Search Results

Search found 3130 results on 126 pages for 'half duplex'.

Page 9/126 | < Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >

  • List existing file server permission groups/users

    - by Patrick
    So we have taken over a new client and their existing file server is frankly a mess. We have migrated their old file server from a 2k box to a 2k8 DFS cluster and now I'm looking at rebuilding both the folder structure and their permissions. Unfortunately its been half done with AD groups (poorly named/no description/notes) and half with individuals named in security on the folders themselves. What I'm looking to do is to dump a complete list of all the folders with their security permissions (ideally I'd like to ignore files but not essential). CACLS got me half way there but fails with an odd error message and its output isn't particularly user friendly and I'm working with roughly 2Tb/250,000 files here so I really need something that gives me a bit more functionality. Question : does anyone have any experience of something similar/know of a bit of software that might help me out?

    Read the article

  • How can I further improve the quality of my home videos?

    - by Bob
    So now that I have found out how to deinterlace my videos, I am wondering if there is other software out there that can further help improve the quality of my videos. Some other problems I have noticed is when you move the camera side to side very quickly you can notice tearing in the the picture. That is the top half of the frame doesn't line up with the bottom half, it appears that the bottom half is shifted to the right or left depending on which way the camera is moving. Shaky camera hand is also a problem in some videos. I don't expect any software to be able to correct these problems 100%, especially the shaky hand. I know that using a tripod or something of the sorts is the best way to prevent the shakes, but for preexsiting videos what are the best solutions I can use?

    Read the article

  • Boot problems w/ External HDD

    - by JeremyT
    I'm having a problem with booting a live image off of a USB Hard Drive. I used Startup Disk Creator to make an Ubuntu 11.10 live image on a partition on my external so that I can use it on various computers. I set it up with ~4GB of persistent data So far I've tried it on two computers. One, a Dell, will boot to my external but it loads the select boot device very slowly. It hangs on a screen with an underscore for up to 5 minutes until it allows me to select which drive I want to boot from. After that, it works great. However, on my primary computer it doesn't work at all. It's an Acer from 2009 and it won't even recognize the drive. I don't see it anywhere in BIOS or the select boot disk list. The light on the external will come on at boot just fine so I know it's powering it at this time. Both computers worked perfectly with my 4GB flash drive that I had partitioned half and half (1st half FAT32 and second Ubuntu 11.10 live)

    Read the article

  • How to disable visual effects and compiz 100%

    - by oshirowanen
    UPDATE 1: The problem is not a monitor refresh rate flickering problem, as then the whole screen would be flickering. For me, only the application windows flicker in and out of view, then most of the time, when there do decide to show themselves, they only partly show themselves, like just top half, bottom half, left half, corner missing, window disappears when you try moving it or mouse over it even etc etc. I know it is a visual effect problem as I know my computer cannot handle visual effects and for some reason when the windows do appear partly, I can see the shadows behind the windows. Those shadows are part of the visual effects which are turned on by default for some reason. I get the same problem with 10.04, but can quickly turn off the visual effects by right clicking the desktop, selecting change background image, and in the visual effects tab, I can click on none, which stops all the visual problems. ORIGINAL QUESTION: I am having problems with 11.04 on my computer. For some reason it is enabling visual effects by default in the live cd when it should not be as my computer cannot support such effects. My computer cannot support Unity either, but it defaults to standard gnome with visual effects for some reason. It should be defaulting to standard gnome with no visual effects. THerefore, all I get is a very flickery live cd which makes it very difficult to see anything. So my question is, how do I disable the visual effects from the live cd? To put it simply, the live cd flickering is so bad, that I had to log back into my standard 10.04 install just to write this question, as I just couldn't see enough of the screen because of the flickering in 11.04 to even get to askubuntu.com...

    Read the article

  • Costs/profit of/when starting an indie company

    - by Jack
    In short, I want to start a game company. I do not have much coding experience (just basic understanding and ability to write basic programs), any graphics design experience, any audio mixing experience, or whatever else technical. However, I do have a lot of ideas, great analytical skills and a very logical approach to life. I do not have any friends who are even remotely technical (or creative in regards to games for that matter). So now that we've cleared that up, my question is this: how much, minimally, would it cost me to start such a company? I know that a game could be developed in under half a year, which means it would have to operate for half a year prior, and that's assuming that the people working on the first project do their jobs good, don't leave game breaking bugs, a bunch of minor bugs, etc.. So how much would it cost me, and what would be the likely profit in half a year? I'm looking at minimal costs here, as to do it, I would have to sell my current apartment and buy a new, smaller one, pay taxes, and likely move to US/CA/UK to be closer to technologically advanced people (and be able to speak the language of course). EDIT: I'm looking at a small project for starters, not a huge AAA title.

    Read the article

  • A Myriad of Options

    - by Mark Hesse
    I am currently working with a customer that is close to outgrowing their Exadata X2-2 half rack in both compute and storage capacity.  The platform is used for one of their larger data warehouse applications and the move to Exadata almost two years ago has been a resounding success, forcing them to grow the platform sooner than anticipated. At a recent planning meeting, we started looking at the options for expansion and have developed five alternatives, all of which meet or exceed their growth requirements, yet have different pros and cons in terms of the impact to their production and test environments. The options include an in-rack upgrade to a full rack of Exadata using the recently released X3-2 platform (an option that even applies to an older V2 rack), multi-rack cabling the existing X2-2 to another full rack or half rack X2-2 (and utilizing both compute and storage capacity in the other rack), or simply adding a new X3-2 half rack (and taking advantage of the added compute and flash performance in the X3-2). While the decision is yet to be made, it had me thinking that one of the benefits of Exadata over a traditional database deployment is that when the time comes to expand the platform, there are a myriad of options.

    Read the article

  • Unit Testing-- fundamental goal?

    - by David
    Me and my co-workers had a bit of a disagreement last night about unit testing in our PHP/MySQL application. Half of us argued that when unit testing a function within a class, you should mock everything outside of that class and its parents. The other half of us argued that you SHOULDN'T mock anything that is a direct dependancy of the class either. The specific example was our logging mechanism, which happened through a static Logging class, and we had a number of Logging::log() calls in various locations throughout our application. The first half of us said the Logging mechanism should be faked (mocked) because it would be tested in the Logging unit tests. The second half of us argued that we should include the original Logging class in our unit test so that if we make a change to our logging interface, we'll be able to see if it creates problems in other parts of the application due to failing to update the call interface. So I guess the fundamental question is-- do unit tests serve to test the functionality of a single unit in a closed environment, or show the consequences of changes to a single unit in a larger environment? If it's one of these, how do you accomplish the other?

    Read the article

  • Linux e1000e (Intel networking driver) problems galore, where do I start?

    - by Evan Carroll
    I'm currently having a major problem with e1000e (not working at all) in Ubuntu Maverick (1.0.2-k4), after resume I'm getting a lot of stuff in dmesg: [ 9085.820197] e1000e 0000:02:00.0: PCI INT A disabled [ 9089.907756] e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k4 [ 9089.907762] e1000e: Copyright (c) 1999 - 2009 Intel Corporation. [ 9089.907797] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9089.907827] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9089.907857] e1000e 0000:02:00.0: setting latency timer to 64 [ 9089.908529] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9089.908922] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9089.908954] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9090.024625] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9090.024630] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9090.024712] e1000e 0000:02:00.0: eth0: MAC: 2, PHY: 2, PBA No: 005302-003 [ 9090.109492] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9090.164219] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X and, a bunch of [ 2128.005447] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang: [ 2128.005452] TDH <89> [ 2128.005454] TDT <27> [ 2128.005456] next_to_use <27> [ 2128.005458] next_to_clean <88> [ 2128.005460] buffer_info[next_to_clean]: [ 2128.005463] time_stamp <6e608> [ 2128.005465] next_to_watch <8a> [ 2128.005467] jiffies <6f929> [ 2128.005469] next_to_watch.status <0> [ 2128.005471] MAC Status <80080703> [ 2128.005473] PHY Status <796d> [ 2128.005475] PHY 1000BASE-T Status <4000> [ 2128.005477] PHY Extended Status <3000> [ 2128.005480] PCI Status <10> I decided to compile the latest stable e1000e to 1.2.17, now I'm getting: [ 9895.678050] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.17-NAPI [ 9895.678055] e1000e: Copyright(c) 1999 - 2010 Intel Corporation. [ 9895.678098] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9895.678129] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9895.678162] e1000e 0000:02:00.0: setting latency timer to 64 [ 9895.679136] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.679160] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9895.679192] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9895.791758] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9895.791766] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9895.791850] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003 [ 9895.892464] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.948175] e1000e 0000:02:00.0: irq 44 for MSI/MSI-X [ 9895.949111] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9895.954694] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX/TX [ 9895.954703] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO [ 9895.955157] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9906.832056] eth0: no IPv6 routers present With 1.2.20 I get: [ 9711.525465] e1000e: Intel(R) PRO/1000 Network Driver - 1.2.20-NAPI [ 9711.525472] e1000e: Copyright(c) 1999 - 2010 Intel Corporation. [ 9711.525521] e1000e 0000:02:00.0: Disabling ASPM L1 [ 9711.525554] e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 9711.525586] e1000e 0000:02:00.0: setting latency timer to 64 [ 9711.526460] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9711.526487] e1000e 0000:02:00.0: Disabling ASPM L0s [ 9711.526523] e1000e 0000:02:00.0: (unregistered net_device): PHY reset is blocked due to SOL/IDER session. [ 9711.639763] e1000e 0000:02:00.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:0a:e4:3e:ce:74 [ 9711.639771] e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection [ 9711.639854] e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 2, PBA No: 005302-003 [ 9712.060770] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9712.116195] e1000e 0000:02:00.0: irq 45 for MSI/MSI-X [ 9712.117098] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 9712.122684] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX [ 9712.122693] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO [ 9712.123142] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 9722.920014] eth0: no IPv6 routers present But, I'm still getting these [ 9982.992851] PCI Status <10> [ 9984.993602] e1000e 0000:02:00.0: eth0: Detected Hardware Unit Hang: [ 9984.993606] TDH <5d> [ 9984.993608] TDT <6b> [ 9984.993611] next_to_use <6b> [ 9984.993613] next_to_clean <5b> [ 9984.993615] buffer_info[next_to_clean]: [ 9984.993617] time_stamp <24da80> [ 9984.993619] next_to_watch <5d> [ 9984.993621] jiffies <24f200> [ 9984.993624] next_to_watch.status <0> [ 9984.993626] MAC Status <80080703> [ 9984.993628] PHY Status <796d> [ 9984.993630] PHY 1000BASE-T Status <4000> [ 9984.993632] PHY Extended Status <3000> [ 9984.993635] PCI Status <10> [ 9986.001047] e1000e 0000:02:00.0: eth0: Reset adapter [ 9986.176202] e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: RX/TX [ 9986.176211] e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO I'm not sure where to start troubleshooting this. Any ideas? Here is the result of ethtool -d eth0 MAC Registers ------------- 0x00000: CTRL (Device control register) 0x18100248 Endian mode (buffers): little Link reset: reset Set link up: 1 Invert Loss-Of-Signal: no Receive flow control: enabled Transmit flow control: enabled VLAN mode: disabled Auto speed detect: disabled Speed select: 1000Mb/s Force speed: no Force duplex: no 0x00008: STATUS (Device status register) 0x80080703 Duplex: full Link up: link config TBI mode: disabled Link speed: 10Mb/s Bus type: PCI Express Port number: 0 0x00100: RCTL (Receive control register) 0x04048002 Receiver: enabled Store bad packets: disabled Unicast promiscuous: disabled Multicast promiscuous: disabled Long packet: disabled Descriptor minimum threshold size: 1/2 Broadcast accept mode: accept VLAN filter: enabled Canonical form indicator: disabled Discard pause frames: filtered Pass MAC control frames: don't pass Receive buffer size: 2048 0x02808: RDLEN (Receive desc length) 0x00001000 0x02810: RDH (Receive desc head) 0x00000001 0x02818: RDT (Receive desc tail) 0x000000F0 0x02820: RDTR (Receive delay timer) 0x00000000 0x00400: TCTL (Transmit ctrl register) 0x3103F0FA Transmitter: enabled Pad short packets: enabled Software XOFF Transmission: disabled Re-transmit on late collision: enabled 0x03808: TDLEN (Transmit desc length) 0x00001000 0x03810: TDH (Transmit desc head) 0x00000000 0x03818: TDT (Transmit desc tail) 0x00000000 0x03820: TIDV (Transmit delay timer) 0x00000008 PHY type: IGP2 and ethtool -c eth0 Coalesce parameters for eth0: Adaptive RX: off TX: off stats-block-usecs: 0 sample-interval: 0 pkt-rate-low: 0 pkt-rate-high: 0 rx-usecs: 3 rx-frames: 0 rx-usecs-irq: 0 rx-frames-irq: 0 tx-usecs: 0 tx-frames: 0 tx-usecs-irq: 0 tx-frames-irq: 0 rx-usecs-low: 0 rx-frame-low: 0 tx-usecs-low: 0 tx-frame-low: 0 rx-usecs-high: 0 rx-frame-high: 0 tx-usecs-high: 0 tx-frame-high: 0 Here is also the lspci -vvv for this controller 02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller Subsystem: Lenovo ThinkPad X60s Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 45 Region 0: Memory at ee000000 (32-bit, non-prefetchable) [size=128K] Region 2: I/O ports at 2000 [size=32] Capabilities: [c8] Power Management version 2 Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+) Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME- Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+ Address: 00000000fee0300c Data: 415a Capabilities: [e0] Express (v1) Endpoint, MSI 00 DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, L1 <64us ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset- DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+ RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+ MaxPayload 128 bytes, MaxReadReq 512 bytes DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend- LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <128ns, L1 <64us ClockPM+ Surprise- LLActRep- BwNot- LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+ ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt- LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt- Capabilities: [100 v1] Advanced Error Reporting UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol- UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol- UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol- CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr- AERCap: First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn- Capabilities: [140 v1] Device Serial Number 00-0a-e4-ff-ff-3e-ce-74 Kernel driver in use: e1000e Kernel modules: e1000e I filed a bug on this upstream, still no idea how to get more useful information. Here is a the result of the running that script EEPROM FIX UPDATE $ sudo bash fixeep-82573-dspd.sh eth0 eth0: is a "82573L Gigabit Ethernet Controller" This fixup is applicable to your hardware Your eeprom is up to date, no changes were made Do I still need to do anything? Also here is my EEPROM dump $ sudo ethtool -e eth0 Offset Values ------ ------ 0x0000 00 0a e4 3e ce 74 30 0b b2 ff 51 00 ff ff ff ff 0x0010 53 00 03 02 6b 02 7e 20 aa 17 9a 10 86 80 df 80 0x0020 00 00 00 20 54 7e 00 00 14 00 da 00 04 00 00 27 0x0030 c9 6c 50 31 3e 07 0b 04 8b 29 00 00 00 f0 02 0f 0x0040 08 10 00 00 04 0f ff 7f 01 4d ff ff ff ff ff ff 0x0050 14 00 1d 00 14 00 1d 00 af aa 1e 00 00 00 1d 00 0x0060 00 01 00 40 1f 12 07 40 ff ff ff ff ff ff ff ff 0x0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff 4a e0 I'd also like to note that I used eth0 every day for years and until recently never had an issue.

    Read the article

  • Cisco 2811 router ignored input errors

    - by elbekay
    I've got a Cisco 2811 (AdvIPServices 12.4(25e)) that is showing input errors on both its interfaces, all the errors are of the ignored type. The counter for ignore errors is not increasing continuously, which made me think it would be happening in line with traffic bursts, but there really isn't a large amount of traffic running through it at any time. Both the router interfaces are connected to a 4900 (IPBase 12.2(54)) series switch. The only things I can see are: There is a slight mismatch in duplex/speed negotiation settings, one side is set to auto/auto and one full/auto, however they have negotiated fine. There have been a few fallbacks on the interface buffers, and some trims in the public buffers. Any suggestions for things to look at? I will be correcting the duplex neg settings, and might try a buffer tune, but I don't think it will help.

    Read the article

  • How to Set Linux Bonding Interface to Gigabit

    - by Kyle Brandt
    I have enabled Linux active backup mode bonding. Each interface is a gigabit interface, but the bond interface seems to end up at 100 Megabit: bonding: bond0: Warning: failed to get speed and duplex from eth1, assumed to be 100Mb/sec and Full. ... bnx2: eth0 NIC Link is Up, 1000 Mbps full duplex, receive & transmit flow control ON ... bonding: bond0: backup interface eth1 is now up ethtool apparently can't provide info on bond: sudo ethtool bond0 Settings for bond0: No data available So does this mean I am operating at 100 or 1000 Megabit (My guess is 1000)? If it is only 100, what options in the ifcfg scripts or the modprobe bonding options do I need to sett to make it 1000?

    Read the article

  • VLAN trunking between Juniper EX -> Cisco Catalyst -> and Cisco Router

    - by Hugo Garcia
    I have the following scenario: EX2200 Switch whit ge-0/0/6 set as an access port on VLAN 80 ge-0/0/0 set as a trunk port connected to a catalyst switch and various vlans allowed to pass includin vlan 80 On the Catalyst Switch. port #3 set up as a trunk port that receives traffic from the EX switch. port 46 is set up also as a trunk port that connects to a cisco router. Port #48 is where the host used to be connected host - EX2200 - Catalyst - Router the problem is that this EX2200 is a new addition to the network and the host connected previosly to the catalyst switch. traffic is not getting from the host to the router, but the router can send ARP request to the host. following is the relevant configuration: Catalyst Switch: interface GigabitEthernet1/46 switchport trunk encapsulation dot1q switchport trunk allowed vlan 80,82,83,93,289 switchport mode trunk mtu 1532 media-type rj45 speed 1000 duplex full arp timeout 300 ! interface GigabitEthernet1/48 switchport access vlan 80 switchport mode access mtu 1532 media-type rj45 speed 100 duplex full arp timeout 300 no cdp enable ! EX2200 Switch:

    Read the article

  • Slow download speeds on MacBook Pro

    - by Austin
    Just as the title says, I am getting very low download speeds on my MacBook Pro. I did a speed test at speedtest.net, and am getting 7 MbPS down, .5 up. However, I can only seem to get 270 KB PS max (averaging 100 K), whether on my school's network or on my home network, wired or wireless. I am on Mac OS X 10.5.8, with Google Chrome. My ethernet settings (under System Preferences - Network - Ethernet Connection - Advanced - Ethernet) are set to "Configure Automatically", "Speed: 100TX", "Duplex: full-duplex, flow-control", and "MTU: Standard (1500)". As far as I can tell, there are no throttles or anything between here and the ISP, so... Any ideas on why I'm getting such low download speeds?

    Read the article

  • lacp, cicso 3550, 3560, help with configuration

    - by Flamewires
    Hey all this is a repost from a question I asked on the cisco forums but never got a useful reply. Hey I'm trying to convert the FreeBSD servers at work to dual-gig lagg links from regular gigabit links. Our production servers are on a 3560. I have a small test environment on a 3550. I have achieved fail-over, but am having troubles achieving the speed increase. All servers are running gig intel (em) cards. The configs for the servers are: BSDServer: #!/bin/sh #bring up both interfaces ifconfig em0 up media 1000baseTX mediaopt full-duplex ifconfig em1 up media 1000baseTX mediaopt full-duplex #create the lagg interface ifconfig lagg0 create #set lagg0's protocol to lacp, add both cards to the interface, #and assign it em1's ip/netmask ifconfig lagg0 laggproto lacp laggport em0 laggport em1 ***.***.***.*** netmask 255.255.255.0 The switches are configured as follows: #clear out old junk no int Po1 default int range GigabitEthernet 0/15 - 16 # config ports interface range GigabitEthernet 0/15 - 16 description lagg-test switchport duplex full speed 1000 switchport access vlan 192 spanning-tree portfast channel-group 1 mode active channel-protocol lacp **** switchport trunk encapsulation dot1q **** no shutdown exit interface Port-channel 1 description lagginterface switchport access vlan 192 exit port-channel load-balance src-mac end obviously change 1000's to 100's and GigabitEthernet to FastEthernet for the 3550's config, as that switch has 100Mbit speed ports. With this config on the 3550, I get failover and 92Mbits/sec speed on both links, simultaneously, connecting to 2 hosts.(tested with iperf) Success. However this is only with the "switchport trunk encapsulation dot1q" line. First, I do not understand why I need this, I thought it was only for connecting switches. Is there some other setting which this turns on that is actually responsible for the speed increase? Second, This config does not work on the 3560. I get failover, but not the speed increase. Speeds drop from gig/sec to 500Mbit/sec when I make 2 simultaneous connections to the server with or without the encapsulation line. I should mention that both switches are using source-mac load balancing. In my test I am using Iperf. I have the server(lagg box) setup as the server(iperf -s), and the client computers are client(iperf -c server-ip-address), so the source mac(and IP) are different for both connections. Any ideas/corrections/questions would be helpful, as the gig switches are what I actually need the lagg links on. Ask if you need more information.

    Read the article

  • udp expected behaviour not responding to test result

    - by ernst
    I have a local network topology that is structured as follows: three hosts and a switch in the middle. I am using a switch that supports 10,100,1000 Mbit/s full/half duplex connection. I have configured the hosts with a static ip 172.16.0.1-2-3/25. This is the output of ifconfig eth0 Link encap: Ethernet HWaddr ***** inet addr:172.16.0.3 Bcast:172.16.0.127 Mask:255.255.255.128 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 The output on H1 and H2 is perfectly matchable They are mutually reachable since i have tested the network with ping. I have forced the ethernet interface to work at 10M with ethtool -s eth0 speed 10 duplex full autoneg on this is the output of ethtool eth0 supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full S upported pause frame use: No Supports auto-negotiation: Yes Advertised link modes: 10baseT/Full Advertised pause frame use: Symmetric A dvertised auto-negotiation: Yes Speed: 10Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: g Wake-on: d Current message level: 0x000000ff (255) drv probe link timer ifdown ifup rx_err tx_err Link detected: yes – I am doing an experimental test using nttcp to calculate the GOODPUT in the case that H1 and H2 at the same time send data to H3. Since the three links have the same forced capability and the amount of arrving data speed is 10 from H1+10 from H2--20M to H3 it would be expected a bottleneck effect and, due to the non reliable nature of udp, a packet loss. But this doesn't appen since the output of nttcp application shows the same number of byte sended and received. this is the output of nttcp on h3 nttcp -T -r -u 172.16.0.2 & nttcp -T -r -u 172.16.0.1 [1] 4071 Bytes Real s CPU s Real-MBit/s CPU-MBit/s Calls Real-C/s CPU-C/s l 8388608 13.74 0.05 4.8848 1398.0140 2049 149.14 42684.8 Bytes Real s CPU s Real-MBit/s CPU-MBit/s Calls Real-C/s CPU-C/s l 8388608 14.02 0.05 4.7872 1398.0140 2049 146.17 42684.8 1 8388608 13.56 0.06 4.9500 1118.4065 2051 151.28 34181.1 1 8388608 13.89 0.06 4.8310 1198.3084 2051 147.65 36623.0 – How is this possible? Am i missing something? Any help will be gratefully apprecciated, Best regards

    Read the article

  • LACP : Cisco ASA 5515 & Switch ProCurve 2920

    - by user979276
    I've two ASAs 5515 connected in failover Active/Stand by (on Gi0/5) My two ASAs are connected to two Switch ProCurve 2920 to have HA if something happens. So I plug something like that (don't pay attention to the arrows) : So one the ASA, I created a Port-Channel like that : interface GigabitEthernet0/0 nameif outside security-level 0 ip address 192.168.1.3 255.255.255.0 standby 192.168.1.4 ! interface GigabitEthernet0/1 speed 1000 duplex full channel-group 1 mode passive no nameif no security-level no ip address ! interface GigabitEthernet0/2 speed 1000 duplex full channel-group 1 mode passive no nameif no security-level no ip address ! interface Port-channel1.1 vlan 1 nameif inside security-level 100 ip address 192.168.8.1 255.255.255.0 standby 192.168.8.2 ! interface Port-channel1.10 vlan 10 nameif guest security-level 50 ip address 172.16.100.2 255.255.255.224 standby 172.16.100.3 ! interface Port-channel1.16 vlan 16 nameif dmz security-level 50 ip address 192.168.16.1 255.255.255.0 standby 192.168.16.2 On the switch, I created a trunk LACP capable with the port 1 and 2 on each switch, force the speed to 1000 and put the port un full duplex mode. BUT this is not working... I tried many things and I can't make it work. In this configuration, I can't ping anything between my ASA and my Switch (or any object connected). Here what I get on my ASA : Channel group 1 LACP port Admin Oper Port Port Port Flags State Priority Key Key Number State ----------------------------------------------------------------------------- Gi0/2 SP not-bndl 32768 0x1 0x1 0x3 0xc Gi0/1 FP not-bndl 32768 0x1 0x1 0x2 0x6 And on the Switchs : PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ----- ------- ----- ------ ------- ------ 1 Active trk1 Broken Yes Failure 2 Active trk1 Broken Yes Failure If I change the Cisco interface to LACP mode On, I can ping the switch from the ASA but nothing other objects conneted on the switch. If I look at the statut of LACP on the switch I see this : PORT LACP TRUNK PORT LACP LACP NUMB ENABLED GROUP STATUS PARTNER STATUS ----- ------- ----- ------ ------- ------ 1 Active trk1 Up No Success 2 Active trk1 Up No Success I don't have any clue on what's going on so If someone have any idea and help me on this, it would be great ! Feel free to ask me anything if you need any more information ! Thanks a lot !

    Read the article

  • IPv6 routing to another interface

    - by Robert
    I'm trying to get an IPv6 enabled router to forward data from one interface to the other and I'm having issues. When following this example (http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080ba6106.shtml) I am able to get full connectivity between all 3 routers in my simulator. However when I try to use only 1 router; I can't get connectivity to the other interfacs on the same router. My PC is directly attached to FA 0/1 and it can ping the router's interface. However it can not ping any other interface on the router(which unless I'm missing something it should be able to do). The router on the other hand can ping everything. I thought static routes might help; but the router already has routes for everything. I'm thinking the packet should come in; router looks up the destination in it's ipv6 routing table and then realizes it's for itself, and should respond. I thought maybe it couldn't respond directly; so I tried pinging a device like 2001:0000:0000:1000::2, but i don't get a response. I'm running on IOS 12.4. I'm missing something(hopefully simple), but I just can't see what it is. With only 1 router; how do I enable my PC to talk to the other subnets? Thank you in advance, Robert Topology: R1 FA 0/0: 2001:0000:0000:0000::1/52 FA 0/1: 2001:0000:0000:1000::1/52 FA 1/0: 2001:0000:0000:2000::1/52 Loopback 0: 2001:0000:0000:3000::1/52 PC: 2001:0000:0000:2000::2/52 PC plugs directly into FA 1/0 on the router. --- Configuration --- ipv6 cef ipv6 unicast routing interface Loopback0 no ip address ipv6 address 2001:0000:0000:3000::1/52 ipv6 enable ! interface FastEthernet0/0 no ip address duplex auto speed auto ipv6 address 2001:0000:0000::1/52 ipv6 enable ! interface FastEthernet0/1 no ip address duplex auto speed auto ipv6 address 2001:0000:0000:1000::1/52 ipv6 enable ! interface FastEthernet1/0 no ip address duplex auto speed auto ipv6 address 2001:0000:0000:2000::1/52 ipv6 enable --- end of config --- --- routing table --- IPV6Lab#show ipv6 route IPv6 Routing Table - 10 entries Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP U - Per-user Static route I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2 ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2 C 2001:0000:0000::/52 [0/0] via ::, FastEthernet0/0 L 2001:0000:0000::1/128 [0/0] via ::, FastEthernet0/0 C 2001:0000:0000:1000::/52 [0/0] via ::, FastEthernet0/1 L 2001:0000:0000:1000::1/128 [0/0] via ::, FastEthernet0/1 C 2001:0000:0000:2000::/52 [0/0] via ::, FastEthernet1/0 L 2001:0000:0000:2000::1/128 [0/0] via ::, FastEthernet1/0 C 2001:0000:0000:3000::/52 [0/0] via ::, Loopback0 L 2001:0000:0000:3000::1/128 [0/0] via ::, Loopback0 L FE80::/10 [0/0] via ::, Null0 L FF00::/8 [0/0] via ::, Null0 --- end of routing table ---

    Read the article

  • Cisco redundancy modes

    - by user974896
    I am using a Cisco 6500 series with an SSO redundancy configuration. The show redundancy output is as follows: Hardware Mode = Duplex Configured Redundancy Mode = sso Operating Redundancy Mode = rpr Maintenance Mode = Disabled Communications = Up I would assume the device is operating in RPR mode although SSO is configured. What could cause this? Shouldn't the operating mode be SSO? EDIT (show redundancy states): my state = 13 -ACTIVE peer state = 4 -STANDBY COLD Mode = Duplex Unit = Primary Unit ID = 5 Redundancy Mode (Operational) = rpr Redundancy Mode (Configured) = sso Redundancy State = rpr Split Mode = Disabled Manual Swact = Enabled Communications = Up client count = 60 client_notification_TMR = 30000 milliseconds keep_alive TMR = 9000 milliseconds keep_alive count = 1 keep_alive threshold = 18 RF debug mask = 0x0

    Read the article

  • Anything to share a printer from 32-bit to 64-bit Windows?

    - by marklam
    I've got a printer which only has 32-bit drivers, so it's installed on a 32-bit machine (XP). I need it to appear as a printer (with duplex control etc) on a 64-bit machine (Vista). I can't just share it using Windows printer sharing because the 64-bit client requires drivers to connect to it. There's no 64-bit driver for a similar printer that works (using the new port named \\server\printername). I've tried the ghostscript approach but that doesn't seem to help with the duplex control etc. Printeranywhere doesn't support 64-bit OS yet. Is there another way to do this?

    Read the article

  • How do I manage the technical debate over WCF vs. Web API?

    - by Saeed Neamati
    I'm managing a team of like 15 developers now, and we are stuck at a point on choosing the technology, where the team is broken into two completely opposite teams, debating over usage of WCF vs. Web API. Team A which supports usage of Web API, brings forward these reasons: Web API is just the modern way of writing services (Wikipedia) WCF is an overhead for HTTP. It's a solution for TCP, and Net Pipes, and other protocols WCF models are not POCO, because of [DataContract] & [DataMember] and those attributes SOAP is not as readable and handy as JSON SOAP is an overhead for network compared to JSON (transport over HTTP) No method overloading Team B which supports the usage of WCF, says: WCF supports multiple protocols (via configuration) WCF supports distributed transactions Many good examples and success stories exist for WCF (while Web API is still young) Duplex is excellent for two-way communication This debate is continuing, and I don't know what to do now. Personally, I think that we should use a tool only for its right place of usage. In other words, we'd better use Web API, if we want to expose a service over HTTP, but use WCF when it comes to TCP and Duplex. By searching the Internet, we can't get to a solid result. Many posts exist for supporting WCF, but on the contrary we also find people complaint about it. I know that the nature of this question might sound arguable, but we need some good hints to decide. We're stuck at a point where choosing a technology by chance might make us regret it later. We want to choose with open eyes. Our usage would be mostly for web, and we would expose our services over HTTP. In some cases (say 5 to 10 percent) we might need distributed transactions though. What should I do now? How do I manage this debate in a constructive way?

    Read the article

  • Unable To Get Sound Working to External Speaker on HP TouchSmart 320 on 11.04 or 11.10

    - by Schof
    This is an HP TouchSmart 320, model number 320-1200m. I'm using Ubuntu 11.04. Hardware information: root@hp320:/home/mpower# aplay -l **** List of PLAYBACK Hardware Devices **** card 0: Generic [HD-Audio Generic], device 0: STAC92xx Analog [STAC92xx Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 root@hp320:~$ cat /proc/asound/card0/codec#0 | grep Codec Codec: IDT 92HD91BXX Sound to headphone jack works properly, but sound to built-in speakers does not work. I have installed Windows, and with Windows 7 installed, all audio hardware works properly, so this isn't a hardware fault. I've looked at https://help.ubuntu.com/community/HdaIntelSoundHowto and have been unable to find my card in http://www.kernel.org/doc/Documentation/sound/alsa/HD-Audio-Models.txt . I have tried adding almost every conceivable model in the line "options snd-hda-intel model=MODEL" line I added to /etc/modprobe.d/alsa-base.conf. Update 2011-11-09 2:31 PM PST: I've gone to Control Center - Sound Preferences to attempt settings that make sound work. The "Hardware" tab shows one device: "Internal Audio 1 Output / 1 Input Analog Stereo Duplex." There are two output profiles listed in the selection box at the bottom of the tag: Analog Stereo Duplex and Analog Stereo Output. Neither cause sound to emit from the speakers. I've also run alsamixer on the command-line and ensured that everything is set to maximum and nothing is muted. Update 2011-11-09 5:15 PM PST: I've replicated the exact same symptoms in 11.10. Update 2011-11-10 11:31 AM PST: I've filed a bug in launchpad: https://launchpad.net/ubuntu/+source/alsa-driver/+bug/888703

    Read the article

  • Dell inspiron not finding Vodafone router

    - by Jeggy
    I have a "Dell inspiron 1564" and ubuntu doesn't find my friends router it works great at home, he has a vodafone router jeggy@jeggy-XPS:~$ sudo lshw -C network *-network description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: eth1 version: 01 serial: 78:e4:00:2a:d1:eb width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:17 memory:f0200000-f0203fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:05:00.0 logical name: eth0 version: 02 serial: b8:ac:6f:67:32:52 size: 10Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=N/A latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:3000(size=256) memory:f0410000-f0410fff memory:f0400000-f040ffff memory:f0420000-f043ffff *-network description: Ethernet interface physical id: 4 logical name: ham0 serial: 7a:79:05:ff:3e:ec size: 10Mbit/s capabilities: ethernet physical configuration: autonegotiation=off broadcast=yes driver=tun driverversion=1.6 duplex=full firmware=N/A ip=5.255.62.236 link=yes multicast=yes port=twisted pair speed=10Mbit/s

    Read the article

  • Equivalent of Windows 7 Winkey+Left / Winkey+Right for Window Tiling in OSX

    - by Koobz
    Windows 7 has a neat feature where the Windows Key in conjunction with the arrow keys tiles the active window. Windows key + left arrow moves it to the left half, windows key + right arrow moves your window to the right half of your monitor. Is there an equivalent to this functionality in OS X? Can anyone suggest some alternative metaphors by which to manage my windows? I find that OSX windows tend to be a bit more scatterbrained than their windows counterparts.

    Read the article

  • Browser resizing when the monitor turns on/off?

    - by Jason
    The last week or so I have noticed an odd thing. When I turn on my monitor, my browser windows are all half the size they were when I turned it off. Sometimes when I turn it on the taskbar is even half way up the screen for a few moments, as if turning the monitor on and off was forcing it to change the resolution. I use firefox, running windows 7.

    Read the article

  • tile a window with a hotkey on Ubuntu

    - by Eli Bendersky
    On Windows I use an AutoHotKey script to tile the active window to the left half of the screen, the right half, or a few other options. Does Ubuntu/Gnome have a program that would allow me to do that? If not, do you have an idea how to create this programmatically, or at least can point me to a resource?

    Read the article

  • Combining videos and recording sound over them

    - by Javier Badia
    This is the idea: I want to have a video where I appear twice. With pictures this is easy: you take two pictures of yourself without moving the camera, once in each corner of the room, and then combine half and half with MS Paint. What free Windows program can do this with videos? Also, I later want to record some more sound over it. Will that same program allow me to do that, or do I need something else?

    Read the article

< Previous Page | 5 6 7 8 9 10 11 12 13 14 15 16  | Next Page >