Search Results

Search found 5367 results on 215 pages for 'devices'.

Page 121/215 | < Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >

  • Linux WD30EZRX WD Green HDD & Blacx Duet 5G Usb

    - by Adam
    I have connected up an WD30EZRX WD Green HDD to a Thermaltake Blacx Duet 5G USB dock in Ubuntu 12.04. Every thing seems fine except when the HDD idles it seems to have error ls: reading directory .: Input/output error after a while and is only fixed by unmounting and remounting the drive as root. I have the following line in /etc/fstab UUID=AAF670E9F670B6E3 /media/3TB ntfs defaults,user,auto 0 0 I have noticed that it seems to go between /dev/sdc2 and /dev/sdd2 devices on remount. I did copy 1TB last night without issue in 1 sitting. But after x mins of idle it has remount issue. Any tips/suggestions on how to proceed would be appreciated. Spent most of the night googling and all its done is made me sad. Edit (tried as suggested): root@mediaserver:/media/3TB# sudo hdparm -B 255 -S 253 /dev/sdd2 /dev/sdd2: setting Advanced Power Management level to disabled HDIO_DRIVE_CMD failed: Input/output error setting standby to 253 (vendor-specific) APM_level = not supported Seems as if that didn't help with this particular drive.

    Read the article

  • Computer Components

    - by Martin
    What is the role of a motherboard in terms of how components communicate with the processor (via the system busses). Therefore, for each component, which communication bus is involved and what is the route that data takes from the component to the processor, including; The bus name Whether bus is serial or parallel The name of any bridges involved Also, what is the the role of a bridge The components are: Internal components: Floppy Drive, Hard Drive, CD/DVD Drive, Memory, Processor Power supply, Graphics card & Sound card External devices: Monitor, Keyboard, Mouse (PS2 & USB), Printer, Pen Drive I have absolutely no idea of what the routes are and how motherboards communicate, could someone give me a start here? Thanks.

    Read the article

  • MAC to IP binding in ASA 5510 / SG 300-52

    - by Sampsa
    I am trying to configure a Cisco ASA 5510 to assign specific IP-addresses to specific MACs. Firmware on my ASA is 8.2(5). I have used this feature in our previous device (Cisco SA-520W). I have also read that this feature is (not yet) implemented. How do I work around this problem, if not by direct assignment? Do I need to specify fixed IP's on concerned devices themselves? I also have a SG 300-52 switch for our LAN. We cannot specify IP-addresses to ports, because we have further switches down the line. Thank you for your help!

    Read the article

  • KVM Virtual guest Paused on Reboot

    - by David Hamilton
    I'm running REHL 6 and just installed a Ubuntu Server Guest via KVM set to start at boot. This works correctly and the guest loads, but it loads "paused" and requires that I manually un-pause it. Can someone give me a hint as to how I can I get the Guest OS to actually become active on boot? Here is the libvert dump as requested...Also tried libvert auto-start --- no effect. <domain type='kvm' id='1'> <name>MailServer</name> <uuid>a61dae75-1f5c-d536-718f-3c615d9b4868</uuid> <memory>4194304</memory> <currentMemory>4194304</currentMemory> <vcpu>4</vcpu> <os> <type arch='x86_64' machine='rhel6.0.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='none'/> <source file='/home/MailServer/MailServer-1.img'/> <target dev='hda' bus='ide'/> <alias name='ide0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> <alias name='ide0-1-0'/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <alias name='ide0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:cd:f9:9f'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/1'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='5900' autoport='yes'/> <sound model='ac97'> <alias name='sound0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </sound> <video> <model type='cirrus' vram='9216' heads='1'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='selinux'> <label>system_u:system_r:svirt_t:s0:c211,c271</label> <imagelabel>system_u:object_r:svirt_image_t:s0:c211,c271</imagelabel> </seclabel></domain>

    Read the article

  • How to create a virtual input in windows from an audio stream

    - by Brian
    Great to find this forum full of knowledge. I was wondering if anyone knew of an application or other work around to create a virtual input device in windows. I have a IP cam app on my android phone, that I would like to use for skype webcam. It comes with a port for getting the video feed into skype, and that works great. However, the only audio available, is a OGG stream. Both video and audio work great with media players such as VLC etc, but ot with skype, since skype only works with windows input devices. Is there such software outthere, in which I could simply name my audio stream address, and pipe that to a virtual input device to allow skype to find it?

    Read the article

  • 2 x Netgear GS724T (Dual GBIC) trunking issue

    - by Arthor
    I have the following: Netgear GS724T (Firmware Version V1.0.3_35, Protocol Version - 2.001.002) 4 x Indineon ISFP GBR/FC Settings STP Function - Enabled Fast Link - Enabled Trunking port 23,24, (21,22 - RJ45 cables, but not connected.) I have connected both switches via 2 fiber cables and want to use trunking. The problem I am having. Sometimes I get a an issue when none of the switches cannot talk with each other, nor the devices, sometime they can. The problem is irregular and no patten can be determined The statistics shows that when the switches does not work, they have RX errors If I remove one to the GBIC connections, then everything works as normal.] Question Does anyone have a solution for this please? Thanks

    Read the article

  • How can I share a Windows 7 library with anonymous access without using a Homegroup?

    - by Triynko
    The "homegroup" feature is useless, because it requires a password, and therefore doesn't support anonymous, no-hassle access to shares from devices such as my Sony Bravia TV and non-Windows7 machines. So I turned off homegroup and reverted to the standard shared folders protocol. I'd like to share my Music "Library", so I can play files from my TV through the Surround Sound System, but there seems to be no option to share a library folder other than through a homegroup. I don't want to have to individually share the folders that belong to the library, because that would defeat the purposes of the library, which is to manage which folders are included in the library while also providing an easily accessible view of them all at once. Does anyone know how to share a Windows 7 library without that useless homegroup feature?

    Read the article

  • Why is the latency on one LVM volume consistently higher?

    - by David Schmitt
    I've got a server with LVM over RAID1. One of the volumes has a consistently higher IO latency (as measured by the diskstats_latency munin plugin) than the other volumes from the same group. As you can see, the dark orange /root volume has consistently high IO latency. Actually ten times the average latency of the physical devices. It also has the highest Min and Max values. My main concern are not the peaks, which occur under high load, but the constant load on (semi-)idle. The server is running Debian Squeeze with the VServer kernel and has four VServer containers and one KVM guest. I'm looking for ways to fix - or at least understand - this situation. Here're some parts of the system configuration: root@kvmhost2:~# df -h Filesystem Size Used Avail Use% Mounted on /dev/mapper/system--host-root 19G 3.8G 14G 22% / tmpfs 16G 0 16G 0% /lib/init/rw udev 16G 224K 16G 1% /dev tmpfs 16G 0 16G 0% /dev/shm /dev/md0 942M 37M 858M 5% /boot /dev/mapper/system--host-isos 28G 19G 8.1G 70% /srv/isos /dev/mapper/system--host-vs_a 30G 23G 6.0G 79% /var/lib/vservers/a /dev/mapper/system--host-vs_b 5.0G 594M 4.1G 13% /var/lib/vservers/b /dev/mapper/system--host-vs_c 5.0G 555M 4.2G 12% /var/lib/vservers/c /dev/loop0 4.4G 4.4G 0 100% /media/debian-6.0.0-amd64-DVD-1 /dev/loop1 4.4G 4.4G 0 100% /media/debian-6.0.0-i386-DVD-1 /dev/mapper/system--host-vs_d 74G 55G 16G 78% /var/lib/vservers/d root@kvmhost2:~# cat /proc/mounts rootfs / rootfs rw 0 0 none /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0 none /proc proc rw,nosuid,nodev,noexec,relatime 0 0 none /dev devtmpfs rw,relatime,size=16500836k,nr_inodes=4125209,mode=755 0 0 none /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000 0 0 /dev/mapper/system--host-root / ext3 rw,relatime,errors=remount-ro,data=ordered 0 0 tmpfs /lib/init/rw tmpfs rw,nosuid,relatime,mode=755 0 0 tmpfs /dev/shm tmpfs rw,nosuid,nodev,relatime 0 0 fusectl /sys/fs/fuse/connections fusectl rw,relatime 0 0 /dev/md0 /boot ext3 rw,sync,relatime,errors=continue,data=ordered 0 0 /dev/mapper/system--host-isos /srv/isos ext3 rw,relatime,errors=continue,data=ordered 0 0 /dev/mapper/system--host-vs_a /var/lib/vservers/a ext3 rw,relatime,errors=continue,data=ordered 0 0 /dev/mapper/system--host-vs_b /var/lib/vservers/b ext3 rw,relatime,errors=continue,data=ordered 0 0 /dev/mapper/system--host-vs_c /var/lib/vservers/c ext3 rw,relatime,errors=continue,data=ordered 0 0 /dev/loop0 /media/debian-6.0.0-amd64-DVD-1 iso9660 ro,relatime 0 0 /dev/loop1 /media/debian-6.0.0-i386-DVD-1 iso9660 ro,relatime 0 0 /dev/mapper/system--host-vs_d /var/lib/vservers/d ext3 rw,relatime,errors=continue,data=ordered 0 0 root@kvmhost2:~# cat /proc/mdstat Personalities : [raid1] md1 : active raid1 sda2[0] sdb2[1] 975779968 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdb1[1] 979840 blocks [2/2] [UU] unused devices: <none> root@kvmhost2:~# iostat -x Linux 2.6.32-5-vserver-amd64 (kvmhost2) 06/28/2012 _x86_64_ (8 CPU) avg-cpu: %user %nice %system %iowait %steal %idle 3.09 0.14 2.92 1.51 0.00 92.35 Device: rrqm/s wrqm/s r/s w/s rsec/s wsec/s avgrq-sz avgqu-sz await svctm %util sda 23.25 161.12 7.46 37.90 855.27 1596.62 54.05 0.13 2.80 1.76 8.00 sdb 22.82 161.36 7.36 37.66 850.29 1596.62 54.35 0.54 12.01 1.80 8.09 md0 0.00 0.00 0.00 0.00 0.14 0.02 38.44 0.00 0.00 0.00 0.00 md1 0.00 0.00 53.55 198.16 768.01 1585.25 9.35 0.00 0.00 0.00 0.00 dm-0 0.00 0.00 0.48 20.21 16.70 161.71 8.62 0.26 12.72 0.77 1.60 dm-1 0.00 0.00 3.62 10.03 28.94 80.21 8.00 0.19 13.68 1.59 2.17 dm-2 0.00 0.00 0.00 0.00 0.00 0.00 9.17 0.00 9.64 6.42 0.00 dm-3 0.00 0.00 6.73 0.41 53.87 3.28 8.00 0.02 3.44 0.12 0.09 dm-4 0.00 0.00 17.45 18.18 139.57 145.47 8.00 0.42 11.81 0.76 2.69 dm-5 0.00 0.00 2.50 46.38 120.50 371.07 10.06 0.69 14.20 0.46 2.26 dm-6 0.00 0.00 0.02 0.10 0.67 0.81 12.53 0.01 75.53 18.58 0.22 dm-7 0.00 0.00 0.00 0.00 0.00 0.00 7.99 0.00 11.24 9.45 0.00 dm-8 0.00 0.00 22.69 102.76 407.25 822.09 9.80 0.97 7.71 0.39 4.95 dm-9 0.00 0.00 0.06 0.08 0.50 0.62 8.00 0.07 481.23 11.72 0.16 root@kvmhost2:~# ls -l /dev/mapper/ total 0 crw------- 1 root root 10, 59 May 11 11:19 control lrwxrwxrwx 1 root root 7 Jun 5 15:08 system--host-kvm1 -> ../dm-4 lrwxrwxrwx 1 root root 7 Jun 5 15:08 system--host-kvm2 -> ../dm-3 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-isos -> ../dm-2 lrwxrwxrwx 1 root root 7 May 11 11:19 system--host-root -> ../dm-0 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-swap -> ../dm-9 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-vs_d -> ../dm-8 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-vs_b -> ../dm-6 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-vs_c -> ../dm-7 lrwxrwxrwx 1 root root 7 Jun 5 15:06 system--host-vs_a -> ../dm-5 lrwxrwxrwx 1 root root 7 Jun 5 15:08 system--host-kvm3 -> ../dm-1 root@kvmhost2:~#

    Read the article

  • NVRAM for journals on Linux?

    - by symcbean
    I've been thinking about ways of speeding up disk I/O, and one of the bottlenecks I keep coming back to is the journal. There's an obvious benefit to using an SSD for the journal - over and above just write caching unless of course I just disable the journal with the write cache (after all devicemapper doesn't seem to support barriers). In order to get the benefits from using a BB write cache on the controller, then I'd need to disable journalling - but then the OS should try to fsck the system after an outage. Of course if the OS knows what's in the batter-backed memory then it could use it as the journal - but that means it must be exposed as a block device and only be under the control of the operating system. However I've not been able to find a suitable low-cost device (no, write-levelling for Flash is not adequate for a journal, at least one which uses Smartmedia). While there's no end of flash devices, disk/array controllers with BB write caches, so far I've not found anything which just gives me non-volatile memory addressable as a block storage device.

    Read the article

  • Clever recording using AVFoundation

    - by martin
    Hello I am working on my master thesis and I am programming app for iOS using AVFoundation framework. I can make by myself session and attach devices to it and record video with sound. The main problem is that I need continous recording (3hours or longer). After three hours user will stop recording and user will choose time eg. 15 mins (max 30 mins) and only this last 15 mins will be stored to iphone memory. Is it possible to 'cut' video while recording or should I record it eg. in 10 minutes block and then delete old video segments and last two segments connect to one bigger? Will perform these connections (stop recording, start new recording and then connect these two segments) lags in final long video segment? Is there any way to perform this 'clever' recording? Thank you for any ideas.

    Read the article

  • How do I disable alert beeps

    - by wheresrhys
    My HP pavilion laptop is getting pretty old and the speakers no longer work properly. So I've disabled all audio devices, including disabling the light-touch volume controls at boot-up. The one sound still here that I can't get rid of is teh alert beep whenever there's an error. It's annoying at the best of times, but when your laptop has no other sounds at all it's intensly irritating! Nothing I change in the windows settings or in the BIOS seems to have any effect. Any ideas how to switch them off?

    Read the article

  • How do I disable aalert beeps

    - by wheresrhys
    My HP pavilion laptop is getting pretty old and the speakers no longer work properly. So I've disabled all audio devices, including disabling the light-touch volume controls at boot-up. The one sound still here that I can't get rid of is teh alert beep whenever there's an error. It's annoying at the best of times, but when your laptop has no other sounds at all it's intensly irritating! Nothing I chaneg in the windows settings or in the BIOS seems to have any effect. Any ideas how to switch them off?

    Read the article

  • Windows Server 2003 AD User Properties Environment doesn't override end user Remote Desktop Client s

    - by caleban
    Windows Server 2003 Domain Controller and Windows XP workstations: Active Directory Users and Computers/Users/User/Properties/Environment/Client devices Connect client drives at logon Connect client printers at logon Shouldn't the above Terminal Services settings in Active Directory override the end user Remote Desktop client settings? In our environment the end user Remote Desktop Client settings take precedence. If printing is disabled on the client but enabled in the user's AD profile then printing is not available. Is this working by design or can I change something to allow the user environment settings in AD to override the end user settings RDC settings?

    Read the article

  • dhcpd pool exhaustion - What's the result?

    - by jarmund
    I have a DHCP server that serves leases to several houndred, maybe up to a thousand, different clients on an average day. The pool consists of 242 IPs, and due to the highly dynamic nature of the network, it's enough 99% of the time (most devices are gone from the network in a few minutes), despite having a lease time of 3600. Now, imagine if more clients than that connect to the network during an hour. The sollution is obvious: Decrease lease time, or increase the DHCP pool, however, what i would like to know: What happens when dhcpd has exhausted the pool? Are new DHCP requests simply ignored?

    Read the article

  • Multicast in private LAN with different subnets

    - by Gobliins
    after i read Multicast IP Addresses and Multicast accross the subnets I am confused. Configuration: I have two devices in the same network. They may not be in the same Subnet, but always in the same physical network (beyond the same router, switch etc.) I want to communicate across IP multicast either 224.x.x.x or 239.x.x.x may be more fitting because we want it local, not beyond of forward through the router. Can one machine be the receiver and the other machine sender of the same multicast address? and can the receiving machine send an answer to the sending machine?

    Read the article

  • OpenWrt Backfire 10.03 Frequently Becoming Unresponsive (Bridged Client)

    - by Christopher Parker
    I have a Linksys WRT54G version 2 that I've flashed with OpenWrt Backfire 10.03. It's acting as a bridged client using the wl.o driver to give me network access in my home office, which is in a far corner of my house in a position that would make it exceedingly difficult to fish network cabling in through the walls. I have three network-ready devices attached to the device that don't currently support WiFi, including a networked printer. Ever since I migrated from WhiteRussian, which was also set up as a bridged client, to Backfire, the device has been becoming unresponsive, as though the OS itself has crashed or frozen. The WLAN light becomes completely solid and the LAN lights stay mostly solid, blipping off and then back on again maybe once a second or so. They all blink more or less in unison. Is there some way I can diagnose why this is happening so I can fix it? Right now, the only way to fix it is to unplug the device and plug it back in.

    Read the article

  • How to find the /dev name of my USB device

    - by mustafa
    I am running Ubuntu 11 on VmWare on Windows XP. I want to format an SD card in Ubuntu. But, I can't figure out which /dev/xxx device the SD card is. I plug the card into the built-in socket of my laptop. I "safely remove" the device in Windows. Then, I "connect" the PCMCIA reader in VmWare. Now, I was supposing to see a new device like /dev/sdx. But, it doesn't appear :( How can I find what the name of my USB device's name and mount it? /var/log/message is empty. Here is the output of dmesg: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd And, here is the last lines of /var/log/syslog: Oct 31 18:51:21 ubuntu kernel: [ 5268.927308] usb 2-1: new full speed USB device number 12 using uhci_hcd Oct 31 18:51:21 ubuntu mtp-probe: checking bus 2, device 12: "/sys/devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-1" Oct 31 18:51:21 ubuntu mtp-probe: bus: 2, device: 12 was not an MTP device

    Read the article

  • Using a MiFi via WDS

    - by Joril
    I have a Huawei R201 MiFi connected to the internet, and I'd like to use its internet connection even from devices that don't have WiFi, so I grabbed a wireless router I had lying around and configured WDS so that it'd connect to the MiFi, and this is working nicely (I can ping the MiFi from the router web interface). The next step was connecting my PC to the router via ethernet cable, but now I'm stuck... The PC can ping the router, but not the MiFi (they're all on the same subnet). Since the router can ping the MiFi, I guess this is some kind of routing issue? Should I get a more "flexible" router, such as one with DD-WRT maybe? Is what I'm trying to do even possible? (For the record the PC is running Lubuntu 11.10)

    Read the article

  • How to achieve reliable Gigabit Ethernet Link with my Acer Aspire Revo R3610?

    - by The Operator
    I want to stream HD movies over my wired Gigabit LAN from my PC to my Acer Aspire Revo R3610. It's connected with a 3ft Cat5e patch cable to my Netgear GS605v2 Switch. The PC acting as File Server is connected at 1Gbps to the Switch. Network driver options are set to defaults, including automatic speed/duplex negotiation on both machines. The Revo will not connect to my Network Switch at 1Gbps - the OS reports that it reverts to 100Mbps either shortly after connection or immediately upon connection. Through a process of elimination (trying different drivers, patch cables, ports on the switch, and other 1Gbps-capable devices connected to the Network switch which successfully achieve 1Gbps links and performance) I have drawn the conclusion there is either a Hardware or Software (Driver) issue with the Revo itself. I have performed tests using Windows 7 and Ubuntu 9.10. Can anyone offer insight on Gigabit Ethernet with the Revo?

    Read the article

  • Debian date jumping, causing complete lockup

    - by artfulrobot
    I have a Debian Squeeze VM that has suddenly chosen to jump it's date forwards just over a month, which seems to confuse it no end and cause it to require a hard reset (yikes!). There is nothing unusual in the logs, except that the datestamp suddenly jumps (today back to 2005). It's happened three times, so I don't think it's to do with the leap second issue as the last one of those was in July. When it happened once I spent ages checking stuff but could not find anything, decided to forget it. But three times is becoming an issue on a production server. Edits providing information requested in comments (thanks!): I do not have control over the hypervisor, it is a hired VM. # cat /sys/devices/system/clocksource/clocksource0/current_clocksource kvm-clock # ntpq -p remote refid st t when poll reach delay offset jitter ============================================================================== +grendel.exizten 130.149.17.8 2 u 29 64 77 14.811 1.778 1.744 *panoramix.linoc 193.67.79.202 2 u 32 64 77 19.729 -0.419 1.691 +robert.elnounch 213.251.128.249 2 u 27 64 77 17.762 0.600 1.722 -janetzki.eu 83.169.43.165 3 u 31 64 77 27.214 3.575 1.638

    Read the article

  • Streaming media from linux server - low footprint is crucial

    - by Mike Haye
    I recently pre-ordered the Raspberry Pi. http://www.raspberrypi.org/faqs For those of you who don't know it, it's a machine with 256 mb ram and a 700 MHz processor for $35. I plan to run linux on an SD card on this machine and have it act as both a htpc, VPN and media server. In regard to the media server part, I need to find some linux software that has a small footprint, but allows me to stream media to other devices connected to the internet (preferably without having to install any additional software on the client machines) Also, I would love if the video could be compressed, so the data usage wouldn't be so big for the client machine (e.g. when I'm using my data plan on my smartphone ;) ) Thanks in advance for any answers :) Mike.

    Read the article

  • How can I check whether a volume is mounted where it is supposed to be using Python?

    - by Ben Hymers
    I've got a backup script written in Python which creates the destination directory before copying the source directory to it. I've configured it to use /external-backup as the destination, which is where I mount an external hard drive. I just ran the script without the hard drive being turned on (or being mounted) and found that it was working as normal, albeit making a backup on the internal hard drive, which has nowhere near enough space to back itself up. My question is: how can I check whether the volume is mounted in the right place before writing to it? If I can detect that /external-backup isn't mounted, I can prevent writing to it. The bonus question is why was this allowed, when the OS knows that directory is supposed to live on another device, and what would happen to the data (on the internal hard drive) should I later mount that device (the external hard drive)? Clearly there can't be two copies on different devices at the same path! Thanks in advance!

    Read the article

  • Getting a black laptop screen

    - by Vivek
    I get a black screen when I boot my laptop. The laptop was in sleep mode initially, so when I pressed the power button, it looked as if it woke up from sleep mode, but the screen was blank. So, I held down the power button to force shutdown the laptop and then removed the battery. But after booting the laptop the screen still remains black. The bios/boot screen remains black as well. I have tried connecting it to external hdmi/vga/s-video devices and booting still no go. Windows loads fine, as I can type the password and get the 'Ding', then alt-f4 and shutdown windows. If it helps, the laptop model is Asus G1S-A1. Thanks in advance!

    Read the article

  • replacing 3 Cisco Catalyst 4500

    - by hoberion
    Our network supplier recommends replacing our 3 cisco catalyst 4500's because they are EOL and dont speak OSPF (which we really want) Its not my area of expertise so I cant say for sure if we really need to replace these units but for my company the estimated costs of 250K euro is a huge problem. Is there any way to cut down on costs (without moving from cisco devices), I heard the 4500´s can speak ospf but would need an upgrade of sorts? edit: version: IOS (tm) Catalyst 4000 L3 Switch Software (cat4000-I9K91S-M), Version 12.2(20)EW, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) supervisor: WS-X4013+ Cisco Catalyst 4500 Series Supervisor Engine II-Plus density: WS-X4306-GB Cisco Catalyst 4500 Gigabit Ethernet Module, 6 Ports (GBIC) WS-X4306-GB Cisco Catalyst 4500 Gigabit Ethernet Module, 6 Ports (GBIC) WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45) WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45) WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45)

    Read the article

  • Questions about linux root file system.

    - by smwikipedia
    I read the manual page of the "mount" command, at it reads as below: All files accessible in a Unix system are arranged in one big tree, the file hierarchy, rooted at /. These files can be spread out over several devices. The mount command serves to attach the file system found on some device to the big file tree. My questions are: Where is this "big tree" located? Suppose I have 2 disks, if I mount them onto some point in the "big tree", does linux place some "special marks" in the mount point to indicate that these 2 "mount directories" are indeed seperate disks?

    Read the article

< Previous Page | 117 118 119 120 121 122 123 124 125 126 127 128  | Next Page >