Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 176/370 | < Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >

• how to use iptables to block the IP of device connected to openwrt router

  - by scola

  I have two routers(A,B).the A connect to internet with IP:192.168.1.1 The openwrt router B connect the lan of A by bridge with static IP:192.168.1.111. I am learning to use iptables to control the devices connected to B(wlan) . I use my phone to connect wifi of B,the phone's IP is IP:192.168.1.100.it can surf the internet normally. I want to block the phone's IP to make the phone can not connect to internet. refer to http://bredsaal.dk/some-small-iptables-on-openwrt-tips iptables -A input_wan -s 192.168.1.100 --jump REJECT iptables -A forwarding_rule -d 192.168.1.100 --jump REJECT but it do not work.the phone still connect to internet normally. and I tried other chain(INPUT,OUTPUT,FORWARD).so many chains confused me. iptables -I OUTPUT -o br-lan -s 192.168.1.100 -j DROP and it do not work again. I'm sure that the iptables have no problem. root@OpenWrt:/etc# iptables -L|grep Chain Chain INPUT (policy ACCEPT) Chain FORWARD (policy DROP) Chain OUTPUT (policy ACCEPT) Chain forward (1 references) Chain forwarding_lan (1 references) Chain forwarding_rule (1 references) Chain forwarding_wan (1 references) Chain input (1 references) Chain input_lan (1 references) Chain input_rule (1 references) Chain input_wan (1 references) Chain output (1 references) root@OpenWrt:/etc# ifconfig br-lan Link encap:Ethernet HWaddr 0C:82:68:97:57:BA inet addr:192.168.1.111 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::e82:68ff:fe97:57ba/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:14976 errors:0 dropped:0 overruns:0 frame:0 TX packets:7656 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:2851980 (2.7 MiB) TX bytes:1902785 (1.8 MiB) eth0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:58201 errors:0 dropped:11 overruns:0 frame:0 TX packets:45012 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:54591348 (52.0 MiB) TX bytes:5711142 (5.4 MiB) Interrupt:4 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:312 errors:0 dropped:0 overruns:0 frame:0 TX packets:312 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:39961 (39.0 KiB) TX bytes:39961 (39.0 KiB) mon.wlan0 Link encap:UNSPEC HWaddr 0C-82-68-97-57-BA-00-48-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:4900 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:1223807 (1.1 MiB) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 0C:82:68:97:57:BA UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:37346 errors:0 dropped:0 overruns:0 frame:0 TX packets:49662 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:32 RX bytes:3808021 (3.6 MiB) TX bytes:54486310 (51.9 MiB) root@OpenWrt:/etc/config# cat network config 'interface' 'loopback' option 'ifname' 'lo' option 'proto' 'static' option 'ipaddr' '127.0.0.1' option 'netmask' '255.0.0.0' config 'interface' 'lan' option 'ifname' 'eth0' option 'type' 'bridge' option 'proto' 'static' option 'ipaddr' '192.168.1.111' option 'netmask' '255.255.255.0' option 'gateway' '192.168.1.1' option dns 192.168.1.1 and how to use iptables to control the network of wlan? Thanks in advance and sorry for poor English.

  Read the article

• Simulating network latency for localhost connection on Windows 7

  - by nitro2k01

  I need to simulate network latency to a program running on the local computer, connecting to a local service. Thus far I have tried dummynet (a windows build of ipfw) which I got working after some trial and error. While it generally works, I can't seem to get it to filter localhost traffic. Even after adding a rule from any to any which affects external traffic, this makes no difference for local connections. I would appreciate if anyone knows how to simulate local latency using dummynet or a different tool. The tool should be able to simulate latency generically in IP packets, (TCP and UDP) and not be protocol specific.

  Read the article

• DHCPD (Slackware) - Disabling auto-generation of gateway as DNS server

  - by Dogbert

  Good day, I am using a Linux workstation on Slackware 13.37. One "problem" I have had to deal with ever since 11.0 is the following: DNS servers are queried and determined at startup by DHCP daemon (DHCPD) This is invoked at startup by a script located at /etc/rc.d/rc.dhcpd My DNS servers for my ISP are resolved correctly, and are stored in a list located at /etc/resolv.conf However, the one annoying problem is that my gateway IP (ie: 192.168.1.1) is always automatically put at the top of the list in resolv.conf, meaning I have to always wait for a timeout before a valid DNS server is used to resolve an address (ie: timeout on 192.168.1.1 because it is not actually a DNS server, then DHCP uses the next server in the list). I could lower my DNS resolution timeout so the gateway query times out quicker, but that's not what I want, as I don't want to degrade the abilities of legitimate DNS servers. What I would like to do is change how DHCPD operates so that it does NOT put my gateway IP address at the beginning of this list. I've searched via "man dhcpd", etc, and haven't found the exact answer yet. Any help on this issue is appreciated. Thank you all in advance for your time and assistance.

  Read the article

• No internet on some devices, still on WiFi

  - by Joost

  Ok, here's the situation. I live with 3 friends, and we often sit in the living room with laptops out. There's a WiFi router in the kitchen, and we have quite a stable connection. The issue, however, is this: sometimes, all of a sudden one of my friends loses internet connection. Even disconnecting/reconnecting to the WiFi network does not help. When we restart the router, though, it works like a charm again. The odd thing is, it happens just for this one Windows 7 laptop. We've switched routers (for a different reason) in the mean time, but the issue remained. This makes me suspect the laptop even more. I realise I've given little details, but I don't really know what to try/do. Any suggestions what it might be?

  Read the article

• Does WCN (Windows Connect Now) work on Windows 7?

  - by WilliamKF

  I'm trying to add a Canon printer wirelessly and I can't just enter the WEP settings, I'm forced to use this WCN which is says is in Vista, but I'm not finding it on Windows 7. Where can I find this in Windows 7?

  Read the article

• Meaning of Bridge-Check in iptables flowchart

  - by networkIT

  In the famous iptables flow-chart what does bridge-check exactly stands for ? I couldn't find any documentation. The only clue I found was while scanning the MikroTik RouterOS documentation ( RouterOS is build upon a Linux 2.6.16 kernel ), I found this : In-interface Bridge = Checks if the input interface is a port for a bridge or is the bridge. Manual:Packet Flow Comparing both flow-charts brings clues that iptables Bridge-check might equal MikroTik In-Interface Bridge. Is this true ? Else, what might be the meaning of iptables Bridge-Check ?

  Read the article

• Creating a really public Windows network share

  - by Timur Aydin

  I want to create a shared folder under Windows (actually, Windows XP, Vista, and Win 7) which can be mounted from a linux system without prompting for a username/password. But before attempting this, I first wanted to establish that this works between two Windows 7 machines. So, on machine A (The server that will hold the public share), I created a folder and set its permissions such that Everyone has read/write access. Then I visited Control Panel - Network and Sharing Center - Advanced Sharing Settings and then selected "Turn off password protected sharing". Then, on machine B (The client that wants to access the public share with no username/password prompt), I tried to "map network driver" and I was immediately prompted by a password prompt. Some search on google suggested changing "Acconts: Limit local account use of blank passwords to console logon only" to "Disabled". Tried that, no luck, still getting username/password prompt. If I enter the username/password, I am not prompted for it again and can use the share as long as the session is active. But still, I really need to access the share without any username/password transaction whatsoever and this is not just a convenience related thing. Here is the actual reason: The device that will access this windows network share is an embedded system running uclinux. It will mount this share locally and then play media files. Its only user interface is a javascript based web page. So, if there is going to be any username/password transaction, I would have to ask the user to enter them over the web page, which will be ridiculously insecure and completely exposed to packet sniffing. After hours of doing experiments, I have found one way to make this happen, but I am not really very fond of it... I first create a new user (shareuser) and give it a password (sharepass). Then I open Group Policy Editor and set "Deny log on locally" to "A\shareuser". Then, I create a folder on A and share it so that shareuser has Read access to it. This way, shareuser cannot login to A, but can access the shared folder. And, if someone discovers the shareuser/sharepass through network sniffing, they can just access the shared folder, but can't logon to A. The same thing can be achieved by enabling the Guest user and then going to Group Policy Editor and deleting the "Guest" from the "Deny access to this computer from the network" setting. Again, Guest can mount the public share, but logging in to A as Guest won't be possible, because Guest is already not allowed to log in by default. So my question would be, how can I create a network share that is truly public, so that it can be mounted from a linux machine without requiring a password? Sorry for the long question, but I wanted to explain the reason for really needing this...

  Read the article

• Flow of packets in network

  - by user58859

  I can't visualize in my mind the network traffic flow. eg. If there are 15 pc's in a LAN When packet goes from router to local LAN, do it passes all the computers? Does it go to the ethernet card of every computer and those computers accept the packet based on their physical address? To which pc the packet will go first? To the nearest to the router? What happens if that first pc captures that packet(though it is not for it)? What happens when a pc broadcast a message? Do it have to generate 14 packets for all the pc's or only one packet reach to all pc's? If it is one packet and captured by first pc, how other pc's can get that? I can't imagine how this traffic is exactly flows? May be my analogy is completely wrong. Can anybody explain me this?

  Read the article

• SQUID Transparent SSL proxy (no intercept)

  - by user974896

  I know how to have squid work as a transparent proxy. You put it into transparent mode then use your router or IPTABLES to forward port 80 to the squid port. I would like to do the same for SSL. Every guide I see mentions setting up keys on the squid server. I do not want squid to actually decrypt the SSL traffic then establish a connection with the server, rather I would like squid to simply forward the SSL traffic as is. The only thing I would like to do is be able to check the SSL request for any offending IPs and drop the packets if the destination is one of them.

  Read the article

• ip conflict error

  - by mhay

  how to resolve ip conflict error ? i m getting my server's ip address when i m downloading from rapidshare ? and my ip address is different.

  Read the article

• Connecting via ShrewSoft VPN client means no LAN internet access (Windows 7 64 bit) - any advice please?

  - by iwishiknewmoreaboutnetworking

  I have a Windows 7 64 bit desktop machine which is connected to a LAN. I recently installed ShrewSoft VPN client v 2.1.7 on my machine so that I can connect to a license server hosted by my customer. They are running a Cisco VPN server and I originally tried (unsuccessfully!) to use the Cisco VPN client for Windows 64 bit but the default gateway wasn't being configured correctly after loading in my pcf file. Using ShrewSoft I am able to import the same pcf file, and successfully connect to the machine I need to using the VPN client software. The client machine I need to connect to has IP address 1.52.90.33. The problem is that when I am connected to the customer network using the VPN client application (and after a few minutes) I lose my LAN internet connection. I can only presume that this is because, by default the ShrewSoft VPN client application automatically tunnels all traffic through the VPN connection. I know there is an option to switch off the "Tunnel All" option on the Policy tab of the application and enter a Remote Network Resource (to "Include" or "Exclude") as "Address" and "Netmask" IP addresses however I am not sure what I need to enter here. Here is my ipconfig output before connecting to the VPN (with suffixes blanked out): Windows IP Configuration Ethernet adapter Local Area Connection: Connection-specific DNS Suffix . : ***.*** Link-local IPv6 Address . . . . . : fe80::8de3:9dbe:393a:33ba%11 IPv4 Address. . . . . . . . . . . : 150.237.13.17 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 150.237.13.1 Tunnel adapter 6TO4 Adapter: Connection-specific DNS Suffix . : ***.*** IPv6 Address. . . . . . . . . . . : 2002:96ed:d11::96ed:d11 Default Gateway . . . . . . . . . : 2002:c058:6301::c058:6301 Tunnel adapter Local Area Connection* 9: Connection-specific DNS Suffix . : IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:2cf9:38c4:6912:f2ee Link-local IPv6 Address . . . . . : fe80::2cf9:38c4:6912:f2ee%12 Default Gateway . . . . . . . . . : Tunnel adapter isatap.***.***: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : ***.*** Here is my route print output before connecting to the VPN: =========================================================================== Interface List 11...20 cf 30 9d ec 2a ......Realtek RTL8168D/8111D Family PCI-E Gigabit Ethern et NIC (NDIS 6.20) 1...........................Software Loopback Interface 1 14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter 12...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 150.237.13.1 150.237.13.17 2 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 150.237.13.0 255.255.255.0 On-link 150.237.13.17 257 150.237.13.17 255.255.255.255 On-link 150.237.13.17 257 150.237.13.255 255.255.255.255 On-link 150.237.13.17 257 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 150.237.13.17 257 255.255.255.255 255.255.255.255 On-link 12

  Read the article

• Aircrack-ng Usage on Windows (XP) -- Needs clear steps

  - by Alvin

  I've found that Aircrack-ng is very powerful tool for wireless hacking. But it is a bit complicated to use (even with its documentation). Also, when I run the GUI, it needs to add a "capture file". What is that? Additionally, it says Windows version is weaker than the Linux version. So how can I get it to run like a Linux version? What are some step-by-step instructions (to use on Windows XP)?

  Read the article

• Linux bonded Interfaces hanging periodically

  - by David

  I've several hosts that are showing problems with connectivity. When working from the command line, for example, typing is frozen for a second or so, then recovers - then it does it again. The most egregious example host would freeze (input) for 15-30 seconds, then recover and go out 5 seconds later. Switching cables didn't do anything - but removing one of the physical cables caused everything to clear up instantly (which why I think this is a network problem). Looking at the network I couldn't see any packets floating that would explain this. These ethernet interfaces (Gigabit Dell) were working normally previously, but since we moved the systems - and put them on a new set of switches - this has been a problem on multiple theoretically identically-configured hosts. The original switches were an HP Procurve 1810-24G and an HP Procurve 1800-24G connected with LLDP; the new switches are both Cisco SG 200-26, which I understand are rebranded Linksys switches. Is this caused by a problem with the switches? Is it the switch configurations? Are the Cisco switches incapable of handling this? I don't see where the configuration is located; I searched the usual /etc/sysconfig/network/devices but there's nothing in there about options (like mii polling) and nothing about the method of balancing the two. Searching scripts, I can't find anything in /etc/init.d/network either. The hosts are almost all Red Hat Enterprise Linux 5.x systems (5.6, 5.7) but some are Ubuntu Server 10.04.3 Lucid Lynx. I need help with both if it comes to that. UPDATE: We're also seeing some problems with servers on the original switches. The HP switches and the Cisco switches are also interconnected (temporarily); there is a cable run from one switch to the next. Pings on any of these hosts show about one ICMP packet out of every 5-6 getting dropped (timed out). Could there be an interaction between the two switches? Oh, and the hosts are using bonding with Balance-RR as the method.

  Read the article

• Accesing internet with Host-Only network VirtualBox

  - by Bibo

  I have two VMs in my VirtualBox. Both are FreeBSD and should communicate between each other. I have created network with DHCP enabled and set like this: Server Address 10.10.10.1 Server Mask 255.255.255.0 Lower Address Bound 10.10.10.100 Upper Address Bound 10.10.10.200 My VMs are pinging each other and getting right ip adress. This is what I must have and can´t change. Now I want to access internet from one VM and I found that I must use two network cards but I don´t know how to set the second one. I am new with VirtualBox and this stuff so if you count with this in you answer I would appreciate that. And I have Windows 8 as host system if it´s matter.

  Read the article

• Logitech MX3200 keyboard stopped working

  - by Roy Rico

  I have a Logitech MX3200 wireless keyboard and mouse set, and keyboard stopped working. I was working with it and it just stopped in the middle of using it. Some notes: The mouse still works flawlessly, i've tried to reconnect the KB i've tried to reconnect everything, mouse reconnects, keyboard reconnects (or pretends to) I've tried to hard reset (holding the connect button on the receiver for 10 seconds). I've tried new batteries I took out the batteries out of the KB & Mouse and unplugged the receiver over night. The media keys still work (launches winamp) but they main keys does not At this point, i've tried everything I've seen online. I just want to know is my keyboard dead in the water? I would say it's been about 8 months to a year since i've bought it, and the articles i find on the internet all say that's as long as they last... is this true? what's everyone's experience? I hope it's not true.

  Read the article

• Local or public NTP servers?

  - by BeeOnRope

  For a relatively large network (thousands of hosts) - what are the arguments for and against running a locally managed (pool of) NTP server(s) (perhaps periodically set via some public NTP server) and having all other hosts on the network use that (pool of) NTP server(s) versus having all hosts simply use public NTP servers directly, say via ntp.pool.org? Aside from the pros and cons, What is typical best practice today?

  Read the article

• How can I control wireless networks in Ubuntu without Network-Manager?

  - by Solignis

  Hi there, I recently installed Ubuntu on a laptop I got. I was having issues with the network manager just like I was having in my VM where it was not setting up the hostname correctly. Anyhow now I have a problem, since it is a laptop it will be moving.... But I have no way to discover new wireless networks. Anyway I can gain that functionality back? The problem I am running into is that I need to set the DNS search and domain for the machine so I can access my network but the network-manager was overriding the settings. Any help would be much appreciated.

  Read the article

• Log ports opened by an application

  - by Simon A. Eugster

  I'm searching for something like: tcpdump -p PID # But tcpdump does not know the PID or lsof -i --continuous # But lsof just runs and exits, no «live logging» to log which connections an application opens. In my case, I want to find out to which port git connects when committing. This happens in a fraction of a second, so I cannot use lsof. If there is a lot of traffic, filtering by PID or process name would be useful.

  Read the article

• Connecting a print/file server with no wired access

  - by PeanutsMonkey

  We currently have a printer server which also serves as a file server. The server is located on premise however is not close to any wired access point i.e. a patch panel or point. The server also requires access to the Internet as it transmits files across. We have a wireless modem and a wireless router. I can run a cable between the server and wireless router. How can I have the wireless router communicate with the wireless modem? If the operating system of the server is concerned, it is running Windows Server 2003.

  Read the article

• What is the difference between UDP and TCP?

  - by Guy

  My router has two protocols (and a "both" option) that I can select when setting up port forwarding: UDP and TCP. What is the difference between these two protocols and when would you select one over the other in port forwarding?

  Read the article

• Best way to segment traffic, Vlan or subnet

  - by thebird

  We have a medium sized network of around 200 nodes and are currently in the process of replacing old daisy chained switches with stack-able or chassis style switches. Right now our network is broken up via subnet; production, management, IP, etc each on a separate subnet. Does anyone have an opinion on whether creating Vlan's instead of subnets would be more beneficial? Our general goal is to prevent bottlenecks, separate traffic for security, and to manage traffic with more ease.

  Read the article

• How do I prevent internet access to a group of computers on my network?

  - by Kevin Boyd

  Well I have the following setup... Computer A , B and C are networked.... Computer A is connected to the internet, computer B and C are not setup for internet access currently but I guess its possible with some kind of setting they would eventually be able to access the internet and this is what I would like to prevent. In summary only A should have internet access while A and B and C should still be on intranet. Is this kind of config possible?, what kind of software or setup or tools would I need to achive this?

  Read the article

• Access server using IP on another interface

  - by Markos

  I am using Windows Server 2012 instead of a router for my home network. Currently I am using RRAS and computers from local network can access Internet correctly. Here is a map of the current setup: [PC1] ---| |---- (lan ip)[Server](wan ip)--> internet [PC2] ---| I have applications running on Server, such as IIS and others. All can be accessed from internet using wan ip and from lan using lan ip. I have a domain, lets say its my-domain.com, which is resolved to my wan ip. What I want is to enable my LAN computers to be able to connect to services on my server using the very same address as internet users: eg http://my-domain.com/. However this does not work for my lan computers. What I understand is that I need to set up some kind of loopback route in a way that packets comming to LAN interface get routed to WAN interface. But I haven't found how to achieve this (in fact, I don't know WHAT to search for). Feel free to ask for additional informations and I will try to update the question.

  Read the article

• Cannot save properly the source of .html file containing Russian letters as .txt

  - by brilliant

  When I save the source of this page of a Russian website: http://www.mail.ru/ as a .txt file, all Russian letters turn into Chinese characters (I am working on a Chinese computer at the moment), but when I save another page of another Russian website: http://starling.rinet.ru/cgi-bin/response.cgi?root=/usr/local/share/starling/morpho&morpho=0&basename=\usr\local\share\starling\morpho\ozhegov\ozhegov&first=4001 also as a .txt file, all Russian letters are saved in it as the are. Why is it so?

  Read the article

• Prevalence of WMI enabled in real Windows Server networks

  - by TripleAntigen

  Hi I would like to get opinions from systems administrators, on how common it is that WMI functionality is actually enabled in corporate networks. I am writing an enterprise network application that could benefit from the features of WMI, but I noted after creating a virtual network based on Server 2008 R2, that WMI seems to be disabled by default. Do systems admins in practical corporate networks enable WMI? Or is it usually disabled for security purposes? What is it used for if it is enabled? Thanks for any advice! MORE INFO: I should have said, I really need to be able to query the workstations but I understand that by default the WMI ports on Win7 and XP firewalls (at least) are disallowed, so do you use some sort of group policy or other method to leave a hole open for WMI on the workstations? Or is just the servers that are of interest? Thanks for the responses!!

  Read the article

< Previous Page | 172 173 174 175 176 177 178 179 180 181 182 183  | Next Page >