); GL15.glBindBuffer(GL15.GL_ARRAY_BUFFER, vBOColorHandle); GL11.glColorPointer(3, GL11.GL_FLOAT, 0, 0L); System.out.println("Counter " + counter); GL11.glDrawArrays(GL11.GL_LINE_LOOP, 0, counter); GL11.glPopMatrix(); //blocks[r.nextInt(DIM[0])][2][r.nextInt(DIM[2])].setActive(false); } //Random r = new Random(); private float[] createCubeVertexCol(float[] CubeColorArray) { float[] cubeColors = new float[CubeColorArray.length * 4 * 6]; for (int i = 0; i < cubeColors.length; i++) { cubeColors[i] = CubeColorArray[i % CubeColorArray.length]; } return cubeColors; } private boolean[] validateNeightbours(int x, int y, int z) { boolean[] bools = new boolean[7]; bools[6] = true; bools[6] = bools[6] && (bools[0] = y > 0 && y < DIM[1]-1 && blocks[x][y+1][z].isActive());//top bools[6] = bools[6] && (bools[1] = y > 0 && y < DIM[1]-1 && blocks[x][y-1][z].isActive());//bottom bools[6] = bools[6] && (bools[2] = z > 0 && z < DIM[2]-1 && blocks[x][y][z+1].isActive());//front bools[6] = bools[6] && (bools[3] = z > 0 && z < DIM[2]-1 && blocks[x][y][z-1].isActive());//back bools[6] = bools[6] && (bools[4] = x > 0 && x < DIM[0]-1 && blocks[x+1][y][z].isActive());//left bools[6] = bools[6] && (bools[5] = x > 0 && x < DIM[0]-1 && blocks[x-1][y][z].isActive());//right return bools; } } public class Block { public static final float BLOCK_SIZE = 1f; public enum BlockType { Default(0), Grass(1), Dirt(2), Water(3), Stone(4), Wood(5), Sand(6), LAVA(7); int BlockID; BlockType(int i) { BlockID=i; } } private boolean active; private BlockType type; public Block() { this(BlockType.Default); } public Block(BlockType type){ active = true; this.type = type; } public float[] getCubeColor() { switch (type.BlockID) { case 1: return new float[] { 1, 1, 0 }; case 2: return new float[] { 1, 0.5f, 0 }; case 3: return new float[] { 0, 0f, 1f }; default: return new float[] {0.5f, 0.5f, 1f}; } } public float[] createCube(float x, float y, float z, boolean[] neightbours){ int counter = 0; for(boolean b : neightbours) if(!b) counter++; float[] array = new float[counter*12]; int offset = 0; if(!neightbours[0]){//top array[offset++] = x*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE + BLOCK_SIZE; } if(!neightbours[1]){//bottom array[offset++] = x*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE - BLOCK_SIZE; } if(!neightbours[2]){//front array[offset++] = x*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE + BLOCK_SIZE; } if(!neightbours[3]){//back array[offset++] = x*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE - BLOCK_SIZE; } if(!neightbours[4]){//left array[offset++] = x*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE + BLOCK_SIZE; } if(!neightbours[5]){//right array[offset++] = x*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = x*BLOCK_SIZE + BLOCK_SIZE; array[offset++] = y*BLOCK_SIZE - BLOCK_SIZE; array[offset++] = z*BLOCK_SIZE - BLOCK_SIZE; } return Arrays.copyOf(array, offset); } public boolean isActive() { return active; } public void setActive(boolean active) { this.active = active; } public BlockType getType() { return type; } public void setType(BlockType type) { this.type = type; } } I highlighted the code I'm concerned about in this following screenshot: - http://imageshack.us/a/img820/7606/18626782.png - (Not allowed to upload images yet) I know the code is a mess but I'm just testing stuff so I wasn't really thinking about it.

    Read the article

  • Understanding Collabnet&rsquo;s LDAP binding

    - by Robert May
    We want to use both subversion usernames and passwords as well as Active Directory for our authentication on our Collabnet subversion server. This has proven to be more of a challenge than we thought, mostly because Collabnet’s documentation is pretty poor. To supplement that documentation, I add my own. The first thing to understand is that the attribute that you specify in the LDAP Login Attribute ONLY applies to lookups done for the user.  It does NOT apply to the LDAP Bind DN field.  Second, know that the debug logs (error is the one you want) don’t give you debug information for the bind DN, just the login attempts.  Third, by default, Active Directory does not allow anonymous binds, so you MUST put in a user that has the authority to query the Active Directory ldap. Because of these items, the values to set in those fields can be somewhat confusing.  You’ll want to have ADSI Edit handy (I also used ldp, which is installed by default on server 2008), since ADSI Edit can help you find stuff in your active directory.  Be careful, you can also break stuff. Here’s what should go into those fields. LDAP Security Level:  Should be set to None LDAP Server Host:  Should be set to the full name of a domain controller in your domain.  For example, dc.mydomain.com LDAP Server Port:  Should be set to 3268.  The default port of 389 will only query that specific server, not the global catalog.  By setting it to 3268, the global catalog will be queried, which is probably what you want. LDAP Base DN:  Should be set to the location where you want the search for users to begin.  By default, the search scope is set to sub, so all child organizational units below this setting will be searched.  In my case, I had created an OU specifically for users for group policies.  My value ended up being:  OU=MyOu,DC=domain,DC=org.   However, if you’re pointing it to the default Users folder, you may end up with something like CN=Users,DC=domain,DC=org (or com or whatever).  Again, use ADSI edit and use the Distinguished Name that it shows. LDAP Bind DN:  This needs to be the Distinguished Name of the user that you’re going to use for binding (i.e. the user you’ll be impersonating) for doing queries.  In my case, it ended up being CN=svn svn,OU=MyOu,DC=domain,DC=org.  Why the double svn, you might ask?  That’s because the first and last name fields are set to svn and by default, the distinguished name is the first and last name fields!  That’s important.  Its NOT the username or account name!  Again, use ADSI edit, browse to the username you want to use, right click and select properties, and then search the attributes for the Distinguished Name.  Once you’ve found that, select it and click View and you can copy and paste that into this field. LDAP Bind Password:  This is the password for the account in the Bind DN LDAP login Attribute: sAMAccountName.  If you leave this blank, uid is used, which may not even be set.  This tells it to use the Account Name field that’s defined under the account tab for users in Active Directory Users and Computers.  Note that this attribute DOES NOT APPLY to the LDAP Bind DN.  You must use the full distinguished name of the bind DN.  This attribute allows users to type their username and password for authentication, rather than typing their distinguished name, which they probably don’t know. LDAP Search Scope:  Probably should stay at sub, but could be different depending on your situation. LDAP Filter:  I left mine blank, but you could provide one to limit what you want to see.  LDP would be helpful for determining what this is. LDAP Server Certificate Verification:  I left it checked, but didn’t try it without it being checked. Hopefully, this will save some others pain when trying to get Collabnet setup. Technorati Tags: Subversion,collabnet

    Read the article

  • jQuery, array form radio button name problem.

    - by borayeris
    <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <head> <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> <title>click div to select hidden options</title> <script type="text/javascript" src="jquery-1.4.4.js"></script> <style type="text/css"> .clickDiv { width:50px; height:50px; cursor:crosshair; } .red {border:1px #000 solid;} .green {border:1px #000 solid;} .redBG {background:#F00;} .greenBG {background:#0F0;} </style> <script type="text/javascript"> $(function() { $('div.clickDiv.red').click(function(){ var secilenMadde=$(this).attr('madde'); $('div#write').text(secilenMadde); $('input[name='+secilenMadde+'][value=red]').attr('checked', 'checked'); $('div.clickDiv.red[madde='+secilenMadde+']').addClass('redBG'); $('div.clickDiv.green[madde='+secilenMadde+']').removeClass('greenBG'); }); $('div.clickDiv.green').click(function(){ var secilenMadde=$(this).attr('madde'); $('div#write').text(secilenMadde); $('input[name='+secilenMadde+'][value=green]').attr('checked', 'checked'); $('div.clickDiv.green[madde='+secilenMadde+']').addClass('greenBG'); $('div.clickDiv.red[madde='+secilenMadde+']').removeClass('redBG'); }); }); </script> </head> <body> <div id="write"></div> <form id="formId" name="formName" method="post"> <table> <tr> <td><div class="clickDiv red" madde="line1"></div></td> <td><div class="clickDiv green" madde="line1"></div></td> </tr> <tr> <td><div class="clickDiv red" madde="line2"></div></td> <td><div class="clickDiv green" madde="line2"></div></td> </tr> </table> <label for="line1red"><input id="line1red" type="radio" name="line1" value="red" /> Red</label> <label for="line1green"><input id="line1green" type="radio" name="line1" value="green" /> Green</label><br /> <label for="line2red"><input type="radio" name="line2" value="red" /> Red</label> <label for="line2green"><input type="radio" name="line2" value="green" /> Green</label> </form> </body> </html> This works. <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <head> <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> <title>click div to select hidden options</title> <script type="text/javascript" src="jquery-1.4.4.js"></script> <style type="text/css"> .clickDiv { width:50px; height:50px; cursor:crosshair; } .red {border:1px #000 solid;} .green {border:1px #000 solid;} .redBG {background:#F00;} .greenBG {background:#0F0;} </style> <script type="text/javascript"> $(function() { $('div.clickDiv.red').click(function(){ var secilenMadde=$(this).attr('madde'); $('div#write').text(secilenMadde); $('input[name='+secilenMadde+'][value=red]').attr('checked', 'checked'); $('div.clickDiv.red[madde='+secilenMadde+']').addClass('redBG'); $('div.clickDiv.green[madde='+secilenMadde+']').removeClass('greenBG'); }); $('div.clickDiv.green').click(function(){ var secilenMadde=$(this).attr('madde'); $('div#write').text(secilenMadde); $('input[name='+secilenMadde+'][value=green]').attr('checked', 'checked'); $('div.clickDiv.green[madde='+secilenMadde+']').addClass('greenBG'); $('div.clickDiv.red[madde='+secilenMadde+']').removeClass('redBG'); }); }); </script> </head> <body> <div id="write"></div> <form id="formId" name="formName" method="post"> <table> <tr> <td><div class="clickDiv red" madde="line[1]"></div></td> <td><div class="clickDiv green" madde="line[1]"></div></td> </tr> <tr> <td><div class="clickDiv red" madde="line[2]"></div></td> <td><div class="clickDiv green" madde="line[2]"></div></td> </tr> </table> <label for="line1red"><input id="line1red" type="radio" name="line[1]" value="red" /> Red</label> <label for="line1green"><input id="line1green" type="radio" name="line[1]" value="green" /> Green</label><br /> <label for="line2red"><input type="radio" name="line[2]" value="red" /> Red</label> <label for="line2green"><input type="radio" name="line[2]" value="green" /> Green</label> </form> </body> </html> This doesn't. I need input names as an array but it breaks my script. Why?

    Read the article

  • WPF binding ComboBox to enum (with a twist)

    - by Carlo
    Well the problem is that I have this enum, BUT I don't want the combobox to show the values of the enum. This is the enum: public enum Mode { [Description("Display active only")] Active, [Description("Display selected only")] Selected, [Description("Display active and selected")] ActiveAndSelected } So in the ComboBox instead of displaying Active, Selected or ActiveAndSelected, I want to display the DescriptionProperty for each value of the enum. I do have an extension method called GetDescription() for the enum: public static string GetDescription(this Enum enumObj) { FieldInfo fieldInfo = enumObj.GetType().GetField(enumObj.ToString()); object[] attribArray = fieldInfo.GetCustomAttributes(false); if (attribArray.Length == 0) { return enumObj.ToString(); } else { DescriptionAttribute attrib = attribArray[0] as DescriptionAttribute; return attrib.Description; } } So is there a way I can bind the enum to the ComboBox AND show it's content with the GetDescription extension method? Thanks!

    Read the article

  • Using CHDataStructures.framework on iPhone

    - by nununo
    Hi, I'm new to iPhone programming and I'm trying to use CHDataStructures in my project. But I'm running into some issues: When I directly try to build it right after download I get the error "Foundation/Foundation.h" no such file or directory. The Active SDK is "Use Base SDK" and the active architecture is x86_64. I believe I should set the Active SDK to the iPhone SDK but it isn't listed there; At some point (I don't remember how) I managed to tweak it and I got the iPhone SDK (simulator) in the active SDK but when I tried to build it I got the following error: "target specifies product type 'com.apple.product-type.framework', but there's no such product type for the 'iphonesimulator' platform"; And now I'm stuck. What am I doing wrong? Thanks in advance, Nuno

    Read the article

  • Delphi and Microsoft ATL security issue

    - by Jens Nordenbro
    My impression is that standard Delphi uses the Win32 API. Recently Microsoft has been communicating a problem regarding ATL that requires application developers to rebuild ATL-using applications after installing an update on their machines. Will this practice be the general case also for Delphi developers, or are they in the clear with the exception of Delphi code using third party ATL COM objects? Sources: Microsoft Security: Protect your computer from the Active Template Library (ATL) security vulnerability MSDN VC++ DevCenter: Active Template Library Security Update for Developers Microsoft Security Advisory (973882): Vulnerabilities in Microsoft Active Template Library (ATL) Could Allow Remote Code Execution Microsoft Security Bulletin MS09-034 - Critical: Cumulative Security Update for Internet Explorer (972260) Microsoft Security Bulletin MS09-035 - Moderate: Vulnerabilities in Visual Studio Active Template Library Could Allow Remote Code Execution (969706)

    Read the article

  • Using named_scopes on the join model of a has_many :through

    - by uberllama
    Hi folks. I've been beating my head against the wall on something that on the surface should be very simple. Lets say I have the following simplified models: user.rb has_many :memberships has_many :groups, :through => :memberships membership.rb belongs_to :group belongs_to :user STATUS_CODES = {:admin => 1, :member => 2, :invited => 3} named_scope :active, :conditions => {:status => [[STATUS_CODES[:admin], STATUS_CODES[:member]]} group.rb has_many :memberships has_many :users, :through => :memberships Simple, right? So what I want to do is get a collection of all the groups a user is active in, using the existing named scope on the join model. Something along the lines of User.find(1).groups.active. Obviously this doesn't work. But as it stands, I need to do something like User.find(1).membrships.active.all(:include => :group) which returns a collection of memberships plus groups. I don't want that. I know I can add another has_many on the User model with conditions that duplicate the :active named_scope on the Membership model, but that's gross. has_many :active_groups, :through => :memberships, :source => :group, :conditions => ... So my question: is there a way of using intermediary named scopes when traversing directly between models? Many thanks.

    Read the article

  • openssl api verify the public key matches private key

    - by AC
    How do I write an openssl server that on a single port has two different active RSA private keys? The openssl documentation seems to implies there can only be one rsa private key active at time with in a context. So I was thinking I have two active context, but what is the code to handle figuring out which connection matches which context. Or am I going about this the wrong way.

    Read the article

  • propertyregex removes return characters in multiline

    - by javydreamercsw
    I'm using ants propertyregex method to change a property and it works fine up to a point. I'm lossing return characters. Here's what I'm trying to change: cluster.path=\ ${nbplatform.active.dir}/harness:\ ${nbplatform.active.dir}/platform:\ ${nbplatform.active.dir}/nb This is in a .properties file. So I'm trying to change it like this: <propertyregex property="cluster.path" input="${cluster.path}" regexp="nbplatform.active.dir" replace="xplatform.base" global="true" override="true"/> The stuff is replaced but I get: cluster.path= ${xplatform.base}/harness\: ${xplatform.base}/platform\: ${xplatform.base}/nb This brakes logic down the line not controlled by me (Netbeans) that uses the ':' as delimiter. Any idea?

    Read the article

  • How do I prevent the concurrent execution of a javascript function?

    - by RyanV
    I am making a ticker similar to the "From the AP" one at The Huffington Post, using jQuery. The ticker rotates through a ul, either by user command (clicking an arrow) or by an auto-scroll. Each list-item is display:none by default. It is revealed by the addition of a "showHeadline" class which is display:list-item. HTML for the UL Looks like this: <ul class="news" id="news"> <li class="tickerTitle showHeadline">Test Entry</li> <li class="tickerTitle">Test Entry2</li> <li class="tickerTitle">Test Entry3</li> </ul> When the user clicks the right arrow, or the auto-scroll setTimeout goes off, it runs a tickForward() function: function tickForward(){ var $active = $('#news li.showHeadline'); var $next = $active.next(); if($next.length==0) $next = $('#news li:first'); $active.stop(true, true); $active.fadeOut('slow', function() {$active.removeClass('showHeadline');}); setTimeout(function(){$next.fadeIn('slow', function(){$next.addClass('showHeadline');})}, 1000); if(isPaused == true){ } else{ startScroll() } }; This is heavily inspired by Jon Raasch's A Simple jQuery Slideshow. Basically, find what's visible, what should be visible next, make the visible thing fade and remove the class that marks it as visible, then fade in the next thing and add the class that makes it visible. Now, everything is hunky-dory if the auto-scroll is running, kicking off tickForward() once every three seconds. But if the user clicks the arrow button repeatedly, it creates two negative conditions: Rather than advance quickly through the list for just the number of clicks made, it continues scrolling at a faster-than-normal rate indefinitely. It can produce a situation where two (or more) list items are given the .showHeadline class, so there's overlap on the list. I can see these happening (especially #2) because the tickForward() function can run concurrently with itself, producing different sets of $active and $next. So I think my question is: What would be the best way to prevent concurrent execution of the tickForward() method? Some things I have tried or considered: Setting a Flag: When tickForward() runs, it sets an isRunning flag to true, and sets it back to false right before it ends. The logic for the event handler is set to only call tickForward() if isRunning is false. I tried a simple implementation of this, and isRunning never appeared to be changed. The jQuery queue(): I think it would be useful to queue up the tickForward() commands, so if you clicked it five times quickly, it would still run as commanded but wouldn't run concurrently. However, in my cursory reading on the subject, it appears that a queue has to be attached to the object its queue applies to, and since my tickForward() method affects multiple lis, I don't know where I'd attach it.

    Read the article

  • PostgreSQL Crosstab Query

    - by schone
    Hi all, Does any one know how to create crosstab queries in PostgreSQL? For example I have the following table: Section Status Count A Active 1 A Inactive 2 B Active 4 B Inactive 5 I would like the query to return the following crosstab: Section Active Inactive A 1 2 B 4 5 Is this possible? Thanks!

    Read the article

< Previous Page | 85 86 87 88 89 90 91 92 93 94 95 96  | Next Page >