Search Results

Search found 8344 results on 334 pages for 'count'.

Page 200/334 | < Previous Page | 196 197 198 199 200 201 202 203 204 205 206 207  | Next Page >

• Hard Disk DRDY error: is it a crash

  - by pranjal

  I am using IBM Thinkpad, 1.7GHz, 512 RAM with Linux Mint 9 installed. I have two partitions in addition to root. One of the partitions became read-only yesterday, after which I rebooted my system. It is extremely slow along with DRDY Error : Is my Hard disk crashed ? Error Log while booting. Differences between boot sector and its backup. failed command : READ DMA BMDMA : stat 0X25 ata 1.00 : status : { DRDY ERR } ata 1.00 : status :{ UNC } Buffer I/O error on logical device, logical block 65467 smartctl output for the partition: mint mint # smartctl -a /dev/sda1 smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: TOSHIBA MK4026GAX RoHS Serial Number: X5LY1623T Firmware Version: PA107E User Capacity: 40,007,761,920 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 6 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Thu Feb 17 06:48:25 2011 UTC SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x84) Offline data collection activity was suspended by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 153) seconds. Offline data collection capabilities: (0x1b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. No Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. No General Purpose Logging support. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 30) minutes. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0 3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 310 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 3968 5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 40 7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0 9 Power_On_Hours 0x0032 082 082 000 Old_age Always - 7257 10 Spin_Retry_Count 0x0033 179 100 030 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3484 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 489 193 Load_Cycle_Count 0x0032 064 064 000 Old_age Always - 367150 194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 36 (Lifetime Min/Max 14/57) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 33 197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 82 198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 1 199 UDMA_CRC_Error_Count 0x0032 200 253 000 Old_age Always - 0 220 Disk_Shift 0x0002 100 100 000 Old_age Always - 101 222 Loaded_Hours 0x0032 085 085 000 Old_age Always - 6146 223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0 224 Load_Friction 0x0022 100 100 000 Old_age Always - 0 226 Load-in_Time 0x0026 100 100 000 Old_age Always - 227 240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0 SMART Error Log Version: 1 ATA Error Count: 2371 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2371 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:03:10.061 READ DMA f8 00 00 00 00 00 e0 00 00:03:10.061 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:03:10.053 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:03:10.053 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:03:10.053 READ NATIVE MAX ADDRESS Error 2370 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:03:03.328 READ DMA f8 00 00 00 00 00 e0 00 00:03:03.327 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:03:03.320 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:03:03.319 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:03:03.319 READ NATIVE MAX ADDRESS Error 2369 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:02:56.582 READ DMA f8 00 00 00 00 00 e0 00 00:02:56.582 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:02:56.574 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:02:56.574 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:02:56.574 READ NATIVE MAX ADDRESS Error 2368 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:02:49.809 READ DMA f8 00 00 00 00 00 e0 00 00:02:49.809 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:02:49.801 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:02:49.801 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:02:49.801 READ NATIVE MAX ADDRESS Error 2367 occurred at disk power-on lifetime: 7256 hours (302 days + 8 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 05 1a 1b 00 e0 Error: UNC 5 sectors at LBA = 0x00001b1a = 6938 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 05 1a 1b 00 e0 00 00:02:43.056 READ DMA f8 00 00 00 00 00 e0 00 00:02:43.056 READ NATIVE MAX ADDRESS ec 00 00 00 00 00 a0 02 00:02:43.048 IDENTIFY DEVICE ef 03 45 00 00 00 a0 02 00:02:43.048 SET FEATURES [Set transfer mode] f8 00 00 00 00 00 e0 00 00:02:43.047 READ NATIVE MAX ADDRESS SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] Device does not support Selective Self Tests/Logging Do I need to get a new Hard Disk my PC ?

  Read the article

• UISegmentedControl tint color on touch

  - by gotye

  Hey everyone, I have a UISegmentedControl in my app (see code below) : // --------------- SETTING NAVIGATION BAR RIGHT BUTTONS NSArray *segControlItems = [NSArray arrayWithObjects:[UIImage imageNamed:@"up.png"],[UIImage imageNamed:@"down.png"], nil]; segControl = [[UISegmentedControl alloc] initWithItems:segControlItems]; segControl.segmentedControlStyle = UISegmentedControlStyleBar; segControl.momentary = YES; segControl.frame = CGRectMake(25.0, 7, 65.0, 30.0); segControl.tintColor = [UIColor blackColor]; [segControl addTarget:self action:@selector(segAction:) forControlEvents:UIControlEventValueChanged]; if (current == 0) [segControl setEnabled:NO forSegmentAtIndex:0]; if (current == ([news count]-1)) [segControl setEnabled:NO forSegmentAtIndex:1]; // --------------- But I can't make it to show something when you click on it ... It functionnally works perfectly but I would like it to tint to gray when you click on it (but just when you click) ... would that be possible ? Thank you, Gotye.

  Read the article

• R strsplit and vectorization

  - by James

  When creating functions that use strsplit, vector inputs do not behave as desired, and sapply needs to be used. This is due to the list output that strsplit produces. Is there a way to vectorize the process - that is, the function produces the correct element in the list for each of the elements of the input? For example, to count the lengths of words in a character vector: words <- c("a","quick","brown","fox") > length(strsplit(words,"")) [1] 4 # The number of words (length of the list) > length(strsplit(words,"")[[1]]) [1] 1 # The length of the first word only > sapply(words,function (x) length(strsplit(x,"")[[1]])) a quick brown fox 1 5 5 3 # Success, but potentially very slow Ideally, something like length(strsplit(words,"")[[.]]) where . is interpreted as the being the relevant part of the input vector.

  Read the article

• Ignoring old multiple asynchronous ajax requests

  - by Travis

  I've got a custom javascript autocomplete script that hits the server with multiple asynchronous ajax requests. (Everytime a key gets pressed.) I've noticed that sometimes an earlier ajax request will be returned after a later requests, which messes things up. The way I handle this now is I have a counter that increments for each ajax request. Requests that come back with a lower count get ignored. I'm wondering: Is this proper? Or is there a better way of dealing with this issue? Thanks in advance, Travis

  Read the article

• C# WPF application is using too much memory while GC.GetTotalMemory() is low

  - by Dmitry

  I wrote little WPF application with 2 threads - main thread is GUI thread and another thread is worker. App has one WPF form with some controls. There is a button, allowing to select directory. After selecting directory, application scans for .jpg files in that directory and checks if their thumbnails are in hashtable. if they are, it does nothing. else it's adding their full filenames to queue for worker. Worker is taking filenames from this queue, loading JPEG images (using WPF's JpegBitmapDecoder and BitmapFrame), making thumbnails of them (using WPF's TransformedBitmap) and adding them to hashtable. Everything works fine, except memory consumption by this application when making thumbnails for big images (like 5000x5000 pixels). I've added textboxes on my form to show memory consumption (GC.GetTotalMemory() and Process.GetCurrentProcess().PrivateMemorySize64) and was very surprised, cuz GC.GetTotalMemory() stays close to 1-2 Mbytes, while private memory size constantly grows, especially when loading new image (~ +100Mb per image). Even after loading all images, making thumbnails of them and freeing original images, private memory size stays at ~700-800Mbytes. My VirtualBox is limited to 512Mb of physical memory and Windows in VirtualBox starts to swap alot to handle this huge memory consumption. I guess I'm doing something wrong, but I don't know how to investigate this problem, cuz according to GC, allocated memory size is very low. Attaching code of thumbnail loader class: class ThumbnailLoader { Hashtable thumbnails; Queue<string> taskqueue; EventWaitHandle wh; Thread[] workers; bool stop; object locker; int width, height, processed, added; public ThumbnailLoader() { int workercount,i; wh = new AutoResetEvent(false); thumbnails = new Hashtable(); taskqueue = new Queue<string>(); stop = false; locker = new object(); width = height = 64; processed = added = 0; workercount = Environment.ProcessorCount; workers=new Thread[workercount]; for (i = 0; i < workercount; i++) { workers[i] = new Thread(Worker); workers[i].IsBackground = true; workers[i].Priority = ThreadPriority.Highest; workers[i].Start(); } } public void SetThumbnailSize(int twidth, int theight) { width = twidth; height = theight; if (thumbnails.Count!=0) AddTask("#resethash"); } public void GetProgress(out int Added, out int Processed) { Added = added; Processed = processed; } private void AddTask(string filename) { lock(locker) { taskqueue.Enqueue(filename); wh.Set(); added++; } } private string NextTask() { lock(locker) { if (taskqueue.Count == 0) return null; else { processed++; return taskqueue.Dequeue(); } } } public static string FileNameToHash(string s) { return FormsAuthentication.HashPasswordForStoringInConfigFile(s, "MD5"); } public bool GetThumbnail(string filename,out BitmapFrame thumbnail) { string hash; hash = FileNameToHash(filename); if (thumbnails.ContainsKey(hash)) { thumbnail=(BitmapFrame)thumbnails[hash]; return true; } AddTask(filename); thumbnail = null; return false; } private BitmapFrame LoadThumbnail(string filename) { FileStream fs; JpegBitmapDecoder bd; BitmapFrame oldbf, bf; TransformedBitmap tb; double scale, dx, dy; fs = new FileStream(filename, FileMode.Open); bd = new JpegBitmapDecoder(fs, BitmapCreateOptions.None, BitmapCacheOption.OnLoad); oldbf = bd.Frames[0]; dx = (double)oldbf.Width / width; dy = (double)oldbf.Height / height; if (dx > dy) scale = 1 / dx; else scale = 1 / dy; tb = new TransformedBitmap(oldbf, new ScaleTransform(scale, scale)); bf = BitmapFrame.Create(tb); fs.Close(); oldbf = null; bd = null; GC.Collect(); return bf; } public void Dispose() { lock(locker) { stop = true; } AddTask(null); foreach (Thread worker in workers) { worker.Join(); } wh.Close(); } private void Worker() { string curtask,hash; while (!stop) { curtask = NextTask(); if (curtask == null) wh.WaitOne(); else { if (curtask == "#resethash") thumbnails.Clear(); else { hash = FileNameToHash(curtask); try { thumbnails[hash] = LoadThumbnail(curtask); } catch { thumbnails[hash] = null; } } } } } }

  Read the article

• Creating an Excel 2007 bubble chart with date values in axis

  - by Shadowfoot

  I'm trying to create a graph showing the duration of issue resolution. I believe a bubble chart in excel will show what I want but I can't manage to get it working correctly. For each date I have a number of days (duration) and a number of issues (magnitude). Most dates have a duration of 1 with a large magnitude, and I want to avoid the outliers dominating the chart. e.g. 1-Feb, 1, 15 1-Feb, 2, 10 1-Feb, 9, 1 2-Feb, 1, 11 2-Feb, 2, 14 2-Feb, 6, 2 2-Feb, 18, 1 etc. I want the data in this example to give me 2 columns of bubbles. When I try to get excel to create the chart I can't get the date to appear at on the x axis; I get a count (representing the row of the data) instead, and as each row is a separate column, the values don't line up for the date. Can this be done in Excel 2007 without using VBA?

  Read the article

• xCode "Property access results unused - getters should not be used for side effects"

  - by David DelMonte

  Hi all, I'm getting this warning when I'm calling a local routine. My code is this: -(void)nextLetter { // NSLog(@"%s", __FUNCTION__); currentLetter ++; if(currentLetter > (letters.count - 1)) { currentLetter = 0; } self.fetchLetter; } I'm getting the warning on the self.fetchLetter statement. That routine looks like this: - (void)fetchLetter { // NSLog(@"%s", __FUNCTION__); NSString *wantedLetter = [[letters objectAtIndex: currentLetter] objectForKey: @"langLetter"]; NSString *wantedUpperCase = [[letters objectAtIndex: currentLetter] objectForKey: @"upperCase"]; ..... } I prefer to fix warning messages, is there a better way to write this? Thanks!

  Read the article

• Atomic INSERT/SELECT in HSQLDB

  - by PartlyCloudy

  Hello, I have the following hsqldb table, in which I map UUIDs to auto incremented IDs: SHORT_ID (BIG INT, PK, auto incremented) | UUID (VARCHAR, unique) Create command: CREATE TABLE table (SHORT_ID BIGINT GENERATED BY DEFAULT AS IDENTITY PRIMARY KEY, UUID VARCHAR(36) UNIQUE) In order to add new pairs concurrently, I want to use the atomic MERGE INTO statement. So my (prepared) statement looks like this: MERGE INTO table USING (VALUES(CAST(? AS VARCHAR(36)))) AS v(x) ON ID_MAP.UUID = v.x WHEN NOT MATCHED THEN INSERT VALUES v.x When I execute the statement (setting the placeholder correctly), I always get a Caused by: org.hsqldb.HsqlException: row column count mismatch Could you please give me a hint, what is going wrong here? Thanks in advance.

  Read the article

• retreive POST data from FLASH to ASP.Net

  - by Martin Ongtangco

  here's my AS3 code: var jpgEncoder:JPGEncoder = new JPGEncoder(100); var jpgStream:ByteArray = jpgEncoder.encode(bitmapData); var header:URLRequestHeader = new URLRequestHeader("Content-type", "application/octet-stream"); var jpgURLRequest:URLRequest = new URLRequest("/patients/webcam.aspx"); jpgURLRequest.requestHeaders.push(header); jpgURLRequest.method = URLRequestMethod.POST; jpgURLRequest.data = jpgStream; navigateToURL(jpgURLRequest, "_self"); And here's my ASP.Net Code try { string pt = Path.Combine(PathFolder, "test.jpg"); HttpFileCollection fileCol = Request.Files; Response.Write(fileCol.Count.ToString()); foreach (HttpPostedFile hpf in fileCol) { hpf.SaveAs(pt); } } catch (Exception ex) { Response.Write(ex.Message); } im getting a weird error, HttpFox mentioned: "NS_ERROR_NET_RESET" Any help would be excellent! Thanks!

  Read the article

• C# yield return not returning an item as expected

  - by Jiho Han

  I have following code: private void ProcessQueue() { foreach (MessageQueueItem item in GetNextQueuedItem()) PerformAction(item); } private IEnumerable<MessageQueueItem> GetNextQueuedItem() { if (_messageQueue.Count > 0) yield return _messageQueue.Dequeue(); } Initially there is one item in the queue as ProcessQueue is called. During PerformAction, I would add more items to _messageQueue. However, the foreach loop quits after the initial item and does not see the subsequent items added. I sense that somehow the initial state of the queue is being captured by yield. Can someone explain what is happening and give a solution?

  Read the article

• Net::Cassandra::Easy equivalent of "SELECT * FROM ..."

  - by knorv

  When using Perl's Net::Cassandra::Easy the following code will retrieve columns col[1-3] from rows row[1-3]: $result = $cassandra->get(['row1', 'row2', 'row3'], family => 'Standard1', byname => ['col1', 'col2', 'col3'); The corresponding SQL would be: SELECT col1, col2, col3 FROM rows WHERE id IN ('row1', 'row2', 'row3'); Suppose instead that I want to retrieve all columns. In SQL terms that would be: SELECT * FROM rows WHERE id IN ('row1', 'row2', 'row3'); To get all columns I am currently using: $result = $cassandra->get(['row1', 'row2', 'row3'], family => 'Standard1', byoffset => { "count" => 1_000_000 }); This works as long as the number of columns does not exceed one million. While this works I'd assume that there is a cleaner way to do it. My question is: Is there any cleaner way to specify to Cassandra that I want to retrieve all columns for the maching rows?

  Read the article

• netlogo programming question - catalyst implementation part 2

  - by user286190

  hi the catalyst speeds up the reaction but remains unchanged after the reaction has taken place i tried the following code breed [catalysts catalyst] breed [chemical-x chemical-x] ;then the forward reaction is sped up by the existence of catalysts to react-forward let num-catalysts count catalysts ;speed up by num-catalysts ;... end and it works fine but I want to make it so that the catalyst can be switched on and off with the 'switch' button ..so one can see the effects with and without the catalyst..i tried putting a switch in but catalyst has already been defined Also i want to make the catalyst visible so one can see it in the actual implementation (in the world) like making it a turtle is there are another way to implement this apart from using breeds i tried making the catalyst a turtle but it doesnt work ; Make catalyst visible in implementation clear-all crt catalysts 100 ask catalysts [ set color white ] show [breed] of one-of catalysts ; prints catalysts any help will be greatly appreciated thank you

  Read the article

• c# gridview row click

  - by Martijn

  When i click on a row in my gridview, i want to go to a other page with the id i get from the database. In my RowCreated event i have the following line: e.Row.Attributes.Add("onClick", ClientScript.GetPostBackClientHyperlink(this.grdSearchResults, "Select$" + e.Row.RowIndex)); To prevent error messages i have this code: protected override void Render(HtmlTextWriter writer) { // .NET will refuse to accept "unknown" postbacks for security reasons. Because of this we have to register all possible callbacks // This must be done in Render, hence the override for (int i = 0; i < grdSearchResults.Rows.Count; i++) { Page.ClientScript.RegisterForEventValidation(new System.Web.UI.PostBackOptions(grdSearchResults, "Select$" + i.ToString())); } // Do the standard rendering stuff base.Render(writer); } My question is, how can i give a row a unique id (from the DB) and when i click the row, another page is opened (like clicking on a href) and that page can read the id. Thnx

  Read the article

• Alternative Input Device(Midi) doesn't prevent Screen Saver in Winforms application

  - by DTig

  I have developed a c# winforms application whereby the user is providing input via a midi connected device. The user will go for long periods without using the keyboard or mouse. When I receive a midi message is there anything I can do to "tell" the system that this counts as user activity (ie key press). I don't want the screen saver or time lockouts to occur, if they are actively using the midi device. I think my request is different than other requests I've seen because they want to disable screen savers for the life of their application whereby I just want midi input I receive to count as user interactivity. Is there something I can call when I receive midi input to signify to the system user activity?

  Read the article

• will_paginate undefined method error - Ruby on Rails

  - by bgadoci

  I just installed the gem for will_paginate and it says that it was installed successfully. I followed all the instructions listed with the plugin and I am getting an 'undefined method `paginate' for' error. Can't find much in the way of Google search and haven't been able to fix it myself (obviously). Here is the code: PostsController def index @tag_counts = Tag.count(:group => :tag_name, :order => 'updated_at DESC', :limit => 10) @posts = Post.paginate :page => params[:page], :per_page => 50 respond_to do |format| format.html # index.html.erb format.xml { render :xml => @posts } format.json { render :json => @posts } format.atom end end /model/post.rb class Post < ActiveRecord::Base validates_presence_of :body, :title has_many :comments, :dependent => :destroy has_many :tags, :dependent => :destroy cattr_reader :per_page @@per_page = 10 end /posts/views/index.html.erb <%= will_paginate @posts %>

  Read the article

• how callback a function on 404 on JSON ajax request with Jquery?

  - by shingara

  I want made an Ajax request with response on JSON. So I made this Ajax request : $.ajax({ url: 'http://my_url', dataType: "json", success: function(data){ alert('success'); }, error: function(data){ alert('error'); }, complete: function(data) { alert('complete') }}) This code works good but when my url send me a HTTP code 404, no callbacks are used, even the complete callback. After research, it's because my dataType is 'json' so 404 return is HTML and the JSON parsing failed. So no callback. Have you a solution to call a callback function when a 404 is raised ? EDIT: complete callback don't call is return is 404. If you want an URL wit 404 you can call : http://twitter.com/status/user_timeline/jksqdlmjmsd.json?count=3&callback=jsonp1269278524295&_=1269278536697 it's with this URL I have my problem.

  Read the article

• jquery validate plugin: add a custom method

  - by pixeline

  I need some guidance on how to add a validation method to the jquery validate plugin. I've gathered that i need to use the plugin's addMethod() function, but how exactly to have it do what i need... Here i am! My form 's first question is a radio input choice. Each radio input, if selected, shows a sub-question of several checkboxes. What i would like my validation to do is: - make sure one radio input is selected - make sure at least one checkbox pertaining to the radio input is selected. Basically, out of the validate plugin's own logic, i would count the selector's length, and if there isn't any, return the error message. Something like this: var weekSelected = ($('input.seasonSelector:checked input.weekSelector:checked',form).length > 0); if(!weekSelected){ return 'Please select a week inside that season'; } How to turn that into a validate plugin method ?

  Read the article

• Session state in asp.net mvc

  - by tiff

  I would like to know how to use session state in a simple log in log out in asp.net mvc.. I have a code here in my controller that I've retrieved from my mysql database for my session log in..but I don't really know how to manipulate it.. <AcceptVerbs(HttpVerbs.Post)> _ Function Index(ByVal username As String, ByVal password As String, ByVal department As String) As ActionResult Dim user As DataTable user = Account.userSelect(username:=username, password:=password, department:=department) If user.Rows.Count = 0 Then Return RedirectToAction("Index", "Home") Else Session("username") = user.Rows(0).Item("username") Session("department") = user.Rows(0).Item("department") Return RedirectToAction("News", "Administration") End If End Function Thank you!

  Read the article

• How to use jQuery .each() - I get a value, but it's the wrong one

  - by Ankur

  I am returning a JSON object (as a String) through a servlet. The JSON object looks like this: {"3":"Martin Luther","30":"Boris Becker","32":"Joseph Goebels","19":"Leonardo Da Vinci","31":"Adolf Hitler"} My jQuery looks like this (the submission of data is correct because I get a proper looking result from the servlet): $.ajax( { type : "GET", url : "MyServlet", data : queryString + "count=" + variables, success : function(resultObj) { $.each(resultObj, function(key, value) { $("#resultCount").html(key+", "+value); }); } }); However when I try to print the results, that is the variables key and value, I get a number for the key but not a number from the JSONObject and an empty string instead of the value. Essentially the question is about how to "extract" the information from a JSON object.

  Read the article

• How to optimize this MySQL query

  - by James Simpson

  This query was working fine when the database was small, but now that there are millions of rows in the database, I am realizing I should have looked at optimizing this earlier. It is looking at over 600,000 rows and is Using where; Using temporary; Using filesort (which leads to an execution time of 5-10 seconds). It is using an index on the field 'battle_type.' SELECT username, SUM( outcome ) AS wins, COUNT( * ) - SUM( outcome ) AS losses FROM tblBattleHistory WHERE battle_type = '0' && outcome < '2' GROUP BY username ORDER BY wins DESC , losses ASC , username ASC LIMIT 0 , 50

  Read the article

• What is a Perl regex for finding the first non-consecutively-repeating character in a string.

  - by DVK

  Your task, should you choose to accept it, is to write a Perl regular expression that for a given string, will return the first occurence of a character that is not consecutively duplicated. In other words, both preceded AND succeeded by characters different from itself (or start/end of string respectively). Example: IN: aabbcdecc OUT: c Please note that "not consecutively duplicated" does not mean "anywhere in the string". NOTE: it must be a pure regex expression. E.g. the solution that obviously comes to mind (clone the string, delete all the duplicates, and print the first remaining character) does not count, although it solves the problem. The question is inspired by my somewhat off-topic answer to this: http://stackoverflow.com/questions/2548606/perl-function-to-find-first-non-repeating-character-in-a-string

  Read the article

• Cassandra/HBase or just MySQL: Potential problems doing the next thing

  - by alexeypro

  Say I have "user". It's the key. And I need to keep "user count". I am planning to have record with key "user" and value "0" to "9999+ ;-)" (as many as I'll have). What problems I will drive in if I use Cassandra, HBase or MySQL for that? Say, I have thousand of new updates to this "user" key, where I need to increment the value. Am I in trouble? Locked for writes? Any other way of doing that? Why this is done -- there will be a lot of "user"-like keys. Different other cases. But the idea is the same. Why keep it this way -- because I'll have more reads, so I can always get "counted value" very fast.

  Read the article

• Combinatorics, probability, dice

  - by TarGz

  A friend of mine asked: if I have two dice and I throw both of them, what is the most frequent sum (of the two dice' numbers)? I wrote a small script: from random import randrange d = dict((i, 0) for i in range(2, 13)) for i in xrange(100000): d[randrange(1, 7) + randrange(1, 7)] += 1 print d Which prints: 2: 2770, 3: 5547, 4: 8379, 5: 10972, 6: 13911, 7: 16610, 8: 14010, 9: 11138, 10: 8372, 11: 5545, 12: 2746 The question I have, why is 11 more frequent than 12? In both cases there is only one way (or two, if you count reverse too) how to get such sum (5 + 6, 6 + 6), so I expected the same probability..?

  Read the article

• regex matches with intersection in C#

  - by StuffHappens

  Hello. I wonder if it is possible to get MatchCollection with all matches even if there's intersection among them. string input = "a a a"; Regex regex = new Regex("a a"); MatchCollection matches = regex.Matches(input); Console.WriteLine(matches.Count); This code return 1, but I want it to return 2. How do achive it? Thank you for your help.

  Read the article

• Saving Multiple Annotations -NSUserDefaults

  - by casillas

  I came cross this code as shown below.In the following code, I could able to save only one single annotation, however I have an array of annotations, I could not able to save them with single NSUserDefaults To save: NSUserDefaults *ud = [NSUserDefaults standardUserDefaults]; [ud setDouble:location.latitude forKey:@"savedCoordinate-latitude"]; [ud setDouble:location.longitude forKey:@"savedCoordinate-longitude"]; [ud setBool:YES forKey:@"savedCoordinate-exists"]; [ud synchronize]; Edited: -(void)viewDidLoad NSUserDefaults *ud=[NSUserDefaults standardUserDefaults]; if([ud boolForKey:@"save-exist"]) { NSMutableArray *udAnnotations=[[NSMutableArray alloc]initWithArray: [ud objectForKey:@"annotationsArray"]]; NSLog(@"%d",[udAnnotations count]); } else{ [self addAnno]; } -(void)addAnno { [mapView addAnnotations:annotationArray]; NSUserDefaults *ud=[NSUserDefaults standardUserDefaults]; [ud setObject:annotationArray forKey:@"annotationsArray"]; [ud setBool:YES forKey:@"save-exist"]; [ud synchronize]; }

  Read the article

< Previous Page | 196 197 198 199 200 201 202 203 204 205 206 207  | Next Page >