Search Results

Search found 2087 results on 84 pages for 'sever room'.

Page 1/84 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • Cooling for a small server room

    - by John Zwinck
    I have a server room about 12 feet square with an unfinished ceiling (exposed ducts and wiring). It houses a few servers (about ten, 1U and 2U) and some networking gear (four 1U switches, three routers, three modems, two cable boxes). With the door closed, it runs around 80 degrees Fahrenheit with half the servers turned on. When I turned on all the servers it reached 86 before I chickened out and propped the door open. The room is adjacent to air-conditioned office space, but does not itself have dedicated air conditioning. The ventilation for this room seems to be limited to one duct coming in at ceiling level, with a powered fan to draw air in, and one duct at ceiling level to allow air to flow out (it seems like it may just go into the drop ceiling cavity in the adjacent room). The adjacent office space stays fairly cool, but I'd prefer not to leave the door propped open all the time. There is both 110v and 208v service in the room, and plenty of power available. But there are no windows, and no floor drains (in a pinch we might be able to run a condensation hose through a small hole we'd drill in the wall to a nearby sink area, but only if absolutely necessary). I've considered portable A/C units, but I'm not sure on sizing and a lot less sure how we would run the exhaust hose(s). I suppose we could point one at the existing room exhaust duct (air return), but substantially modifying the duct is probably a no-no. I've also considered installing a fan box in the door of the room, but I'm concerned that this will only drop the temperature a little. Even right now, with all the equipment on, the room is at 83 degrees with the door open. And the main building A/C turns off daily at 6 PM to conserve energy, so the adjacent room temperature rises at night. How would you cool this room? Let's say the goal is to bring the temperature with everything running from a steady state of around 90 degrees down to 75 (equivalently, to offset the heat produced by ten 1U servers).

    Read the article

  • Server Room Protocols/Server Room Management

    - by Matthew E
    Hi, I'm new to this site but have found the articles and feedback very useful. We have a Server Room which our Organisation owns and controls, yet there are several thirs party companies that have open access to this room. As such, we have been asked to put together a protocol paper that stipulates the standards that we expect to be adhered to when working in this room. Other than the monitoring of UPS loads, Air Cooling functionality, alarm systems etc, does any one have any guidance on the kind of issues that need to be documented to make this protocol all encompassing? I'm thinking along the lines of not leaving cardboard or other combustibles in the room, not having food and drink in the room, not altering the fabric of the building by drilling through walls etc? Many thanks in advance for any guidance provided.

    Read the article

  • Domino 8.5.3 forward room reservation request to external email

    - by Cividan
    I have created a room reservation database on my notes server. Now my problem is that we have 2 company that will use this room and I would like to forward the meeting request sent to this room to external email address so that the other company email server receive the reservation request and update the calendar on their side to see the accurate availability of the room. How can I achive this. Thanks !

    Read the article

  • Monitoring server room temperature

    - by user640
    I have a small server room with its own AC unit. Recently, the AC died, and the temperature increased from 70 F to 90 F. We rarely go in this room, so I was lucky that someone happened to notice that the fans were running a lot louder than normal as they walked past the door. It looks like I need a way to be notified when the temperature in that room gets too hot. What tools are you using to monitor the temperature in your server room? How does this tool notify you of a problem (email, SNMP, etc). Note: I've read this question on server temperature, but I'm interested in the whole room, not just the inside of a server case. Edit: Thanks for all the great responses so far! Many of these products measure much more than just temperature. What else should I be looking at and why?

    Read the article

  • A dusty server room

    - by pauska
    Here's the story.. The owners of the building we lease office space from decided to do a renovation of the exterior. This involved in some pretty heavy work at the level where our server room is, including exchanging windows wich are fit inside a concrete wall. My red alert went off when I heard that they were going to do the same thing with our server room (yes, our server room has a window. We're a small shop with 3 racks. The window is secured with steel bars.) I explicity told the contractor that they need to put up a temporarily wall between our racks and the original wall - and to make sure that the temporary wall is 100 % air and water-tight. They promised to do so. The temporary wall has a small door in it, so that workers can go in/out through the day (through our server room, wich was the only option....). On several occasions I could find the small door half-way shut while working evenings/nights. I locked the door, and thought that they would hopefully get the point soon and keep the door shut. I even gave a electrician a mouthful when I saw that he didn't close the door properly. By this point - I bet that most of you get a picture of what happened. Yes, they probably left the door open while drilling in the concrete. I present you our 4 weeks old EMC VNX: I'll even put in a little bonus, here is the APC UPS one rack further away from the temporary wall. See the nice little landing strip from my finger? What should I do? The only thing that comes to mind is to either call all our suppliers (EMC, HP, Dell, Cisco) and get them to send technicians to check out all the gear in the server room, or get some kind of certified 3rd-party consulant to check all of it. Would you run production systems on this gear? How long? Edit: I should also note that our aircondition isn't exactly enterprise-grade, given the nature of our small room. It's just a single inverter, wich have failed one time before I started working here (failed inverters usually leads to water dripping out).

    Read the article

  • Moving server room to another part of the building

    - by PHLiGHT
    This question is a bit different than the typical we are moving our server room to an off site location or we are moving the whole office to a new building. Management wants to add some more office space and to do so they want to move the server room to another location. The server room has Verizon smart jacks, a few servers, PBX and all the office network drops go into this room. I'm going to go over there to scout out an alternate location for the equipment because that is still TBD. This sounds like quite a pain since the Verizon equipment for our MPLS will need to be moved (never done that) and the office jacks will need to be re-run. How do you handle the jacks? I was thinking of keeping them in the same location and having new wall plates put in with half the ports going to the current location and the other half to the new location. Or do you think that 40 drops could just be done over the weekend so the old stuff would be ripped out and replaced with the new? Currently the wiring is a mess so this could be a blessing in the long run.

    Read the article

  • The perfect server room?

    - by splattne
    What do I have to consider when I'm planning a new server room for a small company (30 PCs, 5 servers, a couple of switches, routers, UPS...)? What are the most important aspects in order to protect the hardware? What things do not belong in a server closet? Edit: You may also be interested in this question: Server Room Survival Kit. Thank you!

    Read the article

  • A simple message room

    - by webbyJoe
    Can anyone recommend a simple message room (not chat room) which I can use for a private communication between my users. My idea: to grant some users (2-3 at the most) a specific privilege to talk privately in a message room. none of them would be administrator there. I need such features: - admin panel for adding users allowed to post messages in room - room invisible to anyone except users - filtering not-allowed words - Ajax-enabled so that replies appear immediately - other message room features I have a linux hosting so PHP message room would be the best option. I thought of using a forum for this, but it's too much work as a forum is public by nature and I need something private by nature. Any ideas? Thanks in advance.

    Read the article

  • Portable server room air-con options

    - by Bridgette
    We are looking for portable industrial aircond for our server room which whould blow hot air to the sealing cavity, split-system is not an option (http://www.ikoo.com.au/Aircond.png). Something exactly like this would be ideal, but unfortunately not available in AUS: http://www.apc.com/resource/include/techspec_index.cfm?base_sku=ACPA4000&ISOCountrycode=us http://www.apcmedia.com/salestools/ASTE-6Z2RUU_R1_EN.pdf. So we pretty much looking for competing products to the APC's NetworkAIR PA4000 available in AU. ? We currently have 3 x DeLonghi Penguino PACT120, but space is limited and getting more of these is prob not ideal.

    Read the article

  • Server room kit?

    - by Bill Weiss
    I feel like this is a question I've seen on here before, but some searching didn't do me any good. This looks similar, but I'm looking for stuff I leave there, not what's in my go-bag. What would you say is indispensable equipment in your server room? I've inherited one that's a bit light on stuff (except for servers, those are in there). We're in the single digits of racks, if that matters. I'm thinking of things like: Cable labeler Ethernet tester (copper at least, fibre if you need) ... ? Community wiki, because, really. [Edit] I suppose it's important to say that it's a colo facility, kind of far from the office. No food, water, etc. :(

    Read the article

  • Best labeler for the server room?

    - by Matt Simmons
    Right now, I've got a Brother P-touch labeler that prints four or five sizes of text on one long label. It has features such as italics and bold. It's...non-ideal. What do you use in your server room? I have heard of labelers that will print vertically as well as horizontally, or which can produce labels for cable management as well. I also think it would be great to be able to produce barcodes for my tapes (LTO-3). So basically, I would like a labeler that prints normal, can print cable labels, and can print barcodes. Unicorn optional. Any ideas, or could you even suggest the best labeler for each solution?

    Read the article

  • How Can I Populate Default Form Data with a ManyToMany Field?

    - by b14ck
    Ok, I've been crawling google and Django documentation for over 2 hours now (as well as the IRC channel on freenode), and haven't been able to figure this one out. Basically, I have a model called Room, which is displayed below: class Room(models.Model): """ A `Partyline` room. Rooms on the `Partyline`s are like mini-chatrooms. Each room has a variable amount of `Caller`s, and usually a moderator of some sort. Each `Partyline` has many rooms, and it is common for `Caller`s to join multiple rooms over the duration of their call. """ LIVE = 0 PRIVATE = 1 ONE_ON_ONE = 2 UNCENSORED = 3 BULLETIN_BOARD = 4 CHILL = 5 PHONE_BOOTH = 6 TYPE_CHOICES = ( ('LR', 'Live Room'), ('PR', 'Private Room'), ('UR', 'Uncensored Room'), ) type = models.CharField('Room Type', max_length=2, choices=TYPE_CHOICES) number = models.IntegerField('Room Number') partyline = models.ForeignKey(Partyline) owner = models.ForeignKey(User, blank=True, null=True) bans = models.ManyToManyField(Caller, blank=True, null=True) def __unicode__(self): return "%s - %s %d" % (self.partyline.name, self.type, self.number) I've also got a forms.py which has the following ModelForm to represent my Room model: from django.forms import ModelForm from partyline_portal.rooms.models import Room class RoomForm(ModelForm): class Meta: model = Room I'm creating a view which allows administrators to edit a given Room object. Here's my view (so far): def edit_room(request, id=None): """ Edit various attributes of a specific `Room`. Room owners do not have access to this page. They cannot edit the attributes of the `Room`(s) that they control. """ room = get_object_or_404(Room, id=id) if not room.is_owner(request.user): return HttpResponseForbidden('Forbidden.') if is_user_type(request.user, ['admin']): form_type = RoomForm elif is_user_type(request.user, ['lm']): form_type = LineManagerEditRoomForm elif is_user_type(request.user, ['lo']): form_type = LineOwnerEditRoomForm if request.method == 'POST': form = form_type(request.POST, instance=room) if form.is_valid(): if 'owner' in form.cleaned_data: room.owner = form.cleaned_data['owner'] room.save() else: defaults = {'type': room.type, 'number': room.number, 'partyline': room.partyline.id} if room.owner: defaults['owner'] = room.owner.id if room.bans: defaults['bans'] = room.bans.all() ### this does not work properly! form = form_type(defaults, instance=room) variables = RequestContext(request, {'form': form, 'room': room}) return render_to_response('portal/rooms/edit.html', variables) Now, this view works fine when I view the page. It shows all of the form attributes, and all of the default values are filled in (when users do a GET)... EXCEPT for the default values for the ManyToMany field 'bans'. Basically, if an admins clicks on a Room object to edit, the page they go to will show all of the Rooms default values except for the 'bans'. No matter what I do, I can't find a way to get Django to display the currently 'banned users' for the Room object. Here is the line of code that needs to be changed (from the view): defaults = {'type': room.type, 'number': room.number, 'partyline': room.partyline.id} if room.owner: defaults['owner'] = room.owner.id if room.bans: defaults['bans'] = room.bans.all() ### this does not work properly! There must be some other syntax I have to use to specify the default value for the 'bans' field. I've really been pulling my hair out on this one, and would definitely appreciate some help. Thanks!

    Read the article

  • Camera Collision inside the room model

    - by sanddy
    I am having a problem in Calculating the camera collision for my Room model which consists of sofa, tables and other models. The users shall be moving the camera front, back, rotating so i need to make sure that the camera does not collide with any of the models with in the room. I have treated all my models inside the room by BoundingBox[] and the camera by BoundingSphere. So, far i have implemented collision by looking into the tutorial from http://www.toymaker.info/Games/XNA/html/xna_model_collisions.html which was great. But, I guess the problem lies in the Transformation part. I debugged and found some points to be at Vector(-XXX,-XXX,-XXX) where X is digit. Also i found my radius of some models where too large(in thousand, i just looked into its radius value before converting to BoundingBox). Do I need to scale the model for collision??? Below are my code:- On My LoadContent(): Matrix[] transforms = new Matrix[myModel.Bones.Count]; myModel.CopyAbsoluteBoneTransformsTo(transforms); int index = 0; box = new List<BoundingBox>(); BoundingBox worldModel = Utility.CalculateBoundingBox(myModel); foreach (ModelMesh mesh in myModel.Meshes) { Vector3[] obb = new Vector3[8]; worldModel.GetCorners(obb); Vector3[] asdf = (Vector3[])obb.Clone(); Vector3.Transform(obb, ref transforms[mesh.ParentBone.Index], obb); BoundingBox worldBox = BoundingBox.CreateFromPoints(obb); box.Add(worldBox); index++; } On CameraPosition Update: BoundingSphere bs = new BoundingSphere(this.cameraPos, 5.0f); if (RoomWalkthrough.Utility.CheckCollision(bs, bb)) { // Do Something } Please Help.

    Read the article

  • Algorithm for detecting windows in a room

    - by user2733436
    I am dealing with the following problem and i was looking to write a Pseudo-code for developing an algorithm that can be generic for such a problem. Here is what i have come up with thus far. STEP 1 In this step i try to get the robot where it maybe placed to the top left corner. Turn Left - If no window or Wall detected keep going forward 1 unit.. if window or wall detected -Turn right -- if no window or Wall detected keep going forward.. if window or wall detected then top left corner is reached. STEP 2 (We start counting windows after we get to this stage to avoid miscounting) I would like to declare a variable called turns as it will help me keep track if robot has gone around entire room. Turns = 4; Now we are facing north and placed on top left corner. while(turns0){ If window or wall detected (if window count++) Turn Right Turn--; While(detection!=wall || detection!=window){ move 1 unit forward Turn left (if window count++) Turn right } } I believe in doing so the robot will go around the entire room and count windows and it will stop once it has gone around the entire room as the turns get decremented. I don't feel this is the best solution and would appreciate suggestions on how i can improve my Pseudo-code. I am not looking for any code just a algorithm on solving such a problem and that is why i have not posted this in stack overflow. I apologize if my Pseudo-code is poorly written please make suggestions if i can improve that as i am new to this. Thanks.

    Read the article

  • Sysadmin Nightmares – Server Room Disasters [Videos]

    - by Asian Angel
    There you are, looking at a pristine server room when disaster suddenly strikes! Whether it is fire, floods, or other causes you will feel sympathy for the sysadmins involved when watching this collection of seven server room disasters that Wired has put together. You can view the other six videos in the collection by visiting the Wired post linked below… Server Snuff: 7 Videos of a Sysadmin’s Worst Nightmares [via Fail Desk] HTG Explains: How Antivirus Software Works HTG Explains: Why Deleted Files Can Be Recovered and How You Can Prevent It HTG Explains: What Are the Sys Rq, Scroll Lock, and Pause/Break Keys on My Keyboard?

    Read the article

  • How to make room reflection using Cubemap

    - by MaT
    I am trying to use a cube map of the inside of a room to create some reflections on walls, ceiling and floor. But when I use the cube map, the reflected image is not correct. The point of view seems to be false. To be correct I use a different cube map for each walls, floor or ceiling. The cube map is calculated from the center of the plane looking at the room. Are there specialized techniques to achieve such effect ? Thanks a lot !

    Read the article

  • How to determine if a 3D voxel-based room is sealed, efficiently

    - by NigelMan1010
    I've been having some issues with efficiently determining if large rooms are sealed in a voxel-based 3D rooms. I'm at a point where I have tried my hardest to solve the problem without asking for help, but not tried enough to give up, so I'm asking for help. To clarify, sealed being that there are no holes in the room. There are oxygen sealers, which check if the room is sealed, and seal depending on the oxygen input level. Right now, this is how I'm doing it: Starting at the block above the sealer tile (the vent is on the sealer's top face), recursively loop through in all 6 adjacent directions If the adjacent tile is a full, non-vacuum tile, continue through the loop If the adjacent tile is not full, or is a vacuum tile, check if it's adjacent blocks are, recursively. Each time a tile is checked, decrement a counter If the count hits zero, if the last block is adjacent to a vacuum tile, return that the area is unsealed If the count hits zero and the last block is not a vacuum tile, or the recursive loop ends (no vacuum tiles left) before the counter is zero, the area is sealed If the area is not sealed, run the loop again with some changes: Checking adjacent blocks for "breathable air" tile instead of a vacuum tile Instead of using a decrementing counter, continue until no adjacent "breathable air" tiles are found. Once loop is finished, set each checked block to a vacuum tile. Here's the code I'm using: http://pastebin.com/NimyKncC The problem: I'm running this check every 3 seconds, sometimes a sealer will have to loop through hundreds of blocks, and a large world with many oxygen sealers, these multiple recursive loops every few seconds can be very hard on the CPU. I was wondering if anyone with more experience with optimization can give me a hand, or at least point me in the right direction. Thanks a bunch.

    Read the article

  • User cannot book a room resource in Exchange 2010

    - by bakesale
    Im having a problem with a specific user not being able to book a room resource. No error message is generated at all. The user attempts to add the room as a meeting resource and it simply doesnt register with the resources calendar. I have tested the resource with other accounts and other rooms for this user but it is only this room that is having issues for this user. This Exchange server was migrated from 2007 to 2010. All rooms except for the problem room were created back on Exchange 2007. This new room was created with Exchange 2010. Maybe this clue has something to do with the problem? This is a paste of the mailboxes folder permissions [PS] C:\Windows\system32Get-MailboxFolderPermission -identity room125:\calendar RunspaceId : 448ab44a-4c2a-4403-b46c-fce1106c0823 FolderName : Calendar User : Default AccessRights : {Author} Identity : Default IsValid : True RunspaceId : 448ab44a-4c2a-4403-b46c-fce1106c0823 FolderName : Calendar User : Anonymous AccessRights : {None} Identity : Anonymous IsValid : True

    Read the article

  • Create room mailbox in Exchange 2007 - cannot view calendar

    - by David Neale
    I'm an application developer and I'm trying to play around with Exchange in order to integrate a room booking system with it. I've created a room mailbox and have set it so that it auto-accepts appointment requests. When creating an appointment as a standard user I can add the room as a resource and its availability will display. However, I can add it as a shared calendar to Outlook 2003 (Unable to display the folder. The Calendar folder could not be found) nor can I return the calendar folder using Exchange Web Services (again, could not find the folder). I've also created an appointment via Exchange Web Services with a room as a resource. The resource was successfully booked (as confirmed when opening it as the room's delegate) but it does not appear on the meeting as viewed by any of the attendees. Is there anything further I need to do in order to share this calendar? How do most organisations set up their Exchange with regards to rooms?

    Read the article

  • User cannot book a room resource

    - by bakesale
    Im having a problem with a specific user not being able to book a room resource. No error message is generated at all. The user attempts to add the room as a meeting resource and it simply doesnt register with the resources calendar. I have tested the resource with other accounts and other rooms for this user but it is only this room that is having issues for this user. This Exchange server was migrated from 2007 to 2010. All rooms except for the problem room were created back on Exchange 2007. This new room was created with Exchange 2010. Maybe this clue has something to do with the problem? This is a paste of the mailboxes folder permissions [PS] C:\Windows\system32Get-MailboxFolderPermission -identity cbr125:\calendar RunspaceId : 448ab44a-4c2a-4403-b46c-fce1106c0823 FolderName : Calendar User : Default AccessRights : {Author} Identity : Default IsValid : True RunspaceId : 448ab44a-4c2a-4403-b46c-fce1106c0823 FolderName : Calendar User : Anonymous AccessRights : {None} Identity : Anonymous IsValid : True

    Read the article

  • Problem with room/screen/menu controller in python game: old rooms are not removed from memory

    - by Jordan Magnuson
    I'm literally banging my head against a wall here (as in, yes, physically, at my current location, I am damaging my cranium). Basically, I've got a Python/Pygame game with some typical game "rooms", or "screens." EG title screen, high scores screen, and the actual game room. Something bad is happening when I switch between rooms: the old room (and its various items) are not removed from memory, or from my event listener. Not only that, but every time I go back to a certain room, my number of event listeners increases, as well as the RAM being consumed! (So if I go back and forth between the title screen and the "game room", for instance, the number of event listeners and the memory usage just keep going up and up. The main issue is that all the event listeners start to add up and really drain the CPU. I'm new to Python, and don't know if I'm doing something obviously wrong here, or what. I will love you so much if you can help me with this! Below is the relevant source code. Complete source code at http://www.necessarygames.com/my_games/betraveled/betraveled_src0328.zip MAIN.PY class RoomController(object): """Controls which room is currently active (eg Title Screen)""" def __init__(self, screen, ev_manager): self.room = None self.screen = screen self.ev_manager = ev_manager self.ev_manager.register_listener(self) self.room = self.set_room(config.room) def set_room(self, room_const): #Unregister old room from ev_manager if self.room: self.room.ev_manager.unregister_listener(self.room) self.room = None #Set new room based on const if room_const == config.TITLE_SCREEN: return rooms.TitleScreen(self.screen, self.ev_manager) elif room_const == config.GAME_MODE_ROOM: return rooms.GameModeRoom(self.screen, self.ev_manager) elif room_const == config.GAME_ROOM: return rooms.GameRoom(self.screen, self.ev_manager) elif room_const == config.HIGH_SCORES_ROOM: return rooms.HighScoresRoom(self.screen, self.ev_manager) def notify(self, event): if isinstance(event, ChangeRoomRequest): if event.game_mode: config.game_mode = event.game_mode self.room = self.set_room(event.new_room) #Run game def main(): pygame.init() screen = pygame.display.set_mode(config.screen_size) ev_manager = EventManager() spinner = CPUSpinnerController(ev_manager) room_controller = RoomController(screen, ev_manager) pygame_event_controller = PyGameEventController(ev_manager) spinner.run() EVENT_MANAGER.PY class EventManager: #This object is responsible for coordinating most communication #between the Model, View, and Controller. def __init__(self): from weakref import WeakKeyDictionary self.last_listeners = {} self.listeners = WeakKeyDictionary() self.eventQueue= [] self.gui_app = None #---------------------------------------------------------------------- def register_listener(self, listener): self.listeners[listener] = 1 #---------------------------------------------------------------------- def unregister_listener(self, listener): if listener in self.listeners: del self.listeners[listener] #---------------------------------------------------------------------- def clear(self): del self.listeners[:] #---------------------------------------------------------------------- def post(self, event): # if isinstance(event, MouseButtonLeftEvent): # debug(event.name) #NOTE: copying the list like this before iterating over it, EVERY tick, is highly inefficient, #but currently has to be done because of how new listeners are added to the queue while it is running #(eg when popping cards from a deck). Should be changed. See: http://dr0id.homepage.bluewin.ch/pygame_tutorial08.html #and search for "Watch the iteration" print 'Number of listeners: ' + str(len(self.listeners)) for listener in list(self.listeners): #NOTE: If the weakref has died, it will be #automatically removed, so we don't have #to worry about it. listener.notify(event) def notify(self, event): pass #------------------------------------------------------------------------------ class PyGameEventController: """...""" def __init__(self, ev_manager): self.ev_manager = ev_manager self.ev_manager.register_listener(self) self.input_freeze = False #---------------------------------------------------------------------- def notify(self, incoming_event): if isinstance(incoming_event, UserInputFreeze): self.input_freeze = True elif isinstance(incoming_event, UserInputUnFreeze): self.input_freeze = False elif isinstance(incoming_event, TickEvent) or isinstance(incoming_event, BoardCreationTick): #Share some time with other processes, so we don't hog the cpu pygame.time.wait(5) #Handle Pygame Events for event in pygame.event.get(): #If this event manager has an associated PGU GUI app, notify it of the event if self.ev_manager.gui_app: self.ev_manager.gui_app.event(event) #Standard event handling for everything else ev = None if event.type == QUIT: ev = QuitEvent() elif event.type == pygame.MOUSEBUTTONDOWN and not self.input_freeze: if event.button == 1: #Button 1 pos = pygame.mouse.get_pos() ev = MouseButtonLeftEvent(pos) elif event.type == pygame.MOUSEBUTTONDOWN and not self.input_freeze: if event.button == 2: #Button 2 pos = pygame.mouse.get_pos() ev = MouseButtonRightEvent(pos) elif event.type == pygame.MOUSEBUTTONUP and not self.input_freeze: if event.button == 2: #Button 2 Release pos = pygame.mouse.get_pos() ev = MouseButtonRightReleaseEvent(pos) elif event.type == pygame.MOUSEMOTION: pos = pygame.mouse.get_pos() ev = MouseMoveEvent(pos) #Post event to event manager if ev: self.ev_manager.post(ev) # elif isinstance(event, BoardCreationTick): # #Share some time with other processes, so we don't hog the cpu # pygame.time.wait(5) # # #If this event manager has an associated PGU GUI app, notify it of the event # if self.ev_manager.gui_app: # self.ev_manager.gui_app.event(event) #------------------------------------------------------------------------------ class CPUSpinnerController: def __init__(self, ev_manager): self.ev_manager = ev_manager self.ev_manager.register_listener(self) self.clock = pygame.time.Clock() self.cumu_time = 0 self.keep_going = True #---------------------------------------------------------------------- def run(self): if not self.keep_going: raise Exception('dead spinner') while self.keep_going: time_passed = self.clock.tick() fps = self.clock.get_fps() self.cumu_time += time_passed self.ev_manager.post(TickEvent(time_passed, fps)) if self.cumu_time >= 1000: self.cumu_time = 0 self.ev_manager.post(SecondEvent(fps=fps)) pygame.quit() #---------------------------------------------------------------------- def notify(self, event): if isinstance(event, QuitEvent): #this will stop the while loop from running self.keep_going = False EXAMPLE CLASS USING EVENT MANAGER class Timer(object): def __init__(self, ev_manager, time_left): self.ev_manager = ev_manager self.ev_manager.register_listener(self) self.time_left = time_left self.paused = False def __repr__(self): return str(self.time_left) def pause(self): self.paused = True def unpause(self): self.paused = False def notify(self, event): #Pause Event if isinstance(event, Pause): self.pause() #Unpause Event elif isinstance(event, Unpause): self.unpause() #Second Event elif isinstance(event, SecondEvent): if not self.paused: self.time_left -= 1

    Read the article

  • Making Room for Innovation — Oracle Interactive eBook

    - by Javier Puerta
    Innovation and complexity are two critical topics on the minds of business leaders. Innovation is what gives them a competitive edge; increased complexity is their greatest challenge. Learn how Oracle is helping customers change the game and make room for innovation by simplifying IT. Access the new Oracle interactive e-book, “Simplify IT and Unleash Innovation”. You can download it here.

    Read the article

  • Making Room for Innovation — Oracle Interactive eBOOK

    - by Cinzia Mascanzoni
    Innovation and complexity are two critical topics on the minds of business leaders. Innovation is what gives them a competitive edge; increased complexity is their greatest challenge. Learn how Oracle is helping customers change the game and make room for innovation by simplifying IT. Access the new Oracle interactive e-book, “Simplify IT and Unleash Innovation” by inviting partners to download it here.

    Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >