Search Results

Search found 2066 results on 83 pages for 'cable'.

Page 16/83 | < Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >

• Intermittent USB 3.0 access - How do I troubleshoot?

  - by Billy ONeal

  I've got a WD Passport hard disk with "superspeed" USB 3.0 support. When I use my USB 3.0 flash drive (this is a Lenovo X220 laptop), USB 3.0 consistently works. But when I use the passport drive, almost without fail the connection drops to USB 2.0. Touching the cable seems to immediately trigger the problem, but it seems to happen on its own though. I've got another cable on order right now... but is it likely the cable's the issue here? Is there anything else I can check?

  Read the article

• Bridging two connections in windows 7

  - by Serban Razvan

  I have recently bought an Samsung UE32ES5500 and I want to connect it to the internet. Not wanting to buy an expensive Samsung wireless adapter for the TV, I've decided to use an ethernet cable. Because the Internet cable passes through underground to the bedroom and the TV is located in the living room, i decided to put a router in the bedroom, and receive it's signal in the living room using a windows 7 laptop. Afterwards I connected the laptop to the TV through an ethernet cable, and bridged the two connections in Network Connections in Control Panel on the laptop. The TV successfully finds the laptop (and the router I think) but still cannot connect to the internet. Does anyone knows a solution to this problem? (the connections must be bridged because I want to have only one network in the house)

  Read the article

• How to fix unstable RJ45 jacks? [closed]

  - by BeemerGuy

  This is a little project I'm doing at home. I wanted to wire two rooms together (basically, the router is one room, and the switch is in the second room). So I ran a CAT5 between the two rooms, and wired an RJ45 jack in each room. I then hooked up the two jacks with two CAT5 cable to run it through the cable tester, and all 8 wires seem good. Now, when I connect the switch and the router, the connection is unstable -- I ping the router and it barely holds on for two pings before it disconnects, and stays in that unstable state. Just to make sure the router and the switch are ok, I connected them with long wire between the two rooms and the connection is absolutely stable, and pings continuously. What could be the cause for the unstable connection? Especially that it pings a few times, so there IS a connection. But why is it unstable? And how come the cable tester says it's ok, but it's unstable?

  Read the article

• Ubuntu 9.10 freezes when HDMI port is connected

  - by Felipe Hummel

  Hi, I have a Sony Vaio FW350 with a HDMI output. I'm trying to use it under Ubuntu 9.10 with a LG LCD monitor 21,5'. I've tried two approaches: Boot the laptop with the HDMI cable connected and monitor turned on. Result: LCD Monitor keeps turned on but the whole screen is black and Ubuntu do not seem to be initializing. Boot Ubuntu until the end. I then connect the HDMI cable into the Laptop. The mouse and the whole system freezes. In both cases the only way to turn off the laptop is holding the power button. I've looked around the internet for similar problems, but only found workarounds for the same problem with VGA input, not HDMI. I also tried to use metacity before connecting the cable, but still got the same result. Any hints?

  Read the article

• Upgrading HP DL185 G5 8LFF, is using a Dell J1520 4-Drop SATA Adapter possible?

  - by jpreed00

  The HP DL185 G5 8LFF model supports 8 3.5" drives and 1 optical drive. However, instead of the optical drive, I'd like to have 2x 2.5" drives instead. The problem is that the PSU has no more SATA power cables (even though the motherboard has 4 additional SATA data ports). The PSU does have a free 10-pin connector and it looks like the J1520 cable from Dell would fit the bill. Link to cable description Does anyone have any experience using these cables? Are they safe? Any other ideas for adding the disks to the server if I don't use the cable? Thanks!

  Read the article

• Network router and switch configuration

  - by gilly3

  Can I put a switch before my router in my home network? Here is a diagram of how I want to set up my network: ________________________________ ________________________________________ | | | | | Cable Access Panel | | Home Office | | _____________ ________ | | _____________ | | | | | | | | | | _________ | | | Cable Modem |--->| Switch |-------------->| Router |____| | | | |_____________| |________| | | |_____________| | Printer | | |______________________/____\____| | / | \ |_________| | ___/_ _\___ | _____/ ____|____ \_____ | | | | | | | | | | | | | | PC1 | | PC2 | | | PC3 | | Ext. HD | | PC4 | | |_____| |_____| | |_____| |_________| |_____| | |________________________________________| The reason I want to do this is because my router is also my wireless access point. My cable modem is located in the far corner of my home where my phone/tv/network access panel is. I'd rather keep the wireless access point in a more central location, but I'm not sure if DHCP will continue to work properly with that configuration. Edit: I'd like to continue to be able to share files and access my networked drive and printer from each computer in the house.

  Read the article

• How to setup a wired local area network in Windows 7?

  - by user883434

  I am using a Lenovo ThinkPad X200 and want to se tup a wired local area network. How could I achieve this? Actually, my question is very simple. I just want to connect to the internet and I have a cable connection at home. So, I just want to plug the cable line to my notebook (x200) so that I can access the internet via the cable. But I dont know how to setup a local area connection in notebook. Since it automatically appear in my desktop, but not in my notebook. Thanks!

  Read the article

• Ubuntu 9.10 freezes when HDMI port is connected

  - by Felipe Hummel

  I have a Sony Vaio FW350 with a HDMI output. I'm trying to use it under Ubuntu 9.10 with a LG LCD monitor 21,5'. The laptop has a Intel 4500 video card. I've tried two approaches: Boot the laptop with the HDMI cable connected and monitor turned on. Result: LCD Monitor keeps turned on but the whole screen is black and Ubuntu do not seem to be initializing. Boot Ubuntu until the end. I then connect the HDMI cable into the Laptop. The mouse and the whole system freezes. In both cases the only way to turn off the laptop is holding the power button. I've looked around the internet for similar problems, but only found workarounds for the same problem with VGA input, not HDMI. I also tried to use metacity before connecting the cable, but still got the same result. Any hints?

  Read the article

• Network configuration with limited hardware

  - by Pavel

  I have cable internet and I have two PC. One of them has wireless and ethernet, the other pc has ethernet only. Also, I have a dsl modem that has wireless builtin (some common speedstream model). My goal is to connect all of them so that both have internet access. As I understand, I have two options: connect speedstream to the cable and then connect other PC's to speedstream; OR, connect pc with wireless to the cable and then connect the other pc that has ethernet only using ethernet+wireless through speestream. First one seems to be easy, but it doesn't seem to work. What about the other choice? Is it possible to do it?

  Read the article

• make a computer recognized as a usb flash drive?

  - by user137560

  Is there anyway to make a folder or a partition on a computer (Linux/windows) to act like a flash drive to other computers or devices when connected with a usb cable. For example, I have a windows 7 computer with 2 partitions c and d, then connect that computer to another computer or a smart TV using a USB cable (has to be male to male USB cable) then the other computer or TV recognizes the current computer as a usb device. Is that possible, if not is there any usb switch to connect an external hard drive or flash drive to both the computer and TV without the need to manually switch them (I know about some USB switches but they only support automatic switching with some certain types of printers, not with mass storage) Thanks in advanced! Sam

  Read the article

• Does Asus F8SV supports 1920*1080 resolution through DVI output? [closed]

  - by Col

  Devices: Asus F8Sv Laptop (Windows 7 ultimate, GeForce 8600m GT, display driver is 301.42, detected and downloaded from nvidia.com, VGA and DVI output interface) Gateway 23 inches LCD monitor (VGA, DVI-D with HDCP, and HDMI input) 18 pins DVI cable, VGA cable, both new. Problems: When connect laptop to monitor by VGA, resolution is automatically adapted to 1920*1080; but when using DVI connection, resolution on monitor is fixed to 1024*768, which is lower than my laptop default 1280*800. The maximum resolution in windows control panel is only 1024*768, while the Nvidia control panel provides options 1920*1080p and 1920*1080i, but clicking apply button does not work, the resolution just can not change. Possibly reason I guess: GeForce 8600m GT does not support 1920*1080 resolution through DVI outputs. Can anyone confirm it or give the real reason? edit: Problem solved by buying a HDMI to DVI-D adapter. Using this adapter and a HDMI cable, I can now enjoy 1080p movie.

  Read the article

• My monitor constantly changes from DVI-D to HD15

  - by guest

  I noticed this lately, and it's becoming more often. Basically, when I start my PC, my monitor, which is connected with a DVI-D cable (I don't know what it's called), screen switches to the HD15, where HD15 isn't connected at all. Like, input is changed from DVI-D to HD15, therefore it just blacks out, and then goes back... it's not constant, but it's in random time intervals... I can't do anything on my computer because of this. I even tried connecting it with both DVI-D cable and HD15 cable to the processor, but it still sucks. Is there any way I could force my monitor to stay at only one input method? I'm on XP SP3, and this monitor is about 10 or less years old, a Sony model.

  Read the article

• Problem with Mono and .exe file

  - by Vere Nicolson

  I have purchased a piece of software to configure programable radio control transmitters. It says it will run on Linux, see below: Digital Radio runs on: Microsoft Windows 2000/2003/XP Microsoft Windows Vista/Seven/2008, Linux Ubuntu or a distribution with Mono, 32 or 64 bit, also in a virtual machine. Linux requires the Mono package installed, with also the Visual Basic 2005 runtime library. The Linux version is the same executable file of the Windows platform, and can be execute using Mono. You don't need Wine. All the tests have been done on Ubuntu Desktop 10.10 I have tried for weeks to get the drivers for the cable to work in XP or Win7 and I admit defeat. It looks like Ubuntu can run the cable effortlessly but now I can't get the software going. Tried to run in Ubuntu 10.04 with mono, GUI failed and I got the following message in terminal. $ mono ~/Desktop/GigRadioLinux/DigitalRadio/DigitalRadio.exe The entry point method could not be loaded Windows installation requires using a 30 odd character Passkey and a 4.24k text file as a "license" to be entered during running of the exe file. Can someone tell me how I enter the passkey and license into terminal, or is that not my primary problem? I don't understand "entry point method". Tried Wine and that didn't work either. The developer responded to my earlier emails re the cable drivers, but hasn't replied to questions regarding this. If I have left out anything important let me know and I will try to supply more information.

  Read the article

• crash when using wireless network

  - by Erik

  ubuntu 12.04 32 bit When I start up my system almost instantly freezes, I found that the problem lays with my wireless network, because the crash is always t the same time as the message that tells me I am connected to a network when I start up connected to a cable everything works fine, I can even see that I am connected to our wireless network, until I unplug the ethernet cable, then it all freezes again the same happened when I boot from a live cd (from usb) The problem only occurs on my netbook, my laptop doesn't give any problems. I don't know if anyone else has had similar problems, or if anyone knows a solution... Thanks in advance! greetings Erik EDIT (21/3/2012): it seems there is some external factor involved, I'm using my netbook for about 50 minutes now while connected to the wireless network, and still it didn't crash strange enough, before these 50 minutes I had to put it down by holding the power button, because I decided to try it again, that time it did crash... before (while connected with an ethernet cable) I've been trying to get my Bluetooth working, that didn't succeed entirely, but I guess that might be a factor in the question why it doesn't crash at the moment now I rebooted, connected, and no crash... if it crashes again, I'll update this post again. in the meantime, if anyone has an idea on what could be a factor, and on how to create a crash using that factor, feel free to ask!

  Read the article

• Black screen on login, can get thru decrypt disk and access command line but no GUI

  - by t3lf3c

  Running 12.04 64 bit fresh alternative install, with disk crypto on a new Lenovo laptop Install didn't connect and install modules, even though I had the network cable plugged in and don't have any whacky proxy settings. I had to manually install ubunut-desktop and define sources after initial installation, so this seemed a bit weird (ISO matched MD5 sum though) I unplug the network cable, otherwise I get a black screen that I can do nothing with. So I turn laptop on, I have disk encryption, I type in the password at the Ubuntu decryption GUI then get "set up successfully" message "Waiting for network configuration ..." then "Waiting for up to 60 more seconds for network configuration" At this stage (a) If I wait for it then I get a black screen that I can do nothing with. (b) If I interrupt the process by pressing escape, then I break through to the command line. From the command line, I can go ahead and login, then plug my network cable in to do apt-get commands. As a precaution I do some house keeping which takes a few mins to run: sudo apt-get update sudo apt-get upgrade Running startx to get to the GUI gives: Fatal server errror: no screens found The .Xauthority file is being created in my home directory but it's empty. I review my order and note the system graphics: Intel HD Graphics (WWAN or mSATA capable) So it's weird that I can't get to the Gnome. It looks like drivers aren't working. Is there a way of getting Intel drivers from the command line? Or do you have any other suggestions on what to try next?

  Read the article

• 12.04 wired network doesn't work RTL8111/8168B

  - by laket

  its a fresh 12.04 install 64bits. wifi works fine, wired stays off with cable connected and network-manager shows as if cable is disconnected. Turning off networking lights up my network-cards leds, turning networking on shuts off the leds and no communication is possible. I already tried, turning off the network-manager (sudo service network-manager stop) and setting up my eth0 manually, as soon as I switch off the network-manager my leds light up, but after setting up manually eth0 (sudo ifconfig eth0 10.2.10.114 netmask 255.255.0.0 up) the leds turn off again. I am still dual booting with 10.04 where I have no issues at all, leaving the cable connected all time to my notebook and a switch. Here is some hardware info: lshw: *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:03:00.0 logical name: eth0 version: 03 serial: c8:0a:a9:d7:05:97 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8168d-2.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s resources: irq:42 ioport:2000(size=256) memory:f0004000-f0004fff memory:f0000000-f0003fff memory:f0010000-f001ffff lspci: 02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01) 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) ifconfig eth0: eth0 Link encap:Ethernet HWaddr c8:0a:a9:d7:05:97 inet addr:10.2.10.114 Bcast:10.2.255.255 Mask:255.255.0.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:42 Base address:0xc000 cat /etc/network/interfaces: (already tried here with and w/o eth0) auto lo eth0 iface lo inet loopback cat /etc/NetworkManager/NetworkManager.conf [main] plugins=ifupdown,keyfile dns=dnsmasq [ifupdown] managed=false Any help is welcome ;) Laket

  Read the article

• Boot failure randomly. Can someone help?

  - by desgua

  I often get stuck at the boot on battery. I can suspend and hibernate without any trouble (even on battery). If I plug the energy cable everything goes right most of the time (edited June 13). Adding "acpi=off" doesn't solve the issue. Disabling power save from LAN at BIOS doesn't solve this too. Memory test seems to be ok: I can even compile a kernel without a problem: Has someone a tip for this? (I have the same questions marks in my mind as the image shows if not more :-/ ) obs.: this is an upgraded installation from Natty alpha. edited I (May 22): I've installed a brand new final 11.04 and got the bug again. edited II (June 13): I thought it was solved but it is not. After spending eight days off, the same problem happened even with the power cable connected. I had to reboot about 6 times until success. edited III (June 14): I can boot (even with battery) if I disconnect the cable and take off the battery for a few seconds. This lead me to conclude that maybe something is kept into memory of some hardware. Maybe or maybe not related but I also have touchpad issues (jumps) with this machine. edited IV (June 25): I opened gconf-editor and went to apps gnome-power-manager and disabled everything possibly related to suspend or hibernate. No help. Also I grabbed a Fedora live usb pendrive and got the same problem: So I think it is a hardware problem related issue.

  Read the article

• Cat 6 Only 100mbit speed

  - by Stu2000

  I tried two different cat6 cables directly connected between my two ubuntu machines. This one I ordered online: http://www.amazon.co.uk/gp/product/B002SQPDXS/ref=wms_ohs_product only achieves 100mbit speeds, but does appear to be supporting cross-talk (direct pc to pc), the other cat 6 cable, worked perfectly and gets the full 1gigabit speed. Both tests were performed using ftp and checking the network monitor with direct pc to pc connection. Did the product from amazon lie to me or do I need to manually set a setting somewhere in ubuntu for some cables? I had thought 10 quid for 20m of gigabit ethernet cable was a bit cheap, you get what you pay for... Regards, Stu Update: It seems that after rebooting, the device is set to 1000mbit sec when looking it up with sudo ethtool eth0 However after a while, this will drop down to just 100, after which to reset it to 1000 again, I have to reboot, and simply unpugging and re-plugging in the cable doesn't do it. I tried setting this in networking config file as suggested here: auto eth0 iface eth0 inet static pre-up /usr/sbin/ethtool -s eth0 speed 1000 duplex full but that resulted in my networking failing to start. Is there a problem with my 'auto-negotiation' or something? Can I manually override a setting to 1000mbit?

  Read the article

• More information about worldwide nodes how to get?

  - by Aubergine

  The context: Six hosts across worldwide were traced over week from UK. Ten thousands of lines to be parsed and analysed. And then I try to find any clue of geographical information and path - from where it jumps where. Then after Austria or Germany(each time different) I have mysterious 62.208.72.6 which in GEO LOC gives me Falklands Islands (which is where my target host is by the way, but before target host I still have 5 other nodes) Then I do whois for this 62.208.72.6 route: 62.208.0.0/16 descr: DE-ECRC-62-208-0-0 origin: AS1273 mnt-by: CW-EUROPE-GSOC source: RIPE # Filtered Why it says Europe now? How to understand this enigma code? I want to confirm more or less whether this is in europe or in falkland islands? But it can't be in FK yet as after next two hosts I get New York? Could you also tell me what does this CW-EUROPE-GSOC abbreviation means. (To preserve your sanity better not google, unless you already know it :-D) And the actual whois for the destination/target host, which completely destroys my head: route: 195.248.193.0/24 descr: HORIZON descr: Cable and Wireless Falkland Islands descr: Via Cable and Wireless Communications UK origin: AS5551 mnt-by: AS5551-MNT source: RIPE # Filtered How is it Via Cable and Wireless Communications UK if two nodes before I was in New York? Thank you guys,

  Read the article

• Horse Drawn Fiber Optics Bring Broadband to Remote Areas

  - by Jason Fitzpatrick

  When you think of fiber optics and high speed internet the last thing you likely think of is… horses. Yet horses have been put to use rolling out fiber optics to remote rural locations. In Vermont a Belgium draft horse named Fred, seen in the photo above being tended by his handler Claude, is a distinctly 19th century solution to a 21st century problem; how to run fiber optic cable through remote areas where trucks cannot easily pass. The man and animal are indispensable to cable and phone-service provider FairPoint Communications because they easily can access hard-to-reach job sites along country roads, which bulky utility trucks often cannot. “It just saves so much work – it would take probably 15 guys to do what Fred and Claude can do,” said Paul Clancy, foreman of a line crew from FairPoint. “They can pull 5,000 feet of cable with no sweat.” You can read more about the use of draft horses to draw lines and the roll out of broadband to rural Vermont at the link below. Vermont Uses Draft Horse to Lay Cables for Internet Access [Reuters] How To Encrypt Your Cloud-Based Drive with BoxcryptorHTG Explains: Photography with Film-Based CamerasHow to Clean Your Dirty Smartphone (Without Breaking Something)

  Read the article

• Dell M4600 with nVidia Quadro 2000M hangs on boot when external monitor is connected

  - by vladeta

  I have a problem with my fresh installed Ubuntu 12.04 LTS on my Dell M4600: nVidia quadro 2000M i7-2860 16GB ram 128GB SSD Dell/Samsung 750GB HDD IPS RGB laptop display When it is connected via DP++ to the external Dell U2311H monitor, it hangs on boot or when wakening from suspend. If I detach the DP cable it boots normally. I have tried all combinations that I have found, as adding to grub: "no splash", "boot=pci", "acpi=off", etc... I have also changed in nVidia X settings that external monitor is the primary one and also tried to delete monitor.xml file. There is no change it hangs each time after grub. It starts to load daemons then both screens are blank and then completely hangs with beep sound. What I discovered is if I detach the cable and wait for about 2 sec after grub starts booting and then physically connect DP cable while the Ubuntu is still booting everything works normally and I have a picture on my external screen while the laptop screen is off, just as I wanted. Do you maybe know how to solve this issue? Thank You.

  Read the article

• ubuntu 12.04 LTS hangs on boot when external monitor is connected

  - by vladeta

  I have a problem with my fresh installed Ubuntu 12.04 LTS on my Dell M4600: nVidia quadro 2000M i7-2860 16GB ram 128GB SSD Dell/Samsung 750GB HDD IPS RGB laptop display When it is connected via DP++ to the external Dell U2311H monitor, it hangs on boot or when wakening from suspend. If I detach the DP cable it boots normally. I have tried all combinations that I have found, as adding to grub: "no splash", "boot=pci", "acpi=off", etc... I have also changed in nVidia X settings that external monitor is the primary one and also tried to delete monitor.xml file. There is no change it hangs each time after grub. It starts to load daemons then both screens are blank and then completely hangs with beep sound. What I discovered is if I detach the cable and wait for about 2 sec after grub starts booting and then physically connect DP cable while the Ubuntu is still booting everything works normally and I have a picture on my external screen while the laptop screen is off, just as I wanted. Do you maybe know how to solve this issue? Thank You.

  Read the article

• How to dual boot Ubuntu 12.10 and Windows XP sp3 on Dell Dimension 8250 desktop using 2 hard drives

  - by user106055

  I'd like instructions to dual boot Ubuntu 12.10 and Windows XP (sp3) on my desktop Dell Dimension 8250 (this is old and has 1.5 GB RAM which is maximum). I will be using 2 hard drives. Windows XP is already on a 120 GB drive and and Ubuntu 12.10 will go on a separate 80 GB hard drive. Both drives are IDE using a 80 conductor cable where the 40 pin blue connector connects to the motherboard. The middle connector is gray and is "normally" used for slave (device 1) and the black connector at the very end of the cable is meant for the master drive (device 0) or a single drive if only one is used. First, I do not wish the XP drive to have its boot modified by Ubuntu in any way. It should remain untouched...virgin. Let me know where the XP drive and the Ubuntu drive should be connected based upon the cable I've mentioned above, as well as jumper settings for both during the whole process. I'm just guessing, but should I remove the XP drive and put the empty Ubuntu drive in its place and install Ubuntu? By the way, I already have made the DVD ISO disk. For your information, the BIOS for this machine is version A03. When I tap F12 to get to the boot menu, I have the following choices: Normal (this will take me to a black screen with white type giving me the choice to boot to XP or to my external USB backup recovery drive) Diskette Drive Hard-Disk Drive c: IDE CD-ROM Drive (Note that if the CD Drive is empty, it will then go to the DVD drive) System Setup IDE Drive Diagnostics Boot to Utility Partition (This is Dell's various testing utilities) Thank you in advance for your help. Guy

  Read the article

• TCP/IP RST being sent differently in different browsers.

  - by Brian

  On Mac OS X (10.6), if I start a YouTube video download and pull the Ethernet cable for 5 or so seconds, then plug it back in, I get varying results depending on the browser. With Opera and Chrome, after I plug the cable back in the video continues to load. But with Safari and Firefox, it never does. Using Wireshark to look at the traffic, I found that Opera and Chrome simply ACK the first packet from YouTube after the cable has been plugged back in, but Safari and Firefox set the RST flag (0x4) in the TCP header and no more traffic follows. I can put a HUB in between the machine and the internet connection, the problem goes away and all four browsers continue loading the video when the cable is plugged back into the HUB. Again, looking at the Wireshark logs, it's evident that the machine doesn't see the Mulitcast connection close and there is simply a delay in the packets flowing through. So it seems that if Safari and Firefox sees a Multicast connection close, and then later see data on that same connection, they will send a RST. My question is why? What is the correct course of action, and why are 2/4 browsers doing it one way, while the other 2/4 are doing it another way? Is there somewhere in the code that I can see where this is happening in Firefox, for instance? Thank you very much.

  Read the article

• APC UPS replace battery light and apcupsd reporting "replace battery"

  - by mgjk

  We have an APC Smart UPS 1500. The "Replace Battery" light is on, and apcupsd reports: Emergency! Batteries have failed on UPS xxxx. Change them NOW However, from this article, http://sturgeon.apcc.com/kbasewb2.nsf/for+external/f39c4312fcaf7b948525679a005ebb78?OpenDocument it seems that it's not so clear that the UPS battery needs to be replaced. Stranger, according to the information on the UPS, an 11 minute runtime at 42.9% load running at 27.7V isn't so bad. Any thoughts about what to try next? We're a non-profit, money is an object. It would be a shame to replace a battery with a year or so left in it. # apcaccess status APC : 001,041,1017 DATE : Thu Mar 29 13:01:41 EDT 2012 HOSTNAME : oreilly2 VERSION : 3.14.6 (16 May 2009) debian UPSNAME : xxxx CABLE : Custom Cable Smart MODEL : Smart-UPS 1500 UPSMODE : Stand Alone STARTTIME: Thu Mar 29 12:57:30 EDT 2012 STATUS : ONLINE LINEV : 112.3 Volts LOADPCT : 42.9 Percent Load Capacity BCHARGE : 100.0 Percent TIMELEFT : 11.0 Minutes MBATTCHG : 5 Percent MINTIMEL : 3 Minutes MAXTIME : 0 Seconds OUTPUTV : 112.3 Volts SENSE : High DWAKE : -01 Seconds DSHUTD : 090 Seconds LOTRANS : 106.0 Volts HITRANS : 127.0 Volts RETPCT : 000.0 Percent ITEMP : 23.8 C Internal ALARMDEL : Always BATTV : 27.7 Volts LINEFREQ : 60.0 Hz LASTXFER : No transfers since turnon NUMXFERS : 0 TONBATT : 0 seconds CUMONBATT: 0 seconds XOFFBATT : N/A SELFTEST : NO STATFLAG : 0x07000008 Status Flag SERIALNO : AS0603298896 BATTDATE : 2006-01-14 NOMOUTV : 120 Volts NOMBATTV : 24.0 Volts FIRMWARE : 601.3.D USB FW:1.5 APCMODEL : Smart-UPS 1500 END APC : Thu Mar 29 13:02:12 EDT 2012 Error when running upstest You are using a SMART cable type, so I'm entering SMART test mode mode.type = USB_UPS Setting up the port ... Hello, this is the apcupsd Cable Test program. This part of apctest is for testing Smart UPSes. Please select the function you want to perform. 1) Query the UPS for all known values 2) Perform a Battery Runtime Calibration 3) Abort Battery Calibration 4) Monitor Battery Calibration progress 5) Program EEPROM 6) Enter TTY mode communicating with UPS 7) Quit Select function number: 2 First ensure that we have a good link and that the UPS is functionning normally. Simulating UPSlinkCheck ... YWrote: Y Got: getline failed. Apparently the link is not up. Giving up.

  Read the article

< Previous Page | 12 13 14 15 16 17 18 19 20 21 22 23  | Next Page >