Search Results

Search found 11107 results on 445 pages for 'drive bay'.

Page 91/445 | < Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >

• Degraded RAID5 and no md superblock on one of remaining drive

  - by ark1214

  This is actually on a QNAP TS-509 NAS. The RAID is basically a Linux RAID. The NAS was configured with RAID 5 with 5 drives (/md0 with /dev/sd[abcde]3). At some point, /dev/sde failed and drive was replaced. While rebuilding (and not completed), the NAS rebooted itself and /dev/sdc dropped out of the array. Now the array can't start because essentially 2 drives have dropped out. I disconnected /dev/sde and hoped that /md0 can resume in degraded mode, but no luck.. Further investigation shows that /dev/sdc3 has no md superblock. The data should be good since the array was unable to assemble after /dev/sdc dropped off. All the searches I done showed how to reassemble the array assuming 1 bad drive. But I think I just need to restore the superblock on /dev/sdc3 and that should bring the array up to a degraded mode which will allow me to backup data and then proceed with rebuilding with adding /dev/sde. Any help would be greatly appreciated. mdstat does not show /dev/md0 # cat /proc/mdstat Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4] [multipath] md5 : active raid1 sdd2[2](S) sdc2[3](S) sdb2[1] sda2[0] 530048 blocks [2/2] [UU] md13 : active raid1 sdd4[3] sdc4[2] sdb4[1] sda4[0] 458880 blocks [5/4] [UUUU_] bitmap: 40/57 pages [160KB], 4KB chunk md9 : active raid1 sdd1[3] sdc1[2] sdb1[1] sda1[0] 530048 blocks [5/4] [UUUU_] bitmap: 33/65 pages [132KB], 4KB chunk mdadm show /dev/md0 is still there # mdadm --examine --scan ARRAY /dev/md9 level=raid1 num-devices=5 UUID=271bf0f7:faf1f2c2:967631a4:3c0fa888 ARRAY /dev/md5 level=raid1 num-devices=2 UUID=0d75de26:0759d153:5524b8ea:86a3ee0d spares=2 ARRAY /dev/md0 level=raid5 num-devices=5 UUID=ce3e369b:4ff9ddd2:3639798a:e3889841 ARRAY /dev/md13 level=raid1 num-devices=5 UUID=7384c159:ea48a152:a1cdc8f2:c8d79a9c With /dev/sde removed, here is the mdadm examine output showing sdc3 has no md superblock # mdadm --examine /dev/sda3 /dev/sda3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff0e - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 0 8 3 0 active sync /dev/sda3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed [~] # mdadm --examine /dev/sdb3 /dev/sdb3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff20 - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 1 8 19 1 active sync /dev/sdb3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed [~] # mdadm --examine /dev/sdc3 mdadm: No md superblock detected on /dev/sdc3. [~] # mdadm --examine /dev/sdd3 /dev/sdd3: Magic : a92b4efc Version : 00.90.00 UUID : ce3e369b:4ff9ddd2:3639798a:e3889841 Creation Time : Sat Dec 8 15:01:19 2012 Raid Level : raid5 Used Dev Size : 1463569600 (1395.77 GiB 1498.70 GB) Array Size : 5854278400 (5583.08 GiB 5994.78 GB) Raid Devices : 5 Total Devices : 4 Preferred Minor : 0 Update Time : Sat Dec 8 15:06:17 2012 State : active Active Devices : 4 Working Devices : 4 Failed Devices : 1 Spare Devices : 0 Checksum : d9e9ff44 - correct Events : 0.394 Layout : left-symmetric Chunk Size : 64K Number Major Minor RaidDevice State this 3 8 51 3 active sync /dev/sdd3 0 0 8 3 0 active sync /dev/sda3 1 1 8 19 1 active sync /dev/sdb3 2 2 8 35 2 active sync /dev/sdc3 3 3 8 51 3 active sync /dev/sdd3 4 4 0 0 4 faulty removed fdisk output shows /dev/sdc3 partition is still there. [~] # fdisk -l Disk /dev/sdx: 128 MB, 128057344 bytes 8 heads, 32 sectors/track, 977 cylinders Units = cylinders of 256 * 512 = 131072 bytes Device Boot Start End Blocks Id System /dev/sdx1 1 8 1008 83 Linux /dev/sdx2 9 440 55296 83 Linux /dev/sdx3 441 872 55296 83 Linux /dev/sdx4 873 977 13440 5 Extended /dev/sdx5 873 913 5232 83 Linux /dev/sdx6 914 977 8176 83 Linux Disk /dev/sda: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 66 530113+ 83 Linux /dev/sda2 67 132 530145 82 Linux swap / Solaris /dev/sda3 133 182338 1463569695 83 Linux /dev/sda4 182339 182400 498015 83 Linux Disk /dev/sda4: 469 MB, 469893120 bytes 2 heads, 4 sectors/track, 114720 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/sda4 doesn't contain a valid partition table Disk /dev/sdb: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdb1 * 1 66 530113+ 83 Linux /dev/sdb2 67 132 530145 82 Linux swap / Solaris /dev/sdb3 133 182338 1463569695 83 Linux /dev/sdb4 182339 182400 498015 83 Linux Disk /dev/sdc: 1500.3 GB, 1500301910016 bytes 255 heads, 63 sectors/track, 182401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdc1 1 66 530125 83 Linux /dev/sdc2 67 132 530142 83 Linux /dev/sdc3 133 182338 1463569693 83 Linux /dev/sdc4 182339 182400 498012 83 Linux Disk /dev/sdd: 2000.3 GB, 2000398934016 bytes 255 heads, 63 sectors/track, 243201 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sdd1 1 66 530125 83 Linux /dev/sdd2 67 132 530142 83 Linux /dev/sdd3 133 243138 1951945693 83 Linux /dev/sdd4 243139 243200 498012 83 Linux Disk /dev/md9: 542 MB, 542769152 bytes 2 heads, 4 sectors/track, 132512 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md9 doesn't contain a valid partition table Disk /dev/md5: 542 MB, 542769152 bytes 2 heads, 4 sectors/track, 132512 cylinders Units = cylinders of 8 * 512 = 4096 bytes Disk /dev/md5 doesn't contain a valid partition table

  Read the article

• Wear and tear on server hard drive from filesystem polling by PHP script

  - by jackie

  So I'm working on a discussion platform, and various clients will visit http://host/thread.php, which will render the discussion thread to date in addition to a form to submit a new post. When a new post is submitted, I would like all of the other clients with browser windows open to have it appear in near-real-time. One of the constraints of my script is that it may not use a DBMS and it must stay in the filesystem. Additionally, I can't use any PECL/PEAR extensions like inotify or anything like that for IPC. The flow will look like this: Client A requests thread.php and the thread is so far empty, but nonetheless it opens a Server-Side Event at eventPusher.php. Client B does the same. Client A fills out a post in the form and and submits (POSTs) it to subHandler.php. ??? (subHandler stores the new submission into the main thread storefile which gets read from when a fresh, new client requests thread.php, in addition to somehow signalling to the continually-running eventPusher event-source that a new comment was posted and that it should echo the event-json to the client. How, exactly, it will send this signal I'm yet unsure of, but there are a few options that I've thought of -- this is the crux of the question, so see below for more clarification) eventPusher.php happily pushes the new event to the client and it shows up soon after it was originally submitted on all clients who have the page open's screens. Now for the #4 missing-link mystery-step, I see a few problems. I mean, either way, eventPusher is gonna be doing a while loop of some sort -- it's gonna be polling something, I think that much is clear. (If that's a bad assumption please do let me know.) Now, the simplest way would be subHandler gets invoked on the form submission, writes it to the main store in addition to newComments.xml, then exits without doing anything else. Then eventPusher checks in newComments.xml every X seconds (by the way, what would be a reasonable time interval here?) and if it finds something then it emits an event to the client. Now, my fear with this is that the server's hard drive will have to constantly start spinning up. Maybe this isn't the case, perhaps it would just get cached in RAM and the linux kernel would take care of this transparently such that filesystem access doesn't actually engage the device because the kernel knows that that particular file hasn't changed since last read. * idea #2: I have no idea how to go about this, but perhaps there is a variable scope that gets stored in general RAM on the system which can be read by any process. Like if we mega-exported a bash variable so that $new_post is normally false but it gets toggled to true by subHandler, and then back to flase once it's pushed to the client. I doubt there's such a variable scope in PHP directly, but I struggle with the concept of variable scope, I just can't seem to understand it no matter what I read on it. * idea #3: eventPusher queries ps in its whileloop for another instance of itself. If there's not another eventPusher active then it's highly unlikely that new comments will be getting submitted. It's okay if this only works =90% of the time, it doesn't need to be completely foolproof. * idea #4: eventPusher queries DMESG to see if that file's been written to recently. So to sum everything up, I need to have inter-php-script-communication in near-real-time that will work on a standard mod_php shared hosting setup without any elevated privileges, PHP addon modules, or other system adjustments that can't be done from the PHP script itself at runtime. With*out* spinning up the drive more than a few times. No SQL servers either. Apologies if my english isn't the best, I'm still trying to improve on it.

  Read the article

• Systems Solutions at COLLABORATE12

  - by ferhat

  Want to connect with fellow Oracle users and learn more about how to maximize your Oracle software environments with Oracle Systems?   Pack your bags for Las Vegas!   COLLABORATE 12  is right around the corner! COLLABORATE 12 Conference will be held at the Mandalay Bay in Las Vegas, NV 22-26 April, 2012. This is an event designed and delivered by users just like you with sessions, interactive panel discussions and hands-on learning opportunities packed with first-hand experiences, case studies and practical “how-to” content.. This year’s event includes a number of educational sessions and demos for users interested in learning from the experts how to use Oracle Optimized Solutions to get the most out of their Oracle Technology and Application software. Oracle Optimized Solutions are proven blueprints that eliminate integration guesswork by combing best in class hardware and software components to deliver complete system architectures that are fully tested, and include documented best practices that reduce integration risks and deliver better application performance.  And because they are highly flexible by design,  Oracle Optimized Solutions   can be implemented as an end-to-end solution or easily adapted into existing environments. Follow Oracle Infrared at Twitter, Facebook, Google+, and LinkedIn  to catch the latest news, developments, announcements, and inside views from  Oracle Optimized Solutions. Please come by our Exhibition Booth #1273 to see the demos and meet 1-1 with the experts behind a number of  Oracle Optimized Solutions  including those for JD Edwards EnterpriseOne, E-Business Suite, PeopleSoft HCM, Oracle WebCenter, and Oracle Database.  Exhibitor Showcase Booth #1273 DAY TIME TITLE Monday  April 23 6:00 pm - 8:00 pm Welcome Reception in the Exhibitor Showcase Tuesday  April 24 10:15 am - 4:00 pm Exhibitor Showcase Open 1:00 pm - 2:00 pm Dedicated Exhibitor Showcase Time 5:30 pm - 7:00 pm Exhibitor Showcase Happy Hour Wednesday  April 25 10:30 am - 3:00 pm Exhibitor Showcase Open 2:15 pm -3:00 pm Afternoon Break in Exhibitor Showcase  There are also a number of deep dive, educational sessions covering deployment best practices using Oracle’s engineered systems and best-in-class hardware, operating system and virtualization technologies.  Education Sessions DAY TIME TITLE LOCATION Monday  April 23 9:45 am - 10:45 am Architecting and Implementing Backup and Recovery Solutions Surf E Tuesday  April 24 2:00 pm – 3:00 pm Oracle's High Performance Systems for JD Edwards EnterpriseOne Mandalay Bay GH 4:30 pm - 5:30 pm Virtualization Boot Camp: What's New with Oracle VM Server for x86 Mandalay Bay C 9:30 am - 10:30 am Oracle on Oracle VM - Expert Panel Mandalay Bay L Wednesday  April 25 9:30 am - 10:30 am Cloud Computing Directions: Part II Understanding Oracle's Cloud Directions South Seas E  And don’t forget the keynotes and software roadmap sessions! Keynotes and Roadmap Sessions DAY TIME TITLE LOCATION Sunday  April 22 3:20 pm – 4:20 pm Oracle’s Cloud Computing Strategy Breakers B Monday  April 23 11:00 am – 12:00 pm JD Edwards - Vision, Promises and Execution: IT'S THE WAY WE ROLL and Why it Matters! Mandalay Bay A 11:00 am – 12:00 pm PeopleSoft Executive Update and Roadmap Mandalay Bay J 1:15 pm - 2:15 pm Oracle Database - Engineered for Innovation Mandalay Bay L 2:30 pm - 3:30 pm Oracle E-Business Suite Applications Strategy and General Manager Update Mandalay Bay D Tuesday  April 24 9:15 am - 10:15 am IT at Oracle: The Art of IT Transformation to Enable Business Growth Mandalay Bay Ballroom H

  Read the article

• Why can't I browse my D: drive, even if I'm in the Administrators group?

  - by Nic Waller

  My fileserver running Windows Server 2008 has two logical drives; the C: drive contains all of the system and application data, and the D: drive contains all of the business data. There are several shares on the top level of the D: drive that are working fine. However... When logged into the fileserver interactively via Remote Desktop, only the Domain Administrator and local Administrator accounts can browse the D: drive. I set up an account called "Maintenance" and added it to the local Administrators group, but when logged in with this user, I can't browse into the D: drive. The D: drive has the following permissions ACL: Full Access - SYSTEM Full Access - MACHINE\Administrators It won't even let me view the ACL for the E: drive. So I tried taking ownership of the E: drive, then I can read the ACL, and "Effective Permissions" says that I have full access. But I still get this error message. Location is not available D:\ is not accessible. Access is denied. Here's a screenshot proving that I get access denied even when I have Full Access. http://www.getdropbox.com/gallery/2319942/1/errors?h=2bd644

  Read the article

• How to diagnose issue between mobo, RAID, and SSD cache drive? [migrated]

  - by goober

  Background This issue is happening on my custom-built desktop. Relevant specs: Motherboard: ASUS P8Z68-V PRO Utilizing Intel RST technology (application that uses unused SSD as cache) Processor: Intel core i7-2600k (not overclocked) HDDs: RAID1 of 2x Seagate Barracuda 1TB (ST31000524AS) (RAID performed via z68 chipset) Machine has run fine for ~1 year with no issues, and has been well-maintained (dust, etc.) What Happened Random Freezing issues -- intermittent Looked at the RST application screen to see that the acceleration cache was listed as "unavailable" -- recommended that I power down and reconnect the drive. Reconnected the drive to no avail. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Now, the freeze happens whenever loading something particularly data-driven (a video, a game, etc.) Steps Attempted Reconnected the drive to no avail. Updated Intel RST software to v. 11.6.0.1030 to see if that made a difference. Attempted to move the drive to another SATA port. Acceleration option disappeared from RST software. Connected the drive as its own volume. Formatted it, ran disk check errors -- all seems fine. Reconnected the drive and selected it again as the cache drive. Now, what happens when there is a freeze: Machine freezes I am unable to perform any command Screen then goes black I hit the reset button During boot, all drives show as "Disabled" and I am told no volume can be found I then hit the reset button (or power off/on) again. Either the next time (or sometimes after repeating this once more), the metadata cache is reconstructed and the system boots fine, showing the SSD as a cache. Question I believe this is an issue with the SSD itself, but how can I be sure since connecting it separately appeared to show no problems? I want to make sure it's not an issue with the motherboard, SATA ports, etc.

  Read the article

• TEMP_PART01 and C drive

  - by SmartLemon

  So we have a Samsung series 9 laptop and it has a 128 GB solid state drive, the problem we are having with it is that it has 4 partitions, one that's 100MB (who knows what for), one thats 40 GB (Primary Windows partition), 60 GB partition (TEMP_PART01) and a microsoft office one. The primary windows partition only has less than, 30 MB left, we want to increase this space, I know that I could just move everything to temp_part01 but we are not quite sure on it. What we are thinking of doing is deleting this partition all together and extending the windows volume. The problem is that the extra partition has 55.7 remaining out of 59.7 GB, which means there is something on it, but it shows up with nothing when we go into it, when we change the settings to show hidden files, but still nothing, I then used CMD to list all the files using dir d: and still no files. So would it be safe to delete it and extend the windows volume? Or what should I do? Here's a screen shot:

  Read the article

• OS X - Mount .dmg image into a virtual DVD drive without Toast Titanium

  - by Max

  Hi, Toast Titanium 10 offers a way of mounting an image into a virtual DVD drive so that it is viewed as being a separate physical drive by other applications. I was wondering if there was a way of achieving the same result using the built-in OS X tools (whether GUI or command line), as I am aware it has many of such built in. Thanks in advance!

  Read the article

• SQL Server Rights to backup drive

  - by Sam

  I'm trying to copy a backup I've made from one server to another using either an SSIS or Powershell step in a job. I've run into the same error on both systems when running the step under the sql agent. I receive errors that the path does not exist. I've tried granting the agent rights to e:\backups, where the file is located, but it still doesn't work. When I use a proxy for the step, it works fine. Can anyone help me with what permissions to grant to sqlagent? Rights look to have been granted to MSSQL$Instance1 on the backup drive.

  Read the article

• NAS that supports NZB downloading for around £150 ($220) or less (without hard drive)

  - by Jigs

  I have seen a number of NAS's that are around that price, but I am worried that they may not be able to handle the processing of .rar files (I know that can be quite CPU intensive). Does anyone have any experiences with sabnzbd or hellanzb - or similar on their NAS? In terms of features the main requirement is NZB downloading - I am quite flexible on the other features. Wifi support would be nice, but not essential. Torrent downloading would also be nice. One disk drive would probably be enough. Easy installation of application would be nice... but again I am sure I can follow a tutorial.

  Read the article

• Gigabyte GA-P55A-UD4P won't boot from USB drive with RAID enabled

  - by Daniel Schaffer

  I've got a Windows 7 installation image on my USB hard drive, which is set up to be bootable. I know it works because I've used it on several computers, and it works on the computer I'm trying to install as long as the RAID controller is disabled. However, when I enable the RAID controller and attempt to boot from the USB driver, it hangs for 30-60 seconds and then gives me the "disk boot failure, insert system disk" error like it can't find any OS. Just for laughs, I disabled the RAID controller again and it booted fine. I'm having separate, unrelated issues burning a dvd with the ISO, so I would prefer to get this working.

  Read the article

• How to increase hard drive transfer speed

  - by atif089

  This is my motherboard GA-M61PME-S2 (SATA upto 3.0 Gbps) and This is my Hard Disk Samsung hd502hi Capacity 500 GB Cache 16MB Disks / Heads 1 / 2 Interface SATA 3Gb/s Spindle Speed 5400 RPM Sustained Data Rate OD 100 MB/s Average Seek 8.9 ms Average Latency 5.56 ms Data Transfer Rate 300 MB/sec Weight 470 grams Power: Idle / Seek / R-W / Spin-up 3.9W / 4.8W / 5.1W / ~24W Acoustics (sound power) 2.2 / 2.7 Bel (idle / quiet seek / performance seek) When I copy things from one partition to another they transfer at a maximum of 30 MBps. However the drive supports upto 300 MBps right ? How do I increase the transfer speeds? P.S - Using Windows XP, All partitions are NTFS.

  Read the article

• USB Thumb Drive not recognized in Hyper-V Manager

  - by Vazgen

  I have the free, standalone core Hyper-V Server 2012 running on my physical machine. I set up remote management from my Windows 8 client. When I proceed to create a virtual machine I would like to install the OS from a usb thumb drive but it is not recognized in Hyper-V Manager on my client (when the USB is plugged into the physical server) nor is it recognized in Server Manager under File and Storage Services Volumes Is there a role needed to recognize external usb flash drives? Because I think this standalone version is just core Hyper-V role and that's it... but this is such a basic functionality. Can anybody comment.

  Read the article

• unzip file on small drive

  - by David Oneill

  I have a zip file that contains many files. Each file in the zip file is about 100MB, and is compressed about 10% (IE it is about 90MB in the zip file). The whole zip file is 20GB, and I'm trying to unzip it onto a drive that has only 30GB free. On Windows 7, how can I unzip a zip file on my laptop's harddrive that doesn't have enough space for both the zipped and unzipped copies of the file? IE can I tell windows to remove stuff from the zip file as it is uncompressed?

  Read the article

• Server only powers (but doesn't POST) when IDE drive is powered

  - by Jookia

  So after a thunderstorm last night which did a little damage, a Gigabyte server has decided it's going on power on but not POST. If it is POSTing, it's doing a very bad job at telling me. No beeps, nothing. Power seems to reach the components though. CD Drive opens and closes. So after stripping it back, I've found that the difference between this behaviour and deciding it's not going to power on for more than half a second, is having a power cable plugged in to one of the IDE hard drives. Is this normal, or a sign that the PSU has had it?

  Read the article

• How many hardlinks in a drive?

  - by acidzombie24

  I made a backup of one of my external drives to another. They are both NTFS filesystems. I moved ALL disk contents into a folder called a and right clicked to get file/folder/size count. They are exactly the same. However windows reports J having 1.33gb (backup) and Q: as 521mb. Now I think maybe its because of hardlinks, I must have more on J then Q. How might I figure out how many hardlinks I have in a drive?

  Read the article

• Ultrium 3 tape drive shoe-shining, 3Mb/s: and it's not the cable

  - by mowsala

  I have a HP 960 Ultrium 3 tape drive. Since I got it, (second hand, £90) I've been experiencing shoe-shining. Writing with tar in Linux, I average about 3Mb/s write speed. I've tried replacing both the SCSI card and the cable now, both of which made no difference at all. A curiuos observation I have made is that the write rate is not consistent. Sometimes it will write for over a minute without shoeshining, but more often, just a few seconds. I've also tried several tapes, different source drives, and even writing from Windows Backup, to no avail.

  Read the article

• Formatted a Bootcamped drive as a dynamic disk, now can't boot to either Mac or Windows

  - by Steven H

  I was trying to create an extra partition to get a file from the Windows side of my Macbook Air to the Mac side, and I accidentally made the disk dynamic without realizing it. I am now unable to boot to the Mac side (holding Alt to go into the system manager at startup doesn't even list the Mac partition), and the Windows side blue screens during boot (goes so quickly that it doesn't even get to the error code before restarting). What can I do to fix the issue? I don't know how to make a bootable flash drive that a Mac will recognize, and Disk Utility (via Internet Recovery) couldn't do anything. (cross-posted from apple.stackexchange)

  Read the article

• WebDAV mapped drive asking for username and password

  - by confus3d

  Since we migrated domains we're having problems with mapping a drive using a WebDAV connection in our login script. It's a simple net use x: \\server.domain.com\folder Which used to authenticate automatically (all we needed to do to make this happen was to put the server in the intranet zone in the internet explorer settings). Since the domain migration though, nearly everyone is being prompted for a username and password to connect. Does anyone have any idea how to fix this? Any help much appreciated. The webdav share is on a Windows 2003 server running IIS.

  Read the article

• Using USB drive in Windows and Linux properly

  - by sashkello

  What is the proper way of using a USB hard drive or stick between Linux and Windows? (I'm using Linux Mint 14 and Windows XP on different machines) Should I set it up somehow so that all the files are shared and reused safely between Linux and Windows? The question comes from the recent problem I had. I've created and edited a few folders through Linux and they are not working on Windows now (folder is not accessible. The file or directory is corrupt). While I dealt with that problem, what would be the way of ensuring this doesn't happen again?

  Read the article

• Adding a single 300Gb SCSI drive to poweredge 2850

  - by John Steele

  I have a 2850 setup with 3 146Gb drives, two partitions 1 12GB system with server 2003 sp2 and 1 261Gb Data. I am strapped on disk space on the data partition having to push data around. I wanted to add a 300Gb single drive for lesser critical data, is this possible? Or is it best to add 2 300Gb drives for another RAID 1 configuration? This is my church network and while it is mission critical it is not enterprise so I can take it down for a few hours. Any pointers to documentation or direct help would be greatly appreciated. John

  Read the article

• How to get the drive letter of pendrive

  - by sijith

  Hi, I want to get the drive letter of pendrive or external harddisk connected through USB. Is it possible to get the Drive letter. I am using VC++

  Read the article

• Unable to delete a directory from NTFS drive: "Access is denied"

  - by Evgeny

  I'm running Windows XP Pro x64 SP2. I have a directory on an NTFS drive that was created by a Maven build. A subsequent build attempted to delete this directory and failed. I now get the error "Access is denied" whenever I try to do anything with that directory: change to it, delete it, rename it. This happens both in Windows Explorer and from a command prompt. The properties dialog in Windows Explorer doesn't even contain the Security tab. I created the directory, so I don't think this is truly a permissions issue. I've occasionally had this error happen in the past is well. I believe the error is misleading, but the question is: what is the real problem and how do I fix it?

  Read the article

• USB drive gets infected every time I plug it into my laptop

  - by ashwnacharya

  Whenever I plug in my USB flash drive into my laptop running Windows XP, an AutoRun.inf file gets created inside it. Also a hidden folder called "Cache" which uses the Recycle bin icon gets created. AutoRUn.inf file cannot be opened in Windows. Both the Autorun.inf file and the "Cache" folder cannot be deleted. I opened the AutoRun.inf file using Ubuntu. I saw that it is trying to run a file Cache\TMP983.exe. I ran all anti-spywares, anti-malwares, anti-viruses, USB autorun eaters, but to no avail. How do I fix this?

  Read the article

• Best way to Duplicate a Laptop's Hard Drive One-to-One

  - by Urda

  I have a Lenovo X61 Tablet computer, with a plain SATA drive inside. I have windows 7 and Ubuntu 9.10 dual booting on the computer. I want to back up both of these OS's, and their special partitions (Windows 7 has one, and of course the Linux Swap). I want a one-to-one backup, all of my mission critical data is already backed up, but I would like to get a snapshot, and store it on a larger file server at home for quick recovery. What is the best approach to do this?

  Read the article

• LTO 3 tape drive needing repaired

  - by DO it all Paul

  We have an IBM LTO 3 tape drive that needs repaired and with the £400 price tag i'm having to shop around for quotes. My question is has anyone actually repaired one before and how was in done? The first error LED was showing a 6, then i cleared the mangled tape only for it to start flashing alternate 'o' on the 7 segment display, simliar to a half 8, flashing top to bottom and it would just flash away like that coupled with a flashing amber light. I tried a reset holding the eject button for it to show an 'r' the go back to flashing again as before. I checked the IBM solutions for the codes but this flashing isn't documented at all. Would be great if anyone had any experience in this area. Thank you, Paul

  Read the article

< Previous Page | 87 88 89 90 91 92 93 94 95 96 97 98  | Next Page >