Search Results

Search found 10810 results on 433 pages for 'port forwarding'.

Page 93/433 | < Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >

  • Exchange 2010 Deployment Notes - ISA 2004 Server Issue

    - by BWCA
    An interesting ISA 2004 tidbit … While we were setting up our Exchange 2010 ActiveSync environment, we encountered a problem where we could not successfully telnet over port 443 from one of our ISA 2004 Servers to our Exchange 2010 Client Access Server Array. When we tried to telnet over port 443 from the ISA Server to the Client Access Server Array name, we would get a “Could not open connection to the host on port 443: Connect failed” error message. Also, when we used portqry over port 443 from the ISA Server to the Client Access Server Array name, we would get a “Error opening socket: 10065” and “No route to host” error messages. It was odd because we did not have any problems with using ping or tracert from the ISA Server to the Client Access Server Array and our firewall firewall policy was allowing 443 traffic to pass through. After some troubleshooting, we were able to telnet and use portqry over port 443 successfully if we stopped the Microsoft Firewall service on the ISA 2004 Server.  So, it was strictly a problem with ISA.  Eventually, we were able to isolate the problem to a ISA 2004 Server System Policy setting as shown below (to modify the System Policy, right-click Firewall Policy and click Edit System Policy). Under the Diagnostics Services – HTTP Connectivity verifiers Configuration Group, you need to enable the configuration group under the General tab to resolve the problem.  After we enabled the setting, we no longer had a problem.

    Read the article

  • Monit can't detect MySQL, but I can

    - by Matchu
    Monit is configured to watch MySQL on localhost at port 3306. check process mysqld with pidfile /var/lib/mysql/li175-241.pid start program = "/etc/init.d/mysql start" stop program = "/etc/init.d/mysql stop" if failed port 3306 protocol mysql then restart if 5 restarts within 5 cycles then timeout My application, which is configured to connect to MySQL via localhost:3306, is running just fine and can access the database. I can even use MySQL Query Browser to connect to the database remotely via port 3306. The port is totally open and possible to connect to. Therefore, I'm pretty darn certain that it's running. However, running monit -v reveals that Monit cannot detect MySQL on that port. 'mysqld' failed, cannot open a connection to INET[localhost:3306] via TCP This happens consistently, until Monit decides not to track MySQL anymore, as configured. How can I begin to troubleshoot this issue?

    Read the article

  • Cannot Mount USB 3.0 Hard Disk ?!!

    - by Tenken
    Hi, I have a USB 3.0 external hard disk which I am unable to mount. The entry appears in the "lsusb" command, but I do not exactly understand how to mount it. This is the output for my lsusb command. "ASMedia Technology Inc." is the USB 3.0 device. I would appreciate some help in mounting and accessing the hard disk. This the relevant output of my "lsusb -v" : Bus 009 Device 002: ID 174c:5106 ASMedia Technology Inc. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x174c ASMedia Technology Inc. idProduct 0x5106 bcdDevice 0.01 iManufacturer 2 ASMedia iProduct 3 AS2105 iSerial 1 00000000000000000000 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 32 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xc0 Self Powered MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 8 Mass Storage bInterfaceSubClass 6 SCSI bInterfaceProtocol 80 Bulk (Zip) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 0 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 3.00 bDeviceClass 9 Hub bDeviceSubClass 0 Unused bDeviceProtocol 3 bMaxPacketSize0 9 idVendor 0x1d6b Linux Foundation idProduct 0x0003 3.0 root hub bcdDevice 2.06 iManufacturer 3 Linux 2.6.35-28-generic xhci_hcd iProduct 2 xHCI Host Controller iSerial 1 0000:04:00.0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 25 bNumInterfaces 1 bConfigurationValue 1 iConfiguration 0 bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 9 Hub bInterfaceSubClass 0 Unused bInterfaceProtocol 0 Full speed (or root) hub iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0004 1x 4 bytes bInterval 12 Hub Descriptor: bLength 9 bDescriptorType 41 nNbrPorts 4 wHubCharacteristic 0x0009 Per-port power switching Per-port overcurrent protection TT think time 8 FS bits bPwrOn2PwrGood 10 * 2 milli seconds bHubContrCurrent 0 milli Ampere DeviceRemovable 0x00 PortPwrCtrlMask 0xff Hub Port Status: Port 1: 0000.0100 power Port 2: 0000.0100 power Port 3: 0000.0503 highspeed power enable connect Port 4: 0000.0503 highspeed power enable connect Device Status: 0x0003 Self Powered Remote Wakeup Enabled This is the error given when I try to mount the hard drive: shinso@shinso-IdeaPad:~$ sudo mount /dev/sdb /mnt [sudo] password for shinso: mount: /dev/sdb: unknown device This the output of "dmesg|tail": [30062.774178] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO [30535.800977] usb 9-4: USB disconnect, address 3 [30659.237342] Valid eCryptfs headers not found in file header region or xattr region [30659.237351] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO [31259.268310] Valid eCryptfs headers not found in file header region or xattr region [31259.268313] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO [31860.059058] Valid eCryptfs headers not found in file header region or xattr region [31860.059062] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO [32465.220590] Valid eCryptfs headers not found in file header region or xattr region [32465.220593] Either the lower file is not in a valid eCryptfs format, or the key could not be retrieved. Plaintext passthrough mode is not enabled; returning -EIO I am using Ubuntu 10.10 (64 bit). Any help is appreciated.

    Read the article

  • Is scanning the ports considered harmful?

    - by Manoj R
    If any application is scanning the ports of other machines, to find out whether any particular service/application is running, will it be considered harmful? Is this treated as hacking? How else can one find out on which port the desired application is running (without the user input)? Let's say I only know the port range in which the other application could be running, but not the exact port. In this case, my application ping each of the port in range to check whether the other application is listening on it, using already defined protocol. Is this a normal design? Or is this considered harmful for the security?

    Read the article

  • Cursor running wild, then crashes on an Asus G73sw

    - by Yarchmon
    The cursor sometimes goes wild, I get random clicks, the windows are resizing, the cursor disappears. In the worst case, clicks and keyboards are disabled. I've tried the solution given on doc.ubuntu-fr.org and add tu grub : i8042.nomux=1 i8042.reset=1 in GRUB_CMDLINE_LINUX_DEFAULT But it didn't work What can I do ? Graphic card : Geforce GTX460M. Ubuntu : 11.10 (64 bits). Laptop Asus G73sw Interface : Unity (since 11.10) - didn't get this problem with Gnome before. Complement: when a window is resizing, it gets drag-boxes at every corner, center of sides and center of the window. It looks like my touchpad sends random info, or like a "ghost" touchscreen. lspci result : 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09) 00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04) 00:1a.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05) 00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05) 00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5) 00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5) 00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5) 00:1c.5 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 (rev b5) 00:1d.0 USB Controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05) 00:1f.0 ISA bridge: Intel Corporation HM65 Express Chipset Family LPC Controller (rev 05) 00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05) 00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05) 01:00.0 VGA compatible controller: nVidia Corporation GF106 [GeForce GTX 460M] (rev a1) 01:00.1 Audio device: nVidia Corporation GF106 High Definition Audio Controller (rev a1) 03:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 04:00.0 USB Controller: Fresco Logic FL1000G USB 3.0 Host Controller (rev 04) 05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06) Edit 01-09-12: Tried on Ubuntu 2D: the behavior is different: it's like i'm randomly clicking on the workspace switcher icon. In the worst case, it can happen several times in a minute.

    Read the article

  • Choppy USB mice on just one of USB ports

    - by user20532
    I've got Lenovo b560 laptop with latest, properly updated Kubuntu on it (11.04 natty, kernel 2.6.38-8-generic). It has three USB2.0 ports onboard. I usually plug a mouse into one of them (I've got 3 different mice - in office, at home and for when on the go). Sometimes, usually after laptop awakening from sleep, the mouse still works but cursor movements are choppy, as if the processor was extremely loaded (it's usually not). I found that if I re-plug the mouse cord into the other USB port, it works just fine. If I plug it back to problematic port, it is still choppy and remains choppy until next boot. Of course I want my mice to always work fine. Problem is: I cannot reproduce this behavior for sure, it happens sporadically but regularly. I use different USB ports (problem has ever happened on each of them since), I use different mice (each has failed me this way at least once), I cannot generally find what exactly is going wrong and why plugging to different port fixes the mouse instantly. So I'd like to hear at least clues where to look at, what to try to identify my problem. A bit of update: while beginning this post, I had the issue once again. I have just replugged the mouse back to problematic port and it is not recognized at all. On the other port it works smoothly.

    Read the article

  • Would a typical corporate firewall block a Java applet having the following behaviour

    - by auser
    I'm thinking of developing a proxy-like program to forward ports on a remote PC to a local PC (for example SSH). Assume that both local and remote PCs are running behind typical firewalls (i.e. consumer broadband router firewall, Windows firewall or corporate firewalls). The program will be a Java program which the user will run on both the remote and local PC. The remote client will periodically poll a central server to determine whether there are pending client connections. A session could be initiated as follows: The local client contacts the central server and request the current connection details for a specific remote client. The central server responds with the remote server's last received IP address and port. The next time the remote server polls the central server, the client's IP address and port are returned. The remote server initiates a connection to the local client using the IP address and port returned by the central server and listens for a response on a random port. The remote server will pass the value of the port it's listening on to central server. Goto 1, if client fails to connect to server. Would this work or will a typical firewall block the interactions.

    Read the article

  • Bizarre SSH Problem - It won't even start

    - by thallium85
    I recently got Ubuntu 12.04 Precise, got it up and running with some MediaWiki software, static IP on the box and router and was able to access the main page even from a cell phone. Everything seemed great... Then I wanted to finally get rid of the monitor and keyboard and login remotely via SSH. I installed openssh-server, let everything point to port 22 for a test run and installed putty on my Windows XP machine. I got a connection refused. Went back and started checking the Ubuntu install itself... (I'm under root from this point on) $ sudo -s $ service ssh status ssh stop/waiting $ service ssh start ssh start/running, process 2212 $ service ssh status ssh stop/waiting Apparently ssh has stopped or is waiting for something.... $ ssh localhost ssh: connect to host localhost port 22: Connection refused I can't even connect to myself... I checked ufw (firewall) to see if port 22 is doing alright... $ sudo ufw status Status: active To Action From 22 ALLOW Anywhere 22/tcp ALLOW Anywhere 22 ALLOW Anywhere (v6) 22/tcp ALLOW Anywhere (v6) sshd_config shows only Port 22 Is ssh not using the right IP address at all? I just don't get what I did wrong here. When this is up and running I will def change the port number, but for now, I don't want to mess with the default install too much until a test run with putty is successful. Edit: Here are my sshd_config file and my ssh_config file. The command /usr/sbin/sshd -p 22 -D -d -e returns: /etc/ssh/sshd_config line 159: Subsystem 'sftp' already defined. Edit: @phoibus moving the sshd_config file and reinstalling did the trick! service ssh status the above command shows that ssh is now running and I am now able to log in from my windows xp computer remotely via putty. Thanks so much! I can now use my monitor for other things!

    Read the article

  • My LAN USB NIC is not working in ubuntu 11.10?

    - by Gaurav_Java
    Today i start my system its seems that my LAN port is not working . so i buy one USB to LAN adapter and i plug in ubuntu system its doen't connect automatically .when i check result lsusb its shows me that there is one DM9601 Ethernet adapter is connected when i click on network information in panel its shows me that there is something " wired NEtwork (Broadcom NetLink BCM5784M gigabit Ethernet PCIe) I think want some driver for that .i don't have any idea how it can be used ? here output of sudo lspci -nn *00:00.0 Host bridge [0600]: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub [8086:2a40] (rev 07) 00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07) 00:02.1 Display controller [0380]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a43] (rev 07) 00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 [8086:2937] (rev 03) 00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 [8086:2938] (rev 03) 00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 [8086:293c] (rev 03) 00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio Controller [8086:293e] (rev 03) 00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 [8086:2940] (rev 03) 00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 [8086:2942] (rev 03) 00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 [8086:2944] (rev 03) 00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express Port 5 [8086:2948] (rev 03) 00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 [8086:2934] (rev 03) 00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 [8086:2935] (rev 03) 00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 [8086:2936] (rev 03) 00:1d.3 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 [8086:2939] (rev 03) 00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 [8086:293a] (rev 03) 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 93) 00:1f.0 ISA bridge [0601]: Intel Corporation ICH9M LPC Interface Controller [8086:2919] (rev 03) 00:1f.2 SATA controller [0106]: Intel Corporation ICH9M/M-E SATA AHCI Controller [8086:2929] (rev 03) 00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller [8086:2930] (rev 03) 02:00.0 Ethernet controller [0200]: Broadcom Corporation NetLink BCM5784M Gigabit Ethernet PCIe [14e4:1698] (rev 10) 04:00.0 Network controller [0280]: Intel Corporation WiFi Link 5100 [8086:4232]* sudo lshw -class network *-network description: Ethernet interface product: NetLink BCM5784M Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 10 serial: 00:1f:16:9a:56:98 capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.119 firmware=sb v2.19 latency=0 link=no multicast=yes port=twisted pair resources: irq:47 memory:f4500000-f450ffff *-network DISABLED description: Wireless interface product: WiFi Link 5100 vendor: Intel Corporation physical id: 0 bus info: pci@0000:04:00.0 logical name: wlan0 version: 00 serial: 00:22:fa:09:02:00 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-17-generic firmware=8.83.5.1 build 33692 latency=0 link=no multicast=yes wireless=IEEE 802.11abgn resources: irq:46 memory:f4600000-f4601fff *-network description: Ethernet interface physical id: 4 logical name: eth1 serial: 00:60:6e:00:f1:7d size: 100Mbit/s capacity: 100Mbit/s capabilities: ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=dm9601 driverversion=22-Aug-2005 duplex=full firmware=Davicom DM9601 USB Ethernet ip=192.168.1.34 link=yes multicast=yes port=MII speed=100Mbit/s I am using Wimax internet connection which i have to connect from browser . at that time my system is not showing that i am connected to any wired connection. but when i connect internet from other system after getting conneted to internet . when i plug again my USB LAN then its shows that you are conneted to wired connetion. here is screenshot for conneting wimax from browser after connecting to internet network connection shows

    Read the article

  • My father wants to learn PHP-MySQL to port his application. What I should do to help?

    - by adijiwa
    My father is a doctor/physician. About 15 years ago he started writing an application to handle his patient's medical records in his clinic at home. The app has the ability to input patient's medical records (obviously), search patients by some criteria, manage medicine stocks, output receipt to printer, and some more CRUDs. He wrote it in dBase III+. A few years later he migrated to FoxPro 2.6 for DOS and finally in a few more years he rewrote his app in Visual FoxPro 9. And now (actually two years ago) he wants to rewrite it in PHP, but he don't know how. The Visual FoxPro version of this app is still running and has no serious problem except sometimes it performs slowly. Usually there are 1-5 concurrent users. The binary and database files are shared via windows share. He did all the coding as a hobby and for free (it is for his own clinic after all). He also use this app in two other offices he managed. Some reasons of why he wants to rewrite in PHP-MySQL: He wants to learn Easier to deploy (?) Easier client setup, need only a browser What should I do to help my father? How should he start? I explored some options: I let my father learn PHP and MySQL (and HTML (and JavaScript?)) from scratch. I create/bundle framework. I'm thinking on bundling CodeIgniter and a web UI framework (any suggestion?) especially to reduce effort on writing presentation codes. What do you think? tl;dr My father (a doctor) wants to rewrite his Visual FoxPro app in PHP-MySQL. He knows very little of PHP and MySQL but he wants to learn. What should I do to help? How should he start? Some facts: My father is 50 years old. His first encounter with a PC is in early 1980s. It was IBM PC with Intel 8088. He knows BASIC. He taught me how to use DOS and how to program with BASIC. The other language he knows fairly well is dBase/FoxPro. I got my bachelor CS degree last year. I know the internals of my father's app because sometime he wants me to help him writing his app. Sorry for my english.

    Read the article

  • determine if udp socket can be accessed via external client

    - by JohnMerlino
    I don't have access to company firewall server. but supposedly the port 1720 is open on my one ubuntu server. So I want to test it with netcat: sudo nc -ul 1720 The port is listening on the machine ITSELF: sudo netstat -tulpn | grep nc udp 0 0 0.0.0.0:1720 0.0.0.0:* 29477/nc The port is open and in use on the machine ITSELF: lsof -i -n -P | grep 1720 gateway 980 myuser 8u IPv4 187284576 0t0 UDP *:1720 Checked the firewall on current server: sudo ufw allow 1720/udp Skipping adding existing rule Skipping adding existing rule (v6) sudo ufw status verbose | grep 1720 1720/udp ALLOW IN Anywhere 1720/udp ALLOW IN Anywhere (v6) But I try echoing data to it from another computer (I replaced the x's with the real integers): echo "Some data to send" | nc xx.xxx.xx.xxx 1720 But it didn't write anything. So then I try with telnet from the other computer as well: telnet xx.xxx.xx.xxx 1720 Trying xx.xxx.xx.xxx... telnet: connect to address xx.xxx.xx.xxx: Operation timed out telnet: Unable to connect to remote host Although I don't think telnet works with udp sockets. I ran nmap from another computer within the same local network and this is what I got: sudo nmap -v -A -sU -p 1720 xx.xxx.xx.xx Starting Nmap 5.21 ( http://nmap.org ) at 2013-10-31 15:41 EDT NSE: Loaded 36 scripts for scanning. Initiating Ping Scan at 15:41 Scanning xx.xxx.xx.xx [4 ports] Completed Ping Scan at 15:41, 0.10s elapsed (1 total hosts) Initiating Parallel DNS resolution of 1 host. at 15:41 Completed Parallel DNS resolution of 1 host. at 15:41, 0.00s elapsed Initiating UDP Scan at 15:41 Scanning xtremek.com (xx.xxx.xx.xx) [1 port] Completed UDP Scan at 15:41, 0.07s elapsed (1 total ports) Initiating Service scan at 15:41 Initiating OS detection (try #1) against xtremek.com (xx.xxx.xx.xx) Retrying OS detection (try #2) against xtremek.com (xx.xxx.xx.xx) Initiating Traceroute at 15:41 Completed Traceroute at 15:41, 0.01s elapsed NSE: Script scanning xx.xxx.xx.xx. NSE: Script Scanning completed. Nmap scan report for xtremek.com (xx.xxx.xx.xx) Host is up (0.00013s latency). PORT STATE SERVICE VERSION 1720/udp closed unknown Too many fingerprints match this host to give specific OS details Network Distance: 1 hop TRACEROUTE (using port 1720/udp) HOP RTT ADDRESS 1 0.13 ms xtremek.com (xx.xxx.xx.xx) Read data files from: /usr/share/nmap OS and Service detection performed. Please report any incorrect results at http://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 2.04 seconds Raw packets sent: 27 (2128B) | Rcvd: 24 (2248B). The only thing I can think of is a firewall or vpn issue. Is there anything else I can check for before requesting that they look at the firewall server again?

    Read the article

  • ssh tunnel to a remote CUPS server

    - by drevicko
    There is a CUPS server beyond a firewall and I'd like to use it's printers. I have ssh access to computers that can access the CUPS server, and can get at the servers web interface by forwarding say port 1631. I cannot forward port 631 as I've not got root access to anything on the servers network. In Ubuntu's 'Printing' control panel, I can enter the address of a server, but I've not been able to connect through the forwarded port (localhost:1631, which is forwarded to the remote CUPS server's 631 port). Any ideas?

    Read the article

  • Communicating with a remote host via HTTPS

    - by user619818
    I have developed a solution where a Java applet makes a socket connection to a port on a socket server (which happens to run on a web server). But a new client has implemented https within their LAN and so I am told communication must be via HTTPS. With standard socket communication you connect to a port on a host. But the clients HTTPS uses port 443. So will it be possible to connect to a socket server using a different port? I assume it must be possible? Any help would be much appreciated.

    Read the article

  • Wireless drivers

    - by Kencer
    The results for my laptop are as below. How will i install wireless drivers and graphics? $ lspci 00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09) 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 00:14.0 USB controller: Intel Corporation Panther Point USB xHCI Host Controller (rev 04) 00:16.0 Communication controller: Intel Corporation Panther Point MEI Controller #1 (rev 04) 00:1a.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #2 (rev 04) 00:1b.0 Audio device: Intel Corporation Panther Point High Definition Audio Controller (rev 04) 00:1c.0 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 1 (rev c4) 00:1c.1 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 2 (rev c4) 00:1c.3 PCI bridge: Intel Corporation Panther Point PCI Express Root Port 4 (rev c4) 00:1d.0 USB controller: Intel Corporation Panther Point USB Enhanced Host Controller #1 (rev 04) 00:1f.0 ISA bridge: Intel Corporation Panther Point LPC Controller (rev 04) 00:1f.2 SATA controller: Intel Corporation Panther Point 6 port SATA Controller [AHCI mode] (rev 04) 00:1f.3 SMBus: Intel Corporation Panther Point SMBus Controller (rev 04) 02:00.0 Network controller: Broadcom Corporation Device 4365 (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 07) $ sudo lshw -c network *-network UNCLAIMED description: Network controller product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 version: 01 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list configuration: latency=0 resources: memory:f0500000-f0507fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 07 serial: 3c:97:0e:85:c0:0d size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl8168e-3_0.0.4 03/27/12 ip=172.16.96.36 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:43 ioport:2000(size=256) memory:f0404000-f0404fff memory:f0400000-f0403fff $ rfkill list all 0: tpacpi_bluetooth_sw: Bluetooth Soft blocked: no Hard blocked: no

    Read the article

  • pptp VPN, routing

    - by Adrian
    Details: eth0 = current internet port pptp1 = VPN connection, if I connect to my provider, he give me an IP address, which is accessible from the internet. This is what I need. I want to connect through this IP back to my PC. I want to keep my primary internet connection (eth0) on my PC for all traffic, but route traffic to VPN for specified application/or port, to access application/port from the IP, which I given from the pptp provider. Huhh? Difficult but, it is possible? If yes, how? Incoming port will be always: 33340 Outgoing port can be change, but usually it is 33330

    Read the article

  • Best way to deploy my node.js app on a Varnish/Nginx server

    - by Saif Bechan
    I am about to deploy a brand new node.js application, and I need some help setting this up. The way my setup is right now is as follows. I have Varnish running on external_ip:80 I have Nginx behind running on internal_ip:80 Both are listening on port 80, one internal port, one external. NOTE: the node.js app runs on WebSockets Now I have the my new node.js application that will listen on port 8080. Can I have varnish set up that it is in front of both nginx and node.js. Varnish has to proxy the websocket to port 8080, but then the static files such as css, js, etc has to go trough port 80 to nignx. Nginx does not support websockets out of the box, else I would so a setup like: varnish - nignx - node.js

    Read the article

  • Startech SVx41HDI Series Server Remote Control Usage Question - How do I switch away from a dead por

    - by tajh
    We have a Startech KVM over IP model SV841HDI and it was stuck pointing a port where the machine has been removed. We ended up having to physically plug something into that port in order to switch ports again, meaning that if someone in support accidentally switches to an empty port, we need to have a documented solution for making it useable again. The unit is old, no longer under warranty, firmware updates for it are no longer available (interestingly it runs a powerPC version of busybox). Since it does work well except for this one catch, we would like to avoid replacing it. Reading the manual, you have a several recommended methods. I tried them. Hit the left CTRL key a few times (as well as all the other popular KVM keys I could think of). The VNC GUI offers lots of buttons - none of them switch away from a dead port. The question is: how do I switch away from a dead port on this particular KVM remotely?

    Read the article

  • Can Ping but Cannot Telnet directly to SQL Server 2012 Cluster Nodes

    - by tresstylez
    We have a monitoring tool (Solarwinds Orion) that needs to connect to a 2-node failover SQL Server Cluster. For reasons outside of our control -- we cannot monitor the CLUSTER IP directly at this time, so we have fallen back to monitoring each cluster node IP directly. This is not working. Upon troubleshooting, we tried to test that the cluster node was listening on the proper (fixed) port by using telnet to the cluster node IP/port -- and the telnet failed. However, telnet'ing to the Cluster IP/Port was SUCCESSFUL! Each node has its own IP. Each node is listening on the identical FIXED port. Each node has Dynamic Ports disabled. Each node can be PINGED successfully from the monitoring tool. Windows Firewall is DISABLED. How can I troubleshoot why I cannot telnet to the listening port on the cluster nodes?

    Read the article

  • SSH not working from outside network

    - by alexander7567
    Ok.. First off my ISP does not block ports. I run web server just fine from another machine. I have port forwarded port 22. I can access within network but not out of.. I.E. my android. I get "The Operation Timed Out" on ConnectBot. Oh and I have allowed 22 on UFW. To answer what exactly happened was my ISP blocks port 22, even though a while back they told me they do not block any ports.. I changed it to port 27 and it worked without a problem.

    Read the article

  • HP Wireless Printer not working

    - by Omri Spector
    I have installed an HP DeskJet 4620 driver on a win 7 machine. All works perfectly for several days, and than printing is not longer possible. Instead I get the message: "Unable to communicate with printer". This happened on every Win 7 PC I tried, and none of the HP/MS sites contain any relevant info... (Posting this so that the answer appears online, as I did solve it after much work) Solution: It appears that HP installation puts a unique "port" called "HP Network re-discovery". It stops working after some time (possibly after the first time the printer/pc enter sleep mode). BUT, the standard MS TCP port works just fine. So: Go to "Printers" Right click Printer Click "Printer properties" and then "Printer" or "Fax" (for both - do all this twice) Click "Add Port..." Select "Standard TCP Port" Fill in details Move printer to use the new port by un-checking the old one and checking the new one Happy printing.

    Read the article

  • Upgrade from 13.04 to 13.10 broke remote SSH access?

    - by stackoverflowuser95
    I can no longer connect via SSH to my Ubuntu instance after upgrading from 13.04 to 13.10 with: # do-release-upgrade Connecting with $ ssh -vvv [ip here] gives me: OpenSSH_6.3, OpenSSL 1.0.1e 11 Feb 2013 debug2: ssh_connect: needpriv 0 debug1: Connecting to [ip here] [[ip here]] port 22. debug1: connect to address [ip here] port 22: Connection timed out ssh: connect to host [ip here] port 22: Connection timed out So I tried uncommenting #PasswordAuthentication yes in /etc/ssh/sshd_config, and restarting with /etc/init.d/ssh restart; but there was no difference.

    Read the article

  • Choppy USB mice on just one of USB ports

    - by user20532
    I've got Lenovo b560 laptop with latest, properly updated Kubuntu on it (11.04 natty, kernel 2.6.38-8-generic). It has three USB2.0 ports onboard. I usually plug a mouse into one of them (I've got 3 different mice - in office, at home and for when on the go). Sometimes, usually after laptop awakening from sleep, the mouse still works but cursor movements are choppy, as if the processor was extremely loaded (it's usually not). I found that if I re-plug the mouse cord into the other USB port, it works just fine. If I plug it back to problematic port, it is still choppy and remains choppy until next boot. Of course I want my mice to always work fine. Problem is: I cannot reproduce this behavior for sure, it happens sporadically but regularly. I use different USB ports (problem has ever happened on each of them since), I use different mice (each has failed me this way at least once), I cannot generally find what exactly is going wrong and why plugging to different port fixes the mouse instantly. So I'd like to hear at least clues where to look at, what to try to identify my problem. A bit of update: while beginning this post, I had the issue once again. I have just replugged the mouse back to problematic port and it is not recognized at all. On the other port it works smoothly.

    Read the article

  • USB hub keep changing ports

    - by Danniel Magno
    I have an external powered USB hub and I'm using gammu to send some SMSs, but every time the daemon connect to one specific modem, it has the port changed. Gammu is able to send just one SMS and after that the port is changed. I've already tried using: /dev/ttyUSB3 /dev/serial/by-path/pci-0000:00:0b.0-usb-0:3.4.3:1.0-port0 There is anything to do which will stop the ports to be changed or use any other fixed port? Thanks.

    Read the article

  • access server from blocked machine

    - by user40994
    I want to access my Linux server(vnc) from a distant machine which has most ports blocked with the exception of 21, 25, 80, 135, and 445. So, I would like to know if theres a way to communicate with my vnc server on the server, while using an available port on client. i.e. port 25 So I think essentially I need the serverside router to forward packets coming in on port 25 to linux server machine(servername, p5900), which should forward them on to itself on port 5900. And when transmitting, I need the server OR to router to send out packets changing their port to 25. Im totally lost on how to acheive this. Please help(much appreciated). Thanks I do not use smtp.

    Read the article

< Previous Page | 89 90 91 92 93 94 95 96 97 98 99 100  | Next Page >