Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 177/370 | < Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >

• Logitech MX3200 keyboard stopped working

  - by Roy Rico

  I have a Logitech MX3200 wireless keyboard and mouse set, and keyboard stopped working. I was working with it and it just stopped in the middle of using it. Some notes: The mouse still works flawlessly, i've tried to reconnect the KB i've tried to reconnect everything, mouse reconnects, keyboard reconnects (or pretends to) I've tried to hard reset (holding the connect button on the receiver for 10 seconds). I've tried new batteries I took out the batteries out of the KB & Mouse and unplugged the receiver over night. The media keys still work (launches winamp) but they main keys does not At this point, i've tried everything I've seen online. I just want to know is my keyboard dead in the water? I would say it's been about 8 months to a year since i've bought it, and the articles i find on the internet all say that's as long as they last... is this true? what's everyone's experience? I hope it's not true.

  Read the article

• Accesing internet with Host-Only network VirtualBox

  - by Bibo

  I have two VMs in my VirtualBox. Both are FreeBSD and should communicate between each other. I have created network with DHCP enabled and set like this: Server Address 10.10.10.1 Server Mask 255.255.255.0 Lower Address Bound 10.10.10.100 Upper Address Bound 10.10.10.200 My VMs are pinging each other and getting right ip adress. This is what I must have and can´t change. Now I want to access internet from one VM and I found that I must use two network cards but I don´t know how to set the second one. I am new with VirtualBox and this stuff so if you count with this in you answer I would appreciate that. And I have Windows 8 as host system if it´s matter.

  Read the article

• Ubuntu 10.04 network manager issues

  - by Shark

  I was using the default network manager to connect to my wi-fi network, but if the connection is dropped or router restarted the network manager wont reconnect automatically after i guess a couple of tries and just gives a pop-up to connect manually . To avoid this annoyance I installed WICD but though it does try to reconnect to the network after a drop in connection it is unable to resolve the ip address and i am left with an even bigger annoyance . 1. Is there a way to counter either of these issues ? 2. Something like a background process that will check network status periodically and then try to connect to a favored network ? Edit- out put of lshw -C network *-network description: Wireless interface product: Broadcom Corporation vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:12:00.0 logical name: eth1 version: 01 serial: c0:cb:38:18:9b:7f width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.60.48.36 ip=192.168.11.2 latency=0 multicast=yes wireless=IEEE 802.11 resources: irq:17 memory:fbc00000-fbc03fff *-network description: Ethernet interface product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:13:00.0 logical name: eth0 version: 02 serial: f0:4d:a2:94:2d:74 size: 10MB/s capacity: 100MB/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list rom ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half latency=0 link=no multicast=yes port=MII speed=10MB/s resources: irq:29 ioport:e000(size=256) memory:d0b10000-d0b10fff(prefetchable) memory:d0b00000-d0b0ffff(prefetchable) memory:fb200000-fb21ffff(prefetchable)

  Read the article

• Network switching issues with MacOS 10.7?

  - by Denis

  I'm having a wired problem and hope somebody can tip me, what way should I dig to. I'm using MacBookPro with Lion 10.7.3 both at my working place & at home. At working place, we have a domain-based network with 802.1x authorization (more than 400 computers) and to connect it I'm using Ethernet cable. IP range is 10.10.2.*. All network settings are setup automatically by DHCP. Also, in settings, I have Network Account Server setup in the User&Groups Settings for my work Domain server - and it is available only from corporate network. At home, I have an ADSL router, that shares Internet connection by WiFi in NAT mode. I'm using WiFi to connect it. Router gives out addresses from 192.168.1.* range and all settings are also set up by router's DHCP. So, my problem is the following. When I come back home from the office, I open my MacBook and AirPort automatically connects my WiFi network. After this, for about 1 minute I'm able to browse sites & ping hosts successfully. But after this minute, network connection is broken down. All pings return time-out. trace route to google.com stops on 192.168.1.1 (which is my router). This lasts for 3-4 minutes. After that network connection is automatically repaired and all pings go smoothly again. At the same time, when my MacBook return timeouts, I can successfully ping any host from my wife's MacBook - so this doesn't look like router issue. When I come to the office, I don't have any issues and Internet connection is available & stable moments after ethernet cable plugged in. Do anybody has any clues about this? What should I monitor & what settings look for resolving this issue? Please, ask, what additional information should I provide. Hoping for good advice & thanks in advance!

  Read the article

• How to analyze a wifi network with many devices

  - by Caveatrob

  My friend has a wifi network with an x-box, a wii, a playstation, and two nintendo portables. She's also got 2-3 PC's and a network printer. She's got a wifi repeater as well. She claims that she didn't have any issues for months with everything working together, and suddenly everything stopped disconnecting. I haven't been over there yet - wanted to figure out the best way to diagnose the thing. I asked her to send me the stats on the booster and the modem, etc: The booster is Netgear serial #2ac2195506b95 The modem is Cisco Linksys e1500 #10910c12129103 We have a sprint router thru centurylink and they said it is working fine 660 series

  Read the article

• Problem connecting to Ubuntu Server in same local network.

  - by frbry

  I have my LAN set up as below: 192.168.2.1: ADSL Router (DHCP Range: 192.168.2.2-192.168.2.250) 192.168.2.254: Wireless Access Point 192.168.2.253: Ubuntu Server (Static IP) 192.168.2.2: My Laptop (Connects to Internet via the Wireless AP) NAT in router is active and set up to transfer requests made over port 80 to 192.168.2.253. Router's firewall is inactive. No IPs in DMZ. My friends get Apache's It Works page when they try to enter http://my_external_ip. But I get Router's configuration page instead of that. What should I check or do? Thanks.

  Read the article

• Where would an S3 upload speed cap originate?

  - by CoreyH

  I do a ton of uploading to S3 and am experiencing capped speeds and I can't quite figure out how to address it. The setup: Windows Server 2008 R2 x64, external HD, using a Java based upload tool called Jsh3ll and custom VBS scripts to kick the jobs off. Running one process at a time, I am always limited to about 4mbps. I have FiOS at 35/35mbps speeds, so it isn't an outright limit. AND, I can run parallel instances and can go all the way up to 35mbps, so I know the problem isn't gateway/nic/machine/amazon related. Running parallel instances works to a degree as a solution, but increases the complexity of my workflow greatly. Solving this would make my life dramatically easier. When I was first doing this I was playing around with a bunch of Windows TCP parameters and was able to briefly get unconstrained bandwidth, but it wasn't repeatable. Thoughts?

  Read the article

• Enable/disable wireless interface in a bat file

  - by Herms

  Is there a way to enable/disable a wireless network interface via the command line (so I can put it in a bat file)? When I'm in the office I use a wired connection, but Windows still occasionally bugs me about my wireless connection not being connected (even though I turned off the option for notifying me when there's no connectivity). I'm guessing the only way to stop it from bugging me is to disable the interface, but I'd rather not have to go into the network settings every time I need to do so. I'd like to set up a bat file or a shortcut that I can use to enable/disable the wireless (preferably a single one that toggles the current state), and then just set up a keyboard shortcut for that. I just have no idea how to do so from the command line.

  Read the article

• Using Credentials with network scanners

  - by grossmae

  I'm testing out both Tenable's Nessus scanner as well as eEye's Retina for scanning network devices. I am trying to supply credentials to get deeper, more accurate results, however there seems to be no difference in the results whether I supply the credentials or not. I've read the documentation and it seems like I've tried all the logical settings in the Credential options. I've submit along with usernames and passwords for many different accounts and types of accounts (both SSH Credentials and Web Application Credentials) on the devices as well as their respective domain names (when applicable). Is there possibly a good test for either (or both) scanners to tell where these credentials are being provided (if at all) and if any of them are successfully getting authentication?

  Read the article

• Cannot increase MTU on gigabit network

  - by RayQuang

  Hi, I have just set up my new gigabit network and when I was about to increase the MTU to use jumbo frames, I get this error: root@rayquang-desktop:~# ifconfig eth1 mtu 9000 SIOCSIFMTU: Invalid argument Could anyone help me to increase the MTU. Details: NIC: NETGEAR GA311; Switch: NETGEAR GS105, running Ubuntu 10.10 and Debian Lenny on desktop, server respectively. Help would be greatly appreciated, RayQuang

  Read the article

• How can I create a VLAN on my extreme switch for a seperate subnet/domain?

  - by drpcken

  I'm putting together a small active directory implementation for a buddy of mine. I currently have 2 servers (one is the primary domain controller) and a couple clients. I need to test and run updates on every machine on this domain, but I would have plug them into my current LIVE domain to get it internet access. From what I've read having two separate domains on a single subnet is a bad idea (even though it is temporary) so I don't want to risk messing anything up on my production domain. I'm pretty sure I can create a separate VLAN on my extreme 48 port switch and plug this smaller domain into it on a different subnet, but I don't know the commands. Both subnets would need internet access of course (one of the things I can't wrap my head around is routing internet traffic between subnets (gateway is on production subnet). My production domain is on subnet 192.168.200.0. My new domain I want to put online would go into subnet 192.168.10.0. A shove in the right direction would be greatly appreciated. Thank you!

  Read the article

• How to fix unstable RJ45 jacks? [closed]

  - by BeemerGuy

  This is a little project I'm doing at home. I wanted to wire two rooms together (basically, the router is one room, and the switch is in the second room). So I ran a CAT5 between the two rooms, and wired an RJ45 jack in each room. I then hooked up the two jacks with two CAT5 cable to run it through the cable tester, and all 8 wires seem good. Now, when I connect the switch and the router, the connection is unstable -- I ping the router and it barely holds on for two pings before it disconnects, and stays in that unstable state. Just to make sure the router and the switch are ok, I connected them with long wire between the two rooms and the connection is absolutely stable, and pings continuously. What could be the cause for the unstable connection? Especially that it pings a few times, so there IS a connection. But why is it unstable? And how come the cable tester says it's ok, but it's unstable?

  Read the article

• xtreamer doesn't see Window 7 shares

  - by Assaf Lavie

  Weird situation after reinstalling Windows 7 on my PC. Suddenly the xTreamer (media streamer) that's connected to the same LAN doesn't see shares by my PC. Other PCs (and even a MacBook) on the same network can access these shares just fine. And the xTreamer is capable of seeing other shares in the network (e.g. by some other NAS server I have). It can't be permissions/firewall because the Mac does connect to the shares... I'm stumped. Ideas?

  Read the article

• Looking for a router with multiple WAN ports and load balancing

  - by Cyrcle

  I'm going to be moving in a few months. The location I'm moving to is great except it's on a road with very few people, so the internet access option is limited to DSL at 1.6Mbps down, 384kbps up. This is much slower than I'm used to. One option is to get at least two of the DSL lines. There's also good possibility that I'll be able to get WiMax or similar. I've been looking around a bit and it seems like what I need is a load balancing router with multiple WAN ports. Can anyone recommend some good ones? I could also go with a small power efficient Linux box with multiple NICs. What would be good software for that? It'd need to be able to handle around 10Mbps. Thanks for any help

  Read the article

• Hiding mapped drives for all users but letting programs access them

  - by AgainstClint

  What I'm looking for (and not sure if it's possible) is that we have 16 mapped network drives that are mapped when any user logs on, what I would like is to cut this down to just one visible drive yet leaving the other ones still usable to certain programs. I would just un-map them, however one of our constantly used programs writes to almost all of the drive letters so they need to be mapped for just that program, however they do not need to be visible to the user. Is this possible?

  Read the article

• Ubuntu Connect Button Disabled, cannot connect

  - by CSharperWithJava

  I'm trying to connect to my school network from Ubuntu 12. The network is WPA encrypted and I can connect just fine if the network manager establishes a connection automatically. However, when I get disconnected and try to reconnect a username and password prompt pops up. The credentials are already stored and are autofilled in correctly, but the Connect button is disabled so I can't actually connect to the network. What can I do? The only guess I've found so far is the password is too short and Ubuntu is expecting a full WPA key. I don't administer the school network though so I certainly can't change that.

  Read the article

• How to set static ip address on vmware for NAT guest vms from an ubuntu Host dhcp server?

  - by javadba

  I need to configure various linux flavor NAT'ed guest vm's to have static ip addresses provided by the Ubuntu host. The vmware documentation punts on this topic, deferring to "see the man pages for your linux distribution". But the generic pages for "my linux distro" do not know about the special stuff for vmware e.g. vmnet8. Pointers from someone who just knows how to do this would be much appreciated. Here is the /etc/vmware/vmnet8/dhcpd/dhcpd.conf: allow unknown-clients; default-lease-time 1800; # default is 30 minutes max-lease-time 7200; # default is 2 hours subnet 192.168.238.0 netmask 255.255.255.0 { range 192.168.238.128 192.168.238.254; option broadcast-address 192.168.238.255; option domain-name-servers 192.168.238.2; option domain-name localdomain; default-lease-time 1800; # default is 30 minutes max-lease-time 7200; # default is 2 hours option netbios-name-servers 192.168.238.2; option routers 192.168.238.2; } host vmnet8 { hardware ethernet 00:50:56:C0:00:08; fixed-address 192.168.238.1; option domain-name-servers 0.0.0.0; option domain-name ""; option routers 0.0.0.0; } Fromt the dhcpd.conf documentation, we are supposed to add an entry for static hosts similar to the following: host mystatichostonee { hardware ethernet 00:20:6B:C7:9B:E4; fixed-address 192.168.238.101; } host mystatichosttwo { hardware ethernet 00:23:7a:C7:9c:F2; fixed-address 192.168.238.102; } But notice that the vmnet8 entry in the vmware-generated dhcpd.conf already is set to fixed-address. I don't know how to add the specifics for my hosts to that vmnet8 entry: do they become nested?

  Read the article

• unable to connect to remote sql server from SHDSL router

  - by user529265

  Got a new leased line network to our office that came with a SHDSL router (Watson). Currently, we are unable to use Sql Server management studio to connect to remote Sql databases. It errors out saying A connection was successfully established with the server, but then an error occurred during the pre-login handshake. (provider: TCP Provider, error: 0 - The specified network name is no longer available.) (Microsoft SQL Server, Error: 64) I logged into the Watson management panel and unblocked all the ports for TCP traffic (specified the range as 0 to 60000 and UDP as well - this include 1443 required for connecting to SQL Server). The router is the only thing that has changed. We are able to connect to it from other networks just fine. Is there something we are missing here. Any help would be greatly appreciated.

  Read the article

• RS-232 vs. RS-485

  - by user60524

  Doing a little research on the two to figure out which one may better suit my purposes (communications amongst different hardware). How do they fare against one another? Im far from being a specialist and have no idea where I would even start looking for data to compare and contrast. If possible can someone please answer the following questions in regards to each of these. Can they be networked amongst each other? Can they be easily networked over ethernet? What speeds do they transfer at? (Min, Max, Etc.) Reliability? Best framework to build on top of to support the above? Any standard communications programs? Debugging capability? Any help would be very much appreciated, thanks.

  Read the article

• Too many Tunnel Adapter Interfaces

  - by Tomas Lycken

  If I open a command prompt on my machine and type ipconfig /all, I see lots of Tunnel adapter Local Area Connection* 9: Media state . . . . . . . . . . . . . : Media disconnected Connection-specific DNS Sufficx . . . : Description . . . . . . . . . . . . . : Microsoft 6to4 Adapter #5 Physical address. . . . . . . . . . . : 00-00-00-00-00-00-00-E0 DHCP Enabled. . . . . . . . . . . . . : No Autoconfiguration Enabled . . . . . . : Yes In fact, they're so many that my "real" adapters are pushed out of the stack, and can't be seen anymore. Is there any flag I can use on ipconfig to hide all virtual interfaces? Or is there some other way around this problem? Since they always say "Media disconnected" I suppose disabling could be an option, but if possible I'd rather not turn any functionality off. I just want to control what output I get from ipconfig. Also, I know these are related to IPv6 stuff. However, most of what I find on google merely states what these are, and that they're harmless - nothing about hiding/removing them.

  Read the article

• Superscope DHCP leases and configuration set up

  - by Vdub

  Hello I wanted to see if someone could help with a network problem I am having. Right now we have a super-scope and scopes of 192.168.50.1 and 192.168.51.1, as of now both are activated but only 192.168.50.1 is handing our leases, 192.168.51 wont. here is a summary of our network Gateway: watchguard firebox x750e for our router/gateway at 192.168.50.1 I set up as a secondary IP address 192.168.51.1 Server: Server 2008 r2 standard, running our DNS @ 192.168.50.242 and 8.8.8.8 as a secondary, AD, and DHCP. On that NIC card i have 192.168.50.242 as the IP address and 192.168.51.242 as a secondary. 192.168.50.1 as the default gateway and 192.168.51.1 as a secondary. Im am not very knowledgeable at this but as far as i have researched after adding a super scope and activating scopes, they should automatically start handing out addresses and I cant figure out why only one does. any help at all would be appreciated.

  Read the article

• Proxy the traffic in http and https from my iPhone/iPad to VirtualBox on my Mac

  - by Nicolas BADIA

  I've got a mac running a Debian VirtualBox which forward the traffic from 8080 on the mac to 80 in the box and from 8443 to 443. The domains with the extension .dev are redirected on the mac to 127.0.0.1 with dnsmasq. The traffic on IP 127.0.0.1 is forwarded from 80 to 8080 and from 443 to 8443 using ipfw. So with this settings, my Debian VirtualBox gets all the traffic of my .dev domains in http or https. What I want is to be able to proxy the traffic of my .dev domains in http and https from my iPad to my Debian VirtualBox on the mac. I've try to setup an HTTP proxy on the ipad but I can only do it for one port (and it's not working with the port 443). Any idea on how I could achieve that ?

  Read the article

• How to access an node of an LAN via WAN?

  - by gilzero

  Lets say I have a router that is connected to the Internet. An WAN IP address is given by ISP. It is using PPPoE ADSL, the IP address is not static, every time it connected, assigned a different IP address. There is an web server 192.168.0.100 running in the LAN. I heard something like DMZ + DynDNS can do the job? But not sure what these are and how they work. Any there way(s) to access the local node 192.168.0.100 via WAN, so that I can reach that node even I am not home. Thanks for any advice.

  Read the article

• Is there a standard method for assigning nameservers to servers in a Windows domain?

  - by HopelessN00b

  As the title asks, I'm wondering if there's any standard or "best practice" for how to actually assign nameservers (DNS) and manage the nameserver configuration for client servers on a Windows domain. I'm talking about the setting circled in the below image, in case the language of the question is not clear enough: This is for a large, multi-site environment, where ideally/hopefully all servers point at their site's Domain Controller as the primary DNS server, and a DNS server at a different site as the secondary DNS server. For simplicity's sake, we can say that the secondary server would be the Domain Controller at the home site for everyone, and there are no tertiary DNS servers (even though that's not actually the case). Try as I might, I can't seem to find a GPO setting for this (at least on FL 2003 R2, the Computer Configuration - Administrative Templates - Network - DNS Client - DNS Servers GPO is Supported on: Windows XP Professional only), and I find it rather hard to believe that the "best"/"standard" solution would therefore be either scripting up something to apply the DNS settings per site, or using a DHCP server to push those configurations out to the other servers via the DHCP Scope Options. So, is there a standard way of managing this configuration? (That's hopefully not "a script" or "DHCP Scope Option.)

  Read the article

• Unable to ssh to a Linux VM after a day

  - by jogabonito

  I have a machine running 4 VMs on it. There is one Fedora VM which is causing me some trouble. The IPs of the VMs are something like 10.100.100.* I have a Windows PC which is in the same network. It has an IP 10.100.25.77. When I reboot the Fedora VM, I am able to ping it from my Windows PC as well as use putty to ssh to it. The next day, I cant ping it or ssh from my Windows PC. However I can ping and ssh to the other VMs on the machine. If I ssh to one of the other VMs, I can ping and ssh to the Fedora VM. Next if I restart it, things get back to normal and I can access it without any issues. The IP of the VM doesn't change after rebooting and it is statically assigned I would like to know what is causing this and how to get it fixed. As a last resort, I am thinking of running a cron job to restart the VM every night, it is not a critical server, but will be generally used occasionally in the day time.

  Read the article

< Previous Page | 173 174 175 176 177 178 179 180 181 182 183 184  | Next Page >