Search Results

Search found 2130 results on 86 pages for 'swap'.

Page 63/86 | < Previous Page | 59 60 61 62 63 64 65 66 67 68 69 70  | Next Page >

  • External 1TB WD USB 3.0 HDD is not detecting. Working perfectly find in Windows

    - by Yathi
    My 1TB USB 3.0 was working fine earlier in Ubuntu as well as Windows. But lately it is not at all being detected in Ubuntu. It still works fine in Windows. I did update my Ubuntu to 12.10 but I am not sure if that caused the issue. When I connect my HDD and run dmesg | tail: [ 47.804676] usb 4-3: >Device not responding to set address. [ 48.008575] usb 4-3: >Device not responding to set address. [ 48.212421] usb 4-3: >device not accepting address 9, error -71 [ 48.324451] usb 4-3: >Device not responding to set address. [ 48.528340] usb 4-3: >Device not responding to set address. [ 48.732165] usb 4-3: >device not accepting address 10, error -71 [ 48.844138] usb 4-3: >Device not responding to set address. [ 49.048179] usb 4-3: >Device not responding to set address. [ 49.251881] usb 4-3: >device not accepting address 11, error -71 [ 49.251907] hub 4-0:1.0: >unable to enumerate USB device on port 3 The output of sudo fdisk -l is : Disk /dev/sda: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders, total 1953525168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x00030cde Device Boot Start End Blocks Id System /dev/sda1 2048 1332981759 666489856 83 Linux /dev/sda2 1332981760 1953523711 310270976 5 Extended /dev/sda5 1332983808 1349365759 8190976 82 Linux swap / Solaris /dev/sda6 1349367808 1953523711 302077952 7 HPFS/NTFS/exFAT Disk /dev/sdb: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 14593 cylinders, total 234441648 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000a2519 Device Boot Start End Blocks Id System /dev/sdb1 * 2048 103368703 51683328 7 HPFS/NTFS/exFAT /dev/sdb2 103368704 154568703 25600000 83 Linux /dev/sdb3 154568704 234440703 39936000 7 HPFS/NTFS/exFAT /dev/sda and /dev/sdb are my 2 internal HDDs. But the external one which should be /dev/sdc is not even being shown though it is connected and the LED on the HDD is glowing. Someone had suggested adding blacklist uas to /etc/modprobe.d/blacklist.conf. Tried that as well. But still not working. Can someone help me out.

    Read the article

  • Rebuilding array on 3ware 9690SA-8I

    - by Tim Jones
    I have a RAID10 (8x1TB) array on a 3ware 9690 card running on an Ubuntu 1110 server. There was a kernel update so I scheduled a reboot after which the array was inaccessible. I checked the status a drive has died in the array, but the controller has thrown the entire array into an 'inoperable' state instead of simply degraded (what's the point of the RAID now ;-). After taking out the 'dead' drive I run a quick test to find it completely functional without a bad sector to be found. I try to put the drive back in but the array still marks the disk as degraded (remembering serial number or something??) and the entire array as inoperable... So I swap it out for a known working drive (not the same capacity but higher - should still work) and initiate a rebuild with the the new drive as a replacement. This fails instantly with the error "(0x0B:0x0033): Unit busy : Failed to start Rebuild on Unit 0". The unit shouldn't be busy as it is not mounted (the card itself is listed with lshw but the array it provides is not). I'm pretty much at an impasse now, I don't understand how I can have a single drive failure on a RAID10 that makes the entire array inaccessible, degraded I could understand but inaccessible?? I don't think the controller as prior to the reboot it was completely functional.

    Read the article

  • VMWare ESXi, change the default path for a VM

    - by glenatron
    For some reason VMWare ESXi has decided that one of my VMs is on a completely different path to the path it is actually on. So my VM is on /vmfs/volumes/long-guid-here/my-vm-name but when I try to open it I get the message "File < unspecified filename was not found." Which is not really surprising as unspecified filenames are quite difficult to locate. I thought it was just the swap file, which was down in the .vmx file as /vmfs/volumes/long-guid-here/old-vm-name/old-vm-name.vmsd but when I changed that in the vmx it made no difference. What I can't figure out is where VMWare is getting the old-vm-name from- when I look in the "Settings" pane it believes the working file location to be "[datastore-name] old-vm-name\" and I can't find anywhere to change it. Now the files themselves are all named for old-vm-name - so the directory is /my-vm-name/old-vm-name.vmx and so on. Is this the cause of my problems or is there some arcane configuration option elsewhere around the VMWare machine that I need to be tinkering with?

    Read the article

  • How to safely remove a USB device from 2008 Core server?

    - by Qwerty
    I have a Hyper-V Core server 2008 that I administer via command line and remote tools. We have now got a new backup system in place and it involves me connecting an External USB drive (G:) to backup system state files. My question is how should I safely remove the drive for its weekly offsite swap? I've tried using the devcon tool however it just says the 'removal failed with no devices removed' with no other explanation. I have noticed that there isnt a readily available x64 version of devcon and that might be the cause of the problem. (I have read of people downloading a amd64 version but I have not located it myself, if someone knows where it is please let me know). The devcon command worked on my old 2003 x86 server with the command: devcon remove *3200AVJ_EXTERNAL* I have also looked at using fsutil volume dismount g: but it doesn't seem to work as G: is still listed as a connected volume. I have checked that the volume is not in use via remote tools and the net file command. Both show no open files in the G:\ volume. This could be a decent substitute as it might be used to flush any remaining IO to the volume can anyone clarify? Thanks in advance.

    Read the article

  • blu-ray archiving in vmware ESXi 4

    - by spacecadet77
    Hi, I need some advice about using blu-ray writer for archiving data on vmware ESXi 4. At office we have IBM System x3400 Tower server with ESXi 4 hipervisor and OpenSuse and CentOS GNU/Linux system as guests. Will blu-ray writer work in this setup, and if it will is there any particular model you can suggest. Best regards IBM System x3400 Tower server specification: 1x Intel Quad-Core Xeon E5410 2.33GHz/ 12MB/ 1333MHz (2x CPU max) Intel 5000P chipset, 2x 1GB PC2-5300 DDR2 667MHz SDRAM ECC Chipkill (32GB max) 2x4GB (2x2GB) PC2-5300 CL5 ECC DDR2 FBDIMM (x3400, x3550, x3650) SAS/SATA Hot-Swap Open Bay (0xHDD std, 4xHDD max, 8xHDD optional) ServeRAID 8K dual channel SAS/SATA controller (RAID 0,1,1E,10,5,6, 256MB, Battery Backup) Graphics ATI® RN50(ES1000) 16MB DDR, CD-RW/DVD Combo no FDD GigaEthernet, Tower with Power Supply 835W (opt Redudant) Slot 1: half-length, PCI-Express x8(x4 electrical) Slot 2: full, PCI-Express x8 Slot 3: full, PCI-Express x8 Slot 4: full, 64-bit 133MHz 3.3v PCI-X Slot 5: full, 64-bit 133MHz 3.3v PCI-X , Slot 6: half-length, 32-bit 33MHz 5.0v PCI ports: 4x USB (Vers 2.0), 2x PS/2, parallel, 2x serial (9-pin), VGA, RJ-45 (ethernet ), RJ-45 (sys mgm) HDD 4 x TB 7200rpm / Serial ATA II 3.0Gb/s / 16MB, RoHS

    Read the article

  • Ideal Bacula appliance?

    - by Ricket
    I'm an intern at a small company and we (the IT department of two) manage <100 client computers and a handful of servers. Currently we're using a company's appliance to handle backup; it does a small backup every night and a full backup every weekend, and a guy comes on Wednesday to take an offsite backup drive (and gives back last week's drive to swap with it). Lately this system, mainly the appliance, has been having problems, so we are looking for an alternative. I'm researching other companies but also looking into what we might expect from trying to do this ourselves. There will undoubtedly be a large learning curve, but hey, that's what serverfault is for, right? :) So anyway I was looking at Bacula. Feature list sounds great, documentation is plentiful, but it's only software. So my question is, what is the ideal backup server to run the Bacula server software on? And not only the server but other related appliances. Our current backup appliance uses only hard drives, not tape drives. It has several plugged into it at one time, in hotswap bays on the front of the machine. I couldn't help but notice though, it's hardly more than Windows XP with hard drive bays, a PCI eSATA card (which connects to another appliance extension piece with 2 more bays), and their software. Since the company will take back their appliance if/when we cancel with them, where can I go to configure a server with these kinds of things? Maybe I'm being naive, I'm sure Dell (and any other computer company) sells them in the small business section of their website, but I wanted to make sure that there's not some other more recommended place that other companies are getting their hardware from, and that I don't need anything special for Bacula.

    Read the article

  • PHP CLI not respecting memory limit in php.ini

    - by user13743
    I am using drush, which is a command-line php app to manage a drupal website. I am running a command to import a lot of data, which is causing me to hit php's memory limit. PHP Fatal error: Allowed memory size of 536870912 bytes exhausted ... Which is 512MB if I'm doing the math correctly (536870912 / 1024 / 1024 = 512). I've changed the directive in the php.ini that drush uses: $> drush status ... PHP configuration : /etc/php5/cli/php.ini $> grep memory /etc/php5/cli/php.ini ; Maximum amount of memory a script may consume (128MB) ; http://php.net/memory-limit memory_limit = 1024M But I'm still hitting the 512 MB limit! I am running in a virtual machine, whose memory settings I changed from 512 to 1025 MB of RAM to allow drush to run. $> free -m total used free shared buffers cached Mem: 1010 578 431 0 14 392 -/+ buffers/cache: 172 837 Swap: 382 0 382 So it says it has some 431 MB free, now that I've bumped the vm up to 1024. I guess half the memory is being used to run the GUI, but I don't understand how the GUI was running okay when the vm had 512 MB of ram. Why is the PHP cli still hitting a 512 MB memory limit? If it was hitting a system memory limit, shouldn't it die around 431MB, which is what the free command says is available?

    Read the article

  • DVD-ROM: Pioneer DVD-115GA not being detected.

    - by Wesley
    Specs to put things in context: AMD Athlon XP 2400+ @ 2.00 GHz / 2 x 512 MB PC-3200 DDR RAM / 160 GB IDE HDD / 128 MB GeForce 6200 AGP / FIC AM37 / Windows XP Pro SP3 So this computer is actually an upgraded EMachines T2482. I found a used DVD-ROM for cheap... the Pioneer DVD-115GA. I originally had a plain DVD Reader (Lite-On XJ-HD166S) which was quite useless. So I basically did a simple swap of the drive and powered up the computer. The drive could open and close, and I put in a DVD and it was spinning, but no detection. Going into the BIOS, the drive was not detected. (The IDE cable connecting the DVD-ROM is connected to the CD-ROM below it and then attached to the secondary IDE port on the motherboard.) So I started all the way up and tried to scan for hardware changes in Computer Management. Still, nothing. I have the software downloaded from the Pioneer site, and that couldn't detect anything. So what else can I try to hopefully get my DVD-ROM recognized by the BIOS? Thanks in advance!

    Read the article

  • Problem: Munin Graph

    - by Pablo
    I've been trying to install Munin for 15 days, I looked for information, analized logs, I even deleted and reinstalled Munin using YUM. I'm hosted at Media Temple on a VPS with CentOS. The problem is still there and It's driving me nuts. Graphics are shown as following: http://imageshack.us/photo/my-images/833/capturadepantalla201106u.png/ This is the configuration of my munin.conf file dbdir /var/lib/munin htmldir /var/www/munin logdir /var/log/munin rundir /var/run/munin [localhost] address **.**.***.*** #IP VPS This is the configuration of my munin-node.conf file log_level 4 log_file /var/log/munin/munin-node.log port 4949 pid_file /var/run/munin/munin-node.pid background 1 setseid 1 # Which port to bind to; host * user root group root setsid yes # Regexps for files to ignore ignore_file ~$ ignore_file \.bak$ ignore_file %$ ignore_file \.dpkg-(tmp|new|old|dist)$ ignore_file \.rpm(save|new)$ allow ^127\.0\.0\.1$ Thanks so much, I appreciate all the answers UPDATE munin-graph.log Jun 22 16:30:02 - Starting munin-graph Jun 22 16:30:02 - Processing domain: localhost Jun 22 16:30:02 - Graphed service : open_inodes (0.14 sec * 4) Jun 22 16:30:02 - Graphed service : sendmail_mailtraffic (0.10 sec * 4) Jun 22 16:30:02 - Graphed service : apache_processes (0.12 sec * 4) Jun 22 16:30:02 - Graphed service : entropy (0.10 sec * 4) Jun 22 16:30:02 - Graphed service : sendmail_mailstats (0.14 sec * 4) Jun 22 16:30:02 - Graphed service : processes (0.14 sec * 4) Jun 22 16:30:03 - Graphed service : apache_accesses (0.27 sec * 4) Jun 22 16:30:03 - Graphed service : apache_volume (0.15 sec * 4) Jun 22 16:30:03 - Graphed service : df (0.21 sec * 4) Jun 22 16:30:03 - Graphed service : netstat (0.19 sec * 4) Jun 22 16:30:03 - Graphed service : interrupts (0.14 sec * 4) Jun 22 16:30:03 - Graphed service : swap (0.14 sec * 4) Jun 22 16:30:04 - Graphed service : load (0.11 sec * 4) Jun 22 16:30:04 - Graphed service : sendmail_mailqueue (0.13 sec * 4) Jun 22 16:30:04 - Graphed service : cpu (0.21 sec * 4) Jun 22 16:30:04 - Graphed service : df_inode (0.16 sec * 4) Jun 22 16:30:04 - Graphed service : open_files (0.16 sec * 4) Jun 22 16:30:04 - Graphed service : forks (0.13 sec * 4) Jun 22 16:30:05 - Graphed service : memory (0.26 sec * 4) Jun 22 16:30:05 - Graphed service : nfs_client (0.36 sec * 4) Jun 22 16:30:05 - Graphed service : vmstat (0.10 sec * 4) Jun 22 16:30:05 - Processed node: localhost (3.45 sec) Jun 22 16:30:05 - Processed domain: localhost (3.45 sec) Jun 22 16:30:05 - Munin-graph finished (3.46 sec)

    Read the article

  • svchost consuming more than 50% CPU all the time in windows 7

    - by claws
    Hello, I'm using windows 7 ultimate. svchost containing DCOM Server Process Launcher Plug and Play Power services is consuming more than 50% of CPU for most of the time. I found this blog post: http://blog.hansmelis.be/2007/06/17/windows-vista-long-delay-when-switching-songs-in-media-player/ That process is associated with two services: DCOM Server Process Launcher and Plug and Play. For the Vulcans among us, all logic stops there for a second. What do those two services have to do with WMP? The answer is provided by Vista's new audio engine. The new engine supports several audio "enhancements". But for the enhancements to work, the engine needs to determine if your hardware is up to the task. And when does it check that? Each time a sound output device is accessed. That's pretty nice if you can do a hot swap of sound hardware, but I don't see me doing that anytime soon. Anyways, it does provide us with the link to the correct service because checking hardware is done by the "Plug and Play" service. One might think that deactivating each enhancement would solve the problem, but that's wishful thinking. The configuration of the enhancements is located in the properties of the sound hardware. When opening the tab, I found out that no enhancements were active. Hmmm... so why does it check the hardware? Well, it does that in case you actually enable an enhancement. To completely stop the hardware checking, you have to tick the box labelled Disable all enhancements. As soon as you do that, Vista finally understands you don't want to use them buts thats for vista. Is it the same case with windows 7 too? and I couldn't find any "Disable all enhancements" in my controlpanelsounds (mmsys.cpl). Where can I find this option in windows 7? How to solve this?

    Read the article

  • Ubuntu virtual memory caches suck up memory

    - by Tom
    Hey all, I've got an Ubuntu 9.10 64-bit server that seems to use up all available memory. According to my munin graphs, almost all of the memory used up is in the swap cache, cache, and slab cache. (I take this to mean virtual memory caches, am I right in assuming this?) Once memory usage approaches 100%, some (although not all) system services such as SSH become sluggish and unresponsive. After rebooting the system, performance and memory usage become normal for a time. Some interesting tidbits: The system runs Apache 2, MySQL, Munin, and sshd. The memory usage spikes happen at the same time every night (at 10 PM sharp.) There appears to be nothing in the crontab for any of the users, and nothing in /etc/cron.d/* out of the ordinary, let alone something that would occur at 10 PM. My question is, how do I figure out what is causing the memory suckage? I've tried the usual utilities (e.g. ps, top, etc) but I can't seem to find anything unusual. Any ideas? Thanks in advance!

    Read the article

  • CentOS 5.5 ext4 conversion problem - ext4 partition is recognized as ext3

    - by FractalizeR
    Hello. I had 5.4 machine. Upgraded to 5.5 today via yum upgrade. All went fine. Rebooted. Wanted to convert root partition to ext4 (I have three partitions: /boot, / and swap). All of them on software RAID 1 (root is /dev/md2). I did the following for converting yum install e4fsprogs tune2fs -O extents,uninit_bg,dir_index /dev/md2 nano /etc/fstab # I indicated here that my /dev/md2 is of ext4 uname -a mkinitrd -f /boot/initrd-2.6.18-194.3.1.el5.img 2.6.18-194.3.1.el5 Rebooted. I expected fsck to start automatically as said on some site. But it did not. Threw some error (don't remember exactly which). Ok, I booted linux rescue and executed fsck: fsck -t ext4 -fy /dev/md2 Partition went fine. But still when I boot main system, it says in log: "ext3-fs:" then something about not being able to mount ext3 partition due to unknown extended attributed (200). I booted linux rescue again. It loads fine and correctly determines all my machine partitions both ext3 (boot) and ext4 (/) under /mnt/sysimage just fine. I retried mkinitrd thing again watching it's output and ensured ext4 module is included into the system. I also edited menu.lst grub file to include rootfstype=ext4 kernel parameter. Bad luck. I still have message from ext3-fs about not being able to mount filesystem because of attributes and kernel panic immediately after. I checked /etc/fstab - it's fine and saying that root is of ext4. What did I do wrong? This machine is empty so I can just reformat it with 5.5 and recreate partitions to be originally ext4. But... I just want to know what did I do wrong.

    Read the article

  • Ubuntu NBR karmic boot freezes at fsck from util-linux-ng 2.16

    - by BlueBill
    Hi all, I have a netbook (emachine e250 - equivalent to an acer aspire one) and I have Ubunutu NBR 9.10 installed on it. Every other cold boot freezes at the following error message: "fsck from util-linux-ng 2.16" There is no disk activity, no activity what so ever. I have left the machine sit for over an hour and nothing. It takes a couple of hard resets to be able to boot properly. Once it boots everything works great (wireless, suspend/resume, etc.)! I have spent the last couple of weeks researching the problem and the only thing that seems to work is setting nolapic in the boot string in grub - it boots every time. Unfortunately, nolapic disables the second core and causes problems with suspend resume. At first I thought it was an fsck problem with the first partition on the hard disk as it is a hidden ntfs partition containing the windows xp recover information. So in /etc/fstab I set the partition so that it would be ignored by fsck. This didn't seem to do anything. I have these partitions: /dev/sda1 - an ntfs recovery partition /dev/sda2 - /boot /dev/sda3 - swap /dev/sda5 - / /dev/sda6 - /home I am running kernel version 2.6.31-19-generic and have all the patches (as indicated by update manager). I also have no splash screen so I can see the boot progress. I have only been using NBR since January, I have been using Ubuntu on my desktop since last June (2009-06). What logs should I be looking at? Is there a log for failed boots? Thanks, Troy

    Read the article

  • mdadm cron job sends email that cron has run

    - by Andrew
    I've got an Ubuntu 8.04 server using mdadm to create several RAID1 arrays. I created /etc/cron.hourly/mdadm as follows: #! /bin/sh set -e mdadm --monitor /dev/md0 /dev/md3 /dev/md4 --oneshot (Yes, the array numbers are not sequential, and I'm not using --scan beacuse I have a degraded array that may or may not have been used as swap and I can't delete, but I think that's a separate issue. If it's the underlying cause of this, I need to fix it.) mdadm sends me email (configured in the /etc/mdadm/mdadm.conf) on DegradedArray etc. events. This is the desired behaviour. What is not desired, and I can't work out, is why cron is sending me (relatively pointless) emails, via an alias in /etc/aliases: From: root@<hostname> (Cron Daemon) To: root@<hostname> Subject: Cron <root@<hostname>> cd / && run-parts --report /etc/cron.hourly Content-Type: text/plain; charset=ANSI_X3.4-1968 X-Cron-Env: <SHELL=/bin/sh> X-Cron-Env: <PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin> X-Cron-Env: <HOME=/root> X-Cron-Env: <LOGNAME=root> Message-Id: <id@hostname> Date: Fri, 7 May 2010 13:17:01 +0930 (CST) /etc/cron.hourly/mdadm: mdadm: Monitor using email address "<root_alias@domain>" from config file I've got a dozen other servers behaving correctly (mdadm sends email, cron doesnt') with identical /etc/crontab files: # /etc/crontab: system-wide crontab # <snip comments> SHELL=/bin/sh PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin # m h dom mon dow user command 17 * * * * root cd / && run-parts --report /etc/cron.hourly <snip anacron jobs> Should I simply remove the --report, or is there something else in my cron config somewhere causing this?

    Read the article

  • What can cause an increase in inactive memory and how to reclaim it?

    - by Boaz
    Hi All, I have heavy application running on a CentOS server and I'm seeing a strange memory behavior. Here is a snapshot of a munin graph: As you can see the amount of committed memory increases gradually causing the swap file to be use. What strikes me odd is that the amount of inactive memory keeps growing as well. It is my understanding that the inactive memory is actually memory freed up but not yet clean by the OS and put back in the free memory pool. It seems that running out of memory is acutally caused by this lack of clean up, but I may be wrong. Can you give some tips to find the cause of the problem and/or cause CentOS to reclaim the inactive memory? Thanks. Some extra info: 1) I have a tmpfs mounted on /tmp and the number of files stored there grows (but it is double the amount of the inactive memory). 2) cat /proc/meminfo (at a later stage than the image) gives: MemTotal: 14371428 kB MemFree: 1207108 kB Buffers: 35440 kB Cached: 4276628 kB SwapCached: 785316 kB Active: 9038924 kB Inactive: 3902876 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 14371428 kB LowFree: 1207108 kB SwapTotal: 10223608 kB SwapFree: 6438320 kB Dirty: 627792 kB Writeback: 0 kB AnonPages: 7844560 kB Mapped: 49304 kB Slab: 146676 kB PageTables: 27480 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 17409320 kB Committed_AS: 16471488 kB VmallocTotal: 34359738367 kB VmallocUsed: 275852 kB VmallocChunk: 34359462007 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 Hugepagesize: 2048 kB 3) The application is a combination of MySQL, Heritrix (http://crawler.archive.org/ ) and a Tomcat based Java servlet to manage things.

    Read the article

  • ZFS + FreeBSD + virtualbox

    - by John
    Hi, I'm configuring a FreeBSD server hosting virtualbox serving half dozen mission critical busy mail servers. I just learned ZFS, I'm quite attracted, but have a few questions: what is the CPU overhead of ZFS? I googled and found little (or no) benchmark for that. from what I learned, when ZFS updates files, it keeps the old file as snapshot, and write the updated part for the new version. However that would mean for each snapshot it keeps that require significant storage overhead. How much is this storage overhead? For example, suppose I have 2TB usable space, how much space can actually be used for the latest version of files one year later? is FreeBSD with ZFS hosting virtualbox serving half dozen busy guest mission critical mail servers a reasonable combination? Anything particular to be careful with? And can I still choose ZFS for the guest OSs? This is because I may build another identical such box for redundancy, and will need to do some mirroring between each pair of the guest systems across the boxes. I'm trying to configure a Dell R710 for this. From what I learned, I shouldn't choose any RAID at all, is that true? In that case, are the drives still arrive hot swappable? this may sounds a bit pathetic, but since I have no experience with ZFS at all, and this is a mission critical server, so just ask just in case: I'm choosing twin Intel L5630 processors, and 6 x 600GB 15K RPM Serial-Attach SCSI drives. If I need more space in the future, I would just hot swap some drivers with larger capacity to expand the storage. There is no problem with these, right?

    Read the article

  • What can cause an increase in inactive memory and how to reclaim it?

    - by Boaz
    I have heavy application running on a CentOS server and I'm seeing a strange memory behavior. Here is a snapshot of a munin graph: As you can see the amount of committed memory increases gradually causing the swap file to be use. What strikes me odd is that the amount of inactive memory keeps growing as well. It is my understanding that the inactive memory is actually memory freed up but not yet clean by the OS and put back in the free memory pool. It seems that running out of memory is acutally caused by this lack of clean up, but I may be wrong. Can you give some tips to find the cause of the problem and/or cause CentOS to reclaim the inactive memory? Thanks. Some extra info: 1) I have a tmpfs mounted on /tmp and the number of files stored there grows (but it is double the amount of the inactive memory). 2) cat /proc/meminfo (at a later stage than the image) gives: MemTotal: 14371428 kB MemFree: 1207108 kB Buffers: 35440 kB Cached: 4276628 kB SwapCached: 785316 kB Active: 9038924 kB Inactive: 3902876 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 14371428 kB LowFree: 1207108 kB SwapTotal: 10223608 kB SwapFree: 6438320 kB Dirty: 627792 kB Writeback: 0 kB AnonPages: 7844560 kB Mapped: 49304 kB Slab: 146676 kB PageTables: 27480 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 17409320 kB Committed_AS: 16471488 kB VmallocTotal: 34359738367 kB VmallocUsed: 275852 kB VmallocChunk: 34359462007 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 Hugepagesize: 2048 kB 3) The application is a combination of MySQL, Heritrix (http://crawler.archive.org/ ) and a Tomcat based Java servlet to manage things.

    Read the article

  • What can cause an increase in inactive memory and how to reclame it?

    - by Boaz
    Hi All, I have heavy application running on a CentOS server and I'm seeing a strange memory behavior. Here is a snapshot of a munin graph: As you can see the amount of committed memory increases gradually causing the swap file to be use. What strikes me odd is that the amount of inactive memory keeps growing as well. It is my understanding that the inactive memory is actually memory freed up but not yet clean by the OS and put back in the free memory pool. It seems that running out of memory is acutally caused by this lack of clean up, but I may be wrong. Can you give some tips to find the cause of the problem and/or cause CentOS to reclaim the inactive memory? Thanks. Some extra info: 1) I have a tmpfs mounted on /tmp and the number of files stored there grows (but it is double the amount of the inactive memory). 2) cat /proc/meminfo (at a later stage than the image) gives: MemTotal: 14371428 kB MemFree: 1207108 kB Buffers: 35440 kB Cached: 4276628 kB SwapCached: 785316 kB Active: 9038924 kB Inactive: 3902876 kB HighTotal: 0 kB HighFree: 0 kB LowTotal: 14371428 kB LowFree: 1207108 kB SwapTotal: 10223608 kB SwapFree: 6438320 kB Dirty: 627792 kB Writeback: 0 kB AnonPages: 7844560 kB Mapped: 49304 kB Slab: 146676 kB PageTables: 27480 kB NFS_Unstable: 0 kB Bounce: 0 kB CommitLimit: 17409320 kB Committed_AS: 16471488 kB VmallocTotal: 34359738367 kB VmallocUsed: 275852 kB VmallocChunk: 34359462007 kB HugePages_Total: 0 HugePages_Free: 0 HugePages_Rsvd: 0 Hugepagesize: 2048 kB

    Read the article

  • Distributed development staff needing a common IP range

    - by bakasan
    I work on a development staff that is geographically distributed, mostly all throughout the state of CA, but several key members also must travel frequently. We rely quite heavily on a 3rd party provider API for a great deal of our subsystems (can't get into who it is or what they do). The 3rd party however is quite stringent on network access and have no notion of a development sandbox. Access is restricted to 2, 3 IP numbers and that's about it. Once we account for our production servers, that leaves us with an IP or two to spare for our dev team--which is still problematic as people's home IP changes, people travel, we have more than 2 devs, etc. Wide IP blocks are not permitted by the 3rd party. Nor will they allow dynamic DNS type services. There is no simple console to swap IPs on the fly either (e.g. if a dev's IP at home changes or they are on the road). As none of us are deep network experts, I'm wondering what our viable options are? Are there such things as 3rd party hosts to VPNs? Generally I think of a VPN as a mechanism to gain access to a home office, but the notion would be a 3rd party VPN that we'd all connect to and we'd register this as an IP origin w/ our 3rd party. We've considered using Amazon EC2 to effectively host a dev environment for each dev and using that to connect. Amazon only gives you so many static IPs however (I believe 5?) so this would only be a stop gap solution until our team size out strips our IP count at Amazon. Those were the only viable thoughts that I had, but again, I'm far from a networking guy. Tried searching for similar threads, but I'm not even sure I know the right vernacular to look around for.

    Read the article

  • Apache MaxClients reaching max and locking the server

    - by Rodrigo Sieiro
    Hi. I currently have an Apache2 server running with mpm-prefork and mod_php on a OpenVZ VPS with 512M real / 1024M burstable RAM (no swap). After running some tests, I found that the maximum process size Apache gets is 23M, so I've set MaxClients to 25 (23M x 25 = 575 MB, ok for me). I decided to run some load tests on my server, and the results left me puzzled. I'm using ab on my desktop machine requesting the main page from a wordpress blog. When I run ab with 24 concurrent connections, everything seems fine. Sure, CPU goes up, free RAM goes down, and the result is about 2-3s response time per request. But if I run ab with 25 concurrent connections (my server limit), Apache just hangs after a couple of seconds. It starts processing the requests, then it stops responding, CPU goes back to 100% idle and ab times out. Apache log says it reached MaxClients. When this happens, Apache keeps itself locked up with 25 running processes (they're all in "W" if I check server status) and only after the TimeOut setting the processes start to die and the server starts responding again (in my case it's set to 45). My question: is that expected behaviour? Why Apache just dies when it reaches MaxClients? If it works with 24 connections, shouldn't it work with 25, just taking maybe more time to respond each request and queueing up the rest? It sounds kinda strange to me that any kid running ab can alone kill a webserver just by setting the concurrent connections to the servers MaxClients.

    Read the article

  • Apache reaching MaxClients and locking the server

    - by Rodrigo Sieiro
    Hi. I currently have an Apache2 server running with mpm-prefork and mod_php on a OpenVZ VPS with 512M real / 1024M burstable RAM (no swap). After running some tests, I found that the maximum process size Apache gets is 23M, so I've set MaxClients to 25 (23M x 25 = 575 MB, ok for me). I decided to run some load tests on my server, and the results left me puzzled. I'm using ab on my desktop machine requesting the main page from a wordpress blog. When I run ab with 24 concurrent connections, everything seems fine. Sure, CPU goes up, free RAM goes down, and the result is about 2-3s response time per request. But if I run ab with 25 concurrent connections (my server limit), Apache just hangs after a couple of seconds. It starts processing the requests, then it stops responding, CPU goes back to 100% idle and ab times out. Apache log says it reached MaxClients. When this happens, Apache keeps itself locked up with 25 running processes (they're all in "W" if I check server status) and only after the TimeOut setting the processes start to die and the server starts responding again (in my case it's set to 45). My question: is that expected behaviour? Why Apache just dies when it reaches MaxClients? If it works with 24 connections, shouldn't it work with 25, just taking maybe more time to respond each request and queueing up the rest? It sounds kinda strange to me that any kid running ab can alone kill a webserver just by setting the concurrent connections to the servers MaxClients.

    Read the article

  • Verification of files on backup media - after the backup

    - by Greg Sansom
    I have a system in place where I back up my work files daily to a portable hard drive. I actually have two portable hard drives - one is stored off-site and I swap them regularly. I also keep my family photos and other historical files backed up, but I only back the photos up occasionally (ie when I have new photos). The backup media is for backup only, and it is unlikely I will ever read the files from the backup media unless a disaster occurs and I lose the master. It worries me that my backed up files could become corrupt without me knowing it. It is also feasible that my master files could become corrupt, and eventually the corrupt files would be replicated to the backup media. I'm currently using Cobian Backup, but I'm open to alternatives. Is there a tool I can use to confirm that the backed up files are identical to the files that were first copied? I know it would be possible to generate a checksum and periodically validate the backup files against the original checksum, but I'm looking for a tool which will do this automatically.

    Read the article

  • Experience with AMCC 3ware 9650se raid cards? Ours seems dead

    - by antiduh
    We have a 8-port 3ware 9650se raid card for our main disk array. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. This card has been in service for a couple years without problems, and was working up until the shutdown. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS. The OS eventually boots, but alas, without the card. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. Has anybody performed a card swap before? Any help would be greatly appreciated. Edit: These are the kernel errors we see: 3ware 9000 Storage Controller device driver for Linux v2.26.02.012. 3w-9xxx 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 3w-9xxx 0000:09:00.0: setting latency timer to 64 3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing. 3w-9xxx: scsi0: ERROR: (0x06:0x001F): Microcontroller not ready during reset sequence. 3w-9xxx: scsi0: ERROR: (0x06:0x0036): Response queue (large) empty failed during reset sequence. 3w-9xxx 0000:09:00.0: PCI INT A disabled

    Read the article

  • process and memory issue on linux server

    - by zapping
    Need some assistance in analyzing apache and php process running on linux server. Its a 8-core intel processor with 4GB ram. When the website on it runs the top displays like this. PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 23459 username1 16 0 151m 27m 8388 S 11.3 0.7 0:11.71 php5 23730 username1 16 0 151m 28m 8388 S 11.3 0.7 0:03.87 php5 23458 username1 16 0 151m 28m 8388 S 3.0 0.7 0:19.20 php5 16202 mysql 15 0 459m 38m 4624 S 0.7 1.0 62:33.81 mysqld 24141 nobody 15 0 311m 5832 2304 S 0.3 0.1 0:00.03 httpd Why does the command say php5 when the website is accessed. Both apache and php was preconfigured so not sure whats done there. Tried setting up the same site and db on a different server but on it the process shows httpd always and not php5. The site uses mysql db. The problem is server load seems to go till about 5.x when the website was access by about 16users. When the free -m command was given the output shows total used free shared buffers cached Mem: 3941 3727 213 0 236 2734 -/+ buffers/cache: 756 3184 Swap: 4095 0 4095 Lots of memory seems to be in cache and free memory is less. Even when the website is not accessed that is leaving it very much idle for about 2days the free memory showed just 190. When the site is accessed the free memory seems to be go till 90mb then it increases to about 150mb. It always seems to remain just about 200mb. Is it somehow related to the server load showing 5.x. Will adding some more RAM resolve the load issue?

    Read the article

  • Linux error when resume from RAM

    - by TuxPotato
    The last two times that I have resumed my laptop from sleep, it has hung and given me this set of errors: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 hda_intel: azx_get_responce timeout, switching to single_cmd mode: last cmd=0x01170700 ata6: softreset failed (device not ready) ata4: softreset failed (device not ready) [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 The last two messages repeat two more times. The first time this happened, Linux's Magic SysRq worked and did a soft reboot, and after that everything was fine till it went to sleep again. It wakes up and gives me this. Here are the laptop stats: Toshiba Satellite L455D-S5976 AMD Sempron SI-42 Processor 2GB DDR2 RAM HD TruBrite Display ATI Radeon Graphics (integrated) Running Ubuntu 10.10 32 bit I'm not sure about the hard drive, but its a 250GB drive with one NTFS partition, two Hidden NTFS, one Linux Swap, and one Ext4. Can someone tell me whats wrong with my laptop? NOTE: This only happens when I close the screen. My computer doesn't go to sleep with the screen open.

    Read the article

< Previous Page | 59 60 61 62 63 64 65 66 67 68 69 70  | Next Page >