Search Results

Search found 8465 results on 339 pages for '40 love'.

Page 222/339 | < Previous Page | 218 219 220 221 222 223 224 225 226 227 228 229  | Next Page >

• vconfig created virtual interface and trunking - is the the interface untagged or tagged for that VLAN ID?

  - by kce

  I am trying to setup an additional VLAN on our Debian-based router/firewall (which exists as a virtual machine on Hyper-V), our core switch (an HP Procurve 5406) and a remote HP ProCurve 2610 that is connected via a WAN Transparent Lan Service (TLS) link. Let's work backwards from the network edge: The Debian server has an external connection attached to eth0. The internal interface is eth1, which is connected directly from our Hyper-V host to the 5406. The port that eth1 is attached to is setup as Trk12. The 2610 is attached to Trk9 (which trunks a whole slew of VLANs - Trk9 is our TLS head). I can successfully ping the management IP addresses for my VLAN from both switches but I cannot ping, from either switch, the virtual interface for my new VLAN on the Debian-base router and firewall. The existing VLAN works fine. What gives? The port eth1 is attached to is a trunk, the existing VLAN (ID 98) is untagged on the trunk, the new VLAN (ID 198) is tagged. VLAN 198 is tagged on Trk9 on the 5406 and on the 2610. I can ping the other switch's management IP (10.100.198.2 and 10.100.198.3) from the other respective switch. That leg of the VLAN works - however I cannot communicate with eth1.198's 10.100.198.1. I feel like I'm missing something elementary but what it is remains illusive to me. I suspect the issue is with the vconfig created eth1.198. It should pass the tagged VLAN 198 packets correct? But they cannot seem to get any further than the 5406. Communication on the existing VLAN 98 works fine. From the Debian box: eth1: eth1 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.0.1 Bcast:10.100.255.255 Mask:255.255.0.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12179786 errors:0 dropped:0 overruns:0 frame:0 TX packets:20210532 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1586498028 (1.4 GiB) TX bytes:26154226278 (24.3 GiB) Interrupt:9 Base address:0xec00 eth1.198: eth1.198 Link encap:Ethernet HWaddr 00:15:5d:34:5e:03 inet addr:10.100.198.1 Bcast:10.100.198.255 Mask:255.255.255.0 inet6 addr: fe80::215:5dff:fe34:5e03/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1496 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:72 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:3528 (3.4 KiB) # cat /proc/net/vlan/eth1.198: eth1.198 VID: 198 REORDER_HDR: 0 dev->priv_flags: 1 total frames received 0 total bytes received 0 Broadcast/Multicast Rcvd 0 total frames transmitted 72 total bytes transmitted 3528 total headroom inc 0 total encap on xmit 39 Device: eth1 INGRESS priority mappings: 0:0 1:0 2:0 3:0 4:0 5:0 6:0 7:0 EGRESS priority mappings: # ip route 10.100.198.0/24 dev eth1.198 proto kernel scope link src 10.100.198.1 206.174.64.0/20 dev eth0 proto kernel scope link src 206.174.66.14 10.100.0.0/16 dev eth1 proto kernel scope link src 10.100.0.1 default via 206.174.64.1 dev eth0 # iptables -L -v Chain INPUT (policy DROP 6875 packets, 637K bytes) pkts bytes target prot opt in out source destination 41 4320 ACCEPT all -- lo any anywhere anywhere 11481 1560K ACCEPT all -- any any anywhere anywhere state RELATED,ESTABLISHED 107 8058 ACCEPT icmp -- any any anywhere anywhere 0 0 ACCEPT tcp -- eth1 any 10.100.0.0/24 anywhere tcp dpt:ssh 701 317K ACCEPT udp -- eth1 any anywhere anywhere udp dpts:bootps:bootpc Chain FORWARD (policy DROP 1 packets, 40 bytes) pkts bytes target prot opt in out source destination 156K 25M ACCEPT all -- eth1 any anywhere anywhere 215K 248M ACCEPT all -- eth0 eth1 anywhere anywhere state RELATED,ESTABLISHED 0 0 ACCEPT all -- eth1.198 any anywhere anywhere 0 0 ACCEPT all -- eth0 eth1.198 anywhere anywhere state RELATED,ESTABLISHED Chain OUTPUT (policy ACCEPT 13048 packets, 1640K bytes) pkts bytes target prot opt in out source destination From the 5406: # show vlan ports trk12 detail Status and Counters - VLAN Information - for ports Trk12 VLAN ID Name | Status Voice Jumbo Mode ------- -------------------- + ---------- ----- ----- -------- 98 WIFI | Port-based No No Untagged 198 VLAN198 | Port-based No No Tagged

  Read the article

• PC runs very slowly for no apparent reason

  - by GalacticCowboy

  I have a Dell Latitude D820 that I've owned for about 2.5 years. It is a Core 2 Duo T7200 2.0GHz, with 2 GB of RAM, an 80 GB hard drive and an NVidia Quadro 120M video card. The computer was purchased in late November of 2006 with XP Pro, and included a free upgrade to Vista Business. (Vista was available on MSDN but not yet via retail, so the Vista Business upgrades weren't shipped until March of '07.) Since we had an MSDN subscription at the time, I installed Vista Ultimate on it pretty much as soon as I got it. It ran happily until sometime in the spring of 2007 when Media Center (which I had never used except to watch DVDs) started throwing some kind of bizarre SQL (CE?) error. This error would pop up at random times just while using the computer. Furthermore, Media Center would no longer start. I never identified the cause of this error. I had the Vista Business upgrade by this time, so I nuked the machine, installed XP and all the drivers, and then the Vista Business upgrade. Again, it ran happily for a few months and then started behaving badly once again. Vista Business doesn't have Media Center, so this exhibited completely unrelated symptoms. For no apparent reason and at fairly random times, the machine would suddenly appear to freeze up or run very slowly. For example, launching a new application window (any app) might take 30-45 seconds to paint fully. However, Task Manager showed very low CPU load, memory, etc. I tried all the normal stuff (chkdsk, defrag, etc.) and ran several diagnostic programs to try to identify any problems, but none found anything. It eventually reached the point that the computer was all but unusable, so I nuked it again and installed XP. This time I decided to stick with XP instead of going to Vista. However, within the past couple of months it has started to exhibit the same symptoms in XP that I used to see in Vista. The computer is still under Dell warranty until December, but so far they aren't any help unless I can identify a specific problem. A friend (partner in a now-dead business) has an identical machine that was purchased at the same time. His machine exhibits none of these symptoms, which leads me to believe it is a hardware issue, but I can't figure out how to identify it. Any ideas? Utilities? Seen something similar? At this point I can't even identify any pattern to the behavior, but would be willing to run a "stress test"-style app for as long as a couple days if I had any hope that it would find something. EDIT July 17 I'm testing jerryjvl's answer regarding the video card, though I'm not sure it fully explains the symptoms yet. This morning I ran a video stress test. The test itself ran fine, but immediately afterward the PC started acting up again. I left ProcExp open and various system processes were consuming 50-60% of the CPU but with no apparent reason. For example, "services.exe" was eating about 40%, but the sum of its child processes wasn't higher than about 5%. I left it alone for several minutes to settle down, and then it was fine again. I used the "video card stability test" from firestone-group.com. Its output isn't very detailed, but it at least exercises the hardware pretty hard. EDIT July 22 Thanks for your excellent suggestions. Here is an update on what I have tried so far. Ran memtest86, SeaTools (Seagate), Hitachi drive fitness test, video card stability test (mentioned above). The video card test was the only one that seemed to produce any results, though it didn't occur during the actual test. I defragged the drive (again...) with JkDefrag I dropped the video card

  Read the article

• Intermittent lockups, unable to diagnose in over a year

  - by Magsol

  Here's a real doosie; I may just give my firstborn child to whomever helps me solve this problem. In July 2008, I assembled what would be my desktop computer for graduate school. Here are the specs of the machine I built: Thermaltake 750W PSU Corsair Dominator 2x2GB 240-pin SDRAM Thermaltake Tower Asus P5K Deluxe Motherboard Intel Core 2 Quad Q9300 2.5GHz CPU 2 x GeForce 8600 GT WD Caviar Blue 640GB hard drive CD burner DVD burner Soon thereafter, I ordered a new motherboard (because I was an idiot; that first motherboard supported CrossFire, not SLI), an Asus P5N-D. I was originally running Windows XP SP3. Pretty much right into the start of the fall semester, my desktop would simply lock up after awhile. If my system was largely idling, it would be after 1-3 days. If was gaming, it often happened an hour or two into my gaming session, indicating a link to activity level. Here's where it started getting interesting. I started looking at the system temps. The CPU was warmer than it should have been (~60s C), so I purchased some more efficient cooling compound a way better cooler for it. Now it hardly goes over 40 C. Intel was even kind enough to swap it out for free, just to rule it out. Lockups continued. The graphics cards were also running pretty warm: about 60 C idling. Removing one of them seemed to improve stability a little bit...as in, it wouldn't lock up quite as frequently, but still always eventually locked up. But it didn't matter which card I used or removed, the lockups continued. I reverted back to the original motherboard, the P5K Deluxe. Lockups continued. I purchased an entirely new motherboard, eVGA's nForce 750i. Lockups continued. Ran memtest86+ over and over and over, with no errors. Even RMA'd the memory. Lockups continued. Replaced the PSU with a Corsair 750W PSU. Lockups continued. Tried disconnecting all IDE drives (HDDs are SATA). Lockups continued. Replaced both graphics cards with a single Radeon HD 4980. Average temps are now always around 50 C when idling, 60 C only when gaming. Lockups continued. Throughout the whole ordeal, the system has been upgraded from Windows XP SP3 to Vista 32-bit, to Vista 64-bit, and is now at Windows 7 64-bit. Lockups have occurred at every step along the way (each OS was in place for at least a few months before the next upgrade). Edit: By "upgrade" I mean clean install each time. In addition to those reformats, I have performed many, many other reformats of the system and a reinstall of whatever OS had been previously installed in an attempt to rectify this problem, to no avail./Edit When the system locks up, there's no blue screen, no reboot, no error message of any kind. It simply freezes in place until I hit the reset button. Very, very rarely, once Windows boots back up, the system informs me that Windows has recovered from an error, but it can never find the source aside from some piece of hardware. I've swapped out every component in this computer, and there are more fans in it than I care to count...though for the sake of completeness: top 80mm case fan (out) rear 80mm case fan (out) rear 120mm case fan (out) front 120mm case fan (in) side 250mm case fan (in) giant CPU fan on-board motherboard fan (the eVGA board) triple-fan memory setup (came with the memory) PSU internal fan another 120mm fan I stuck on the underside of the video card to keep hot air from collecting at the bottom of the case I'm truly out of ideas. ANY help at all would be oh-so-very GREATLY appreciated. Thank you!

  Read the article

• nginx server over https using up all available file handles (upd: infinite loop?)

  - by mmr

  Hi all, So I have an nginx server that's working over https with Sinatra. When I try to download a jnlp file in a configuration that works fine over Mongrel and http (no s), the nginx server fails to serve the file with a 504 error. Subsequent checking of the logs states that this error is due to overflowing the available number of file handles, ie, "24: too many open files". Running sudo lsof -p <nginx worker pid> gets me a huge list of files, all looking like: nginx 1771 nobody 11u IPv4 10867997 0t0 TCP localhost:44704->localhost:https (ESTABLISHED) nginx 1771 nobody 12u IPv4 10868113 0t0 TCP localhost:https->localhost:44704 (ESTABLISHED) nginx 1771 nobody 13u IPv4 10868114 0t0 TCP localhost:44705->localhost:https (ESTABLISHED) nginx 1771 nobody 14u IPv4 10868191 0t0 TCP localhost:https->localhost:44705 (ESTABLISHED) nginx 1771 nobody 15u IPv4 10868192 0t0 TCP localhost:44706->localhost:https (ESTABLISHED) nginx 1771 nobody 16u IPv4 10868255 0t0 TCP localhost:https->localhost:44706 (ESTABLISHED) nginx 1771 nobody 17u IPv4 10868256 0t0 TCP localhost:44707->localhost:https (ESTABLISHED) nginx 1771 nobody 18u IPv4 10868330 0t0 TCP localhost:https->localhost:44707 (ESTABLISHED) nginx 1771 nobody 19u IPv4 10868331 0t0 TCP localhost:44708->localhost:https (ESTABLISHED) nginx 1771 nobody 20u IPv4 10868434 0t0 TCP localhost:https->localhost:44708 (ESTABLISHED) Increasing the number of files that can be opened is no help, because then nginx just blows right past that limit. And no wonder, it looks like it's in some kind of loop to pull all available files. Any idea what's going on, and how to fix it? EDIT: nginx 0.7.63, ubuntu linux, sinatra 1.0 EDIT 2: Here's the offending code. It's sinatra serving jnlp, which I finally figured out: get '/uploader' do #read in the launch.jnlp file theJNLP = "" File.open("/launch.jnlp", "r+") do |file| while theTemp = file.gets theJNLP = theJNLP + theTemp end end content_type :jnlp theJNLP end If I serve this with Sinatra via Mongrel and http, everything works fine. If I serve this with Sinatra and nginx via https, I get the above error. All other parts of the website appear to be equivalent. EDIT: I have since upgraded to passenger 2.2.14, ruby 1.9.1, nginx 0.8.40, openssl 1.0.0a, and no change. EDIT: The culprit appears to be infinite redirects due to using SSL. I don't know how to fix this, other than hosting the jnlp file in the root directory of the server (which I'd rather not do, since it limits me to one jnlp-based app at a time). The relevant lines from nginx.conf: # HTTPS server # server { listen 443; server_name MyServer.org root /My/Root/Dir; passenger_enabled on; expires 1d; proxy_set_header X-FORWARDED_PROTO https; proxy_set_header X_FORWARDED_PROTO https;#the almighty google is not clear on which to use location /upload { proxy_pass https://127.0.0.1:443; } } The funny thing about this is, first, I was putting the jnlp into a directory called 'uploader', not 'upload', but that still appeared to trigger the problem, since that proxy_pass directive appeared in the logs. Second, again, moving the jnlp into root avoided the problem, because there wasn't any of this proxying due to ssl. So, how can I avoid the infinite proxy_pass loop in nginx?

  Read the article

• Installing chrome in Centos 6.2 (Final)

  - by usjes

  I need to install chrome in a dedicated centos server where I only access via ssh, it doesn't have X or any windows graphical stuff. I need it to be able to pack extensions using google-chrome --pack-extension. I tried adding this to /etc/yum.repos.d/google.repo [google-chrome] name=google-chrome - 32-bit baseurl=http://dl.google.com/linux/chrome/rpm/stable/i386 enabled=1 gpgcheck=1 gpgkey=https://dl-ssl.google.com/linux/linux_signing_key.pub And then yum install google-chrome-stable, but there's a huge list of dependencies problems: How can I install chrome without breaking anything else? UPDATE: Ok, I installed perl-CGI from .rpm because yum couldn't find it, now dependencies resolve and it show me this list of packages to install: Dependencies Resolved ============================================================================================================================================================================================================================================= Package Arch Version Repository Size ============================================================================================================================================================================================================================================= Installing: google-chrome-stable x86_64 19.0.1084.52-138391 google-chrome 35 M Installing for dependencies: ConsoleKit x86_64 0.4.1-3.el6 base 82 k ConsoleKit-libs x86_64 0.4.1-3.el6 base 17 k GConf2 x86_64 2.28.0-6.el6 base 964 k ORBit2 x86_64 2.14.17-3.1.el6 base 168 k bc x86_64 1.06.95-1.el6 base 110 k cdparanoia-libs x86_64 10.2-5.1.el6 base 47 k cups x86_64 1:1.4.2-44.el6_2.3 updates 2.3 M dbus x86_64 1:1.2.24-5.el6_1 base 207 k desktop-file-utils x86_64 0.15-9.el6 base 47 k ed x86_64 1.1-3.3.el6 base 72 k eggdbus x86_64 0.6-3.el6 base 91 k foomatic x86_64 4.0.4-1.el6_1.1 base 251 k foomatic-db noarch 4.0-7.20091126.el6 base 980 k foomatic-db-filesystem noarch 4.0-7.20091126.el6 base 4.4 k foomatic-db-ppds noarch 4.0-7.20091126.el6 base 19 M ghostscript x86_64 8.70-11.el6_2.6 updates 4.4 M ghostscript-fonts noarch 5.50-23.1.el6 base 751 k gstreamer x86_64 0.10.29-1.el6 base 764 k gstreamer-plugins-base x86_64 0.10.29-1.el6 base 942 k gstreamer-tools x86_64 0.10.29-1.el6 base 23 k iso-codes noarch 3.16-2.el6 base 2.4 M lcms-libs x86_64 1.19-1.el6 base 100 k libIDL x86_64 0.8.13-2.1.el6 base 83 k libXScrnSaver x86_64 1.2.0-1.el6 base 19 k libXfont x86_64 1.4.1-2.el6_1 base 128 k libXv x86_64 1.0.5-1.el6 base 21 k libfontenc x86_64 1.0.5-2.el6 base 24 k libgudev1 x86_64 147-2.40.el6 base 59 k libmng x86_64 1.0.10-4.1.el6 base 165 k libogg x86_64 2:1.1.4-2.1.el6 base 21 k liboil x86_64 0.3.16-4.1.el6 base 121 k libtheora x86_64 1:1.1.0-2.el6 base 129 k libvisual x86_64 0.4.0-9.1.el6 base 135 k libvorbis x86_64 1:1.2.3-4.el6_2.1 updates 168 k mailx x86_64 12.4-6.el6 base 234 k man x86_64 1.6f-29.el6 base 263 k mesa-libGLU x86_64 7.11-3.el6 base 201 k nvidia-graphics195.30-libs x86_64 195.30-120.el6 atrpms 13 M openjpeg-libs x86_64 1.3-7.el6 base 59 k pax x86_64 3.4-10.1.el6 base 69 k phonon-backend-gstreamer x86_64 1:4.6.2-20.el6 base 125 k polkit x86_64 0.96-2.el6_0.1 base 158 k poppler x86_64 0.12.4-3.el6_0.1 base 557 k poppler-data noarch 0.4.0-1.el6 base 2.2 M poppler-utils x86_64 0.12.4-3.el6_0.1 base 73 k portreserve x86_64 0.0.4-4.el6_1.1 base 22 k qt x86_64 1:4.6.2-20.el6 base 4.0 M qt-sqlite x86_64 1:4.6.2-20.el6 base 50 k qt-x11 x86_64 1:4.6.2-20.el6 base 12 M qt3 x86_64 3.3.8b-30.el6 base 3.5 M redhat-lsb x86_64 4.0-3.el6.centos base 24 k redhat-lsb-graphics x86_64 4.0-3.el6.centos base 12 k redhat-lsb-printing x86_64 4.0-3.el6.centos base 11 k sgml-common noarch 0.6.3-32.el6 base 43 k time x86_64 1.7-37.1.el6 base 26 k tmpwatch x86_64 2.9.16-4.el6 base 31 k xdg-utils noarch 1.0.2-17.20091016cvs.el6 base 58 k xml-common noarch 0.6.3-32.el6 base 9.5 k xorg-x11-font-utils x86_64 1:7.2-11.el6 base 75 k xz x86_64 4.999.9-0.3.beta.20091007git.el6 base 137 k xz-lzma-compat x86_64 4.999.9-0.3.beta.20091007git.el6 base 16 k Transaction Summary ============================================================================================================================================================================================================================================= Install 62 Package(s) Is it safe to continue and install all that or could I break something already installed?

  Read the article

• Bugzilla : No SASL mechanism found

  - by niteshsinha

  I am using Bugzilla on windows 7. I am using the unofficial Bugzilla installer. I followed the steps accordingly and gave valid credentials wherever required. I open Bugzilla and try to create a new account , but i get the following error. Software error: No SASL mechanism found at C:/Program Files/Bugzilla/perl/perl/site/lib/Authen/SASL.pm line 77 at C:/Program Files/Bugzilla/perl/perl/lib/Net/SMTP.pm line 143 i ran checksetup.pl and found that Authen::SASL and SMTP both are available on my machine. The output of checksetup.pl is as follows. * This is Bugzilla 3.6.3 on perl 5.10.1 * Running on Win7 Build 7600 Checking perl modules... Checking for CGI.pm (v3.33) ok: found v3.49 Checking for Digest-SHA (any) ok: found v5.48 Checking for TimeDate (v2.21) ok: found v2.24 Checking for DateTime (v0.28) ok: found v0.53 Checking for DateTime-TimeZone (v0.79) ok: found v1.10 Checking for DBI (v1.41) ok: found v1.609 Checking for Template-Toolkit (v2.22) ok: found v2.22 Checking for Email-Send (v2.16) ok: found v2.198 Checking for Email-MIME (v1.861) ok: found v1.903 Checking for Email-MIME-Encodings (v1.313) ok: found v1.313 Checking for Email-MIME-Modifier (v1.442) ok: found v1.903 Checking for URI (any) ok: found v1.52 Checking available perl DBD modules... Checking for DBD-Pg (v1.45) ok: found v2.16.1 Checking for DBD-mysql (v4.00) ok: found v4.012 Checking for DBD-Oracle (v1.19) not found The following Perl modules are optional: Checking for GD (v1.20) ok: found v2.44 Checking for Chart (v2.1) ok: found v2.4.1 Checking for Template-GD (any) ok: found v1.56 Checking for GDTextUtil (any) ok: found v0.86 Checking for GDGraph (any) ok: found v1.44 Checking for XML-Twig (any) ok: found v3.34 Checking for MIME-tools (v5.406) ok: found v5.427 Checking for libwww-perl (any) ok: found v5.834 Checking for PatchReader (v0.9.4) ok: found v0.9.5 Checking for perl-ldap (any) ok: found v0.39 Checking for Authen-SASL (any) ok: found v2.15 Checking for RadiusPerl (any) ok: found v0.17 Checking for SOAP-Lite (v0.710.06) ok: found v0.710.10 Checking for JSON-RPC (any) ok: found v0.95 Checking for Test-Taint (any) ok: found v1.04 Checking for HTML-Parser (v3.40) ok: found v3.64 Checking for HTML-Scrubber (any) ok: found v0.08 Checking for Email-MIME-Attachment-Stripper (any) ok: found v1.316 Checking for Email-Reply (any) ok: found v1.202 Checking for TheSchwartz (any) not found Checking for Daemon-Generic (any) not found Checking for mod_perl (v1.999022) not found *********************************************************************** * OPTIONAL MODULES * *********************************************************************** * Certain Perl modules are not required by Bugzilla, but by * * installing the latest version you gain access to additional * * features. * * * * The optional modules you do not have installed are listed below, * * with the name of the feature they enable. Below that table are the * * commands to install each module. * *********************************************************************** * MODULE NAME * ENABLES FEATURE(S) * *********************************************************************** * TheSchwartz * Mail Queueing * * Daemon-Generic * Mail Queueing * * mod_perl * mod_perl * *********************************************************************** * Note For Windows Users * *********************************************************************** * In order to install the modules listed below, you first have to run * * the following command as an Administrator: * * * * ppm repo add theory58S http://cpan.uwinnipeg.ca/PPMPackages/10xx/ * * * Then you have to do (also as an Administrator): * * * * ppm repo up theory58S * * * * Do that last command over and over until you see "theory58S" at the * * top of the displayed list. * *********************************************************************** COMMANDS TO INSTALL OPTIONAL MODULES: TheSchwartz: ppm install TheSchwartz Daemon-Generic: ppm install Daemon-Generic mod_perl: ppm install mod_perl Reading ./localconfig... Checking for DBD-mysql (v4.00) ok: found v4.012 Checking for MySQL (v4.1.2) ok: found v5.1.44-community-log Removing existing compiled templates... Precompiling templates...done. Now that you have installed Bugzilla, you should visit the 'Parameters' page (linked in the footer of the Administrator account) to ensure it is set up as you wish - this includes setting the 'urlbase' option to the correct URL. Press any key to continue . . . Please tell me what should i do. Please note: i am running behind a corporate proxy , SSL/TLS is not used internally but i am giving the smtpUser and smtpPass also.

  Read the article

• How to delete files and folders that cannot be deleted?

  - by glenneroo

  I have a backup copy of a previous Windows' Documents and Settings folder which only contains my original user and within 2 more directories: Favorites and Local Settings. When I try to delete Local Settings I get this error: When I try to delete Favorites, I get this error: I ran this in a cmd shell: attrib *.* -r -a -s -h /s ...but it did not help, nor did it return any errors/warnings. I used Unlocker v1.8.5 and LockHunter repeatedly at multiple levels to see if any files are in use, but both always say: No Files Locked. Update #1: I was able to rename the directory, which now gives me this warning before (trying to) delete: If I press Yes (or Yes to All) then I get this error: Update #2: I let chkdsk /f run which required a reboot since it's on my primary system partition. During Stage 2 scanning, I received about 40 of these: Deleting an index entry from index $0 of file 25. ...followed by: Deleting index entry cookies in index $I30 of file 37576. ...but I still get the first error dialog above when trying to delete. I ran chkdsk again, this time: chkdsk /f /r. Produced no messages. Same result when deleting. Update #3: Digging deeper, the 99 is the name of one of many directories located deep in here: C:\Documents and Settings.OLD\User\Local Settings\Application Data\Microsoft\Messenger\[email protected]\SharingMetadata\[email protected]\DFSR\Staging\CS{D4E4AE55-B5E2-F03B-5189-6C4DA6E41788}\ Inside each of those directories were files with names such as: 2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-{C93D01AC-0739-4FD9-88C7-13D2F21A208E}-v2300-Downloaded.frx I noticed that, unlike all the directories, I couldn't rename any of these files. I also noticed that the file + dir names were extremely long: Original directory = 194 characters Filenames = 100+ characters Together the length exceeds the 255-char limit which is bad and would explain the error message I posted in Update #1. Partial Solution: Rename all directories until the total path length is less than 100. Afterwards I was able to rename the .frx files, not to mention delete everything inside the Local Settings directory. This is only a partial solution because these (empty) directories are still not deleteable, C:\1\2\Favorites\Wien\What To Do.. C:\1\2\Favorites\Photography\FIRE Same error as above: Here is what Explorer properties shows for both folders: Update #4 (another partial solution): Using harrymc's answer combined with thoroughly reading through this amazing MS-KB article which contains nearly everyone's idea and then some, inconspicuously titled: You cannot delete a file or a folder on an NTFS file system volume. I was able to delete the 2nd folder C:\1\2\Favorites\Photography\FIRE - the problem being that there was an invisible trailing space at the end. I got lucky when I did an auto-complete whilst playing around with the del "\\?\<path>" command which he suggested. NOTE: A normal del did NOT work, nor did deleting from explorer. Now all that is left is the first directory C:\1\2\Favorites\Wien\What To Do.. (yes I tried endlessly with multiple combinations of the above solution ;) Keep 'em coming! =)

  Read the article

• what is best config for nginx worker_rlimit_nofile and worker_connections 28672

  - by Binh Nguyen

  i have issue of web-brower response ( especially on ie ) very slow, some time time out, and sometime hang out up to 20 seconds for one file redirect 301 when test with "f12 derverloper tool of ie" .. it report wait/start time very long. but after got connected the elements on web weill be dowload and show out fast ( test at xaluan.com ) It most happen when active user on web more than 2100 ( use google real time live analytic ). server running cenos 5 with ngix, apache, 32core cpu, 96G ram, raid 10 sas hdd.. == flowing is my config == user nobody; # no need for more workers in the proxy mode worker_processes 28; #old 32 #good at 24 error_log /var/log/nginx/error.log; #old add in end: info worker_rlimit_nofile 22528; events { worker_connections 22528; use epoll; # you should use epoll here for Linux kernels 2.6.x } http { server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; server_name_in_redirect off; server_names_hash_max_size 10240; server_names_hash_bucket_size 1024; include mime.types; default_type application/octet-stream; server_tokens off; disable_symlinks off; sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 25; #old 5 gzip on; #old on gzip_vary on; gzip_disable "MSIE [1-6]\."; gzip_proxied any; gzip_http_version 1.1; gzip_min_length 1000; gzip_comp_level 6; gzip_buffers 16 8k; ignore_invalid_headers on; client_header_timeout 1m; #3m client_body_timeout 1m; #3m send_timeout 1m; #3m reset_timedout_connection on; connection_pool_size 256; client_header_buffer_size 256k; large_client_header_buffers 4 256k; client_max_body_size 100M; client_body_buffer_size 256k; request_pool_size 32k; output_buffers 4 32k; postpone_output 1460; proxy_temp_path /tmp/nginx_proxy/; client_body_in_file_only on; log_format bytes_log "$msec $bytes_sent ."; limit_conn_zone $binary_remote_addr zone=limit_per_ip:1m; limit_conn limit_per_ip 20; limit_req_zone $binary_remote_addr zone=allips:5m rate=200r/s; limit_req zone=allips burst=200 nodelay; include "/etc/nginx/vhosts/*"; } =========== I have play around with worker config 1- tried increase as some one suggess: worker_rlimit_nofile = worker_connections = worker_processes * 1024 = 32768 2- tried to set low: worker_processes = 28 and other worker at 22582 and other solution too .. but not work cause some time it make server load hight very quick 3- tried to comment out the # worker_rlimit_nofile . so it will be unlimited. it look like solved a bit about issue response time. but it also make server high load quick in peak time... Please help thanks PS: other apache you may have look for help me out thanks Listen 0.0.0.0:8081 User nobody Group nobody ExtendedStatus On ServerAdmin [email protected] ServerName server.xaluan.com LogLevel warn # These can be set in WHM under 'Apache Global Configuration' Timeout 100 TraceEnable Off ServerSignature Off ServerTokens ProductOnly FileETag None StartServers 15 <IfModule prefork.c> MinSpareServers 20 MaxSpareServers 50 #MaxSpareServers 40 </IfModule> ServerLimit 1572 MaxClients 1572 MaxRequestsPerChild 4000 # MaxRequestsPerChild 3000 KeepAlive On KeepAliveTimeout 3 MaxKeepAliveRequests 300 #MaxKeepAliveRequests 130

  Read the article

• AWS Load balancer connection reset

  - by joshmmo

  I have an ELB set up with two instances. The issue I have with it is that when I do not add www. to it, the ELB just hangs. This is some info I get when I spider with wget: Spider mode enabled. Check if remote file exists. --2013-06-20 13:40:54-- http://learning.example.com/ Resolving learning.example.com... 54.xxx.x.x53, 50.xx.xxx.x71 Connecting to learning.example.com|54.xxx.x.x53|:80... connected. HTTP request sent, awaiting response... No data received. Retrying. when I add www. it works great. I have a GoDaddy SSL cert that I added to the listener section that covers 3 domains, www.learning.example.com, files.learning.example.com and learning.example.com. These are my listener settings: - HTTP 80 HTTPS 443 N/A N/A - SSL 443 SSL 443 Change canvasNew (Change) My EC2 instances are running apache2 on Ubuntu 12.04. I will be happy to post my vhosts file if needed. However, when I ran the server with the domains pointing to just one EC2 instance things worked fine. How can I fix this issue for learning.example.com? Why does www work just fine? A second question would be what is the difference between instance protocol and load balancer protocol? EDIT: Here are the dig results for learning.example.com from yesterday. I changed the DNS entry to point to one instance to make sure it was the elb. When I switch it back I will do it for www.learning.example.com ; <<>> DiG 9.9.1-P2 <<>> learning.example.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 20210 ;; flags: qr rd ra; QUERY: 1, ANSWER: 3, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;learning.example.com. IN A ;; ANSWER SECTION: learning.example.com. 2559 IN CNAME canvas-22222222222.us-west-1.elb.amazonaws.com. canvas-22222222222.us-west-1.elb.amazonaws.com. 60 IN A 54.xxx.x.x53 canvas-22222222222.us-west-1.elb.amazonaws.com. 60 IN A 50.xx.xxx.x71 ;; Query time: 83 msec ;; SERVER: 10.x.xx.20#53(10.x.xx.20) ;; WHEN: Thu Jun 20 13:40:47 2013 ;; MSG SIZE rcvd: 137 EDIT 2: Here is some more info that might be helpful. Port Configuration: 80 (HTTP) forwarding to 443 (HTTPS) Backend Authentication: Disabled Stickiness: Disabled(edit) 443 (SSL, Certificate: canvasNew) forwarding to 443 (SSL) Backend Authentication: Disabled So I switched everything to one EC2 IP address to bypass the elb to make sure things are working. It's running great. www and the non-www url work perfectly fine. Its only when I switch things to the ELB that learning.example.com hangs and www.learning.example.com works. Hopefully you can get some ideas flowing.

  Read the article

• Email from my new vps is marked as spam

  - by Chriswede

  I got a new vps from x10vps (x10hosting) and set up the domain via cloudflare. This is what the email looks like: Delivered-To: [email protected] Received: by 10.64.19.240 with SMTP id i16csp357708iee; Tue, 9 Oct 2012 01:29:48 -0700 (PDT) Received: by 10.50.57.130 with SMTP id i2mr908846igq.56.1349771387599; Tue, 09 Oct 2012 01:29:47 -0700 (PDT) Return-Path: <[email protected]> Received: from power.SOURCEAPE.COM ([198.91.90.116]) by mx.google.com with ESMTPS id v8si25630942ica.46.2012.10.09.01.29.46 (version=TLSv1/SSLv3 cipher=OTHER); Tue, 09 Oct 2012 01:29:47 -0700 (PDT) Received-SPF: temperror (google.com: error in processing during lookup of [email protected]: DNS timeout) client-ip=198.91.90.116; Authentication-Results: mx.google.com; spf=temperror (google.com: error in processing during lookup of [email protected]: DNS timeout) [email protected] Received: from nk11p03mm-asmtp010.mac.com ([17.158.232.169]:54276) by power.SOURCEAPE.COM with esmtp (Exim 4.80) (envelope-from <[email protected]>) id 1TLVBD-0004Ig-1Y for [email protected]; Tue, 09 Oct 2012 12:28:43 +0400 I then tried to enable SPF and DKIM and got following massage In order to ensure that SPF or DKIM takes effect, you must confirm that this server is an authoritative nameserver for chvw.de. If you need help, contact your hosting provider. Status: Enabled Warning: cPanel is unable to verify that this server is an authoritative nameserver for chvw.de. [?] and the email header now looks like this: Delivered-To: [email protected] Received: by 10.50.183.227 with SMTP id ep3csp14506igc; Tue, 9 Oct 2012 01:55:23 -0700 (PDT) Received: by 10.50.40.133 with SMTP id x5mr992934igk.32.1349772923717; Tue, 09 Oct 2012 01:55:23 -0700 (PDT) Return-Path: <[email protected]> Received: from power.SOURCEAPE.COM ([198.91.90.116]) by mx.google.com with ESMTPS id ng8si25688859icb.42.2012.10.09.01.55.23 (version=TLSv1/SSLv3 cipher=OTHER); Tue, 09 Oct 2012 01:55:23 -0700 (PDT) Received-SPF: temperror (google.com: error in processing during lookup of [email protected]: DNS timeout) client-ip=198.91.90.116; Authentication-Results: mx.google.com; spf=temperror (google.com: error in processing during lookup of [email protected]: DNS timeout) [email protected]; dkim=neutral (bad format) [email protected] DKIM-Signature: v=1; a=rsa-sha256; q=dns/txt; c=relaxed/relaxed; d=chvw.de; s=default; h=Message-ID:Subject:To:From:Date:Content-Transfer-Encoding:Content-Type:MIME-Version; bh=iugsx3Lx0KnqjR7dj3wyQHnJ9pe/z3ntYEVk80k8rx4=; b=IrYsCtHdoPubXVOvLqxd7sLE/TyQTS5P3OrEg5SSUSKnQQcQ/fWWyBrmsrgkFSsw6jCmmRWMDR09vH5bQRpFPMA57B7pf8QRKhwXOWFBV+GnVUqICsfRjnNPvhx/lNp5; Received: from localhost ([127.0.0.1]:46539 helo=direct.chvw.de) by power.SOURCEAPE.COM with esmtpa (Exim 4.80) (envelope-from <[email protected]>) id 1TLVb0-0004dZ-Kd for [email protected]; Tue, 09 Oct 2012 12:55:22 +0400

  Read the article

• Where is my VMware-ws FreeNAS CIFS(ZFS) bottle-neck?

  - by maka

  Background: I'm building a quiet HTPC + NAS that is also supposed to be used for general computer usage. I'm so far generally happy with things, it was just that I was expecting a little better IO performance. I have no clue if my expectations are unreal. The NAS is there as a general purpose file storage and as a media server for XBMC and other devices. ZFS is a requirement. Question: Where is my bottle-neck, and is there anything I can do config wise, to improve my performance? I'm thinking VM-disk settings could be something but I really have no idea where to go since I'm neither experienced with FreeNAS nor VMware-WS. Tests: When I'm on the host OS and copy files (from the SSD) to the CIFS share, I get around 30 Mbytes/sec read and write. When I'm on my laptop laptop, wired to the network, I get about the same specs. The test I've done are with a 16 GB ISO, and with about 200 MB of RARs and I've tried avoiding the RAM-cache by reading different files than the ones I'm writing ( 10 GB). It feels like having less CPU cores is a lot more efficient, since the resource manager in Windows reports less CPU-usage. With 4 cores in VMware, CPU usage was 50-80%, with 1 core it was 25-60%. EDIT: HD ActiveTime was quite high on SSD so I moved the page file, disabled hibernate and enabled Win DiskCache both on SSD and RAID. This resulted in no real performance difference for one file, but if i transferred 2 files the total speed went up to 50 Mbytes/s vs ~40. The ActiveTime avg also went down a lot (to ~20%) but has now higher bursts. DiskIO is on ~ 30-35 Mbytes/s avgs, with ~100Mb bursts. Network is on 200-250Mbits/s with ~45 active TCP connections. Hardware Asus F2A85-M Pro A10-5700 16GB DDR3 1600 OCZ Vertex 2 128GB SSD 2x Generic 1tb 7200 RPM drives as RAID0 (in win7) Intel Gigabit Desktop CT Software Host OS: Win7 (SSD) VMware Worksation 9 (SSD) FreeNAS 8.3 VM (20GB VDisk on SSD) CPU: I've tried 1, 2 and 4 cores. Virtualisation engine, Preferred mode: Automatic 10,24Gb ram 50Gb SCSI VDisk on the RAID0, VDisk is formatted as ZFS and exposed through CIFS through FreeNAS. NIC Bridge, Replicate physical network state Below are two typical process print-outs while I'm transfering one file to the CIFS share. last pid: 2707; load averages: 0.60, 0.43, 0.24 up 0+00:07:05 00:34:26 32 processes: 2 running, 30 sleeping Mem: 101M Active, 53M Inact, 1620M Wired, 2188K Cache, 149M Buf, 8117M Free Swap: 4096M Total, 4096M Free PID USERNAME THR PRI NICE SIZE RES STATE TIME WCPU COMMAND 2640 root 1 102 0 50164K 10364K RUN 0:25 25.98% smbd 1897 root 6 44 0 168M 74808K uwait 0:02 0.00% python last pid: 2746; load averages: 0.93, 0.60, 0.33 up 0+00:08:53 00:36:14 33 processes: 2 running, 31 sleeping Mem: 101M Active, 53M Inact, 4722M Wired, 2188K Cache, 152M Buf, 5015M Free Swap: 4096M Total, 4096M Free PID USERNAME THR PRI NICE SIZE RES STATE TIME WCPU COMMAND 2640 root 1 76 0 50164K 10364K RUN 0:52 16.99% smbd 1897 root 6 44 0 168M 74816K uwait 0:02 0.00% python I'm sorry if my question isn't phrased right, I'm really bad at these kind of things, and it is the first time I post here at SU. I also appreciate any other suggestions to something, I could have missed.

  Read the article

• Mysqld not starting due to apparent db corruption

  - by pitosalas

  I am very new at admining mysql, and bad for me, something caused the db to get clobbered. There are many error messages in the log that I am not sure how to safely proceed. Can you give some tips? Here's the log: 110107 15:07:15 mysqld started 110107 15:07:15 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 110107 15:07:15 InnoDB: Starting log scan based on checkpoint at InnoDB: log sequence number 35 515914826. InnoDB: Doing recovery: scanned up to log sequence number 35 515915839 InnoDB: 1 transaction(s) which must be rolled back or cleaned up InnoDB: in total 1 row operations to undo InnoDB: Trx id counter is 0 1697553664 110107 15:07:15 InnoDB: Starting an apply batch of log records to the database... InnoDB: Progress in percents: 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 InnoDB: Apply batch completed InnoDB: Starting rollback of uncommitted transactions InnoDB: Rolling back trx with id 0 1697553198, 1 rows to undoInnoDB: Error: trying to access page number 3522914176 in space 0, InnoDB: space name ./ibdata1, InnoDB: which is outside the tablespace bounds. InnoDB: Byte offset 0, len 16384, i/o type 10 110107 15:07:15InnoDB: Assertion failure in thread 3086403264 in file fil0fil.c line 3922 InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/mysql/en/Forcing_recovery.html InnoDB: about forcing recovery. mysqld got signal 11; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=0 read_buffer_size=131072 max_used_connections=0 max_connections=100 threads_connected=0 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_connections = 217599 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd=(nil) Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... Cannot determine thread, fp=0xbffc55ac, backtrace may not be correct. Stack range sanity check OK, backtrace follows: 0x8139eec 0x83721d5 0x833d897 0x833db71 0x832aa38 0x835f025 0x835f7a3 0x830a77e 0x8326b57 0x831c825 0x8317b8d 0x82a9e66 0x8315732 0x834fc9a 0x828d7c3 0x81c29dd 0x81b5620 0x813d9fe 0x40fdf3 0x80d5ff1 New value of fp=(nil) failed sanity check, terminating stack trace! Please read http://dev.mysql.com/doc/mysql/en/Using_stack_trace.html and follow instructions on how to resolve the stack trace. Resolved stack trace is much more helpful in diagnosing the problem, so please do resolve it The manual page at http://www.mysql.com/doc/en/Crashing.html contains information that should help you find out what is causing the crash. 110107 15:07:15 mysqld ended

  Read the article

• Weird Apache Access Logs

  - by user38480

  I see repeated requests like these in my Apache Access Logs and they have been eating up all my CPU. I have a normal WordPress installation. All i changed in the Apache Configuration was changing the DocumentRoot from /var/www/html to /var/www for both ssl and the default configuration. Also, the file referenced in the requests(updatedll.jpeg) does not exist on my server and also isn't referenced in the source code served by any page of the web application. Could this be a security threat? What are these actually and what can i do to stop them. I changed the ip address of my server. They still kept coming. Meaning that somebody is actually hitting the domain name and not the ip address. Why does my server send a 301 for these requests? Shouldn't it be sending a 404? Is it because Wordpress is installed in my root directory and the .htaccess file present for Wordpress is sending a 301 redirect? My disk access logs also seem to have high peaks intermittently. But nobody is actually accessing the site. I see no access logs except these below. Also, i see that all the requests seem to be coming from one of the following 5 ip addresses. 201.4.132.43 - - [05/Jun/2014:07:35:08 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; WOW64; Trident/4.0; BTRS103681; GTB7.5; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; InfoPath.2; OfficeLiveConnector.1.3; OfficeLivePatch.0.0; AskTbATU3/5.15.29.67612; BRI/2)" 187.40.241.48 - - [05/Jun/2014:07:35:08 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; Trident/4.0; GTB7.5; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729)" 186.56.134.132 - - [05/Jun/2014:07:35:10 -0400] "GET /updatedll.jpg HTTP/1.0" 301 428 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows NT 5.1; SV1; .NET CLR 1.1.4322)" 71.223.252.14 - - [05/Jun/2014:07:35:13 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 5.1; Trident/4.0; BTRS31756; GTB7.5; .NET CLR 1.1.4322; .NET CLR 2.0.50727; .NET CLR 3.0.4506.2152; .NET CLR 3.5.30729; .NET4.0C; .NET4.0E; InfoPath.2)" 85.245.229.167 - - [05/Jun/2014:07:35:14 -0400] "GET /updatedll.jpg HTTP/1.1" 301 465 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; Trident/7.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; MAAU; .NET4.0C; BRI/2; .NET4.0E; MAAU)"

  Read the article

• Print directly to CUPS server from non-local clients (Ubuntu 14.04)

  - by OEP

  I set up a CUPS server with a few queues and printing from local clients (the CUPS test page and Samba) seems to work just fine. It seems like the CUPS server is denying non-local clients though: 130.127.48.70 - - [03/Jun/2014:14:29:19 -0400] "POST /printers/m137 HTTP/1.1" 200 390 Validate-Job successful-ok 130.127.48.70 - - [03/Jun/2014:14:29:19 -0400] "POST /printers/m137 HTTP/1.1" 200 339 Create-Job client-error-not-authorized localhost - - [03/Jun/2014:14:40:50 -0400] "POST /printers/m137 HTTP/1.1" 200 410869 Print-Job successful-ok This makes me think I have some sort of host-based restriction in my configuration file, but I can't find it. I've even set my default policy to Allow all only to get the same log message. I'm working from a configuration file which had previously worked on an older version of CUPS, which looks quite similar to the example cupsd.conf. I could be wrong but it looks like that final <Limit All> block ought to allow the actions the logs complain about. MaxLogSize 2000000000 # Log general information in error_log - change "info" to "debug" for # troubleshooting... LogLevel info #AccessLog syslog #ErrorLog syslog #PageLog syslog # Administrator user group... SystemGroup sys root lp # Only listen for connections from the local machine. Listen 0.0.0.0:631 Listen :::631 Listen /var/run/cups/cups.sock ServerName <snipped> # Show shared printers on the local network. Browsing Off BrowseOrder allow,deny # (Change '@LOCAL' to 'ALL' if using directed broadcasts from another subnet.) BrowseAllow @LOCAL # Default authentication type, when authentication is required... DefaultAuthType Basic # Restrict access to the server... <Location /> Order allow,deny Allow all </Location> # Restrict access to the admin pages... <Location /admin> AuthType Default Require user @SYSTEM Encryption Required Order allow,deny Allow all </Location> # Restrict access to configuration files... <Location /admin/conf> AuthType Default Require user @SYSTEM Encryption Required Order allow,deny Allow all </Location> # Set the default printer/job policies... <Policy default> # Job-related operations must be done by the owner or an administrator... <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job CUPS-Move-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> # All administration operations require an administrator to authenticate... <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # All printer operations require a printer operator to authenticate... <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # Only the owner or an administrator can cancel or authenticate a job... <Limit Cancel-Job CUPS-Authenticate-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order allow,deny </Limit> </Policy>

  Read the article

• How to install Delorme StreetAtlas (any version) + GPS inside VirtualBox VM?

  - by hotei

  When I try to run the install program I get a popup message that says the installer program is not a valid executable. Background: I want a GPS with maps on my laptop running Ubuntu 10.4LTS. Unfortunately I can't find a decent native Linux GPS solution with 50 state US street level coverage. I have VirtualBox VMs available for WinXP and Win7 (among others). The VMs work fine with MicroSoft Streets and Trips (2010) and MapNGo 5 (a very! old Delorme product), but while both these products support GPS, they don't support the Earthmate LT-40 USB GPS I already have. I've got pretty much every Delorme Street Atlas they've released in the last decade and none of them will install in a VM. Any help would be much appreciated. Clarification: I've installed the Delorme products from these CDs before and the disks are fine - as long as installation is done on a "physical" machine. Added: I've tried install from an iso as well as the real CD. No difference in result (setup.exe is not a valid executable) The WinXP is SP-2 (held back on purpose at this point - I'll snapshot and fork a later SP to test). The Win2K is SP-6a. Win7(32) VM is whatever updates came out last week. The USB setup is working at least to the point where the GPS device is active in the device list (has an x in the box). At this point its not relevant because the program that needs to read it can't even be installed. Added 9-19: Added wine as harrymc suggested. Initial result was no change. Here's wines error message. The file '/media/Disk1/setup.exe' is not marked as executable. If this was downloaded or copied form an untrusted source, it may be dangerous to run. For more details, read about the executable bit. At first I thought the execute bit was the problem, but looking at several other windows CDs I see that the execute bit is not set on their exe files (which install to VM without error). Still it was worth a shot so I copied the StreetAtlas 9 DVD to my hard disk, changed the on-disk exe files to have the execute bit set and tried to install again. This time the install via wine got me through the installation process. When I start the program it bombs immediately, so we haven't made much real progress so far. I very much prefer the VM solution to wine, so I'm going back to that for now. To recap the VM situation, using an updated XP with SP3 and all recommended hotfixes: StreetAtlas 2009 USA fails with "not marked as executable". StreetAtlas 2007 USA fails with "not marked as executable". StreetAtlas 9 (copyright 2001) fails with "not marked as executable". SteeetAtlas (copyright 1991) fails with "not marked as executable" Delorme Topo 4 (copyright 2002) fails with "not marked as executable". Just about ready to give up. So I switched from XP VM to Win7 VM and tried StreetAtlas 2009 again. This time it installs. Earthmate USB GPS works. WTH? I feel like the monkey who just wrote a line of Shakespear. I'm smiling because it worked, but I have no clue why. I'm awarding the bounty to harrymc because wine did give some useful insight into the problem and a +1 to goyiux as thanks for helping.

  Read the article

• Lockdown users on Windows Server 2012

  - by el.severo

  I set up a Active Directory on a server machine with Windows Server 2012 and I'd like to create some users with limitations like Windows Steady State does in Windows XP (locally). Seen already the Windows SteadyState Handbook (with Windows Server 2008), but I'd like to know if anyone has tried this before, the limitations are the following: 1. Prevent locked or roaming user profiles that cannot be found on the computer from logging on 2. Do not cache copies of locked or roaming user profiles for users who have previously logged on to this computer 3. Do not allow Windows to compute and store passwords using LAN Manager Hash values 4. Do not store usernames or passwords used to log on to the Windows Live ID or the domain 5. Prevent users from creating folders and files on drive C:\ 6. Lock profile to prevent the user from making permanent changes 7. Remove the Control Panel, Printer and Network Settings from the Classic Start menu 8. Remove the Favorites icon 9. Remove the My Network Places icon 10. Remove the Frequently Used Program list 11. Remove the Shared documents folder from My Computer 12. Remove control Panel icon 13. Remove the Set Program Access and Defaults icon 14. Remove the Network Connection(Connect To)icon 15. Remove the Printers and Faxes icon 16. Remove the Run icon 17. Prevent access to Windows Explorer features: Folder Options, Customize Toolbar, and the Notification Area 18. Prevent access to the taskbar 19. Prevent access to the command prompt 20. Prevent access to the registry editor 21. Prevent access to the Task Manager 22. Prevent access to Microsoft Management Console utilities 23. Prevent users from adding or removing printers 24. Prevent users from locking the computer 25. Prevent password changes (also requires the Control Panel icon to be removed) 26. Disable System Tools and other management programs 27. Prevent users from saving files to the desktop 28. Hide A Drive 29. Hide B Drive 30. Hide C Drive 31. Prevent changes to Internet Explorer registry settings 32. Empty the Temporary Internet Files folder when Internet Explorer is closed 33. Remove Internet Options 34. Remove General tab in Internet Options 35. Remove Security tab in Internet Options 36. Remove Privacy tab in Internet Options 37. Remove Content tab in Internet Options 38. Remove Connections tab in Internet Options 39. Remove Programs tab in Internet Options 40. Remove Advanced tab in Internet Options 41. Set a home page (Internet Explorer) 42. Restrict the possibility to change desktop image 43. Restrict the possibility to change wallpaper 44. Restrict usb flash drives Any suggestions for this? UPDATE: As @Dan suggested me I'd like to specify that would be applied to a educational scenario where students can login from a computer and want to add some restrictions to them.

  Read the article

• Can't configure frame relay T1 on Cisco 1760

  - by sonar

  For the past few days I've been trying to configure a data T1 via a Frame Relay. Now I've been pretty unsuccessful at it, and it's been a while, since I've done this so please bare with me. The ISP provided me the following information: 1. IP address 2. Gateway address 3. Encapsulation Frame Relay 4. DLCI 100 5. BZ8 ESF (I think the bz8 was supposed to be b8zs) 6. Time Slot (1 al 24). And what I have configured up until now is the following: interface Serial0/0 ip address <ip address> 255.255.255.252 encapsulation frame-relay service-module t1 timeslots 1-24 frame-relay interface-dlci 100 sh service-module s0/0 (outputs): Module type is T1/fractional Hardware revision is 0.128, Software revision is 0.2, Image checksum is 0x73D70058, Protocol revision is 0.1 Receiver has no alarms. Framing is **ESF**, Line Code is **B8ZS**, Current clock source is line, Fraction has **24 timeslots** (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec. Last module self-test (done at startup): Passed Last clearing of alarm counters 00:17:17 loss of signal : 0, loss of frame : 0, AIS alarm : 0, Remote alarm : 2, last occurred 00:10:10 Module access errors : 0, Total Data (last 1 15 minute intervals): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Data in current interval (138 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs sh int: FastEthernet0/0 is up, line protocol is up Hardware is PQUICC_FEC, address is 000d.6516.e5aa (bia 000d.6516.e5aa) Internet address is 10.0.0.1/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:20:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 191 packets output, 20676 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Serial0/0 is up, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY, loopback not set Keepalive set (10 sec) LMI enq sent 157, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down LMI enq recvd 23, LMI stat sent 0, LMI upd sent 0 LMI DLCI 1023 LMI type is CISCO frame relay DTE FR SVC disabled, LAPF state down Broadcast queue 0/64, broadcasts sent/dropped 2/0, interface broadcasts 0 Last input 00:24:51, output 00:00:05, output hang never Last clearing of "show interface" counters 00:27:20 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1152 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 23 packets input, 302 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 1725 input errors, 595 CRC, 1099 frame, 0 overrun, 0 ignored, 30 abort 246 packets output, 3974 bytes, 0 underruns 0 output errors, 0 collisions, 48 interface resets 0 output buffer failures, 0 output buffers swapped out 4 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up Serial0/0.1 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never Serial0/0.100 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU Internet address is <ip address>/30 MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never And everything seems to be accounted for to me, but apparently I'm missing something. My issue is that I'm stuck on interface up, line protocol down, so the T1 doesn't go up. Any ideas? Thank you,

  Read the article

• How do bots access directories on a server that are not DocumentRoot of public IP address? How do I stop them?

  - by tmsimont

  I have a local network set up with apache2 and "named" running on OpenSuse 13.1 Linux. I used the "named" service to use my computer as a domain server. I set up my router to point to ask my computer for domain lookups, so I have a chance to have it rewrite a bunch of domains on my network to its own local IP, 192.168.0.111 This works great. I use virtual host configuration to allow various domains and subdomains (re-routed to the same IP via named) to pull up different directories in my computer. For example: <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias fmb.wa.net DocumentRoot /home/work/wa.net/fmb </VirtualHost> <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias postrecord.wa.net DocumentRoot /home/work/wa.net/postrecord </VirtualHost> <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias cvalley.wa.net DocumentRoot /home/work/wa.net/cvalley_local </VirtualHost> This makes it possible for me to hit cvalley.wa.net from any device in my network and get the site that lives in /home/work/wa.net/cvalley_local I decided to forward port 80 to this computer, so I could share a few development sites with coworkers. I can't control which site they see with the same named service, because they'd have to use my computer as their domain name server... So I added a line like this: <VirtualHost *:80> ServerName 192.168.0.111 ServerAlias MY.IP.XXX.XX DocumentRoot /home/work/wa.net/cvalley </VirtualHost> Where "MY.IP.XXX.XX" is my public IP address. This works as expected, when you hit my IP address from a public network you see the site that lives in /home/work/wa.net/cvalley. The point of confusion that I have is that there are public IP addresses in my logs in other sites. I would have expected it to be impossible to access other sites in my network, unless the public user somehow figured out what I'm calling my ServerAliases, and is mimicing my domain set up... How can public traffic be hitting my other local sites? How can I recreate this kind of access? Here are some examples of public IP's hitting my VirtualHost sites: 162.253.66.76 - - [15/Aug/2014:19:20:47 -0600] "GET /xmlrpc.php HTTP/1.0" 404 1004 "-" "-" 162.253.66.74 - - [16/Aug/2014:10:50:28 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 185.4.227.194 - - [16/Aug/2014:11:16:45 -0600] "GET http://24x7-allrequestsallowed.com/?PHPSESSID=1rysxtj500143WQMVT%5E_NAZ%5BQ HTTP/1.1" 200 262 "-" "-" 101.226.254.138 - - [16/Aug/2014:13:32:14 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 162.253.66.74 - - [16/Aug/2014:14:26:19 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 212.129.2.119 - - [16/Aug/2014:16:00:51 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 91.240.163.111 - - [16/Aug/2014:18:34:32 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 162.253.66.74 - - [16/Aug/2014:19:02:53 -0600] "GET / HTTP/1.0" 200 262 "-" "masscan/1.0 (https://github.com/robertdavidgraham/masscan)" 122.226.223.69 - - [17/Aug/2014:05:53:09 -0600] "GET http://www.k2proxy.com//hello.html HTTP/1.1" 404 1006 "-" "Mozilla/4.0 (compatible; MSIE 7.0; Windows NT 6.1; WOW64; Trident/6.0; SLCC2; .NET CLR 2.0.50727; .NET CLR 3.5.30729; .NET CLR 3.0.30729; Media Center PC 6.0; .NET4.0C; .NET4.0E)" ::1 - - [17/Aug/2014:10:19:26 -0600] "OPTIONS * HTTP/1.0" 200 - "-" "Apache/2.4.6 (Linux/SUSE) OpenSSL/1.0.1e PHP/5.4.20 (internal dummy connection)" 162.209.65.196 - - [17/Aug/2014:15:31:53 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 111.206.199.163 - - [18/Aug/2014:11:12:56 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 37.187.180.168 - - [18/Aug/2014:15:40:00 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" 62.210.38.226 - - [18/Aug/2014:18:35:16 -0600] "HEAD / HTTP/1.0" 200 - "-" "-" Is there anything that I can do to reliably deny public access by default, but allow it only in one VirtualHost?

  Read the article

• suddenly can't connect to router

  - by Khoi

  I was just downloading some stuff in ubuntu and snap, the connection cut and I can't even connect to my router. And the router, it still works fine, my laptop can connect wirelessly to it as usual. But my main computer (which connects to it directly through cable) can't even ping it. Here is my ipconfig: Windows IP Configuration Host Name . . . . . . . . . . . . : vento Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : No Ethernet adapter Local Area Connection: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Realtek RTL8169/8110 Family Gigabit Ethernet NIC Physical Address. . . . . . . . . : 00-19-DB-4E-6C-56 Ethernet adapter {15B1F740-2F35-4FE4-9FEE-4052AFBAD096}: Media State . . . . . . . . . . . : Media disconnected Description . . . . . . . . . . . : Anchorfree HSS Adapter - Packet Sche duler Miniport Physical Address. . . . . . . . . : 00-FF-15-B1-F7-40

  Read the article

• unmet dependencies in Ubuntu 12.04

  - by lee.O

  I tried today to install a dvb-card on my Ubuntu 12.04 (Linux blauhai-linux 3.2.0-25-generic #40-Ubuntu SMP Wed May 23 20:30:51 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux ). The installation failed with an error. After that, i tried to install python (it was already installed but i got this error): linux:~$ sudo apt-get install git Reading package lists... Done Building dependency tree Reading state information... Done git is already the newest version. You might want to run 'apt-get -f install' to correct these: The following packages have unmet dependencies: python-glade2:i386 : Depends: python:i386 (< 2.5) but it is not going to be installed Depends: python-support:i386 (= 0.3.4) but it is not installable Depends: python:i386 (= 2.4) but it is not going to be installed Depends: libglade2-0:i386 (= 1:2.5.1) but it is not going to be installed Depends: python-gtk2:i386 (= 2.8.6-8) but it is not going to be installed python-numeric:i386 : Depends: python:i386 (< 2.5) but it is not going to be installed Depends: python:i386 (= 2.3) but it is not going to be installed Depends: python-central:i386 (= 0.5.7) but it is not installable E: Unmet dependencies. Try 'apt-get -f install' with no packages (or specify a solution). well, i can read and tried the proposed command, but then i get this: linux:~$ sudo apt-get -f install Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages were automatically installed and are no longer required: libopenal1:i386 libsdl-ttf2.0-0:i386 libkrb5-3:i386 libgconf-2-4:i386 libsm-dev libatk1.0-0:i386 libk5crypto3:i386 libstdc++5:i386 libqt4-declarative:i386 libxcomposite1:i386 libice-dev libgail18:i386 libldap-2.4-2:i386 libao-common libv4l-0:i386 liblcms1:i386 libqt4-qt3support:i386 libroken18-heimdal:i386 libunistring0:i386 libcupsimage2:i386 libgphoto2-port0:i386 libidn11:i386 libnss3:i386 libcaca0:i386 gtk2-engines:i386 libgudev-1.0-0:i386 libjpeg-turbo8:i386 libpthread-stubs0 libcairo-gobject2:i386 libavc1394-0:i386 libjpeg8:i386 libotr2 libaio1:i386 libsane:i386 odbcinst1debian2 odbcinst1debian2:i386 libqt4-test:i386 libqt4-script:i386 libqt4-designer:i386 libsdl-mixer1.2:i386 libqt4-network:i386 libqt4-dbus:i386 libcap2:i386 libproxy1:i386 ibus-gtk:i386 libdbus-glib-1-2:i386 libtdb1:i386 libasn1-8-heimdal:i386 libspeex1:i386 libxslt1.1:i386 libgomp1:i386 libcapi20-3:i386 libibus-1.0-0:i386 libcairo2:i386 libgnutls26:i386 libopenal-data odbcinst libgssapi3-heimdal:i386 libcanberra0:i386 libtasn1-3:i386 libfreetype6:i386 x11proto-kb-dev gtk2-engines-murrine:i386 libwavpack1:i386 libqt4-opengl:i386 libsoup-gnome2.4-1:i386 libv4lconvert0:i386 gstreamer0.10-plugins-good:i386 libc6-i386 lib32gcc1 libqt4-xmlpatterns:i386 librsvg2-common:i386 libdatrie1:i386 xtrans-dev libavahi-common-data:i386 libiec61883-0:i386 lib32asound2 libgdk-pixbuf2.0-0:i386 libsdl-image1.2:i386 libp11-kit0:i386 x11proto-input-dev libwind0-heimdal:i386 libpixman-1-0:i386 libsdl1.2debian:i386 libxaw7:i386 libgdbm3:i386 libcups2:i386 libcurl3:i386 libqtcore4:i386 libxinerama1:i386 libesd0:i386 libmikmod2:i386 libkrb5support0:i386 libxft2:i386 libxt-dev libcroco3:i386 libpulse-mainloop-glib0:i386 libice6:i386 libaa1:i386 libieee1284-3:i386 libgcrypt11:i386 libthai0:i386 libao4:i386 libkeyutils1:i386 libxmu6:i386 libcanberra-gtk0:i386 libvorbisfile3:i386 libqt4-sql:i386 esound-common libxpm4:i386 libqt4-svg:i386 libusb-0.1-4:i386 libgail-common:i386 libxrender1:i386 libhcrypto4-heimdal:i386 libraw1394-11:i386 libnspr4:i386 libshout3:i386 libdv4:i386 libhx509-5-heimdal:i386 libxau-dev libqt4-xml:i386 gstreamer0.10-x:i386 libgettextpo0:i386 libxss1:i386 libgd2-xpm:i386 libheimbase1-heimdal:i386 libtiff4:i386 libsdl-net1.2:i386 libjasper1:i386 libgnome-keyring0:i386 libxtst6:i386 gtk2-engines-pixbuf:i386 libqtgui4:i386 libtag1c2a:i386 librsvg2-2:i386 libavahi-client3:i386 libssl0.9.8:i386 libmpg123-0:i386 libmad0:i386 libsasl2-2:i386 xorg-sgml-doctools libgsoap1 gtk2-engines-oxygen:i386 libfontconfig1:i386 xaw3dg:i386 libpango1.0-0:i386 libsm6:i386 libx11-dev libheimntlm0-heimdal:i386 libpulsedsp:i386 lib32stdc++6 libx11-doc libqt4-sql-mysql:i386 libxcb-render0:i386 libodbc1:i386 libexif12:i386 libqt4-scripttools:i386 librtmp0:i386 libgssapi-krb5-2:i386 libxi6:i386 libqtwebkit4:i386 libxcb1-dev libxp6:i386 libaudio2:i386 libxcursor1:i386 libxcb-shm0:i386 libxt6:i386 libxv1:i386 libsasl2-modules:i386 libavahi-common3:i386 libxrandr2:i386 x11proto-core-dev libsqlite3-0:i386 libmng1:i386 libgtk2.0-0:i386 libxdmcp-dev libpthread-stubs0-dev libltdl7:i386 libkrb5-26-heimdal:i386 libssl1.0.0:i386 glib-networking:i386 libgpg-error0:i386 libsoup2.4-1:i386 libgphoto2-2:i386 libtag1-vanilla:i386 libaudiofile1:i386 libglade2-0:i386 Use 'apt-get autoremove' to remove them. The following extra packages will be installed: default-jre default-jre-headless icedtea-6-jre-cacao icedtea-6-jre-jamvm icedtea-netx icedtea-netx-common libglade2-0:i386 libpython3.2 openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib python3 python3-minimal python3-uno python3.2 python3.2-minimal Suggested packages: icedtea-plugin sun-java6-fonts fonts-ipafont-gothic fonts-ipafont-mincho ttf-telugu-fonts ttf-oriya-fonts ttf-kannada-fonts ttf-bengali-fonts python3-doc python3-tk python3.2-doc binfmt-support The following packages will be REMOVED: activity-log-manager-control-center aisleriot alacarte apparmor apport apport-gtk apt-xapian-index aptdaemon apturl apturl-common bluez bluez-alsa bluez-alsa:i386 bluez-gstreamer checkbox checkbox-qt command-not-found compiz compiz-gnome compiz-plugins-main-default compizconfig-backend-gconf deja-dup duplicity eog evolution-data-server firefox firefox-globalmenu firefox-gnome-support foomatic-db-compressed-ppds gconf-editor gconf2 gdb gedit gir1.2-mutter-3.0 gir1.2-peas-1.0 gir1.2-rb-3.0 gir1.2-totem-1.0 gir1.2-ubuntuoneui-3.0 gksu gnome-applets gnome-applets-data gnome-bluetooth gnome-contacts gnome-control-center gnome-media gnome-menus gnome-orca gnome-panel gnome-panel-data gnome-session-fallback gnome-shell gnome-sudoku gnome-terminal gnome-terminal-data gnome-themes-standard gnome-tweak-tool gnome-user-share gstreamer0.10-gconf gwibber gwibber-service gwibber-service-facebook gwibber-service-identica gwibber-service-twitter hplip hplip-data ia32-libs ia32-libs-multiarch:i386 ibus ibus-pinyin ibus-table indicator-datetime indicator-power jockey-common jockey-gtk landscape-client-ui-install language-selector-common language-selector-gnome launchpad-integration libcanberra-gtk-module libcanberra-gtk-module:i386 libcanberra-gtk3-module libcompizconfig0 libfolks-eds25 libgksu2-0 libgnome-media-profiles-3.0-0 libgnome2-0 libgnome2-common libgnomevfs2-0 libgnomevfs2-common libgweather-3-0 libgweather-common libgwibber-gtk2 libgwibber2 libmetacity-private0 libmutter0 libpeas-1.0-0 libpurple-bin libpython2.7 libreoffice-gnome librhythmbox-core5 libsyncdaemon-1.0-1 libtotem0 libubuntuoneui-3.0-1 light-themes lsb-release metacity metacity-common mutter-common nautilus-dropbox nautilus-share network-manager-gnome nvidia-common nvidia-settings nvidia-settings-updates onboard oneconf openjdk-7-jdk openjdk-7-jre openprinting-ppds pidgin pidgin-libnotify pidgin-otr printer-driver-foo2zjs printer-driver-ptouch printer-driver-pxljr printer-driver-sag-gdi printer-driver-splix python python-appindicator python-apport python-apt python-apt-common python-aptdaemon python-aptdaemon.gtk3widgets python-aptdaemon.pkcompat python-brlapi python-cairo python-central python-chardet python-configglue python-crypto python-cups python-cupshelpers python-dateutil python-dbus python-debian python-debtagshw python-defer python-dirspec python-egenix-mxdatetime python-egenix-mxtools python-gconf python-gdbm python-gi python-gi-cairo python-glade2:i386 python-gmenu python-gnomekeyring python-gnupginterface python-gobject python-gobject-2 python-gpgme python-gst0.10 python-gtk2 python-httplib2 python-ibus python-imaging python-keyring python-launchpadlib python-lazr.restfulclient python-lazr.uri python-libproxy python-libxml2 python-louis python-mako python-markupsafe python-minimal python-notify python-numeric:i386 python-oauth python-openssl python-packagekit python-pam python-pexpect python-piston-mini-client python-pkg-resources python-problem-report python-protobuf python-pyatspi2 python-pycurl python-pyinotify python-renderpm python-reportlab python-reportlab-accel python-serial python-simplejson python-smbc python-software-properties python-speechd python-twisted-bin python-twisted-core python-twisted-names python-twisted-web python-ubuntu-sso-client python-ubuntuone-client python-ubuntuone-control-panel python-ubuntuone-storageprotocol python-uno python-virtkey python-wadllib python-xapian python-xdg python-xkit python-zeitgeist python-zope.interface python2.7 python2.7-minimal rhythmbox rhythmbox-mozilla rhythmbox-plugin-cdrecorder rhythmbox-plugin-magnatune rhythmbox-plugin-zeitgeist rhythmbox-plugins rhythmbox-ubuntuone screen-resolution-extra sessioninstaller skype software-center software-center-aptdaemon-plugins software-properties-common software-properties-gtk system-config-printer-common system-config-printer-gnome system-config-printer-udev texlive-extra-utils totem totem-mozilla totem-plugins ubuntu-artwork ubuntu-desktop ubuntu-minimal ubuntu-sso-client ubuntu-sso-client-gtk ubuntu-standard ubuntu-system-service ubuntuone-client ubuntuone-client-gnome ubuntuone-control-panel ubuntuone-couch ubuntuone-installer ufw unattended-upgrades unity unity-2d unity-common unity-lens-applications unity-lens-video unity-scope-musicstores unity-scope-video-remote update-manager update-manager-core update-notifier update-notifier-common usb-creator-common usb-creator-gtk virtualbox virtualbox-dkms virtualbox-qt xdiagnose xul-ext-ubufox zeitgeist zeitgeist-core zeitgeist-datahub The following NEW packages will be installed: default-jre default-jre-headless icedtea-6-jre-cacao icedtea-6-jre-jamvm icedtea-netx icedtea-netx-common libglade2-0:i386 libpython3.2 openjdk-6-jre openjdk-6-jre-headless openjdk-6-jre-lib python3 python3-minimal python3-uno python3.2 python3.2-minimal WARNING: The following essential packages will be removed. This should NOT be done unless you know exactly what you are doing! python-minimal python2.7-minimal (due to python-minimal) 0 upgraded, 16 newly installed, 273 to remove and 0 not upgraded. 2 not fully installed or removed. Need to get 39.1 MB of archives. After this operation, 324 MB disk space will be freed. You are about to do something potentially harmful. To continue type in the phrase 'Yes, do as I say!' ?] Thats not good, is it?! Should i run this command or should i run another command to fix this problem? Would be great if somebody can help me. :) Thanks in advance. best regards

  Read the article

• Week in Geek: USDA Chooses Microsoft for Cloud Services Edition

  - by Asian Angel

  This week we learned how to create geeky LED holiday lights with old bottles, dig deeper in Windows Defrag via the command prompt, use Google Chrome’s drag/drop feature to upload files easier, find great gift recommendations by looking through the How-To Geek holiday gift guide, and have fun adding Merry Christmas fonts to our computers. Photo by ntr23. Random Geek Links It has been a busy week, so we have extra news link goodness with information that is good for you to know. USDA making the move to Microsoft The U.S. Department of Agriculture has announced that it has chosen Microsoft to host things like e-mail, instant messaging, and collaboration through the software giant’s Business Productivity Online Suite. Google says it was cut off from USDA project bid Google is claiming that it was not given a chance to bid on a cloud-computing project for the U.S. Department of Agriculture, for which the contract was awarded to rival Microsoft. Apache is being forced into a Java Fork When Oracle rolled over Apache and Google’s objections to its Java plans in December, the scene was set for Apache to leave and, eventually, force a Java code fork. Tumblr explains daylong outage After experiencing an outage that started on Sunday afternoon and stretched through most of the day yesterday, Tumblr has explained what happened. Google demos Chrome OS, launches pilot program During a press briefing this week in San Francisco, Google launched the Chrome application store and demonstrated Chrome OS, its browser-centric netbook operating system. Don’t expect Spotify in U.S. this holiday season As of last week, Spotify had yet to sign a single licensing deal with a major label, after spending more than a year negotiating, multiple music sources told CNET. December 2010 Patch Tuesday will come with most bulletins ever According to the Microsoft Security Response Center, Microsoft will issue 17 Security Bulletins addressing 40 vulnerabilities on Tuesday, December 14. It will also host a webcast to address customer questions the following day. Hacker plants back door in Symbian firmware Indian hacker Atul Alex has had a look at the firmware for Symbian S60 smartphones and come up with a back door for it. PC quarantines raise tough complexities The concept of quarantining PCs to prevent widespread infection is “interesting, but difficult to implement, with far too many problems”, said security experts. Symantec: DDoS attacks hard to defend It has surfaced that the distributed denial of service (DDoS) attacks on Visa and MasterCard Web sites on Wednesday were carried out by a toolkit known as low orbit ion cannon (LOIC). Web Sockets and the risks of unfinished standards Enthusiasm for a promising new standard called Web Sockets has quickly cooled in some quarters as a potential security problem led some browser makers to hastily postpone support. Internet Explorer 9 to get tracking protection Microsoft is making changes to Internet Explorer 9’s security features that will better enable users to keep sites from tracking their activity across browsing sessions. NASA sold PCs with sensitive data NASA failed to remove sensitive data from computers that it sold, according to an audit report released this week. Cybercrooks create fake Amazon receipts The bad guys have created yet another online scam, this one involving fake Amazon receipts. World of Warcraft character move fees waived Until December 22, Blizzard will allow free realm transfers from 25 highly populated servers to alleviate log-in queues or performance issues. (The free transfers are one-way and one-time only.) SpaceX Dragon reaches orbit atop a Falcon with a fiery tail The Space Exploration Technologies corporation has become the first nongovernmental entity to put a vehicle into low Earth orbit. Geek Video of the Week If birds have wings, then why are the Angry Birds using slingshots? Photo by Dorkly Bits. Wait… Birds have Wings, Why are the Angry Ones Using Slingshots? Sysadmin Geek Tips How To Setup Email Alerts on Linux Using Gmail or SMTP Linux machines may require administrative intervention in countless ways, but without manually logging into them how would you know about it? Here’s how to setup emails to get notified when your machines want some tender love and attention. Random TinyHacker Links Red Panda Webcam Support Firefox and the Knoxville Zoo’s Red Panda program. Christmas Icons (Icons we like) Superb set of holiday icons by lgp85 at deviantArt. Download the .zip and use as .png or convert to .ico at Convertico.com or with tiny app Imagicon. Super User Questions Enjoy reading the great answers to this week’s popular questions from Super User Useful USB boot disks? DVD/CD burning .zip: is it more reliable, faster, longer lasting to burn a zip of files rather than the files as a folder? What are other ways to backup my files if I do not have an external drive? Anti virus what is the difference between these all? How can I block all Facebook elements/content? How-To Geek Weekly Article Recap Have you had a busy week between work and preparing for the holidays? Get caught up on your HTG reading with our hottest articles of the week. 20 Windows Keyboard Shortcuts You Might Not Know The 50 Best Registry Hacks that Make Windows Better LCD? LED? Plasma? The How-To Geek Guide to HDTV Technology HTG Explains: Which Linux File System Should You Choose? How to Use and Customize Google Chrome Web Apps One Year Ago on How-To Geek This week’s batch of retro geeky goodness is all about customizing Windows 7. ClassicShell Adds Classic Start Menu and Explorer Features to Windows 7 Get an Aero-Styled Classic Start Menu in Windows 7 Customize the Windows 7 Logon Screen Get the Classic Style Network Activity Indicator Back in Windows 7 How To Enable Check Boxes for Items In Windows 7 The Geek Note We would like you to join us in welcoming Jason Fitzpatrick to the writing staff here at How-To Geek. He started with us this past week, so take some time to read through his articles about the Wii, Kindle, & PlayStation 2 Peripherals and leave a friendly comment to say “Hi”! Got a great tip to share? Make sure to send it in to us at [email protected]. Photo by real00. Latest Features How-To Geek ETC The 50 Best Registry Hacks that Make Windows Better The How-To Geek Holiday Gift Guide (Geeky Stuff We Like) LCD? LED? Plasma? The How-To Geek Guide to HDTV Technology The How-To Geek Guide to Learning Photoshop, Part 8: Filters Improve Digital Photography by Calibrating Your Monitor Our Favorite Tech: What We’re Thankful For at How-To Geek Settle into Orbit with the Voyage Theme for Chrome and Iron Awesome Safari Compass Icons Set Escape from the Exploding Planet Wallpaper Move Your Tumblr Blog to WordPress Pytask is an Easy to Use To-Do List Manager for Your Ubuntu System Snowy Christmas House Personas Theme for Firefox

  Read the article

• C#: System.Collections.Concurrent.ConcurrentQueue vs. Queue

  - by James Michael Hare

  I love new toys, so of course when .NET 4.0 came out I felt like the proverbial kid in the candy store!  Now, some people get all excited about the IDE and it’s new features or about changes to WPF and Silver Light and yes, those are all very fine and grand.  But me, I get all excited about things that tend to affect my life on the backside of development.  That’s why when I heard there were going to be concurrent container implementations in the latest version of .NET I was salivating like Pavlov’s dog at the dinner bell. They seem so simple, really, that one could easily overlook them.  Essentially they are implementations of containers (many that mirror the generic collections, others are new) that have either been optimized with very efficient, limited, or no locking but are still completely thread safe -- and I just had to see what kind of an improvement that would translate into. Since part of my job as a solutions architect here where I work is to help design, develop, and maintain the systems that process tons of requests each second, the thought of extremely efficient thread-safe containers was extremely appealing.  Of course, they also rolled out a whole parallel development framework which I won’t get into in this post but will cover bits and pieces of as time goes by. This time, I was mainly curious as to how well these new concurrent containers would perform compared to areas in our code where we manually synchronize them using lock or some other mechanism.  So I set about to run a processing test with a series of producers and consumers that would be either processing a traditional System.Collections.Generic.Queue or a System.Collection.Concurrent.ConcurrentQueue. Now, I wanted to keep the code as common as possible to make sure that the only variance was the container, so I created a test Producer and a test Consumer.  The test Producer takes an Action<string> delegate which is responsible for taking a string and placing it on whichever queue we’re testing in a thread-safe manner: 1: internal class Producer 2: { 3: public int Iterations { get; set; } 4: public Action<string> ProduceDelegate { get; set; } 5: 6: public void Produce() 7: { 8: for (int i = 0; i < Iterations; i++) 9: { 10: ProduceDelegate(“Hello”); 11: } 12: } 13: } Then likewise, I created a consumer that took a Func<string> that would read from whichever queue we’re testing and return either the string if data exists or null if not.  Then, if the item doesn’t exist, it will do a 10 ms wait before testing again.  Once all the producers are done and join the main thread, a flag will be set in each of the consumers to tell them once the queue is empty they can shut down since no other data is coming: 1: internal class Consumer 2: { 3: public Func<string> ConsumeDelegate { get; set; } 4: public bool HaltWhenEmpty { get; set; } 5: 6: public void Consume() 7: { 8: bool processing = true; 9: 10: while (processing) 11: { 12: string result = ConsumeDelegate(); 13: 14: if(result == null) 15: { 16: if (HaltWhenEmpty) 17: { 18: processing = false; 19: } 20: else 21: { 22: Thread.Sleep(TimeSpan.FromMilliseconds(10)); 23: } 24: } 25: else 26: { 27: DoWork(); // do something non-trivial so consumers lag behind a bit 28: } 29: } 30: } 31: } Okay, now that we’ve done that, we can launch threads of varying numbers using lambdas for each different method of production/consumption.  First let's look at the lambdas for a typical System.Collections.Generics.Queue with locking: 1: // lambda for putting to typical Queue with locking... 2: var productionDelegate = s => 3: { 4: lock (_mutex) 5: { 6: _mutexQueue.Enqueue(s); 7: } 8: }; 9:  10: // and lambda for typical getting from Queue with locking... 11: var consumptionDelegate = () => 12: { 13: lock (_mutex) 14: { 15: if (_mutexQueue.Count > 0) 16: { 17: return _mutexQueue.Dequeue(); 18: } 19: } 20: return null; 21: }; Nothing new or interesting here.  Just typical locks on an internal object instance.  Now let's look at using a ConcurrentQueue from the System.Collections.Concurrent library: 1: // lambda for putting to a ConcurrentQueue, notice it needs no locking! 2: var productionDelegate = s => 3: { 4: _concurrentQueue.Enqueue(s); 5: }; 6:  7: // lambda for getting from a ConcurrentQueue, once again, no locking required. 8: var consumptionDelegate = () => 9: { 10: string s; 11: return _concurrentQueue.TryDequeue(out s) ? s : null; 12: }; So I pass each of these lambdas and the number of producer and consumers threads to launch and take a look at the timing results.  Basically I’m timing from the time all threads start and begin producing/consuming to the time that all threads rejoin.  I won't bore you with the test code, basically it just launches code that creates the producers and consumers and launches them in their own threads, then waits for them all to rejoin.  The following are the timings from the start of all threads to the Join() on all threads completing.  The producers create 10,000,000 items evenly between themselves and then when all producers are done they trigger the consumers to stop once the queue is empty. These are the results in milliseconds from the ordinary Queue with locking: 1: Consumers Producers 1 2 3 Time (ms) 2: ---------- ---------- ------ ------ ------ --------- 3: 1 1 4284 5153 4226 4554.33 4: 10 10 4044 3831 5010 4295.00 5: 100 100 5497 5378 5612 5495.67 6: 1000 1000 24234 25409 27160 25601.00 And the following are the results in milliseconds from the ConcurrentQueue with no locking necessary: 1: Consumers Producers 1 2 3 Time (ms) 2: ---------- ---------- ------ ------ ------ --------- 3: 1 1 3647 3643 3718 3669.33 4: 10 10 2311 2136 2142 2196.33 5: 100 100 2480 2416 2190 2362.00 6: 1000 1000 7289 6897 7061 7082.33 Note that even though obviously 2000 threads is quite extreme, the concurrent queue actually scales really well, whereas the traditional queue with simple locking scales much more poorly. I love the new concurrent collections, they look so much simpler without littering your code with the locking logic, and they perform much better.  All in all, a great new toy to add to your arsenal of multi-threaded processing!

  Read the article

• Our Look at Opera 10.50 Web Browser

  - by Asian Angel

  Everyone has been talking about the newest version of Opera recently but perhaps you have not looked at it too closely yet. Today we will take a look at 10.50 and let you see what this “new browser” is all about. The New Engines Carakan JavaScript Engine: Runs web applications up to 7 times faster than its predecessor Futhark Vega Graphics Library: Enables super fast and smooth graphics on everything from tab switching to webpage animation Presto 2.5: Provides support for HTML5, CSS2.1 and the latest CSS3 standards A Look at the Features Available If you have installed or used older versions of Opera before then the default look after a clean install will probably seem rather different. The main differences in appearance are mainly located within the “glass border” areas of the browser. The “Speed Dial” setup looks and works just as well as in previous versions. You can set a favorite wallpaper or image as your background and choose the number of “dials” using the “Configure Speed Dial Command”. One of the “standout” differences is the “O Button”. All of the menus have been condensed into this single access point but it only takes a few moments to find what you are looking for. If you have used the style before in earlier versions of Opera some of the items have been moved around. For those who prefer the “Menu Bar” that can be easily restored using the “Show Menu Bar Command”. If desired you can actually “extend” the “Tab Bar” downwards to display thumbnails of your open tabs. Just use your mouse to grab the bottom of the “Tab Bar” and adjust it to suit your personal needs. The only problem with this feature is that it will quickly use up a good sized portion of your available UI and browser window space. The “Password Manager” is ready to access when needed…the background for the button will turn a shiny metallic blue when you open a webpage that you have “Login Information” saved for. One of the new features is a small “Recycle Bin Button” in the upper right corner. Clicking on this will display a list of recently closed tabs letting you have easy access to any tabs that you may have accidentally closed. This is definitely a great feature to have as an easy access button. For those who were used to how the “Zoom Feature” looked before it has a new “look” to it. Instead of the pop-up menu-type listing of “view sizes” present before you now have a slider button that you can use to adjust the zooming level. For our default setup here the “Sidebar Panels” available were: “Bookmarks, Widgets, Unite, Notes, Downloads, History, & Panels”. Additional panels such as “Links, Windows, Search, Info, etc.” are available if you want and/or need them (accessible using the “Panels Plus Sign Button”). The “Opera Link Button” makes it easy for you to synchronize your “Speed Dial, Bookmarks, Personal Bar, Custom Searches, History & Notes”. Note: “Opera Link” requires an account and can be signed up for using the link provided below. Want to share files with your family and friends? “Unite” allows you to do that and more. With “Unite” you can: “Stream Music, Show Photo Galleries, Share Files and/or Folders, & host webpages directly from your browser”. We have a more in-depth look at “Unite” in our article here. Note: Use of “Unite” requires an Opera account. Got a slow internet connection? “Opera Turbo” can help with that by running the web traffic through their “compression servers” to speed up your web browsing. Keep in mind that “Opera Turbo” will not engage if you are accessing a secure website (i.e. your bank’s website) thus preserving your security. Note: “Opera Turbo” can be set up to automatically detect slow internet connections (i.e. crowded Wi-Fi in a cafe). Opera has a built-in “Private Browsing Mode” now for those who prefer anonymous browsing and want to keep the “history records clean” on their computer. To access it go to “Tabs and windows” and select “New private tab” or “New private window” as desired. When you open your new “Private Tab or Window” you will see the following message with details on how Opera will handle browsing information and a large “door hanger symbol”. Notice that the one tab is locked into “Private Browsing Mode” while the others are still working in “Regular Browsing Mode”. Very nice! A miniature version of the “door hanger symbol” will be present on any tab that is locked into “Private Browsing Mode”. If you are using Windows 7 then you will love how things look from your “Taskbar”. Here you can see four very nice looking thumbnails for the tabs that we had open. All that you have to do is click on the desired thumbnail… The “Context Menu” looks just as lovely as the thumbnails and definitely has some terrific functionality built into it. Add Enhanced Aero Capability If you love “Aero” and want more for your new Opera install then we have the perfect theme for you. The theme’s name is Z1-AV69 and once you have downloaded it you will need to place it in the “Skins Subfolder” in Opera’s “Program Files Folder”. Note: For our example we used version 1.10 but version 2.00 is now available (link provided below). Once you have restarted Opera, go to the “O Menu” and select “Appearance”. When the “Appearance Window” opens click on “Z1-Glass Skin” and then click “OK”. All of a sudden you will have more “Aero Goodness” to enjoy. Compare this screenshot with the one at the top of this article…the only part that is not transparent now is the browser window area itself. Want even more “Aero Goodness”? Right click on the “Tab Bar” and set “Tab Bar Placement” to “Left”. Note: You can achieve the same effect by setting the “Tab Bar Placement” to “Right”. With the “Speed Dial” visible you will be able to see your wallpaper with ease. While this is obviously not for everyone it does make for a great visual trick. Portable Versions Perhaps you need this wonderful new version of Opera to go with you wherever you do during the day. Not a problem…just visit the Opera USB website to choose a version that works best for you. You can select from “Zip or Exe” setup files and if needed update an older portable version using a “Zipped Update Files Package”. If you are updating an older version keep in mind that you will need to delete the old “OperaUSB.exe. File” due to changes with the new setup files. During our tests updating older portable versions went well for the most part but we did experience a few “odd UI quirks” here and there…so we recommend setting up a clean install if possible. Conclusion The new 10.50 release is a pleasure to use and is a recommended install for your system. Whether you are considering trying Opera for the first time or have been using it for a bit we think that you will pleased with everything that the 10.50 release has to offer. For those who would like to add User Scripts to Opera be certain to look at our how-to article here. Links Download Opera 10.50 for your location (Windows) Get the latest Snapshot versions for Linux & Mac Sign up for an Opera Link account View In-Depth detail on Opera 10.50’s features Download the Z1-AV69 Aero Theme Download Portable Opera 10.50 Similar Articles Productive Geek Tips Set the Speed Dial as the Opera Startup PageSet Up User Scripts in Opera BrowserScan Files for Viruses Before You Download With Dr.WebTurn Your Computer into a File, Music, and Web Server with Opera UniteSet the Default Browser on Ubuntu From the Command Line TouchFreeze Alternative in AutoHotkey The Icy Undertow Desktop Windows Home Server – Backup to LAN The Clear & Clean Desktop Use This Bookmarklet to Easily Get Albums Use AutoHotkey to Assign a Hotkey to a Specific Window Latest Software Reviews Tinyhacker Random Tips Revo Uninstaller Pro Registry Mechanic 9 for Windows PC Tools Internet Security Suite 2010 PCmover Professional Make your Joomla & Drupal Sites Mobile with OSMOBI Integrate Twitter and Delicious and Make Life Easier Design Your Web Pages Using the Golden Ratio Worldwide Growth of the Internet How to Find Your Mac Address Use My TextTools to Edit and Organize Text

  Read the article

• Week in Geek: FBI Back Door in OpenBSD Edition

  - by Asian Angel

  This week we learned how to migrate bookmarks from Delicious to Diigo, fix annoying arrows, play old-school DOS games, schedule smart computer shutdowns, use breaks in Microsoft Word to better format documents, check the condition of hard-disks using Linux disk utilities, & what the Linux fstab is and how it works. Photo by Jameson42. Random Geek Links Another week with extra news link goodness to help keep you up to date. Photo by justmakeit. Report of FBI back door roils OpenBSD community Allegations that the FBI surreptitiously placed a back door into the OpenBSD operating system have alarmed the computer security community, prompting calls for an audit of the source code and claims that the charges must be a hoax. Fortinet: Job outlook improving for cybercrooks In an ironic twist in the job market, more positions will open up for developers who can write customized malware packers, people who can break CAPTCHA codes, and distributors who can spread malicious code, according to Fortinet. Enisa: Malware for smartphones is a ’serious risk’ Businesses and consumers are at risk of data breaches through smartphone use, according to the European Network and Information Security Agency. The trick with the f: Google and Microsoft web sites distribute malware Last week, Google’s DoubleClick advertising platform and Microsoft’s rad.msn.com online ad network briefly distributed malware to other web sites in the form of advertising banners. New scam tactic: Fake disk defraggers It would appear that scammers are trying out new programs to see which might best confuse potential victims and evade detection by legitimate antivirus software. Microsoft closes IE and Stuxnet holes As previously announced, Microsoft has released 17 security updates to close 40 security holes. All four Windows holes so far disclosed in connection with Stuxnet have now been closed. Microsoft Offers H.264 Support to Firefox on Windows via Add-On The new HTML5 Extension for Windows Media Player Firefox Plug-in add-on from Microsoft offers users that are running Firefox on Windows 7 H.264 support for HTML5 video playback. Google proclaims Chrome business-ready Google has announced that Chrome is ready for corporate use. Microsoft Tells Exchange Customers to Think Twice Before Opting for Google Message Continuity This week, Microsoft is telling companies still running Exchange 2010’s precursors that they should carefully consider the implications of embracing Google Message Continuity. Who Google has in mind for its Chrome OS users Steven Vaughan-Nichols explains why he feels that Chrome OS will be ideal for either office-workers or people who need a computer, but do not know the first thing about how to use one safely. Oracle takes office suite to the cloud Oracle has introduced Cloud Office 1.0, a cloud-based version of its office suite, which is aimed at web and mobile users. Mozilla pays premiums for reports of vulnerabilities The Mozilla Foundation has followed Google’s example by expanding its rewards program for reports of vulnerabilities in its Web applications. Who bought those 882 Novell patents? Not just Microsoft The mysterious CPTN Holdings — the organization that bought the 882 Novell patents as part of the terms of the Attachmate acquisition of Novell – has been unmasked (Microsoft, Apple, EMC and Oracle). Appeals court: Feds need warrants for e-mail Police must obtain search warrants before perusing Internet users’ e-mail records, a federal appeals court ruled today in a landmark decision that struck down part of a 1986 law allowing warrantless access. Geek Video of the Week What happens when someone plays a wicked prank by shoveling crazy snow paths that lead to dead ends or turn back on themselves? Watch to find out! Photo by CollegeHumor. Janitor Snow Shoveling Prank Random TinyHacker Links The Oatmeal on Cat vs Internet What lengths will our poor neglected kitty hero have to go to in order to get some attention? Guide On Using JoliCloud With Windows JoliCloud is a nifty operating system that’s made for people who need a light-weight OS that’s mostly cloud based. Check this guide on using it with Windows. Use Cameyo to Easily Create Portable Programs Here’s a nifty tool to make portable apps out of programs in Windows. Check out the guide to do it. Better Family Tech Support A nice new site by Google to help members of family understand how computers work. Track Your Stolen Mobile Phone With F-Secure A useful anti-theft tool for your mobile phone. Super User Questions Another week with great answers to popular questions from Super User. What Chrome password manager fits my requirements? What’s the best way to be able to reimage windows computers? Could you suggest feature-rich disk-based personal backup program for linux (and I’ve seen a few)? What is IPv6 and why should I care? Is there any way to find out what programs are trying to connect to Internet on windows? How-To Geek Weekly Article Recap Here are our hottest articles full of geeky goodness from this past week at HTG. 20 OS X Keyboard Shortcuts You Might Not Know Microsoft Security Essentials 2.0 Kills Viruses Dead. Download It Now. Is Your Desktop Printer More Expensive Than Printing Services? Ask the Readers: Would You Be Willing to Give Windows Up and Use a Different O.S.? The Twelve Days of Geekmas One Year Ago on How-To Geek Enjoy reading through our latest batch of retro-geek goodness from one year ago. Macrium Reflect is a Free and Easy To Use Backup Utility How To Turn a Physical Computer Into A Virtual Machine with Disk2vhd How To Restore Windows 7 from a System Image How To Manage Hard Drive Space Used by Windows 7 Backup and Restore How To Manage Hibernate Mode in Windows 7 The Geek Note That is all we have for you this week, so see you back here again after the holidays! Got a great tip? Send it in to us at [email protected]. Photo by mitjamavsar. Latest Features How-To Geek ETC The Complete List of iPad Tips, Tricks, and Tutorials The 50 Best Registry Hacks that Make Windows Better The How-To Geek Holiday Gift Guide (Geeky Stuff We Like) LCD? LED? Plasma? The How-To Geek Guide to HDTV Technology The How-To Geek Guide to Learning Photoshop, Part 8: Filters Improve Digital Photography by Calibrating Your Monitor Deathwing the Destroyer – WoW Cataclysm Dragon Wallpaper Drag2Up Lets You Drag and Drop Files to the Web With Ease The Spam Police Parts 1 and 2 – Goodbye Spammers [Videos] Snow Angels Theme for Windows 7 Exploring the Jungle Ruins Wallpaper Protect Your Privacy When Browsing with Chrome and Iron Browser

  Read the article

• Why do I have to run aptitude update twice to install Ruby?

  - by Willie Wheeler

  Summary. I have a fresh EC2 Precise 64-bit instance (ami-82fa58eb). After launching the instance, I want to install ruby1.9.1 (among others). This doesn't work: aptitude update && apt-get -o Dpkg::Options::="--force-confnew" --force-yes -fuy dist-upgrade && aptitude install -y ruby1.9.1 ruby1.9.1-dev make as Aptitude can't find the Ruby package. But this works: aptitude update && aptitude update && apt-get -o Dpkg::Options::="--force-confnew" --force-yes -fuy dist-upgrade && aptitude install -y ruby1.9.1 ruby1.9.1-dev make I would like to understand why I need to run aptitude update twice. Details. The first and second runs look pretty different. First run: Ign http://security.ubuntu.com precise-security InRelease Ign http://archive.ubuntu.com precise InRelease Get: 1 http://security.ubuntu.com precise-security Release.gpg [198 B] Ign http://archive.ubuntu.com precise-updates InRelease Get: 2 http://security.ubuntu.com precise-security Release [49.6 kB] Hit http://archive.ubuntu.com precise Release.gpg Get: 3 http://archive.ubuntu.com precise-updates Release.gpg [198 B] Hit http://archive.ubuntu.com precise Release Get: 4 http://security.ubuntu.com precise-security/main amd64 Packages [161 kB] Get: 5 http://archive.ubuntu.com precise-updates Release [49.6 kB] Get: 6 http://security.ubuntu.com precise-security/restricted amd64 Packages [3,969 B] Hit http://archive.ubuntu.com precise/main amd64 Packages Get: 7 http://security.ubuntu.com precise-security/universe amd64 Packages [43.8 kB] Hit http://archive.ubuntu.com precise/restricted amd64 Packages Hit http://archive.ubuntu.com precise/universe amd64 Packages Get: 8 http://security.ubuntu.com precise-security/multiverse amd64 Packages [2,180 B] Hit http://archive.ubuntu.com precise/multiverse amd64 Packages Get: 9 http://security.ubuntu.com precise-security/main i386 Packages [165 kB] Hit http://archive.ubuntu.com precise/main i386 Packages Hit http://archive.ubuntu.com precise/restricted i386 Packages Hit http://archive.ubuntu.com precise/universe i386 Packages Hit http://archive.ubuntu.com precise/multiverse i386 Packages Get: 10 http://security.ubuntu.com precise-security/restricted i386 Packages [3,968 B] Hit http://archive.ubuntu.com precise/main TranslationIndex Get: 11 http://security.ubuntu.com precise-security/universe i386 Packages [44.0 kB] Hit http://archive.ubuntu.com precise/multiverse TranslationIndex Get: 12 http://security.ubuntu.com precise-security/multiverse i386 Packages [2,369 B] Get: 13 http://security.ubuntu.com precise-security/main TranslationIndex [73 B] Hit http://archive.ubuntu.com precise/restricted TranslationIndex Get: 14 http://security.ubuntu.com precise-security/multiverse TranslationIndex [71 B] Hit http://archive.ubuntu.com precise/universe TranslationIndex Get: 15 http://security.ubuntu.com precise-security/restricted TranslationIndex [71 B] Get: 16 http://archive.ubuntu.com precise-updates/main amd64 Packages [382 kB] Get: 17 http://security.ubuntu.com precise-security/universe TranslationIndex [73 B] Get: 18 http://security.ubuntu.com precise-security/main Translation-en [76.5 kB] Get: 19 http://security.ubuntu.com precise-security/multiverse Translation-en [995 B] Get: 20 http://security.ubuntu.com precise-security/restricted Translation-en [978 B] Get: 21 http://security.ubuntu.com precise-security/universe Translation-en [27.2 kB] Get: 22 http://archive.ubuntu.com precise-updates/restricted amd64 Packages [6,755 B] Get: 23 http://archive.ubuntu.com precise-updates/universe amd64 Packages [129 kB] Get: 24 http://archive.ubuntu.com precise-updates/multiverse amd64 Packages [8,677 B] Get: 25 http://archive.ubuntu.com precise-updates/main i386 Packages [387 kB] Get: 26 http://archive.ubuntu.com precise-updates/restricted i386 Packages [6,732 B] Get: 27 http://archive.ubuntu.com precise-updates/universe i386 Packages [130 kB] Get: 28 http://archive.ubuntu.com precise-updates/multiverse i386 Packages [9,672 B] Get: 29 http://archive.ubuntu.com precise-updates/main TranslationIndex [3,564 B] Get: 30 http://archive.ubuntu.com precise-updates/multiverse TranslationIndex [2,605 B] Get: 31 http://archive.ubuntu.com precise-updates/restricted TranslationIndex [2,461 B] Get: 32 http://archive.ubuntu.com precise-updates/universe TranslationIndex [2,850 B] Get: 33 http://archive.ubuntu.com precise/main Translation-en [726 kB] Get: 34 http://archive.ubuntu.com precise/multiverse Translation-en [93.4 kB] Get: 35 http://archive.ubuntu.com precise/restricted Translation-en [2,395 B] Get: 36 http://archive.ubuntu.com precise/universe Translation-en [3,341 kB] Get: 37 http://archive.ubuntu.com precise-updates/main Translation-en [188 kB] Get: 38 http://archive.ubuntu.com precise-updates/multiverse Translation-en [5,414 B] Get: 39 http://archive.ubuntu.com precise-updates/restricted Translation-en [1,484 B] Get: 40 http://archive.ubuntu.com precise-updates/universe Translation-en [77.3 kB] Ign http://archive.ubuntu.com precise/main Translation-en_US Ign http://archive.ubuntu.com precise/multiverse Translation-en_US Ign http://archive.ubuntu.com precise/restricted Translation-en_US Ign http://archive.ubuntu.com precise/universe Translation-en_US Fetched 6,137 kB in 11s (538 kB/s) Reading package lists... Second run: Ign http://us-east-1.ec2.archive.ubuntu.com precise InRelease Ign http://us-east-1.ec2.archive.ubuntu.com precise-updates InRelease Get: 1 http://us-east-1.ec2.archive.ubuntu.com precise Release.gpg [198 B] Get: 2 http://us-east-1.ec2.archive.ubuntu.com precise-updates Release.gpg [198 B] Ign http://security.ubuntu.com precise-security InRelease Get: 3 http://us-east-1.ec2.archive.ubuntu.com precise Release [49.6 kB] Get: 4 http://us-east-1.ec2.archive.ubuntu.com precise-updates Release [49.6 kB] Get: 5 http://us-east-1.ec2.archive.ubuntu.com precise/main Sources [934 kB] Hit http://security.ubuntu.com precise-security Release.gpg Hit http://security.ubuntu.com precise-security Release Get: 6 http://us-east-1.ec2.archive.ubuntu.com precise/universe Sources [5,019 kB] Get: 7 http://security.ubuntu.com precise-security/main Sources [42.8 kB] Get: 8 http://security.ubuntu.com precise-security/universe Sources [13.5 kB] Hit http://security.ubuntu.com precise-security/main amd64 Packages Hit http://security.ubuntu.com precise-security/universe amd64 Packages Hit http://security.ubuntu.com precise-security/main i386 Packages Get: 9 http://us-east-1.ec2.archive.ubuntu.com precise/main amd64 Packages [1,273 kB] Hit http://security.ubuntu.com precise-security/universe i386 Packages Get: 10 http://us-east-1.ec2.archive.ubuntu.com precise/universe amd64 Packages [4,786 kB] Hit http://security.ubuntu.com precise-security/main TranslationIndex Hit http://security.ubuntu.com precise-security/universe TranslationIndex Hit http://security.ubuntu.com precise-security/main Translation-en Hit http://security.ubuntu.com precise-security/universe Translation-en Get: 11 http://us-east-1.ec2.archive.ubuntu.com precise/main i386 Packages [1,274 kB] Get: 12 http://us-east-1.ec2.archive.ubuntu.com precise/universe i386 Packages [4,796 kB] Get: 13 http://us-east-1.ec2.archive.ubuntu.com precise/main TranslationIndex [3,706 B] Get: 14 http://us-east-1.ec2.archive.ubuntu.com precise/universe TranslationIndex [2,922 B] Get: 15 http://us-east-1.ec2.archive.ubuntu.com precise-updates/main Sources [163 kB] Get: 16 http://us-east-1.ec2.archive.ubuntu.com precise-updates/universe Sources [50.8 kB] Get: 17 http://us-east-1.ec2.archive.ubuntu.com precise-updates/main amd64 Packages [382 kB] Get: 18 http://us-east-1.ec2.archive.ubuntu.com precise-updates/universe amd64 Packages [129 kB] Get: 19 http://us-east-1.ec2.archive.ubuntu.com precise-updates/main i386 Packages [387 kB] Get: 20 http://us-east-1.ec2.archive.ubuntu.com precise-updates/universe i386 Packages [129 kB] Get: 21 http://us-east-1.ec2.archive.ubuntu.com precise-updates/main TranslationIndex [3,564 B] Get: 22 http://us-east-1.ec2.archive.ubuntu.com precise-updates/universe TranslationIndex [2,850 B] Get: 23 http://us-east-1.ec2.archive.ubuntu.com precise/main Translation-en [726 kB] Get: 24 http://us-east-1.ec2.archive.ubuntu.com precise/universe Translation-en [3,341 kB] Get: 25 http://us-east-1.ec2.archive.ubuntu.com precise-updates/main Translation-en [188 kB] Get: 26 http://us-east-1.ec2.archive.ubuntu.com precise-updates/universe Translation-en [77.1 kB] Fetched 23.8 MB in 23s (1,026 kB/s) Reading package lists... Note. My question is almost exactly the same as Running 'apt-get upgrade' on Amazon EC2 AMI twice in succession upgrades very different packages except that I'm seeing this issue with aptitude updates rather than apt-get upgrades.

  Read the article

< Previous Page | 218 219 220 221 222 223 224 225 226 227 228 229  | Next Page >