Search Results

Search found 12089 results on 484 pages for 'rule of three'.

Page 353/484 | < Previous Page | 349 350 351 352 353 354 355 356 357 358 359 360  | Next Page >

• Exchange Server 2010: move mailboxes from recoveded and mounted edb to user’s mailbox

  - by user36090

  One of our exchange servers crashed, and I am trying to recover the mailboxes. We had 1 exchange 2003 server named "apex" and 1 exchange 2010 server named "2008Enterprise. the exchange 2010 server named "2008Enterprise" crashed. I created a new exchange 2010 server named "Providence". I ran the command on Providence: New-MailboxDatabase -Recovery -Name JBCMail -Server Providence -EdbFilePath "c:\data\Exchange\Mailbox\Mailbox Database 0579285147\Mailbox Database 0579285147.edb" -LogFolderPath "c:\data\Exchange\Mailbox\Mailbox Database 0579285147" this command executed and finished without error I then ran the command: eseutil /p E00 this command was executed from the below directory: c:\data\Exchange\Mailbox\Mailbox Database 0579285147 I then mounted the JBCMail with the mount command note: I do not have my full typed command. Inside my Exchange Management Console (EMC) I can view the new mailbox database named JBCMail. The JBCMail database is show as mounted on the exchange server named Providence. I can see the crashed Exchange server named 2008Exchange. In the EMC the crashed exchange server states the Copy Status under ServerConfiguration-Mailbox is ServiceDown. From here I need to recover three mailboxes The mail boxes are on the apex server. How do I move the mailboxs from apex to Providence? How do I restore the mailboxes from JBCmail mounted database to the user's mailbox? I do not fully understand how to use the Restore-Mailbox command because when I use this command it tries to restore the mailbox to the dead apex server. Restore-Mailbox -ID 'Jason Young' -RecoveryDatabase JBCMail

  Read the article

• big speed difference on a network link with and without VPN tunnel

  - by xirtyllo

  Scenario: We have a network link between two offices. The link is provided by a third party company through a VLAN on their network, but to us it is totally transparent -as if we had a simple ethernet cable going from one location to the other-. We have one router at each side of the link, with 3 VPN tunnels in between the two. The test: When I test the speed of the network link with the routers in place, with one laptop directly connected to the router on each side, I consistently get ~30/35Mbps. But if I take out the routers and I test the link connecting the laptops directly to the ethernet cable at each side, I consistently get ~85/88Mbps. It's quite a big performance hit, and I would tend to think that the VPN tunnels are responsible for the slow down. Is it normal that this configuration (two routers with three VPN tunnels between them) takes away so much bandwidth? More info: The encryption algorithm used for the VPN tunnels is AES128. The routers model is Zyxel USG200 and Zyxel USG1000, and their CPU, memory, and storage use is well within normal limits. The nominal bandwidth of the network link is 100Mbps. The network link in question is supplied by a third party company (the building in between our two offices). Basically it passes through their network as a VLAN, but the VLAN is completely transparent to us (e.g. no configuration required on our side, just like one single cable from end to end). Unfortunately (or maybe fortunately) I cannot directly test different routers configurations as I'm not the person in charge of it.

  Read the article

• Setting up ProxyPass for a Virtualmin virtual server

  - by Andy Ibanez

  I am trying to set up my web server so that I can server multiple Ghost.org blogs. I am stuck in one crucial step. To be honest, my knowledge in servers is not so big, so I request your help to do this. Basically, a tutorial I'm reading suggests I set up a VirtualHost in this way: NameVirtualHost *:80 <VirtualHost *:80> ServerName your-url.com ServerAlias www.your-url.com ProxyRequests off ProxyPass / http://127.0.0.1:2368/ ProxyPassReverse / http:/127.0.0.1:2368/ </VirtualHost> So I have gone to the Virtual site on Virtualmin to try to add everything as is. Services Configure Website Edit Directives The problem is, the previous page (Services Configure website) says I can't edit the port: This Apache virtual host belongs to the Virtualmin server linguist.andyibanez.com, so the address, port, base directory and hostname cannot be changed here. And whenever I try to add the ProxyRequests off (the other two can be added fine) directive in Edit Directives manually, I'm simply told that the directive can't be there. So what is the right way to "add" the last three directives in the VirtualHost above to my sub server? Maybe I'm missing a menu item that will help me with this? I request your help as I have looked for a while, Google keeps thinking I want to serve Webmin via Apache when I google "Set up Virtualmin proxypass", and I have no clue what to do.

  Read the article

• Bringing people into an Asterisk conference call

  - by Harley

  I'm using Asterisk 1.4 and am trying to work out a way to bring people into a conference call. In the ideal scenario two people would be talking and one of them would push some keys, then a phone number and then the three of them would be in a conference. From there they should be able to bring in other people as well. This seems to be what the Asterisk n-way call HOWTO is trying to do, but it doesn't work quite properly for me. Here's what happens: 1. Internal person A calls person B 2. Person A presses *0, he is given a dial tone and person B is taken to a conference room 3. Person A calls person C and they can talk, and then person A presses **. 4. Person C is brought to the conference room, but person A is disconnected. In the last step, A should be taken to the conference room as well. Here's the relevant logs, where 230 is person A, 231 is person B, 207 is person C, and 282 is the conference room.

  Read the article

• RPCSS kerberos issues on imaged Windows workstations

  - by sysadmin1138

  While doing some unrelated troubleshooting I came across a set of Event Log entries that have me concerned. Machine Name: labcomputer82 Source: Security-Kerberos Event ID: 4 Event Description: The Kerberos client received a KRB_AP_ERR_MODIFIED error from the server labcomputer143$. The target name used was RPCSS/imagemaster4.ad.domain.edu. This indicates that the target server failed to decrypt the ticket provided by the client. This can occur when the target server principal name (SPN) is registered on an account other than the account the target service is using. Please ensure that the target SPN is registered on, and only registered on, the account used by the server. This error can also happen when the target service is using a different password for the target service account than what the Kerberos Key Distribution Center (KDC) has for the target service account. Please ensure that the service on the server and the KDC are both updated to use the current password. If the server name is not fully qualified, and the target domain (AD.DOMAIN.EDU) is different from the client domain (AD.DOMAIN.EDU), check if there are identically named server accounts in these two domains, or use the fully-qualified name to identify the server. There are three machine names used in this message. It's generated on labcomputer82, it's attempting to talk to another lab workstation called labcomputer143, and the service in question (RPCSS) refers to the name of the machine that this machine was imaged from (and possibly also that of labcomputer143, I'm not sure). The thing that has me raising both eyebrows is that the machine named labcomputer82 is attempting to use an SPN of RPCSS/imagemaster4.ad.domain.edu. The SPN attribute on the computer object in AD looks just fine. It has all the names it should have. Of the over 3,000 computer objects in our AD domain, somewhere around 1,700 of the are computer-lab seats that are frequently imaged. If we're doing something wrong, I'd like to know in time to get our procedures modified (and people retrained) for fall quarter. But if this is normal for imaged machines, I'll just continue ignoring these.

  Read the article

• Getting AWStats to work in Ubuntu 12.04

  - by koogee

  I'm new to apache and i'm trying to set up AWStats on my ubuntu 12.04 server. I've followed the guide at Ubuntu docs https://help.ubuntu.com/community/AWStats I set it up according to the instructions and awstats is able to generate initial stats from apache log successfully. I placed the links to awstats in the default virtual host file. However when I try to run http://server-ip-address:8080/awstats/awstats.pl, I get: Error: SiteDomain parameter not defined in your config/domain file. You must edit it for using this version of AWStats. Setup ('/etc/awstats/awstats.conf' file, web server or permissions) may be wrong. Check config file, permissions and AWStats documentation (in 'docs' directory). Here is my /etc/apache2/sites-available/default file: <VirtualHost *:8080> ServerAdmin webmaster@localhost DocumentRoot /home/saad/www <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /home/saad/www/> Options Indexes FollowSymLinks MultiViews AllowOverride AuthConfig Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> Alias /awstatsclasses "/usr/share/awstats/lib/" Alias /awstats-icon "/usr/share/awstats/icon/" Alias /awstatscss "/usr/share/doc/awstats/examples/css" ScriptAlias /awstats/ /usr/lib/cgi-bin/ Options ExecCGI -MultiViews +SymLinksIfOwnerMatch ErrorLog ${APACHE_LOG_DIR}/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> The only three variables I edited in /etc/awstats/awstats.conf are: LogFile="/var/log/apache2/access.log" SiteDomain="server-name.noip.org" HostAliases="localhost 127.0.0.1 server-name.no-ip.org" The apache server works fine and i'm able to access other pages stored on the server. Any guidance would be welcome.

  Read the article

• iPod touch has extremely slow wifi, drops packets - only on my router

  - by mskfisher

  I just purchased an iPod Touch. I am having a lot of trouble with its speeds on my Tenda W311R, but it has no speed problems on my neighbor's Netgear router. It will connect and authenticate to my network, but the Speed Test app from speedtest.net shows rates near 20-50 kbps. If I run the speed test immediately after powering the iPod on, it will get speeds of 10-20 Mbps, like it should - but the speeds slow down to the kbps range abut 10-15 seconds afterward. I get the same behavior with encryption and without encryption, and regardless of N, G, or B compatibility settings in the router. I've tried rebooting the iPod and resetting the network settings, but it's still slow. I've tried pinging the iPod from another computer, and it shows about 40% packet loss: $ ping 192.168.0.111 PING 192.168.0.111 (192.168.0.111): 56 data bytes 64 bytes from 192.168.0.111: icmp_seq=0 ttl=64 time=14.188 ms 64 bytes from 192.168.0.111: icmp_seq=1 ttl=64 time=11.556 ms 64 bytes from 192.168.0.111: icmp_seq=2 ttl=64 time=5.675 ms 64 bytes from 192.168.0.111: icmp_seq=3 ttl=64 time=5.721 ms Request timeout for icmp_seq 4 64 bytes from 192.168.0.111: icmp_seq=5 ttl=64 time=6.491 ms Request timeout for icmp_seq 6 64 bytes from 192.168.0.111: icmp_seq=7 ttl=64 time=8.065 ms Request timeout for icmp_seq 8 Request timeout for icmp_seq 9 Request timeout for icmp_seq 10 64 bytes from 192.168.0.111: icmp_seq=11 ttl=64 time=9.605 ms Signal strength is good - I'm never more than 20 feet from my access point, and it exhibits the same behavior if I'm standing next to the router. It works just well enough to receive text, but videos don't work at all. App downloads are hit and miss. I've tweaked just about all of the settings I can see to tweak, and I'm at a loss. I have also been searching Google for the past three days, all to no avail. Any suggestions?

  Read the article

• How do I force Windows 7 to recognize my Projector?

  - by user63564

  I have a new Dell XPS with an NVIDIA GeForce GT 445M and an old (several years) Epson PowerLite Cinema 550 projector. Windows 7 refuses to recognize that the projector is connected under normal conditions (I'll get to the strange condition in a moment). Here are some things that I have already tried: Confirm that the projector continues to work well on my old Windows XP laptop. Confirm that the video cable (HDMI to HDMI) is connected Make sure the Dell laptop is plugged in to wall power at all times Reboot both the computer and the projector Click "Detect" under the "Connect to an External Display" Windows dialog (no reaction) Click "Rigorous Display Detection" under NVIDIA Control Panel (dialog: none found) Checked "Force Television Detection on startup" under "My display is not shown..." in NVIDIA Control Panel (no effect) Here's where it gets weird... My projector has three states: off, standby and on. Standby means the power switch on the back is on, but the projector is effectively off (no picture, no access to menu or controls). When I plug in the HDMI cable while the projector is in standby, Windows detects the projector! It lets me switch to Duplicate, Extend, or Project Only mode, and adjusts the resolution appropriately. A new Generic Plug-n-Play monitor shows up in my device manager. A "Seiko EPSON PJ" display shows up in my NVIDIA control panel. Then if I turn my projector on, Windows no longer recognizes the display. This is true whether I turn the projector on while the HDMI cable is plugged in, or if I unplug the HDMI cable while turning on the projector. Anyone have any ideas, because I'm completely stumped...?

  Read the article

• What's the risk of running a Domain Controller so that it is accessible from the internet?

  - by Adrian Grigore

  I have three remote dedicated web servers at different webhosts. Adding them to a common domain would make a lot of administration tasks much easier. Since two of the servers are running Windows 2008 R2 Standard, I thought about promoting them to Domain Controllers in order to set up the windows domain. There's another thread at Serverfault that recommends this. At the same time I've read a lot of times on different websites that this is not a good idea because an domain controller should always be behind a firewall LAN. But I can't set up something like this because I don't have a LAN with a static IP accessible from the internet. In fact I don't even have a windows server in my LAN. What I have not found out is why exposing a DC to the Internet would be bad idea. The only risk I can see is that if someone penetrates one of my webservers, it should be much easier to penetrate the others as well. But as far as I can see that's the worst case scenario since I am only going my web servers to that domain, not any computers from my local network. Is this the only downside or does it also make it easier to penetrate one of my web servers in the first place? Thanks, Adrian

  Read the article

• Still about SSD potentials...write and read speed

  - by Macroideal

  I have been working on SSD (solid state disk) for several months..Problems and Questions hit my head unexpectedly..Coz i am a virgin in ssd... Especially these days I was testing the write-read speed of ssd, which I was always caring.... however result turned out not good as I expected, or even worse Three kinds of read-write were implemented in my test read and write directly from and into ssd, with openning ssd as a whole device. in windows: _open("\\:g", ***).. It can be very tricky and hairy that you'd write a data with size of folds of 512, at the disk position of folds of 512bytes... So, If you wanto write just a byte or 4 bytes, you'v to write at least a whole sector one time. Read and write data from and into files located in SSD... Read and Write data from and into files in mechanical Disk I compared the pratices below...I found ssd sucks...the ssd performs worse than mechanical disk... so i am wondering where i can get the potential performance of ssd, since ssd is said to a substitute for mechanical disk in the future.. Nevertheless, I test ssd with a pro-hard-disk tools..ssd is like twice speedier than mechanical disk. So, why?

  Read the article

• Hyper-V virtual machine can't be migrated to a specific host in the cluster

  - by Massimo

  I have a three-node Hyper-V cluster running on Windows Server 2008 R2 which is working quite flawlessly: there are no errors, live migration works, all hosts can and will happily run all virtual machines, and so on. But one specific virtual machinee is trying to make me go mad: it works on two nodes of the cluster, but not on the third one. Whenever I try to move the VM to that node, be it in a live migration or with the VM powered off, it always fails. In the event log of the host these events are logged: Source: Hyper-V-VMMS Event ID: 16300 Cannot load a virtual machine configuration: General access denied error (0x80070005) (Virtual machine ID <GUID>) Source: Hyper-V-VMMS Evend ID: 20100 The Virtual Machine Management Service failed to register the configuration for the virtual machine '<GUID>' at 'C:\ClusterStorage\<PATH>\<VM>': General access denied error (0x80070005) Source: Hyper-V-High-Availability Event ID: 21102 'Virtual Machine Configuration <VM>' failed to register the virtual machine with the virtual machine management service. All other VMs can be moved to/from the offending host, and the offending VM can be moved between the other two hosts. Also, this is not a storage problem, because there are other VMs in the same cluster volume, and the host has no troubles running them. What's going on here?

  Read the article

• Cisco SG200 vlan issue in ESXi VSA cluster

  - by George

  I have three Cisco SG200-26 switches, and I also have two ESXi hosts that I have connected like shown in the below "best practice" map by VMware: http://communities.vmware.com/servlet/JiveServlet/previewBody/17393-102-1-22458/VSA_networking_map.pdf Even though I created the VLANs in the SG200 and I set the two VLANs (508 and 608) as allowed for these untagged ports (where my ESX NIC's are connected), I can not ping from host 1 to host 2 when configuring the NIC's to use 608 VLAN. Am I missing something? my IP's are all in the 192.168. range, and the only reason I need the VLANs is to isolate the traffic of VSA back-end internally, only the two hosts will be using the VLANs. So I think I do not have to create virtual interfaces on my router since that's the case, is my understanding correct? Also sending my switch config screenshot below.. all 3 switches have the latest firmware (it seems these were originally linksys and got rebranded as cisco after the acquisition) http://img31.imageshack.us/img31/2503/switch.gif Any ideas what to change on the Cisco SG200 to make this work , would be appreciated! The second VLAN (608) only needs two IP's: 192.168.0.1 and 192.168.0.2 The first VLAN (508) will have about 15 IP's for ESXi Management and VSA cluster service, I could use either 192.168.1.xx or 10.0.1.xx The rest of my network (about 50 clients) is in 192.168.1.xx range VMware also states that the VLAN protocol on the physical switch must be 802.1Q, not ISL, anyone knows which of the two my SG200-26 uses? In addition to that, the only requirement from VSA is that my two hosts: -Are in the same subnet. -Have static IP addresses set. -Have the same Default Gateway configured. If I need inter-vlan routing for this, I suppose I have to create virtual interfaces on my sonicwall, and assign an IP for each VLAN, and then set routes between them? Thank you for your time!

  Read the article

• Sticky sessions not sticky on coldfusion cluster

  - by GreatSeaSpider

  we're trying to deploy a legacy coldfusion site onto a new CF8 cluster. The cluster consists of three cf instances running under JRUN4 on a single windows 2008 server. I've got the cluster set to not replicate sessions, and sticky sessions turned on. each instance is set to use J2EE session variables. The application tag for the site has: sessionmanagement="Yes" setclientcookies="Yes" setdomaincookies="Yes" when each instance starts... no errors are reported in the instance log and they join the cluster without any issues. though the intances do have: 16/10 08:31:25 info SessionReplicationService successfully joined a JINI lookup service (assigned JINI-ID .....) and 16/10 08:31:25 info Clusterable service SessionReplicationService discovered a SessionReplicationService peer on a JRun server named "xxxx" on host xxxx which is interesting since session replication is definately off, is the SessionReplicationService responsible for sticky sessions aswell? thats enough background, the problem is that the sticky sessions appear to simply not work, each request is bounced to a different instance, and it seems as if the sessions are being lost on each instance anyways? As soon as the cluster is down to a single instance, the web app works exactly as expected and the sessions seem fine. has anybody got any ideas for me? i've been trawling the web and I cant seem to find any answers.

  Read the article

• Outlook 2007 / 2010 Calendar: hide meetings in specific category

  - by Jeroen

  Question Is there any easy way in Outlook 2007/2010 to show/hide meetings in a specific category? Preferably only for a specific view (the Month view, in this case). Note: I was almost done writing this question, adding just one more "What I've tried" option, when I found an acceptable (though imperfect) solution. Remembering this SE blog post I figured I might as well post it after all and answer it myself. And who knows, perhaps someone else has a more elegant solution. The reason for me personally is that I'd like to hide the "small, recurring meetings" like our daily stand-up meeting in the month view. I'd prefer an Outlook feature that is meant for this (there must be one for this, right?), but I'm open to workarounds or plugin suggestions as well. What I expected to find somewhere was a list of categories (with added option "No category") where you could select/deselect from which categories you'd see meetings. Something like this mock-up: What I've tried Edit "View Settings", and use a "Filter..." on categories. This has several disadvantages, the major one is that the filter only allows me to choose what I want to show, but not what I want to hide. Even if I tick all categories but one for the filter it would still hide any uncategorized meeting. Similar to 1, but then using Advanced filters. Still a bit clumsy as changing views can be up to three clicks, but this is the best solution so far (see the corresponding answer below). Creating a sub-calendar for these "small" meetings that I wish to hide. This felt a bit clumsy and like overkill, but did provide an easy "select/deselect" option to show/hide these meetings. Search for plug-ins that do this. Couldn't find one (yet).

  Read the article

• NFS v4, HA Migration, and stale handles on clients

  - by Karl Katzke

  I'm managing a server running NFS v4 with Pacemaker/OpenAIS. NFS is configured to use TCP. When I migrate the NFS server to another node in the Pacemaker cluster, even though the metadata is persisted, connections from the clients 'hang' and eventually time out after 90 seconds. After that 90 seconds, the old mountpoint becomes 'stale' and the mounted files can no longer be accessed. The 90 second grace period seems to be part of the server configuration and not the client configuration. I see this message on the server: kernel: NFSD: starting 90-second grace period If I restart the NFS client on the client nodes after I migrate (unmounting and then remounting the share), then I don't experience the problem, but connections and file transfers still interrupted. Three questions: What is the 90 second grace period? What's it there for? How can I keep the files from going stale on the clients without restarting them after I migrate the NFS server to another node? Is it actually possible to migrate the NFS server without having large file uploads drop?

  Read the article

• Folder Redirection Issues - Freezing, Strange Warnings

  - by JCardenas

  I have Folder Redirection set up in a test environment for a couple accounts. I have followed the instructions for setting up the folder security settings here, and I can confirm that folders are created automatically by the system with the correct security settings when a user logs in. The GPO has been configured to automatically move user files up to the redirected folders, and this is working properly. Problems start occurring when a Windows 7 PC is in use. It is rare, but Explorer will lock up when performing a file write operation (move/copy/save from application). This results in the entire system being unusable, with only a hard reset resolving it (Task Manager doesn't start, the "three finger salute" does nothing, apps stop working). The mouse functions, but clicks do nothing. The other issue is that occasionally when copying/creating/modifying files a dialog box will pop up with the message "You need permission to perform this action. You require permission from XYZ\cardenas to make changes to this folder." The folder that was created by copying an existing one has the correct security settings and lists me as the owner. My company will not be implementing Folder Redirection on XP, since we are making a "clean break" with implementing new technologies with the Windows 7 rollout, so this behavior has not been - nor will be - checked for in XP. Thanks in advance for your help!

  Read the article

• Network cabling with multiple patch panels?

  - by dannymcc

  I am in the very early stages of planning a network cabling upgrade in our office, mainly to upgrade the old cables from Cat5 to either 5e or 6. I am also planning on upgrading all of our 10/100 switches to 10/100/1000 switches. I would like to have three small wall mounted cabinets spread around the building, each with a patch panel and switch. These would all lead back to our server room. The question is; should I have two patch panels in each wall cabinet, one with 24 or 48 ports that are connected to a matching patch panel in the server room. The second patch panel would then link to each device in that cabinets area. Then I wouldn't put a switch in the small cabinets. All switching would be done in the server room. Or, should I have one main cable from the server room to each of the cabinets - plugged straight into the switch and the patch panel is for devices in the cabinets area? I hope that makes sense!

  Read the article

• Can't install NPM after installing Node on EC2 Linux instance?

  - by frequent

  I'm trying my first attempt on getting a node server set up on an amazon ec2 linux instance. I think I made it quite far. First problem I ran into was when trying to make Node the connection timed out after a while, so I need three attempts until I got this: LINK(target) /home/ec2-user/node/out/Release/node: Finished touch /home/ec2-user/node/out/Release/obj.target/node_dtrace_header.stamp touch /home/ec2-user/node/out/Release/obj.target/node_dtrace_provider.stamp touch /home/ec2-user/node/out/Release/obj.target/node_dtrace_ustack.stamp touch /home/ec2-user/node/out/Release/obj.target/node_etw.stamp make[1]: Leaving directory `/home/ec2-user/node/out' ln -fs out/Release/node node Which tells me, "Node is done", although I'm not sure it is also working as it should. Following this,this and this tutorial, I'm now stuck at installing npm. I think I first cloned into the wrong folder, which always gave me error 127, but even if I'm doing this: cd ~ git clone git://github.com/isaacs/npm.git cd npm sudo -s PATH=/usr/local/bin:$PATH make install I'm still getting this: #after cloning# make[1]: Entering directory `/root/npm' node cli.js install bash: node: command not found make[1]: *** [node_modules/.bin/ronn] Error 127 make[1]: Leaving directory `/root/npm' make: *** [man/man3/start.3] Error 2 Question:: Since I'm pretty much a newby at everything I'm trying here, can someone please tell me what I'm doing wrong and how to get npm to install? Also, in case I cloned into the wrong folder, is there a way to remove the "false clone" or is this not written to disk until I call make install and I don't need to worry? Thanks for helping out!

  Read the article

• Limit Apache 2 Memory Usage

  - by UltraNurd

  I am running a hobby webserver off of an ancient Blue & White G3/300 running Debian PPC Squeeze 2.6.30. The performance is okay for a while after a restart, but it eventually gets more and more bogged down. Right now it's at 76 days uptime, and the main culprit seems to be the memory usage of 10+ apache2 processes. I think I need to lower the values for StartServers, MinSpareServers, and/or MaxSpareServers, but I'm not sure which one to adjust, and there are three sections for each depending on which mpm module is in use. How do I tell which of the following sections I need to change, and what are some reasonable values given that the box has 448 MB physical memory (weird upgrade history of one each 64, 128, and 256 sticks)? <IfModule mpm_prefork_module> StartServers 5 MinSpareServers 5 MaxSpareServers 10 MaxClients 150 MaxRequestsPerChild 0 </IfModule> <IfModule mpm_worker_module> StartServers 2 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxClients 150 MaxRequestsPerChild 0 </IfModule> <IfModule mpm_event_module> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadLimit 64 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> There aren't any other instances of StartServers in my apache2.conf, but none of those mpm modules appear in mods-available or mods-enabled. Ideas? Thanks!

  Read the article

• Reviving a dead laptop battery

  - by Alex Ciminian

  Is there any way to revive a dead laptop battery? I have a three year old Dell Latitude laptop that I've been using pretty intensively. After a year or so, the battery dropped dead - if I plug the laptop out it goes into hibernation in a matter of seconds. Probably this was because I kept working on it plugged in all the time, but back then I didn't realize what effect it could have (this was my first laptop). Currently, I'm searching for a new laptop and I was thinking if there was something I could do to get the battery back working. I've found several links (sorry, I'm a new user so I can't post them) about freezing Li-ion batteries, but the opinions seem to mixed - some say that it worked for them, some not. If you've tried the freezing technique please let me know if it works. Or if you know another way to make a dead battery work again, please share here. I've already seen this thread, but I'm not very handy with soldering. If it's the only alternative I'll try it, but there's a big chance that I'll screw it up. Thanks!

  Read the article

• Problems with freetype on OSX 10.7.4

  - by eythor

  I'm trying to install mplayer with OSD using homebrew. I've added both --enable-menu and --with-freetype-config=/usr/local/Cellar/freetype/2.4.10/freetype-config to the brew recipe. ==> Downloading http://www.mplayerhq.hu/MPlayer/releases/MPlayer-1.1.tar.xz Already downloaded: /Library/Caches/Homebrew/mplayer-1.1.tar.xz xz -dc "/Library/Caches/Homebrew/mplayer-1.1.tar.xz" | /usr/bin/tar xf - ==> ./configure --prefix=/usr/local/Cellar/mplayer/1.1 --cc=cc --host-cc=cc --disable-cdparanoia --disable-libopenjpeg --enable-menu --disable-x11 -- with-freetype-config=/usr/local/Cellar/freetype/2.4.10/freetype-config ./configure --prefix=/usr/local/Cellar/mplayer/1.1 --cc=cc --host-cc=cc --disable-cdparanoia --disable-libopenjpeg --enable-menu --disable-x11 --with -freetype-config=/usr/local/Cellar/freetype/2.4.10/freetype-config Checking for cc version ... clang 4.2.1 (experimental support only) Checking for working compiler ... yes Detected operating system: Darwin Detected host architecture: x86_64 Checking for cross compilation ... no Checking for host cc ... cc Checking for CPU vendor ... GenuineIntel (6:15:10) Checking for CPU type ... Intel(R) Core(TM)2 Duo CPU T7700 @ 2.40GHz For freetype-config I've tried three seperate paths; /usr/X11R6/bin/freetype-config, /usr/X11/bin/freetype-config and the one in Cellar. Checking for freetype always fails: Checking for freetype >= 2.0.9 ... no Checking for fontconfig ... no (FreeType support needed) Although freetype itself seems to be installed. mufasa:bin eythor$ freetype-config --version 15.0.9 mufasa:bin eythor$ freetype-config --ftversion 2.4.10 mufasa:bin eythor$ freetype-config --libs -L/usr/local/Cellar/freetype/2.4.10/lib -lfreetype -lz -lbz2 mufasa:bin eythor$ freetype-config --cflags -I/usr/local/Cellar/freetype/2.4.10/include/freetype2 - I/usr/local/Cellar/freetype/2.4.10/include I'm not sure what to try next or how to figure out why freetype isn't recognized. Can anyone point me in a sensible direction?

  Read the article

• Solaris 10 zlogin logs in, logs out immediately

  - by Spelevink

  On a SPARC v445 running Solaris 10 9/10, had to rebuild rpool and reattached the three existing mirrored zpools on the other existing disks, with their zfs filesystems and NG zones intact. The zones have been configured with zonecfg -z ZONENAME create etc. ... and are now online using zoneadm -z ZONENAME attach -U then simply booting after being in installed state, but I cannot zlogin to any of the zones except one. It shows that I am logged in, then a blank line, then immediately logged out again. When I try to login using zlogin -C ZONENAME I cannot; the error message is: May 15 15:43:46 <hostname> login: open_module: stat(/usr/lib/security/pam_mkhomedir.so.1) failed: no such file or directory. May 15 15:43:46 <hostname> login: load_modules: cannot open module /usr/lib/security/pam_mkhomedir.so.1 But /usr/lib/pam_mkhomedir.so.1 does not exist, and it does not exist on my other servers, but those zones are accessible using zlogin. I can only zlogin to the zones with zlogin -S ZONENAME. What to do next? Thank you.

  Read the article

• How to configure Farsun USB barcode scanner to not auto-trigger

  - by David Grayson

  At my company we have several USB barcode scanners. I'm not sure exactly what model they are, but I think they are the FG9800 from Farsun because that's what they look like on the exterior. They came with a programming manual that is very similar to this document from the Farsun website. When I scan the "Output Firmware Version" barcode, my scanner types the following into the computer: Farsun V2.00 2011-01-01 Is it possible to configure these scanners so they only read barcodes in response to the trigger button being pressed? I don't want them to automatically read barcodes. Additionally, I want this setting to be remembered while the scanner is turned off. Since this scanner only has a USB port, the only way to configure it that I know of is to scan bar codes from the manual (or make your own). I have tried scanning the configuration bar codes for Single Scan (013300), Single Scan No Trigger (013301), and Laser/CCD Timeout - 5 Seconds (0134005) from this document. Sometimes (but not often) this puts the scanner in to the right mode, where it only scans when the button is pressed. Unfortunately, the scanner seems to always leave this mode when it is power cycled. I have also scanned the "Reset Configuration To Defaults" barcode (0B) many times. We have three different scanners like this and I have not been able to successfully configure any of them. If the things I want are not possible with these Farsun-based scanners, is there some other scanner we can use?

  Read the article

• Chroot jail of Nginx and php

  - by sqren

  I'm hosting multiple websites on one VPS, and want to chroot each website, eg. /chroot/website1 /chroot/website2 I'm using makejail, which is a highlevel tool, for creating the jails, and copying the libraries and dependencies. Easy peasy. Each website will need nginx, php and mysql. For php I'm using php5-fpm which actually supports chroot by configuration, however I'm not using this (maybe I should?) My question is which approach of the following three is the better: 1) Every website will have its own seperated instance of nginx, php and mysql. The downside is, that each webserver + php has to listen to a different port. I also need a "master" nginx web server in front of them, reverse proxying to the chrooted servers behind it. Probably most secure, but also most advanced. 2) I don't make any chroot jails manually. I setup one nginx web server, that proxies php requests to php-fpm, on different ports. I can have multiple php-fpm configurations each with is own chroot'ed folder. This is quite managable - however only php will be chrooted. Not the actual webserver. Is this secure enough. Also, I tried this option out, and it seems I will need to use TCP instead of sockets for connecting to MySQL. 3) You tell me ;) I'm quite new to chroot jailing, so please correct me if I'm wrong in my assumptions. I've been reading all the tutorials I could find, however, I find the market for chroot guides very scarce. Any help or inputs much appreciated!

  Read the article

• Vserver: secure mails from a hacked webservice

  - by lukas

  I plan to rent and setup a vServer with Debian xor CentOS. I know from my host, that the vServers are virtualized with linux-vserver. Assume there is a lighthttpd and some mail transfer agent running and we have to assure that if the lighthttpd will be hacked, the stored e-mails are not readable easily. For me, this sounds impossible but may I missed something or at least you guys can validate the impossibility... :) I think basically there are three obvious approaches. The first is to encrypt all the data. Nevertheless, the server would have to store the key somewhere so an attacker (w|c)ould figure that out. Secondly one could isolate the critical services like lighthttpd. Since I am not allowed to do 'mknod' or remount /dev in a linux-vserver, it is not possible to setup a nested vServer with lxc or similar techniques. The last approach would be to do a chroot but I am not sure if it would provide enough security. Further I have not tried yet, if I am able to do a chroot in a linux-vserver...? Thanks in advance!

  Read the article

< Previous Page | 349 350 351 352 353 354 355 356 357 358 359 360  | Next Page >