Search Results

Search found 7154 results on 287 pages for 'networking'.

Page 50/287 | < Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >

  • Disabling IPv6 on a single interface

    - by ijw
    I'm slightly weirded out by the fact that Ubuntu won't process ipv4 DHCP unless you explicitly tell it to, but will happily take ipv6 RAs unless you tell it not to. Is there any way to change the default behaviour to be 'do nothing unless I explicitly turn it on'? (Note to answerers: I'm not looking to globally disable ipv6, or completely turn off autoconf. I'm looking to disable autoconf by default (as in, I don't want ipv6 unless I say so in /etc/network/interfaces, in the same way that I don't just get a v4 address unless I've explicitly turned on dhcp). What's happening is that, for any interface that's up - e.g. has an ipv4 config - a v6 address tends to just turn up on the interface as well, despite the fact that I've not enabled that explicitly. The solutions to date are fine as far as they go, but if I disable v6 or autoconf globally, I can't then re-enable v6 on a per-interface basis with a simple command in /etc/network/interfaces. I'm fairly sure I'm asking for the moon on a stick, mind you.)

    Read the article

  • How can an application (like Firefox) be forced to use a certain network interface?

    - by Lekensteyn
    I've two interfaces: eth0 and wlan0 on a notebook. Possible use cases: eth0 grants me Internet access, and wlan0 is currently connected to a router which does not have Internet-connectivity. For development purposes, I need to connect to the wlan0 by default, but use eth0 for surfing eth0 and wlan0 are both connected to the Internet. For a torrent application, eth0 should be used for speed, but for portability of the notebook, SSH should have a connection over wlan0 eth0 is a wire connection, wlan0 is a wireless one. Sensible data should be transferred over eth0, but other traffic can go over wlan0 as well. Is there a way to force applications (like nc.traditional or firefox) to use a certain network interface? A wrapper like example-wrapper eth0 program is fine too if such program exist. It would be nice if it could configured within Firefox (in runtime). I'd like to avoid IPTables solutions if possible.

    Read the article

  • About cdn architecture to route way

    - by Tony Lee
    Our web system, use the third-party cdn service. Assume that the user set the local dns with the googledns or opendns to visit our web sites, so cdn service will select the closest cdn proxy node. all right, but in fact the user's actual access position might outside there, cdn service may chose the one furthest away from the user node, so static resource access slower.. At present, my idea is if user local set dns server with googledns, and then first one we get the actual ip address of the user, tracerote to test a best routing lines, set up a cookie in user browser, and then set 302 header for response to jump to the which best cdn node. Whether the user's browser side traceroute tool can provide the best route decision-making ? Because we find that, once the user to set local dns server with the foreign network segment, for example : set dns with 8.8.8.8, so cdn routing will choose the foreign service node.

    Read the article

  • Ubuntu 12.04 USB wireless not recognized

    - by Justin
    I have searched for awhile now for ways to fix my problem but have come up with nothing. I am running Ubuntu 12.04 on my desktop computer. I am unable to find the Enable Wireless button in the network area. It just doesn't appear. Everything else works on my laptop. I believe it's the drivers for my USB network adapter. I also have no way of using a wired connection at the moment. Thanks for any help!

    Read the article

  • A simple example of movement prediction

    - by Daniel
    I've seen lots of examples of theory about the reason for client-side prediction, but I'm having a hard time converting it into code. I was wondering if someone knows of some specific examples that share some of the code, or can share their knowledge to shed some light into my situation. I'm trying to run some tests to get a the movement going (smoothly) between multiple clients. I'm using mouse input to initiate movement. I'm using AS3 and C# on a local Player.IO server. Right now I'm trying to get the Client side working, as I'm only forwarding position info with the client. I have 2 timers, one is an onEnterFrame and the other is a 100ms Timer, and one on mouseClick listener. When I click anywhere with a mouse, I update my player class to give it a destination point On every enterFrame Event for the player, it moves towards the destination point At every 100ms it sends a message to the server with the position of where it should be in a 100ms. The distance traveled is calculated by taking the distance (in Pixels) that the player can travel in one second, and dividing it by the framerate for the onEnterFrame handler, and by the update frequency (1/0.100s) for the server update. For the other Players, the location is interpolated and animated on every frame based on the new location. Is this the right way of doing it?

    Read the article

  • How to setup a wifi ap hotspot with ipv6 support?

    - by keyman
    How to setup a wifi ap (access point mode) hotspot, with IPv6 support? I've set up a hotspot according to the guide to wifi ap hotspot setup and it works fine. But via the hotspot I failed to visit IPv6 websites. How can I setup a hotspot able to share Ipv6 Internet access? Thanks! Further: Actually I've tried to setup IPv6 forwarding and masquerading. First enabling IPv6 forwarding: echo 1 | sudo tee net/ipv6/conf/default/forwarding Then I tried to execute: sudo ip6tables -t nat -A POSTROUTING -s 2001:db8:0:1::/64 -o eth0 -j MASQUERADE But it gave me an error: ip6tables v1.4.12: Couldn't load target `MASQUERADE':No such file or directory I searched through the Internet but I get confused. So I'm here for help. Thanks!

    Read the article

  • upgrade from 11.10 to 12.04 killed my network connectivity

    - by Daniel
    I have a wired network connection that worked fine in version 11.10. I upgraded to 12.04 and immediately after the upgrade was completed, the OS reported my "cable unplugged". It is not unplugged and it is not defective. I have a D-link DFE-530TXS 10/100 ethernet NIC and I see what seems to be the generic 10050 driver loaded. Is there any way to just flush anything and everything to do with the network configuration and have Ubuntu reset/find everything again? If not...is there any way I can get it to realize that my network cable is not unplugged? (considering it worked mere minutes before). Thanks.

    Read the article

  • SS7(M3UA, SCCP, TCAP, MAP) Stack

    - by Ammar Hameed
    I'm building an open source SMSC from scratch; it's almost finished, The SRI and the forwardSM operations are working, but I still have few things to do for the receiving part. I've built the SS7 stack already, but I'm using DB for saving the TCAP transactions IDs to be updated later to get/generate responses. My approach is this: I created memory table (heap table), saved the TCAP TID in the database, then compared the received TCAP TID with the TIDs saved in the database and then decide whether to end the TCAP session or continue. What is the best way to implement it? I'm thinking of doubly linked list that holds the TCAP TID. Am I going towards the right direction, or should I use another technique other than database or D-linked list? Should I leave it as it is, and let the database do the job for saving the TIDs? Please note that I'm using SCTP implementation available on Linux (lsctp) as a transport protocol, the language I'm using is C and the DB is MYSQL.

    Read the article

  • How to establish VPN Connection using Vodafone K3773 HSPA USB Stick?

    - by user1889139
    I am using Ubuntu 12.04 Desktop. I am trying to establish VPN PPTP connection to Ubuntu 12.04 Server. VPN connection available when PC is connected to LAN - ADSL modem - Internet - VPN Server. No VPN connection available when using 3G modem Vodafone K3773 HSPA USB Stick - Internet - VPN Server. Internet is connected. VPN is not. How to establish the VPN Connection? Server side log: GRE: Bad checksum from pppd.

    Read the article

  • Static IP breaks Network connection

    - by Pasquale Tedesco
    I am somewhat new to Linux. I am setting up a Web server and installed Ubuntu server 14.04 on an vSphere ESXi 5.5 host. I am connecting perfectly fine to the internet when using DHCP but when I apply my Static settings I loose the ability to connect to websites. Whats weird is I can Ping google.com but if I try wget gooogl.com it hangs at connecting to google.com (google.com):173.194.43.32:80 and I get "failed: connection refused" But if I am set to DHCP the connection resolves perfectly. Thanks # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 #iface eth0 inet dhcp iface eth0 inet static address 10.1.2.25 gateway 10.1.2.2 netmask 255.255.255.0 search tsig.com dns-nameservers 10.1.2.13 10.1.2.30

    Read the article

  • Start & Stop internet connexion without broking Network Manager

    - by user3634569
    I am on Precise. I used this command (with an alias), to close the network, dbus-send --system --print-reply --reply-timeout=120000 --type=method_call --dest=org.freedesktop.NetworkManager /org/freedesktop/NetworkManager org.freedesktop.NetworkManager stop it worked, now I have to use dbus-send --system --print-reply --reply-timeout=120000 --type=method_call --dest=org.freedesktop.NetworkManager /org/freedesktop/NetworkManager org.freedesktop.NetworkManager.Sleep boolean:true it work but not so well, sometimes I can't restart the network and NetworkManager is blocked too and strange errors even GUI freeze . What I need is a command line which close the network and don't mess with Network Manager, maybe with the routing table or what else.

    Read the article

  • Scuttlebutt Reconciliation from "Efficient Reconciliation and Flow Control for Anti-Entropy Protocols"

    - by Maus
    This question might be more suited to math.stackexchange.com, but here goes: Their Version Reconciliation takes two parts-- first the exchange of digests, and then an exchange of updates. I'll first paraphrase the paper's description of each step. To exchange digests, two peers send one another a set of pairs-- (peer, max_version) for each peer in the network, and then each one responds with a set of deltas. The deltas look like: (peer, key, value, version), for all tuples for which peer's state maps the key to the given value and version, and the version number is greater than the maximum version number peer has seen. This seems to require that each node remember the state of each other node, and the highest version number and ID each node has seen. Question Why must we iterate through all peers to exchange information between p and q?

    Read the article

  • Ubuntu Server 12.04 as a router. Problem with DNS?? Or Routing table?

    - by Lorenzo
    I have a virtualbox lab made up of 4 Windows 2008 R2 servers (DC/DNS,SQL,SHAREPOINT, EXCHANGE) that are configured with static ip addresses with NIC's attached to Internal network. Everything works. I had the requirement to execute some tests that also access external services available on the internet. To keep things clean and similar to the production environment I have installed another VM, with Ubuntu Server 12.04 64 bit and configured (I hope) to work as a router like described on this post. This VM has two network interfaces: first is Bridged with the host and is used as a WAN connection and the other one attached in the Internal Network with its own static IP address on the internal network subnet. But actually the Windows servers does not connect to the internet while the unix one connects. I did a route command. this is the result: Kernel IP Routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.69.121.1 0.0.0.0 UG 100 0 0 eth0 10.69.121.0 * 255.255.255.0 U 0 0 0 eth0 192.168.83.0 * 255.255.255.0 U 0 0 0 eth1 Can somebody help me with this configuration? :) Thanks! Addendum: I forgot to mention that one of the windows server hosts a DNS service for which I should maybe configure a forwarding server but I do not exactly know which server to forward on... :(

    Read the article

  • svn-based versioning tool, problem with network timeout

    - by Scarlet
    My dev team was committed a versioning tool based on Subversion to run on Windows (our svn client is sliksvn). We're developing with Delphi XE2, should that matter. We're asked to implement a "check for updates availability" feature, which has to work as follows: Connect to the SVN repo via svn+ssh protocol; See if there are changes to receive and list them; Let the user decide if he wants to receive changes or not. We don't have a great knowledge on svn, so we thought to implement that thing client side by a certain number of CreateProcess calls that wrap directly proper svn commands. Anyways what we perceived is that if network problems should arise, such like a connection drop, svn client hangs forever waiting for the operation to close instead of failing for timeout. We know that CreateProcess can be given a timeout argument, but it wouldn't be correct to use it, as we can't know from outside how long will be the svn operation taking to complete. Is there any way to avoid that deadlock?

    Read the article

  • Network configuration problem with ubuntu

    - by Musti
    I am a new Ubuntu user. In my dorm there is a bit strange connection way for internet, I have to configure given "IP address, Subnetmask, Default gateway, Preferred DNS server, and Alternate DNS server" to have an internet connection, otherwise it is imposible. Actually it is very easy in windows, I am just opening Network and Sharing Center and then setting up TCP/IPv4. I had some attempt in Ubuntu, but just failed :/ Can anyone tell me how to configure? Thanks in advance... Musti

    Read the article

  • Printing Problem on Shared Printer

    - by paulus_almighty
    I'm using Ubuntu 11.10 on two machines. One has a USB printer connected. I want to share this printer with the other over the wireless network. Under Printing > Server > Settings: I have Publish shared printers connected to this system and Allow printing from the internet enabled. All other checkboxes are disabled. When I right click on the printer icon, I can see enabled and shared are ticked. On my other machine, I can now click on add network printer. It finds the machine name of the server and correctly identifies the printer. However, print test page fails. Under printer properties the printer state says: Processing - Unable to connect to printer; will retry in 30 seconds... What's gone wrong?

    Read the article

  • Ethernet Wired Connection Help

    - by user107598
    I have recently installed Ubuntu 12.10 onto my Dell Inspiron N5010 and Ive been all over many forums trying to figure out how I can get my ethernet cable to be recognized so I can set up a wired connection. My Network Card is the Realtek RT8139 and from what Ive gathered the ethernet port driver for it is installed. Whenever I run ifconfig in the terminal it says that eth1 is up and running but no matter how I edit the connection I cannot get it to work. If anyone can help it would be greatly appreciated!

    Read the article

  • Problems with NAT Adapater since upgrade to Ubuntu 12.10

    - by jjesse
    I was running Ubuntu 12.04 w/ VirtualBox installed. I was using the NAT interface to connect to everything. Basically running VBOX for testing some things and a Windows VM for Netflix.. Was back to working in my VMs today and noticed that I was unable to connect to the internet. In the VM settings I'm using the NAT adapter, however I noticed there is no NAT adapter in the Network Settings under Preferences in VBOX. Not quite sure what happened but wonder what is going on? I noticed there are some posts about changes DNSMASQ and configuring a bridge mode, but this worked out of the box under 12.04 and since the upgrade this no longers work. Need some help please

    Read the article

  • Is it illegal to forward copyrighted content? [closed]

    - by Mike
    Ok, this may be a strange question, but let's start: If I illegally download a movie (for example...) from a HTTP Web Server, there are many routers between me and the Web Server which are forwarding the data to my PC. As I understand, the owners of the routers are not legally responsible for the data they forward (please correct if I'm wrong). What if I would install a client of a peer-to-peer network on my PC and this client (peer) would forward copyrighted content received from peers to other peers? Hope someone understand what I mean ;-) Any answer or comment would be highly appreciated. Mike Update 1: I'm asking this question because I want to develop a p2p-application and try to figure out how to prevent illegal content sharing/distribution (if forwarding content is really illegal...) Update 2: What if the data forwarded by my peer is encrypted, so I'm technically not able to read and check it?

    Read the article

  • Proxy authentication box not showing (sometimes)

    - by zerologiko
    I'm behind a proxy that require authentication by means of user/pass. I'm using Ubuntu 11.04, I think the proxy is "Squid". Usually everything works fine, that means that the browser shows me the window to insert proxy user/pass and I can navigate. The problem: Sometimes the browser refuse to show the authentication windows and if I wait enough it gives me an error like: Errore 130 (net::ERR_PROXY_CONNECTION_FAILED) Even if I restart, disconnect, the situation doesn't change. BUT on Windows the network (and the proxy) works.. So, bottomline what I know is: the network is working (though only on Windows) the Ubuntu configuration is ok (because i can navigate most days) The problems resolves itself in a few hours but I don't understand why. Some hints? Thanks in advance! Andrea

    Read the article

  • Question Virtual Network and NAT set-up

    - by Jay
    Hi Guys! I need some help. I'm completely new to Linux. I'm trying to set up the following scenario: +-----+eth0 +-----+ +---+ | VM2 |-----------| VM1 |---------------| H | +-----+ eth1 +-----+eth0 (NAT) +---+ VM2 - Virtual machine from Virtual Box, using Ubuntu VM1 - Virtual machine from Virtual Box, using Ubuntu: I want this to act as a NAT. H - Host, my Windows Vista The dots were just added since after saving the spaces disappear. So if I ping H from VM2, H would receive a different IP address from VM2. Could you give me a step by step on this? All machines are of course 32 bit. Thanks. Would appreciate the help so much.

    Read the article

  • Putting Ubuntu Server on to a networked HDD

    - by SimplySimon
    Firstly, I know very little about servers and secondly the 1Tb HDD I have has network capabilities, but no software is installed on it, so when connected to the computer it is seen as a network connection, but not as a drive. Any advice on how to get started would be great. Up until now, I have been using it as a USB drive which worked well, but when this is sorted, I would like it to be connected directly to our BT HomeHub accessible through the WiFi for all the family to use as a film and back up repository. I would then be able to set up individual accounts for each family member to use and may be, if possible, make it accessible from outside locations. The First question then is: How can I install Ubuntu server on the 1Tb HDD attached directly to the computers network port but which doesn't show up in Nautilus? HDD Western Digital 1.0Tb LBA 1953525168 Model: WD10EACS-00DB0 DCM: DHRNHT2CF

    Read the article

  • How Does Windows Confirm Wi-Fi Access and Whether Hot Spot Authentication Is Necessary?

    - by Jason Fitzpatrick
    Windows is quite adept at telling you if you have a properly functioning Internet connection, but how exactly does it do so? Digging into how Windows handles the problem offers insight into Windows connectivity messages. Today’s Question & Answer session comes to us courtesy of SuperUser—a subdivision of Stack Exchange, a community-drive grouping of Q&A web sites. How to Fix a Stuck Pixel on an LCD Monitor How to Factory Reset Your Android Phone or Tablet When It Won’t Boot Our Geek Trivia App for Windows 8 is Now Available Everywhere

    Read the article

  • Unable to remove network proxy

    - by Rushil
    I'm on 11.10 I'd set up a network proxy a couple of days back from system settings .And afterwards I'd set my proxy method back to none. However, my proxy has not been removed. I know this because: a: 127.0.0.1 routes me to the index.html file in the base directory of the proxy server. b: I'm able to access my university internet after hours. I checked my /etc/environment and etc/apt/apt.conf file and both of them have no proxy details. I also tried resetting the proxy and then getting rid of it but that didn't work either.

    Read the article

  • Bluetooth broadcasting realtime - is it possible

    - by user69961
    Is it possible to broadcast data via bluetooth to one ore more connected devices? I mean that each phone will be master and slave at the same time and each phone will broadcast data that should be received by all other phones. Or is the only possibility to use a "client-server"-like topology; one phone acts as a server and listens to all clients and then sends data from each client to the rest of clients in the network? Which variant should be more effective? If broadcasting is possible then the same implementation can be used for all devices and if one device will die communication between rest of network can continue. And also will there be enough to send one message per device - not message from each device to server and then back to all devices. Am I right?

    Read the article

< Previous Page | 46 47 48 49 50 51 52 53 54 55 56 57  | Next Page >