Search Results

Search found 22546 results on 902 pages for 'mode management'.

Page 585/902 | < Previous Page | 581 582 583 584 585 586 587 588 589 590 591 592  | Next Page >

• Battery notification always showing 'xx% remaining' with Windows 7 on an acer Aspire 5590

  - by dindeman

  My battery level always shows up as something like 55% remaining or 63% remaining ...etc despite that it is in fact charging. Additionally it doesn't go any further than 80% remaining even if I keep it in charge forever. This leads me to a side annoying effect which is that I cannot proceed to install Windows 7 Service Pack 1 as its installer requires the laptop to be plugged with a power cord. My laptop is plugged with the power cord but because of the above issue (it doesn't display anything else than the xx% remaining) Windows thinks that the laptop is using its battery and that the power cord is disconnected. I have installed the original acer ePower Management tool that let you configure the power scheme... etc, I was hoping that this would help me circumvent the 80% issue but it doesn't.

  Read the article

• Ubuntu server 12.04.03 not checking disk partitions on reboot?

  - by jamesc

  My MOTD is showing: *** /dev/md2 will be checked for errors at next reboot *** *** /dev/md1 will be checked for errors at next reboot *** *** /dev/md3 will be checked for errors at next reboot *** However, a standard sudo shutdown -r now does not appear to check the disks and the message remains. My guess is that the partitions 'should' be checked and that they are not being... so how can I get Ubuntu to check the partitions at reboot and keep things nice and safe? Update - this is the output of cat /etc/fstab proc /proc proc defaults 0 0 none /dev/pts devpts gid=5,mode=620 0 0 /dev/md/0 none swap sw 0 0 /dev/md/1 /boot ext3 defaults 0 0 /dev/md/2 / ext4 defaults 0 0 /dev/md/3 /home ext4 defaults 0 0 Update 2 - One message gone... Using @christianwolff's suggestions... sudo rm /var/lib/update-notifier/fsck-at-reboot sudo touch /forcefsck sudo shutdown -r now And now the motd is down to *** /dev/md1 will be checked for errors at next reboot *** *** /dev/md3 will be checked for errors at next reboot *** So 'md2(ext4)' has been checked and the message updated.

  Read the article

• Windows Vista to Windows7 upgrade

  - by Kalls

  I have a Windows Vista Home Premium and I tried installing SP2 on it and It prompted me to install SP1. Then it stopped working when I installed SP1. I don't have back up that I can use to restore it. When I use the Windows Repair mode I am unable to get access to few options none of which is working. I do have access to the command prompt. Is there way to restore this? If I am planning to upgrade to Windows 7 Home Premium what are the steps?

  Read the article

• Troubleshooting an iMac

  - by Matthew

  What can I do to fix my iMac? When I start it up, it just loads forever (never getting to the Desktop). The mouse will appear then disappear, then the loading bar will sometimes appear and then disappear and it just goes in circles forever. If I start up in safe mode (by holding shift), it gets to the login window. However, if I attempt to log in the login window disappears and reappears asking for my password again. What can I do to troubleshoot this?

  Read the article

• Remotely start VNC server on computer with no Admin password

  - by Joe M.

  I'm trying to remotely access a particular computer of mine and it seems that VNC has stopped. I can tell that the computer is still running because I can VNC into another machine on the same network and can see my target machine under the Network section in Windows Explorer and can also ping it succesfully. To summarize: I own the target computer I am currently too far to physically access it Remote Desktop Connection feature of Windows is not enabled The computer normally runs a VNC server, but it seems to have stopped The computer is definitely on and connected to the network The computer has no password on the Admin account I can VNC into other computers on the same LAN Given these conditions how can I get into the target to open VNC server, or even just reboot the target (VNC should open on startup)? I have tried PsExec and get "access is denied", and also tried "Connect to another computer.." from the Computer Management console and also get "access is denied".

  Read the article

• Installing Windows on multiple computers

  - by Rob

  At our work we've decided to buy SSDs to speed up our computers. We'd also like to upgrade from Windows 7 to Windows 8.1 (read clean install) I'm talking about 10 computers which going to have a fully clean installation. Is there any trick I can use to avoid installing Windows 10 times? The computers (most of them) are different in hardware, so I think duping is no good option. What can I do? I'd like to spend as less time as possible because all computers are going to need SQL Management Studio and Visual Studio 2012/2013. Thanks!

  Read the article

• Windows 8.1 will not go back to sleep after waking up

  - by per

  I have problems putting Windows to sleep and starting the screen saver on my new Windows 8.1 machine. Sleep mode and screen savers work only when the computer is first powered up (or restarted). But once it goes to sleep (manually or automatically) and I wake it up later, it wont go back to sleep again and I can't use screen savers either. I updated the chipset and graphics card drivers. My computer isn't part of a homegroup either. Does anyone else have similar issues? Thanks for your advice, per

  Read the article

• Default maximum heap size -- Ubuntu 10.04 LTS, openjdk6-jre

  - by sachin

  I just installed openjdk6-jre on Ubuntu 10.04 java version "1.6.0_20" OpenJDK Runtime Environment (IcedTea6 1.9.2) (6b20-1.9.2-0ubuntu1~10.04.1) OpenJDK 64-Bit Server VM (build 19.0-b09, mixed mode) Every time I run "java" I get this error: Error occurred during initialization of VM Could not reserve enough space for object heap Could not create the Java virtual machine. This can be solved by specifying a maximum heap size and running "java -Xmx256m" But is there anyway to permanently fix this error (i.e. set the default heap size to 256MB so that I do not need to specify the max heap size every time I run the command)

  Read the article

• "Device Not Ready" when attempting to connecting an old (DOS) hard drive to windows 7

  - by Christopher Vigliotti

  I have an old Western Digital Caviar 2540 hard drive that I am attempting to connect to a Windows 7 machine by using a Bytecc BT-300 USB 2.0 to IDE/SATA Adapter. I'm connecting things in the right order (power, then sata, then usb) and the jumper settings on the drive are at present set to slave, but am still having an issue. I am recieving a message that the drive is not initialized. When I go into Computer Management I can see the drive (as "Disk 5, Unknown, Not Initialized"), but when I attempt to initialize it or right-click and select "Offline" It tells me that "the device is not ready". Is there something that I can to to get around this, connect the drive and copy the data that I need off of this drive? Is there a third party tool available that I can use?

  Read the article

• Skype prevents computer from idling?

  - by Corey Sarnia

  When using Skype, it prevents the computer from idling, going into sleep mode and turning the monitor off. I notice on my laptop if I use a tool like Monitor Off to manually turn my monitor off, after about a minute, the monitor will come back on as if Skype has pressed a key or moved my mouse to exit out of that idle state. This also prevents other programs (such as Pidgin) from going idle as well, so it looks like I'm online 24/7... even though it should be going idle after 5 minutes of inactivity. Is there a way to circumvent this behavior in Skype?

  Read the article

• My Windows 7 computer is stuck in a refresh rate not supported by my display. How can I fix this?

  - by Tim Keating

  Star Wars: The Old Republic apparently decided that my screen res should be 1680x1050 at 75hz. I have an older monitor that doesn't support that refresh rate. I fixed this problem within the game, but subsequently I alt-tabbed out of the game to the desktop & it reset me to those settings. Now my monitor shows a blank screen with "out of range" in Windows, and these settings persist even through a reboot. I booted into safe mode, but of course while there, I can only change the settings for the default driver. How can I get my machine back into a usable state?

  Read the article

• Resolution of monitor is not supported by motherboard

  - by Sandesh

  I have Desktop with configuration Pentium 4,945 intel chipset board,dual booting with win 7 and ubuntu 10.10 (no graphics card) Recently i purchased Dell IN2020M 20" with native resolution of 1600x900 but my display allow maximum of 1024x768 because of this when i play any video in full screen mode it doesn't play smoothly or frames are refreshed jerkily I have tried updating my VGA driver but its doesn't helping me much. Is there any way to solve this problem ? 1if i want to replace monitor what maximum resolution should i buy ? 2if i want to upgrade(graphics card/motherboard) my desktop what is the minimum configuration to support the current system. Thanks in advance

  Read the article

• How to cleanup tmp folder safely on Linux

  - by Syncopated

  I use RAM for my tmpfs /tmp, 2GB, to be exact. Normally, this is enough but sometimes, processes create files in there and fail to cleanup after themselves. This can happen if they crash. I need to delete these orphaned tmp files or else future process will run out of space on /tmp. How can I safely garbage collect /tmp? Some people do it by checking last modification timestamp, but this approach is unsafe because there can be long-running processes that still need those files. A safer approach is to combine the last modification timestamp condition with the condition that no process has a file handle for the file. Is there a program/script/etc that embodies this approach or some other approach that is also safe? Incidentally, does Linux/Unix allow a mode of file opening with creation wherein the created file is deleted when the creating process terminates, even if it's from a crash?

  Read the article

• USB HD Freezes Windows Explorer

  - by nfplee

  I recently purchased a "Seagate STBX1000200 1TB Expansion 2.5 inch External Hard Drive". It has been working without problems until recently. When i plug the device into a USB port the device is recognised as it appears in the device manager but when i go to Windows Explorer and try to open it (or right click on it) it hangs/freezes windows explorer. Please note i am using Windows 7 Professional. I have already tried various things without success after searching for people with similar problems. I did read that it could be a problem with how the computer assigns a drive letter. But whrn i go to disk management (when running as an administrator) it hangs and displays the following message: Connecting to virtual disk service I'd appreciate it if anyone could offer some advice. Thanks

  Read the article

• How do I set up two existing disks with identical contents as a single mirrored volume in Windows 7 without losing data?

  - by Software Monkey

  I have two data disks that were, heretofore, in a mobo RAID configuration in Windows 7. They are now separate AHCI disks, visible in Computer Management. How to I go about making them a single mirrored volume in Windows? Note: The data is backed up up on two other separate disks, but it's a fair amount of work to do a restore (over 120'000 files, and I have to reset permissions). Note2: Currently the two disks are identical, and I can use the content of either one for this.

  Read the article

• Looking for an open source real-time network analysis program

  - by JrSysAdmin

  Can somebody recommend an open source real-time network analysis program? What I'm looking for the program to do is display a graph of bandwidth usage by IP within our internal network that can quickly be viewed any time we need to (typically when we want to quickly find out who is utilizing high amounts of bandwidth and slowing down the network). We ideally simply want to hook up a monitor on the wall of our server room to a system whose NIC will be in permissive mode to log all network activity in a visual manner which can easily be seen and running 24/7. Prefer open source as I do not have a budget for this project and prefer open source projects in general. I'd also prefer for this to be available for CentOS but any linux distro or Windows OS would be acceptable. Thanks!

  Read the article

• What's better for deploying a website + DB on EC2: 2 small VM or a large one?

  - by devguy

  I'm planning the deployment of a mid-sized website with a SQL Server Standard DB. I've chosen Amazon EC2 to deploy it. I now have to choose between these 2 options: 1) get 2 small instances (1 core each, 1.7 GB of ram each): one for the IIS front-end, one for running the DB. Note: these "small instances" can only run the 32-bit version of Win2008 Server 2) a single large instance (4 cores, 7.5 gb of ram) where I'd install both IIS and the SQL Server. Note: this large instance can only run the 64-bit version of Win2008 Server What's better in terms on performance, scalability, ease of management (launch up a new instance while I backup the principal instance) etc. All suggestions and points of view are welcome!

  Read the article

• Vlan Tagging at Access Port in Switch

  - by singh

  I'm Confused from the fact that Vlan tagging is done at access port and trunk port always gets tagged packets (until its case of native vlan).But I still believe in other fact which says tagging happen only when a frame hit the trunk port which means trunk port gets untagged frame and tagging is not possible at access port. Would like to know where actually this tagging happens ? and also which command we can use to encapsulate 802.1q protocol to access port ? The way we do at trunk port is switchport trunk encapsulation dot1q Is the above command applicable for access mode also?

  Read the article

• Apache configuration file visualization/testing

  - by Matt Holgate

  Is there a tool available (or a debug mode built into Apache) that will allow me to interactively test and explain an Apache configuration for a given request? In particular, I'd like to be able to see which directives will apply when requesting a specific URL. For example, the output for the URL http://myserver.com/foo/bar/bar.html might look something like: Allow from 192.168.0.3 <-- From <Location /foo/bar> in myserver.com vhost Require valid user <-- From <Directory /var/www/foo> in global configuration Satisfy any <-- From <File bar.html> in global configuration [Background: why do I want this? The apache merging rules for configuration directives are quite complex to get right. It would be great to have a tool which allows you to check that your rules are doing exactly what you want, and would be a good learning tool]. If there isn't such a tool, is there a debug option in Apache that will log such information for each incoming request?

  Read the article

• exim sending mail to wrong mail server

  - by Chris Bull

  I have recently taken over management of a server running centos and whm. It has several websites and domains running under reseller accounts. Email has always been on a server at our actual office. I have recently changed our email from our local email server to gapps for business (our local email server was pretty archaic). However, when any email is sent from the web server (such as wordpress etc) to our domain - it still routes it to the IP of our old email server. I am not very familiar with WHM or exim so don't really know how to address this. Email to other domains works fine and the gapps is working perfectly. Any help is much appreciated.

  Read the article

• Ubuntu not showing hard drive

  - by ojek

  I have a laptop which had a broken installation of Windows 7 installed on it. I created a Ubuntu live USB and tried installing Ubuntu over that Windows 7. After a few minutes, I got an error message, so I needed to restart the computer. Now the laptop says that there is no bootable device - reasonable message given that there was an error during Linux installation. However: BIOS can see my hard drive, When I start Ubuntu in live mode, and try either sudo fdisk -l or gparted, it doesn't show any hard disk drives. I am 90% sure that the hard drive is broken, but it is weird that BIOS can see it, and Ubuntu doesn't. How can I be 100% sure about that hard drive? Is there any additional way of detecting my hard drive from Ubuntu?

  Read the article

• How do I set Windows 7 as default OS but retain Windows 8 Boot screen?

  - by PJC

  I am dual-booting between Windows 7 and Windows 8 on a test workstation, and typically reboot 3-4 times per day. If I set Windows 8 as the default OS, I get the Windows 8 graphical boot screen, which is easy to 'see' during the boot process, but if I set Windows 7 as the default OS, I only get the Windows 7 text-mode boot screen. While I mostly want Windows 7 (at the moment), on the occasions I restart to get to Windows 8, I often 'miss' seeing the text-only boot and have to restart twice. Is it possible to (and if so, how do I) configure this such that Windows 7 is the default OS, but still having the Windows 8 boot screen appear? Edit: Just so you guys know, I've tried setting Windows 7 as the default both from the Windows 8 Boot screen itself, and from within Windows 8 -- neither of these have the desired effect.

  Read the article

• Is there a pressure sensitive stylus for windows 8 power capacitative screen devices?

  - by JohnnyM

  I own a Dell XPS 12 Duo (filp-screen ultrabook with 10-point cap. screen) with Windows 8. Note: The ultrabook has Bluetooth 4.0. I would really love to have a preassure sensitive stylus that I could use to draw on the capacitative screen, when in tablet mode. So far I couldn't find any that would be compatible with Windows 8, maybe you guys could help. Must have: works with capacitative screen windows 8 compatible pressure sensitive Important: thin tip Nice to have: palm rejection tilt sensitive extra buttons (lots of them) TIA

  Read the article

• Windows 8: User profile service service failed the login. User Profile can not be loaded

  - by Ryanmt

  I removed accounts that were hosted on a separate drive before upgrading to windows 8 from 7 yesterday. However, now I get the User profile service service failed the login. User Profile can not be loaded. error whenever I try to access any new account. I've attempted it: from safe mode (suggestions here ) net user test \ADD Editing the permissions on the %sysdrive%\Users\Default folder to ensure it is readable Every attempt is met with the same error. Additionally, I do not see any new entries created in the HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList registry entry. I'm not sure I understand why a failed user creation wouldn't trigger an error... but that seems to be what is happening here.

  Read the article

• Computer hanged in the middle of bios flashing process

  - by Stalker

  I have a laptop: Toshiba Satellite c660-17j, today I decided to update BIOS. I've downloaded bios updater from manufacturer's web site, and in the middle of flashing process computer hanged. I was waiting more than 30 minutes, but nothing was changed on the screen, i've tryed to PRESS MORE BUTTONS, but there were no reactions, so i've turned it off by removing battery (all other methods failed, even pressing power button for ~10 secs). After that computer can't start. I understand, that there's MESS in BIOS chip, and it's possible to re-flash it with hardware programmer, but I don't have it. I remember, that on some PCs (even on my eeepc) there was possibility to re-flash bios by inserting usb flash-disk (with .dat file on it, which contained BIOS), and power on PC, while holding some keys combination, then PC was switching to BIOS programming mode and re-flashed BIOS, after that it was possible to boot up normaly. Is there a way to recover computer without hardware programming BIOS chip? p.s. sorry for my english.

  Read the article

< Previous Page | 581 582 583 584 585 586 587 588 589 590 591 592  | Next Page >