Search Results

Search found 8950 results on 358 pages for 'eee pc 1000he'.

Page 231/358 | < Previous Page | 227 228 229 230 231 232 233 234 235 236 237 238  | Next Page >

  • How to use Ralink RT2501/RT2573 as wifi access point in Debian Linux

    - by user60813
    Hi, I have a fit-PC server with Debian GNU/Linux (Lenny). I would like to use it as a wifi access point since my Linksys WRT54GS has become unstable. I have a USB Ralink wifi NIC. When I insert the card to USB I can see this with lsusb: Bus 001 Device 002: ID 148f:2573 Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter I have tried following various HOWTOs on using wifi card as AP in Linux, however, it seems that the card cannot go into monitor mode. I believe this is because I must use a newer driver or upload non-free firmware or something like that. I have tried installed wicd, but it does not help. I bought this wifi adapter because I was told that it is one of the most common used Linux supported wifi cards that can be used as access point and a lot of other stuff. So my question is: How do I set up this USB wifi card as wireless access point in Debian Lenny?

    Read the article

  • How to tell Windows 7 to ignore a default gateway

    - by zildjohn01
    I currently have 2 network cards in my PC -- one connected to an internal network on a router with a disconnected WAN port (10.x.x.x), and one connected to the internet through a consumer router (192.168.0.x). Windows seems to recognize them correctly (my "Network and Sharing Center" lists them as "No Internet" and "Internet" respectively), however when I try browsing the internet it always tries the internal network's default gateway, rather than the one with internet access. Trying to ping a website results in "Reply from 10.0.0.1: Destination net unreachable.". A simple "route delete 0.0.0.0 mask 0.0.0.0 10.0.0.1" fixes the problems, but they return upon reboot, or upon renewing my IP. Is there any way to tell Windows to ignore one NIC's default gateway, or to at least give them priorities?

    Read the article

  • Wake timers don't wake computer from sleep mode

    - by Joe
    I'm got a custom built PC running 64 bit Windows 7 Ultimate. So far everything works great except for one thing: it will not wake up from sleep mode for a wake timer or scheduled task. Sleep mode itself works great. If it's sleeping, it wakes successfully when I press the power button, mash the keyboard, wiggle the mouse, or send a WOL packet. The only problem is wake timers. I even tried the program WakeupOnStandBy but it looks like that uses wake timers, so it doesn't do anything for me either. And yes, wake timers are enabled: Any ideas on how to fix the problem, or troubleshoot it? I'd imagine that there would be a log somewhere telling me exactly why the wake timers are having trouble, but if there is I haven't found it.

    Read the article

  • How to disable Windows 8 lock screen?

    - by Filip
    So I took a plunge and installed Windows 8 Consumer Preview on my main home PC. So far so good, but there is one annoyance - the system "locks" the computer after a period of inactivity causing me to re-enter my password. I really would like to avoid this, but have no idea how. I already tried the power settings (no pass on wake up) and the screen saver settings with no luck. Is this some sort of bug, or am I missing something? P.S. In this case I favor convenience over security.

    Read the article

  • how to test lan network speed with ps3

    - by Damon
    I am having a heck of a time trying to get videos streaming to my PS3. I want to know if there is some way to test the speed between my PC and ps3 to see if that is the issue. For some reason when things get really slow between the ps3 and my computer (it's a wired connection through a switch), the wireless internet on completely different computer gets slow. I don't know what's causing what, but I don't know why there should be any correlation between internet speed on a wirelessly connected laptop and the LAN speed between a wired ps3 and computer.

    Read the article

  • How to troubleshoot a service failure?

    - by AngryHacker
    I get a GPF dialog box out of the blue fairly often (like about 2 hours after I turn on the computer). It basically says that svchost.exe had a failure... (see the corresponding Event Log entry below). Event Type: Error Event Source: Application Error Event Category: (100) Event ID: 1000 Date: 5/18/2010 Time: 7:41:16 PM User: N/A Computer: DKHA-IPSA Description: Faulting application svchost.exe, version 5.1.2600.5512, faulting module ole32.dll, version 5.1.2600.5512, fault address 0x0004eaa9. Shortly after this error pops up, the computer pretty much grinds to a halt (e.g. some UI elements on the desktop simply do not respond). And I have to do a hard reboot. How do I troubleshoot this type of thing? P.S. The PC has all the latest patches and nothing is missing in the Device Manager.

    Read the article

  • Bind: dns not 'spreaded'

    - by realtebo
    I've elfoip.net with bind $ whois elfoip.net | grep 'Name Server' Name Server: NS.ELFOIP.NET I need elfoip.net be able to serve third levels domain, like mickymouse.elfoip.net, etc... Yes, I'm trying to create an other useless dyndns clone. i've added some third level as A RR. Eg: executing this from the server itself $ dig @localhost mattinauno.elfoip.net ;; ANSWER SECTION: mattinauno.elfoip.net. 60 IN A 192.81.221.113 I was expecting in one or two days, from my pc i can digit in browser mattinauno.elfoip.net and get page a 192.81.221.113 But this is not happening. Are there any prerequisites to satisfy to allow dns of my isp to be able to forward dns resolution of *.elfoip.net to MY dns ? (Or to ask to him and then cache ?) TTL of zone is set a 5m I've not AllowQuey directive, is it necessary for other dns to cache from mine ? I've cheched the zone with bind utility named-checkzone but no error detected. How to diagnose why other dns doesn't take in account RR from mine ? from my home pc dig @ns.elfoip.net mattinauno.elfoip.net ;; ANSWER SECTION: mattinauno.elfoip.net. 60 IN A 192.81.221.113 ;; AUTHORITY SECTION: elfoip.net. 300 IN NS ns.elfoip.net. but dig @8.8.8.8 mattinauno.elfoip.net give no answers Whole zone file: note I've used nsupdate, so this file has been re-edited and re-formatted from this utility ! root@mirko:/var/named# cat elfoip.net.db $ORIGIN . $TTL 300 ; 5 minutes elfoip.net IN SOA ns.elfoip.net. hostmaster.elfoip.net. ( 2013062314 ; serial 3600 ; refresh (1 hour) 600 ; retry (10 minutes) 86400 ; expire (1 day) 60 ; minimum (1 minute) ) NS ns.elfoip.net. A 109.168.99.6 $ORIGIN elfoip.net. $TTL 60 ; 1 minute google A 173.194.35.56 maiscai A 192.81.221.113 mattinadue A 192.81.221.113 mattinauno A 192.81.221.113 $TTL 300 ; 5 minutes ns A 109.168.99.6 $TTL 60 ; 1 minute prova A 208.67.222.222 prova2 A 13.23.34.45 A 13.23.34.46 www CNAME elfoip.net. EDIT: added named.conf.local zone "elfoip.net" { type master; // file "/etc/bind/elfoip.net.db"; file "/var/named/elfoip.net.db"; allow-update { key elfoip.net ; }; }; EDIT: I've no setup list-on directive *EDIT Added a TCPDUMP after [email protected] wwww.elfoip.net from a machine which uses my company internal dns, who allow recursive query. root@mirko:~# tcpdump -i eth0 'port 53' tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 11:57:23.293611 IP host9-210-static.22-87-b.business.telecomitalia.it.45958 > mirko.elfoip.net.domain: 61337+ A? www.elfoip.net. (32) 11:57:23.294114 IP mirko.elfoip.net.domain > host9-210-static.22-87-b.business.telecomitalia.it.45958: 61337* 2/1/1 CNAME elfoip.net., A 109.168.99.6 (95) 11:57:23.294554 IP mirko.elfoip.net.59571 > google-public-dns-a.google.com.domain: 45851+ PTR? 9.210.22.87.in-addr.arpa. (42) 11:57:23.330444 IP google-public-dns-a.google.com.domain > mirko.elfoip.net.59571: 45851 1/0/0 PTR host9-210-static.22-87-b.business.telecomitalia.it. (106) 11:57:23.331181 IP mirko.elfoip.net.44171 > google-public-dns-a.google.com.domain: 33339+ PTR? 8.8.8.8.in-addr.arpa. (38) 11:57:23.439405 IP google-public-dns-a.google.com.domain > mirko.elfoip.net.44171: 33339 1/0/0 PTR google-public-dns-a.google.com. (82) 11:57:31.350654 IP host9-210-static.22-87-b.business.telecomitalia.it.30108 > mirko.elfoip.net.domain: 38269 [1au] A? ns.elfoip.net. (42) 11:57:31.351117 IP mirko.elfoip.net.domain > host9-210-static.22-87-b.business.telecomitalia.it.30108: 38269* 1/1/1 A 109.168.99.6 (72) If i dig @8.8.8.8 www.elfoip.net, NOTHING happens in dump log !

    Read the article

  • Cannot install Windows 8 Transformation Pack on Windows 7

    - by Mehper C. Palavuzlar
    I am trying to install Windows 8 Transformation Pack v4.0 on my Sony Vaio laptop with the following options: When I run (as administrator) the setup file, it starts to install but gives the following error at some point: The file 'C:\Windows\Fonts\segoui.ttf' could not be opened. Please check that your disk is not full and that you have access to the destination directory. Since I run the installer as administrator, this error message seems strange to me. Segoe UI font is also installed on my PC. When I try to install with default system fonts (without Segoe UI), it gives the same error again: What should I do to solve this problem?

    Read the article

  • System Center Configuration Manager 2007 - Debugging Client Installs

    - by Dayton Brown
    Hi All: Having an issue installing the CCMsetup client on desktops. The CCMSetup makes it to the PC, files are there, it gets added to the services for automatic start, it starts, but quits almost instantly. Logs on the desktop show a entry like this. <![LOG[Failed to successfully complete HTTP request. (StatusCode at WinHttpQueryHeaders: 404)]LOG]!><time="14:28:51.183+240" date="06-11-2009" component="ccmsetup" context="" type="3" thread="2388" file="ccmsetup.cpp:5808"> What am I missing? EDIT: Firewall is off on both client and server.

    Read the article

  • Port Forwarding: Why do my local sites on 80 work but not those on 8080?

    - by Chadworthington
    I setup my router to forward port 80 to the PC hosting my web site. As a result, I am able to access this url (Don't bother clicking on it, it's just an example): http://my.url.com/ When i click on this link, it works: http://localhost:8080/tfs/web/ I also forward port 8080 to the same web server box But when I try to access this url I get the eror "Page Cannot be displayed:" http://my.url.com:8080/tfs/web/ I fwded port 8080 the same way I fwded port 80. I also turned off Windows Firewall, in case it was blocking port 8080. Any theories why port 80 works but 8080 does not?

    Read the article

  • how to create iso dvd image for use with mac/osx "Disk Utility"?

    - by adolf garlic
    This seemed way easier on my pc. I would just pop a blank dvd in the drive, it asked what I wanted to do with it, to which I would respond, "burn dvd with nero" (paraphrasing), then I would pick "new" and just drag and drop the folders in there. Mac appears to have "Disk Utility" which just requires that I 'choose an image' but then doesn't bother to detail - how to do this - what the options mean e.g. format "mac OS extended (journaled)" is that ever going to be readable on a non mac machine? I want to create an ISO standard dvd as per the 'default' you'd get on nero. All the stuff on the web points to doing things with 'terminal' (the whole point of buying a mac was to get away from command line jiggery pokery - I'm trying to burn some photos not land a friggin lunar module here!) Please, if you can just provide some simple instructions on what I need to achive this I'd be extremely grateful. Ta muchley in advance.

    Read the article

  • virtual machines

    - by André Alçada Padez
    well, i hope this doesn't get categorized as a boating question, but it really is related to programming. I have windows XP, and i am going to have to have a VM running: Windows 7 Visual Studio 2008 Sql Server 2008 IIS 7 (8 in a little while) Wamp Photoshop CS5 etc... so i was wondering what should i use to be easier to install and configure, and best performance: Virtual Box or Microsoft's Virtual Machine? Thank you Well i tried Virtual Box, it's always crashing for some reason. I think i'm going to try Virtual PC, just to stick to an all Microsoft Solution.

    Read the article

  • How can you test communication on a COM/Serial port?

    - by Andy
    We have a OHAUAS Weighting scales with a COM port. if we connect this to a PC we should be able to get the weight on the computer by sending a command to it. Is there a way to test this? i tried the command line echo "LP" com1 but this does nothing. A small C# application that listens to this port seems to be continuously receive Hexadecimal numbers (2 digits then an enter), however sending a command through this application doesn't give readable results. When i do listen on the port though, the echo "LP" com1 command gives an unavaible error, so sending the command works in cmd. Does anyone have any knowledge on a simple way to test a send and receive on a com port?

    Read the article

  • What is the best way to setup a public and private wireless access point on the same home network?

    - by Dougman
    For my home network (with internet provided from a cable modem) I would like to setup a secure wireless access point that I use for all of my personal connections (home PC, iPhone, Xbox, etc) and also another public access point that friends and folks in the neighborhood may connect to (for good karma). I want to ensure that my private traffic cannot be accessed from users of the public access point. I currently have one router that is running the Tomato firmware that I use with WPA security. What is the best way to accomplish this kind of setup securely (if it is possible in a home environment)?

    Read the article

  • Synaptics/usb mouse drivers data is invalid on win server 2003

    - by the wonderer
    Have just installed windows server 2003 image onto an HP laptop. Cannot get the mouse drivers to work. Have the correct drivers because I've extracted them out of a working PC (exact same model). I am always getting "Data is invalid". This is the synaptics touchpad drivers. Does anyone know how to fix this/ workaround to get mouse working? I have heard it may have something to do with permissions in the registry?

    Read the article

  • RAID0 PROBLEM WITH A SONY SPORTING A NEW HDD

    - by redrock
    Sony Windows 7 PC. Originally had 2 x 300Gb HDD. One HDD completely pancaked so have replaced with a new 500Gb HDD. When both drives are connected the 300GB doesn't appear to be recognised as a 300Gb HDD as a seperate entity. BIOS sees it but the operating system only sees a total of 465GB of HD space. When both disks are attached unde disk management it shows one 465Gb as RAID 0 and the new drive as STxxxxxx 465Gb. My question I guess is what should I see in total HDD space and is this configured correctly as I thought I would see 2 seperate drives 1x500Gb and 1x300Gb. My customer insisted that prior to the HDD crash he saw 2 drives both registering as 300Gb (a c: and d: drive).

    Read the article

  • Dovecot ignoring maximum number of IMAP connections

    - by Michelle
    I have a single mailbox mail server running Dovecot/Postfix and I have two IMAP clients, Thunderbird on the PC and K9 on Android. I keep on receiving this error in my logs even after I change the 'mail_max_userip_connections' variable to 50. puppet dovecot: imap-login: Maximum number of connections from user+IP exceeded (mail_max_userip_connections=10): user=<[email protected]>, method=PLAIN, rip=62.242.90.2, lip=198.29.31.229, TLS Why does it say that it is set to 10 in the log? Is that hardcoded? grep -r "mail_max_userip_connections" /etc/dovecot /etc/dovecot/conf.d/20-managesieve.conf: #mail_max_userip_connections = 10 /etc/dovecot/conf.d/20-pop3.conf: #mail_max_userip_connections = 3 /etc/dovecot/conf.d/20-imap.conf: mail_max_userip_connections = 50 I've restarted dovecot after making the changes but this error is still logged and I can't access the mailbox. Can anyone help me understand why I can't seem to raise the maximum limit?

    Read the article

  • IP Camera working on lan but not on internet

    - by Kevin Boyd
    My IP cam model is Genius 350TR, I tested the cam at home on lan and internet and it worked. Then I shifted it to an office. It works on the office lan setup but I cannot connect to the ip cam from home. The IP cam is configured for port 192.168.0.30:7070 and it has a port forwarded to publicIP:7071 When I telnet to that public IP it connects to that port. However when I try to access the ip cam from a web browser it only shows me the configuration page and settings and the video is blank and it says connecting for some time and then says disconnected. The cam is configured for HTTP on internet and UDP on Lan. The office setup is ISP --- WifiRouter --- PC With Wifi card --- Switch --- IP CAM Is there a way to debug this problem?

    Read the article

  • Audigy 2 Coaxial to Coaxial/Optical connection possible?

    - by Chris
    Hello, The original question is deleted, and asked again below with accurate information. Edit: Excuse me for my ignorance, my friend has a Logitech Z-5500 set. I thought after comparing those systems on Google images that he had the Z-680, but he hasn't. This set has a single Digital coaxial for DVD or CD players or PC sound cards (requires coaxial cable, sold separately) cable. This single cable was connected to the orange tulip connector (SPDIF coaxial out) on the backside of his onboard HP Elite m9070, this connector is broken. How can I use the digital out with a single cable coaxial cable on the Audigy2 (see image below) (I have the following converters for my disposal, can I use one of these? 3.5 mm male - coax optical mini optical male - toslink optical female 2 x toslink optical female, toslink coupler, optical audio extension note: Is it possible to connect a toslink cable with an mini optical male - toslink converter on the digital out of the Audigy 2? (see image below)

    Read the article

  • Tomcat 6.0 service does not start: java/lang/NoClassDefFoundError

    - by James Lawruk
    I installed Tomcat on my Windows XP PC. But I can't get it to start. I start the service and I see the progress bar, but it fails. I installed the Java Runtime Environment Version 6 and created JRE_HOME Environment variable. (C:\Program Files\Java\jre6) Any ideas? Thanks. Below is the jakarta_serviceYYYMMDD.log entries: [2010-04-08 14:22:42] [info] Commons Daemon procrun (1.0.2.0) started [2010-04-08 14:22:42] [info] Running Service... [2010-04-08 14:22:42] [info] Starting service... [2010-04-08 14:22:42] [info] Error occurred during initialization of VM [2010-04-08 14:22:42] [info] java/lang/NoClassDefFoundError [2010-04-08 14:22:42] [info] : java/lang/Object

    Read the article

  • Setup Windows Media Player 11 to stream from TVersity

    - by snorfys
    I've got TVersity installed on a Windows 2003 server box (work had an extra license that they donated to let me install at home to get some practice setting up/administering a domain etc.) I found out that Windows Media Player 11 won't install on Windows 2003, but installed TVersity instead and streaming to my 360 is working great. Problem is that I don't know how to setup streaming to any other PC on the network. All of the PCs have access to the shared network folder, but playing from there doesn't stream and the stutter is pretty bad. Is there a way to setup Windows Media Player 11 or another player to stream from TVersity?

    Read the article

  • Setup dhcpd without gateway on purpose

    - by MBober
    I have an XP machine with two network interfaces. One is connected to my company's network (and the Internet). The other is a very local network which connects some hardware with my PC. Both the hardware and my XP machine's second network interface obtain configuration from a dhcpd running on Ubuntu in a virtual machine on my XP machine. I entered some dummy gateway in /etc/dhcp3/dhcpd.conf like 192.168.3.1 which does not match any existing device just to get dhcpd started. The problem is that my XP machine now tries to route Internet traffic through 192.168.3.1 in most of the cases which, of course, results in an error. Is there any way to set up dhcpd in a way that the clients know that there is no gateway in this network? By the way: setting the gateway manually in XP is off the table because this needs administrator privileges which I don't have.

    Read the article

  • Can't communicate using PuTTY, but can with Termite

    - by SharpHawk
    I'm trying to establish a serial connection to a peripheral from my PC's RS-232 port. Pretty simple stuff, and I've had not trouble doing it with countless peripherals before. And yet when I configure PuTTY to the right baud rate, stop bits, etc. I'll type in "*IDN?", press enter, and the unit won't reply. After going over my settings over and over again, I decided to try another terminal program, Termite. This time it worked like a charm. What puzzles me, and what I'm trying to figure out by posting this question, is why Termite would work when PuTTY did not despite the fact that they both have the same settings. PuTTY: http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Termite: http://www.compuphase.com/software_termite.htm EDIT: I now tried Tera Term as well, and it works. So PuTTY is the odd one out.

    Read the article

  • Why does my DNS change (and break) at regular intervals?

    - by Peter Kelly
    I have a laptop running Windows 7. Up until recently, everything was fine. We have multiple devices in my house connecting to the one access point with no problems. No issues with ISP. Now my Windows 7 PC DNS settings change every minute or so. Before the problem occurs if I do an ipconfig /all I have two DNS settings (primary/secondary) and everything is fine. After a short period of time this change to a sole DNS, 10.0.0.1. Webpages no longer resolve. If I do an ipconfig /renew, this fixes the problem. I have tried uninstalling various programs I thought might be related but the problem persists. Any ideas of potential causes?

    Read the article

  • What files should be excluded from a complete Windows backup?

    - by tro
    I'm starting to use CrashPlan to backup my Win 7 PC. I've got it writing to my external HD (for quick local restores) and to CrashPlan Central (for offsite storage). I'd like to backup my entire C:\ drive (the only partition) in a way that: Preserves all of my installed software and configuration, but Avoids backing up log files and other ephemeral / temporary files that are regenerated during normal operation of the OS. Which files and/or directories should I be excluding from backups? I'd like to make this a community wiki, so that we could all contribute towards a definitive list. Here's a list of regular expressions identifying the directories and files that CrashPlan excludes on Windows by default listed at http://support.crashplan.com/doku.php/articles/admin_excludes: .*/(?:42|\d{8,})/(?:cp|~).* (?i).*/CrashPlan.*/(?:cache|log|conf|manifest|upgrade)/.* .*\.part .*/iPhoto Library/iPod Photo Cache/.* .*\.cprestoretmp.* *\.rbf :/Config\\.Msi.* .*/Google/Chrome/.*cache.* .*/Mozilla/Firefox/.*cache.* .*\$RECYCLE\.BIN/.* .*/System Volume Information/.* .*/RECYCLER/.* .*/I386.* .*/pagefile.sys .*/MSOCache.* .*UsrClass\.dat\.LOG .*UsrClass\.dat .*/Temporary Internet Files/.* (?i).*/ntuser.dat.* .*/Local Settings/Temp.* .*/AppData/Local/Temp.* .*/AppData/Temp.* .*/Windows/Temp.* (?i).*/Microsoft.*/Windows/.*\.log .*/Microsoft.*/Windows/Cookies.* .*/Microsoft.*/RecoveryStore.* (?i).:/Config\\.Msi.* (?i).*\\.rbf .*/Windows/Installer.* Other excludes: .*\.(class|obj) .*/hiberfil.sys (?i).*\.tmp (?i).*/temp/ (?i).*/tmp/ .*Thumbs\.db .*/Local Settings/History/ .*/NetHood/ .*/PrintHood/ .*/Cookies/ .*/Recent/ .*/SendTo/

    Read the article

< Previous Page | 227 228 229 230 231 232 233 234 235 236 237 238  | Next Page >