Search Results

Search found 18911 results on 757 pages for 'device manager'.

Page 531/757 | < Previous Page | 527 528 529 530 531 532 533 534 535 536 537 538  | Next Page >

• How to diagnose network speed drops

  - by Luis Alvarado

  Here is the image of System Monitor first: The graph shows the cycle the connection goes through. After 10 to 15 seconds it drops to 0 KB/S, then goes up to the Max speed (120 KB/S) then it repeats. dmesg shows the following during that time: [ 6066.757211] wlan0: send auth to 00:26:5a:b5:05:7b (try 1/3) [ 6066.804405] wlan0: authenticated [ 6066.804578] rt2800pci 0000:02:01.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 6066.805016] wlan0: associate with 00:26:5a:b5:05:7b (try 1/3) [ 6066.809218] wlan0: RX AssocResp from 00:26:5a:b5:05:7b (capab=0x431 status=0 aid=1) [ 6066.809581] wlan0: associated [ 6066.810203] bridge-eth0: disabling the bridge on dev down [ 6066.810239] bridge-eth0: down [ 6066.810254] bridge-eth0: detached [ 6066.810309] /dev/vmnet: open called by PID 1679 (vmnet-bridge) [ 6066.810322] /dev/vmnet: hub 0 does not exist, allocating memory. [ 6066.810355] /dev/vmnet: port on hub 0 successfully opened [ 6066.810366] bridge-wlan0: device is wireless, enabling SMAC [ 6066.810369] bridge-wlan0: up [ 6066.810372] bridge-wlan0: attached [ 6067.010285] userif-2: sent link down event. [ 6067.010290] userif-2: sent link up event. This also repeats with Wired or Wireless connections. How can I diagnose this changes in the network efficiently.

  Read the article

• BCM4306, b43 legacy driver installed, but "firmware missing" error

  - by ScrollerBlaster

  I have the following wireless hardware on a Compaq evo N600c laptop running lubuntu latest. ciaran@compaq:~$ lspci -vvnn | grep 14e4 03:00.0 Network controller [0280]: Broadcom Corporation BCM4306 802.11b/g Wireless LAN Controller [14e4:4320] (rev 03) Following the instructions from here : http://www.linuxwireless.org/en/users/Drivers/b43#b43_and_b43legacy I opted for the legacy firmware installer, following instructions for internet install to the letter (with no errors). i.e. I successfully installed sudo apt-get install firmware-b43legacy-installer In the nm-applet I now get Wireless networks device not ready (firmware missing) I open up Additional Drivers, but the list is empty. I have commented out this line in /etc/modprobe.d/blacklist.conf #blacklist bcm43xx Contents of firmware dir: ciaran@compaq:/etc/modprobe.d$ sudo ls /lib/firmware/b43legacy/ [sudo] password for ciaran: a0g0bsinitvals2.fw a0g0initvals5.fw b0g0bsinitvals2.fw b0g0initvals5.fw ucode11.fw ucode5.fw a0g0bsinitvals5.fw a0g1bsinitvals5.fw b0g0bsinitvals5.fw pcm4.fw ucode2.fw a0g0initvals2.fw a0g1initvals5.fw b0g0initvals2.fw pcm5.fw ucode4.fw Edit: from dmesg: [ 4460.193382] b43-phy0 ERROR: Firmware file "b43/ucode5.fw" not found [ 4460.193393] b43-phy0 ERROR: Firmware file "b43-open/ucode5.fw" not found [ 4460.193401] b43-phy0 ERROR: You must go to http://wireless.kernel.org/en/users/Drivers/b43#devicefirmware and download the correct firmware for this driver version. Please carefully read all instructions on this website. Yours in hope.

  Read the article

• Expiry time in notify-send notifications

  - by gsingh2011

  On my HP computer running Ubuntu 12.04, the brightness and volume increments were much higher than I wanted. On top of that, the notification for the volume was just plain wrong (0% sound did not correspond to 0 on the progress bar). So I decided to override these options with my own commands. I used CompizConfig Settings Manager to add custom commands to the brightness and volume keys (this couldn't be done in the regular settings because these keys were handled by the BIOS, unlike normal function keys). I used xbacklight to control the brightness and amixer to control the volume. The problem is that the nice notify-send notifications don't show up when I manually set the brightness/volume, so now I have to do that myself too. However, there are two problems with notify-send: The expire time option doesn't work You have to wait until a notification is finished before the next one comes up Before I overrided the brightness/volume keys, the system was able to send notifications without these two restrictions. Notifications disappeared within 3 seconds (instead of the default 10), and if I double tapped the volume or brightness button, the progress bar would immediately change to the new brightness (instead of showing the old progress bar for 10 seconds and then showing the new one). Since the system was able to do it, I was wondering how I can achieve the same type of notifications?

  Read the article

• Can't Mount Phone, "according to mtab, /dev/sdb1 is already mounted on /"

  - by RPG Master

  My myTouch Slide wasn't mounting, so I decided to open Disk Utility. My phone shows up but when I click "Mount" it gives me this error: Error mounting: mount exited with exit code 1: helper failed with: mount: according to mtab, /dev/sdb1 is already mounted on / mount failed Here's my mtab: /dev/sdb1 / ext4 rw,errors=remount-ro,commit=0 0 0 proc /proc proc rw,noexec,nosuid,nodev 0 0 none /sys sysfs rw,noexec,nosuid,nodev 0 0 fusectl /sys/fs/fuse/connections fusectl rw 0 0 none /sys/kernel/debug debugfs rw 0 0 none /sys/kernel/security securityfs rw 0 0 none /dev devtmpfs rw,mode=0755 0 0 none /dev/pts devpts rw,noexec,nosuid,gid=5,mode=0620 0 0 none /dev/shm tmpfs rw,nosuid,nodev 0 0 none /var/run tmpfs rw,nosuid,mode=0755 0 0 none /var/lock tmpfs rw,noexec,nosuid,nodev 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,noexec,nosuid,nodev 0 0 gvfs-fuse-daemon /home/matthew/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,user=matthew 0 0 /dev/sdg1 /media/Seagate\040GoFlex ext4 rw,nosuid,nodev,uhelper=udisks 0 0 EDIT: Here's my fstab: # /etc/fstab: static file system information. # # Use 'blkid -o value -s UUID' to print the universally unique identifier # for a device; this may be used with UUID= as a more robust way to name # devices that works even if disks are added and removed. See fstab(5). # # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 /dev/sda1 / ext4 errors=remount-ro 0 1 # swap was on /dev/sda5 during installation UUID=3b0db205-2bdb-4c98-a506-6bdd3520d540 none swap sw 0 0

  Read the article

• E-Business Suite - Cloning Basics & AMP Cloning - US

  - by Annemarie Provisero

  ADVISOR WEBCAST: E-Business Suite - Cloning Basics & AMP Cloning - US PRODUCT FAMILY: EBS – ATG - Utilities July 20, 2011 at 17:00 UK / 18:00 CET / 09:00 am Pacific / 10:00 am Mountain / 12:00 Eastern This 1.5-hour session is recommended for technical and functional Users who are interested to get an generic overview about the Cloning functionality available in the E-Business Suite Release. We are going to talk about the generic Cloning options and will then go into depth about the cloning scenario when using AMP (Applications Management Pack) within the Enterprise Manager. TOPICS WILL INCLUDE: Cloning Overview Rapidclone steps in Details Rapidclone limitations EM Grid Setup with AMP for Cloning Advantages of Cloning with AMP Cloning Procedures available with AMP Monitoring Clone Operation Few things to remember before Cloning A short, live demonstration (only if applicable) and question and answer period will be included. Oracle Advisor Webcasts are dedicated to building your awareness around our products and services. This session does not replace offerings from Oracle Global Support Services. Click here to register for this session ------------------------------------------------------------------------------------------------------------- The above webcast is a service of the E-Business Suite Communities in My Oracle Support. For more information on other webcasts, please reference the Oracle Advisor Webcast Schedule.Click here to visit the E-Business Communities in My Oracle Support Note that all links require access to My Oracle Support.

  Read the article

• Feasability of mobile 2D multiplayer RPG game with interactive bitmap background

  - by user2827214

  I'm looking to develop a 2D multiplayer RPG game for Android, with a bird's eye view similar to that of zelda/pokemon. The game is very simple in all ways since my intent is for thousands of players to occupy the same world which I imagine requires good performance. However, I am unsure about the performance requirements of two properties: the tile map that is used as a background is dynamic (interactive). For example, a player steps in the water, and the water turns black. Every tile in the game does this. the tile map is the same object used for all players, but it is displayed differently on each user's mobile device, even though the players exist in the same world. For example, the water that turned black is displayed as red on all other players' screens. I have knowledge of java, but almost none regarding game dev. tools. Is there a best process for these requirements? Should I develop in pure java, or use some tool like Slick2D etc.? How performance intensive are these properties, if even possible? Edit: There are no collisions in the game or difficult animations, I am imagining simply changing the colors of the tiles (like in the examples), and a client-server architecture

  Read the article

• How can I strip down Ubuntu?

  - by Thomas Owens

  I'm trying to fix what I consider a bloated install of Ubuntu. When I install Ubuntu on a machine, I get things that I don't want - web browsers, office applications, media players, accessibility utilities, Ubuntu One, and so on. My goal is to create a way that I can have an install of Ubuntu that contains only the most minimal packages - the administrative tools and package manager, a GUI (my preference would be GNOME), a text editor, core drivers (video cards, network cards - wired and wireless, input devices), and anything else that I have to have to run a stable distribution. From there, I would like to pick and choose which packages I install to create my own customized system. After playing around with other distros like Arch and Slackware, like how they provide a barebones install by default. However, I get trapped in a "configuration hell" - right now, I tried moving away from Ubuntu and to Arch, but after spending 6 hours with it, I still don't have a usable system. It's half configured and I don't have any usable software packages to enable me to work. Is anything that can help me available? Either something like the OpenSUSE builder that lets you choose applications and packages for the CD, an advanced installation mode where I can choose the packages to install and which to ignore, or a guide on how to strip Ubuntu down to its bare bones? And I suppose a natural follow up to this is once I have a stripped down Ubuntu, will this affect updating at all? When Canonical releases the next version of Ubuntu, I don't want any bloatware reinstalled. And yes, most of the applications that come with Ubuntu, I simply don't use. Ever.

  Read the article

• My boss is feuding with his boss. My workload is expanding What should I do?

  - by steve

  These two have always had a somewhat shaky relationship when they were on the same level. The other guy was recently promoted to director and now my boss reports to him. On the surface, they appear to get along when they get together, but my boss despises the man and badmouths him every chance that he gets (to peers, subordinates, etc). He believe that the director is setting him up to fail. The Director and upper management is holding my boss responsible for the not-so-great performance by the team as of late. He's been playing games to make my boss look bad. Due to lay offs, we don't have the manpower to deliever the results that we did before...but expectations have not lowered...and my boss is taking the heat for it. Now he's on the warpath and starting to micromanage. He's giving everyone more work. He's forcing us midlevel guys to take responsibility for the level one techs' performance. I'm spending less and less time coding....and more time babysitting vendors, techs, etc. I'm not so sure that's a bad thing because I'm sorta burnt out on coding, but I don't really care for the idea of having to be responsible for others poor performance....isn't that the manager's job? Anyway, do you guys have any suggestions on dealing with the situation?

  Read the article

• What's the best project management software for internal dev. 5 man shop

  - by P.Brian.Mackey

  I work for a large corporation, but we do small intranet web application development. Our project management tracking sucks. Its custom software built by a jr. intern. For what its worth, our development style is akin to agile, but there's nothing set in stone...very customer oriented approach. I need project tracking that meets the criteria: Intranet, internal products. Mostly maintenance, some new development. 5 developers 12 products 1 hands-off manager. He really just wants to know estimated man hours, due date for dev, QA and release. Along with a short description of the project. Free or super cheap. Bonus Simple pretty UI. Think pretty charts. Hope I covered everything. Please ask for any clarification. If you read dreaming in code, the company uses some project tracking software that sounds pretty sweet. Note, we do have Team Foundation Server. I already tried pushing its use as PM tracking, but its too complicated. I can't get people to sit and train. So this software has to be easy.

  Read the article

• Give Us Your Thoughts About Oracle Designs

  - by Tom Caldecott-Oracle

  Participate in the Onsite Usability Lab at Oracle OpenWorld 2014 Want to impress your colleagues? Your manager? Your mom? Imagine being able to say to them, “So, did I ever tell you about the time I helped Oracle design some of their hot applications?” Yes, that opportunity is coming up—at Oracle OpenWorld.  The Oracle Applications User Experience team will host an onsite usability lab at the 2014 conference. You can participate and give us your thoughts about proposed designs for Oracle Human Capital Management Cloud and Oracle Sales Cloud, Oracle Fusion Applications for procurement and supply chain, Oracle E-Business Suite and PeopleSoft applications, social relationship management, BI applications, Oracle Fusion Middleware, and more.  Your feedback will directly affect the usability of Oracle applications to make them intuitive, easy to use. You’ll make a difference. And that should score you points with peers, friends, and family. Of course, for your mom, first you’ll probably have to explain to her again what you do for a living. If you’re interested in participating, you must sign up in advance. Space is limited. Participation requires your company or organization to have a Customer Participation Confidentiality Agreement (CPCA) on file. Don’t have one? Let us know, and we’ll start the process. Sign up now for the onsite usability lab. When?  Monday, September 29 - Wednesday, October 1, 2014  Where?  InterContinental San Francisco Want to know about other Oracle Applications User Experience activities at Oracle OpenWorld? Visit UsableApps.

  Read the article

• How should a developer reject impossible requirements?

  - by sugar

  Here's the problem I'm facing: Quote From Project Manager: Hey Sugar, I'm assigning you the task of developing a framework that could be used for many different iOS applications. Here are the requirements: It should be able to detect the thickness of the thumb or fingers being used to manipulate the UI. With this information, all elements of the UI should be arranged & sized automatically. For a larger thumb, elements should be arranged nearer the center of the screen. For a smaller thumb, elements should be arranged nearer the corners of the screen. For a larger thumb, all fonts should be smaller. (We're assuming an adult in this case.) For a smaller thumb, all fonts should be larger. (We're assuming a younger person in this case.) Summary: This framework is required for creating user-friendly user interfaces programmatically. The framework should be developed in such a way that we can use for as many projects as needed, so it must also be very developer-friendly. I am the developer given this task, so my questions are as follows: How can I explain that these requirements are a little ridiculous? How can I explain that it would be better to concentrate on developing actual projects? How can I explain that even if this were possible, I wouldn't recommended developing such a thing? How do I say NO to this project politely, gently, and respectfully? How can I explain that even for a developer with 3 years of experience, this might not be possible?

  Read the article

• Ein besonderes Oracle Business Breakfast in Berlin

  - by Detlef Drewanz

  Seit mehreren Jahren finden bei uns Business Breakfasts statt. Diese Veranstaltung ist üblicherweise an Technologen mit tiefem technologischen Wissensdurst gerichtet. Aus einem besonderen Anlass ist die Veranstaltung am 13.6.2014 in unserem Customer Visit Center in Berlin etwas speziell. Anlässlich des Solaris 11.2 Launches tourt Herr Markus Flierl, Oracle VP Software Development, gerade durch Deutschland. Wir haben ihn nach Berlin in unser Customer Visit Center eingeladen, um mit Ihnen Ihre Cloud Strategien und Anforderungen an ein modernes Betriebssystem zu diskutieren. Vielleicht setzen Sie zurzeit ein Betriebssystem ein, welches nicht aus dem Hause Oracle stammt. Das macht nichts. Auch dann ist der Besuch zu dieser Veranstaltung interessant, denn Herr Flierl interessiert sich ebenso für Ihre Anforderungen und Entscheidungsgrundlagen. Übrigens: Markus Flierl ist in Südddeutschland geboren und aufgewachsen und spricht somit fließend Deutsch. Agenda Start Ende Titel 08:30 09:30 Registrierung und Frühstück 09:30 09:45 Begrüßung und Einleitung Ralf Zenses, Oracle Senior Director Systems Sales Consulting Europe North 09:45 11:30 Strategien für OpenStack, Software Defined Networking und RZ Automatisierung: Cloud Management Integriert, nicht nur Installiert Markus Flierl, Oracle VP Software Development 11:30 11:45 Pause 11:45 12:15 Solaris 11.2 OpenStack Demo Joost Pronk, Oracle Senior Principle Product Strategy Manager 12:15 13:00 Unified Archiving und SCAP: Die finale Antwort auf Migrations- und Compliance Fragen Detlef Drewanz, Oracle Master Principle Sales Consultant Weitere Details und den Link zur Anmeldung finden Sie hier. Die Veranstaltung ist offen für alle Interessierten. Ich freue mich auf Ihren Besuch. Wir sehen uns.

  Read the article

• Why does 12.04 upgrade abort with out of space error when I have lots of it?

  - by Kristian Thomsen

  When upgrading Ubuntu from 11.10 to 12.04 I discovered an unexpected problem. The upgrade was stopped because there wasn't enough free space for the installation. I managed to free some space and do the upgrade but now a prompt appears after logging in saying I'm out of space. This prompt asks me if I want to examine the problem. The "Disk Usage Analyser" is opened. In the top it says: Total filesystem capacity: 47.0 GB (used: 13.5 GB available: 33.4 GB) Folder -- Usage -- Size / -- 100% -- 12.5 GB usr -- 44.8 % -- 5.6 GB home -- 30.3 % -- 3.8 GB lib -- 13.0 % -- 1.6 GB var -- 9.1 % -- 1.1 GB boot 2.5 % 309.5 GB and a lot of small contributors like: etc, opt, sbin, bin etc. I do not really understand this problem since the analyser in the top says that I have 33.4 GB left in this file system. What can I do to make Ubuntu use the remaining space? Running df -i in the terminal gives: Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda7 610800 576874 33926 95% / udev 213451 563 212888 1% /dev tmpfs 218524 486 218038 1% /run none 218524 3 218521 1% /run/lock none 218524 7 218517 1% /run/shm /dev/sda8 2264752 16371 2248381 1% /home The output of df -h Filesystem Size Used Avail Use% Mounted on /dev/sda7 9,3G 7,8G 1,1G 88% / udev 993M 4,0K 993M 1% /dev tmpfs 401M 884K 400M 1% /run none 5,0M 0 5,0M 0% /run/lock none 1003M 152K 1002M 1% /run/shm /dev/sda8 35G 4,0G 29G 13% /home /dev/sda2 101G 64G 37G 64% /media/A2C8E28BC8E25CD3 Running sudo fdisk -l gives Disk /dev/sda: 160.0 GB, 160041885696 bytes 255 heads, 63 sectors/track, 19457 cylinders, total 312581808 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000080 Device Boot Start End Blocks Id System /dev/sda1 63 96389 48163+ de Dell Utility /dev/sda2 * 98304 210434488 105168092+ 7 HPFS/NTFS/exFAT /dev/sda3 210436094 312576704 51070305+ f W95 Ext'd (LBA) /dev/sda5 306279288 312576704 3148708+ dd Unknown /dev/sda6 210436096 214341631 1952768 82 Linux swap / Solaris /dev/sda7 214343680 233873407 9764864 83 Linux /dev/sda8 233875456 306278399 36201472 83 Linux Partition table entries are not in disk order

  Read the article

• LiveCD Boot/Install

  - by Jon

  I have recently built a new computer and have been looking to dual-boot alongside Windows. Trying to boot/install off Ubuntu/Dedora/Arch live CDs has failed across all distros and I keep getting the error: [34.5173939] ata9.00: exception Emask 0x52 SAct 0x1 SErr 0xffffffff action 0xe frozen [34.517403] ata9: SError: {RecovData RecovComm UnrecovData Persist Proto HostInt PHYRdyChg PHYInt CommWake 10B8B Dispar BadCRC Handshk LinkSeq TrStaTrns UnrecFIR DevExch } [34.517413] ata9.00: failed command: READ FPDMA QUEUED [34.517420] ata9.00: cmd 60/08:00:00:6d:70/00:00:74:00:00/40 tag 0 ncq 4096 in [34.517420] res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x56 (ATA bus error) [34.517433] ata9.00: status: { DRDY } [34.667134] ata10.00 exception Emask 0x52 SAct 0x1 SErr 0xffffffff action 0xe frozen [34.667134] ata10: SError: {RecovData RecovComm UnrecovData Persist Proto HostInt PHYRdyChg PHYInt CommWake 10B8B Dispar BadCRC Handshk LinkSeq TrStaTrns UnrecFIR DevExch } [34.667153] ata10.00: failed command: IDENTIFY PACKET DEVICE [34.667159] ata10.00: cmd a1/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [34.667160] res 40/00:01:00:00:00/00:00:00:00:00/00 Emask 0x56 (ATA bus error) [34.667170] ata10.00: status: { DRDY } I am using a new ASUS Z77 Sabertooth motherboard with a Seagate Barracuda ST1000DM003 1TB 7200RPM hard drive. I am not entirely sure why I can't even boot off the live CD? Any ideas? Hi thanks for the quick response. All Distros were direct download from their respective websites, I have tried both CD boot with all distros and USB boot with Arch only. I have just updated my BIOS as well an am still receiving the same error. The fact that it happens on CD and USB tell's me it's not an optical drive issue. All information I can find on this seems to relate to hard drives failing on already installed linux boxes or faulty SATA cables. I am a bit confused why this issue would be preventing a CD/USB boot though. Is there any more info I can provide that might help uncover the source of the problem? Cheers, Jon

  Read the article

• Reboot failure after upgrade from 8.04 LTS to 10.04 LTS

  - by Alan Fietz

  I bought our computer from Freegeeks with Ubuntu 8.04 installed. I upgraded from Ubuntu 8.04 to 10.04 on Thursday November 10. I have an ASUS P4P800SE with dual Intel P4@3GHZ. Installation messages were: - Error loading Nautilus config info - Replaced customied /etc/login.defs - Replaced customized /etc/dhcp3/dhclient.conf - 189 packages removed - WARNING: Failed to read mirror file When I rebooted, the usual ASUS screen appeared, then "Loading GRUB" then "starting Up..." then "starting Up..." again then a blank screen (the moniter went dormant). I rebooted, started GRUB and selected: version 10.04.3 LTS kernel 2.6.32-35 generic I got the same results. I rebooted, started GRUB and selected: kernel 2.6.24-29 generic Here's what was displayed: udevd [875]: error getting socket: Invalid argument libudev:udev_monitor_new_from_netlink: error getting socket: Invalid argument Segmentation fault **Gave up waiting for root device** Common problems - Boot args (cat/proc/cmdline) - Check root delay - check root - Missing modules (cat/pro/modules; **Alert! /dev/disk/by_vvid/c59c6361 etc... does not exist. Dropping to a shell.** Then Busybox v1.13.3 started with the following prompt (?) (initramfs) _ But my typing did not appear on the screen. It appears the hard drive cannot be found. Any suggestion on how to remedy this? Thank you.

  Read the article

• Java Not Recognized As Default Application

  - by John

  I just installed java according to this article, and 'java -version' displays java version "1.7.0_07" Java(TM) SE Runtime Environment (build 1.7.0_07-b10) Java HotSpot(TM) 64-Bit Server VM (build 23.3-b01, mixed mode) 'update-alternatives --config java' returns this: There are 2 choices for the alternative java (providing /usr/bin/java). Selection Path Priority Status ------------------------------------------------------------ 0 /usr/bin/gij-4.6 1046 auto mode 1 /usr/bin/gij-4.6 1046 manual mode * 2 /usr/local/java/jdk1.7.0_07/bin/java 1 manual mode Press enter to keep the current choice[*], or type selection number: with update-alternatives --config javac (or javaws) returning similarly. however java isn't listed in the default applications menu when I click on a .jar file and go to "open with application". I tried to install java this way, and on the update-alternatives part of the command returned me: /etc/alternatives/[java,javac,javaws] is dangling, it will be updated with best choice I just confirmed that I can use java, as 'java -jar file.jar' does work. Just figured that I'd mention it, don't know why I didn't before, but when I right click on a .jar file, java 7 run-time isn't even listed there, it seems that the file-manager isn't recognizing it as a program, but it is there, and it does work...

  Read the article

• Bad DMA/do_IRQ errors on suspend/resume, with occasional freezing

  - by Steve Kroon

  Every time I suspend or resume my laptop (Dell Latitude E6520, bought this year), I get 2 messages of the form displayed on the console just before shutting down/starting up: [ 407.107610] ehci_hcd 0000:00:1d.0: dma_pool_free buffer-128, f6f18000/36f18000 (bad dma) On occasion, I get a message of the form: [ 3753.979066] do_IRQ: 0.177 No irq handler for vector (irq -1) On occasion, my machine freezes with a flashing Caps Lock button when suspending, after which I need to do a hard shutdown. This never happened before the messages started appearing (a while back), and I think it never happens without a do_IRQ message appearing (although I'm not sure about that). [There's nothing in the owner's manual on a flashing Caps Lock button; apparently it may be a kernel panic if the scroll lock also flashes, but the laptop doesn't have a scroll lock light, and there's no message on the console saying kernel panic.] Are these bad DMA/do IRQ messages serious, and what can I do to investigate/troubleshoot them and the freezing? Edit: I've also now received the following error messages a few times: [246943.023908] JBD: I/O error detected when updating journal superblock for sdb1. [246943.023958] Buffer I/O error on device sdb1, logical block 0 [246943.023996] EXT3-fs (sdb1): I/O error while writing superblock Edit: Output of dmesg at http://pastebin.com/ra7MTQEj ; contents of /var/log/kern.log at http://pastebin.com/i6jf0Md9 Edit: the output of some smartctl (-a, -x, --log=error, --log=xerror) instructions is available at http://paste.ubuntu.com/1088488/ . Edit (31/8/2012): Output of dmesg|grep -i ehci available at http://paste.ubuntu.com/1177246/ .

  Read the article

• Attend my Tech Ed 2014 session: Debugging Tips and Tricks

  - by Daniel Moth

  Just a week away, at Tech Ed 2014 NA in Houston Texas, I will be giving a demo presentation that you will not want to miss (assuming you code in Visual Studio). Add it to your calendar now: DEV-B352 Debugging Tips and Tricks in Visual Studio 2013 (link) Monday, May 12 1:15-2:30 PM, Room: General Assembly C As a developer, regardless of your programming language or the platform that you target, you use the debugger on a daily basis. Come to this all-demo session to learn how to make the most of the Visual Studio debugger, and hence be more productive and effective in your everyday development. We tour almost all of the debugger surface and many of its commands, throwing in tips and tricks as we go along, and also calling out what is brand new in the latest version of the debugger in Microsoft Visual Studio 2013. Whatever your experience level, you are guaranteed to leave with new knowledge of debugger features that you will want to use immediately when you are back at your computer!   I am also co-presenting another session later in the week. DEV-B313 Diagnosing Issues in Windows Phone 8.1 XAML Applications Using Visual Studio 2013 (link) Thursday, May 15 10:15-11:30 AM, Room: 340 Come to this demo-driven session to learn how to use the latest diagnostic tools in Visual Studio 2013 to make your Windows Phone 8.1 XAML apps reliable, fast, and efficient. Learn how to make the most of existing capabilities in the debugger as well as new debugging features for diagnosing correctness issues. Also, see the Visual Studio Performance and Diagnostics hub in action with its performance analysis tools for diagnosing CPU usage, memory usage, and energy consumption. The techniques covered in this session apply equally well for Windows Store apps as well as Windows Phone Store apps, so all your device development needs will be covered.   Links to both sessions from my Tech Ed speaker page. See you there! Comments about this post by Daniel Moth welcome at the original blog.

  Read the article

• How to fix a Broadcom 43224 (rev. 01) in ubuntu 12.10, running on a macbook pro 6,2?

  - by Eduardo Bezerra

  I've googled for 3 days so far, with no success, so I'll be straightforward: How do you get it to work? this is the output for lspci -v: 03:00.0 Network controller: Broadcom Corporation BCM43224 802.11a/b/g/n (rev 01) Subsystem: Apple Inc. Device 0093 Flags: bus master, fast devsel, latency 0, IRQ 17 Memory at c1b00000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: bcma-pci-bridge Kernel modules: bcma for uname -a: Linux fury 3.5.0-17-generic #28-Ubuntu SMP Tue Oct 9 19:31:23 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux I've tried with bcmwl-kernel-source, firmware-b43-installer and now I'm out of ideas. Can someone help me? This is driving me insane! EDIT: for lspci -nn | grep 0280: 03:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) I can see the networks available, but when I try to connect, it gets stuck in a loop: tries to connect, fails, tries again, fails again and so on... EDIT 2: After a long break from this problem, I've just run a few tests again and found out that, although my macbuntu still fails to connect to my home wi-fi network, it works just fine at my university... Does that help in anyway? My home network is managed by a dual-band (2.4Ghz and 5Ghz) 802.11n cisco e4200 wi-fi router.

  Read the article

• Best of OTN - Week of August 17th

  - by CassandraClark-OTN

  Architect CommunityThe Top 3 most popular OTN ArchBeat video interviews of all time: Oracle Coherence Community on Java.net | Brian Oliver and Randy Stafford [October 24, 2013] Brian Oliver (Senior Principal Solutions Architect, Oracle Coherence) and Randy Stafford (Architect At-Large, Oracle Coherence Product Development) discuss the evolution of the Oracle Coherence Community on Java.net and how developers can actively participate in product development through Coherence Community open projects. Visit the Coherence Community at: https://java.net/projects/coherence. The Raspberry Pi Java Carputer and Other Wonders | Simon Ritter [February 13, 2014] Oracle lead Java evangelist Simon Ritter talks about his Raspberry Pi-based Java Carputer IoT project and other topics he presented at QCon London 2014. Hot Features in Oracle APEX 5.0 | Joel Kallman [May 14, 2014] Joel Kallman (Director, Software Development, Oracle) shares key points from his Great Lakes Oracle Conference 2014 session on new features in Oracle APEX 5.0. Friday Funny from OTN Architect Community Manager Bob Rhubart: Comedy legend Steve Martin entertains dogs in this 1976 clip from the Carol Burnette show. Database Community OTN Database Community Home Page - See all tech articles, downloads etc. related to Oracle Database for DBA's and Developers. Java Community JavaOne Blog - JRuby and JVM Languages at JavaOne!  In this video interview, Charles shared the JRuby features he presented at the JVM Language Summit. He'll be at JavaOne read the blog to see all the sessions. Java Source Blog - IoT: Wearables! Wearables are a subset of the Internet of Things that has gained a lot of attention. Learn More. I love Java FaceBook - Java Advanced Management Console demo - Watch as Jim Weaver, Java Technology Ambassador at Oracle, walks through a demonstration of the new Java Advanced Management Console (AMC) tool. Systems Community OTN Garage Blog - Why Wouldn't Root Be Able to Change a Zone's IP Address in Oracle Solaris 11? - Read and learn the answer. OTN Garage FaceBook - Securing Your Cloud-Based Data Center with Oracle Solaris 11 - Overview of the security precautions a sysadmin needs to take to secure data in a cloud infrastructure, and how to implement them with the security features in Oracle Solaris 11.

  Read the article

• Odd Android touch event problem

  - by user22241

  Overview When testing my game I came across a bizarre problem with my touch controls. Note this isn't related to multi-touch as I completely removed my ACTION_POINTER_UP and ACTION_POINTER_DOWN along with my ACTION_MOVE code. So I'm simply working with ACTION_UP and ACTION_DOWN now and still get the problem. The problem I have a left and right button on the left of the screen and a jump button on the right. Everything works as it should but if I touch a large area of my hand (the fleshy part at the base of the thumb for instance) onto the screen, then release it and then press one of my arrows, the sprite moves in that direction for a few seconds, and then ACTION_UP is mysteriously triggered. The sprite stops and then if I release my finger and re-apply it to an arrow, the same thing happens. This goes on and on and eventually (randomly??) stops and everything work OK again. Test device & OS Google Nexus 10 Tablet running Jellybean 4.2.2 Code //Action upon which to switch actionMask = event.getActionMasked(); //Pointer Index of the currently touching pointer pointerIndex = event.getActionIndex(); //Number of pointers (for multi-touch) pointerCount = event.getPointerCount(); //ID of the pointer currently being processed (Multitouch) pointerID = event.getPointerId(pointerIndex); switch (actionMask){ //Primary pointer down case MotionEvent.ACTION_DOWN: { //if pressing left button then set moving left if (isLeftPressed(event.getX(), event.getY())){ renderer.setSpriteLeft(); } //if pressing right button then set moving right else if (isRightPressed(event.getX(), event.getY())){ renderer.setSpriteRight(); } //if pressing jump button then set sprite jumping else if (isJumpPressed(event.getX(),event.getY())){ renderer.setSpriteState('j', true); } break; }//End of case //Primary pointer up case MotionEvent.ACTION_UP:{ //When finger leaves the screen, stop sprite's horizontal movement renderer.setSpriteStopped(); break; }

  Read the article

• What methods should save/load a game state

  - by vedi

  There are a lot of articles about how to save a state of a game and they are pretty good. But I have one conceptual misunderstanding where should I save the state? My game has number of screens and pair of them are MainMenuScreen and MainSceneScreen these are inherited from Screen class. MainMenuScreen is shown at start of the game the MainSceneScreen little later. What is the problem? I navigated to MainSceneScreen, forced Android to stop the application (I change a language settings on the device to achieve it, please let me know if I'm wrong). After that I select the application again and I can see MainMenuScreen is shown. But I want MainSceneScreen to be shown. I suppose I should override resume method. But what class I should override? I have class PsGame that extends Game class of libgdx. I put breakpoints to its resume method and it turned out that method was not called. I investigated the problem and I've found little strange code in onResume method of AndroidApplication class of libgdx: if (!firstResume) graphics.resume(); else firstResume = false; My debugger said firstResume was true and didn't go to *graphics.resume()*line. Sorry for a lot of words but could you answer following question: What did I do wrong? What methods should I override? Thank you in advance.

  Read the article

• What I saw at TechEd North America 2014

  - by Brian Schroer

  Originally posted on: http://geekswithblogs.net/brians/archive/2014/05/19/teched-north-america-2014.aspxI was thrilled to be able to attend TechEd North America 2014 in Houston last week. I got to go to Orlando in 2008, and since then I’ve had to settle for watching the sessions online (which ain’t bad – They’re all available on Channel 9 for streaming or downloading. Here are links to the Developer Track sessions and to the sessions from all tracks.) The sessions I attended (with my favorites bolded) were: Shiny new stuff The Microsoft Application Platform for Developers: Create Applications That Span Devices and Services INTRODUCING: The Future of .NET on the Server DEEP DIVE: The Future of .NET on the Server ASP.NET: Building Web Application Using ASP.NET and Visual Studio The Next Generation of .NET for Building Applications The Future of Visual Basic and C# Stuff you can use now Building Rich Apps with AngularJS on ASP.NET Get the Most Out of Your Code Maps SignalR: Building Real-Time Applications with ASP.NET SignalR Performance Optimize Your ASP.NET Web App Modern Web and Visual Studio Visual Studio Power User: Tips and Tricks Debugging Tips and Tricks in Visual Studio 2013 In a world where the whole company uses TFS… Using Functional, Exploratory and Acceptance Testing to Release with Confidence A Practical View of Release Management for Visual Studio 2013 From Vanity to Value, Metrics That Matter: Improving Lean and Agile, Kanban, and Scrum Ain’t Nobody Got Time for That As usual, there were some time slots with nothing of interest and others with 5 things I wanted to see at the same time. Here are the sessions I’m still planning to watch… Getting Started with TypeScript Building a Large Scale JavaScript Application in TypeScript Modern Application Lifecycle Management Why a Hacker Can Own Your Web Servers in a Day! Async Best Practices for C# and Visual Basic Building Multi-Device Apps with the New Visual Studio Tooling for Apache Cordova Applying S.O.L.I.D. Principles in .NET/C# Native Mobile Application Development for iOS, Android, and Windows in C# and Visual Studio Using Xamarin Latest Innovations in Developing ASP.NET MVC Web Applications Zero to Hero: Untested to Tested with Microsoft Fakes Using Visual Studio Cool and Elegant ASP.NET Web Forms with HTML 5 for the Modern Web The Present and Future of .NET in a World of Devices and Services

  Read the article

• What's the best algorithm for... [closed]

  - by Paska

  Hi programmers! Today come out a little problem. I have an array of coordinates (latitude and longitude) maded in this way: [0] = "45.01234,9.12345" [1] = "46.11111,9.12345" [2] = "47.22222,9.98765" [...] etc In a loop, convert these coordinates in meters (UTM northing / UTM easting) and after that i convert these coords in pixel (X / Y) on screen (the output device is an iphone) to draw a route line on a custom map. [0] = "512335.00000,502333.666666" [...] etc The returning pixel are passed to a method that draw a line on screen (simulating a route calculation). [0] = "20,30" [1] = "21,31" [2] = "25,40" [...] etc As coordinate (lat/lon) are too many, i need to truncate lat/lon array eliminating the values that doesn't fill in the map bound (the visible part of map on screen). Map bounds are 2 couple of coords lat/lon, upper left and lower right. Now, what is the best way to loop on this array (NOT SORTED) and check if a value is or not in bound and after remove the value that is outside? To return a clean array that contains only the coords visible on screen? Note: the coords array is a very big array. 4000/5000 couple of items. This is a method that should be looped every drag or zoom. Anyone have an idea to optimize search and controls in this array? many thanks, A

  Read the article

• EBS Seed Data Comparison Reports Now Available

  - by Steven Chan (Oracle Development)

  Earlier this year we released a reporting tool that reports on the differences in E-Business Suite database objects between one release and another.  That's a very useful reference, but EBS defaults are delivered as seed data within the database objects themselves. What about the differences in this seed data between one release and another? I'm pleased to announce the availability of a new tool that provides comparison reports of E-Business Suite seed data between EBS 11.5.10.2, 12.0.4, 12.0.6, 12.1.1, and 12.1.3.  This new tool complements the information in the data model comparison tool.  You can download the new seed data comparison tool here: EBS ATG Seed Data Comparison Report (Note 1327399.1) The EBS ATG Seed Data Comparison Report provides report on the changes between different EBS releases based upon the seed data changes delivered by the product data loader files (.ldt extension) based on EBS ATG loader control (.lct extension) files.  You can use this new tool to report on the differences in the following types of seed data: Concurrent Program definitions Descriptive Flexfield entity definitions Application Object Library profile option definitions Application Object Library (AOL) key flexfield, function, lookups, value set definitions Application Object Library (AOL) menu and responsibility definitions Application Object Library messages Application Object Library request set definitions Application Object Library printer styles definitions Report Manager / WebADI component and integrator entity definitions Business Intelligence Publisher (BI Publisher) entity definitions BIS Request Set Generator entity definitions ... and more Your feedback is welcomeThis new tool was produced by our hard-working EBS Release Management team, and they're actively seeking your feedback.  Please feel free to share your experiences with it by posting a comment here.  You can also request enhancements to this tool via the distribution list address included in Note 1327399.1.Related Articles Oracle E-Business Suite Release 12.1.3 Now Available New Whitepaper: Upgrading EBS 11i Forms + OA Framework Personalizations to EBS 12 EBS 12.0 Minimum Requirements for Extended Support Finalized Five Key Resources for Upgrading to E-Business Suite Release 12 E-Business Suite Release 12.1.1 Consolidated Upgrade Patch 1 Now Available New Whitepaper: Planning Your E-Business Suite Upgrade from Release 11i to 12.1

  Read the article

< Previous Page | 527 528 529 530 531 532 533 534 535 536 537 538  | Next Page >