Search Results

Search found 5367 results on 215 pages for 'devices'.

Page 118/215 | < Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >

  • Meinberg ntp for Windows - force more frequent updates?

    - by ana
    I have a Windows VM that has time drift problems, and left to its own devices will drift by minutes per day. I know there are issues with time on VMs, but I was hoping using the Meinberg NTP service would be successful. It works, generally, in that the time gets corrected in one big step about once every 70mins when it's at about 10mins offset. This has totally confused me as I thought NTP was meant to drift gently back towards the right time, and panic and die if the offset was more than 3 minutes. So (a) what is happening and (b) how do I make it update more regularly?

    Read the article

  • What decent audio recording interfaces are well supported in Windows 7 64bit?

    - by labradort
    I currently have an Audigy 2 ZS Platinum. It permits me to insert a 1/4" jack line from bass guitar and play along with pre-recorded piano music. This worked fine under Windows XP. I am moving to Windows 7 64 bit (dual boot for now), and Creative may not develop fully working drivers for this component. Looking around, I don't see Windows 7 support mentioned at product web sites from E-MU, Roland, M-Audio, etc. Even at Creative, the posting of available drivers for Windows 7 is deceptive, as they do not adequately support recording (latency, distortion). My local music store shrugs and says to stay with Win XP. In some cases, the Vista drivers will work in Win 7. So I need real world feedback on this. I should also mention I'm not impressed with available USB interfaces - they have too low of a signal to noise ratio for my purposes. That leaves PCI, or possibly firewire devices (never tried one yet).

    Read the article

  • Single-port 2600 router with 2900XL switch

    - by Slava Maslennikov
    I have a setup, where the single port 2600 router is in port 0/2 in the switch, outside network is on port 0/1, and the rest (0/3-0/24) should be clients for the second network that would be managed by the 2600 router. I configured everything with two VLANs: 100 for outside (0/2-0/24), 200 for inside (0/1-0/2). 0/2 is a trunk port for the two VLANs. The issue that came about is that I can't have two VLANs on at once: software doesn't allow it. Now, I can ping the outside network devices (172.16.7.1, 172.16.7.103), and even google (8.8.8.8) from the router, but not the switch. Devices on connected get a DHCP lease properly but can't ping outside the network, just the router - 172.17.7.1 and the switch itself, 172.17.7.7. The configuration for both the router and the switch are here, as well as below. Router: rt.throom#sho run Building configuration... Current configuration : 1015 bytes ! version 12.1 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname rt.throom ! enable password To053cret ! ! ! ! ! no ip subnet-zero ip dhcp excluded-address 172.17.7.1 172.17.7.2 ip dhcp excluded-address 172.17.7.3 172.17.7.4 ip dhcp excluded-address 172.17.7.5 ! ip dhcp pool VLAN200 network 172.17.7.0 255.255.255.0 default-router 172.17.7.1 dns-server 8.8.8.8 ! ip audit notify log ip audit po max-events 100 ! ! ! ! ! ! ! interface Ethernet0/0 no ip address ! interface Ethernet0/0.100 encapsulation dot1Q 100 ip address 172.16.7.15 255.255.255.0 ip nat outside ! interface Ethernet0/0.200 encapsulation dot1Q 200 ip address 172.17.7.1 255.255.255.0 ip nat inside ! router eigrp 20 network 172.16.0.0 network 172.17.0.0 no auto-summary no eigrp log-neighbor-changes ! no ip classless no ip http server ! access-list 1 permit 172.17.7.0 0.0.0.255 ! ! line con 0 line aux 0 line vty 0 4 login ! end Switch: sw.throom#sho run Building configuration... Current configuration: ! version 11.2 no service pad no service udp-small-servers no service tcp-small-servers ! hostname sw.throom ! enable password Oh5053cret ! ! no spanning-tree vlan 100 no spanning-tree vlan 200 ip subnet-zero ! ! interface VLAN1 no ip address no ip route-cache ! interface FastEthernet0/1 switchport access vlan 100 spanning-tree portfast ! interface FastEthernet0/2 switchport trunk encapsulation dot1q switchport mode trunk ! interface FastEthernet0/3 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/4 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/5 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/6 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/7 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/8 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/9 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/10 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/11 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/12 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/13 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/14 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/15 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/16 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/17 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/18 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/19 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/20 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/21 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/22 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/23 switchport access vlan 200 spanning-tree portfast ! interface FastEthernet0/24 switchport access vlan 200 spanning-tree portfast ! ! line con 0 stopbits 1 line vty 0 4 login line vty 5 9 login ! end sho ip route gives: Gateway of last resort is 172.16.7.1 to network 0.0.0.0 172.17.0.0/24 is subnetted, 1 subnets C 172.17.7.0 is directly connected, Ethernet0/0.200 172.16.0.0/24 is subnetted, 1 subnets C 172.16.7.0 is directly connected, Ethernet0/0.100 S* 0.0.0.0/0 [1/0] via 172.16.7.1

    Read the article

  • Slight network lag on Small Business Server 2008 R2

    - by Sir.Nathan Stassen
    I recently upgraded a network from a SBS 2003 server to a SBS 2008 R2 Server. Both I and users have noticed a slight delay in network applications and browsing network drives on the new server. It is minor, maybe a second or two at most. However I am wondering if anyone knows of anyway to optimize the networking to service requests sooner to the workstations. The network is running a 1 gig network with some 100 meg devices (mainly network printers). All workstations are XP SP3 Network software runs out of a shared folder mapped as a network drive, no sql databases. Server is a Dell Poweredge T610 with plenty of ram, cpu power, and storage.

    Read the article

  • Need assistance setting up Linux Router with 2 public lans

    - by user195407
    I was assigned a.b.c.10/30 (Public IP) for my router and given a.b.c.9 as the gateway. I was also assigned x.y.z.128/25 (Public IP block) for my use. I want to setup a Linux router to handle this situation. My Linux box has 3 NICs, eth0 is a.b.c.10, eth1 I have assigned x.y.z.254, eth2 is unused at present. I have eth1 connected to a network switch, and several devices connected. Let's say box A is x.y.z.129 with a gateway of x.y.z.254. I have not connected to the network yet, as it is not live. What settings do I need to make, beyond adding the 2 network definitions to the cards and having "route add default gw a.b.c.9 eth0"? I may add a private 192.168.100.0/24 lan to eth2 later.

    Read the article

  • Wi-Fi connected but can't go to any site

    - by Michael Dy
    My Windows 7 laptop can connect to our Wi-Fi signal, I can sign in on Yahoo! Messenger, but I can't go to any site. I can access the Net on other devices. The issue started a few weeks ago, so I've been troubleshooting since then in vain. There's no virus, and I already used System Restore. In Wireless Network Connection Status, the received activity is greater than the sent activity. I turned off Windows Firewall and still no Net access. My ping tests: How do I fix this?

    Read the article

  • How to diagnose repeated freezing of windows 7 (comes back alive in few seconds)

    - by Akash Kava
    I installed Windows 7 in a 3 year old machine, it installed successfully, took all drivers and running great, but what happens is every 5-6 minutes it freezes for few seconds... 30 seconds to 1 minute and then comes back alive. I checked Event Viewer, nothing matching the frozen timeline. I would appriciate any help on how to detect causing service/hardware. After it comes alive, everything runs normal, I did run task manager and checked cpu usage, at time it freezes just before and after that no task took more cpu or memory, it was like idle machine. No external usb drives or no devices, on board intel desktop board with SATA HDD, SATA hdd running in absolute good mode.

    Read the article

  • Hardware asset management systems

    - by Dave
    I need to track a bunch of specialized testing tools, They are hardware devices used for testing other equipement. Each device has a serial number and is sent out for use in testing. Occasionally they break and have to be sent to the manufacture for repair. I'm looking for an open source application (preferably a webapp) to help manage them. Right now we're using Excel and it's not scaling as we get more tools. They aren't computers so all the standard IT asset management systems don't really fit the bill. I found h-harmony, but that project seems dead?

    Read the article

  • Corrupted .WAR file after transfer from 32-64 bit Windows Server to Desktop or vice versa

    - by Albert Widjaja
    Hi All, Does anyone experience this problem of corrupted .WAR file after it has been copied over the network share ? this is .WAR file (Web Archive) the J2EE application file (.WAR file is compressed with the same zip algorithm i think ?) Scenario 1: Windows Server 2008 x64 transfer into Windows XP using RDP client (Local Devices and Resources) Scenario 2: Windows XP 32 bit transfer into Windows Server 2003 x64 using shared network drive (port 445 SMB ?) for both of the scenario it always failed / corrupted (the source code seems to be duplicated at the end of line when you open up in the Eclipse / Java IDE). but when in both scenario i compressed the file into .ZIP file everything is OK. can anyone explains why this problem happens ? Thanks, Albert

    Read the article

  • How does bridged networking work?

    - by agz
    How does bridged networking work? I have looked through the virtualbox manuals but nothing extremely technical came up (It was just a generic gloss over of the topic) How does it assign a different ip to the virtual machine but uses the same network card? Why does this different ip (I found using ip addr under linux) not show up under the "attached devices section" of my router but I can port forward to it? How come if I connect to a password protected wifi network, it does not require me to enter my password? Is this multihoming?

    Read the article

  • VoIP - need setup ip network with our SIP operator

    - by evgeniy.labusnkiy
    Need to make next one: for ex i'm now in UAE, but i need to make a call to my girlfriend who is in Ukraine. I need to find the way how can i make the connection to my home router and make the call from VoIP gateway using my standard phone network in Ukraine. I have some imagination about this, to do like this: Connect to router or VoIP gateway (how? soft?) using inet - Gateway make a call using standard phone line in my country. Any ideas? Best practice? What devices i need to make this? Pay attention that i don't want to use any SIP providers. Thats a lot!

    Read the article

  • What are the best options for a root filesystem hosted on SSD under Linux

    - by stsquad
    I'm working on an embedded system which is going to be booting and hosting it's rootfs on an SSD disk. We are currently looking at using Intel X-18M SSDs. The file system structure will have a fairly static /usr section (modulo software upgrades) and an active /var and /var/log for maintaining state and logging. Given the wear-levelling done by the underlying flash does having separate partitions help or hinder? As modern SSDs appear as straight block devices and hide their mapping magic behind their firmware is there any point trying to optimise the choice of file-system that sits on-top of the SSD? Finally does enable SMART monitoring make any sense in this context or are their SSD specific ways of determining the underlying health of the storage hardware?

    Read the article

  • How to get started with tcp/ip v6?

    - by Johan
    Hi Now and then there is "news" about that the ip numbers will run out in X years, and we must change to tcp/ip v6... And even thou this crisis never really happens it has waken a question, how do you get started with tcp/ip v6? What can I do at home and is this a good or bad idea? Can you use IPv4 and IPv6 in the same cables in the same LAN, or do you need to physically separate them? Can you have some translation box so you can reach the "normal" internet from the IPv6 connected devices? (Just like a NAT-Router) Can someone please clarify the situation a little bit? Thanks Johan

    Read the article

  • The meaning of thermal throttle counters and package power limit notifications in Linux

    - by Trustin Lee
    Whenever I do some performance testing on my Linux-installed MacBook Pro, I often see the following messages in dmesg: Aug 8 09:29:31 infinity kernel: [79791.789404] CPU1: Package power limit notification (total events = 40365) Aug 8 09:29:31 infinity kernel: [79791.789408] CPU3: Package power limit notification (total events = 40367) Aug 8 09:29:31 infinity kernel: [79791.789411] CPU2: Package power limit notification (total events = 40453) Aug 8 09:29:31 infinity kernel: [79791.789414] CPU0: Package power limit notification (total events = 40453) I also see the throttle counters in the sysfs increases over time: trustin@infinity:/sys/devices/system/cpu/cpu0/thermal_throttle $ ls core_power_limit_count package_power_limit_count core_throttle_count package_throttle_count $ cat core_power_limit_count 0 $ cat core_throttle_count 41912 $ cat package_power_limit_count 67945 $ cat package_throttle_count 67565 What do these counters mean? Do they affect the performance of CPU or system? Do they result in increased deviation of performance numbers? (i.e. Do they prevent me from getting reliable performance numbers?) If so, how do I avoid these messages and increasing counters? Would running the performance tests on a well-cooled desktop system help?

    Read the article

  • Windows 7 Professional doesn't mount my usb flash drive anymore

    - by Valter Henrique
    I have a Kingston flash drive which works fine in every computer that I insert it. But in my Windows 7 it doesn't mount anymore. Why this is happening ? When I insert the flash drive it seems that the Windows 7 recognize it, but when I hover the icon don't show the flash drive to remove it, as usually does. Any idea ? Thanks. Any idea ? Abrir Dispositivos e Impressoras, means, ' Open devices and printers' .

    Read the article

  • KVM Guest installed from console. But how to get to the guest's console?

    - by badbishop
    I'm trying to install a fully virtualized guest (Fedora 14 x86_64) on KVM (RHEL 6), using command-line only (both hypervisor and guest). It goes without errors, and without a tangible result . I'd like to know how to do a text-only installation. So, here's what I've done: # virt-install \ --name=FE --ram=756 --vcpus=1 \ --file=/var/lib/libvirt/images/FE.img --network bridge:br0 \ --nographics --os-type=linux \ --extra-args='console=tty0' -v \ --cdrom=/media/usb/Fedora-14-x86_64-Live-Desktop.iso Starting install... Creating domain... | 0 B 00:00 Connected to domain FE Escape character is ^] ÿ Now what? As I understand after googling for a couple of days, I should see the guest's output from the text installation, but nothing happens. virt-viewer cannot connect to it, kindly suggesting that I explore all the options by adding --help (which I did). If I reconnect with virsh, I see this: Domain installation still in progress. You can reconnect to the console to complete the installation process. [root@v ~] # virsh console FEConnected to domain FE Escape character is ^] This shows that VM is running # virsh list Id Name State ---------------------------------- 8 FE running Qemu log: LC_ALL=C PATH=/sbin:/usr/sbin:/bin:/usr/bin /usr/libexec/qemu-kvm -S -M rhel6.0.0 -enable-kvm -m 756 -smp 1,sockets=1,cores=1,threads=1 -name FE -uuid 6989d008-7c89-424c-d2d3-f41235c57a18 -nographic -nodefconfig -nodefaults -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/FE.monitor,server,nowait -mon chardev=monitor,mode=control -rtc base=utc -no-reboot -boot d -drive file=/var/lib/libvirt/images/FE.img,if=none,id=drive-ide0-0-0,format=raw,cache=none -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive file=/media/usb/Fedora-14-x86_64-Live-Desktop.iso,if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -netdev tap,fd=20,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=52:54:00:0a:65:8d,bus=pci.0,addr=0x2 -chardev pty,id=serial0 -device isa-serial,chardev=serial0 -usb -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x3 char device redirected to /dev/pts/1 Output of /etc/libvirt/qemu/FE.xml # cat /etc/libvirt/qemu/FE.xml <domain type='kvm'> <name>FE</name> <uuid>6989d008-7c89-424c-d2d3-f41235c57a18</uuid> <memory>774144</memory> <currentMemory>774144</currentMemory> <vcpu>1</vcpu> <os> <type arch='x86_64' machine='rhel6.0.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='none'/> <source file='/var/lib/libvirt/images/FE.img'/> <target dev='hda' bus='ide'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:0a:65:8d'/> <source bridge='br0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target port='0'/> </console> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </memballoon> </devices> </domain> I'm obviously missing something that many others don't, but what is it? Thanx in advance!

    Read the article

  • wireless access point

    - by Warren Bullock III
    I'm hoping to get some suggestions for possible Wireless Access point/router models which will allow us to have two separate networks. We run an internal network on 10.x.x.x IP range where we have shares and other network resources for which we would like to have our regular users access. However, we would also like to offer a separate wireless network for guests which ideally would be on 192.168.x.x and these users would not be able to see any of the resources sitting on the 10.x.x.x network. Anyone have any recommendations on single devices that might be able to get the job done? I was looking at the Linksys E4200 and it seems to support what I'm looking to do... any others? Thanks in advance for any suggestions.

    Read the article

  • Cannot find the "Create Network" menuitem in the WiFi icon menu in Mountain Lion

    - by Chuancong
    I am using Mountain Lion Developer Preview 2. I cannot find the "Create Network" menuitem in the WiFi icon menu in the menubar. It was there before when I was using Lion. It started missing since I upgraded to Mountain Lion Developer Preview 1. By the way, is there any other method to create an ad-hoc WiFi network on OS X? I tried to use Internet Sharing via WiFi, but other devices using the shared connection could not find the Mac in their local networks. I am using an early 2011 MacBook Pro 15'. Thanks.

    Read the article

  • How can I tell if I have PCI Express 2.0 or 2.1?

    - by Stefan Lasiewski
    I am looking at a variety of PCI Express cards, such as a SATA RAID Controller and a Video Card. Some of these cards say they only support PCI Express 2.1, not PCI Express 2.0. I know that my motherboard supports PCI Express 2-something, but the manual doesn't say '2.0' or '2.1'. How can I tell if the PCIe slot on my motherboard is PCI Express 2.0 or PCI Express 2.1? Is it possible to determine the PCIe type from the Windows or Linux commandline? I was under the impression that most PCI Express 2.1 devices are backwards compatible with PCI Express 2.0. Is it possible that the vendor is wrong in saying that PCI Express 2.1 is required?

    Read the article

  • Ubuntu Nvidia Xorg Twinview doesnt like my monitors

    - by Andrew Bolster
    Basically, using the latest available ubuntu drivers (195.36.15) I cannot for the life of me get my two monitors to operate at suitable resolutions. When not using the drivers atall and going single-screen, both monitors support 1680x1050, but this option is only shown for one monitor in nvidia-settings, and when i manually add a metamode into the xorg.conf, it just gives up initialising the second screen. (**) Mar 25 15:49:47 NVIDIA(0): TwinView enabled (II) Mar 25 15:49:47 NVIDIA(0): Assigned Display Devices: CRT-0, CRT-1 (II) Mar 25 15:49:47 NVIDIA(0): Validated modes: (II) Mar 25 15:49:47 NVIDIA(0): "1680x1050,1680x1050" (II) Mar 25 15:49:47 NVIDIA(0): Virtual screen size determined to be 1680 x 1050 Any ideas?

    Read the article

  • Ubuntu Nvidia Xorg Twinview doesnt like my monitors

    - by Andrew Bolster
    Basically, using the latest available ubuntu drivers (195.36.15) I cannot for the life of me get my two monitors to operate at suitable resolutions. When not using the drivers atall and going single-screen, both monitors support 1680x1050, but this option is only shown for one monitor in nvidia-settings, and when i manually add a metamode into the xorg.conf, it just gives up initialising the second screen. (**) Mar 25 15:49:47 NVIDIA(0): TwinView enabled (II) Mar 25 15:49:47 NVIDIA(0): Assigned Display Devices: CRT-0, CRT-1 (II) Mar 25 15:49:47 NVIDIA(0): Validated modes: (II) Mar 25 15:49:47 NVIDIA(0): "1680x1050,1680x1050" (II) Mar 25 15:49:47 NVIDIA(0): Virtual screen size determined to be 1680 x 1050 Any ideas?

    Read the article

  • Instant messanger capable of offline messaging & tolerant of network interruptions

    - by Terry
    I am looking for an instant messaging solution to facilitate communications between recovery vehicles in remote rural areas. All the vehicles have internet connections, but they are intermittent depending on location. Ideally we'd like something that has the following features: Offline messaging: messages sent to clients who are offline will be delivered when they next come online, regardless of whether the sender is still online or not. Lightweight: CPU cycles are limited on the machines in these vehicles. A bloated solution will be an issue. Client platform is primarily win32, but support for osx/linux/mobile devices would be a bonus. Non-chatty: Bandwidth is a precious commodity for us, so services which use a minimal amount are ideal. Fault tolerant: We see plenty of packetloss and high latency, so whatever we use needs to be able to function in trying network conditions. I'm not fussed if we use a hosted platform like gtalk/skype/msn/icq/whatever, and likewise I can run a server if need be. Suggestions would be appreciated!

    Read the article

  • How to capture footage from an analog TV?

    - by hope
    I have only an old analog TV with just RCA connectors and a coaxial/cable in/out wire. It uses no HDMI interface, etc. I would like to know the cheapest method possible where the current video footage can be transferred and made into a target digital video file format and be copyable/transferrable via USB. Are there any devices that can do this with an analog TV? Basically, how can I get something along these lines done and for cheap?P I do NOT want to stream; I want footage recorded off the TV and stored via a digital encoding of a video file.

    Read the article

  • Separating two networks

    - by Farhan Ali
    I have two routers, R1 and R2. R1 (a stock linksys router running dd-wrt) is connected to internet and is serving internet to a network of 5 devices/PCs running a DHCP server, with a network of 192.168.1.0/24. R1 also serves internet services to R2. R2 (a ubuntu server 12.04) gets internet from R1. R2 has 3 PCs attached to it, runs a DHCP server with a network of 172.22.22.0/24. My requirement is that the clients on both sides should not talk to each other at all – with the exception that R1 clients may access the R2 router through its IP of 192.168.1.x. At the moment, R2 clients are able to ping R1 clients, which is unacceptable, whereas R1 clients cannot ping R2 clients, which is OK. I believe iptables could be set up but I don't know how.

    Read the article

  • external SCSI tape drive DAT 72 problem Solaris 10

    - by Hassan
    Hi all, I have solaris 10 sparc running and working very well but i have problem with external SCSI tape drive DAT 72 problem it seems to me the tape drive is manufactured by SUN microsystems when i ran mt -f /dev/rmt/0 status it reveals the following output bash-3.00# mt -f /dev/rmt/0 status /dev/rmt/0: No such file or directory when i ran ls -l it reveals the following output ls -l /dev/rmt/0 lrwxrwxrwx 1 root root 43 Sep 20 2006 /dev/rmt/0 -> ../../devices/pci@8,600000/scsi@1,1/st@3,0: it seems to me everything is okay SCSI cable is connected properly to Tape device and to server as well the tape has SCSI termination dongle as well and connected properly to Tape device as well any ideas would be a great assist Thanks in advance

    Read the article

< Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >