performance counters - Page 486

Virtualized data centre–Part three: Architecture

- by marc dekeyser

Having the basics (like discussed in the previous articles) is all good and well, but how do we get started on this?! It can be quite daunting after all! From my own point of view I can absolutely confirm your worries and concerns, but also tell you that it is not as hard as it seems! Deciding on what kind of motherboard to buy, processor and how much memory is an activity you will spend quite some time doing research on. And that is not even mentioning storage! All in all it comes down to setting you expectations and your budget. Probably adjusting your expectations according to your budget :). Processors As a rule of thumb you want VT-D (virtualization) technology built in to the processor allowing you to have 64 bit machines running on your host. Memory The more the better! If you are building a home lab don’t bother with ECC unless you are going to run machines that absolutely should be on all the time and your comfort depends on it! Motherboard Depends on what you are going to do with storage: If you are going the NAS way then the number of SATA port/RAID capabilities do not really matter. If you decide to have a single server with lots of dedicated storage it obviously matters how much SATA ports you will have, alternatively you could use a RAID controller (but these set you back a pretty penny if you want one. DELL 6i’s are usually available for a good bargain if you can find one!). Easiest is to get one with a built-in graphics card (on-board) as you are just adding more heat, power usage and possible points of failure. Networking Just like your choice of motherboard the networking side tends to depend on how you want to go. A single virtualization host with local storage can usually get away with having a single network card, a cluster or server which uses iSCSI storage tends to have more than one teamed up :). Storage The dreaded beast from the dark! The horror which lives in the forest! The most difficult decision you are going to make in the building of your lab. Why you might ask? Simple my friend, having the right choice of storage can make or break your virtualization solution. The performance of you storage choice will have an important impact on the responsiveness of your virtual machines and the deployment of new machines. It also makes a run with your budget! If you decide to go the NAS route you will be dropping a lot more money than if you would be having just a bunch of disks sitting in a server and manually distributing the virtual machines over the disks. Platform I’m a Microsoftee so Hyper-V is a dead giveaway for me. If you are interested in using VMware I won’t stop you but the rest of my posts will be oriented on Server 2012 Hyper-V (aka 3.0)! What did I use? Before someone asks me this in the comments I’ll give you a quick run down of what I am using. - Intel 2.4 quad core processors (i something something) - 24 GB DDR3 Memory - Single disk in each server (might look at this as I move the servers to 2012) - Synology DS1812+ NAS - 3 network interfaces where possible - HP1800 procurve managed switch I decided to spring for the NAS as I will also be using it for backups and media storage (which is working out quite nicely with my Xbox 360 I must say). At the time of building my 2 boxes (over a year and a half ago) these set me back about 900 euros each so I can image you can build the same or better for a lower price. Next article will be diagramming what I want to achieve and starting a build on the Hyper V 3.0 cluster!

Read the article

Mastering snow and Java development at jDays in Gothenburg

- by JavaCecilia

Last weekend, I took the train from Stockholm to Gothenburg to attend and present at the new Java developer conference jDays. It was professionally arranged in the Swedish exhibition hall close to the amusement park Liseberg and we got a great deal out of the top-level presenters and hallway discussions. Understanding and Improving Your Java Process Our main purpose was to spread information on JVM and our monitoring tools for Java processes, so I held a crash course in the most important terms and concepts if you want to affect the performance of your Java process. From the beginning - the JVM specification to interpretation of heap usage graphs. For correct analysis, you also need to understand something about process memory - you need space for the Java heap (-Xms for initial size and -Xmx for max heap size), but the process memory also contain the thread stacks (to a size of -Xss), JVM internal data structures used for keeping track of Java objects on the heap, method compilation/optimization, native libraries, etc. If you get long pause times, make sure to monitor your application, see the allocation rate and frequency of pause times.My colleague Klara Ward then held a presentation on the Java Mission Control product, the profiling and diagnostics tools suite for HotSpot, coming soon. The room was packed and very appreciated, Klara demonstrated four different scenarios, e.g. how to diagnose and fix latencies due to lock contention for logging.My German colleague, OpenJDK ambassador Dalibor Topic travelled to Sweden to do the second keynote on "Make the Future Java". He let us in on the coming features and roadmaps of Java, now delivering major versions on a two-year schedule (Java 7 2011, Java 8 2013, etc). Also letting us in on where to download early versions of 8, to report problems early on. Software Development in teams Being a scout leader, I'm drilled in different team building and workshop techniques, creating strong groups - of course, I had to attend Henrik Berglund's session on building successful teams. He spoke about the importance of clear goals, autonomy and agreed processes. Thomas Sundberg ended the conference by doing live remote pair programming with Alex in Rumania and a concrete tips for people wanting to try it out (for local collaboration, remember to wash and change clothes). Memory Master Keynote The conference keynote was delivered by the Swedish memory master Mattias Ribbing, showing off by remembering the order of a deck of cards he'd seen once. He made it interactive by forcing the audience to learn a memory mastering technique of remembering ten ordered things by heart, asking us to shout out the order backwards and we made it! I desperately need this - bought the book, will get back on the subject. Continuous Delivery The most impressive presenter was Axel Fontaine on Continuous Delivery. Very well prepared slides with key images of his message and moved about the stage like a rock star. The topic is of course highly interesting, how to create an infrastructure enabling immediate feedback to developers and ability to release your product several times per day. Tomek Kaczanowski delivered a funny and useful presentation on good and bad tests, providing comic relief with poorly written tests and the useful rules of thumb how to rewrite them. To conclude, we had a great time and hope to see you at jDays next year :)

Read the article

SharePoint For Newbie Developers: Code Scope

- by Mark Rackley

So, I continue to try to come up with diagrams and information to help new SharePoint developers wrap their heads around this SharePoint beast, especially when those newer to development are on my team. To that end, I drew up the below diagram to help some of our junior devs understand where/when code is being executed in SharePoint at a high level. Note that I say “High Level”… This is a simplistic diagram that can get a LOT more complicated if you want to dive in deeper. For the purposes of my lesson it served its purpose well. So, please no comments from you peanut gallery about information 3 levels down that’s missing unless it adds to the discussion. Thanks So, the diagram below details where code is executed on a page load and gives the basic flow of the page load. There are actually many more steps, but again, we are staying high level here. I just know someone is still going to say something like “Well.. actually… the dlls are getting executed when…” Anyway, here’s the diagram with some information I like to point out: Code Scope / Where it is executed So, looking at the diagram we see that dlls and XSL are executed on the server and that JavaScript/jQuery are executed on the client. This is the main thing I like to point out for the following reasons: XSL (for the most part) is faster than JavaScript I actually get this question a lot. Since XSL is executed on the server less data is getting passed over the wire and a beefier machine (hopefully) is doing the processing. The outcome of course is better performance. When You are using jQuery and making Web Service calls you are building XML strings and sending them to the server, then ALL the results come back and the client machine has to parse through the XML and use what it needs and ignore the rest (and there is a lot of garbage that comes back from SharePoint Web Service calls). XSL and JavaScript cannot work together in the same scope Let me clarify. JavaScript can send data back to SharePoint in postbacks that XSL can then use. XSL can output JavaScript and initiate JavaScript variables. However, XSL cannot call a JavaScript method to get a value and JavaScript cannot directly interact with XSL and call its templates. They are executed in there scope only. No crossing of boundaries here. So, what does this all mean? Well, nothing too deep. This is just some basic fundamental information that all SharePoint devs need to understand. It will help you determine what is the best solution for your specific development situation and it will help the new guys understand why they get an error when trying to call a JavaScript Function from within XSL. Let me know if you think quick little blogs like this are helpful or just add to the noise. I could probably put together several more that are similar. As always, thanks for stopping by, hope you learned something new.

Read the article

Designing An ACL Based Permission System

- by ryanzec

I am trying to create a permissions system where everything is going to be stored in MySQL (or some database) and pulled using PHP for a project management system I am building. I am right now trying to do it is an ACL kind of way. There are a number key features I want to be able to support: 1. Being able to assign permissions without being tied to a specific object. The reason for this is that I want to be able to selectively show/hide elements of the UI based on permissions at a point where I am not directly looking at a domain object instance. For instance, a button to create a new project should only should only be shown to users that have the pm.project.create permission but obviously you can assign a create permission to an domain object instance (as it is already created). 2. Not have to assign permissions for every single object. Obviously creating permissions entries for every single object (projects, tickets, comments, etc…) would become a nightmare to maintain so I want to have some level of permission inheritance. *3. Be able to filter queries based on permissions. This would be a really nice to have but I am not sure if it is possible. What I mean by this is say I have a page that list all projects. I want the query that pulls all projects to incorporate the ACL so that it would not show projects that the current user does not have pm.project.read access to. This would have to be incorporated into the main query as if it is a process that is done after that main query (which I know I could do) certain features like pagination become much more difficult. Right now this is my basic design for the tables: AclEntities id - the primary key key - the unique identifier for the domain object (usually the primary key of that object) parentId - the parent of the domain object (like the project object if this was a ticket object) aclDomainObjectId - metadata about the domain object AclDomainObjects id - primary key title - simple string to unique identify the domain object(ie. project, ticket, comment, etc…) fullyQualifiedClassName - the fully qualified class name for use in code (I am using namespaces) There would also be tables mapping AclEntities to Users and UserGroups. I also have this interface that all acl entity based object have to implement: IAclEntity getAclKey() - to the the unique key for this specific instance of the acl domain object (generally return the primary key or a concatenated string of a composite primary key) getAclTitle() - to get the unique title for the domain object (generally just returning a static string) getAclDisplayString() - get the string that represents this entity (generally one or more field on the object) getAclParentEntity() - get the parent acl entity object (or null if no parent) getAclEntity() - get the acl enitty object for this instance of the domain object (or null if one has not been created yet) hasPermission($permissionString, $user = null) - whether or not the user has the permission for this instance of the domain object static getFromAclEntityId($aclEntityId) - get a specific instance of the domain object from an acl entity id. Do any of these features I am looking for seems hard to support or are just way off base? Am I missing or not taking in account anything in my implementation? Is performance something I should keep in mind?

Read the article

Call For Papers Tips and Tricks

- by speakjava

This year's JavaOne session review has just been completed and by now everyone who submitted papers should know whether they were successful or not. I had the pleasure again this year of leading the review of the 'JavaFX and Rich User Experiences' track. I thought it would be useful to write up a few comments to help people in future when submitting session proposals, not just for JavaOne, but for any of the many developer conferences that run around the world throughout the year. This also draws on conversations I recently had with various Java User Group leaders at the Oracle User Group summit in Riga. Many of these leaders run some of the biggest and most successful Java conferences in Europe. Try to think of a title which will sound interesting. For example, "Experiences of performance tuning embedded Java for an ARM architecture based single board computer" probably isn't going to get as much attention as "Do you like coffee with your dessert? Java on the Raspberry Pi". When thinking of the subject and title for your talk try to steer clear of sessions that might be too generic (and so get lost in a group of similar sessions). Introductory talks are great when the audience is new to a subject, but beware of providing sessions that are too basic when the technology has been around for a while and there are lots of tutorials already available on the web. JavaOne, like many other conferences has a number of fields that need to be filled in when submitting a paper. Many of these are selected from pull-down lists (like which track the session is applicable to). Check these lists carefully. A number of sessions we had needed to be shuffled between tracks when it was thought that the one selected was not appropriate. We didn't count this against any sessions, but it's always a good idea to try and get the right one from the start, just in case. JavaOne, again like many other conferences, has two fields that describe the session being submitted: abstract and summary. These are the most critical to a successful submission. The two fields have different names and that is significant; a frequent mistake people make is to write an abstract for a session and then duplicate it for the summary. The abstract (at least in the case of JavaOne) is what gets printed in the show guide and is typically what will be used by attendees when deciding what sessions to attend. This is where you need to sell your session, not just to the reviewers, but also the people who you want in your audience. Submitting a one line abstract (unless it's a really good one line) is not usually enough to decide whether this is worth investing an hour of conference time. The abstract typically has a limit of a few hundred characters. Try to use as many of them as possible to get as much information about your session across. The summary should be different from the abstract (and don't leave it blank as some people do). This field is where you can give the reviewers more detail about things like the structure of the talk, possible demonstrations and so on. As a reviewer I look to this section to help me decide whether the hard-sell of the title and abstract will actually be reflected in the final content. Try to make this comprehensive, but don't make it excessively long. When you have to review possibly hundreds of sessions a certain level of conciseness can make life easier for reviewers and help the cause of your session. If you've not made many submissions for talks in the past, or if this is your first, try to give reviewers places to find background on you as a presenter. Having an active blog and Twitter handle can also help reviewers if they're not sure what your level of expertise is. Many call-for-papers have places for you to include this type of information. It's always good to have new and original presenters and presentations for conferences. Hopefully these tips will help you be successful when you answer the next call-for-papers.

Read the article

how to write the code for this program specially in mathematica? [closed]

- by asd

I implemented a solution to the problem below in Mathematica, but it takes a very long time (hours) to compute f of kis or the set B for large numbers. Somebody suggested that implementing this in C++ resulted in a solution in less than 10 minutes. Would C++ be a good language to learn to solve these problems, or can my Mathematica code be improved to fix the performance issues? I don't know anything about C or C++ and it should be difficult to start to learn this languages. I prefer to improve or write new code in mathematica. Problem Description Let $f$ be an arithmetic function and A={k1,k2,...,kn} are integers in increasing order. Now I want to start with k1 and compare f(ki) with f(k1). If f(ki)f(k1), put ki as k1. Now start with ki, and compare f(kj) with f(ki), for ji. If f(kj)f(ki), put kj as ki, and repeat this procedure. At the end we will have a sub sequence B={L1,...,Lm} of A by this property: f(L(i+1))f(L(i)), for any 1<=i<=m-1 For example, let f is the divisor function of integers. Here I put some part of my code and this is just a sample and the question in my program could be more larger than these: «««««««««««««««««««««««««««««««««««« f[n_] := DivisorSigma[0, n]; g[n_] := Product[Prime[i], {i, 1, PrimePi[n]}]; k1 = g[67757] g[353] g[59] g[19] g[11] g[7] g[5]^2 6^3 2^7; k2 = g[67757] g[353] g[59] g[19] g[11] g[7] g[5] 6^5 2^7; k3 = g[67757] g[359] g[53] g[19] g[11] g[7] g[5] 6^4 2^7; k4 = g[67759] g[349] g[53] g[19] g[11] g[7] g[5] 6^5 2^6; k5 = g[67757] g[359] g[53] g[19] g[11] g[7] g[5] 6^4 2^8; k6 = g[67759] g[349] g[53] g[19] g[11] g[7] g[5]^2 6^3 2^7; k7 = g[67757] g[359] g[53] g[19] g[11] g[7] g[5] 6^5 2^6; k8 = g[67757] g[359] g[53] g[19] g[11] g[7] g[5] 6^4 2^9; k9 = g[67757] g[359] g[53] g[19] g[11] g[7] g[5]^2 6^3 2^7; k10 = g[67757] g[359] g[53] g[19] g[11] g[7] g[5] 6^5 2^7; k11 = g[67759] g[349] g[53] g[19] g[11] g[7] g[5]^2 6^4 2^6; k12 = g[67757] g[359] g[53] g[19] g[11] g[7] g[5]^2 6^3 2^8; k13 = g[67757] g[359] g[53] g[19] g[11] g[7] g[5]^2 6^4 2^6; k14 = g[67757] g[359] g[53] g[19] g[11] g[7] g[5]^2 6^3 2^9; k15 = g[67757] g[359] g[53] g[19] g[11] g[7] g[5]^2 6^4 2^7; k16 = g[67757] g[359] g[53] g[23] g[11] g[7] g[5] 6^4 2^8; k17 = g[67757] g[359] g[59] g[19] g[11] g[7] g[5] 6^4 2^7; k18 = g[67757] g[359] g[53] g[23] g[11] g[7] g[5] 6^4 2^9; k19 = g[67759] g[353] g[53] g[19] g[11] g[7] g[5] 6^4 2^6; k20 = g[67763] g[347] g[53] g[19] g[11] g[7] g[5] 6^4 2^7; k = Table[k1, k2, k3, k4, k5, k6, k7, k8, k9, k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k20]; i = 1; count = 0; For[j = i, j <= 20, j++, If[f[k[[j]]] - f[k[[i]]] > 0, i = j; Print["k",i]; count = count + 1]]; Print["count= ", count] ««««««««««««««««««««««««««««««««««««

Read the article

Welcome To The Nashorn Blog

- by jlaskey

Welcome to all. Time to break the ice and instantiate The Nashorn Blog. I hope to contribute routinely, but we are very busy, at this point, preparing for the next development milestone and, of course, getting ready for open source. So, if there are long gaps between postings please forgive. We're just coming back from JavaOne and are stoked by the positive response to all the Nashorn sessions. It was great for the team to have the front and centre slide from Georges Saab early in the keynote. It seems we have support coming from all directions. Most of the session videos are posted. Check out the links. Nashorn: Optimizing JavaScript and Dynamic Language Execution on the JVM. Unfortunately, Marcus - the code generation juggernaut, got saddled with the first session of the first day. Still, he had a decent turnout. The talk focused on issues relating to optimizations we did to get good performance from the JVM. Much yet to be done but looking good. Nashorn: JavaScript on the JVM. This was the main talk about Nashorn. I delivered the little bit of this and a little bit of that session with an overview, a follow up on the open source announcement, a run through a few of the Nashorn features and some demos. The room was SRO, about 250±. High points: Sam Pullara, from Twitter, came forward to describe how painless it was to get Mustache.js up and running (20x over Rhino), and, John Ceccarelli, from NetBeans came forward to describe how Nashorn has become an integral part of Netbeans. A healthy Q & A at the end was very encouraging. Meet the Nashorn JavaScript Team. Michel, Attila, Marcus and myself hosted a Q & A. There was only a handful of people in the room (we assume it was because of a conflicting session ;-) .) Most of the questions centred around Node.jar, which leads me to believe, Nashorn + Node.jar is what has the most interest. Akhil, Mr. Node.jar, sitting in the audience, fielded the Node.jar questions. Nashorn, Node, and Java Persistence. Doug Clarke, Akhil and myself, discussed the title topics, followed by a lengthy Q & A (security had to hustle us out.) 80 or so in the room. Lots of questions about Node.jar. It was great to see Doug's use of Nashorn + JPA. Nashorn in action, with such elegance and grace. Putting the Metaobject Protocol to Work: Nashorn’s Java Bindings. Attila discussed how he applied Dynalink to Nashorn. Good turn out for this session as well. I have a feeling that once people discover and embrace this hidden gem, great things will happen for all languages running on the JVM. Finally, there were quite a few JavaOne sessions that focused on non-Java languages and their impact on the JVM. I've always believed that one's tool belt should carry a variety of programming languages, not just for domain/task applicability, but also to enhance your thinking and approaches to problem solving. For the most part, future blog entries will focus on 'how to' in Nashorn, but if you have any suggestions for topics you want discussed, please drop a line. Cheers.

Read the article

Strategies for invoking subclass methods on generic objects

- by Brad Patton

I've run into this issue in a number of places and have solved it a bunch of different ways but looking for other solutions or opinions on how to address. The scenario is when you have a collection of objects all based off of the same superclass but you want to perform certain actions based only on instances of some of the subclasses. One contrived example of this might be an HTML document made up of elements. You could have a superclass named HTMLELement and subclasses of Headings, Paragraphs, Images, Comments, etc. To invoke a common action across all of the objects you declare a virtual method in the superclass and specific implementations in all of the subclasses. So to render the document you could loop all of the different objects in the document and call a common Render() method on each instance. It's the case where again using the same generic objects in the collection I want to perform different actions for instances of specific subclass (or set of subclasses). For example (an remember this is just an example) when iterating over the collection, elements with external links need to be downloaded (e.g. JS, CSS, images) and some might require additional parsing (JS, CSS). What's the best way to handle those special cases. Some of the strategies I've used or seen used include: Virtual methods in the base class. So in the base class you have a virtual LoadExternalContent() method that does nothing and then override it in the specific subclasses that need to implement it. The benefit being that in the calling code there is no object testing you send the same message to each object and let most of them ignore it. Two downsides that I can think of. First it can make the base class very cluttered with methods that have nothing to do with most of the hierarchy. Second it assumes all of the work can be done in the called method and doesn't handle the case where there might be additional context specific actions in the calling code (i.e. you want to do something in the UI and not the model). Have methods on the class to uniquely identify the objects. This could include methods like ClassName() which return a string with the class name or other return values like enums or booleans (IsImage()). The benefit is that the calling code can use if or switch statements to filter objects to perform class specific actions. The downside is that for every new class you need to implement these methods and can look cluttered. Also performance could be less than some of the other options. Use language features to identify objects. This includes reflection and language operators to identify the objects. For example in C# there is the is operator that returns true if the instance matches the specified class. The benefit is no additional code to implement in your object hierarchy. The only downside seems to be the lack of using something like a switch statement and the fact that your calling code is a little more cluttered. Are there other strategies I am missing? Thoughts on best approaches?

Read the article

Best triple head display setup

- by dgel

I'm currently running Ubuntu 12.04 with a darn good triple head display setup. I've got a VisionTek 900530 Radeon HD 5450 512MB DDR3 PCI Express video card that has two DVI outputs and one Mini DisplayPort that I have connected to a HDMI adapter. I'm running three identical Asus 1920x1080 monitors that each have a DVI, VGA, and HDMI input. I'm using the xorg-edgers ppa, so I'm using the open source radeon driver version 6.99.99. I tried using the ATI binary fglrx driver, but I wasn't able to get the three monitors working properly- the monitor connected via HDMI / DisplayPort wouldn't run at full resolution. The setup is almost perfect: Compiz runs fine and is quite snappy. I'm not able to use that great compiz feature where you can drag a window to the side of a display and it will half maximize. I occasionally experience display corruption weirdness with Unity and need to restart it. When I use a dropdown menu in LibreOffice it often pops the menu down in another window. For example, if I'm using the center monitor and click the Insert menu, the menu pulls down on the monitor to my right, forcing me to chase it. If I chase down the menu and choose Manual Break, the dialog appears over on my left monitor. This absurdity is mildly entertaining but has lost its novelty. I've decided to build a new system and have spared no expense- latest i7 processor, SSD, etc. I really like the performance of the Nvidia binary drivers, so I put two ZOTAC ZT-40707-10L GeForce GT 440 in the system, figuring I'd have four DVI outputs and an awesome triple (or even eventually quad) head setup. Unfortunately it appears that I didn't do sufficient research before my purchase. It seems that Nvidia TwinView only supports two monitors on one card (I guess that's why they call it TwinView...). I messed around with running two X servers, but I really don't want that- being able to drag windows to any monitor is critical. It doesn't sound like Xinerama is an option because from what I understand it simply doesn't support Compiz. I've seen a BaseMosaic option that can be used with the Nvidia drivers that appears to support an almost unlimited number of heads- unfortunately me cheap little cards don't support it. I'm also not sure whether you'll still have all nice maximizing and snapping that TwinView provides, or whether Ubuntu will only see it as one massive display. I put my old trusty ATI card into my new system and installed 12.10. I'm using the opensource radeon drivers again because even in 12.10 I can't get the fglrx binary drivers to do triple head. Unfortunately, even with an unbelievably powerful system the experience is extremely sluggish (much more so than my experience in 12.04). The menu scattering problem appears to be fixed, but I get a lot of nasty Unity display corruption. So finally, my question is this: What hardware / drivers should I use? I'm willing to buy (almost) any video card(s). I have two PCI-Express 3.0 slots on my motherboard (which has an integrated Intel HD card). I'm willing to use ATI or Nvidia cards and willing to run Ubuntu 12.04.1 or 12.10. I'm not a gamer, but do want beautiful and snappy Compiz effects. Does anyone out there have the perfect triple head setup in 12.04 or 12.10? What hardware / drivers are you using? I have those two Nvidia cards but will probably be returning them unless someone knows a way to use them together for a triple head setup. Since I'm having pretty good luck with a single ATI card providing three displays, should I just buy a beefier one with the hopes that it will fix the horrible sluggishness I'm experiencing in 12.10?

Read the article

Minimum team development sizes

- by MarkPearl

Disclaimer - these are observations that I have had, I am not sure if this follows the philosophy of scrum, agile or whatever, but most of these insights were gained while implementing a scrum scenario. Two is a partnership, three starts a team For a while I thought that a team was anything more than one and that scrum could be effective methodology with even two people. I have recently adjusted my thinking to a scrum team being a minimum of three, so what happened to two and what do you call it? For me I consider a group of two people working together a partnership - there is value in having a partnership, but some of the dynamics and value that you get from having a team is lost with a partnership. Avoidance of a one on one confrontation The first dynamic I see missing in a partnership is the team motivation to do better and how this is delivered to individuals that are not performing. Take two highly motivated individuals and put them together and you will typically see them continue to perform. Now take a situation where you have two individuals, one performing and one not and the behaviour is totally different compared to a team of three or more individuals. With two people, if one feels the other is not performing it becomes a one on one confrontation. Most people avoid confrontations and so nothing changes. Compare this to a situation where you have three people in a team, 2 performing and 1 not the dynamic is totally different, it is no longer a personal one on one confrontation but a team concern and people seem more willing to encourage the individual not performing and express their dissatisfaction as a team if they do not improve. Avoiding the effects of Tuckman’s Group Development Theory If you are not familiar with Tuckman’s group development theory give it a read (http://en.wikipedia.org/wiki/Tuckman's_stages_of_group_development) In a nutshell with Tuckman’s theory teams go through these stages of Forming, Storming, Norming & Performing. You want your team to reach and remain in the Performing stage for as long as possible - this is where you get the most value. When you have a partnership of two and you change the individuals in the partnership you basically do a hard reset on the partnership and go back to the beginning of Tuckman’s model each time. This has a major effect on the performance of a team and what they can deliver. What I have seen is that you reduce the effects of Tuckman's theory the more individuals you have in the team (until you hit the maximum team size in which other problems kick in). While you will still experience Tuckman's theory with a team of three, the impact will be greatly reduced compared to two where it is guaranteed every time a change occurs. It's not just in the numbers, it's in the people One final comment - while the actual numbers of a team do play a role, the individuals in the team are even more important - ideally you want to keep individuals working together for an extended period. That doesn't mean that you never change the individuals in a team, or that once someone joins a team they are stuck there - there is value in an individual moving from team to team and getting cross pollination, but the period of time that an individual moves should be in month's or years, not days or weeks. Why? So why is it important to know this? Why is it important to know how a team works and what motivates them? I have been asking myself this question for a while and where I am at right now is this… the aim is to achieve the stage where the sum of the total (team) is greater than the sum of the parts (team members). This is why we form teams and why understanding how they work is a challenge and also extremely stimulating.

Read the article

BI&EPM in Focus Sep 2012

- by Mike.Hallett(at)Oracle-BI&EPM

Customers · Iluka Resources Improves Business Insight into Mining Operations Through Significantly Faster, Customized Analyses · Waikato Regional Council Consolidates Financial Reports up to 10 Times Faster · Lojas Renner Shortens Budget Consolidation from Three Days to 15 Minutes; Improves Data Quality, and Supports Aggressive Expansion Plans · Link to Complete Archive · Profit Magazine article featuring General Dynamics: RECONnomics: Integrate. Innovate. Grow (link) · Video: Goodhope Asia Unifies Financial Data with Oracle Hyperion (link) Enterprise Performance Management · Oracle University Training on Demand: 1. Oracle Hyperion Financial Reporting 11.1.2 for Financial Management (link) 2. Oracle Essbase Bootcamp: On Demand (link) 3. Oracle Hyperion Planning 11.1.2: Create & Manage Applications On Demand (link) Business Intelligence · Oracle University Training on Demand: 1. Learn How to Create Analyses, Dashboards with OBI 11g (link) 2. Build Repositories with Oracle Business Intelligence 11g (link) 3. Oracle BI Publisher 11g Fundamentals (link) 4. Oracle BI Applications Courses now available for 7.9.6 (link) 5. Oracle BI 11g: New Features and Exalytics · Oracle Business Intelligence Release 11.1.1.6.2BP, updated information: 1. Oracle BI Mobile at the Speed of Thought 2. What's New in Oracle Business Intelligence Mobile 3. What's New in Oracle Business Intelligence Visualizations 4. Oracle Business Intelligence on Oracle.com 5. Download the New Release · Discover How to Turn Data into Insight: Big Data Guide : Whitepaper and set of short Videos. · New OPN Specialisation Exam for OBI 11g Certification . · Lastest BIC2g and Exalytics Demonstration VMs for Partners . · New Version 2.3 Oracle Endeca Information Discovery and Server now available . · New Oracle BI Publisher 11.1.1.6 Trial Edition Now Available .

Read the article

libgdx draw issue and animation

- by johnny-b

it seems as though i cannot get the draw method to work??? it seems as though the bullet.draw(batcher) does not work and i cannot understand why as the bullet is a sprite. i have made a Sprite[] and added them as animation. could that be it? i tried batcher.draw(AssetLoader.bulletAnimation.getKeyFrame(runTime), bullet.getX(), bullet.getY(), bullet.getOriginX() / 2, bullet.getOriginY() / 2, bullet.getWidth(), bullet.getHeight(), 1, 1, bullet.getRotation()); but that dont work, the only way it draws is this batcher.draw(AssetLoader.bulletAnimation.getKeyFrame(runTime), bullet.getX(), bullet.getY()); below is the code. // this is in a Asset Class texture = new Texture(Gdx.files.internal("SpriteN1.png")); texture.setFilter(TextureFilter.Nearest, TextureFilter.Nearest); bullet1 = new Sprite(texture, 380, 350, 45, 20); bullet1.flip(false, true); bullet2 = new Sprite(texture, 425, 350, 45, 20); bullet2.flip(false, true); Sprite[] bullets = { bullet1, bullet2 }; bulletAnimation = new Animation(0.06f, bullets); bulletAnimation.setPlayMode(Animation.PlayMode.LOOP); // this is the GameRender class public class GameRender() { private Bullet bullet; private Ball ball; public GameRenderer(GameWorld world) { myWorld = world; cam = new OrthographicCamera(); cam.setToOrtho(true, 480, 320); batcher = new SpriteBatch(); // Attach batcher to camera batcher.setProjectionMatrix(cam.combined); shapeRenderer = new ShapeRenderer(); shapeRenderer.setProjectionMatrix(cam.combined); // Call helper methods to initialize instance variables initGameObjects(); initAssets(); } private void initGameObjects() { ball = GameWorld.getBall(); bullet = myWorld.getBullet(); scroller = myWorld.getScroller(); } private void initAssets() { ballAnimation = AssetLoader.ballAnimation; bulletAnimation = AssetLoader.bulletAnimation; } public void render(float runTime) { Gdx.gl.glClearColor(0, 0, 0, 1); Gdx.gl.glClear(GL30.GL_COLOR_BUFFER_BIT); batcher.begin(); // Disable transparency // This is good for performance when drawing images that do not require // transparency. batcher.disableBlending(); // The ball needs transparency, so we enable that again. batcher.enableBlending(); batcher.draw(AssetLoader.ballAnimation.getKeyFrame(runTime), ball.getX(), ball.getY(), ball.getWidth(), ball.getHeight()); batcher.draw(AssetLoader.bulletAnimation.getKeyFrame(runTime), bullet.getX(), bullet.getY()); // End SpriteBatch batcher.end(); } } // this is the gameworld class public class GameWorld { public static Ball ball; private Bullet bullet; private ScrollHandler scroller; public GameWorld() { ball = new Ball(480, 273, 32, 32); bullet = new Bullet(10, 10); scroller = new ScrollHandler(0); } public void update(float delta) { ball.update(delta); bullet.update(delta); scroller.update(delta); } public static Ball getBall() { return ball; } public ScrollHandler getScroller() { return scroller; } public Bullet getBullet() { return bullet; } } is there anyway so make the sprite work?

Read the article

Multithreading 2D gravity calculations

- by Postman

I'm building a space exploration game and I've currently started working on gravity ( In C# with XNA). The gravity still needs tweaking, but before I can do that, I need to address some performance issues with my physics calculations. This is using 100 objects, normally rendering 1000 of them with no physics calculations gets well over 300 FPS (which is my FPS cap), but any more than 10 or so objects brings the game (and the single thread it runs on) to its knees when doing physics calculations. I checked my thread usage and the first thread was killing itself from all the work, so I figured I just needed to do the physics calculation on another thread. However when I try to run the Gravity.cs class's Update method on another thread, even if Gravity's Update method has nothing in it, the game is still down to 2 FPS. Gravity.cs public void Update() { foreach (KeyValuePair<string, Entity> e in entityEngine.Entities) { Vector2 Force = new Vector2(); foreach (KeyValuePair<string, Entity> e2 in entityEngine.Entities) { if (e2.Key != e.Key) { float distance = Vector2.Distance(entityEngine.Entities[e.Key].Position, entityEngine.Entities[e2.Key].Position); if (distance > (entityEngine.Entities[e.Key].Texture.Width / 2 + entityEngine.Entities[e2.Key].Texture.Width / 2)) { double angle = Math.Atan2(entityEngine.Entities[e2.Key].Position.Y - entityEngine.Entities[e.Key].Position.Y, entityEngine.Entities[e2.Key].Position.X - entityEngine.Entities[e.Key].Position.X); float mult = 0.1f * (entityEngine.Entities[e.Key].Mass * entityEngine.Entities[e2.Key].Mass) / distance * distance; Vector2 VecForce = new Vector2((float)Math.Cos(angle), (float)Math.Sin(angle)); VecForce.Normalize(); Force = Vector2.Add(Force, VecForce * mult); } } } entityEngine.Entities[e.Key].Position += Force; } } Yeah, I know. It's a nested foreach loop, but I don't know how else to do the gravity calculation, and this seems to work, it's just so intensive that it needs its own thread. (Even if someone knows a super efficient way to do these calculations, I'd still like to know how I COULD do it on multiple threads instead) EntityEngine.cs (manages an instance of Gravity.cs) public class EntityEngine { public Dictionary<string, Entity> Entities = new Dictionary<string, Entity>(); public Gravity gravity; private Thread T; public EntityEngine() { gravity = new Gravity(this); } public void Update() { foreach (KeyValuePair<string, Entity> e in Entities) { Entities[e.Key].Update(); } T = new Thread(new ThreadStart(gravity.Update)); T.IsBackground = true; T.Start(); } } EntityEngine is created in Game1.cs, and its Update() method is called within Game1.cs. I need my physics calculation in Gravity.cs to run every time the game updates, in a separate thread so that the calculation doesn't slow the game down to horribly low (0-2) FPS. How would I go about making this threading work? (any suggestions for an improved Planetary Gravity system are welcome if anyone has them) I'm also not looking for a lesson in why I shouldn't use threading or the dangers of using it incorrectly, I'm looking for a straight answer on how to do it. I've already spent an hour googling this very question with little results that I understood or were helpful. I don't mean to come off rude, but it always seems hard as a programming noob to get a straight meaningful answer, I usually rather get an answer so complex I'd easily be able to solve my issue if I understood it, or someone saying why I shouldn't do what I want to do and offering no alternatives (that are helpful). Thank you for the help!

Read the article

SQL to select random mix of rows fairly [migrated]

- by Matt Sieker

Here's my problem: I have a set of tables in a database populated with data from a client that contains product information. In addition to the basic product information, there is also information about the manufacturer, and categories for those products (a product can be in one or more categories). These categories are then referred to as "Product Categories", and which stores these products are available at. These tables are updated once a week from a feed from the customer. Since for our purposes, some of the product categories are the same, or closely related for our purposes, there is another level of categories called "General Categories", a general category can have one or more product categories. For the scope of these tables, here's some rough numbers: Data Tables: Products: 475,000 Manufacturers: 1300 Stores: 150 General Categories: 245 Product Categories: 500 Mapping Tables: Product Category -> Product: 655,000 Stores -> Products: 50,000,000 Now, for the actual problem: As part of our software, we need to select n random products, given a store and a general category. However, we also need to ensure a good mix of manufacturers, as in some categories, a single manufacturer dominates the results, and selecting rows at random causes the results to strongly favor that manufacturer. The solution that is currently in place, works for most cases, involves selecting all of the rows that match the store and category criteria, partition them on manufacturer, and include their row number from within their partition, then select from that where the row number for that manufacturer is less than n, and use ROWCOUNT to clamp the total rows returned to n. This query looks something like this: SET ROWCOUNT 6 select p.Id, GeneralCategory_Id, Product_Id, ISNULL(m.DisplayName, m.Name) AS Vendor, MSRP, MemberPrice, FamilyImageName from (select p.Id, gc.Id GeneralCategory_Id, p.Id Product_Id, ctp.Store_id, Manufacturer_id, ROW_NUMBER() OVER (PARTITION BY Manufacturer_id ORDER BY NEWID()) AS 'VendorOrder', MSRP, MemberPrice, FamilyImageName from GeneralCategory gc inner join GeneralCategoriesToProductCategories gctpc ON gc.Id=gctpc.GeneralCategory_Id inner join ProductCategoryToProduct pctp on gctpc.ProductCategory_Id = pctp.ProductCategory_Id inner join Product p on p.Id = pctp.Product_Id inner join StoreToProduct ctp on p.Id = ctp.Product_id where gc.Id = @GeneralCategory and ctp.Store_id=@StoreId and p.Active=1 and p.MemberPrice >0) p inner join Manufacturer m on m.Id = p.Manufacturer_id where VendorOrder <=6 order by NEWID() SET ROWCOUNT 0 (I've tried to somewhat format it to make it cleaner, but I don't think it really helps) Running this query with an execution plan shows that for the majority of these tables, it's doing a Clustered Index Seek. There are two operations that take up roughly 90% of the time: Index Seek (Nonclustered) on StoreToProduct: 17%. This table just contains the key of the store, and the key of the product. It seems that NHibernate decided not to make a composite key when making this table, but I'm not concerned about this at this point, as compared to the other seek... Clustered Index Seek on Product: 69%. I really have no clue how I could make this one more performant. On categories without a lot of products, performance is acceptable (<50ms), however larger categories can take a few hundred ms, with the largest category taking 3s (which has about 170k products). It seems I have two ways to go from this point: Somehow optimize the existing query and table indices to lower the query time. As almost every expensive operation is already a clustered index scan, I don't know what could be done there. The inner query could be tuned to not return all of the possible rows for that category, but I am unsure how to do this, and maintain the requirements (random products, with a good mix of manufacturers) Denormalize this data for the purpose of this query when doing the once a week import. However, I am unsure how to do this and maintain the requirements. Does anyone have any input on either of these items?

Read the article

Oracle ZS3 Contest for Partners: Share an unforgettable experience at the Teatro Alla Scala in Milan

- by Claudia Caramelli-Oracle

12.00 Dear valued Partner, We are pleased to launch a partner contest exclusive to our partners dedicated to promoting and selling Oracle Systems! You are essential to the success of Oracle and we want to recognize your contribution and effort in driving Oracle Storage to the market. To show our appreciation we are delighted to announce a contest, giving the winners the opportunity to attend a roundtable chaired by Senior Oracle Executives and spend an unforgettable evening at the magnificent Teatro Alla Scala in Milan, followed by a stay at the Grand Hotel et de Milan, courtesy of Oracle. Recognition will be given to 12 partner companies (10 VARs & 2 VADs) who will be recognized for their ZFS storage booking achievement in the broad market between June 1st and July 18th 2014. Criteria of Eligibility A minimum deal value of $30k is required for qualification Partners who are wholly or partially owned by a public sector organization are not eligible for participation Winners The winning VARs will be: The highest ZS3 or ZBA bookings achievers by COB on July 18th, 2014 in each Oracle EMEA region (1) The highest Oracle on Oracle (2) ZS3 or ZBA bookings achievers by COB on July 18th, 2014 in each Oracle EMEA region The winning VADs (3) will be: The highest ZS3 or ZBA bookings achiever by COB on July 18th 2014 in EMEA The highest Oracle on Oracle (2) ZS3 or ZBA bookings achiever by COB on July 18th 2014 in EMEA The Prize Winners will be invited to participate to a roundtable chaired by Oracle on Monday September 8th 2014 in Milan and to be guests of Oracle in the evening of September 8th, 2014 at the Teatro Alla Scala. The evening will comprise of a private tour of the Scala museum, cocktail reception at the elegant museum rooms and attending the performance by the renowned Soprano, Maria Agresta. Our guests will then retire for the evening to the Grand Hotel et de Milan, courtesy of Oracle. Oracle shall be the final arbiter in selecting the winners and all winners will be notified via their Oracle account manager.Full details about the contest, expenses covered by Oracle and timetable of events can be found on the Oracle EMEA Hardware (Servers & Storage) Partner Community workspace (FY15 Q1 ZFS Partner Contest). Remember: access to the community workspace requires membership. If you are not a member please register here. Good Luck!! For more information, please contact Sasan Moaveni. (1) Two VAR winners for each EMEA region – Eastern Europe & CIS, Middle East & Africa, South Europe, North Europe, UK/Ireland & Israel - as per the criteria outlined above (2) Oracle on Oracle, in this instance, means ZS3 or ZBA storage attached to DB or DB options, Engineered Systems or Sparc servers sold to the same customer by the same partner within the contest timelines.(3) Two VAD winners, one for each of the criteria outlined above, will be selected from across EMEA. Normal 0 14 false false false IT X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0cm; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi; mso-fareast-language:EN-US;}

Read the article

Successfully Deliver on State and Local Capital Projects through Project Portfolio Management

- by Sylvie MacKenzie, PMP

Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} While the debate continues on Capitol Hill about which federal programs to cut and which to keep, communities and towns across America are feeling the budget crunch closer to home. State and local governments are trying to save as many projects as they can without promising too much to constituents – and they, in turn, want to know where their tax dollars are going. Fortunately, with the right planning and management, you can deliver successful projects and portfolios on a limited budget. Watch the replay of our recent webcast with Oracle Primavera and Industry Product Manager Garrett Harley that will demonstrate how state and local governments can get the most out of their capital projects and learn how two Oracle Primavera customers have implemented project portfolio management practices to: Predict the cost of long-term capital programs and projects Assess risk and mitigation strategies Collaborate and track performance across government agencies Speakers: Garrett Harley, Industry and Product Manager, Oracle Primavera Cory Davis, Director of Capital Renovation and New Construction, Chicago Public Schools Julie Owen, PSP™, CCC™, Sr. Project Controls Manager,LA Metro Transit Authority With the right planning and management, state and local governments can deliver successful projects on a limited budget. 1024x768 Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif"; mso-fareast-font-family:"Times New Roman";}

Read the article

Faster Trip to Innovation with Simplified Data Integration: Sabre Holdings Case Study

- by Tanu Sood

Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin-top:0in; mso-para-margin-right:0in; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0in; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} Author: Irem Radzik, Director of Product Marketing, Data Integration, Oracle In today’s fast-paced, competitive environment, IT teams are under pressure to deliver technology solutions for many critical business initiatives as fast as possible. When the focus is on speed, it can be easy to continue to use old style, point-to-point custom scripts that grow organically to the point where they are unmanageable and too costly to maintain. As data volumes, data sources, and end users grow, uncoordinated data integration efforts create significant inefficiencies for both IT and business users. In addition to losing IT productivity due to maintaining spaghetti architecture, data integrity becomes a concern as well. Errors caused by inconsistent, data and manual data entry can prove very costly for companies and disrupt business activities. Many industry leaders recognize now that data should be moved in an automated and reliable manner across all platforms to have one version of the truth. By simplifying their data integration architecture and standardizing on a centralized approach, IT teams now accelerate time to market. Especially, using a centralized, shared-service approach brings agility, increases IT productivity, and frees up resources for innovation. One such industry leader that simplified its data integration architecture is Sabre Holdings. Sabre Holdings provides distribution and technology solutions for the travel industry, and is a winner of Oracle Excellence Awards for Fusion Middleware in 2011 in the data integration category. I had the pleasure to host Sabre Holdings on a public webcast and discuss their data integration best practices for data warehousing. In this webcast Sabre’s Amjad Saeed, presented how the company reduced complexity by consolidating systems and standardizing development on Oracle Data Integrator and Oracle GoldenGate for its global data warehouse development team. With Oracle’s complete real-time data integration solution, Sabre also streamlined support and maintenance operations, achieved real-time view in the execution of the integration processes, and can manage the data warehouse and business intelligence solution performance on demand. By reducing complexity and leveraging timely market insights, the company was able to decrease time to market by 40%. You can now listen to the webcast on demand: Sabre Holdings Case Study: Accelerating Innovation using Oracle Data Integration I invite you to hear directly from Sabre how to use advanced data integration capabilities to enable accelerated innovation. To learn more about Oracle’s data integration offering you can download our free resources.

Read the article

New PeopleSoft HCM 9.1 On Demand Standard Edition provides a complete set of IT services at a low, predictable monthly cost

- by Robbin Velayedam

At Oracle Open World last month, Oracle announced that we are extending our On Demand offerings with the general availability of PeopleSoft On Demand Standard Edition. Standard Edition represents Oracle’s commitment to providing customers a choice of solutions, technology, and deployment options commensurate with their business needs and future growth. The Standard Edition offering complements the traditional On Demand offerings (Enterprise and Professional Editions) by focusing on a low, predictable monthly cost model that scales with the size of your business. As part of Oracle's open cloud strategy, customers can freely move PeopleSoft licensed applications between on premise and the various on demand options as business needs arise. In today’s business climate, aggressive and creative business objectives demand more of IT organizations. They are expected to provide technology-based solutions to streamline business processes, enable online collaboration and multi-tasking, facilitate data mining and storage, and enhance worker productivity. As IT budgets remain tight in a recovering economy, the challenge becomes how to meet these demands with limited time and resources. One way is to eliminate the variable costs of projects so that your team can focus on the high priority functions and better predict funding and resource needs two to three years out. Variable costs and changing priorities can derail the best laid project and capacity plans. The prime culprits of variable costs in any IT organization include disaster recovery, security breaches, technical support, and changes in business growth and priorities. Customers have an immediate need for solutions that are cheaper, predictable in cost, and flexible enough for long-term growth or capacity changes. The Standard Edition deployment option fulfills that need by allowing customers to take full advantage of the rich business functionality that is inherent to PeopleSoft HCM, while delegating all application management responsibility – such as future upgrades and product updates – to Oracle technology experts, at an affordable and expected price. Standard Edition provides the advantages of the secure Oracle On Demand hosted environment, the complete set of PeopleSoft HCM configurable business processes, and timely management of regular updates and enhancements to the application functionality and underlying technology. Standard Edition has a convenient monthly fee that is scalable by number of employees, which helps align the customer’s overall cost of ownership with its size and anticipated growth and business needs. In addition to providing PeopleSoft HCM applications' world class business functionality and Oracle On Demand's embassy-grade security, Oracle’s hosted solution distinguishes itself from competitors by offering customers the ability to transition between different deployment and service models at any point in the application ownership lifecycle. As our customers’ business and economic climates change, they are free to transition their applications back to on-premise at any time. HCM On Demand Standard Edition is based on configurability options rather than customizations, requiring no additional code to develop or maintain. This keeps the cost of ownership low and time to production less than a month on average. Oracle On Demand offers the highest standard of security and performance by leveraging a state-of-the-art data center with dedicated databases, servers, and secured URL all within a private cloud. Customers will not share databases, environments, platforms, or access portals with other customers because we value how mission critical your data are to your business. Oracle’s On Demand also provides a full breadth of disaster recovery services to provide customers the peace of mind that their data are secure and that backup operations are in place to keep their businesses up and running in the case of an emergency. Currently we have over 50 PeopleSoft customers delegating us with the management of their applications through Oracle On Demand. If you are a customer interested in learning more about the PeopleSoft HCM 9.1 Standard Edition and how it can help your organization minimize your variable IT costs and free up your resources to work on other business initiatives, contact Oracle or your Account Services Representative today.

Read the article

How can I best implement 'cache until further notice' with memcache in multiple tiers?

- by ajreal

the term "client" used here is not referring to client's browser, but client server Before cache workflow 1. client make a HTTP request --> 2. server process --> 3. store parsed results into memcache for next use (cache indefinitely) --> 4. return results to client --> 5. client get the result, store into client's local memcache with TTL After cache workflow 1. another client make a HTTP request --> 2. memcache found return memcache results to client --> 3. client get the result, store into client's local memcache with TTL TTL = time to live Is possible for me to know when the data was updated, and to expire relevant memcache(s) accordingly. However, the pitfalls on client site cache TTL Any data update before the TTL is not pick-up by client memcache. In reverse manner, where there is no update, client memcache still expire after the TTL First request (or concurrent requests) after cache TTL will get throttle as it need to repeat the "Before cache workflow" In the event where client require several HTTP requests on a single web page, it could be very bad in performance. Ideal solution should be client to cache indefinitely until further notice. Here are the three proposals about futher notice Proposal 1 : Make use on HTTP header (current implementation) 1. client sent HTTP request last modified time header 2. server check if last data modified time=last cache time return status 304 3. client based on header to decide further processing GOOD? ---- - save some parsing for client - lesser data transfer BAD? ---- - fire a HTTP request is still slow - server end still need to process lots of requests Proposal 2 : Consistently issue a HTTP request to check all data group last modified time 1. client fire a HTTP request 2. server to return last modified time for all data group 3. client compare local last cache time with the result 4. if data group last cache time < server last modified time then request again for that data group only GOOD? ---- - only fetch what is no up-to-date - less requests for server BAD? ---- - every web page require a HTTP request Proposal 3 : Tell client when new data is available (Push) 1. when server end notice there is a change on a data group 2. notify clients on the changes 3. help clients to fetch again data 4. then reset client local memcache after data is parsed GOOD? ---- - let the cache act/behave like a true cache BAD? ---- - encourage race condition My preference is on proposal 3, and something like Gearman could be ideal Where there is a change, Gearman server to sent the task to multiple clients (workers). Am I crazy? (I know my first question is a bit crazy)

Read the article

What Counts For a DBA – Depth

- by Louis Davidson

SQL Server offers very simple interfaces to many of its features. Most people could open up SSMS, connect to a server, write a simple query and see the results. Even several of the core DBA tasks are deceptively straightforward. It doesn’t take a rocket scientist to perform a basic database backup or run a trace (even using the newfangled Extended Events!). However, appearances can be deceptive, and often times it is really important that a DBA understands not just the basics of how to perform a task, but why we do a task, and how that task works. As an analogy, consider a child walking into a darkened room. Most would know that they need to turn on the light, and how to do it, so they flick the switch. But what happens if light fails to shine forth. Most would immediately tell you that you need to consider changing the light bulb. So you hop in the car and take them to the local home store and instruct them to buy a replacement. Confronted with a 40 foot display of light bulbs, how will they decide which of the hundreds of types of bulbs, of different types, fittings, shapes, colors, power and efficiency ratings, is the right choice? Obviously the main lesson the child is going to learn this day is how to use their cell phone as a flashlight so they don’t have to ask for help the next time. Likewise, when the metaphorical toddlers who use your database server have issues, they will instinctively know something is wrong, and may even have some idea what caused it, but will have no depth of knowledge to figure out the right solution. That is where the DBA comes in and attempts to save the day. However, when one looks beneath the shiny UI, SQL Server has its own “40 foot display of light bulbs”, in the form of the tremendous number of tools and the often-bewildering amount of information they can present to the DBA, to help us find issues. Unfortunately, resorting to guesswork, to trying different “bulbs” over and over, hoping to stumble on the answer. This is where the right depth of knowledge goes a long way. If we need to write a SELECT statement, then knowing the syntax and where to find the data is not enough. Knowledge of indexes and query plans is essential. Without it, we might hit on a query that “works”, but we are basically still a user, not a programmer, because we have no real control over our platform. Is that level of knowledge deep enough? Probably not, since knowledge of the underlying metadata and structures would be very useful in helping us make sense of any query plan. Understanding the structure of an index makes the “key lookup” operator not sound like what you do when someone tapes your car key to the ceiling. So is even this level of understanding deep enough? Do we need to understand the memory architecture used to process the query? It might be a comforting level of knowledge, and will doubtless come in handy at some point, but is not strictly necessary in most cases. Beyond that lies (more or less) full knowledge of SQL language and the intricacies of every step the SQL Server engine takes to process our query. My personal theory is that, as a professional, our knowledge of a given task should extend, at a minimum, one level deeper than is strictly necessary to perform the task. Anything deeper can be left to the ridiculously smart, or obsessive, or both. As an example. tasked with storing an integer value between 0 and 99999999, it’s essential that I know that choosing an Integer over Decimal(8,0) will likely offer performance benefits. It is then useful that I also understand the value of adding a CHECK constraint, to make sure the values are valid to the desired range; and comforting that I know a little about the underlying processors, registers and computer math. Anything further, I leave to the likes of Joe Chang, whose recent blog post on the topic offers depth by the bucketful!

Read the article

Test Drive for Partners on Oracle Endeca Information Discovery

- by Mike.Hallett(at)Oracle-BI&EPM

Normal 0 false false false EN-GB X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0cm; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi; mso-fareast-language:EN-US;} Specifically for Oracle Partners, this half-day hands-on workshop allows you to experience Information Discovery from Oracle in order to: Understand Information Discovery and how it compliments classic BI solutions Use Search and Guided Navigation to see how structured and unstructured information can be rapidly brought together to unlock hidden value Explore all of your data in any format and from any source including social media, market surveys and reports Lay the foundation for helping business users who need fast answers to new questions Experience the amazing performance of Endeca on Oracle's in memory Exalytics machine Agenda After an introduction to Oracle Endeca Information Discovery, follow a self-paced, supervised, hands-on tutorial where you will see how easy it is to: Use Guided Navigation and Search to explore structured and unstructured data Rapidly integrate new and changing data sources such as Social Media Build new Discovery user interfaces Rapidly respond to changing business needs and data environments And ask questions of Oracle's Business Analytics experts throughout When 14th March 2013, Registration 9:00 a.m. - finish by 1:00 p.m. Normal 0 false false false EN-GB X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0cm; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi; mso-fareast-language:EN-US;} Register Now What: Oracle Endeca Information Discovery Test Drive Where: Oracle City Office, 1 South Place, London, EC2M 2RB

Read the article

CFOs: Do You Have a Playbook for Growth?

- by Oracle Accelerate for Midsize Companies

by Jim Lein, Oracle Midsize Programs In most global markets, CFOs are optimistic about their company's growth opportunities. Deloitte's CFO Signals Report, "Time to Accelerate" found that: In the U.K. business optimism is at its highest level in three-and-a-half years Optimism in North America rose from a strong +42% last quarter (Q2 to Q3 2013) to an even stronger +54%. The inaugural Southeast Asia survey, 44% of CFOs reported a positive outlook despite worries over the Chinese economy and political uncertainty. Sustainable and profitable business growth doesn't usually happen by accident. Company's need a playbook for growth that's owned by the CFO. And today, that playbook must leverage the six enabling technologies--Social, Big Data, Mobile, Cloud, Analytics, and The Internet of Things (or, as Oracle president Mark Hurd explains, "The Internet of the People"). On Monday June 9 at 2:00 pm Eastern, CFO.com is hosting a webcast, "The CFO Playbook on Growth: How CFOs Can Boost Efficiency and Performance with Automation". Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} “Investing in technology begins with a business metric driven business case with clear tangible business results expected," says John Lieblang, Affiliate Partner with Waterstone Management Group. "The progressive CFO has learned how to forge a partnership with the CIO to align everyone in the 'result value chain' to be accountable for the business results not just for functional technology.” Click HERE to register Looking for more news and information about Oracle Solutions for Midsize Companies? Read the latest Oracle for Midsize Companies Newsletter Sign-up to receive the latest communications from Oracle’s industry leaders and experts Jim Lein I evangelize Oracle's enterprise solutions for growing midsize companies. I recently celebrated 15 years with Oracle, having joined JD Edwards in 1999. I'm based in Evergreen, Colorado and love relating stories about creativity and innovation whether they be about software, live music, or the mountains. The views expressed here are my own, and not necessarily those of Oracle.

Read the article

Cloud – the forecast is improving

- by Rob Farley

There is a lot of discussion about “the cloud”, and how that affects people’s data stories. Today the discussion enters the realm of T-SQL Tuesday, hosted this month by Jorge Segarra. Over the years, companies have invested a lot in making sure that their data is good, and I mean every aspect of it – the quality of it, the security of it, the performance of it, and more. Experts such as those of us at LobsterPot Solutions have helped these companies with this, and continue to work with clients to make sure that data is a strong part of their business, not an oversight. Whether business intelligence systems are being utilised or not, every business needs to be able to rely on its data, and have the confidence in it. Data should be a foundation upon which a business is built. In the past, data had been stored in paper-based systems. Filing cabinets stored vital information. Today, people have server rooms with storage of various kinds, recognising that filing cabinets don’t necessarily scale particularly well. It’s easy to ‘lose’ data in a filing cabinet, when you have people who need to make sure that the sheets of paper are in the right spot, and that you know how things are stored. Databases help solve that problem, but still the idea of a large filing cabinet continues, it just doesn’t involve paper. If something happens to the physical ‘filing cabinet’, then the problems are larger still. Then the data itself is under threat. Many clients have generators in case the power goes out, redundant cables in case the connectivity dies, and spare servers in other buildings just in case they’re required. But still they’re maintaining filing cabinets. You see, people like filing cabinets. There’s something to be said for having your data ‘close’. Even if the data is not in readable form, living as bits on a disk somewhere, the idea that its home is ‘in the building’ is comforting to many people. They simply don’t want to move their data anywhere else. The cloud offers an alternative to this, and the human element is an obstacle. By leveraging the cloud, companies can have someone else look after their filing cabinet. A lot of people really don’t like the idea of this, partly because the administrators of the data, those people who could potentially log in with escalated rights and see more than they should be allowed to, who need to be trusted to respond if there’s a problem, are now a faceless entity in the cloud. But this doesn’t mean that the cloud is bad – this is simply a concern that some people may have. In new functionality that’s on its way, we see other hybrid mechanisms that mean that people can leverage parts of the cloud with less fear. Companies can use cloud storage to hold their backup data, for example, backups that have been encrypted and are therefore not able to be read by anyone (including administrators) who don’t have the right password. Companies can have a database instance that runs locally, but which has its data files in the cloud, complete with Transparent Data Encryption if needed. There can be a higher level of control, making the change easier to accept. Hybrid options allow people who have had fears (potentially very justifiable) to take a new look at the cloud, and to start embracing some of the benefits of the cloud (such as letting someone else take care of storage, high availability, and more) without losing the feeling of the data being close. @rob_farley

Read the article

What Counts for a DBA: Skill

- by drsql

“Practice makes perfect:” right? Well, not exactly. The reality of it all is that this saying is an untrustworthy aphorism. I discovered this in my “younger” days when I was a passionate tennis player, practicing and playing 20+ hours a week. No matter what my passion level was, without some serious coaching (and perhaps a change in dietary habits), my skill level was never going to rise to a level where I could make any money at the sport that involved something other than selling tennis balls at a sporting goods store. My game may have improved with all that practice but I had too many bad practices to overcome. Practice by itself merely reinforces what we know and what we can figure out naturally. The truth is actually closer to the expression used by Vince Lombardi: “Perfect practice makes perfect.” So how do you get to become skilled as a DBA if practice alone isn’t sufficient? Hit the Internet and start searching for SQL training and you can find 100 different sites. There are also hundreds of blogs, magazines, books, conferences both onsite and virtual. But then how do you know who is good? Unfortunately often the worst guide can be to find out the experience level of the writer. Some of the best DBAs are frighteningly young, and some got their start back when databases were stored on stacks of paper with little holes in it. As a programmer, is it really so hard to understand normalization? Set based theory? Query optimization? Indexing and performance tuning? The biggest barrier often is previous knowledge, particularly programming skills cultivated before you get started with SQL. In the world of technology, it is pretty rare that a fresh programmer will gravitate to database programming. Database programming is very unsexy work, because without a UI all you have are a bunch of text strings that you could never impress anyone with. Newbies spend most of their time building UIs or apps with procedural code in C# or VB scoring obvious interesting wins. Making matters worse is that SQL programming requires mastery of a much different toolset than most any mainstream programming skill. Instead of controlling everything yourself, most of the really difficult work is done by the internals of the engine (written by other non-relational programmers…we just can’t get away from them.) So is there a golden road to achieving a high skill level? Sadly, with tennis, I am pretty sure I’ll never discover it. However, with programming it seems to boil down to practice in applying the appropriate techniques for whatever type of programming you are doing. Can a C# programmer build a great database? As long as they don’t treat SQL like C#, absolutely. Same goes for a DBA writing C# code. None of this stuff is rocket science, as long as you learn to understand that different types of programming require different skill sets and you as a programmer must recognize the difference between one of the procedural languages and SQL and treat them differently. Skill comes from practicing doing things the right way and making “right” a habit.

Read the article

Does every project benefit from written specifications?

- by nikie

I know this is holy war territory, so please read the question to the end before answering. There are many cases where written specifications make a lot of sense. For example, if you're a contractor and you want to get paid, you need written specs. If you're working in a team with 20 persons, you need written specs. If you're writing a programming language compiler or interpreter (and it's not perl), you'll usually write a formal specification. I don't doubt that there are many more cases where written specifications are a really good idea. I just think that there are cases where there's so little benefit in written specs, that it doesn't outweigh the costs of writing and maintaining them. EDIT: The close votes say that "it is difficult to say what is asked here", so let me clarify: The usefulness of written, detailed specifications is often claimed like a dogma. (If you want examples, look at the comments.) But I don't see the use of them for the kind of development I'm doing. So what is asked here is: How would written specifications help me? Background information: I work for a small company that's developing vertical market software. If our product is easier to use and has better performance than the competition, it sells. If it's harder to use, even if it behaves 100% as the specification says, it doesn't sell. So there are no "external forces" for having written specs. The advantage would have to be somewhere in the development process. Now, I can see how frozen specifications would make a developer's life easier. But we'll never have frozen specs. If we see in the middle of development that feature X is not intuitive to use the way it's specified, then we can only choose between changing the specification or developing a product that won't sell. You'll probably ask by now: How do you know when you're done? Well, we're continually improving our product. The competition does the same. So (hopefully) we're never done. We keep improving the software, and when we reach a point when the benefits of the improvements we've added since the last release outweigh the costs of an update, we create a new release that is then tested, localized, documented and deployed. This also means that there's rarely any schedule pressure. Nobody has to do overtime to make a deadline. If the feature isn't done by the time we want to release the next version, it'll simply go into the next version. The next question might be: How do your developers know what they're supposed to implement? The answer is: They have a lot of domain knowledge. They know the customers business well enough, so a high-level description of the feature (or even just the problem that the customer needs solved) is enough to implement it. If it's not clear, the developer creates a few fake screens to get feedback from marketing/management or customers, but this is nowhere near the level of detail of actual specifications. This might be inefficient for larger teams, but for a small team with low turnover it works quite well. It has the additional benefit that the developer in question often comes up with a better solution than the person writing the specs might have. This question is already getting very long, but let me address one last point: Testing. Like I said in the beginning, if our software behaves 100% like the spec says, it still can be crap. In fact, if it's so unintuitive that you need a spec to know how to test it, it probably is crap. It makes sense to have fixed, written tests for some core functionality and for regression bugs, but again, this is nowhere near a full written spec of how the software should behave when. The main test is: hand the software to a user who doesn't know it yet and tell him to use the new feature X. If she can figure out how to use it and it works, it works.

Search Results

Search found 13151 results on 527 pages for 'performance counters'.

Page 486/527 | < Previous Page | 482 483 484 485 486 487 488 489 490 491 492 493 | Next Page >

- by marc dekeyser

- by JavaCecilia

- by Mark Rackley

- by ryanzec

- by speakjava

- by asd

- by jlaskey

- by Brad Patton

- by dgel

- by MarkPearl

- by Mike.Hallett(at)Oracle-BI&EPM

- by johnny-b

- by Postman

- by Matt Sieker

- by Claudia Caramelli-Oracle

- by Sylvie MacKenzie, PMP

- by Tanu Sood

- by Robbin Velayedam

- by ajreal

- by Louis Davidson

- by Mike.Hallett(at)Oracle-BI&EPM

- by Oracle Accelerate for Midsize Companies

- by Rob Farley

- by drsql

- by nikie

< Previous Page | 482 483 484 485 486 487 488 489 490 491 492 493 | Next Page >