Search Results

Search found 4248 results on 170 pages for 'adsl router'.

Page 99/170 | < Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >

• Configuration of Sonicwall Load Balancing

  - by jacke672

  We installed a Sonicwall NSA 240 appliance and have configured it up for our SSL VPN connection and for load balancing with 2 ADSL lines. Over the past week, I have been testing the load balancing options to optimize the connection speeds for our users - but I've run into the following: Round Robin load balancing is the ideal load balancing setting and it's roughly doubling our throughput- but, when it's active users are unable to access any SSL enabled websites such as banking, web-mail, etc. For this reason, I have been using percentage based balancing as it allows me to enable source and destination IP binding, which doesn't 'break' any secure connections but were left with the slow connection speeds we had before adding the second line. I'm looking for a method in which we can take advantage of the round robin connection speeds while allowing users to access sites with SSL certificates, all while still allowing our remote (vpn) users to connect. Any help would be appreciated. Thanks

  Read the article

• Windows 7 VPN Error 619

  - by TravisPUK

  So I am running Windows 7 Enterprise. This morning I was able to VPN using the built in VPN (Connect to Work Network etc). I had to change my network's IP address range and now the VPN will not work. It just stalls on the Verifying user name and password... message. But then it returns the 619 error. Anybody know why changing my machine's IP address would cause this problem? Where should I be looking to try and fix this issue? I have tried this on a Windows XP machine that also had the IP address range change and this still connects fine using exactly the same connection details. EDIT The internal network range changed from 192.x.x.x to 10.x.x.x. This was done on the entire Active Directory. All machines are running fine and the Windows XP machine, that works going to the same client VPN mentioned above is on the same network. Both the XP and the Win 7 machines are using DHCP served by the Domain Controller. The client domain is not performing any IP range checks/restrictions. The VPN is outside the internal network, connection is being made via the Internet and not passing through any other machine, other than the normal domain machines, ie DNS etc. This is passing through a router and the router has the relevant VPN passthrough options configured. All internal machines are working correctly with other forms of VPN, ie Cisco, Sonic etc (these were tested on other machines, they are not installed on the Vista or Win7 machines). After further testing, this is occurring on all Win7 and Vista machines where they can no longer connect to the client VPN, however all XP machines can still connect fine. This has been tested on three Vista, two Win7 and five XP machines. All machines are on DHCP and tests have been done with both the firewalls turned on and off, as well as with fixed IPs being used. Thanks Travis

  Read the article

• Can I autoregister my clients/servers in local DNS?

  - by Christian Wattengård

  Right now I have a W2k12 server at home that I run as a domain controller. This has the extra benefit of registering every "subordinate" computers name in it's DNS so that I don't have to go around remembering IP's all the time. (And it let's me easily run dhcp also on my servers). I need to rework my home network for several odd reasons, and in this new scenario there is no place for a big honking W2k12 server box. I have a RasPI, and I have other smallish linux boxen I can use. (In a worst case scenario I'll use my NUC, but then I'll be forced to use my home cinema's UPnP-client for media... The HORROR!!) Is it possible to set up a DNS-server-"appliance" that somehow autoregisters it's own hostname.. Scenario: Router (N66u) on 172.20.20.1. Runs DHCP on 172.20.20.100-200 range. Server [verdant] of a *nix flavor on 172.20.20.2 Laptop [speedy] of W8 flavor on DHCP assigned Laptop [canary] of W8 flavor on DHCP assigned Desktop [lianyu] of Ubunto flavor on DHCP assigned What I would like is that all of the above servers (except possibly the router) would be available on verdant.starling.lan and canary.starling.lan and so on. This is how it works right now (except the Ubuntu box... I haven't cracked that one yet) because Windows just does this for you.. I would also be able to do this without any manual labor on the server. When I tell my box it's name is smoak it should "immediately" be available as smoak.starling.lan without any extra configuration on my part. How can I do this in a Linux (Ubuntu) environment? (Bonus comment upvote for naming the naming scheme :P )

  Read the article

• Is Gmail Being Blocked by my ISP (wait till you read this)?

  - by James

  This is the strangest thing I have ever encountered. I have a desktop on which I cannot access Gmail and also youtube sign in (I believe since youtube is owned by google they both use the same sign in system). So okay, maybe my ISP is blocking these for some reason or maybe my firewall is, or maybe there is something wrong with my connectivity, right? NO. On other computers that uses the same connection via a wireless router I can access both gmail and youtube sign in just fine. On this computer which doesn't have a wireless card and so I have to connect via Ethernet cable (connected to a USB converter since the Ethernet port doesn't work anymore) I can access all sites and services including things like aol and hotmail. But only when it comes to gmail, do I get complete and utter throttling. I even turned off my AV ad Firewall momentarily and no luck. The gmail ages starts to load and by mid point it just stays there loading and loading and loading... never ends. I tried everything, I reset the modem and router multiple times. I reinstalled my operating system from a vista to a windows 7 hoping a complete reinstall would solve the issue, but no luck. So can anyone for the life of them figure out why this could be? And yes, I am going to call my ISP but not to solve this issue, but to cancel them. I want to upgrade to cabel from DSL anyway. I didn't mention my ISP because I'm not sure if that is within the rules (if it's okay some one let me know and I will). P.S. All this happened one day, before gmail was perfectly accessible in this computer. I can't remember anything special that happened on that day prior to this. The only thing I can think of is, my ISP or Google itself is blocking this computer based on it's mac address, but I don't know if that's even done. Additional info: PC: Windows 7 Ultimate 32 bit Connection Type: DSL Connecting Medium: Ethernet cable via USB converter

  Read the article

• Private staff network within public network

  - by pianohacker

  I'm the sysadmin at a small public library. Since I got here a few years ago, I've been trying to set up the network in a secure and simple way. Security is a little tricky; the staff and patron networks need to be separated, for security reasons. Even if I further isolated the public wireless, I'd still rather not trust the security of our public computers. However, the two networks also need to communicate; even if I set up enough VMs so they didn't share any servers, they need to use the same two printers at the very least. Currently, I'm solving this with some jerry-rigged commodity equipment. The patron network, linked together by switches, has a Windows server connected to it for DNS and DHCP and a DSL modem for a gateway. Also on the patron network is the WAN side of a Linksys router. This router is the "top" of the staff network, and has the same Windows server connected on a different port, providing DNS and DHCP, and another, faster DSL modem (separate connections are very useful, especially as we heavily depend on some cloud-hosted software). tl;dr: We have a public network, and a NATed staff network within it. My question is; is this really the best way to do this? The right equipment would likely make my job easier, but anything with more than four ports and even rudimentary management quickly becomes a heavy hit on our budget. (My original question was about an ungodly frustrating DHCP routing issue, but I thought I'd ask whether my network was broken rather than asking about the DHCP problem and being told my network was broken.)

  Read the article

• How to pipe internet radio into a tuner?

  - by JW

  UPDATE: Thanks everyone for the ideas! This was an area I knew very little about but now I can talk with a little more expertise about it. Much appreciated! Visited my dad this weekend and he wants to pipe some internet radio he's found down to a tuner on quite a distance away in the house. He uses computers for only very basic things: e-mail, getting the Post crossword, checking Yahoo!, checking recipes, etc. There's currently one computer in the house (no router). My initial suggestion (without any research whatsoever) was to get a wireless router and a netbook for downstairs near the tuner, but he initially wasn't too keen about having another computer down there. Anyway, is there any computer hardware that could magically pipe the audio output from the computer down to one set of (RCA) audio inputs on the tuner? Wireless isn't necessary but it probably would be easier. Anyway, thanks for your suggestions! UPDATE Thanks everyone! Voted up all of your suggestions now that I have 15 rep. Much appreciated.

  Read the article

• What is the IPv6 equivalent to IPv4 RFC1918 addresses?

  - by Kumba

  Having a hard time wrapping my head around IPv6 here. A lot of the lingo seems targeted at enterprise-level IPv6 deployments, discussing link-local, site-local, global unicast, scopes, etc. Not a lot of solid information on really small networks, like home networks. I want to check my thinking and make sure I am getting the correct translations from IPv4-speak to IPv6-speak. The first question is, what's the equivalent of RFC1918 for IPv6? Initial searches suggested there was no equivalent. Then I stumbled upon Unique Local Addresses (RFC4193), and that states that all ULA's should be assigned the prefix fc00, followed by a 40-bit random number in the routing prefix. This random number is to "prevent collisions when two IPv6 networks are interconnected" -- again, another reference to an enterprise-level function. If I have a small local LAN at home, numbered using 192.168.4.0/24, what's my equivalent in IPv6's ULA scope? Assuming I will never, ever, tie that IPv6 address into the real internet (a router will NAT & firewall it), can I ignore the RFC to an extent and go with fc00::4:0/120? It also seems that any address in fc00::/7 are to be globally routable. Does this mean I'll need extra protections so my router would not automatically start advertising these private IPv6 addresses to the world? Second question, what's this link-local thing? Reading suggests a default-assigned address in the fe80::/10 range that has the last 64bits of the address comprised of the interface's MAC address. Seems to be required, too, but I'm annoyed by the constant discussion of it in relation to enterprise networks. Third question, what is scope id for? Seems to be yet another term tossed around in relation to enterprise networks, especially when interconnecting them, but almost no explanation on the smaller home network level. Can I see a scope ID AND CIDR notation used together? I.e., fc00::4:0/120%6, or are scope IDs only supposed to be applied to a single /128 IPv6 address?

  Read the article

• WIFI connection stopped working on Windows - how to troubleshoot

  - by Michiel de Mare

  Friends and family often come to me with this problem, and while I usually manage to fix their problems eventually, it often take me several hours. I'm sure there are many of us in the same position. Also, friends rarely seem to know which provider they're using, or what the password is of their WIFI-connection or ADSL-router. I'd like to gather that information myself. I'd like to have a checklist to diagnose and fix the problem, and a set of utilities on an usb-stick to help me. Where to start?

  Read the article

• What could cause TFTP reloaded Cisco `running-config` on 871 to fail?

  - by xtian

  Cisco CCP Write Configuration borked my 871w config while I was trying to setup port forwarding. I went through the basic steps to reconfig the router. I looked to see if I could just reset the router. Nope. I tested the 871's flash memory with fsck to see if there was hardware failure. Nope. Then I rewrote the minimal config for TFTP (which is the same for Cisco's CCP app.). Thne, I successfully uploaded a previously working running-config from Win Vista using SolarWinds TFTP Server, unfortunately the restore was not entirely successful. The old running config was saved to the 871's startup-config and I can login using console port. Some other things that are working are the hostname and welcome message but that's about it. Startup shows an error SETUP: new interface NVI0 placed in "shutdown" state after tftp. The missing light on the access point modem for ethernet link show the 871'a outside FE4 is not working. SO...what's the possible problem with reloading a previously working config (approximately 4 months with the same config) via TFTP? Is there something I can look for on the 871 to verify the config? Or on Vista to validate the config file itself before I transfer it? Or, is this there a common TFTP issue? UPDATE. I missed the instruction from Cisco's TFTP page to delete aaa lines from the config (although a video from a SuperUser user didn't make this point in his most excellent demo). There were several lines of this sort, I deleted them and uploaded again. However, they're back. I assume they're added automatically? [nope, see answer] UPDATE 2. The reload of previous settings was successful, but this error remains. I don't even know now if it was there before or not. It seems irrelevant to the question.

  Read the article

• Prevent master to fall back to master after failure

  - by Chrille

  I'm using keepalived to setup a virtual ip that points to a master server. When a failover happens it should point the virtual ip to the backup, and the IP should stay there until I manually enable (fix) the master. The reason this is important is that I'm running mysql replication on the servers and writes should only be on the master. When I failover I promote the slave to master. The master server: global_defs { ! this is who emails will go to on alerts notification_email { [email protected] ! add a few more email addresses here if you would like } notification_email_from [email protected] ! I use the local machine to relay mail smtp_server 127.0.0.1 smtp_connect_timeout 30 ! each load balancer should have a different ID ! this will be used in SMTP alerts, so you should make ! each router easily identifiable lvs_id APP1 } vrrp_instance APP1 { interface eth0 state EQUAL virtual_router_id 61 priority 999 nopreempt virtual_ipaddress { 217.x.x.129 } smtp_alert } Backup server: global_defs { ! this is who emails will go to on alerts notification_email { [email protected] ! add a few more email addresses here if you would like } notification_email_from [email protected] ! I use the local machine to relay mail smtp_server 127.0.0.1 smtp_connect_timeout 30 ! each load balancer should have a different ID ! this will be used in SMTP alerts, so you should make ! each router easily identifiable lvs_id APP2 } vrrp_instance APP2 { interface eth0 state EQUAL virtual_router_id 61 priority 100 virtual_ipaddress { 217.xx.xx.129 } notify_master "/etc/keepalived/notify.sh del app2" notify_backup "/etc/keepalived/notify.sh add app2" notify_fault "/etc/keepalived/notify.sh add app2” smtp_alert }

  Read the article

• Loss of network connectivity when playing video on Optoma HD180 projector

  - by Jeff Fohl

  Hi Folks - New to Super User, so I hope this question fits in with the guidelines. Very strange problem I am having, and I am at a loss as to how to continue troubleshooting this one. The basic problem is that when I attempt to watch streamed video on a particular display device (an Optoma HD180 projector), my network connectivity drops like a stone to barely measurable levels. This is my setup: I have a Dell H2C 730x running Windows 7 64bit. This particular computer has two ATI Radeon HD 4800 video cards. I have two Samsung 22" monitors connected to one card, and an Optoma HD180 digital projector connected to the other card via an HDMI cable. My internet connection is normally a reliable 6Mbps. The problem I am having occurs when I stream video (or even just browse the web) on the Optoma Projector. When I do this, my internet connection drops to practically zero (just a few kilobits per second). When I move the browser away from the projector, and over to one of my Samsung monitors, the internet connection comes right back. Note that the Optoma projector is on and enabled as a third monitor all this time. I can move the mouse around on the projector without triggering the problem. I tried pinging my router when I was playing a movie on one of the monitors, and I get a 1 millisecond response. However, when I have the movie playing on the Optoma projecter, pinging the router gives me response times in the hundreds of milliseconds, or times out completely. So, it clearly is something local to my machine - and not some sort of throttling occurring down the line. I would think that it is possibly something to do with the HDMI driver conflicting somehow with my network driver (which is a USB-based wireless connection). This one has me really stumped. Anyone have any ideas?

  Read the article

• OpenVPN IPV6 Tunnel Radvd

  - by Arenstar

  Hello.. I have an interesting question regarding ipv6 + openvpn.. My Version is OpenVPN 2.1.1 i have been given a native /64 ipv6 network ( for this example 2001:acb:132:acb::/64 ) The plan was/is, route this block through openvpn and into an office ( for testing purposes ) Soo to explain.. I have a Centos Box as the first linux "router" in a datacenter & a Ubuntu box as the second linux "router" in the office I have created a simple point-to-point tunnel using tun ( based off ipv4 address to start the tunnel ) I have assigned to Centos /sbin/ip addr add fed1::1/128 dev eth0 /sbin/ip addr add fed2::2/128 dev tun0 /sbin/ip route add 2001:acb:132:acb::/64 dev tun0 ## ipv6 Block down the tunnel /sbin/ip route add ::/0 dev eth0 ## Default out to Gateway I have assigned to Ubuntu /sbin/ip addr add fed1::3/128 dev tun0 /sbin/ip addr add fed1::4/128 dev eth0 /sbin/ip route add 2001:acb:132:acb::/64 dev eth0 ## ipv6 Block down to eth0 /sbin/ip route add ::/0 dev tun0 ## Default up the tunnel I have also included on both servers.. sysctl -w net.inet6.ip6.forwarding=1 Looks Good... right??? Wrong.. :( I am not able to ping fed1::1 from fed1::4 (Ubuntu) (can ping :4,:3,:2) However, i can ping fed1::1 fed1::2 from :3 ?????? ( very strange ) I am able to access the internet from any ipv6 interface on the Centos Box but clearly not from the Ubuntu box.. Further, i will eventually run radvd on the Ubuntu box eth0, and autoconf the network with ipv6 address's Anyone with some advice / tips to help me out.. ??? Cheers

  Read the article

• 2 servers on 2 networks in same office

  - by irot

  Hello Gents, My office doesn't have a "server guy" in employ, so I'm stuck with having to fix server issues for now. There are 2 servers in our office, both are file/web servers only accessible via LAN. They are currently on the same network, so no issue there. Problem is, we recently got a static IP to use, but it's with a different ISP, so now we have 2 routers in our office. I would like to open one of the servers to the public as a web/FTP server. But if I hook a server up to the new router, users will no longer be able to access the files shared on that server (because they're on different networks). How can I go about making one server accessible to the public using the static IP line, but still able to share the files on it to the users connected to the other network? The server I want to make public is running Windows Server 2008, the other server Windows Server 2003. And as far as I know, IP addresses are assigned by the router. I'm just a developer, don't know much about networking. Thank you in advance.

  Read the article

• Bridging Wireless and Wired Interfaces in Linux

  - by The Daemons Advocate

  My network setup is something like: Wireless Router <---> Netbook <---> Ubuntu Desktop ...or, more verbosely (with interfaces): Wireless Router <--(wireless)--> (eth2) Ubuntu Netbook Ubuntu Netbook (eth0) <---(wired)----> (eth0) Ubuntu Desktop In a perfect world, I'd have the desktop wired, but weird circumstances combined with my wanting to understand more about networking in linux make me want to figure out how to bridge these two devices. A bit of googling has given me this example using bridge-utils, and here's how I'm (failing) to setup the bridge (on the netbook): sudo -i ifconfig eth0 0.0.0.0 ifconfig eth2 0.0.0.0 brctl addbr bridget brctl addif bridget eth0 brctl addif bridget eth2 ifconfig bridget up ...then, trying to make sure that the netbook can still get on the internets... route add default gateway 192.168.2.1 dhclient bridget What happens after this is that the dhclient command above (netbook) doesn't get served an IP, and the Desktop, if I run dhclient, it doesn't get served an IP. Some weird considerations might be that I'm running the Network Manager Applet that comes with Ubuntu. While I'm sure I can get a command line wireless configuration setup, it's a bit complex. Can someone give me a shout as to where I'm going wrong? I'd also like to note another related question titled 'Bridging my laptop’s wireless and wired adaptors', however the setup is different to mine.

  Read the article

• NAT vs public IP (and blocked ports)

  - by user1646166

  I have a problem with my ISP. They say that they don't block any ports and I have public IP, while I think these both statements are false. Before I talk to them again (which is really tough when my understanding of these terms is different than theirs) I would like to make some things clear. It seems like my computer is behind NAT (is it possible to have public IP and be behind NAT at the same moment?). When I check my IP, through some external server, and type that IP into browser I get a home page of some router (not mine). Isn't that a proof that my IP isn't public? Also, I have problems with making connections via some ports. E.g. when I'm trying to connect through some high port ( 1023) via SSH, it doesn't work. Is it possible that certain range of outgoing ports from my computer are blocked? Or is it simply because that my ssh client (PuTTY) can't receive incoming packets because of blocked incoming ports? To avoid some questions: it's not a problem with my router, I tried connecting my PC directly and it also didn't work, while having connected by 3G using phone with USB tethering, it does work. Thanks!

  Read the article

• Best Performing Remote Desktop Software for WAN

  - by Dave

  I've been tasked with connecting a computer in one of our branches in the midlands to one in south wales. We have been using windows remote desktop but find it too slow. The ADSL on the computer were connecting to is about 6Mb Download and 470Kb Upload so not majorly fast. That connection is also shared with about 10 other internet users. I'm trying to find out if the is any remote desktopn connecting software that performs better than the microsoft remote desktop software. Or, would i be better using a KVM over IP? I've looked into connecting the offices through BT's fiber optic but at £21k a year rental were trying to find a cheaper solution! Any help would be great. Thanks, Dave,

  Read the article

• Issues with VPN functionality

  - by Xorandor

  I've been working on setting up VPN connectivity to our office location. We bought a Cisco WRV210 which have a builtin VPN server. Cisco has some software QuickVPN, which is not as quick and easy as I had thought. I've had mixed experiences on different machines with connecting. Instead I configured an IPSec VPN tunnel following a guide from TheGreenBow here http://www.thegreenbow.com/doc/tgbvpn_cg_linksys_wrv200_en.pdf I followed their instructions and tried out an evaluation of their software, and VPN connection should be working ok. I'm able to do RDP to a machine on the network (using IP address, not machine name) and ping the router etc. What I'm trying to solve are two things: It's not like I'm "really" on the network. Or at least I'm restricted to some degree when going through the VPN. I can't access a machine on the network using machine name, only IP. I can't ping a machine, but the router just fine. Could this be that something is not set up properly? If so, I can ofcourse supply additional information. Second, when I log onto the VPN, I would really like my outgoing connection to go through the internet connection of the remote location. Basically if I connect to the VPN I want my outgoing IP to be that of the remote location's (needed for some IP resctrictions on some of our servers). At a previous work location it worked like this when we connected to our office VPN over PPTP and the builtin windows VPN client. I'm not a huge expert on the topic, so any hints will be appreciated.

  Read the article

• Why can't I renew my dynamic IP address?

  - by qwerty

  So, I'm going to explain this from the start. I've started a project with a friend of mine which includes a webspider, that crawls through all pages on a site and stores them in a DB. Since I've never done this before, I didn't think about the amount of requests I was actually sending to the site, and after a day or two I finally got my IP blocked. I need to be able to visit that site as it's very important to me. Not only for my project, but for other reasons too. (and if I'm able to renew my IP I'm going to set a delay on the crawler so I don't get blocked & DDOS the site) I have a dynamic IP address, at least that's what my router settings say. I've tried ipconfig /flushdns, ipconfig /release, restart computer. No result. I end up with the same IP address. I've also tried renewing it from the router, however, I think it uses the same method which isn't working. Is it possible that site has blocked my mac address? Can a site even access my mac address?

  Read the article

• How to diagnose remote assistance problem

  - by cantabilesoftware

  I have a long standing issue with remote assistance between a home and work PC. My wife and I both use MSN messenger and I used to be able to control her PC at home via MSN Remote Assistance. Some time ago however this stopped working and I don't know why. We're both running the latest versions of MSN Live Messenger and I've checked the appropriate firewall ports are open, but it still doesn't work and MSN just says something useless like "The person isn't responding". Any suggestions for how can I diagnose this? More info: I just tried direct Remote Desktop between work PC and home PC and it works fine - so I presume all the appropriate ports are open. Just Remote Assistance doesn't work. I'd like to get RA working so I can demonstrate how to do things remotely. With Remote Desktop the person at the other end gets booted off and can't see. With Remote Assistance they can follow along step by step. Some comments below suggest using other solutions, which is fine and do work, but there must be a way to diagnose RA and get it working. Experimenting with this some more, the notebook that I was using at work today that refused to connect works fine for remote assistance when I bring it home. So I guess this must be a problem with our network configuration at work. I've checked that 3389 is open on firewall on office router and remote desktop works both ways.... just not remote assistance. I've read that remote assitance won't work if client and server are both behind Non-UPnP/NAT routers. If one has UPnP it's supposed to work. Office router doesn't have UPnP enabled but my home one does. I've also scoured the event logs on both ends, nothing noteworthy - unless I'm looking in the wrong spot). Note (copied from comment): I've just tried ShowMyPC which is based on VNC and it works, but I'd still like to figure out what's wrong with RA - it's just bugging me. The question is only about Remote Assistance, no need to propose solutions based on other programs.[/edit by Gnoupi]

  Read the article

• Time capsule on windows 7

  - by Kiva

  Hi guys, I have a time machine to backup my mac book pro. All work fine with it. Now, my girlfriend have a PC on windows 7. She wants to backup her PC with cobian backup on the time machine. But her PC doesn't see the time capsule, so it's impossible to connect it. The Time capsule is connected on my box adsl with wifi and the mac and the pc are connected on the box with wifi. Why windows doesn't see the TC ? I installed "bonjour" on the PC but nothing worked. Thanks for your help.

  Read the article

• ospfd over an OpenVPN link - strange error in logs

  - by Alex

  I am trying to set up Quagga ospfd on two hosts connected by an OpenVPN link. These hosts have VPN IPs 10.31.0.1 and 10.31.0.13. ospfd config is pretty simple: hostname bizon password xxxxxxxxx enable password xxxxxxxxx ! log file /var/log/quagga/ospfd.log ! interface lo ! interface tun0 ip ospf network point-to-point ip ospf mtu-ignore ip ospf cost 10 interface tun1 ip ospf network point-to-point ip ospf mtu-ignore ip ospf cost 10 interface tun2 ip ospf network point-to-point ip ospf mtu-ignore ip ospf cost 10 ! router ospf ospf router-id 10.31.0.1 network 10.31.0.0/16 area 0.0.0.0 network 10.119.2.0/24 area 0.0.0.0 redistribute connected area 0.0.0.0 range 10.0.0.0/8 ! line vty ! debug ospf event debug ospf packet all I am getting the following error in the ospfd.log (the log is from 10.31.0.13): 2012/10/05 01:25:28 OSPF: ip_v 4 2012/10/05 01:25:28 OSPF: ip_hl 5 2012/10/05 01:25:28 OSPF: ip_tos 192 2012/10/05 01:25:28 OSPF: ip_len 64 2012/10/05 01:25:28 OSPF: ip_id 64666 2012/10/05 01:25:28 OSPF: ip_off 0 2012/10/05 01:25:28 OSPF: ip_ttl 1 2012/10/05 01:25:28 OSPF: ip_p 89 2012/10/05 01:25:28 OSPF: ip_sum 0xe5d1 2012/10/05 01:25:28 OSPF: ip_src 10.31.0.1 2012/10/05 01:25:28 OSPF: ip_dst 224.0.0.5 2012/10/05 01:25:28 OSPF: Packet from [10.31.0.1] received on link tun1 but no ospf_interface I'm not sure what to do next. I have set up ospfd over OpenVPN several times but I used Debian and I am on CentOS 6 now. Quagga version is 0.99.15. Should I try to get more recent version?

  Read the article

• Windows Firewall Software to Filter Transit Traffic

  - by soonts

  I need to test my networking code for Nintendo Wii under the conditions when some specific Internet server is not available. Wii is connected to my PC with crossover ethernet cable. PC has 2 NICs. PC is connected to hardware router with ethernet cable. The hardware router serves as NAT and has an internet connected to its uplink. I set the Wii to be in the same lan as PC by using Windows XP Network bridge. I can observe the WII network traffic using e.g. Wireshark sniffer. Is there a software firewall that can selectively filter out transit traffic? (e.g. block outgoing TCP connections to 123.45.67.89 to port 443) I tried Outpost Pro 2009 and Comodo. Outpost firewall blocks all transit traffic with it's implicit "block transit packet" rule. If the transit traffic is explicitly allowed by creating the system-wide low level rule, then it's allowed completely and no other filter can selectively block it. Comodo firewall only process rules when the packet has localhost's IP as either source or destination, allowing the rest of the traffic. Any ideas? Thanks in advance! P.S. Platform is Windows XP 32 bit, no other OSes is allowed, Windows ICS (Internet Connection Sharing) doesnt work since the Wii is unable to connect, becides I don't like the idea of adding one more level of NAT.

  Read the article

• SQL Server Remote Connections

  - by Barry

  Hi, I am at my wits end with trying to access a remote SQL Server 2008 R2 Express instance. Here are the following that I have tried. 1) I enabled remote connections in the instance properties. 2) I enabled sql server and windows authentication mode and created an account to log in using sql server authentication. 3) I started the SQL Server Browser service 4) I forwarded ports 1433 and 1434 on the router to the IP address of the machine hosting SQL Server. 5) I turned off firewalls on both the Machine running the instance and the router. 6) http://www.yougetsignal.com/tools/open-ports/ I used this to check whether or not both ports were open and it says that they are closed. I have the SQL Server Express instance running and the browser running. I have configured it to allow remote connections yet, it tells me they are both closed. I'm pretty confused at this stage. On the client Machine I am trying to connect using the following format machineip\SQLEXPRESS with SQL Server Management Studio Express. Thanks in advance

  Read the article

• SQL Server Remote Connections

  - by Barry

  Hi, I am at my wits end with trying to access a remote SQL Server 2008 R2 Express instance. Here are the following that I have tried. 1) I enabled remote connections in the instance properties. 2) I enabled sql server and windows authentication mode and created an account to log in using sql server authentication. 3) I started the SQL Server Browser service 4) I forwarded ports 1433 and 1434 on the router to the IP address of the machine hosting SQL Server. 5) I turned off firewalls on both the Machine running the instance and the router. 6) http://www.yougetsignal.com/tools/open-ports/ I used this to check whether or not both ports were open and it says that they are closed. I have the SQL Server Express instance running and the browser running. I have configured it to allow remote connections yet, it tells me they are both closed. I'm pretty confused at this stage. On the client Machine I am trying to connect using the following format machineip\SQLEXPRESS with SQL Server Management Studio Express. Thanks in advance

  Read the article

• Suggestions for a SOHO/Home Asterisk system

  - by James

  I would like to buy a small embedded system that runs Linux and Asterisk. I would like two FXS ports ( to plug analogue phones into ) and one FXO port ( to plug in to my real line to allow access to the POTS ). I would like it to have a USB port to hold storage for voicemail. I really want it for home use so I would like it to be under £150 ( say $250 ), given that you can buy ADSL routers for around this much can any of them be made to run Linux and Asterisk? I don't want a PC as the power usage would be too high. I am looking for something like this ASDL router but open and able to run Asterisk or another open PBX. At worst I would like a box which had one FXO and two FXS and just made them completely available over IP to a full Asterisk system on a low power Atom system.

  Read the article

< Previous Page | 95 96 97 98 99 100 101 102 103 104 105 106  | Next Page >