Search Results

Search found 11077 results on 444 pages for 'ip'.

Page 98/444 | < Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >

• OpenVPN IPV6 Tunnel Radvd

  - by Arenstar

  Hello.. I have an interesting question regarding ipv6 + openvpn.. My Version is OpenVPN 2.1.1 i have been given a native /64 ipv6 network ( for this example 2001:acb:132:acb::/64 ) The plan was/is, route this block through openvpn and into an office ( for testing purposes ) Soo to explain.. I have a Centos Box as the first linux "router" in a datacenter & a Ubuntu box as the second linux "router" in the office I have created a simple point-to-point tunnel using tun ( based off ipv4 address to start the tunnel ) I have assigned to Centos /sbin/ip addr add fed1::1/128 dev eth0 /sbin/ip addr add fed2::2/128 dev tun0 /sbin/ip route add 2001:acb:132:acb::/64 dev tun0 ## ipv6 Block down the tunnel /sbin/ip route add ::/0 dev eth0 ## Default out to Gateway I have assigned to Ubuntu /sbin/ip addr add fed1::3/128 dev tun0 /sbin/ip addr add fed1::4/128 dev eth0 /sbin/ip route add 2001:acb:132:acb::/64 dev eth0 ## ipv6 Block down to eth0 /sbin/ip route add ::/0 dev tun0 ## Default up the tunnel I have also included on both servers.. sysctl -w net.inet6.ip6.forwarding=1 Looks Good... right??? Wrong.. :( I am not able to ping fed1::1 from fed1::4 (Ubuntu) (can ping :4,:3,:2) However, i can ping fed1::1 fed1::2 from :3 ?????? ( very strange ) I am able to access the internet from any ipv6 interface on the Centos Box but clearly not from the Ubuntu box.. Further, i will eventually run radvd on the Ubuntu box eth0, and autoconf the network with ipv6 address's Anyone with some advice / tips to help me out.. ??? Cheers

  Read the article

• pfSense router on a LAN with two gateways

  - by JohnCC

  I have a LAN with an ADSL modem/router on it. We have just gained an alternative high-speed internet connection at our location, and I want to connect the LAN to it, eventually dropping the ADSL. I've chosen to use a small PFSense box to connect the LAN to the new WAN connection. Two servers on the LAN run services accessible to the outside via NAT using the single ADSL WAN IP. We have DNS records which point to this IP. I want to do the same via the new connection, using the WAN IP there. That connection permits multiple IPs, so I have configured pfSense using virtual IP's, 1:1 NAT and appropriate firewall rules. When I change the servers' default gateway settings to the pfSense box, I can access the services via the new WAN IPs without a problem. However, I can no longer access them via the old WAN IP. If I set the servers' default gateway back to the ADSL router, then the opposite is true - I can access the services via the ADSL IP, but not via the new one. In the first case, I believe this is because an incoming SYN packet arrives at the ADSL WAN IP, and is NAT'd and sent to the internal IP of the server. The server responds with a SYN/ACK which it sends via its default gateway, the pfSense box. The pfSense box sees a SYN/ACK that it saw no SYN for and drops the packet. Is there any sensible way around this? I would like the services to be accessible via both IPs for a short period at least, since once I change the DNS it will take a while before everyone picks up the new address.

  Read the article

• DNS failover in a two datacenter scenario

  - by wanson

  I'm trying to implement a low-cost solution for website high availability. I'm looking for the downsides of the following scenario: I have two servers with the same configuration, content, mysql replication (dual-master). They are in different datacenters - let's call them serverA and serverB. Users use serverA - serverB is more like a backup. Now, I want to use DNS failover, to switch users from serverA to serverB when serverA goes down. My idea is that I setup DNS servers (bind/powerdns) on serverA and serverB - let's call them ns1.website.com and ns2.website.com (assuming I own website.com). Then I configure my domain to use them as its nameservers. Both DNS servers will return serverA IP as my website's IP. If serverA goes down I can (either manually or automatically from serverB) change configuration of serverB's DNS, to return IP of serverB as website's IP. Of course the TTL will be low, as it's supposed to be in DNS failovers. I know that it may take some time to switch to serverB (DNS ttl, time to detect serverA failure, serverB DNS reconfiguration etc), and that some small part of users won't use serverB anyway. And I'm OK with that. But what are other downsides of such an approach? An alternative scenario is that ns1.website.com will return serverA IP as website's IP, and ns2.website.com will return serverB IP as website's IP. But AFAIK clients not always use primary nameserver and sometimes would use secondary one. So some small part of users would use serverB instead of serverA which is not quite what I'd like. Can you confirm that DNS clients behave like that and can you tell what percentage of clients would possibly use serverB instead of serverA (statistically)? This one also has the downside that when serverA goes back up, it will be automatically used as website's primary server, which is also a bad situation (cold cache, mysql replication could fail in the meantime etc). So I'm adding it only as a theoretical alternative. I was thinking about using some professional DNS failover companies but they charge for the number of DNS requests and the fees are very high (why?)

  Read the article

• Route all wlan0 traffic over tun0

  - by Tuinslak

  I'm looking for a way to route all wlan0 traffic (tcp and udp) over tun0 (openvpn). However, all other traffic originating from the device itself should not be routed through tun0. I'm guessing this could be realized using iptables or route, but none of my options seem to work. # route add -net 0.0.0.0 gw 172.27.0.1 dev wlan0 SIOCADDRT: No such process Info: This is because the VPN server is not redundant, and wlan users are not really important. However, all services running on the device are fairly important and having a VPN virtual machine with no SLA on it is just a bad idea. Trying to minimize the odds of something going wrong. So setting the VPN server as default gateway is not really an option. I also want all wlan0 user to use the VPN server's IP address as external IP. Edit with the script provided: root@ft-genesi-xxx ~ # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 172.27.0.17 0.0.0.0 255.255.255.255 UH 0 0 0 tun0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.13.37.0 0.0.0.0 255.255.255.0 U 0 0 0 wlan0 172.27.0.0 172.27.0.17 255.255.192.0 UG 0 0 0 tun0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 root@ft-genesi-xxx ~ # ./test.sh RTNETLINK answers: No such process root@ft-genesi-xxx ~ # cat test.sh #!/bin/sh IP=/sbin/ip # replace with the range of your wlan network, or use fwmark instead ${IP} rule add from 10.13.37.0/24 table from-wlan ${IP} route add default dev tun0 via 127.72.0.1 table from-wlan ${IP} route add 10.13.37.0/24 dev wlan0 table from-wlan

  Read the article

• DD-WRT Acces Point as a Router

  - by Dzh

  Following suggestion to this question asked on Network Engineering, I am asking the question here. this is an extension to my previous question (I think it was deleted), where I was claiming that DDWRT was disabling it's DHCP server once connected to the network. I was wrong, as it now seems that it is bridging itself with another parallel connected wireless router. I have two Draytek 2820 and one Netgear WG602v3 with latest DDWRT. Lets call one wired-Draytek and it has wireless disabled. The other one, let's call it wireless-Draytek, is connected to wired-Draytek and has wireless with MAC filtering enabled. Once I connect Netgear to the wired-Draytek, the client that connects to Netgear, will be assigned with IP address from the wireless-Draytek. If the MAC address is not on the wireles-Draytek, the client is unable to obtain IP address and has no connectivity at all, even with manually assigned static IP configuration. To illustrate further, this is how network is set up: wired-Draytek ---------- wireless-Draytek \_________ Netgear What I wish to have, is that Netgear issues IP addresses from it's own IP pool and ignores the MAC filtering rules from wireless-Draytek. This is kind of puzzling how this they are bridging (if they are) themselves automatically. Thanks. UPDATE: It's not a home network. I gave you a bit simplified set-up. If there is a better site on Stack Exchange to ask this, please let me know. The Drayteks are running stock firmware, it's only Netgear that I've flashed to get more stability. In addition to these routers, I have also three 3COM Baseline switch 2824, and another Draytek router with Prosafe FS752TP PoE switch dedicated for VoIP phones. Wired-Draytek has IP 10.0.0.1, DHCP disabled as there is AD DC which is issuing IP addresses. Wireless-Draytek has IP 1.1.1.1 and DHCP enabled. Netgear has default - 192.168.1.1. As per suggestion, the specific question is - how do I isolate these two wireless routers?

  Read the article

• How to troubleshoot Linksys E4200 Remote Management

  - by Jordan

  My Linksys E4200 is configured for Remote Management, but the router is not accepting the connections. Here's the configuration under Administration Management Remote Management Access: Remote Management: Enabled Access via: HTTP Remote Upgrade: Disabled Allowed Remote IP Address: Any IP Address Remote Management Port: 8080 The router is setup to use 192.168.10.41 as its static Internet IP address, and 192.168.35.1 as its LAN IP address. I can access the router just fine via its LAN IP address, but I can't make a connection using http://192.168.10.41:8080. I've tried variations of the settings above (enabled HTTPS, enabled Remote Upgrade, set an IP range of 192.168.10.1-254) but nothing has worked yet. Hoping someone can at least point me in the right direction. Thanks. Update: To clarify, I have a wired router that connects straight to the T1 modem. It's configured to use 192.168.10.1-254 as its internal LAN range. The E4200 wireless router in question is on that LAN using 192.168.10.41 as its WAN IP address. The E4200's internal LAN range is 192.168.35.1-254. I'm not trying to access the E4200 from the Internet, I'm just trying to access it from its WAN IP address. Thanks.

  Read the article

• Nginx Multiple If Statements Cause Memory Usage to Jump

  - by Justin Kulesza

  We need to block a large number of requests by IP address with nginx. The requests are proxied by a CDN, and so we cannot block with the actual client IP address (it would be the IP address of the CDN, not the actual client). So, we have $http_x_forwarded_for which contains the IP which we need to block for a given request. Similarly, we cannot use IP tables, as blocking the IP address of the proxied client will have no effect. We need to use nginx to block the requested based on the value of $http_x_forwarded_for. Initially, we tried multiple, simple if statements: http://pastie.org/5110910 However, this caused our nginx memory usage to jump considerably. We went from somewhere around a 40MB resident size to over a 200MB resident size. If we changed things up, and created one large regex that matched the necessary IP addresses, memory usage was fairly normal: http://pastie.org/5110923 Keep in mind that we're trying to block many more than 3 or 4 IP addresses... more like 50 to 100, which may be included in several (20+) nginx server configuration blocks. Thoughts? Suggestions? I'm interested both in why memory usage would spike so greatly using multiple if blocks, and also if there are any better ways to achieve our goal.

  Read the article

• Domino HTTP Server: Error - Unable to Bind 1.2.3.4, port 80, port in use or Bind To Host configuration specifies a duplicate IP address/host

  - by pdewaard

  We have a Domino 9.0.1 Server hosted on Ubuntu 14.04 Server, which hosts several other http based Tasks, (Nginx, Couchdb, Confluence on Tomcat). The Ubuntu Server has multiple IPs, all bind correctly to the different Tasks. The Domino SMTP task binds correctly and is working well. All http tasks (other than Domino) are proxied behind Nginx version 1.6x and all are working well, netstat shows no 0.0.0.0 bindings, no one is listening on 1.2.3.4:80 . when I try to load http on the (Domino) server console it failes with HTTP Server: Error - Unable to Bind 1.2.3.4, port 80, port in use or Bind To Host configuration specifies a duplicate IP address/host a couple of times, may be 4 or 5 times then it loads without failure! And: when it comes up, I see http is listening on 80 AND 443, but SSL Connections are not working, nor any error log! It must be a kind of bad magic :-( thanks in advance Pitt

  Read the article

• How to set a management IP on a Dell powerconnect 5524/5548 switch?

  - by John Little

  When you first power on a 5524, connected via the serial console, you are offered a setup wizard where you can enter the management IP/Net/Gateway and enter the admin password. HOWEVER, if you dont do this in 60 seconds, the wizard dissapears, and there seems to be no way to run it again - even if you reboot the box. No commands work in the CLI, it just gives you this prompt: If you type say enable, or login, it gives: >login Unknown parameter May be one from the following list: debug help So no commands seem to work. The CLI reference guide does not seem to have any way to run the wizard, or to set the management port or admin passwords. So by not responding in 60 secons after boot, the unit is bricked. Any ideas?

  Read the article

• Cisco ASA 5510 ASDM: Setting up multiple public static ip addresses on a single interface and route

  - by ssjaken

  HI, i have a cisco ASA 5510 using ASDM version 6.3 We have a webserver that is been written very specifically and i was given super direct "DO NOT DEVIATE" directions. This server has to get traffic from 3 different PUBLIC ip's that we own. (our isp gave use a block of 12 static addresses) on 4 different ports. there are the directions i was given externalIP1:22 - 172.17.5.50:22 - SSH externalIP1:443 - 172.17.5.50:23040 - SIT externalIP2:443 - 172.17.5.50:33040 - STAGE externalIP3:443 - 172.17.5.50:43040 - PROD My first question is, using ASDM (my contract employer demands i use ASDM over CLI) how do i get three public addresses to work on one interface. We are authenticating on PPPoE. I know create a virtual interface with the static address but when i do i cannot ping the address from another offsite machine. secondly, where would i put the traffic redirect in. would i go ahead and create ACL's or just make NAT routes. Thanks.

  Read the article

• IP addresses for Windows Azure servers seem to be from the US, when the servers are supposed to be located in Europe

  - by paradroid

  I have a couple of test servers on Windows Azure. One is in the North Europe location and the other is in West Europe. I yet to get around to testing which location offers better connection speeds from where I am (London, UK). The Northern Europe Azure datacentre is apparently in Ireland and the West Europe datacentre is in the Netherlands, which is weird in itself I think. But what I am confused about are the IP addresses are both 168.63.xxx.xxx. GeoIP lookup says that they are both located in the US, and traceroute from London to the addresses get to the US before failing to respond pings. What's going on?

  Read the article

• if I put accept all 0.0.0.0/0 means this server is totally open for any ip ?

  - by davyzhang

  ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 is this means allow all ip from all port? but I still can not visit the server except I go through the allowed ip address and if I put this line in any line, did I make this server totally open for any connection? the full iptable list is below Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 116.211.25.89 0.0.0.0/0 ACCEPT all -- 222.215.136.8 0.0.0.0/0 ACCEPT all -- 125.82.87.21 0.0.0.0/0 ACCEPT all -- 127.0.0.1 127.0.0.1 ACCEPT tcp -- 61.172.251.109 0.0.0.0/0 tcp spt:8080 ACCEPT tcp -- 61.172.254.123 0.0.0.0/0 tcp spt:8080 ACCEPT tcp -- 61.129.44.191 0.0.0.0/0 ACCEPT tcp -- 61.129.44.128 0.0.0.0/0 ACCEPT tcp -- 61.172.251.109 0.0.0.0/0 tcp spt:8080 ACCEPT tcp -- 61.172.254.123 0.0.0.0/0 tcp spt:8080 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 0 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 8 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:53 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp spt:53 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp spt:123 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:123 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:20 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:21 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:80 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:88 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:8000 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:8080 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:8888 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:873 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:6969 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp spt:6900 ACCEPT tcp -- 61.172.241.98 0.0.0.0/0 ACCEPT tcp -- 61.172.247.98 0.0.0.0/0 ACCEPT tcp -- 61.172.247.100 0.0.0.0/0 ACCEPT tcp -- 61.152.122.33 0.0.0.0/0 ACCEPT tcp -- 61.152.110.130 0.0.0.0/0 ACCEPT tcp -- 210.51.28.220 0.0.0.0/0 ACCEPT tcp -- 210.51.28.120 0.0.0.0/0 ACCEPT tcp -- 61.172.241.120 0.0.0.0/0 ACCEPT tcp -- 211.147.0.85 0.0.0.0/0 ACCEPT tcp -- 211.147.0.114 0.0.0.0/0 ACCEPT tcp -- 222.73.61.249 0.0.0.0/0 ACCEPT tcp -- 222.73.61.250 0.0.0.0/0 ACCEPT tcp -- 222.73.61.251 0.0.0.0/0 ACCEPT tcp -- 210.51.31.11 0.0.0.0/0 tcp dpt:38422 ACCEPT tcp -- 210.51.31.12 0.0.0.0/0 tcp dpt:38422 ACCEPT tcp -- 61.172.254.123 0.0.0.0/0 tcp spt:8080 ACCEPT tcp -- 61.172.251.109 0.0.0.0/0 tcp spt:8080 ACCEPT tcp -- 61.172.247.85 0.0.0.0/0 ACCEPT tcp -- 222.73.12.248 0.0.0.0/0 ACCEPT tcp -- 61.172.254.184 0.0.0.0/0 ACCEPT tcp -- 61.172.254.78 0.0.0.0/0 ACCEPT tcp -- 61.172.254.243 0.0.0.0/0 ACCEPT tcp -- 61.152.97.115 0.0.0.0/0 ACCEPT tcp -- 221.231.128.206 0.0.0.0/0 ACCEPT tcp -- 221.231.130.199 0.0.0.0/0 ACCEPT udp -- 172.0.0.0/8 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 10.0.0.0/8 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 192.168.0.0/16 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 61.172.252.58 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 61.183.13.201 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 222.73.2.11 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 221.208.157.158 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 218.30.74.250 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 202.102.54.234 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 125.64.2.115 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 222.73.23.23 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 210.51.33.97 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 210.51.33.98 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 222.73.11.112 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 222.73.11.111 0.0.0.0/0 udp dpt:161 ACCEPT udp -- 222.73.11.89 0.0.0.0/0 udp spt:38514 DROP tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:38423 REJECT tcp -- 0.0.0.0/0 0.0.0.0/0 reject-with tcp-reset DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT) target prot opt source destination DROP all -- 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- 0.0.0.0/0 222.73.11.89 udp dpt:38514

  Read the article

• Good way to run commands on remote computer without its own public-facing IP address (Linux Centos)

  - by Chris Dutrow

  Have a few computers running Linux Centos 6.4. They are connected to an unmanaged switch, which in turn, is connected to a router (Verzion Fios issue). What is a good way to "log in" to one of the computers so that I can run commands? Do I need to use SSH, or something different? Since the computers do not have their own public-facing IP addresses, do I need to set up some kind of port forwarding within the router? What is a simple, reliable way to accomplish this? Thanks so much!

  Read the article

• How to disable Tcp/Ip settings in windows 7 via GPO?

  - by Akash Kava

  I have enabled following policies, "Prohibit TCP/IP advanced connection" "Prohibit access to properties of components of a LAN connection" "Enable Windows 2000 Network Connections setings for Administrators" after doing all these, all machines running windows xp, 2000 and vista have network settings properties button disabled as expected. However all machines running windows 7 have no effect, I believe there are few more steps, all Windows 7 machines are on domain and we want to control this via Domain Controler's GPO. Please let me know, what I need to do to have Windows 7 disable the properties of network connection, I am not network expert, I read few articles about what new has been added in GPO of windows 7 but I am blank. Everything works fine on Windows XP, Vista, 2003 Server. Only Windows 7 is a problem.

  Read the article

• VMWare Player guest does not re-aquire IP on bridged interface after host loses and re-acquires network connectivity

  - by Vineet

  I am running a Ubuntu Linux image in VMWare Player on my laptop. The host is Windows XP. There are two network adapters configured in VMWare Player - one is host-only and the other is bridged. Everything works fine as long as the host does not lose network connectivity. If the host loses connectivity (even briefly) and then re-acquires it, my bridged adapter in VMWare Player is still unable to get an IP address. The host-only adapter remains unaffected. Disconnecting/Reconnecting the bridged adapter does not help. Simply restarting the guest OS does not help. Restarting VMWare Player does not help. The only remedy is to reboot the host and then bring up VMWare Player all over again. Is there something I can try to avoid this reboot? I searched the existing questions but they seemed to talk about adapters in NAT mode, whereas I am interested in retaining Bridged mode.

  Read the article

• Why would my router have different MAC addresses for IP and IPv6 transactions?

  - by user329161

  Today I was using tcpdump and I noticed my computer was having IPv6 traffic with a particular MAC address that I could not match with an IP using nmap or arping. After looking at the tcpdump logs a little more closely, I figured out it was another MAC address my router was using but exclusively for IPv6 traffic. 22:49:01.936830 90:0d:cb:ff:31:91 (oui Unknown) > 33:33:00:00:00:01 (oui Unknown), ethertype IPv6 (0x86dd), length 158: fe80::920d:cbff:feff:3191 > ip6-allnodes: ICMP6, router advertisement, length 104 Why would a router offer a different MAC address for IPv6?

  Read the article

• How to Configure IIS 7.5 to Host Several Classic ASP Sites using 1 IP Address?

  - by SidC

  We are running Windows Server 2008 R2 with IIS 7.5 and have 4-5 Classic ASP sites to install. The main site is stored in wwwroot and the other sites are stored in folders below wwwroot. We have 1 IP address for the server. How do I configure IIS to allow folks to browse/test the sites before domain names are pointed to te server? When I setup one of the sites in a subfolder of wwwroot and assign a separate port to it, I receive a message stating: Config Error Cannot add duplicate collection entry of type 'add' with unique key attribute 'value' set to 'index.asp' How do I remedy this error and permit IIS to render the site?

  Read the article

• using iptables to change a destination port but keep the ip the same.

  - by Scott Chamberlain

  I am playing around with transparent proxies, The current way I am doing things is the program makes a request to a computer on port 80, I use iptables -t nat -A OUTPUT -p tcp --destination-port 80 -j REDIRECT --to-port 1234 to redirect to my proxy that I am playing with. the proxy will send out a request to port 81 (as all outbound port 80 are being fed back in to the proxy so I want to do something like iptables -t nat -A OUTPUT -p tcp --destination-port 81 -j DNAT --to-destination xxxx:80 The problem lies with the xxxx part. How do I change the destination port without changing changing the destination ip? Or am I doing this setup completely wrong, I am learning after all and constructive criticism is definitely appreciated.

  Read the article

• Can I set up a COM Port that Connects via TCP/IP?

  - by Kristopher Johnson

  I have an RS232 device connected to a Digi PortServer on my network. I can telnet to the Digi's IP and port number to communicate with that RS232 device. I have a Windows application that knows how to talk to the device, but it wants to connect directly to an RS232 port. So, my question: Is there some way to set up a COM port so that when this application connects to it, it goes through the network to the Digi to communicate with the device? I have run across the utility TCP-Com, which seems like it might be a solution. Is this the best option?

  Read the article

• How to associate a domain name and IP address?

  - by StackedCrooked

  The situation is as follows: I am renting a dedicated server using SliceHost. On this server I have installed a small HTTPServer. I can verify that it works by nativating directly to its IP address (example). I have also purchased a domain name from gandi.net and would like to link it with to my server. However, I'm having much trouble finding clear instructions on how to create this link. After a few hours of reading documentation and trying out things I ended up the following configuration. on the DNS registrar I have specified the following settings: on the Slicehost server I specified these "records": But it doesn't seem to work. I end up on this page telling me the domain name is not available. Does anyone have an idea what I am doing wrong?

  Read the article

• Why ping another innet machine from MacBook get netgate's ip address?

  - by Xinwang

  I have three machine in my home network connected by a wireless router. One is server installed linux at 192.168.1.1, another is Thinkpad with MS Windows XP at 192.168.1.2, last one is MacBook Pro with Mac OS X 10.6.3 at 192.168.1.3. When I ping the Linux Server from Thinkpad (MS Windows XP) I can get the correct ip address, but when I ping it from Mac I get the global address of my router, like 61.135.181.175. Could you tell me why this happen? And how do I get same ping result on Mac and Windows. Thanks

  Read the article

• Does an SMTP request contain host header information (or just the IP of the targeted SMTP server)?

  - by Olaf

  We are using an external commercial smtp server for our newsletters (sending them through .NET components), and they offer two smtp URLs - smtp.critsend.com and fast.critsend.com -, and the second one is reserved for sending singular emails, the first one for bulk. Using nslookup shows that both resolve to the same 4 IP addresses (fast.critsend.com being an Alias). Question: (how) is it possible for the smtp relay to distinguish between different names? Is there something in the headers that can be compared to host headers in http protocol (I didn't find any intelligible information for a non-sysadmins)? The reason I'm asking is because we would like to use one of the IPs in our newsletter script (which works) rather than a name (in order to save DNS requests), and we are wondering about potential problems.

  Read the article

• Win 2003 STD network adapter always showing DHCP when in static IP configuration, + it loses the DNS

  - by Darragh

  Hi, I have a server that after the first configuration it was DHCP, now I have added it to our domain and in a static IP, however after a few moments it returns to DHCP but with only some of the IPv4 setting staying the same, It loses DNS for example. I'm not sure what is causing the problem but all I know is this started to happen after I added it to the domain, Would it be a domain policy? or the NIC drivers Spec; Dell M605 Blade server Windows 2003 STD SP1 Intel Xeon Quad core NIC: Dual embedded Broadcom NetXtreme IITM 5708 Gigabit Ethernet NIC w/ TOE

  Read the article

• Why ping another inet machine from MacBook get netgate's ip address?

  - by Xinwang

  I have three machine in my home network connected by a wireless router. One is server installed linux at 192.168.1.1, another is Thinkpad with MS Windows XP at 192.168.1.2, last one is MacBook Pro with Mac OS X 10.6.3 at 192.168.1.3. When I ping the Linux Server from Thinkpad (MS Windows XP) I can get the correct ip address, but when I ping it from Mac I get the global address of my router, like 61.135.181.175. Could you tell me why this happen? And how do I get same ping result on Mac and Windows. Thanks

  Read the article

• Can't copy Ilias-folder via FQDN, but via ip-address?

  - by Lars

  I have an Ilias-Installation, which is available through two virtual hosts: the FQDN and the ip-address. The first server is ssl only, the second plain http. Both configuration files look the same except for the SSL-part: SSLEngine on SSLCertificateFile /etc/apache2/ssl/ilias.pem In the Ilias-Webinterface, I can copy a folder on the plain http. But if I try to copy the same folder on the ssl virtual host, I get the notice, that the copy was started (rough german translation here), but the folder does not show up. There are no errors in the error-logs of php or the webserver and as said, no differences beside the ssl-part. The guys at an ilias-forum did not have an idea, either. Any ideas in here?

  Read the article

< Previous Page | 94 95 96 97 98 99 100 101 102 103 104 105  | Next Page >