Search Results

Search found 9235 results on 370 pages for 'social networking'.

Page 205/370 | < Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >

• Mac | Router not assigning the IP address.

  - by Vaibhav Bajpai

  I recently installed Mac OS X 10.6, however the ethernet state is down. The assigned IP is 169.x.x.x. When booted the live USB of Ubuntu, I properly get an IP assigned in the range 192.168.1.x from the router 192.168.1.1 I am using the same router and same ethernet line. I tried to ping to 192.168.1.1 from my Mac and I get a host down message. I tried to manually assign the IP and set the router IP to 192.168.1.1 but still the router is unreachable.

  Read the article

• Sharing files between multiple computers?

  - by Koalatea

  At my school, we have 13 iMacs that we use to make our yearbook. Currently our school has some servers for us, but since we work with so many files ( thousands of pictures, most of which are ~3MB ) it slows down far too much. Is there a way to better share files between our computers? We are on a wireless network and the whole school shares the same servers, we have around probably 400 computers in the school. Is there a hardware fix I can do? Something like buying an external and hooking only yearbook computers to it?

  Read the article

• LMDE detects a wireless card, but can't use it

  - by Davidos

  LMDE can see my wireless card, and correctly identifies it, but it refuses to let me turn it on through the shiny graphical interface. Is there a way to use the non-shiny terminal to turn on my wireless? One small tidbit I noticed was the stated version; it says the version is 00. I believe that's hexadecimal for 0, which may indicate something screwy with the software. It would be nice if someone could tell me how to figure out how to solve this kind of problem in the future. *-network DISABLED description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:09:00.0 logical name: wlan0 version: 00 serial: 91:e3:7b:0d:a3:a9 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-1-amd64 firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:43 memory:e1d00000-e1d01fff I've tested multiple other network managers, and none of them work. W ireless switch is on, I'm sure it's a driver problem.

  Read the article

• Keeping the wireless connected.

  - by casr

  I’m running OpenBSD on a computer which is connected via wireless to the network. It is a well supported NIC and I’ve had no problems with it from a hardware perspective. Unfortunately my wireless access point occasionally loves to forget it’s settings. I then have to help it remember. However, in this intervening time my OpenBSD box drops the connection and then does not automatically reconnect. I have alleviated my problems by running this simple script in the background: #!/bin/sh while [ 1 ] do ping -c1 192.168.1.254 > /dev/null if [ $? = 1 ] then sh /etc/netstart ral0 > /dev/null fi sleep 30 done [Ping the access point. If there is no response attempt to reconnect.] It seems to me to be a very suboptimal solution. Has anyone else come across a better way?

  Read the article

• SQL ERROR: Verify that the instance name is correct and that SQL Server is configured to allow remote connections?

  - by scepak

  I am getting following error while connecting to my local Sql Express. An error has occurred. Details of the exception: A network-related or instance-specific error occurred while establishing a conne ction to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Serve r/Instance Specified) Unable to connect to SQL Server database. I am able to connect to Sql Server using Management Studio.

  Read the article

• Open a remote folder in windows mobile

  - by Luis

  I have a device with windows mobile 6.1 and I want to open a shared folder on my laptop with the file browser... Both are connected to the same wireless network, both have access to internet but I can't have access between them... I have used open path in the file explorer and nothing... I shut down the firewall on mi laptop but still I can't access.. I don't know anything about permissions if that is the problema because I'm a novice... if anyone can helpme I'll appreciate it a lot...Thanks...

  Read the article

• Access server by hostname without domain

  - by projectshave

  I want to access services on other machines on my home network with just their hostname. In every browser, "http://machine" fails, but adding a period in "http://machine./" works. Is there a way to avoid adding that extra period? My setup is a router with DD-WRT w/ DNSmasq turned on, Win7 machines and several Ubuntu VMs. nslookup works fine with just hostname. Remote desktop works, but TightVNC needs the extra period. ssh needs the period. As I said, all my browsers need the extra period. I'd prefer a solution that doesn't require manually maintaining the hosts file. Thanks.

  Read the article

• How can I determine the IP addresses allocated by DHCP on a router that I'm connected to?

  - by user234831

  This "router" is not a typical situation. I'm using my phone as a hotspot and can only configure a select number of DHCP options. I can manage the limit on how many devices/clients can use my phone as a hotspot. I have to select from a radio-button list with the options: 2,3,4,5, or 8 I can specify the DHCP starting IP address. In this case, it begins at 192.168.6.106 When I'm connected via WIFI to my phone, an ipconfig /all command shows me that the default gateway is 192.168.6.1 and my IPv4 address is 192.168.1.148. I have the luxury of connecting another device to the phone and that device was assigned 192.168.1.121. I've tried connecting to 192.168.6.1, hoping for some sort of router setup page that I'm used to seeing, but there is no such thing or maybe it's just a matter of incompatable operating systems. In summary, the "router" (phone) has an IP address of 192.168.6.1 and a DHCP server that begins at 192.168.6.106 and allows up to 8 connections. Normally, I would assume a range of 192.168.6.106 - 192.168.6.113, but connected clients are showing otherwise. How can I figure out which IP addresses are set aside by DHCP for clients?

  Read the article

• Would a switch be covered by a router's firewall

  - by Uh-yeah...

  So... Hopefully; this is the right place for this question. I need more Ethernet ports on my home network. Sadly, we already have an old router connected to the main router and we still need more ports. I feel dumb for asking; but, I just would like to double check. Would the devices connected to the switch be "protected" by the Main router's firewall? ? Up to this point I have assumed that was the case; but, a co-worker is convinced that is not the case [ I believe he is thinking of a situation in which the switch (un-managed) is before an access point]. [It would go modem to main router; main router then has the switch and old router connected to it.

  Read the article

• Service redirection on same network

  - by Unode

  I have a network on which I run multiple servers each dedicated to a given service. Because most services run on distinct ports I'm currently looking for a way of unifying "all" services into a single "proxy" machine. The idea is to abstract which machine is being accessed but still allow direct connection if needed/requested. This "proxy" machine has only one network interface which is part of the same network as all the other service providing machines. I've looked into Routing and NAT but I've so far failed to figure out how to make it work. I tried to achieve this using shorewall but couldn't find clear examples. However I'm not entirely sure this is the best/simplest strategy. With that said, what would be the best way of achieving this result? Example case: Proxy IP - Listening port - Send requests to 192.168.0.50 80 192.168.0.1:80 " 22 192.168.0.2:2222 " 3306 192.168.0.3:3000 " 5432 192.168.0.4:5432 " 5222 192.168.0.5:5222 PS: I'm not concerned with the single-point-of-failure nature of the proxy. Thanks

  Read the article

• Remote Desktop connection breaks the wireless connection

  - by Michal Talaga

  When I connect to my Windows 8 Professional machine via Remote Desktop (RDP) I almost always get my WiFi connection broken. The setup: T61P Lenovo Laptop + W8 at home Wireless Router with NAT forwards connections to that machine Windows 7 laptop at work connecting to the home laptop When I connect, very often I get to login and suddenly connection is lost and I cannot reconnect again. When I get home I find my WiFi connection is still connected to the Access Point but does not function. Can't even ping the router. What is strange is that disabling wireless with the hardware switch and enabling it again doesn't help. The only way to make it works again: - Reboot - Disable wifi with hardware switch AND disable the network card in Device Manager, then enable both I did not have this problem on the very same laptop when it was running Windows 7. Any hint how can I find where the problem is?

  Read the article

• Route outbound connections from local network through VPN

  - by Sharkos

  I have a server A running OpenVPN, an OpenVPN client B (a rooted Android phone as it happens) and a third party C (a laptop, tablet etc.) tethered to B. B can use the VPN to access the internet via A; C can use the tethered connection WITHOUT the VPN to access the internet via B. However, with the VPN on B active, I cannot load information from the internet on C. A appears to log similar traffic inbound and outbound when B or C attempt to load a webpage, say, but the VPN on device B reports no inbound traffic when the connection originated from C. Where should I look for packets being dropped, and what ip rules should I use to make sure they are passed back through the VPN and into the local network B <- C? (I'll obviously post whatever further information is needed.) Further info Without VPN: root@android:/ # ip route default via [B's External Gateway] dev rmnet0 [B's External Subnet] dev rmnet0 proto kernel scope link src [B's External IP] [B's External Gateway] dev rmnet0 scope link 192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.1 With VPN: root@android:/ # ip route 0.0.0.0/1 dev tun0 scope link default via [B's External Gateway] dev rmnet0 [B's External Subnet] dev rmnet0 proto kernel scope link src [B's External IP] [B's External Gateway] dev rmnet0 scope link [External address of A] dev tun0 scope link 128.0.0.0/1 dev tun0 scope link 172.16.0.0/24 dev tun0 scope link 172.16.0.8/30 dev tun0 proto kernel scope link src 172.16.0.10 192.168.43.0/24 dev wlan0 proto kernel scope link src 192.168.43.1 192.168.168.0/24 dev tun0 scope link

  Read the article

• Disable Network settings (TCP/IP & DNS) on Windows 7 Ultimate

  - by TiD91

  i also read this discussion here How to disable Tcp/Ip settings in windows 7 via GPO? about what i want to do but i still have problems. So here i am: i have a desktop pc with two accounts, both with Administrative rights. One is used by the entire my family, in particular by my brother. The problem is that i set some DNS and IP configurations to let be possible the VNC connection from remote. Now i would like to disable the network settings (TCP/IP and DNS) to prohibit my brother to change it preventing me to connect to it. So how can i do this? I set the policies from GPO but i still can change these settings from his account. Here's a pic of Registry Keys: http://imageshack.us/a/img339/3310/famigliapc2012092017274.png what didn't i do? Thanks in advance for your help. Rub|TiD

  Read the article

• Windows 7 - saved wifi access points disappear from list

  - by KáGé

  I'm having a weird issue with Windows 7 x64: I'm moving my notebook between two locations weekly, at each I have a wifi router. They both have hidden SSID-s, which are different. If I save one, the other one gets deleted from the list, as if overwritten, so I always have to retype the SSID and password, if I want to connect after moving my computer. At first I tought the problem was caused by both routers having the same password, but after I changed one (suffixed it with "_2") it persisted. What can I do about this? Thanks.

  Read the article

• setting up static ip on linux

  - by user64908

  I understood the interface file in linux needs to be edited and the corresponding lines added. I don't understand what network and broadcast are for, it seems extra versus a windows static ip configuration. In my case my gateway is 192.168.5.1 and my machine ip is 192.168.5.101, what would be my network and broadcast address, is the below correct and what exactly do they mean? iface eth0 inet static address 192.168.5.101 gateway 192.168.5.1 netmask 255.255.255.0 network 192.168.5.0 broadcast 192.168.5.255

  Read the article

• Sharing wifi connection

  - by andser

  I have some little problem while sharing wifi connection. I have 2 laptops. I need connection scheme like this: laptop1 [wlan0] >>>>>>>> laptop2 [wlan0] (in ad-hoc mode, as ap, etc) >>>>> laptop2 [wlan1] >>>> internet. laptop1 [wlan0] connecting to laptop2 [wlan0]. laptop2 connecting to internet through wlan1. Is it possible? OS: Ubuntu on both machines I tried this man (setting laptop2 wlan0 in ad-hoc mode): https://help.ubuntu.com/community/WifiDocs/Adhoc#Network_Manager laptop1 connects to laptop2, but can't access to internet.

  Read the article

• Wi-Fi or Bluetooth to USB converter

  - by yerzhik

  Is there a device, that works without a driver, you just connect it as usb, and receive any signal sent to it as if it were COM Port wired connection? For example, such a device that gets data sent to it by Wi-Fi network or Bluetooth and resends it to the USB. Of course it has to be set up once (network name, password etc) and for this purpose you need a driver, but once it is set up, you can use it at any computer without a driver. I have a Bluetooth USB, but I think it can't work without a driver. By just connecting it to any computer you can't find it in device list on another bluetooth device (as phone, etc).

  Read the article

• Stopped windows firewall service during ICS, how is this possible?

  - by insipid

  Although windows firewall is required to be on when you "start" Internet Connection Sharing, you can stop the WF service with MMC. When done a client can still use the host machines internet. The firewall had port 80/http blocked, and now it is open for incoming traffic. However other ports used by applications on the host and client which communicate with each other still seem to be blocked. Can anybody explain what might be happening here? Doesn't ICS need windows firewall for NAT? Note: I am not actually seeing anything in the firewall logs after stopping the service, but even packets sent localhost on the host machine never arriving on these other random ports.

  Read the article

• Use 2 wireless adapters to connect to 2 WIFI networks (local and internet) simultaneously?

  - by Mouad

  On my HP Compaq 6710b there's an internal WIFI network adapter. Attached to the same laptop there's also an external USB Alfa WIFI adapter. I live near campus and can pick it's WIFI signal. The problem is that when I am connected to the Internet Wifi using the internal adapter, and then connect to the home (non-internet) Wifi network's router, I lose the connection to the internet (it stays connected, but there's no actual connection). So how can I use the two adapters to connect to both networks successfully ? The router is Belkin N150 Enhanced Router Model F6D4230-4 V1 The external adapter is: ALFA AWUS 036NHR

  Read the article

• VMWare Player disrupting Samba on Ubuntu 9.04 host?

  - by TonyUser

  I've had Ubuntu 9.04 running on this computer for a while now. I just installed VMWare Player on my system and now when I try to browse the network in the Ubuntu host all the computers will show up one time only. If I try to browse again, no computers appear and even the workgroup is missing. I have to run: sudo /etc/init.d/vmware stop sudo /etc/init.d/samba restart to get the network visable again. As long as VMWare Player is stopped Samba seems fine. I guess it's got to do with the virtual adaptors that VMWare installs. Is there a way to get them both to work, or did I just miss-configure something?

  Read the article

• How to reduce the windows network browsing broadcast timeout or disable this function?

  - by Moi42

  Hello everyone. My residential network is make of 300 vlans (one per room). To browse them we are using a wins server. My problem is that when I try to browse the network, windows first tries to find the neighborhood using some broadcast, and only then does it query the wins server. This "broadcast period" lasts exactly 30 seconds and is very annoying. Can I reduce it, or can I completely disable this broadcast network discovery feature from my system? Thank you for your answers.

  Read the article

• ping preload is not permitted, what could be the reason?

  - by Brogrammer

  I am trying to ping one of my local host and checking CPU process to see how "Ping of death" attack behaves. I tried to ping my other PC which is in local network with 192.168.44.2 IP Address. I tried this, ping -l 5000 192.168.44.2 and I got error like this, ping: -l flag: Operation not permitted I am on MacOSX Lion. How can I remove this flag so machine can let me ping with preload? Thanks for any direction!

  Read the article

• Ubuntu Wired network(ethernet does not work)

  - by user36777

  It was working just fine, until the other day I yanked it out. The wireless works just fine on the same router. If I login to a windows 7 instance on this dual boot laptop then the ehternet works just fine. So it's not a hardware, cable or router issue. The card even gets an ip, but I can't connect to the internet. Here are the details from route, iptables, ifconfig, ping etc. Any ideas? I have been struggling with this for day, none seems to have an answer. http://pastie.org/954816

  Read the article

• Wireless Internet Connection Sharing in Ubuntu

  - by klutch2

  As the title states, I need to share a wireless connection with a laptop running Ubuntu as the AP. The setup will be as follows: Corporate WiFi <<== Laptop <<== Other Devices i.e. (iPad, iPhone) I want to be able to connect the "Other Devices" via WiFi to the laptop. I have thought of setting up an ad-hoc network by connecting to the Corporate WiFi and then setting up a new network and hoping the connection to both would stay, but that doesn't seem to work. If I set up the ad-hoc network by itself, I can see it from my "Other Devices". The reason I need this is because for some reason, my iPad and my iPhone will not connect to my corporate WiFi and I need to use them so I want to use my laptop to share the connection and act as an AP for my "Other Devices". My laptop is a Chrome CR-48 running Ubuntu and as some of you might know, it does not have an ethernet port, so having a wired connecting and then setting up a network is out of question. I want to connect to the Corporate WiFi and share that connection by having the laptop act as an AP for other devices.

  Read the article

• Route gaming data over wireless and everything else through LAN?

  - by Alex

  I have two internet connections available to me. One is via LAN.. not a great ping, but fast downloads. The other is via USB wireless adapter.. good ping, but slow downloads. I want to connect to both of them simultaneously. I want to be able to specify which data or application will use the wireless connection and route everything else through the lan connection. Is this possible, and how would I do it? Windows 7 x64 is my operating system. Here is the data from route print: http://pastebin.com/vsjQRpSM I'm still unsure of how to use this to make all of my data go through the nvidia lan interface, even after reading route /? Also, if I'm able to achieve that, will it override the ForceBindIP?

  Read the article

< Previous Page | 201 202 203 204 205 206 207 208 209 210 211 212  | Next Page >