Search Results

Search found 18841 results on 754 pages for 'path finding'.

Page 462/754 | < Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >

• Can't configure frame relay T1 on Cisco 1760

  - by sonar

  For the past few days I've been trying to configure a data T1 via a Frame Relay. Now I've been pretty unsuccessful at it, and it's been a while, since I've done this so please bare with me. The ISP provided me the following information: 1. IP address 2. Gateway address 3. Encapsulation Frame Relay 4. DLCI 100 5. BZ8 ESF (I think the bz8 was supposed to be b8zs) 6. Time Slot (1 al 24). And what I have configured up until now is the following: interface Serial0/0 ip address <ip address> 255.255.255.252 encapsulation frame-relay service-module t1 timeslots 1-24 frame-relay interface-dlci 100 sh service-module s0/0 (outputs): Module type is T1/fractional Hardware revision is 0.128, Software revision is 0.2, Image checksum is 0x73D70058, Protocol revision is 0.1 Receiver has no alarms. Framing is **ESF**, Line Code is **B8ZS**, Current clock source is line, Fraction has **24 timeslots** (64 Kbits/sec each), Net bandwidth is 1536 Kbits/sec. Last module self-test (done at startup): Passed Last clearing of alarm counters 00:17:17 loss of signal : 0, loss of frame : 0, AIS alarm : 0, Remote alarm : 2, last occurred 00:10:10 Module access errors : 0, Total Data (last 1 15 minute intervals): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs Data in current interval (138 seconds elapsed): 0 Line Code Violations, 0 Path Code Violations 0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins 0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 0 Unavail Secs sh int: FastEthernet0/0 is up, line protocol is up Hardware is PQUICC_FEC, address is 000d.6516.e5aa (bia 000d.6516.e5aa) Internet address is 10.0.0.1/24 MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s, 100BaseTX/FX ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:20:00, output 00:00:00, output hang never Last clearing of "show interface" counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue: 0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog 0 input packets with dribble condition detected 191 packets output, 20676 bytes, 0 underruns 0 output errors, 0 collisions, 1 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier 0 output buffer failures, 0 output buffers swapped out Serial0/0 is up, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY, loopback not set Keepalive set (10 sec) LMI enq sent 157, LMI stat recvd 0, LMI upd recvd 0, DTE LMI down LMI enq recvd 23, LMI stat sent 0, LMI upd sent 0 LMI DLCI 1023 LMI type is CISCO frame relay DTE FR SVC disabled, LAPF state down Broadcast queue 0/64, broadcasts sent/dropped 2/0, interface broadcasts 0 Last input 00:24:51, output 00:00:05, output hang never Last clearing of "show interface" counters 00:27:20 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair Output queue: 0/1000/64/0 (size/max total/threshold/drops) Conversations 0/1/256 (active/max active/max total) Reserved Conversations 0/0 (allocated/max allocated) Available Bandwidth 1152 kilobits/sec 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 23 packets input, 302 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 1725 input errors, 595 CRC, 1099 frame, 0 overrun, 0 ignored, 30 abort 246 packets output, 3974 bytes, 0 underruns 0 output errors, 0 collisions, 48 interface resets 0 output buffer failures, 0 output buffers swapped out 4 carrier transitions DCD=up DSR=up DTR=up RTS=up CTS=up Serial0/0.1 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never Serial0/0.100 is down, line protocol is down Hardware is PQUICC with Fractional T1 CSU/DSU Internet address is <ip address>/30 MTU 1500 bytes, BW 1536 Kbit, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation FRAME-RELAY Last clearing of "show interface" counters never And everything seems to be accounted for to me, but apparently I'm missing something. My issue is that I'm stuck on interface up, line protocol down, so the T1 doesn't go up. Any ideas? Thank you,

  Read the article

• Can I have a single solid state drive and a RAID array on the same machine? [closed]

  - by jaminto

  Hi- To summarize, i'm looking to use a single solid state drive as my primary drive, and two conventional sata drives in a RAID 1 configuration for data. I am trying to install 64-bit Windows 7 onto this configuration. Is this possible? Here are the details: I built a desktop that has been running 64-bit Vista on two 500Gb in a RAID 1 array for a few years. I just purchased an Intel X25-M 80Gb Sata Solid-State Drive, and was planning on using this a my primary drive, and keeping the RAID 1 array as my data drive. I added the SSD drive and in the RAID setup, configured it as a RAID 0 array of only one disk. Then, I tried to do a clean install of windows 7 64-bit, but got stuck in the "Missing driver for CD/DVD drive" black hole of selecting driver files and Windows telling me that i don't have the appropriate driver for my hardware. The missing hardware is NOT a CD/DVD drive, since i'm installing off of my only CD/DVD drive. Plus at one point i was able to point it at a driver for my raid controller, and then my hard drives magically showed up as browsable sources for finding drivers for some other unnamed device that setup couldn't recognize. After a few hours of trying drivers (this was a very slow process) i decided to reboot and look at the BIOS settings. I'm using an ASUS M2A-VM motherboard which has an ATI SB600 RAID controller on board. I switched the "On board SATA Type" setting from "SATA" to "AHCI" thinking that since AHCI is an Intel thing, this would help. Unfortunately, this abandoned my RAID configuration, and my previously mirrored drives are showing up as separate drives when i boot into my current windows installation. Am i trying to do the impossible here? Should i just buy a separate SATA/RAID PCI card and plug the SSD into that? Any help would be greatly appreciated.

  Read the article

• Postfix not delivering from external senders and not logging anything

  - by simendsjo

  Some semi-recent upgrades must have broken my postfix+dovecot configuration, but I'm having problems finding out what the cause is. My domain is simendsjo.me with the MX record mail.simendsjo.me. I can send mail to both local and external recipients, and it delivers mail from internal mailboxes. The problem is that mail from external senders isn't delivered, and nothing is logged at all. The external sender also doesn't receive any errors. I have no idea where to ever start looking as nothing is logged at all when external mail is sent to my server. So the first issue would be: How can I turn on some debug messages for postfix? I've tried: debug_peer_level = 2 debug_peer_list = simendsjo.me .. And _level = 999 and _list = gmail.com where I'm trying to send emails from. but nothing is logged. When sending mails from a local mailbox (but from an outside computer, not localhost), a lot is logged. I don't have any rules in iptables either. Any ideas how I can get some debug messages for postfix?

  Read the article

• ESX 3.5 refuses to update

  - by Speeddymon

  I have a set of ESX 3.5 servers in 2 different datacenters. One is DR, one is production. They are on the same vlan and so I can access any of them on the private network from my vCenter server. Last month, as a learning experience (I hadn't dealt with ESX much before), I updated the DR server. Other than finding out that a couple of bundles had to be installed manually in order to get the rest to install from vCenter, it went off without a hitch. Now, I'm trying to do the same for our production servers and it is not working. I've googled around for the error I get during scan, and investigate loads of different solutions (editing the integrity file, checking DNS, etc) -- I did install the 2 bundles that had to be installed manually already -- but scan from vCenter is just not working. Side note: I did just scan the DR server again and that scan works fine so shouldn't be a problem with vCenter that has cropped up recently -- it has to be something else. The error I get is: Patch metadata for (servername) missing. Please download updates metadata first. Failed to scan (servername) for updates. I'm all out of ideas on how to make this work, so any help would be hugely appreciated.

  Read the article

• Why is my browser using so much memory?

  - by Steve

  Hi. I've recently had problems with Firefox running very slowly when I have many tabs open; say 20 tabs. My whole system would slow down. I decided to give Google Chrome a try, and it started out fine. But lately I am finding that it too, slows down my whole system. Looking at Task Manager, chrome.exe is using about 250MB of memory in about 6 different entries in task manager. However, when I shut Chrome down, memory usage is reduced by about 600MB. How can this be? (shows drop in memory usage after ending Chrome.) When my system locks up with Chrome having many tabs open, it takes 10 seconds to load the Start Menu, 10 seconds to expand All Programs, and each folder and subfolder, and 30 seconds for the program to be highlighted under my mouse. It also takes 10 seconds to switch to Notepad. Why is Chrome appearing to use so much more memory than Task Manager indicates? Why is my pagefile being used when I have around 1.1GB of memory? Can I set Chrome to run in RAM and not in the pagefile? How can 20 tabs use 600MB? That's 30MB per tab. Thanks for your help.

  Read the article

• Best way to patch (8) RJ45 ports from one room to another.

  - by zimmer62

  I have a 48 port patch panel in my basement, which I've wired almost all of them to various rooms around the house. Many are not actually being used at the moment, but pretty much all of them are wired to somewhere. As of recent, I've put in an HTPC in my media closet (different room), and I'm finding I need a lot more RJ45 plugs to this area. I have 4 drops here, and adding a switch will not solve my problems. I'm using the cabling for other things such as IR and Serial devices, not just Ethernet. What I'm hoping to do is add an 8 port panel in that media closet, and tie those into an 8 port panel on my rack next to the 48 port... What I don't want to do is pull 8 separate cables one by one from one area to the other unless someone has a technique that will allow me to do that quickly, and painlessly. Do they make cables with more conductors specifically for this purpose? Or patch panels that are designed for a special cable essentially just extending ports from one room to another?

  Read the article

• Efficient mirroring of directories using hardlinks

  - by zoqaeski

  I'm backing up my music collection on to a number of NTFS-formatted external hard-drives; however, as I store my main collection in FLAC and have my library on my laptop as MP3s to save space, I want to be able to back up both sets, because mass conversion between formats is time-consuming. The "music" directory can contain any format; the "mp3s" directory contains only MP3s converted from files in the "music" directory. The music collection on the laptop contains only MP3s, but they come from both sources. When I backup my laptop's library to the "mp3s" directory, I want to only copy across MP3 files that don't exist in the "music" directory; those that do should be hard-linked to the "music" directory. All directories have an identical hierarchy, sorted by artist, album, date, discnumber if applicable, etc, and I use a tagging editor to ensure consistency across all these locations. I'm also using a Linux computer, but keeping the music collections on NTFS-formatted partitions so that they are readable by both Linux and Windows. At the moment, I use the following command to perform the backups, but this is time-consuming due to the expensive nature of finding hard links. rsync -avu --progress --relative --ignore-existing --link-dest=../music/ **/*.mp3 /media/ntfspocket/mp3s Is there a way to perform this backup more efficiently, taking advantage of the directory hierarchy?

  Read the article

• How should an experienced Windows SysAdmin learn Linux? [closed]

  - by Systemspoet

  I have a new hire starting in a few weeks who is an experienced Windows SysAdmin. I think he's fairly senior on the Windows side, with a pretty deep AD understanding and experience with Exchange 2007, 2010, and exchange migrations. He's done a little PowerShell but I suspect more of the "run this command to do this" variety then "write a script to do this" sort. However, we are a mixed shop and (he knows this) I expect him to become a reasonably competent Linux SysAdmin over time. I'm looking for good starting points to bring him along. I have over ten years of Linux/UNIX experience, so it all sort of seems intuitive to me, but I've been thinking about the toolkit you actually need to be productive in the Linux CLI world. Just to be able to use the machines at all, off the top of my head... vi Basic CLI stuff -- move around, rename files, copy files, tar, gzip, changing passwords, finding relevant manpages, keep track of where you are, find things in your history, etc, etc. More advanced things that I take for granted but are actually pretty hard -- doing things with 'find', extracting relevant text via 'awk' and/or 'cut', knowing when to use 'grep' and when to use 'grep -e' or 'egrep'. Distribution specific stuff... compiling software, rpm, yum, apt-get, you name it. This all seems pretty basic to me, but when I think back to 1995 when I was first learning my way, some of those things took me years to master. So my question is -- where should I send him to pick up those skills? I'm not just thinking of classes, but rather also websites and books? Where do you all suggest as a starting point for picking up Linux skills?

  Read the article

• Corsair SSD appears completely blank and does not retain written data

  - by ebanders

  I have a 180GB Corsair SSD (model# CSSD-F180GB2-BRKT) as the primary drive in a Windows laptop. Recently the machine became unbootable after installing Windows updates. Windows installed updates before the machine shut down and the next time the machine boot up it complained about not being able to find a bootable device. After finding fixmbr unsuccessful at making the machine unbootable, I investigated a little within knoppix. Fdisk revealed an empty partition table. A scan by Testdisk came up empty. And finally 'head -c 1024 | hd' reveals all zeros. Creating a primary partition spanning the whole disk completes successfully, but after a reboot the disk appears empty again. dmesg reveals no read or write errors. smartctl indicates that the drive is healthy- although the SMART attribute values do not appear to be read properly. "Data Page | WARNING: PREVIOUS ATTRIBUTE HAS TWO" and "Threshold Page | INCONSISTENT IDENTITIES IN THE DATA" messages appear within the table of values. I don't have much experience with SSDs. Is this drive dead or something? Can anyone recommend any diagnostic tools that may be suited for diagnosing SSDs?

  Read the article

• Scaling a node.js application, nginx as a base server, but varnish or redis for caching?

  - by AntelopeSalad

  I'm not close to being well versed in using nginx or varnish but this is my setup at the moment. I have a node.js server running which is serving either json, html templates, or socket.io events. Then I have nginx running in front of node which is serving all static content (css, js, etc.). At this point I would like to cache both static content and dynamic content to memory. It's to my understanding that varnish can cache static content quite well and it wouldn't require touching my application code. I also think it's capable of caching dynamic content too but there cannot be any cookie headers? I do use redis at the moment for holding session data and planned to use it for other things in the future like keeping track of non-crucial but fun stats. I just have no idea how I should handle caching everything on the site. I think it comes down to these options but there might be more: Throw varnish in front of nginx and let varnish cache static pages, no app code changes. Redis would cache dynamic db calls which would require modifying my app code. Ignore using varnish completely and let redis handle caching everything, then use one of the nginx-redis modules. I'm not sure if this would require a lot of app code changes (for the static files). I'm not having any luck finding benchmarks that compare nginx+varnish vs nginx+redis and I'm too inexperienced to bench it myself (high chances of my configs being awful). I'm basically looking for the solution that would be the most efficient in terms of req/sec and scalable in the future (throw new hardware at the problem + maybe adjust some values in a config = new servers up and running semi-painlessly).

  Read the article

• How does everyone set up AWS for PHP with a git workflow while worrying about distributing EC2?

  - by Parris

  Hello, I have been looking for something like heroku but for php, and after much frustration (and almost finding what I need, but not quite) we decided to just go with AWS without any other abstraction. We are using PHP 5.3 (and CakePHP 1.3), and are currently using git. Ubuntu seems like the easiest way to get both of those on there and we will most likely use that. We aren't really going worry about outgoing email. We are using smtp through gmail, but will most likely switch to some other service eventually. I had 3 questions: 1) I have been looking at Zend Server, and I am not quite sure how that is more beneficial than xampp. Perhaps it is not? 2) I suppose to make the application scale we would need multiple instances of some ec2 ami. Then just duplicate it and such. The question then becomes how do we make sure all EC2 instances are up to date? 3) I understand the concept of load balancing to some degree. I understand that in 1 region you select a bunch of servers and have it load balance across them. The question then becomes well how about world wide? How do I make it so that traffic is directed to the correct ec2 server? I have heard of route 53, and tried signing up for that, but nothing appears in my control panel. Also perhaps it is just a DNS thing with my domain registrar? AHHH... some tutorial would be helpful!

  Read the article

• Paranormal activity in My Pictures folder: Thumbnail doesn't match actual picture.

  - by Sam152

  After finding an amusing picture on a popular imageboard, I decided to save it. A few days past and I was browsing my images folder when I realised that the thumbnail generated by Windows XP in the thumbnails view did not match the actual image. Here is a comparison image: What's even stranger in this situation is that the parts of the photograph that are different have actually been replaced with what might be the correct background. Furthermore, it is a jpeg (no PNG transparency tricks) that is 343 kilobytes but only 847x847 pixels wide. What could be going on here? Could there be anything malicious in the works, or hidden data? Before anyone asks, I have checked and preformed the following: Deleted Thumbs.db to reload thumbnails. Opened image in different editors. (they appear with the text) Moved image to a different directory. Changed the extension to .rar. All these steps produce the same results. Pre actual posting update: It seems that opening the image in paint, changing the image entirely (deleting entire contents and making a red fill) will still generate the original thumbnail, even after deleting Thumbs.db etc. I'm also hesitant to post the original data, in case there is something malicious or hidden that could be potentially illegal. (Although it would be very beneficial to see if it works on other computers and not just my own).

  Read the article

• Identifying Exchange 2010 regular process that is walking the mailbox database

  - by toongeneral

  I have an Exchange 2010 server running on a SAN-backed platform. The platform does block-level backups based on a snapshot/incremental basis, that only capture changed data. I was surprised to see a regular period of time where the data changes were happening at a high, sustained rate. Due to the way this system works, that can lead to 1.2TB of stored data per month. The regularity implied a scheduled task, but it is not a fixed interval. It is approximately every 26-32hrs. The disks were performing read operations of ~5MB/s and write operations of ~4.5MB/s, for a period of 3-4hrs. The total written data was ~55-60GB. Reading on TechNet, I am wondering if the following is causing this: http://blogs.technet.com/b/exchange/archive/2011/12/14/database-maintenance-in-exchange-2010.aspx#checksumming The somewhat restrictive thing is that the process only happens at most once every 24 hours. I was able to investigate while it was running, finding the following: the process is store.exe it is working on the mailbox database files while running, it is generating .log files (in the mailbox database folder) consistent with database changes the mailbox database is ~60GB in size, which fits with the total data changes on each iteration I have currently switched to a fixed maintenance window, as a test. It's not clear whether this is the cause, as the symptoms fit, but are not conclusive. Does anyone have any suggestions for additional troubleshooting?

  Read the article

• fglrx-legacy-driver not seeing Radeon HD 4650 AGP

  - by Rocket Hazmat

  I am running Debian Squeeze on an old Dell Dimension 8300 box. It has an AGP Radeon HD 4650 card. I use this machine to mine bitcoins, and today I noticed that the machine had rebooted! My precious uptime! Anyway, my miner wouldn't start, so I figured might as well update my graphics driver, maybe that would fix the issue. I went to amd.com and downloaded the newest driver (12.6 legacy), but after installing it, aticonfig gave an error: aticonfig: No supported adapters detected I uninstalled the driver and figured I'd try to install it from apt. AMD has dropped support for the HD 4000 series in fglrx, forcing me to use fglrx-legacy-driver (currently only in experimental). In order to install this, I had to update libc6 (and some other important packages, like gcc), I had to use their wheezy versions. I finally got glrx-legacy-driver installed, but I still got: aticonfig: No supported adapters detected Why isn't the driver finding my video card? I have a hunch it has something to do with the fact that it's an AGP video card. Here is the output of lspci -v (why does it say Kernel driver in use: fglrx_pci?): 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV730 Pro AGP [Radeon HD 4600 Series] (prog-if 00 [VGA controller]) Subsystem: Advanced Micro Devices [AMD] nee ATI Device 0028 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16 Memory at e0000000 (32-bit, prefetchable) [size=256M] I/O ports at de00 [size=256] Memory at fe9f0000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fea00000 [disabled] [size=128K] Capabilities: [50] Power Management version 3 Capabilities: [58] AGP version 3.0 Kernel driver in use: fglrx_pci

  Read the article

• Is my current htaccess setting hurting SEO?

  - by user656002

  I have a site that I have redirecting to https. I do this to leverage wildcard SSL for my password protected pages. Everything seems to work fine with testing. For example, whether you type in http or www, you always get redirected to the SSL https... That said, I have about 200-300 external backlinks -- many high quality, yet google webmaster (along with SEOMoz), shows I have just 4... Huh? I'm embarrassed to say I just discovered this. This has led me to hypothesize that maybe my settings in htaccess is messed up, so google isn't recognizing a link because it's recorded on another site as http, instead of https. Maybe? At any rate, here is my simple htaccess setting for 301 www to http (The https redirect must be done inside the virtual host file--I think). I don't have anything in the htaccess file for https RewriteCond %{HTTP_HOST} ^www\.example\.com$ [NC] RewriteRule ^(.*)$ http://example.com/$1 [L,R=301] Like I said, everything works fine for redirect over https, so I'd rather not screw up what works. On the other hand something is very wrong with google finding all my back links, so I need to fix something... I'm just wondering that maybe google isn't picking up a my backlinks from other websites recording me as http because I'm at https. Maybe google doesn't care and it's some other issue. Am I barking up the right tree? If so any quick fixes? Thanks as always!

  Read the article

• Anyone recommend a program to print multiple HTML files at once for end users?

  - by Keith Bentrup

  I have some clients with multiple html files in folders that are occasionally updated & printed. They would like to be able to print them all at once without having to open each one. I typically do this with a quick command for myself, but I'm unaware of any freeware to do this. After a google search, I'm not finding one, so I'm hoping someone can help. I'd rather not use a script to do this for various security/ease of use/familiarity reasons, I'd rather be able to just point to a simple program they can download and use on their windows desktops. Anyone know of one or some other easy solution to do this? Maybe I'm overlooking the obvious. If anyone's curious, this is what I do for myself (not for my clients): for %h in (*.html) do type "%h" >> all.htm then open all.htm & print. If I need a page break on each doc, I just search and replace in all.htm </body> with <p style="page-break-after:always">&nbsp;</p></body>. It's quick & simple, but too unfamiliar for them. Thanks!

  Read the article

• Does OS X support linux-like features?

  - by Xeoncross

  I have been using XP for almost a decade. Contrary to popular belief, it has served me well. In the last 4 years I don't remember ever having it crash on me. It has the most stable GUI I have ever used. However, an OS is only as good as it's GUI AND command line combined. Windows command line is awful and totally useless. So I have been using Ubuntu for a couple years and Debian on my servers. The only problem is that Gnome applications (ubuntu 6-10) constantly crash on me (Ubuntu Studio was the most unstable OS I ever used). I have high quality Gigabyte, MSI, and Asus motherboards and CPU's from old Semprons/Athlons to Celerons/Core 2 Quads. What are the odds that every PC I have ever owned can't remain stable with a linux GUI? Not to mention that Adobe CSx Suite doesn't work on linux. Anyway, I am now looking at moving to a MAC in the hope of finding a stable GUI and a feature-packed command line. Does Mac OS have an integrated command line where I can do linux-like-awesomeness like rsync, ssh, wget, crong jobs, package updates, and git without having an unstable GUI? Basically, until the linux GUI applications get a little better, is OS X what I need?

  Read the article

• Driver corruption when deploying Dell Touchpad Drivers (with software) during imaging process

  - by BigHomie

  We're an sccm shop, and use it to deploy Windows. When deploying Dell laptops (multiple models), the touchpad drivers seem install properly, but the software doesn't. The resulting problem is that when the touchpad is pressed on occasion, the mouse pointer will 'jump' to certain points on the screen. A possible symptom of this problem/visible sign is if the touchpad icon isn't in the system tray. The software is in the control panel, but when opened part of the gui is pixelated, indicating botched install maybe? The manual resolution to this, is to go into device manager and uninstall the driver with the option to uninstall all driver software. After a restart, the driver and software is apparently reinstalled, and from there works as expected. Obviously this partially defeats the purpose of a zero touch deployment. If anyone knows why this is and/or a possible workaround, those answers would be valid as well. Barring that, I want to find a way to deploy the driver and touchpad software in an unattended way, so that it can be conditionally installing during the imaging process. To be honest I'm not sure how to troubleshoot this, I suppose I could try drvinst.exe to install the driver, but finding out why this fails initially would keep me from spinning my wheels.

  Read the article

• ZFS & Deduplicating FLAC Data

  - by jasongullickson

  I'm experimenting with using ZFS to deduplicate a large library of FLAC files. The purpose of this is twofold: Reduce storage utilization Reduce bandwidth needed to sync the library with cloud storage Many of these files are of the same music tracks but from different physical media. This means that for the most part they are the same and usually close to the same size, which makes me think that they should benefit from block-level deduplication. However in my testing I'm not seeing good results. When I create a pool and add three of these tracks (identical songs from different source media) zpool list reports 1.00 dedupe. If I copy all of the files (make exact duplicates of the three) dedupe climbs, so I know that it is enabled and functioning, but it's not finding any duplication in the original collection of files. My first thought was that perhaps some of the variable header data (metadata tags, etc.) might be mis-aligning the bulk of the data in these files (the audio frames) but even making the header data consistent across the three files doesn't seem to have any impact on deduplication. I'm considering taking alternate routes (testing other dedupe filesystems as well as some custom code) but since we're already using ZFS and I like the ZFS replication options, I'd prefer to use ZFS dedupe for this project; but perhaps it's simply not capable of working well with this sort of data. Any feedback regarding tuning that might improve dedupe performance for this sort of dataset, or confirmation that ZFS dedupe is not the right tool for this job are appreciated.

  Read the article

• Google Sites (via Apps) setup questions

  - by Dave

  I thought that it would be a piece of cake to set up a Google site via Google Apps, but perhaps my previous (limited) experience with web development has given me unrealistic expectations. I have actually had a really tough time finding help with the exact question that I have, which is: How do I change the home page contents??? You see, I'm used to having hosting with someone like GoDaddy, where I can just ftp in and drop my HTML files in the www folder. From research I have found that this is simply not possible with any flavor of Google Sites. That's fine, I can live with it. So let's say I have www.mydomain.com. When I hit that URL, it redirects me to a very long URL (unfortunately) like https://sites.google.com/a/mydomain.com/sites/system/app/pages/meta/domainWelcome, which just says: Google Apps Welcome to mydomain.com If you are the domain administrator get started creating your home page with Google Sites Great! I want to do that. So I click on the "If you are the..." link and end up at a screen where I can choose a template, a name, and some visibility options. If I click on My Sites, there isn't a "default" site, i.e. the one that www.mydomain.com displays. I figured that maybe I just have to create a site first, so I went ahead and did that. My first test was to create a site that was publicly accessible. I thought that maybe if I did that, the Google would decide that this must be my home page since it's the only one. But it doesn't, and I still get the "Welcome to" page. Under "More Actions", I didn't see anything interesting except for "Manage site". I went in there and had a peek around, and didn't see anything about using this as the default home page. Am I looking for something that just doesn't exist? I can't believe there isn't a way to modify the "domain welcome to" page...

  Read the article

• Two mouse, one left handed and another right handed. At the same time

  - by trailmax

  I would like to have two mouse connected to my computer, and have one mouse left-handed, another right-handed. And not needing to change any settings for using any of them. I've googled for this and did not find some information, but nothing helpful. Somebody suggested to have 2 accounts, some other suggested a short-cut that changes mouse buttons over. I did not like any of that. And I remember, I saw somebody using their laptop with right-handed touch-pad and left-handed mouse. At the same time. Both of my mouse are plain vanilla USB, with no drivers, tried finding drivers for any of the mouse did not get me anywhere. This is how mouse configuration looks like: There is no option for different mouse to be configured different. I think I need to install some mouse drivers/software that allow different configuration. Is there anything like this availble?? Many thanks in advance! p.s. Using Windows 7 Pro, one mouse is Fujitsu, another Sandsrom.

  Read the article

• Troubleshooting DTCPing Errors

  - by JimmyP

  So I am running DTC ping between 2 machines on our network and am getting the following error ++++++++++++++++++++++++++++++++++++++++++++++ DTCping 1.9 Report for WEB2 ++++++++++++++++++++++++++++++++++++++++++++++ RPC server is ready ++++++++++++Validating Remote Computer Name++++++++++++ 03-03, 13:39:45.099-->Start DTC connection test Name Resolution: internal-->10.20.3.236-->internal.something 03-03, 13:39:45.114-->Start RPC test (WEB2-->internal) Problem:fail to invoke remote RPC method Error(0x6BA) at dtcping.cpp @303 -->RPC pinging exception -->1722(The RPC server is unavailable.) RPC test failed I have also run RPC ping where I get what I beleive is the same error: C:\Program Files\Windows Resource Kits\Tools>rpcping -s internal Exception 1722 (0x000006BA) Number of records is: 4 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 1722 Detection location is 323 Flags is 0 NumberOfParameters is 0 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 1237 Detection location is 313 Flags is 0 NumberOfParameters is 0 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 10060 Detection location is 311 Flags is 0 NumberOfParameters is 3 Long val: 135 Pointer val: 0 Pointer val: 0 ProcessID is 5876 System Time is: 3/3/2011 2:44:12:822 Generating component is 8 Status is 10060 Detection location is 318 Flags is 0 NumberOfParameters is 0 I'm pretty sure that the exception number 1722 is the key but I can't find any info about it. There may be a firewall with ports that need opening between the machines which I am checking with our sys admins now. But I can do a regular ping between the machines. Other than that I am reading a lot of articles talking about OS services and components I know nothing about and am having trouble finding any info on. Can anyone shed any light on this? FYI the machine is running Windows Server 2003 RS SP2.

  Read the article

• How to diagnose a spontaneous reboot?

  - by Spectralist

  My computer reboots, seemingly completely at random, about once every week to two weeks but has occasionally gone months. It just goes from running fine to the POST with no error messages or anything and doesn't seem to be due to heat or usage as it's happened a couple of times when the computer has booted just a few moments ago and is idling. It's been happening for as long as I've had this computer, almost two years. It's happened in both Vista and Windows7. I strongly suspect it's a hardware problem. But due to the rareish and random nature of the crashes my normal strategy of just removing hardware until the problem stops isn't really practical. My guess would be Power Supply, Ram, or Motherboard. But I just don't know how to test an issue this random and want to figure out how to confirm which it is before I go replacing things. So is there some software or hardware that can be used to test these sorts of errors? I did run memtest86 for about 8 hours without finding any issues. And the power supply is more than capable of running my system.

  Read the article

• Protocol (or service publish/discovery) to detect devices in network

  - by Gobliins

  we connect some embedded devices in a network. What i am looking for now, is a way to find the devices IP and identify them. We work with Windows PC´s and i am about to write a C# tool that should do this. I thought about send a udp broadcast and in the ack i.e. is the device´s ip, which would mean the device needs a daemon runnig to assign an ip itself. Running a service (like a printer) on the device, and on the PC just lookup for the service. I read about some things like apipa, zeroconf, ipv4 local link, bonjour, dns-sd, mdns, bonjour; They can automatically assign ip´s and publish services in a network. My Question is, can someone recommend me what would be good for my task? -The protocol or Service should be low on ressource (memory/cpu usage) use. -Are there some standard protocolls to use? -Is DNS a good idea or would it be to ressource consumpting just for finding a device´s IP? -Should also work when no dhcp servers are around. edit: To clarify a bit: The IP configuration is automatic. The problem to focus is how to tell the PC which IP in the network (or a direct connection in this vase there would only be one) belongs to the device (identity).

  Read the article

• How to block access to addresses outside network (internet)

  - by devnull

  I have a homeserver, that is now connected to the internet with an own network device (ath0 - 192.168.1.x). It also has one more network interface (eth0 - 192.168.0.x). Soon I will get a second internet line that will be connected the second network. The server then has both networks with different internet lines available, but i only want it to connect to the internet on the old ath0 interface - not the new eth0 (192.168.0.x). Background of that constellation is that the new line has a volume-limit in traffic - the old hasn't and i need the new line for all mobile devices and laptops. The devices should be able to use the new network to connect to the internet and the server. The homeserver is a debian 6 with iptables and some already written rules for it. I need now a rule to block all outgoing internet access on the eth0 interface - i guess it could be something with --target != 192.168.0.0 but i did not succeed in finding the proper solution. Edit: found the solution: iptables -A OUTPUT -o eth0 -d 192.168.0.0/24 -m state --state NEW,ESTABLISHED -j ACCEPT With that setting, all traffic that uses the eth0 interface is only allowed if the destination is inside the network 192.168.0.x - all other traffic is denied .

  Read the article

< Previous Page | 458 459 460 461 462 463 464 465 466 467 468 469  | Next Page >