Search Results

Search found 2066 results on 83 pages for 'cable'.

Page 63/83 | < Previous Page | 59 60 61 62 63 64 65 66 67 68 69 70  | Next Page >

  • recent unreliable wireless connection with Netgear KWGR614 router

    - by gabkdlly
    Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I know that this router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. Is it possible that someone is jamming my signal ?

    Read the article

  • Wired connection problem through router

    - by tommypincha
    I'm having trouble to connect my Ubuntu 11.10 to internet through ethernet. I installed a router to get Wi-Fi and now (by a wired connection) I can't have internet with ubuntu (but I can with Windows 7). I see several attempts per minute of the network-manager to get a connection, but after a minute it stops trying. Here are a couple of outputs from key files: cat /etc/network/interfaces auto lo iface lo inet loopback and ifconfig -a eth0 Link encap:Ethernet HWaddr 00:16:76:e4:a6:e8 inet6 addr: fe80::216:76ff:fee4:a6e8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:117 dropped:0 overruns:0 frame:117 TX packets:50 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:12221 (12.2 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:582 errors:0 dropped:0 overruns:0 frame:0 TX packets:582 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:46024 (46.0 KB) TX bytes:46024 (46.0 KB) I tried reconnecting the modem and the router and reconnecting the ethernet cable but nothing... I tried other solutions from other posts (this one has a similar issue Wired connection not working) but again nothing. My IP is dynamic. A couple of things I see and did: I see no inet addr, only inet6. I ignored ipv6 from the internet connections, and restarted the network-manager service and nothing. A difference with the post I mentioned is the RX packets with errors I have, is this a clue of the problem? Any help would be appreciated, Thanks!

    Read the article

  • External monitor problems with Asus UX32VD in 12.04

    - by rsilva
    I've posted this video where I show one of the problems I'm facing with my UX32VD in regard of external monitors. As you can see as soon as I plugged the external monitor the laptop screen goes black and the external monitor displays a single color (color changes between red, green and blue). However this does not always happen. For instance if I reboot the laptop with the external monitor already plugged in I get to use it but not the laptop screen. In the Displays settings the laptop screen it's not even listed. Other times it just works. The to screens, without any problems. I tried with other to different external monitor and all this apparently random issues repeat, I even tried using HDMI cable instead. Same random behavior. This question seams to cover one of this issues however the answer did not helped me. I was forced to use the 3.5.2 kernel in order to use the Intel graphics card else the Gallium something was used. Also I've Bumblebee installed.

    Read the article

  • Cannot use second display with 12.04 and Intel 2000/3000

    - by Carolyn Marenger
    I am unable to get anything to display on my second monitor, or even get the system to recognize that there is a second screen. I am running Ubuntu 12.04 on a Gigabyte GA-H61M-S2PV, revision 2.0 box. The integrated chipset is an Intel 2000/3000, and there are both a D-Dub and a DVI-D display ports on the MB. This is the first operating system I have installed on this system. I have a second monitor plugged into the DVI-D port via a DVI-D to D-Sub adapter. I cannot verify that the motherboard or adapter were/are working, short of installing windows to test the theory. When I go into the "System Settings - Displays" control window, it shows one display. I have rebooted with the second monitor attached, and I have perused the BIOS settings in case it might have been disabled. So far, I have had no indication that the second monitor is recognized, not even a flicker at power on. If I swap monitors and cables between the DVI-D and D-Dub ports, the other monitor lights up, so I know the monitor and video cable are not the issue. Any suggestions would be appreciated. Thanks, Carolyn

    Read the article

  • Internet Timeouts with TP-Link TL-WN821N v2 wireless usb stick

    - by user1622959
    A short time after accessing the internet, the browser/download times out. Before the timeout, the internet works OK briefly; afterwards, the wireless is still connected with a strong signal, but every internet access results in a timeout. When I leave the PC for a while, the internet is back just to timeout again as soon as I start using it. The same happens when I reconnect to the router. Also, when I surf the internet, it takes a couple of minutes until the timeout, but when I download something, it times out in a matter of seconds. The wireless adapter works just fine in Windows and internet via ethernet cable works just fine in Ubuntu. Does anyone have the same problem or knows a solution. I use Ubuntu 12.10 x64. The problem occurs since I installed ubuntu (which was a few days ago). Here some stuff that might be usefull: serus@serus-Ubuntu-PC:~$ lsusb Bus 002 Device 002: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 802.11n [Atheros AR9170] serus@serus-Ubuntu-PC:~$ lsmod Module Size Used by carl9170 82083 0 serus@serus-Ubuntu-PC:~$ modinfo carl9170 filename: /lib/modules/3.5.0-21- generic/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko alias: arusb_lnx alias: ar9170usb firmware: carl9170-1.fw description: Atheros AR9170 802.11n USB wireless serus@serus-Ubuntu-PC:~$ iwconfig wlan0 IEEE 802.11bgn ESSID:"virginmedia0137463" Mode:Managed Frequency:2.462 GHz Access Point: A0:21:B7:F8:29:B6 Bit Rate=240 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=66/70 Signal level=-44 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:1399 Invalid misc:18 Missed beacon:0 serus@serus-Ubuntu-PC:~$ sudo lshw -C network *-network description: Wireless interface physical id: 1 bus info: usb@2:2 logical name: wlan0 serial: 00:27:19:bb:00:19 capabilities: ethernet physical wireless configuration: broadcast=yes driver=carl9170 driverversion=3.5.0-21-generic firmware=1.9.4 ip=192.168.0.6 link=yes multicast=yes wireless=IEEE 802.11bgn

    Read the article

  • Why would video stutter on HDMI but not on DVI?

    - by CorvT
    I've got a system running Ubuntu 12.04 with an i3 2120T CPU/GPU. When I play video through mplayer, I notice when I'm hooked up to a screen via HDMI there is a small stutter (1-2 frames) every few seconds. I don't see this happening when I connect via DVI on the same screen. Resolution and refresh rate are same for both HDMI and DVI, so I'm not sure where else the problem could be coming from. I've also tried two different screens, and different cables. I see the stutter with either HDMI-HDMI cables, or DVI-HDMI cable with DVI from the PC and HDMI into the screen. I don't see the stutter with DVI-DVI cables, or when I use HDMI-DVI cables with HDMI from the PC to DVI into the screen. I've also tried using an AMD 5XXX series card with the open source radeon driver, and saw the same problem. I then tried an nVidia GeForce 210 card with the closed source driver, and the stutter went away. To me this smells like a driver/mesa/glx issue (since the problem went away with the nvidia card/driver), but I have no idea how to track this down.

    Read the article

  • Wirelessly Sync Photos From iPhone To Computer Using CameraSync

    - by Gopinath
    How do you upload photos captured on your iOS device to your computer? By connecting the device using a cable and then syncing up with an app?? Ah..is’nt it a boring way. Here comes CameraSync – an app that lets you wirelessly send your iOS device photos to DropBox, so that you can access on your computer irrespective of the platform (Windows, Mac, Linux). By the way, this app works in the background and syncs the  files without disturbing  you. You don’t like DropBox? CameraSync works with a variety  of cloud services : Flickr, Amazon S3, iDisk, FTP and Box.net. If you looking for a step by step guide on how to setup CameraSync for DropBox then check this post. CameraSync cost $1.99 and runs on iOS4.0+ devices. CameraSync [iTunes App via Lifehacker] This article titled,Wirelessly Sync Photos From iPhone To Computer Using CameraSync, was originally published at Tech Dreams. Grab our rss feed or fan us on Facebook to get updates from us.

    Read the article

  • Wrong resolution for Lightdm/GDM on Ubuntu 13.04 using HDMI

    - by f03lipe
    I've tried all the solution I could find on the matter so far, but the error persists. My problem is that the login screen (both under gdm and lightdm) runs with the wrong resolution, even though all is fine when I log in. The error occurs solely when I have my HDMI cable connected to my other screen. The login screen resolution becomes 1024x768 (for my 1366x768 laptop screen) and mirrored on my screen, which is 1920x1080. I've had this issue on version 12.04 (the last one before I upgraded to 13.04), but I got it fixed by adding the xrandr commands on the begining of the /etc/gdm/Init/Default file. This doesn't seem to work anymore. I've also tried telling lightdm to run a script fixing the resolution with xrandr (by editing /etc/lightdm/lightdm.conf), but lightdm crashes, and I'm forced to log in with low graphic settigs. Hint: when ubuntu is loading, the resolution starts OK, then goes bad right before the login screen is initialized. Does that mean that there's nothing wrong with my graphic cards? What do you think? Cheers!

    Read the article

  • recent unreliable wireless connection

    - by gabkdlly
    Recently, my internet connection over wireless ( via a Netgear KWGR614 router ) has become unreliable, on both a Dell laptop running Ubuntu 10.04 as well as my Desktop running Ubuntu 10.10 . The problem does not seem to occur on a laptop running Windows Vista, nor on a Desktop running Windows 7 ( this machine is connected with an ethernet cable ). The problem does not seem to occur on my Openmoko Freerunner ( running Android 1.5 ), though I hardly ever use this device to connect over WLAN, so the problem may have just slipped by. On my main Ubuntu Desktop, I have tried the following wireless devices: a Longshine PCI card ( an old device with an RTL8180L chip ) a D-Link DWL-510 PCI card ( this device threw warnings in dmesg ) a USB device from MSI ( US54EX ). Usually my wireless network shows up in the network manager with a normal signal strength, even when the connection speed is slow or the connection gets reset ( asking me to click connect to re-authenticate my wireless connection ). I have observed this problem with a Netgear KWGR614 Router ( with the manufacturers firmware ), as well as with a TP-LINK TL-WR741ND router running OpenWrt. Taking a look at my routers logs, I find many instances of the following line: Tuesday,04 Jan 2011 03:53:01 [TCP SYN Flood][Deny access policy matched, dropping packet] I know that the Netgear router is susceptible to denial of service attacks, as I have previously been able to disrupt its operation by putting an nmap scan into a while loop. I use WEP or WPA to encrypt the wireless network. Is it possible that someone is jamming my signal ?

    Read the article

  • 1080p Screen resolution problem after 10.04 to 12.04 update

    - by Ale
    I have a Samsung LCD 40" with a NVidia GeForce 6150SE nForce 430 Card. I recently upgraded from 10.04 to 12.04 and the best resolution I can get is 1360x768. I've tried the propietary drivers available on the repository kmod:nvidia_current kmod:nvidia_173_updates kmod:nvidia_current_updates kmod:nvidia_96 kmod:nvidia_96_updates kmod:nvidia_173 I've also downloaded latest from NVidia's Web, version: 295.40. But still no luck. With Nouveau driver, I can only get 1024x768. I know there is no problem with my hardware (video card, cable and monitor), I was using it perfectly on 10.04. Can anybody suggest something else I could try, to get my 1920x1080 resolution back? Thanks in advance. Here are some more information, that I got reading other similar posts on askubuntu. $ lspci | grep VGA 00:0d.0 VGA compatible controller: NVIDIA Corporation C61 [GeForce 6150SE nForce 430] (rev a2) $ xrandr xrandr: Failed to get size of gamma for output default Screen 0: minimum 320 x 240, current 1360 x 768, maximum 1360 x 768 default connected 1360x768 0 0 0mm x 0mm 1360x768 50.0 52.0* 1024x768 51.0 800x600 53.0 54.0 55.0 680x384 56.0 57.0 640x480 58.0 576x432 59.0 512x384 60.0 400x300 61.0 62.0 63.0 320x240 64.0

    Read the article

  • Wired connection to windows ISC stopped working

    - by cmpickle
    I have had my Linux box connected to the internet through a Windows computer by wiring them together with a cat5 cable then the Windows is connected wireless to a router. This setup has worked since I got the Linux box but just yesterday stopped working. The changes that occurred were: I changed networking so that I was connecting the Linux box and Windows computer through a second router so during that time the Linux box went through a router to connect to the Windows computer that was still connected wireless to the first router. The Internet didn't work on the Linux box at the time they second router was involved when I removed it and directly connected the Linux box and Windows the Internet worked again. Another thing that changed was that I had disconnected my Windows computer from all network connections and deleted them to make my Ethernet work better. Also at that time my dad had I connect the Windows to a third router and changed some settings in it. After reconnecting this time the connection between the router and the windows would not establish. If anyone has any ideas as to why this is I would greatly appreciate it!

    Read the article

  • 12.10 Wireless networking

    - by user108594
    I downloaded ubuntu 12.10 using WUBI and cannot connect to the internet. I removed it and downloaded ubuntu 12.04 still cannot connect. This I assume rules out the program being the problem. I reinstalled 12.10. When loaded I get the same message W/red (x) stating Internet not connected. I went to the Settings drop down box and it does not reveal the network list but (enable networking has a ck mark). Am running a HP Laptop with a w/7/64 OS that has a kill switch that indicates (orangeno connection) I downloaded 12.10 on my desktop (on the same network) and everything OK. I tried to follow the instructions in the help menu but got lost and confused . Sincerely Dan Additional Info per request Broadcom 802.11b/g Wlan Internal pc [hp laptop] P.S. I've been out of town for about a month. TKS for your gitback I did install 12.10 via cd and everything ok,but retried alongside 7 and unable to connect to internet,also took laptop and hard wired using ethernet cable and everything ok. stumped again and running out of ideas!!!

    Read the article

  • How to represent a graph with multiple edges allowed between nodes and edges that can selectively disappear

    - by Pops
    I'm trying to figure out what sort of data structure to use for modeling some hypothetical, idealized network usage. In my scenario, a number of users who are hostile to each other are all trying to form networks of computers where all potential connections are known. The computers that one user needs to connect may not be the same as the ones another user needs to connect, though; user 1 might need to connect computers A, B and D while user 2 might need to connect computers B, C and E. Image generated with the help of NCTM Graph Creator I think the core of this is going to be an undirected cyclic graph, with nodes representing computers and edges representing Ethernet cables. However, due to the nature of the scenario, there are a few uncommon features that rule out adjacency lists and adjacency matrices (at least, without non-trivial modifications): edges can become restricted-use; that is, if one user acquires a given network connection, no other user may use that connection in the example, the green user cannot possibly connect to computer A, but the red user has connected B to E despite not having a direct link between them in some cases, a given pair of nodes will be connected by more than one edge in the example, there are two independent cables running from D to E, so the green and blue users were both able to connect those machines directly; however, red can no longer make such a connection if two computers are connected by more than one cable, each user may own no more than one of those cables I'll need to do several operations on this graph, such as: determining whether any particular pair of computers is connected for a given user identifying the optimal path for a given user to connect target computers identifying the highest-latency computer connection for a given user (i.e. longest path without branching) My first thought was to simply create a collection of all of the edges, but that's terrible for searching. The best thing I can think to do now is to modify an adjacency list so that each item in the list contains not only the edge length but also its cost and current owner. Is this a sensible approach? Assuming space is not a concern, would it be reasonable to create multiple copies of the graph (one for each user) rather than a single graph?

    Read the article

  • external hard drive not detected after ubuntu crash [restarting machine]

    - by Netmoon
    today i tried to watch movie [with vlc media player] from my external hard drive [expansion portable 500 GB], and it's play good, then pause the movie and play it again, and my Ubuntu crashed! [Ubuntu 12.04]i had to restart the machine, so did it, but after that Ubuntu can't recognize this hard drive! i changed USB cable but it was not effective. this is my dmesg command result : [ 191.281630] usb 2-1.3: new full-speed USB device number 9 using ehci_hcd [ 191.353527] usb 2-1.3: device descriptor read/64, error -32 [ 191.529115] usb 2-1.3: device descriptor read/64, error -32 [ 191.704669] usb 2-1.3: new full-speed USB device number 10 using ehci_hcd [ 191.776524] usb 2-1.3: device descriptor read/64, error -32 [ 191.952202] usb 2-1.3: device descriptor read/64, error -32 [ 192.127772] usb 2-1.3: new full-speed USB device number 11 using ehci_hcd [ 192.534742] usb 2-1.3: device not accepting address 11, error -32 [ 192.606749] usb 2-1.3: new full-speed USB device number 12 using ehci_hcd [ 193.013696] usb 2-1.3: device not accepting address 12, error -32 [ 193.013906] hub 2-1:1.0: unable to enumerate USB device on port 3 note: I am able to hear the sound of the external drive lens. When attach hard drive to usb port, the status light goes on, but it's low bright and i think its power is low! try to mount in Microsoft Windows 7, but nothing happened.

    Read the article

  • Cannot connect to wireless network

    - by smr
    I am quite new to using Ubuntu 12.10. All I remember while installing Ubuntu 12.10 was that I didn't check any box specifically to enable wireless connectivity. I tried looking into the various questions posted here - most of them refer to certain commands (redundantly sudo) and things of that sort. I am quite new and wasn't sure of understanding what those commands were trying to do (the network configuration settings - showed up different options, like 'Wireless', 'Wired', 'IPv4', 'IPv6' etc -- I am not sure of what sort of settings are to be made - like for example what sort of 'WEP' settings etc are to be made. Although I wasn't able to connect to the wireless network, I was able to connect to the internet, once I plugged in the ethernet cable. Can someone help me with: 1) Understandng a way to see if Ubuntu is configured to connect to a wireless network. 2) If so - Getting to configure to a wireless network (setting up a new one). 3) Where in ubuntu, should I look for seeing if there are any hardware devices (such as the Broadcom wireless adapter or things of that sort - like the way we use the 'Device manager' in Windows to look into the adapter settings). 4) Reference material to learn and understand the various ubuntu commands. (things like the -lshw etc).

    Read the article

  • Driver for asus wireless PC card WL-100GE

    - by emab
    I have bought an Asus wireless LAN PC Card WL-100GE model, and I am using lubuntu on my system. While I have no cable connection, currently I cannot access the internet and update my laptop. Device: Broad Range Wireless Card Bus Adaptor - Asus - WL-100GE I searched the web and couldn't find any adequate driver for it. Is there any solution for it? My sudo lshw -C network output is: *-network description: Ethernet interface product: RTL-8100/8101L/8139 PCI Fast Ethernet Adapter vendor: Realtek Semiconductor Co., Ltd. physical id: 3 bus info: pci@0000:02:03.0 logical name: eth0 version: 10 serial: 00:02:3f:ba:55:c8 size: 10Mbit/s capacity: 100Mbit/s width: 32 bits clock: 33MHz capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=8139too driverversion=0.9.28 duplex=half latency=128 link=no maxlatency=64 mingnt=32 multicast=yes port=MII speed=10Mbit/s resources: irq:19 ioport:3000(size=256) memory:e0200800-e02008ff *-network description: Network controller product: BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller vendor: Broadcom Corporation physical id: 1 bus info: pci@0000:07:00.0 version: 02 width: 32 bits clock: 33MHz capabilities: bus_master configuration: driver=b43-pci-bridge latency=64 resources: irq:21 memory:38000000-38001fff ----:~$ iwconfig lo no wireless extensions. eth0 no wireless extensions.

    Read the article

  • Wired card not connecting after trying to connect

    - by Mike
    I have an Ubuntu 12.10 PC. When I plug in my internet cable it starts connecting and after a minute it says it can't connect. I tried different cables but nothing works. Wlan works. I think it's the network driver but I don't know how to install/update it. Here's the ifconfig info (if it helps): eth0 Link encap:Ethernet HWaddr 00:01:6c:39:2a:8d inet6 addr: fe80::201:6cff:fe39:2a8d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2011 errors:0 dropped:362 overruns:0 frame:0 TX packets:586 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:175452 (175.4 KB) TX bytes:147211 (147.2 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:9779 errors:0 dropped:0 overruns:0 frame:0 TX packets:9779 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8460080 (8.4 MB) TX bytes:8460080 (8.4 MB) wlan0 Link encap:Ethernet HWaddr 08:10:74:35:99:9d inet6 addr: fe80::a10:74ff:fe35:999d/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:1790 errors:0 dropped:0 overruns:0 frame:0 TX packets:3250 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:401664 (401.6 KB) TX bytes:2898773 (2.8 MB)

    Read the article

  • issues with ASUS S301L ultrabooks

    - by Wuerze
    I just like to tell you what still is a Problem in Ubuntu 14.04 and should be solved for a nice experience of this distribution. Unfortunately I do not have any hints to tell you, because I am just a user and know not much about programming. Anyway, I hope it helps. 1) Intel open source Graphics issues (proprietary) -when attaching HDMI-cable the screen switches to the external monitor and it's fine, but there is no switching back unless restart with HDMI deattached -black screen appears for like 2 seconds as if I would change screen in the settings; frequency increases with intensity of driver use (i.e. videos or video games) 2) hotkeys (commonly recognised) -there is no possibility to adjust brightness with the hotkeys (Fn+F5 and Fn+F6) 3) touchscreen (commonly recognised) -the touchscreen is behaving like a mouse -configuring gestures for the multi touch screen seems to always end in disabling touch pad gestures 4) panel symbols -battery symbol has got a low accuracy while it determines accurately the energy left; only 5 steps of energy are shown by the symbol Thank you all for participating in the solution of these problems! I will stay tuned and edit this list if something has been solved.

    Read the article

  • Kubuntu not showing eth0

    - by Laurbert515
    I just installed Kubuntu 12.04.2 and do not have an internet connection. I also cannot access the Desktop and only have the terminal. When I enter xlcock I get Error: Can't open display:. I believe this is because I do not have the correct drivers and need to download them ... using the internet which I can't access. So here's what's going on ... ifconfig gives: lo Link ecap: Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:16 errors:0 dropped:0 overrruns:0 frame:0 TX packets:16 errors:0 dropped:0 overrruns:0 frame:0 collisions:0 txqueuelen:0 RX bytes:1296 (1.2 KB) TX bytes:1296 (1.2 KB) wlan0 Link encap: Ethernet HWaddr 68:17:29:58:49:4a UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:16 errors:0 dropped:0 overrruns:0 frame:0 TX packets:16 errors:0 dropped:0 overrruns:0 frame:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lspci -nnk gives: 07:00.0 Network Controller [0280] Intel Corporation Centrino Wireless-N 2230 [8086:0887] (rev c4) Subsystem: Intel Coporation Centrino Wireless-N 2230 BGN [8086:4062] Kernel driver in use: iwlwifi Kernel modules: iwlwifi 0d:00.0 Ethernet Controller [0200]: Atheros Communications Inc. AR8161 Gigabit Ethernet [1969:1091] (rev 10) Subsystem: Toshiba America Info Systems Device [1179:fa77] I believe this means that it is using the ethernet connection but thinks it is a wireless connection. sudo lshw -class network gives: *-network description: Wireless interface product: Centrino Wireless=N 2230 ... *network UNCLAIMED description: Ethernet controller product: AR8161 Gigabit Ethernet I want to get the internet working so I can fix the GPU driver, etc. but I can't seem to get it working even though I have my ethernet cable plugged in (and I'm sure it is working).

    Read the article

  • External monitor on old Dell 700m?

    - by Adam Henne
    Okay, linux noob. I installed 10.04 on an old Dell 700m in hopes of using it as a media center device. That seems to work great, except now it won't output to the external monitor. VGA cable works fine, TV recognizes other computers fine, it's the laptop that won't output. Turns out that the 700m, unlike every other computer out there, doesn't have a Fn hotkey to switch monitors. The only way to do it in Windows was to go through the Control Panel. In Ubuntu, though, the Monitor setup won't detect or recognize any monitors. The laptop display works fine, but I can't adjust or add anything. I did a little research and found suggestions for older Ubuntu builds involving the xorg.conf. I tried one out, in spite of my unfamiliarity, and it's screwed the whole display big time. I can fix that with a clean reinstall, that's no problem, but I'm cautious about editing xorg again. Any suggestions? Thank you!

    Read the article

  • Automatic switching between monitor configurations

    - by Michael Aquilina
    I have a laptop and an external monitor and i was wondering if there was a simple approach to switching between multiple monitor configurations based on the detected available displays. For example: When i am at home and i plug in my external monitor i would like this to automatically become enabled and the laptop screen to become disabled. As soon as i pull out the display cable for the external monitor, i would like the laptop screen to automatically become enabled. I was expecting this to just "work" just like it does in windows - but it seems to be much harder than that. I am aware of the xrandr command to turn displays on and off but i cannot seem to find a way to get this to work the way i describe above. I had also found this post about switching between multiple monitor configurations and the results seem a bit inconclusive. However i was hoping that with xrandr there would be a simpler solution. For me, the fact that when i pull out my external monitor the screen just goes black and i get an error message is a big issue holding me back from making the complete switch to linux as i move around alot as a student. My OS of choice is currently Kubuntu 12.04 but i am willing to change to something else if it provides a better way of setting up the described setup.

    Read the article

  • WIFI/LAN not working after Installing Ubuntu 13.10

    - by user183025
    I can't connect to my WIFI after installing Ubuntu 13.10. I tried re-installing it three times (thinking that I did something wrong during the installation) but I still can't connect to my WIFI. It just gives me the message that I'm offline and that I can't connect to my WIFI. I also tried connecting to the internet using LAN cable but with the same results. I tried google but it seems that there's no solution to this yet.... Anybody knows how to solve this? Thanks! FYI: H/W path Device Class Description ====================================================== system RC530/RC730 (To be filled by O.E.M.) /0 bus RC530/RC730 /0/0 memory 64KiB BIOS /0/4 processor Intel(R) Core(TM) i5-2410M CPU @ 2.30GHz /0/4/5 memory 32KiB L1 cache /0/41 memory 4GiB System Memory /0/41/0 memory DIMM [empty] /0/41/1 memory 4GiB SODIMM DDR3 Synchronous 1333 MHz (0.8 ns) /0/100 bridge 2nd Generation Core Processor Family DRAM Controller 02:00.0 Network controller: Intel Corporation Centrino Wireless-N 130 (rev 34) Subsystem: Intel Corporation Centrino Wireless-N 130 BGN Flags: bus master, fast devsel, latency 0, IRQ 44 Memory at f7200000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi 03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 06) Subsystem: Samsung Electronics Co Ltd Device c0c1 Flags: bus master, fast devsel, latency 0, IRQ 41 I/O ports at b000 [size=256] Memory at f2104000 (64-bit, prefetchable) [size=4K] Memory at f2100000 (64-bit, prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: r8169 Kernel modules: r8169

    Read the article

  • Wired connection not working

    - by YokoBlac
    I am using a Acer Aspire One. Here is the Ubuntu Wiki Page about my computer. I have a working wireless connection however when I plug a cat5 (Ethernet) cable in the lights flicker on the computer, but then nothing happens. Output of iconfig: eth0 Link encap:Ethernet HWaddr 00:1e:68:96:1a:6b inet6 addr: fe80::21e:68ff:fe96:1a6b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:43 errors:0 dropped:0 overruns:0 frame:0 TX packets:12 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2622 (2.6 KB) TX bytes:936 (936.0 B) Interrupt:28 Base address:0xe000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) wlan0 Link encap:Ethernet HWaddr 00:22:68:92:7f:36 inet addr:192.168.1.6 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::222:68ff:fe92:7f36/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5702 errors:0 dropped:0 overruns:0 frame:0 TX packets:5284 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4117327 (4.1 MB) TX bytes:936709 (936.7 KB) Any understanding of this output is greatly appreciated.

    Read the article

  • Accidentally Changed Dual Monitor Setup and don't know how to reset it

    - by user203783
    I have a dual monitor setup with my laptop and an external Asus monitor running under Ubuntu 11.10. When I first started using Ubuntu, it synced both screens. What showed up on my laptop showed up on my eternal monitor. Last night, I accidentally knocked the HDMI cable from its port (not that unusual in the tight space I work in). When I plugged it back in, as usual, the external monitor only displayed my wallpaper. Usually, I just restart Ubuntu and it resets, but last night what I now realize was the display console came up and somehow I changed the setup. Now the two screens show different jobs so to speak. Also, the external monitor doesn't display the ribbon, making switching between Firefox tabs and windows or apps jarring. I write for a living and need to quickly check bits of research, notes or sources while writing and the extra switching between mouse pad and external mouse to get one or the other screen to respond interrupts my work flow. The only technical help I can offer is when the display console popped up, the graphical representation of the screens was that the external screen appeared layered over by about one-quarter of the laptop screen. Again, these were icons. I tried to replicate that after I obviously screwed things up. If someone could help. I would appreciate it. If I have to use terminal, that's fine. I started using computers for writing back when they were green DOS prompts. There's a certain elegance to prompt commands to me. Maybe it's the writer in me. Again, if anyone can help me return my screens to sync under Ubuntu 11.10, I would greatly appreciate it.

    Read the article

  • How do I force the system to look for new sound devices?

    - by John Zeringue
    I have a small flat screen TV (Toshiba) that I often connect via HDMI to my laptop (an HP Pavilion dv4) and use as a computer monitor. When I do this, I prefer to use the TV's speakers, particularly when I'm watching video, because the sound quality is much better. However, when I connect the HDMI cable after turning on my computer (rather than having it plugged in before booting up), Sound Settings does not list the TV as an output device, and I am forced to reboot. I was curious if there is an easier solution to this, perhaps a CLI command to check for new sound outputs. Does anyone know of something like this or have another solution? To clarify, I believe this is a software problem. The HDMI always works, and I can switch my desktop over to the TV at any time. The issue is that, if the HDMI wasn't connected during start up, the TV will not appear as an output option in the Sound Settings GUI. So, unless I'm mistaken, my question is not HDMI specific, but rather a general usage question about manipulating sound settings from the command line.

    Read the article

< Previous Page | 59 60 61 62 63 64 65 66 67 68 69 70  | Next Page >