Search Results

Search found 6972 results on 279 pages for 'usb sata'.

Page 212/279 | < Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >

• Serial port game controller (racing pedals)

  - by Cheesegraterr

  I have an old madCatz racing wheel for the playstation 2. The gas and brake pedals are connected to the wheel by a serial port. I just bought a usb racing wheel for the PC but it lacks pedals so I wanted to see if I could get these old madCatz working. I just installed the serial port in my motherboard, but now I have a problem with software. Nothing will recognize the pedal. I was wondering if there are any programs or drivers out there that will allow me to set the pedals up to work. Any advice would be appreciated!

  Read the article

• Is it possible to shrink the size of an HP Smart Array logical drive?

  - by ewwhite

  I know extension is quite possible using the hpacucli utility, but is there an easy way to reduce the size of an existing logical drive (not array)? The controller is a P410i in a ProLiant DL360 G6 server. I'd like to reduce logicaldrive 1 from 72GB to 40GB. => ctrl all show config detail Smart Array P410i in Slot 0 (Embedded) Bus Interface: PCI Slot: 0 Serial Number: 5001438006FD9A50 Cache Serial Number: PAAVP9VYFB8Y RAID 6 (ADG) Status: Disabled Controller Status: OK Chassis Slot: Hardware Revision: Rev C Firmware Version: 3.66 Rebuild Priority: Medium Expand Priority: Medium Surface Scan Delay: 3 secs Surface Scan Mode: Idle Queue Depth: Automatic Monitor and Performance Delay: 60 min Elevator Sort: Enabled Degraded Performance Optimization: Disabled Inconsistency Repair Policy: Disabled Wait for Cache Room: Disabled Surface Analysis Inconsistency Notification: Disabled Post Prompt Timeout: 15 secs Cache Board Present: True Cache Status: OK Accelerator Ratio: 25% Read / 75% Write Drive Write Cache: Enabled Total Cache Size: 512 MB No-Battery Write Cache: Disabled Cache Backup Power Source: Batteries Battery/Capacitor Count: 1 Battery/Capacitor Status: OK SATA NCQ Supported: True Array: A Interface Type: SAS Unused Space: 412476 MB Status: OK Logical Drive: 1 Size: 72.0 GB Fault Tolerance: RAID 1+0 Heads: 255 Sectors Per Track: 32 Cylinders: 18504 Strip Size: 256 KB Status: OK Array Accelerator: Enabled Unique Identifier: 600508B1001C132E4BBDFAA6DAD13DA3 Disk Name: /dev/cciss/c0d0 Mount Points: /boot 196 MB, / 12.0 GB, /usr 8.0 GB, /var 4.0 GB, /tmp 2.0 GB OS Status: LOCKED Logical Drive Label: AE438D6A5001438006FD9A50BE0A Mirror Group 0: physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 146 GB, OK) physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 146 GB, OK) Mirror Group 1: physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 146 GB, OK) physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 146 GB, OK) SEP (Vendor ID PMCSIERA, Model SRC 8x6G) 250 Device Number: 250 Firmware Version: RevC WWID: 5001438006FD9A5F Vendor ID: PMCSIERA Model: SRC 8x6G

  Read the article

• Mouse scroll wheel in Citrix

  - by molecule

  Hi all, One of my users is experiencing a problem whereby the mouse scroll does not work on the Citrix published application. I have tried to install mouse drivers on his local PC as well as swapping the USB with a PS/2 mouse but still no go. I have researched this issue for a few days but have not been able to find a fix. PC is running Windows XP and ICA client is version 10 I am pretty sure its a problem local to that PC since every other user using the application published on the same server are not having any issues. What could it be?

  Read the article

• Cannot find grldr in all devices

  - by blockhead

  I'm running wubi on XP machine. Started out originally with 8.04, and gradually upgraded to 10.04. Recently, I was creating linux bootable USB drive, and put it in my system to see if it would work. After booting the LiveOS, and rebooting my machine, I know get the error Cannot find grldr in all devices when booting Ubuntu. I don't know what grldr is, but I assume it is the GRUB Loader. Did booting the LiveOS screw with my MBR perhaps? How can I fix this, and if not, is it possible to reinstall wubi, without losing anything of what I have now?

  Read the article

• keyboard key mapping gone haywire

  - by arvind

  I have a Sony VGN-CR353 running Windows 7 Ultimate. For typing purposes I use two keyboards: The Inbuilt Laptop Keyboard A Standard External Desktop Grade USB Keyboard Since yesterday, My inbuilt keyboard's keys have gone all awry. This is Similar to http://superuser.com/questions/11537/keyboard-keys-not-working-or-resulting-in-the-wrong-key But the high point is that the external keyboard is working just fine. I have already tried System Restore, Reinstalling Keyboard Drivers etc. but to no avail. This is really bugging. Please Help. Thanks in Advance.

  Read the article

• Install Linux Mint on PC without bootable CD

  - by crosenblum

  Unfortunately my PC's CD drive is not bootable; I have such a mixture of SATA and IDE drives, so until I have more money to redo my controller setup, I can't boot from any cd. Currently, I have a DVD burned with latest version of Linux Mint, and I have an USB drive with an old version of Mint. I have a partition ready to install Linx Mint into, but no idea how to install it, since I can only boot to my hard drive. I am totally unable to boot to CD, so that is definitely out. My main partition is WinXP Pro SP3. Is there software I can use to format my Linux partition, so that I can then just copy Mint over to that partition? Or is there a better way to install linux mint? I have to do it within Windows XP, since that's all that I can boot right now. I have considered Mint4Win, but that doesn't allow a full installation of Linux Mint. Any ideas?

  Read the article

• Changing privilege rights on Arch Linux for a particular program

  - by sherrellbc

  I am quite new to linux and have had issues surrounding every program that I install. Basically, anything that is placed outside of my home directory requires a sudo call prior to opening/executing. I cannot write to files, open usb devices, or run programs that exist outside of this directory (specifically, above this directory). I know this is a privilege problem, but I come here to ask how this can be permanently stopped. How can I configure things such that when programs are installed I do not have to manually find the executable and change its privilege requirements?

  Read the article

• Wyse Z Class Thin Client (WES7) Image Deployment

  - by nsr81

  We are currently working on deploying a few Wyse WES7 thin clients (Z Class, exact model escapes me at the moment). We have WDM setup, and are able to see new clients show up, interact with them, pull/push images. Our current workflow is something like this: Unpack & boot up the device Disable Windows Firewall, reboot Device shows up in WDM Publish our custom image to the new device. My question is whether or not there is a way I can bypass step 2, and put my image on the client right out of the box. Either using PXE or USB boot disk, such that I can boot into some sort of menu and tell the client to pull a particular image from the WDM server. With HP thin clients, we have a rule setup which detects new clients on the network and pushes our custom image to them first time they show up. I haven't been able to figure it out with Wyse.

  Read the article

• Is there a Linux distro that will easily run "embedded style" on a Raspberry Pi?

  - by Dan Harper

  I need a Linux distro that will give me the following: Run on a Raspberry Pi Can reliably survive power loss (like via a read-only filesystem) I've been able to hunt down some documentation on how to change a regular Linux distro over to read-only mode. I was hoping that there would be a distro already built that was designed to run in an embedded environment. I don't need many packages or drivers, just enough to have the Pi working with USB/Ethernet. I don't need any GUI interface or anything, this will just be running a custom service built in C. Does anyone know of a distro that would fit?

  Read the article

• Backup strategy for Windows Server 2008 R2 and Hyper-V

  - by winserveradmin

  I am in the process of planning a Hyper-V deployment with SCVMM 2008 R2. I have several VMs on VMWare Player (temporary solution) for stuff like Sharepoint 2007, 2010, and a couple of other server apps. I want to develop a resilient backup plan for this. On the software side, Data Protection Manager 2010 will support all of the server apps I run (sQL Server 2008 R2, Sharepoint, Exchange, etc). But on the hardware side (storage), what is the best way to go? Drobo seems to have issues with Hyper-V juding by a few threads on here and doesn't support DPM 2010 (which is in beta anyway) but not even the 2007 version (see http://www.drobo.com/support/best_practices.php). What storage device would work well? Do I need a home server or just an external usb drive? Capacity wise, 2tb will probably be best so I can have a small archive and implement a round-robin system. Thanks

  Read the article

• MS Office Communicator: Long delays in setting up audio connection when starting a call

  - by geofftnz

  I am using Microsoft Office Communicator with a USB headset as my work phone. OCS is connected to our PABX so we can take and make calls to regular, non-OCS phones. When making an external call to a cellphone, it can take up to 5-10 seconds for audio to start flowing. eg: Work Phone Cellphone - dial cellphone (ringing) (ringing) answer cellphone (hearing nothing) speak "1" . speak "2" . speak "3" . ... . speak "14" hear "15" speak "15" hear "16" speak "16" Has anyone experienced this kind of thing with an OCS setup? Any pointers?

  Read the article

• Choosing a very basic Linux distro with minimal boot time?

  - by user30961

  I've had Ubuntu for a year now, like it but it doesn't match my needed configuration for my old laptop. So... I am using Linux mainly for webapps so I don't care much about user interface. What I need is a distro which is small enough to install on a SD memory card (or USB) since I am removing the hard drive, all my data is in the cloud. I also want it to have as short boot time as possible. I tried Puppy Linux and it seems ok but it had preinstalled looots af small apps I don't need, I would really like to have a distro with minimal preinstallations and add them on my own. So what are my choices and why would you recommend these?

  Read the article

• How powerful of a PC do you need to edit HD videos?

  - by Xeoncross

  I have a Core2Quad Q8200 (2.3GHz) with 4GB of RAM, a 512MB PCIe video card, and a SATA-2 HD. Yet it still isn't fast enough to edit 720i/p video in Sony Vegas or Adobe Premiere/Aftereffects. My RAM usage never peaks over 1.6GB, but my CPU cores make it to 95% quick! Right now the preview panes in all these programs lag to bad to actually work on the videos. I get to see 1-3 frames every second or two! So how fast do I have to go? At what point will my CPU be fast enough to actually edit these videos? I have to assume that regular people and their regular sub $2k computers can actually work with this footage. Another way to answer this is, how fast is the PC you used to edit videos? Update: I'ts worth noting that now that I have Adobe Pre/AF CS4 I am more interested in getting that working than my older Vegas 6. If you didn't have to re-run RAM preview every, single, time you made one change it would be my answer. But since I like to test many filters and effects before choosing one - I have to re-render a 1-sec section of footage over-and-over and it drives me nuts waiting. Perhaps a motherboard with Dual Xeon chips or something would be able to handle this. It would probably be as much as a dual-crossfire setup and would also speed up other applications.

  Read the article

• Can't Install Windows 2008 R2 on Lenovo Laptop With SSD

  - by Ben

  I am trying to install Windows Server 2008 R2 on a new Lenovo X201 or T410 laptop. Setup halts with the following pop-up: A required CD/DVD device driver is missing. If you have a driver floppy disk, CD, DVD, or USB flash drive, please insert it now. Note: If the windows installation media is in the CD/DVD drive you can safely remove it for this step. The CD drive is obviously working, as it's booting from CD to get to this point. The only thing I can think is that it is to do with the fact they have SSD disks in - but that's just a guess. (Edit - One extra thing that may or may not be relevant: it's the 64 bit version of Server 2008 R2)

  Read the article

• Logitech MK300 : "no driver found"

  - by Oystein

  Hi I bought kewyboard and mouse from Logitech. The model is MK300. I wanna run 64-bits Windows 7 with this. When I connect the USB-receiver, Windows is trying to install it but gives me the error message: "no driver found". I tried to download SetPoint 4.80, but that didn't help. I have rebooted the computer several of times, tried different USB'ports, and have allso tried menye different mouses from Logitech. Non of this works. Have someone any suggestions for how I can fix my problem?

  Read the article

• Print server not being recognized after switching router and upgrading to 64 bit

  - by picardo

  I recently upgraded Windows 7 from 32 bit to 64 bit. I also switched my router from a very old model of Netgear to TP-Link. Before these updates, I had been using a USB print server by IOGear. After the updates, I took care to reinstall the drivers for both the print server and the printer, and picked the option to install a printer via TCP/IP, but no matter what I did, the driver software couldn't locate the print server on my network. I hit refresh, restarted my machine, turned off the firewalls and tried again. Still nothing. I'm at my wit's end. What else is left to try? Edit: More info. The print server is connected to the router via LAN line. The computer is connected to the router with a wireless connection.

  Read the article

• Windows lowers volume because of "communication"

  - by SnippetSpace

  Randomly, or at system sound (usb connect for example) Windows 8 lowers the volume of all other sources. (Same problem can exist on windows 7, just look online). This is happening because of the "communication detection" made to detect phone calls and then lower volume. But in my case it happens all the time without reason as if windows always considers myself in a call. Do any of you have the same problem? is this a driver issue or a windows issue? I know this has been posted many times but they usually just tell you to turn off the setting above. I'm looking for an explanation or a solution :). Thanks for your feedback and ideas.

  Read the article

• What is this jumper for on my new motherboard?

  - by jasondavis

  I am building a new PC, I just got my motherboard in the mail today. It is a ASRock X58 Extreme 3. I am reading over the manual for it and one of the jumpers says this. There is a 3 pin jumper labeled 1 2 3, with pins 1 and 2 shorted by default it is "+5v" If I manually change it to short jumper pins 2 and 3 instead of 1 and 2 then it will be "+5vSB (standby) for PS/2 or USB wake up events. So I am confused as to exactly what this is for. Can someone explain what it means, why I would want one other the other?

  Read the article

• Migrate installation from one HDD to another?

  - by dougoftheabaci

  I have a server with a 64 GB SSD inside. It runs just fine, but occasionally there's a hiccup that causes it to nearly fill up. When that happens my server starts to lockup and generally misbehave. I'm looking to buy a bigger SSD (either 128 GB or 256 GB) but I'm a bit unsure of how best to make the transition. For a start, I don't have an external monitor. If I need one I'll have to borrow it from work. Most of the time I just SSH into the server from my iMac. The only solution I can think of would be to buy two FW800 2.5" cases, boot from the 64 GB SSD and clone it to the 128 GB SSD. Seem a bit excessive but it might be my best option. I do have more than one SATA port on my server, but they're all currently being use for storage drives. They don't mount by default, so I could unplug them and just have the two SSDs and do the whole thing via SSH. This is another option I'm considering. My main concern with either is how best to make sure everything goes across. I want a carbon copy of the first one onto the second. This is especially important because I have a ZFS volume (my storage) and I'm a bit unfamiliar with how to move everything across. I could just start fresh and reinstall everything on the SSD, but that seems like extra trouble I don't need. So any advice on how best to achieve my goals would be appreciated. Thanks! Server is running Ubuntu Server 12.04. The iMac has 10.8.1.

  Read the article

• Best way to fix security problems caused by windows updates?

  - by Chris Lively

  I have a laptop running Windows 7 32-bit. Last nights security updates caused my logitech mouse to stop working (specifically, it caused several USB ports to stop altogether). After reviewing the system event log I found that the IPBusEnum component was failing due to an activation security error. A little more research and I found that this was caused by the TrustedInstaller replacing the security permissions on those keys and generally mucking them up. To fix this I had to open regedit, take ownership of ALL the keys related to IPBusEnum and force it to use the inherited permissions from the tree. Is there a better way to fix this when MS screws up the updates? I would hate to have to walk around to a number of machines and manually fix the registry key security settings.

  Read the article

• Robocopy to a drive connected to a wlan router fails

  - by Ville Koskinen

  I have a wireless router and an USB hard drive connected to it. Basic file access on the command line and Explorer works flawlessly after having set up some options on the router and mapping to some folders with net use k: \\ROUTER\Folder1 /user:MYLAPTOP\Me password /persistent:yes net use n: \\ROUTER\Folder2 /user:MYLAPTOP\Me password /persistent:yes Robocopy (and using SyncToy for that matter) to a network drive however fails: robocopy c:\Files k:\Backup /MIR /Z gives There is not enough space on the disk. 2010/01/05 09:52:11 ERROR 112 (0x00000070) Accessing Destination Directory N:\ Waiting 30 seconds... The error message is misleading: there is plenty of space on the disk and the folders I'm copying are small. The router is an ASUS WL-500gp with a standard firmware. I'd appreciate if someone would be able to explain what is causing the problem and, if possible, how to fix it.

  Read the article

• Why did my Cisco router hang?

  - by Mike Pennington

  We have a Cisco 1841 in our storage IDF that was originally running a 12.4(1) IP-BASE image; I wanted to upgrade to an advancedservicesk9-mz image, but the flash did not have enough space, so I deleted the running image. Later I tried inserting a larger CF from a Catalyst4500, which crashed the 1841 router (now without a bootable image). Using another 1800 series router, I loaded the 12.4(25g) advancedservicesk9 image and verified the image checksums. I set the confreg to 0x2102 from rommon and booted the new image; however the 1841 now hangs indefinitely after printing the IOS export control banner. I have tried four other images, all with the same results. What is wrong with this router? UPDATE 1: I tried loading images from a FAT16-formatted USB, but this didn't work either. I also tried tftpdnld from rommon, but got a get_mac_address(): Search T_IDPROM_MACADDR (0xc3) failed Illegal MAC address. error and the file would not load.

  Read the article

• Using ethernet cables?

  - by Farhad Yusufali

  I have an HDTV which supports internet connectivity through an ethernet port or wirelessly (but this requires an additional wireless USB adapter, which I don't have). I also have a blue ray player than supports internet connectivity through an ethernet port or wirelessly (natively - no other devices are needed). I want to connect my TV to the internet but my router is too far away. My blueray player however is already connected wirelessly. If I connected my TV to my Blueray player via ethernet, would my TV be able to connect to the internet? To clarify: Wireless Signal - Blue Ray Player - Ethernet Cable - TV Would this work?

  Read the article

• Windows 2008 and Truecrypt: can't access shared folder called "media"

  - by Sajee

  On my Windows 2008 system, I've attached an external USB drive that's encrypted using Truecrypt. Once I mounted the Truecrypt drive, I share some of the directories from that drive using Windows file sharing. I tried sharing a folder called "media" and when I try to access that folder from a Vista client on my LAN via \myserver\media, I get this error: \myserver\media is not accessible. You might not have permission to use this network resource. Contact the administrator of this server to find out if you have access permissions. An unexpected network error occurred. If I share the folder media under some name such as fizzbuzz then I can access \myserver\fizzbuzz w/o any errors. Any clues as to why this is happening? Related: http://serverfault.com/questions/27684/windows-2008-and-truecrypt-how-to-automatically-mount-shared-folders-after-rest

  Read the article

• ZFS: Mirror vs. RAID-Z

  - by John Clayton

  I'm planning on building a file server using OpenSolaris and ZFS that will provide two primary services - be an iSCSI target for XenServer virtual machines & be a general home file server. The hardware I'm looking at includes 2x 4-port SATA controllers, 2x small boot drives (one on each controller), and 4x big drives for storage. This allows one free port per controller for upgrading the array down the road. Where I'm a little confused is how to setup the storage drives. For performance, mirroring appears to be king. I'm having a hard time seeing what the benefit would be of using RAIDZ over mirroring would be. With this setup I can see two options - two mirrored pools in one stripe, or RAIDZ2. Both should protect against 2 drive failures, and/or one controller failure...the only benefit of RAIDZ2 would be that any 2 drives could fail. The storage should be 50% of capacity in both cases, but the first should have much better performance, right? The other thing I'm trying to wrap my mind around is the benefit of mirrored arrays with more than two devices. For data integrity what, if any, would be the benefit of a RAIDZ over a three-way mirror? Since ZFS maintains file integrity what does RAIDZ bring to the table...doesn't ZFS's integrity checks negate the value of RAIDZ's parity?

  Read the article

< Previous Page | 208 209 210 211 212 213 214 215 216 217 218 219  | Next Page >