Search Results

Search found 328 results on 14 pages for 'esp'.

Page 1/14 | 1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >

  • ASA 5505 stops local internet when connected to VPN

    - by g18c
    Hi I have a Cisco ASA router running firmware 8.2(5) which hosts an internal LAN on 192.168.30.0/24. I have used the VPN Wizard to setup L2TP access and I can connect in fine from a Windows box and can ping hosts behind the VPN router. However, when connected to the VPN I can no longer ping out to my internet or browse web pages. I would like to be able to access the VPN, and also browse the internet at the same time - I understand this is called split tunneling (have ticked the setting in the wizard but to no effect) and if so how do I do this? Alternatively, if split tunneling is a pain to setup, then making the connected VPN client have internet access from the ASA WAN IP would be OK. Thanks, Chris names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Vlan1 nameif inside security-level 100 ip address 192.168.30.1 255.255.255.0 ! interface Vlan2 nameif outside security-level 0 ip address 208.74.158.58 255.255.255.252 ! ftp mode passive access-list inside_nat0_outbound extended permit ip any 10.10.10.0 255.255.255.128 access-list inside_nat0_outbound extended permit ip 192.168.30.0 255.255.255.0 192.168.30.192 255.255.255.192 access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.30.0 255.255.255.0 access-list DefaultRAGroup_splitTunnelAcl_1 standard permit 192.168.30.0 255.255.255.0 pager lines 24 logging asdm informational mtu inside 1500 mtu outside 1500 ip local pool LANVPNPOOL 192.168.30.220-192.168.30.249 mask 255.255.255.0 icmp unreachable rate-limit 1 burst-size 1 no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 192.168.30.0 255.255.255.0 route outside 0.0.0.0 0.0.0.0 208.74.158.57 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy http server enable http 192.168.30.0 255.255.255.0 inside snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 TRANS_ESP_3DES_SHA crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 10 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet timeout 5 ssh timeout 5 console timeout 0 dhcpd auto_config outside ! threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept webvpn group-policy DefaultRAGroup internal group-policy DefaultRAGroup attributes dns-server value 192.168.30.3 vpn-tunnel-protocol l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl_1 username user password Cj7W5X7wERleAewO8ENYtg== nt-encrypted privilege 0 tunnel-group DefaultRAGroup general-attributes address-pool LANVPNPOOL default-group-policy DefaultRAGroup tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group DefaultRAGroup ppp-attributes no authentication chap authentication ms-chap-v2 ! class-map inspection_default match default-inspection-traffic ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum client auto message-length maximum 512 policy-map global_policy class inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect rsh inspect rtsp inspect esmtp inspect sqlnet inspect skinny inspect sunrpc inspect xdmcp inspect sip inspect netbios inspect tftp inspect ip-options ! service-policy global_policy global prompt hostname context : end

    Read the article

  • Does Microsoft still sell FAST ESP?

    - by Kunal Sen
    I wanted some information about FAST ESP search engine. After failing to get any response from the email query system on Microsoft site I called their ore-sales phone number. The person there told me the only way they sell FAST ESP is as a bundled product with SharePoint. That really does not make any sense and contradicts all the PDF documents they have about FAST ESP on their site. Does anyone know who to contact at Microsoft to discuss this product?

    Read the article

  • Fast Esp Custom Stage Development

    - by user363610
    Hi, I am working on Enterprise Search and we are using Fast ESP and for now i have 4 projects but i have no information about stages and python. But i realize that i have learn custom stage development. Because we have a lot of difficulties about document processing. I want to know how can i develop custom stage and especially i wanna know about how i can find Attributefilter stage source code. I am waiting your answers

    Read the article

  • Beginner learning assembly preserving esp after function calls

    - by Daniel
    I'm a beginner learning some assembly, when preserving the ESP register before a function call does it matter if you do it by adding or subtracting? hard to explain, consider the following mov esi, esp sub esp, 12 // on 32bit OS this would mean that there are 3 arguments to the function // push, function call etc cmp esi, esp // should be the same or mov esi, esp // push, function call etc add esp, 12 cmp esi, esp // should be the same Also if for some reason the cmp fails, is it safe to do mov esp, esi to re-align the stack? Thanks EDIT: Also how come i need to do this for a call like sprintf, but MessageBox seems to fix ESP for me? How am i to know what function needs this and what doesn't?

    Read the article

  • Cisco ASA: How to route PPPoE-assigned subnet?

    - by Martijn Heemels
    We've just received a fiber uplink, and I'm trying to configure our Cisco ASA 5505 to properly use it. The provider requires us to connect via PPPoE, and I managed to configure the ASA as a PPPoE client and establish a connection. The ASA is assigned an IP address by PPPoE, and I can ping out from the ASA to the internet, but I should have access to an entire /28 subnet. I can't figure out how to get that subnet configured on the ASA, so that I can route or NAT the available public addresses to various internal hosts. My assigned range is: 188.xx.xx.176/28 The address I get via PPPoE is 188.xx.xx.177/32, which according to our provider is our Default Gateway address. They claim the subnet is correctly routed to us on their side. How does the ASA know which range it is responsible for on the Fiber interface? How do I use the addresses from my range? To clarify my config; The ASA is currently configured to default-route to our ADSL uplink on port Ethernet0/0 (interface vlan2, nicknamed Outside). The fiber is connected to port Ethernet0/2 (interface vlan50, nicknamed Fiber) so I can configure and test it before making it the default route. Once I'm clear on how to set it all up, I'll fully replace the Outside interface with Fiber. My config (rather long): : Saved : ASA Version 8.3(2)4 ! hostname gw domain-name example.com enable password ****** encrypted passwd ****** encrypted names name 10.10.1.0 Inside-dhcp-network description Desktops and clients that receive their IP via DHCP name 10.10.0.208 svn.example.com description Subversion server name 10.10.0.205 marvin.example.com description LAMP development server name 10.10.0.206 dns.example.com description DNS, DHCP, NTP ! interface Vlan2 description Old ADSL WAN connection nameif outside security-level 0 ip address 192.168.1.2 255.255.255.252 ! interface Vlan10 description LAN vlan 10 Regular LAN traffic nameif inside security-level 100 ip address 10.10.0.254 255.255.0.0 ! interface Vlan11 description LAN vlan 11 Lab/test traffic nameif lab security-level 90 ip address 10.11.0.254 255.255.0.0 ! interface Vlan20 description LAN vlan 20 ISCSI traffic nameif iscsi security-level 100 ip address 10.20.0.254 255.255.0.0 ! interface Vlan30 description LAN vlan 30 DMZ traffic nameif dmz security-level 50 ip address 10.30.0.254 255.255.0.0 ! interface Vlan40 description LAN vlan 40 Guests access to the internet nameif guests security-level 50 ip address 10.40.0.254 255.255.0.0 ! interface Vlan50 description New WAN Corporate Internet over fiber nameif fiber security-level 0 pppoe client vpdn group KPN ip address pppoe ! interface Ethernet0/0 switchport access vlan 2 speed 100 duplex full ! interface Ethernet0/1 switchport trunk allowed vlan 10,11,30,40 switchport trunk native vlan 10 switchport mode trunk ! interface Ethernet0/2 switchport access vlan 50 speed 100 duplex full ! interface Ethernet0/3 shutdown ! interface Ethernet0/4 shutdown ! interface Ethernet0/5 switchport access vlan 20 ! interface Ethernet0/6 shutdown ! interface Ethernet0/7 shutdown ! boot system disk0:/asa832-4-k8.bin ftp mode passive clock timezone CEST 1 clock summer-time CEDT recurring last Sun Mar 2:00 last Sun Oct 3:00 dns domain-lookup inside dns server-group DefaultDNS name-server dns.example.com domain-name example.com same-security-traffic permit inter-interface same-security-traffic permit intra-interface object network inside-net subnet 10.10.0.0 255.255.0.0 object network svn.example.com host 10.10.0.208 object network marvin.example.com host 10.10.0.205 object network lab-net subnet 10.11.0.0 255.255.0.0 object network dmz-net subnet 10.30.0.0 255.255.0.0 object network guests-net subnet 10.40.0.0 255.255.0.0 object network dhcp-subnet subnet 10.10.1.0 255.255.255.0 description DHCP assigned addresses on Vlan 10 object network Inside-vpnpool description Pool of assignable addresses for VPN clients object network vpn-subnet subnet 10.10.3.0 255.255.255.0 description Address pool assignable to VPN clients object network dns.example.com host 10.10.0.206 description DNS, DHCP, NTP object-group service iscsi tcp description iscsi storage traffic port-object eq 3260 access-list outside_access_in remark Allow access from outside to HTTP on svn. access-list outside_access_in extended permit tcp any object svn.example.com eq www access-list Insiders!_splitTunnelAcl standard permit 10.10.0.0 255.255.0.0 access-list iscsi_access_in remark Prevent disruption of iscsi traffic from outside the iscsi vlan. access-list iscsi_access_in extended deny tcp any interface iscsi object-group iscsi log warnings ! snmp-map DenyV1 deny version 1 ! pager lines 24 logging enable logging timestamp logging asdm-buffer-size 512 logging monitor warnings logging buffered warnings logging history critical logging asdm errors logging flash-bufferwrap logging flash-minimum-free 4000 logging flash-maximum-allocation 2000 mtu outside 1500 mtu inside 1500 mtu lab 1500 mtu iscsi 9000 mtu dmz 1500 mtu guests 1500 mtu fiber 1492 ip local pool DHCP_VPN 10.10.3.1-10.10.3.20 mask 255.255.0.0 ip verify reverse-path interface outside no failover icmp unreachable rate-limit 10 burst-size 5 asdm image disk0:/asdm-635.bin asdm history enable arp timeout 14400 nat (inside,outside) source static any any destination static vpn-subnet vpn-subnet ! object network inside-net nat (inside,outside) dynamic interface object network svn.example.com nat (inside,outside) static interface service tcp www www object network lab-net nat (lab,outside) dynamic interface object network dmz-net nat (dmz,outside) dynamic interface object network guests-net nat (guests,outside) dynamic interface access-group outside_access_in in interface outside access-group iscsi_access_in in interface iscsi route outside 0.0.0.0 0.0.0.0 192.168.1.1 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 dynamic-access-policy-record DfltAccessPolicy aaa-server SBS2003 protocol radius aaa-server SBS2003 (inside) host 10.10.0.204 timeout 5 key ***** aaa authentication enable console SBS2003 LOCAL aaa authentication ssh console SBS2003 LOCAL aaa authentication telnet console SBS2003 LOCAL http server enable http 10.10.0.0 255.255.0.0 inside snmp-server host inside 10.10.0.207 community ***** version 2c snmp-server location Server room snmp-server contact [email protected] snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart snmp-server enable traps syslog crypto ipsec transform-set TRANS_ESP_AES-256_SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set TRANS_ESP_AES-256_SHA mode transport crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto dynamic-map outside_dyn_map 20 set pfs group5 crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_AES-256_SHA crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5 crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption 3des hash sha group 2 lifetime 86400 telnet 10.10.0.0 255.255.0.0 inside telnet timeout 5 ssh scopy enable ssh 10.10.0.0 255.255.0.0 inside ssh timeout 5 ssh version 2 console timeout 30 management-access inside vpdn group KPN request dialout pppoe vpdn group KPN localname INSIDERS vpdn group KPN ppp authentication pap vpdn username INSIDERS password ***** store-local dhcpd address 10.40.1.0-10.40.1.100 guests dhcpd dns 8.8.8.8 8.8.4.4 interface guests dhcpd update dns interface guests dhcpd enable guests ! threat-detection basic-threat threat-detection scanning-threat threat-detection statistics host number-of-rate 2 threat-detection statistics port number-of-rate 3 threat-detection statistics protocol number-of-rate 3 threat-detection statistics access-list threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200 ntp server dns.example.com source inside prefer webvpn group-policy DfltGrpPolicy attributes vpn-tunnel-protocol IPSec l2tp-ipsec group-policy Insiders! internal group-policy Insiders! attributes wins-server value 10.10.0.205 dns-server value 10.10.0.206 vpn-tunnel-protocol IPSec l2tp-ipsec split-tunnel-policy tunnelspecified split-tunnel-network-list value Insiders!_splitTunnelAcl default-domain value example.com username martijn password ****** encrypted privilege 15 username marcel password ****** encrypted privilege 15 tunnel-group DefaultRAGroup ipsec-attributes pre-shared-key ***** tunnel-group Insiders! type remote-access tunnel-group Insiders! general-attributes address-pool DHCP_VPN authentication-server-group SBS2003 LOCAL default-group-policy Insiders! tunnel-group Insiders! ipsec-attributes pre-shared-key ***** ! class-map global-class match default-inspection-traffic class-map type inspect http match-all asdm_medium_security_methods match not request method head match not request method post match not request method get ! ! policy-map type inspect dns preset_dns_map parameters message-length maximum 512 policy-map type inspect http http_inspection_policy parameters protocol-violation action drop-connection policy-map global-policy class global-class inspect dns inspect esmtp inspect ftp inspect h323 h225 inspect h323 ras inspect http inspect icmp inspect icmp error inspect mgcp inspect netbios inspect pptp inspect rtsp inspect snmp DenyV1 ! service-policy global-policy global smtp-server 123.123.123.123 prompt hostname context call-home profile CiscoTAC-1 no active destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService destination address email [email protected] destination transport-method http subscribe-to-alert-group diagnostic subscribe-to-alert-group environment subscribe-to-alert-group inventory periodic monthly subscribe-to-alert-group configuration periodic monthly subscribe-to-alert-group telemetry periodic daily hpm topN enable Cryptochecksum:a76bbcf8b19019771c6d3eeecb95c1ca : end asdm image disk0:/asdm-635.bin asdm location svn.example.com 255.255.255.255 inside asdm location marvin.example.com 255.255.255.255 inside asdm location dns.example.com 255.255.255.255 inside asdm history enable

    Read the article

  • Extracting dates from html meta data in FAST-ESP

    - by Neil
    During document processing I want to extract all dates from html meta data and then identify the latest date which will be used to populate a date field (dtgeneric1). <meta name="OriginalPublicationDate" content="2010/04/21 12:06:36" /> <meta name="LastModificationDate" content="2010/04/22 14:10:16" /> + other non-date meta data Inspection using spy stages shows that our pipeline already adds meta_* attributes but the meta data names will be different across documents from different sources. #### ATTRIBUTE meta_originalpublicationdate <class 'docproc.DocumentAttributes.TextChunks'>: 2010/04/21 12:06:36 #### ATTRIBUTE meta_lastmodificationdate <class 'docproc.DocumentAttributes.TextChunks'>: 2010/04/22 14:10:16 + other non-date meta attributes Ideally we would like to pass all the meta_* attributes to a Python stage and use that to work out which are dates and which is the largest but there seems to be no way of specifying "all meta attributes" as input. Has anyone done something similar and can offer any advice on the best way to do this. Thanks Neil

    Read the article

  • Storing index values in FAST-ESP without modifications

    - by Abel Morelos
    Hi, first of all I'm totally new to FAST but I already have a couple of issues I need to solve, so I'm sorry if my questions are very basic =) Well, the problem is that I have a field in the FAST index which in the source document is something like "ABC 12345" (please note the intentional whitespaces) but when stored in the index is in the form "ABC 123456" (please note that now there is a single space). If I retrieve all the document values then this specific value is OK (with all the whitespaces), my only problem is with the way the value is stored in the index since I need to retrieve and display it to my user just like it appears in the original document, and I don't want to go to the full document just for this value, I want the value that I already have in the index. I think I need to update one of the FAST XML configuration files but I don't have enough documentation at hand in order to decide where to perform the change, index_profile.xml? in the XMLMapper file?

    Read the article

  • ASA 5540 v8.4(3) vpn to ASA 5505 v8.2(5), tunnel up but I cant ping from 5505 to IP on other side

    - by user223833
    I am having problems pinging from a 5505(remote) to IP 10.160.70.10 in the network behind the 5540(HQ side). 5505 inside IP: 10.56.0.1 Out: 71.43.109.226 5540 Inside: 10.1.0.8 out: 64.129.214.27 I Can ping from 5540 to 5505 inside 10.56.0.1. I also ran ASDM packet tracer in both directions, it is ok from 5540 to 5505, but drops the packet from 5505 to 5540. It gets through the ACL and dies at the NAT. Here is the 5505 config, I am sure it is something simple I am missing. ASA Version 8.2(5) ! hostname ASA-CITYSOUTHDEPOT domain-name rngint.net names ! interface Ethernet0/0 switchport access vlan 2 ! interface Ethernet0/1 ! interface Ethernet0/2 ! interface Ethernet0/3 ! interface Ethernet0/4 ! interface Ethernet0/5 ! interface Ethernet0/6 ! interface Ethernet0/7 ! interface Vlan1 nameif inside security-level 100 ip address 10.56.0.1 255.255.0.0 ! interface Vlan2 nameif outside security-level 0 ip address 71.43.109.226 255.255.255.252 ! banner motd ***ASA-CITYSOUTHDEPOT*** banner asdm CITY SOUTH DEPOT ASA5505 ftp mode passive clock timezone EST -5 clock summer-time EDT recurring dns server-group DefaultDNS domain-name rngint.net access-list outside_1_cryptomap extended permit ip host 71.43.109.226 host 10.1.0.125 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.0.0.0 255.0.0.0 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.106.70.0 255.255.255.0 access-list outside_1_cryptomap extended permit ip 10.56.0.0 255.255.0.0 10.106.130.0 255.255.255.0 access-list outside_1_cryptomap extended permit ip host 71.43.109.226 host 10.160.70.10 access-list inside_nat0_outbound extended permit ip host 71.43.109.226 host 10.1.0.125 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.0.0.0 255.0.0.0 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.106.130.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip 10.56.0.0 255.255.0.0 10.106.70.0 255.255.255.0 access-list inside_nat0_outbound extended permit ip host 71.43.109.226 10.106.70.0 255.255.255.0 pager lines 24 logging enable logging buffer-size 25000 logging buffered informational logging asdm warnings mtu inside 1500 mtu outside 1500 icmp unreachable rate-limit 1 burst-size 1 icmp permit any inside no asdm history enable arp timeout 14400 global (outside) 1 interface nat (inside) 0 access-list inside_nat0_outbound nat (inside) 1 0.0.0.0 0.0.0.0 route outside 0.0.0.0 0.0.0.0 71.43.109.225 1 timeout xlate 3:00:00 timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02 timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00 timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00 timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute timeout tcp-proxy-reassembly 0:01:00 timeout floating-conn 0:00:00 dynamic-access-policy-record DfltAccessPolicy aaa-server TACACS+ protocol tacacs+ aaa-server TACACS+ (inside) host 10.106.70.36 key ***** aaa authentication http console LOCAL aaa authentication ssh console LOCAL aaa authorization exec authentication-server http server enable http 192.168.1.0 255.255.255.0 inside http 10.0.0.0 255.0.0.0 inside http 0.0.0.0 0.0.0.0 outside snmp-server host inside 10.106.70.7 community ***** no snmp-server location no snmp-server contact snmp-server community ***** snmp-server enable traps snmp authentication linkup linkdown coldstart crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map outside_map 1 match address outside_1_cryptomap crypto map outside_map 1 set pfs group1 crypto map outside_map 1 set peer 64.129.214.27 crypto map outside_map 1 set transform-set ESP-3DES-SHA crypto map outside_map interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption des hash md5 group 2 lifetime 86400 telnet timeout 5 ssh 10.0.0.0 255.0.0.0 inside ssh 0.0.0.0 0.0.0.0 outside ssh timeout 5 console timeout 0 management-access inside dhcpd auto_config outside ! dhcpd address 10.56.0.100-10.56.0.121 inside dhcpd dns 10.1.0.125 interface inside dhcpd auto_config outside interface inside ! dhcprelay server 10.1.0.125 outside dhcprelay enable inside dhcprelay setroute inside dhcprelay timeout 60 threat-detection basic-threat threat-detection statistics access-list no threat-detection statistics tcp-intercept tftp-server inside 10.1.1.25 CITYSOUTHDEPOT-ASA-Confg webvpn tunnel-group 64.129.214.27 type ipsec-l2l tunnel-group 64.129.214.27 ipsec-attributes pre-shared-key ***** ! ! prompt hostname context

    Read the article

  • What Counts For A DBA: ESP

    - by Louis Davidson
    Now I don’t want to get religious here, and I’m not going to, but what I’m going to describe in this ‘What Counts for a DBA’ installment sometimes feels like magic. Often  I will spend hours thinking about the solution to a design issue or coding problem, working diligently to try to come up with a solution and then finally just give up with the feeling that I’m not even qualified to be a data entry clerk, much less a data architect.  At this point I often take a walk (or sometimes a nap), and then it hits me. I realize that I have the answer just sitting in my brain, ready to implement.  This phenomenon is not limited to walks either; it can happen almost any time after I stop my obsession about a problem. I call this phenomena ESP (or Extra-Sensory Programming.)  Another term for this could be ‘sleeping on it’, and while the idiom tends to mean to let time pass to actively think about a problem, sleeping on a problem also lets you relax and let your brain do the work. I first noticed this back in my college days when I would play video games for hours on end. We would get stuck deep in some dungeon unable to find a way out, playing for days on end until we were beaten down tired. Once we gave up and walked away, the solution would usually be there waiting for one of us before we came back to play the next day.  Sometimes it would be in the form of a dream, and sometimes it would just be that the problem was now easy to solve when we started to play again.  While it worked great for video games, it never occurred when I studied English Literature for hours on end, or even when I worked for the same sort of frustrating hours attempting to solve a homework problem in Calculus.  I believe that the difference was that I was passionate about the video game, and certainly far less so about homework where people used the word “thou” instead of “you” or x to represent a number. This phenomenon occurs somewhat more often in my current work as a professional data programmer, because I am very passionate about SQL and love those aspects of my career choice.  Every day that I get to draw a new data model to solve a customer issue, or write a complex SELECT statement to ferret out the answer to a complex data question, is a great day. I hope it is the same for any reader of this blog.  But, unfortunately, while the day on a whole is great, a heck of a lot of noise is generated in work life. There are the typical project deadlines, along with the requisite project manager sitting on your shoulders shouting slogans to try to make you to go faster: Add in office politics, and the occasional family issues that permeate the mind, and you lose the ability to think deeply about any problem, not to mention occasionally forgetting your own name.  These office realities coupled with a difficult SQL problem staring at you from your widescreen monitor will slowly suck the life force out of your body, making it seem impossible to solve the problem This is when the walk starts; or a nap. Maybe you hide from the madness under your desk like George Costanza hides from Steinbrenner on Seinfeld.  Forget about the problem. Free your mind from the insanity of the problem and your surroundings. Then let your training and education deep in your brain take over and see if it will passively do the rest for you. If you don’t end up with a solution, the worst case scenario is that you have a bit of exercise or rest, and you won’t have heard the phrase “better is the enemy of good enough” even once…which certainly will do your brain some good. Once you stop expecting whipping your brain for information, inspiration may just strike and instead of a humdrum solution you find a solution you hadn’t even considered, almost magically. So, my beloved manager, next time you have an urgent deadline and you come across me taking a nap, creep away quietly because I’m working, doing some extra-sensory programming.

    Read the article

  • How can I know what this does?

    - by Dabor Troppe
    I got this piece of Assembly code extracted from some piece of software, but unfortunately I don't know anything of assembler and the bits I touched of Assembler was back in the Commodore Amiga with the 68000. Can anybody guide me on how I could understand this code without me needing to learn assembler from scratch, or just tell me what it does? Is there any kind of "Simulator" out there that I can run this on to see what it does? -[ObjSample Param1:andParam2:]: 00000c79 pushl %ebp 00000c7a movl %esp,%ebp 00000c7c subl $0x48,%esp 00000c7f movl %ebx,0xf4(%ebp) 00000c82 movl %esi,0xf8(%ebp) 00000c85 movl %edi,0xfc(%ebp) 00000c88 calll 0x00000c8d 00000c8d popl %ebx 00000c8e cmpb $-[ObjSample delegate],_bDoOnce.26952-0xc8d(%ebx) 00000c95 jel 0x00000d47 00000c9b movb $-[ObjSample delegate],_bDoOnce.26952-0xc8d(%ebx) 00000ca2 movl 0x7dc0-0xc8d(%ebx),%eax 00000ca8 movl %eax,0x04(%esp) 00000cac movl 0x7df4-0xc8d(%ebx),%eax 00000cb2 movl %eax,(%esp) 00000cb5 calll _objc_msgSend 00000cba movl 0x7dbc-0xc8d(%ebx),%edx 00000cc0 movl %edx,0x04(%esp) 00000cc4 movl %eax,(%esp) 00000cc7 calll _objc_msgSend 00000ccc movl %eax,0xe4(%ebp) 00000ccf movl 0x7db8-0xc8d(%ebx),%eax 00000cd5 movl %eax,0x04(%esp) 00000cd9 movl 0xe4(%ebp),%eax 00000cdc movl %eax,(%esp) 00000cdf calll _objc_msgSend 00000ce4 leal (%eax,%eax),%edi 00000ce7 movl %edi,(%esp) 00000cea calll _malloc 00000cef movl %eax,%esi 00000cf1 movl %edi,0x08(%esp) 00000cf5 movl $-[ObjSample delegate],0x04(%esp) 00000cfd movl %eax,(%esp) 00000d00 calll _memset 00000d05 movl $0x00000004,0x10(%esp) 00000d0d movl %edi,0x0c(%esp) 00000d11 movl %esi,0x08(%esp) 00000d15 movl 0x7db4-0xc8d(%ebx),%eax 00000d1b movl %eax,0x04(%esp) 00000d1f movl 0xe4(%ebp),%eax 00000d22 movl %eax,(%esp) 00000d25 calll _objc_msgSend 00000d2a xorl %edx,%edx 00000d2c movl %edi,%eax 00000d2e shrl $0x03,%eax 00000d31 jmp 0x00000d34 00000d33 incl %edx 00000d34 cmpl %edx,%eax 00000d36 ja 0x00000d33 00000d38 movl %esi,(%esp) 00000d3b calll _free 00000d40 movb $0x01,_isAuthenticated-0xc8d(%ebx) 00000d47 movzbl _isAuthenticated-0xc8d(%ebx),%eax 00000d4e movl 0xf4(%ebp),%ebx 00000d51 movl 0xf8(%ebp),%esi 00000d54 movl 0xfc(%ebp),%edi 00000d57 leave 00000d58 ret

    Read the article

  • C to Assembly code - what does it mean

    - by Smith
    I'm trying to figure out exactly what is going on with the following assembly code. Can someone go down line by line and explain what is happening? I input what I think is happening (see comments) but need clarification. .file "testcalc.c" .section .rodata.str1.1,"aMS",@progbits,1 .LC0: .string "x=%d, y=%d, z=%d, result=%d\n" .text .globl main .type main, @function main: leal 4(%esp), %ecx // establish stack frame andl $-16, %esp // decrement %esp by 16, align stack pushl -4(%ecx) // push original stack pointer pushl %ebp // save base pointer movl %esp, %ebp // establish stack frame pushl %ecx // save to ecx subl $36, %esp // alloc 36 bytes for local vars movl $11, 8(%esp) // store 11 in z movl $6, 4(%esp) // store 6 in y movl $2, (%esp) // store 2 in x call calc // function call to calc movl %eax, 20(%esp) // %esp + 20 into %eax movl $11, 16(%esp) // WHAT movl $6, 12(%esp) // WHAT movl $2, 8(%esp) // WHAT movl $.LC0, 4(%esp) // WHAT?!?! movl $1, (%esp) // move result into address of %esp call __printf_chk // call printf function addl $36, %esp // WHAT? popl %ecx popl %ebp leal -4(%ecx), %esp ret .size main, .-main .ident "GCC: (Ubuntu 4.3.3-5ubuntu4) 4.3.3" .section .note.GNU-stack,"",@progbits Original code: #include <stdio.h> int calc(int x, int y, int z); int main() { int x = 2; int y = 6; int z = 11; int result; result = calc(x,y,z); printf("x=%d, y=%d, z=%d, result=%d\n",x,y,z,result); }

    Read the article

  • Windows 7 & kodak printer esp 7

    - by Yoraf
    I have bought a new PC with Windows 7 and a Kodak wireless printer esp 7. I can't download the software always unsuccessful and can't connect to my printer. Any suggestions? Edit (from the other, duplicate question): Still having problems with printing. I did get it working by removing 'bonjour' but turned on yesterday and hey presto it's not working again. The printer is installed and showing as disconnected. Any ideas now? The chat doesn't work with Windows 7, I have downloaded the latest version, they take ages to answer emails, need to print stuff urgently. It's driving me insane!! Please help.

    Read the article

  • Email provider - suggestions needed

    - by Christian Fazzini
    We are looking for a good way to have email support. In theory, we need to allow end-users to send emails directly to support and careers. i.e. support@domain_name_here.com and careers@domain_name_here.com. Second, we need to provide emails to our staff. So each staff member has their own email address. i.e. joe@domain_name_here.com, meghan@domain_name_here.com, etc. Google Apps is one that we are considering. However, they are charging $50 per user, per year. Not so bad, considering the quality and the features they offer. However, there are also cheaper alternatives. i.e. my domain registrar offers an email plan for $20 / year / 10 emails. Go Daddy has a number of plans and still a lot more affordable than Google Apps. So far Namecheap and Go Daddy are the only ones I have looked at for email plans. Is it worth signing up with Google Apps? Or are there better alternatives? Your thoughts?

    Read the article

  • Grails gdoc editor support (esp IntelliJ)

    - by Stefan
    Since Grails 1.2 there's a documentation engine included: gdoc. The documentation's syntax is based on the Textile format. Is there some editor support for this? My first choice would be a plugin for IntelliJ, second option on for vim or gedit. Any hints welcome. I am totally a aware that the format is very simple by itself but having code coloring and content assist would be really nice.

    Read the article

  • Help with Kodak esp 3250 printer driver on Lubuntu 12.1 SOLVED!

    - by user108608
    First my system: pentium 4 -don't remember the speed-, 1g ram, dual boot to separate physical drives, Fdos and Lubuntu 12.1 second my lan: I have four computers operating for the same printer. 1. Intel quad core i5, 4g ram, running Windoze 7 64 bit, printer connected and shared from here. Kodak ESP 3250 2. Gateway 17" laptop running Windoze 7 32bit 3. Asus tablet (small laptop) running Lumbutu 12.1 4. My dual boot system running Fdos and Lubuntu 12.1 The problem: I downloaded c2esp_25c-1_i386.deb, tried to install it using DEBI Package Installer, it loads the files, looks for cups driver and ends with an error: "Dependancy is not satisfiable: libcupsdriver1 (=1.4.0)" What do I do now? Is there some place that I can get the correct cups driver? further information: The Asus tablet was running Ubuntu 12.1 (very slowly and with a few crashes) and could print from the lan printer with no problems. Is there something in Ubuntu that can be loaded into Lubuntu? noobee user hoping for answers, Paul

    Read the article

  • How do I install a driver for a Kodak esp 3250 printer?

    - by user108608
    First my system: pentium 4 -don't remember the speed-, 1g ram, dual boot to separate physical drives, Fdos and Lubuntu 12.1 second my lan: I have four computers operating for the same printer. Intel quad core i5, 4g ram, running Windoze 7 64 bit, printer connected and shared from here. Kodak ESP 3250 Gateway 17" laptop running Windoze 7 32bit Asus tablet (small laptop) running Lumbutu 12.1 My dual boot system running Fdos and Lubuntu 12.1 The problem: I downloaded c2esp_25c-1_i386.deb, tried to install it using DEBI Package Installer, it loads the files, looks for cups driver and ends with an error: "Dependancy is not satisfiable: libcupsdriver1 (=1.4.0)" What do I do now? Is there some place that I can get the correct cups driver? further information: The Asus tablet was running Ubuntu 12.1 (very slowly and with a few crashes) and could print from the lan printer with no problems. Is there something in Ubuntu that can be loaded into Lubuntu?

    Read the article

  • Google Analytics - bad experiences? (esp. adult content)

    - by Litso
    Hello all, I work for a rather large adult website, and we're currently not using Google Analytics. There is an internal debate going on about whether we should start using Analytics, but there is hestitation from certain parties. The main argument is that they fear that Google will get too much insight into our website, and might even block us from the index as a result based on our adult content. Has anyone here ever had such an experience, or know stories about bad experiences with Google Analytics in such a manner? I personally think it will only improve our website if we were able to use Analytics, but the dev team was asked to look into possible negative effects. Any help would be appreciated.

    Read the article

  • Google Analytics - bad experiences? (esp. adult content)

    - by Litso
    I work for a rather large adult website, and we're currently not using Google Analytics. There is an internal debate going on about whether we should start using Analytics, but there is hestitation from certain parties. The main argument is that they fear that Google will get too much insight into our website, and might even block us from the index as a result based on our adult content. Has anyone here ever had such an experience, or know stories about bad experiences with Google Analytics in such a manner? I personally think it will only improve our website if we were able to use Analytics, but the dev team was asked to look into possible negative effects. Any help would be appreciated.

    Read the article

  • How to write a buffer-overflow exploit in GCC,windows XP,x86?

    - by Mask
    void function(int a, int b, int c) { char buffer1[5]; char buffer2[10]; int *ret; ret = buffer1 + 12; (*ret) += 8;//why is it 8?? } void main() { int x; x = 0; function(1,2,3); x = 1; printf("%d\n",x); } The above demo is from here: http://insecure.org/stf/smashstack.html But it's not working here: D:\test>gcc -Wall -Wextra hw.cpp && a.exe hw.cpp: In function `void function(int, int, int)': hw.cpp:6: warning: unused variable 'buffer2' hw.cpp: At global scope: hw.cpp:4: warning: unused parameter 'a' hw.cpp:4: warning: unused parameter 'b' hw.cpp:4: warning: unused parameter 'c' 1 And I don't understand why it's 8 though the author thinks: A little math tells us the distance is 8 bytes. My gdb dump as called: Dump of assembler code for function main: 0x004012ee <main+0>: push %ebp 0x004012ef <main+1>: mov %esp,%ebp 0x004012f1 <main+3>: sub $0x18,%esp 0x004012f4 <main+6>: and $0xfffffff0,%esp 0x004012f7 <main+9>: mov $0x0,%eax 0x004012fc <main+14>: add $0xf,%eax 0x004012ff <main+17>: add $0xf,%eax 0x00401302 <main+20>: shr $0x4,%eax 0x00401305 <main+23>: shl $0x4,%eax 0x00401308 <main+26>: mov %eax,0xfffffff8(%ebp) 0x0040130b <main+29>: mov 0xfffffff8(%ebp),%eax 0x0040130e <main+32>: call 0x401b00 <_alloca> 0x00401313 <main+37>: call 0x4017b0 <__main> 0x00401318 <main+42>: movl $0x0,0xfffffffc(%ebp) 0x0040131f <main+49>: movl $0x3,0x8(%esp) 0x00401327 <main+57>: movl $0x2,0x4(%esp) 0x0040132f <main+65>: movl $0x1,(%esp) 0x00401336 <main+72>: call 0x4012d0 <function> 0x0040133b <main+77>: movl $0x1,0xfffffffc(%ebp) 0x00401342 <main+84>: mov 0xfffffffc(%ebp),%eax 0x00401345 <main+87>: mov %eax,0x4(%esp) 0x00401349 <main+91>: movl $0x403000,(%esp) 0x00401350 <main+98>: call 0x401b60 <printf> 0x00401355 <main+103>: leave 0x00401356 <main+104>: ret 0x00401357 <main+105>: nop 0x00401358 <main+106>: add %al,(%eax) 0x0040135a <main+108>: add %al,(%eax) 0x0040135c <main+110>: add %al,(%eax) 0x0040135e <main+112>: add %al,(%eax) End of assembler dump. Dump of assembler code for function function: 0x004012d0 <function+0>: push %ebp 0x004012d1 <function+1>: mov %esp,%ebp 0x004012d3 <function+3>: sub $0x38,%esp 0x004012d6 <function+6>: lea 0xffffffe8(%ebp),%eax 0x004012d9 <function+9>: add $0xc,%eax 0x004012dc <function+12>: mov %eax,0xffffffd4(%ebp) 0x004012df <function+15>: mov 0xffffffd4(%ebp),%edx 0x004012e2 <function+18>: mov 0xffffffd4(%ebp),%eax 0x004012e5 <function+21>: movzbl (%eax),%eax 0x004012e8 <function+24>: add $0x5,%al 0x004012ea <function+26>: mov %al,(%edx) 0x004012ec <function+28>: leave 0x004012ed <function+29>: ret In my case the distance should be - = 5,right?But it seems not working.. Why function needs 56 bytes for local variables?( sub $0x38,%esp )

    Read the article

  • Switch case assembly level code

    - by puffadder
    Hi All, I am programming C on cygwin windows. After having done a bit of C programming and getting comfortable with the language, I wanted to look under the hood and see what the compiler is doing for the code that I write. So I wrote down a code block containing switch case statements and converted them into assembly using: gcc -S foo.c Here is the C source: switch(i) { case 1: { printf("Case 1\n"); break; } case 2: { printf("Case 2\n"); break; } case 3: { printf("Case 3\n"); break; } case 4: { printf("Case 4\n"); break; } case 5: { printf("Case 5\n"); break; } case 6: { printf("Case 6\n"); break; } case 7: { printf("Case 7\n"); break; } case 8: { printf("Case 8\n"); break; } case 9: { printf("Case 9\n"); break; } case 10: { printf("Case 10\n"); break; } default: { printf("Nothing\n"); break; } } Now the resultant assembly for the same is: movl $5, -4(%ebp) cmpl $10, -4(%ebp) ja L13 movl -4(%ebp), %eax sall $2, %eax movl L14(%eax), %eax jmp *%eax .section .rdata,"dr" .align 4 L14: .long L13 .long L3 .long L4 .long L5 .long L6 .long L7 .long L8 .long L9 .long L10 .long L11 .long L12 .text L3: movl $LC0, (%esp) call _printf jmp L2 L4: movl $LC1, (%esp) call _printf jmp L2 L5: movl $LC2, (%esp) call _printf jmp L2 L6: movl $LC3, (%esp) call _printf jmp L2 L7: movl $LC4, (%esp) call _printf jmp L2 L8: movl $LC5, (%esp) call _printf jmp L2 L9: movl $LC6, (%esp) call _printf jmp L2 L10: movl $LC7, (%esp) call _printf jmp L2 L11: movl $LC8, (%esp) call _printf jmp L2 L12: movl $LC9, (%esp) call _printf jmp L2 L13: movl $LC10, (%esp) call _printf L2: Now, in the assembly, the code is first checking the last case (i.e. case 10) first. This is very strange. And then it is copying 'i' into 'eax' and doing things that are beyond me. I have heard that the compiler implements some jump table for switch..case. Is it what this code is doing? Or what is it doing and why? Because in case of less number of cases, the code is pretty similar to that generated for if...else ladder, but when number of cases increases, this unusual-looking implementation is seen. Thanks in advance.

    Read the article

  • Cisco ASA dropping IPsec VPN between istself and CentOS server

    - by sebelk
    Currently we're trying to set up an IPsec VPN between a Cisco ASA Version 8.0(4) and a CentOS Linux server. The tunnel comes up successfully, but for some reason that we can't figure out, the firewall is dropping packets from the VPN. The IPsec settings in the ASA sre as follows: crypto ipsec transform-set up-transform-set esp-3des esp-md5-hmac crypto ipsec transform-set up-transform-set2 esp-3des esp-sha-hmac crypto ipsec transform-set up-transform-set3 esp-aes esp-md5-hmac crypto ipsec transform-set up-transform-set4 esp-aes esp-sha-hmac crypto ipsec security-association lifetime seconds 28800 crypto ipsec security-association lifetime kilobytes 4608000 crypto map linuxserver 10 match address filtro-encrypt-linuxserver crypto map linuxserver 10 set peer linuxserver crypto map linuxserver 10 set transform-set up-transform-set2 up-transform-set3 up-transform-set4 crypto map linuxserver 10 set security-association lifetime seconds 28800 crypto map linuxserver 10 set security-association lifetime kilobytes 4608000 crypto map linuxserver interface outside crypto isakmp enable outside crypto isakmp policy 1 authentication pre-share encryption aes hash sha group 2 lifetime 28800 crypto isakmp policy 2 authentication pre-share encryption aes-256 hash sha group 2 lifetime 86400 crypto isakmp policy 3 authentication pre-share encryption aes-256 hash md5 group 2 lifetime 86400 crypto isakmp policy 4 authentication pre-share encryption aes-192 hash sha group 2 lifetime 86400 crypto isakmp policy 5 authentication pre-share encryption aes-192 hash md5 group 2 group-policy linuxserverip internal group-policy linuxserverip attributes vpn-filter value filtro-linuxserverip tunnel-group linuxserverip type ipsec-l2l tunnel-group linuxserverip general-attributes default-group-policy linuxserverip tunnel-group linuxserverip ipsec-attributes pre-shared-key * Does anyone know where the problem is and how to fix it?

    Read the article

  • "call" instruction that seemingly jumps into itself

    - by Checkers
    I have gcc 4 compiling some C++ code into the following (from objdump): 00000030 <func()>: 30: 55 push %ebp 31: 89 e5 mov %esp,%ebp 33: 56 push %esi 34: 31 f6 xor %esi,%esi 36: 53 push %ebx 37: bb 00 00 00 00 mov $0x0,%ebx 3c: 83 ec 40 sub $0x40,%esp 3f: c7 04 24 01 00 00 00 movl $0x1,(%esp) 46: e8 fc ff ff ff call 47 <func()+0x17> 4b: 8d 55 ec lea 0xffffffec(%ebp),%edx 4e: 89 14 24 mov %edx,(%esp) 51: 89 5c 24 04 mov %ebx,0x4(%esp) 55: 89 74 24 08 mov %esi,0x8(%esp) 59: 89 44 24 0c mov %eax,0xc(%esp) ; the rest of the function is omitted I can't understand the operand of call instruction here, why does it call into itself, but with one byte off?

    Read the article

1 2 3 4 5 6 7 8 9 10 11 12  | Next Page >